Quadrafire 3100 Millennium Le manuel du propriétaire

Marque
Quadrafire
Modèle
3100 Millennium
Catégorie
Cheminées
Taper
Le manuel du propriétaire
1 7033-329B June 7, 2017
NOTICE: DO NOT DISCARD THIS MANUAL
O-T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
3100 Millennium Wood Appliance
Model(s):
31M-ACC-MBK
Owner’s Manual
Operation & Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with question on installation, operation, or service.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may over-re and generate
poisonous gases (i.e. carbon monoxide).
HOT SURFACES!
Glass and other surfaces are hot
during operation AND cool down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high temperatures
• High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other ammable
materials away.
WARNING
If the information in these instruc-
tions is not followed exactly, a
re could result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of
this or any other appliance.
• Do not over-re - If appliance or chim-
ney connector glows, you are over-ring.
Over-ring will void your warranty.
• Comply with all minimum clearances to
combustibles as specied. Failure to
comply may cause house re.
WARNING
NOTE
To obtain a French translation of this manual, please contact
your dealer or visit www.quadrare.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrare.com
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
2 7033-329B June 7, 2017
3100 Millennium Wood Appliance
CONFIDENTIAL PROPERTY OF HEARTH & HOME TECHNOLOGIES INC.
PART NAME:
DRAWN BY:
SCALE:
MATERIAL:
SHEET:
PART NUMBER:
REV:
THIS PRINT IS CHECKED AND CONTROLLED BY THE ENGINEERING
DEPARTMENTS OF HEARTH & HOME TECHNOLOGIES INC.
ECO # DATE BYREV
UNLESS OTHERWISE SPECIFIED DIMS ARE INCHES[MM] & : TOLERANCES ARE: (2) PLACE DEC : ± 0.03 (3) PLACE DEC: ± 0.005 ANGLE: ± 2° FRACTION: ± 1/16
OUTSIDE MATERIAL. NORMAL DIM & INSIDE MATERIAL.
OUTSIDE APEX
INSIDE APEX - DIMS ENCLOSED BY AN OVAL ARE CRITICAL DIMENSIONS
REVISIONS
ITEM PART NUMBER PART NAME QTY
LABEL
XXX NTS SEE NOTE
1 OF 1
7033-278 10
NOTE:
1. MATERIAL: NON-ANODIZED ALUMINUM 0.020 THICK
2. BACKGROUND: SILVER
3. COPY: BLACK & RED
4. ADHESIVE: 3M #468 PERMANENT ACRYLIC
5. TEMPERATURE RATING: -50 F TO 350 F
ECO
10
UPDATE TO REFLECT HALIFAX CHANGES
84782 03/21/17 TPS
G FIXED METRIC DIMENSION ERROR (ITEM A FLAT TOP MODEL) 76211 12/16/14 BLW
H UPDATED FOR NSPS STANDARD 77523 05/04/15 TMM
I MODEL DESIGNATION & SERIAL # PREFIX & UPDATED FLR PR. 82062 11/16/16 IJW
1 7033-278
SERIAL RATING PLATE
1
7.75
9.5
INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH
MINIMUM
2 FOOT VERTICAL OFF STOVE TOP
INSTALLATION: ENTIÈREMENT VERTICALE OU HORIZONTALE AVEC 609mm VERTICAL
MINIMUM
DU HAUT DU POÊLE
SINGLE WALL PIPE
A B C D E F G H
Flat Top Model 15.25 (387) 11.75 (298) 25.5 (648) 16 (406) 8 (203) 17 (432) 48 (1220) 12 (305)
Step Top Model 12 (305) 8.5 (216) 22 (559) 12.5 (318) 5.5 (140) 14.5 (368) 48 (1220) 12 (305)
DOUBLE WALL PIPE
Flat Top Model 10.5 (267) 6.5 (165) 22 (559) 13 (330) 6.5 (165) 15.5 (394) 48 (1220) 9 (229)
Step Top Model
10
(254) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)
INSTALLATION: 90
o
ELBOW OFF TOP OF STOVE THROUGH BACKWALL
INSTALLATION: 90
o
DU COURBURE AU DESSUS DE HAUT DU PO
Ê
LE A TRAVERS LE MUR ARRIÈRE
SINGLE WALL PIPE
Flat Top Model 12 (305) 8.5 (216) 22 (559) 13 (330) 8 (203) 17 (432) 48 (1220) 12 (305)
Step Top Model 10 (254) 6 (152) 20.5 (521) 11 (279) 5.5 (140) 14.5 (368) 48 (1220) 12 (305)
DOUBLE WALL PIPE
Flat Top Model 8 (203) 4.5 (114) 17.5 (445) 8.5 (216) 6.5 (165) 15.5 (394) 48 (1220) 9 (229)
Step Top Model 10 (254) 6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330) 48 (1220) 9 (229)
INSTALLATION: ALCOVE - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT* listed factory-built Class "A" chimney, or a masonry
chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of
unit, and the referenced clearances.
INSTALLATION: ALCÔVE - De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT de Classe "A", ou une
cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une hauteur
minimum de 48 inches (1220mm) du haut de l'appareil, et des espaces libres alloués.
DOUBLE WALL PIPE
Flat Top Model 11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368) N/A N/A 48 (1220) *
Step Top Model
10 (254) 6 (152) 20.5 (521) 11 (279) N/A N/A 48 (1220) *
*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650
o
C
Factory-built chimney.
*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650
o
C cheminée bâtit en usine.
* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED / VOIR LE FABRICANT POUR LES ESPACES LIBRES DES CONDUIT - PAS TESTÉ
SPÉCIFICATIONS DE LA VENTILATION:
MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de minimum
d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en usine UL103HT* de
Classe "A", adéquate pour usage avec les combustions solides, ou une cheminée de briques,
avec espaces libres référés.
MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé
pour mur double avec une cheminée bâtit en usine UL103HT* de Classe "A:, ou une cheminée
de briques, avec espaces libres alloués.
MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk Metalbestos
DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les espaces libres pour mur
double comme mentionné ci-bas.
ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:En Pouces & (millimètres)
NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de l'entrée du conduit.
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES. (UM) 84
HUD . "For Use with Solid Wood Fuel Only"
I
nstall and use only in accordance with
manufacturer's installation and operating
instructions. Contact local building or fire
officials about restrictions and installation
inspections in your area. Do not obstruct the
space beneath heater.
For use with leg and
pedestal options intended for this model,
refer to owner’s manual for appropriate part
numbers and installation instructions.
WARNING - For Mobile Homes: Do not
install in a sleeping room. An outside
combustion air inlet must be provided and
unrestricted while unit is in use. The
structural integrity of the mobile home floor,
ceiling and walls must be maintained. The
stove needs to be properly grounded to the
frame of the mobile home. Components
required for mobile home installation:
Outside Air Kit, Part Number OAK-ACC..
Refer to manufacturer's instructions and
local codes for precautions required for
passing chimney through a combustible
wall or ceiling and maximum offsets.
Inspect and clean chimney frequently -
Under Certain Conditions of Use, Creosote
Buildup May Occur Rapidly.
Do not connect this unit to a chimney
serving another appliance.
Optional Blower, Part BK-ACC.
Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.
Route power cord away from unit. Do not
route cord under or in front of appliance.
DANGER: Risk of electrical shock.
Disconnect power supply before servicing.
Replace glass only with 5mm ceramic
available from your dealer.
Do not use grate or elevate fire. Build
wood fire directly on hearth.
Do not overfire - if heater or chimney
connector glows, you are overfiring.
Operate only with the fuel loading door
closed. Open only to add fuel to the fire.
CAUTION:
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2015 particulate emission standards at 1.1 G/HR
EPA Method 28 and 5G. Not approved for sale after May 15, 2020.
This wood heater needs periodic inspection and repair for proper
operation. Consult the owner’s manual for further information. It is against
federal regulations to operate this wood heater in a manner inconsistent
with the operating instructions in the owner’s manual.
PREVENT HOUSE FIRES
FLOOR PROTECTION
:
Floor protector for Millennium and Pedestal Step Top Models
must be a 3/8 inch min. thickness, non-combustible material or
equivalent, (Step Top Leg Model only require non-combustible
TypeII floor protector R=1.19 or greater extending beneath
heater and to front/sides/rear as indicated on the diagram
below. Exception: Non-combustible floor protections must
extend beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side.
Report / Rapport
0061WS066S
TESTED TO:/ TESTÉ À:
UL 1482-11 (R2015) , ULC S627-00.
HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP FURNISHINGS
AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS.
VENT SPECIFICATIONS:
SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or
blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney,
suitable for use with solid fuels, or a masonry chimney, and the referenced
clearances.
DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air
insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a
masonry chimney and the referenced clearances
MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or
Security DL double wall connector pipe. Must be equipped with a spark arrestor.
Apply double wall clearances below when installing unit.
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.
R
7033-278_R10
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES
BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS
.
ATTENTION:
APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE
COMBUSTIBLE SOLIDE, POUR USAGE DANS LES
MAISONS MOBILES. (UM) 84 HUD. "Pour Usage Avec
Bois Solide Seulement"
Installez et utilisez en accord avec les instructions
d'installation et d'opération du fabricant. Contactez le
bureau de la construction ou le bureau des incendies au
sujet des restrictions et des inspections d'installation dans
votre voisinage. Ne pas obstruez l'espace en dessous de
l'appareil.
AVIS - Pour Les Maisons Mobiles: Ne pas installer dans
une chambre à coucher. Un tuyau extérieur de combustion
d'air doit être installé et ne doit pas être obstrué lorsque
l'appareil est en usage. La structure intégrale du plancher,
du plafond et des murs de la maison mobile doit être
maintenue intacte. L'appareil de chauffage doit être fixé à
la charpente de la maison mobile. Les composants requis
pour l'installation des maisons mobiles: Assemblage d'air
extérieur, Numéro de Pièce OAK-ACC.
R
éférez vous aux instructions du fabricant et des codes
locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles, et
les compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Sous
certaines conditions, il se peut que la créosote s'accumule
rapidement.
Ne pas connecter cet appareil à une cheminée servant un autre
appareil.
tVentilateur Optionnel, Pièce BK-ACC.
Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.
Éloignez le fil électrique de l'appareil. Ne pas faire passer
le fil électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique.
Déconnectez le fil électrique de la prise de contact avant
le service.
Remplacez la vitre seulement avec une vitre céramique de
5 mm disponible chez votre fournisseur.
N'élevez pas le feu. Bâtissez le feu de bois directement
sur l'âtre.
Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau
de cheminée rougissent, vous surchauffez.
Opérez l'appareil seulement lorsque la porte de
chargement est fermée. Ouvrez la porte seulement
lorsque vous devez ajouter des combustibles dans le feu.
PRÉVENTION DES FEUX DE MAISON
PROTECTION DU PLANCHER:
Le protecteur de plancher doit être (
Modèles
Millennium et
au
dessus en escalier socle)
d'un minimum de 3/8 inch (9.5 mm)
d'épaisseur, de matériel incombustible ou équivalent, (
Modèle
au
dessus en escalier
pied d’un minimum de 1/2 inch [13mm]
d'épaisseur, “k” =0.84, R value 0.59 au le protecteur de
plancher de matériel incombustible 1-1/4 inch [32mm]
d’épaisseur). s'étendant du dessous de l'appareil de chauffage
à l'avant, aux cotés et à l'arrière comme indiqué sur le
diagramme suivant. Exception: Les protections incombustibles
du plancher doivent s'étendre en dessous du conduit de
cheminée lorsqu'installées avec une ventilation à l'horizontale et
s'étendre de 2 inches (51mm) de chaque côté.
BACKWALL/SIDEWALL
MUR ARRIÈRE/MUR DE CÔTÉ
CORNER INSTALLATION
INSTALLATION DU COIN
ALCOVE TOP VIEW /
VUE DU HAUT DE L'ALCÔVE
ALCOVE SIDE VIEW /
VUE DE CÔTÉ DE L'ALCÔVE
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
CONDUIT DU MUR SIMPLE
CONDUIT DU MUR DOUBLE
CONDUIT DU MUR DOUBLE
Manufactured by:
Fabriqué par:
C
D
A
B
C
D
90
o
OFF TOP
UP & OUT CEILING CLEARANCE
ESPACE LIBRE DU DESSUS DE
L'APPAREIL AU PLAFOND AVEC 90
DE COURBURE
STOVE TO CEILING CLEARANCE
ESPACE LIBRE DU POÊLE AU
PLAFOND
GG
H*
E
F
E
F
CONDUIT DU MUR DOUBLE
Modèle au dessus en appartement
Modèle au dessus en escalier
Modèle au dessus en escalier
G
H
*
Modèle au dessus en appartement
Modèle au dessus en escalier
Modèle au dessus en appartement
Modèle au dessus en escalier
Modèle au dessus en appartement
CONDUIT DU MUR SIMPLE
Modèle au dessus en appartement
Modèle au dessus en escalier
352 Mountain House Road, Halifax, PA 17032
www.quadrafire.com
G
A
B
G
A
B
3100 ACC Series
O-T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
16" from glass
8"
USA
Fuel loading door
Millennium & Step Top 31-5/8" Min
Millennium
& Step Top
39”
minimum
CANADA
203mm (8")
203mm
(8")
203mm
(8")
457mm (18")
Millennium
1280mm
(50-3/8")
minimum
1040mm (41") minimum
Step Top
1321mm
(52")
minimum
Made in U.S.A. of US and
imported parts.
Fabriqué aux
États-Unis-d’Amérique par des
pièces d’origine américaine et
pièces importées.
2017 2018 2019 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.
31 MILLENIUM DISCOVERY II
Serial No. / N° de série
HF
BARCODE LABEL
Serial No.
Model
Name
Test Lab &
Report No.
Mfg. Date
SAMPLE
A. Sample of Serial Number / Safety Label
LOCATION: Back of appliance
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
June 7, 2017 7033-329B 3
3100 Millennium Wood Appliance
TABLE OF CONTENTS
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
A. Sample of Serial Number / Safety Label ...........................2
B. Warranty Policy ..................................................................4
C. Quick Start Guide ..............................................................6
1 Listing and Code Approvals .............7
A. Appliance Certication ......................................................7
B. BTU & Efciency Specications........................................7
C. Mobile Home Approved ....................................................7
D. Glass Specications .........................................................7
2 Operating Instructions ......................8
A. Over-Firing Your Appliance ...............................................8
B. Wood Selection & Storage ................................................8
C. Burning Process ...............................................................8
D. Air Controls .......................................................................9
E. Using Burn Rate Air Control & ACC System ....................9
F. Burn Rates and Operating Efciency ...............................10
G. Building A Fire .................................................................11
H. Correct Bafe & Blanket Placement .................................12
I. Blower Operating Instructions ...........................................13
J. Opacity (Smoke) ...............................................................13
K. Clear Space ......................................................................14
L. Negative Pressure.............................................................14
M. Frequently Asked Questions ............................................15
3 Maintenance and Service. ...............16
A. Quick Reference Maintenance Guide ................................16
B. General Maintenance .......................................................17
4 Troubleshooting Guide. ...................18
5 Service Part Replacement. ..............19
A. Glass Replacement ..........................................................19
B. Firebrick Replacement .....................................................19
C. Snap Disc Replacement ...................................................19
D. Door Handle Assembly ....................................................20
E. Bafe Removal ................................................................20
F. Tube Channel Assembly Replacement ............................21
6 Reference Materials .........................22
A. Service & Maintenance Log ...............................................22
B. Service Parts & Accessories ..............................................24
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
4 7033-329B June 7, 2017
3100 Millennium Wood Appliance
slenap yrotcarfer dedloMX
4021-645H 10/15 Page 1 of 2
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT
gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-
nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
See conditions, exclusions, and limitations on next page.
Parts Labor Gas Wood Pellet
EPA
Wood
Coal Electric Venting
XXXXX X X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
XXX
Igniters, electronic components
,
and glass
srewolb dellatsni-yrotcaFXXXXX
stopnrub dna stoperiFX
selffab dna sgnitsaCXXraey 1sraey 5
7 years 3 years XXX
Manifold tubes,
HHT chimney and termination
10
years
yrotcarfer dna sgol ,srenruBXraey 1
Limited
Lifetime
dna xoberiFXXXXXsraey 3 heat exchanger
XXXXX X X
All replacement parts
beyond warranty period
Warranty Period HHT Manufactured Appliances and Venting
1 Year
Components Covered
3 years
2 years
90 Days
X
Ignition Modules
B. Warranty Policy
June 7, 2017 7033-329B 5
3100 Millennium Wood Appliance
WARRANTY CONDITIONS:
• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of
HHT authorized dealers is available on the HHT branded websites.
• This warranty is only valid while the HHT appliance remains at the site of original installation.
• This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance
resides.
• Contact your installing dealer for warranty service. If the installing dealer is unable to provide necessary parts, contact
the nearest HHT authorized dealer or supplier. Additional service fees may apply if you are seeking warranty service
from a dealer other than the dealer from whom you originally purchased the product.
• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges
for parts are not covered by this warranty.
This warranty is void if:
• The appliance has been over-fired or operated in atmospheres contaminated by chlorine, fluorine, or other damaging
chemicals. Over-firing can be identified by, but not limited to, warped plates or tubes, rust colored cast iron, bubbling,
cracking and discoloration of steel or enamel finishes.
• The appliance is subjected to prolonged periods of dampness or condensation.
• There is any damage to the appliance or other components due to water or weather damage which is the result of, but
not limited to, improper chimney or venting installation.
LIMITATIONS OF LIABILITY:
• The owner’s exclusive remedy and HHT’s sole obligation under this warranty, under any other warranty, express or
implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above. In no
event will HHT be liable for any incidental or consequential damages caused by defects in the appliance. Some states
do not allow exclusions or limitation of incidental or consequential damages, so these limitations may not apply to you.
This warranty gives you specific rights; you may also have other rights, which vary from state to state. EXCEPT TO
THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
• Changes in surface finishes as a result of normal use. As a heating appliance, some changes in color of interior and
exterior surface finishes may occur. This is not a flaw and is not covered under warranty.
• Damage to printed, plated, or enameled surfaces caused by fingerprints, accidents, misuse, scratches, melted items,
or other external sources and residues left on the plated surfaces from the use of abrasive cleaners or polishes.
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period. These parts
include: paint, wood, pellet and coal gaskets, firebricks, grates, flame guides, batteries and the discoloration of glass.
• Expansion, contraction, or movement of certain parts causing noise. These conditions are normal and complaints
related to this noise are not covered by this warranty.
• Damages resulting from: (1) failure to install, operate, or maintain the appliance in accordance with the installation
instructions, operating instructions, and listing agent identification label furnished with the appliance; (2) failure to
install the appliance in accordance with local building codes; (3) shipping or improper handling; (4) improper opera-
tion, abuse, misuse, continued operation with damaged, corroded or failed components, accident, or improperly/
incorrectly performed repairs; (5) environmental conditions, inadequate ventilation, negative pressure, or drafting
caused by tightly sealed constructions, insufficient make-up air supply, or handling devices such as exhaust fans or
forced air furnaces or other such causes; (6) use of fuels other than those specified in the operating instructions; (7)
installation or use of components not supplied with the appliance or any other components not expressly authorized
and approved by HHT; (8) modification of the appliance not expressly authorized and approved by HHT in writing;
and/or (9) interruptions or fluctuations of electrical power supply to the appliance.
• Non-HHT venting components, hearth components or other accessories used in conjunction with the appliance.
• Any part of a pre-existing fireplace system in which an insert or a decorative gas appliance is installed.
• HHT’s obligation under this warranty does not extend to the appliance’s capability to heat the desired space. Informa-
tion is provided to assist the consumer and the dealer in selecting the proper appliance for the application. Consider-
ation must be given to appliance location and configuration, environmental conditions, insulation and air tightness of
the structure.
4021-645H 10/15 Page 2 of 2
6 7033-329B June 7, 2017
3100 Millennium Wood Appliance
C. Quick Start Guide
ITEMS NEEDED FOR FIRST FIRE:
10 Pieces of Newspaper, 10-20 Pieces of Dry Kindling
and a Few Pieces of Dry Split Wood.
Note: These are generic drawings and may not represent your specific model.
OPEN AIR
CONTROLS
1 2 3
LOAD WOOD ADD NEWSPAPER
4
5
6 7
ADD KINDLING
WARNING! Risk of Fire
Close and securely latch the door after
the fire has started, and after refueling, to
prevent:
-Spillage of smoke, flame and carbon
monoxide
-Spillage of sparks, coals, and logs
-Over firing
DO NOT leave the appliance unattended
with the door open.
Starting a fire may not require an open
door for draft. The air control should
supply adequate draft.
ADD MORE WOOD
REDUCE AIR
CONTROLS
Ser to desired heat output.
The appliance is ready
for normal operation.
HIGH
BURN RA
TE
CONTROL
(Upper Right
Corner)
AUTOMATIC
COMBUSTION
CONTROL (ACC)
(Middle right hand side)
HIGH
LIGHT THE PAPER
LOW
BURN RATE
CONTROL
(Upper Right
Corner)
AUTOMATIC
COMBUSTION
CONTROL (ACC)
(Middle right hand side)
LOW
June 7, 2017 7033-329B 7
3100 Millennium Wood Appliance
The Quadra-Fire 3100 Millennium Wood Appliance (ACC)
meets the U.S. Environmental Protection Agency’s 1990
particulate emission standards.
Model:
3100 Millennium Wood Appliance
Laboratory: OMNI Test Laboratories, Inc.
Report No:
0061WS066S
Type:
Listed Room Appliance, Solid Fuel
Type
Standard: UL1482-11 (R2015) and ULC S627-
00 and (UM) 84-HUD, Mobile Home
Approved.
This wood appliance needs periodic inspection and repair for
proper operation. It is against federal regulations to operate
this wood appliance in a manner inconsistent with operating
instructions in this manual.
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved by
Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with
appliance).
• Do NOT Over re - If appliance or chimney connector glows,
you are over ring.
Any such action that may cause a re hazard.
1 Listing and Code Approvals
A. Appliance Certication
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specications and/or price without notice.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with (UM) 84-HUD and
NFPA211 in the U.S.A. and CAN/CSA-B365 Installation Codes in
Canada.
C. Mobile Home Approved
• This appliance is approved for mobile home installa-
tions when not installed in a sleeping room and when
an outside combustion air inlet is provided.
• The structural integrity of the mobile home oor, ceil-
ing, and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home with #8 copper ground wire, and
chimney must be listed to UL103 HT or a listed UL-
1777 full length six inch (152mm) diameter liner must
be used.
• Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided by,
the following actions:
B. BTU & Efciency Specications
D. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please con-
tact your dealer for replacement glass.
EPA Certication #: 649
EPA Certied Emissions: 1.1 grams per hour
*LHV Tested Efciency: 79.9%
**HHV Tested Efciency: 74%
***EPA BTU Output: 11,700 to 32,000 / hr.
****Peak BTU/Hour Output: 57,200
Vent Size: 6 inches
Firebox Size: 2 cubic feet
Recommended Wood Length: 16 inches
Fuel Orientation: Front-to-Back
Fuel Seasoned Cord Wood
*Weighted average LHV (Low Heating Value) efciency using
Douglas Fir dimensional lumber and data collected during EPA
emission test. LHV assumes the moisture is already in a vapor
state so there is no loss in energy to vaporize.
**Weighted average HHV (High Heating Value) efciency using
Douglas Fir dimensional lumber and data collected during EPA
emission test. HHV includes the energy required to vaporize the
water in the fuel.
***A range of BTU outputs based on EPA Default Efciency and
the burn rates from the low and high EPA tests, using Douglas
Fir dimensional lumber.
****A peak BTU out of the appliance calculated using the max-
imum rst hour burn rate from the High EPA Test and the BTU
content of cord wood (8600) times the efciency.
8 7033-329B June 7, 2017
3100 Millennium Wood Appliance
User Guide
2 Operating Instructions
1. Symptoms of Over-Firing
Symptoms of over-ring may include one or more of the
following:
• Chimney connector or appliance glowing
• Roaring, rumbling noises
• Loud cracking or banging sounds
• Metal warping
• Chimney re
2. What To Do if Your Appliance is Over-Firing
• Immediately close the door and air controls to reduce
air supply to the re.
• If you suspect a chimney re, call the re department
and evacuate your house.
• Contact your local chimney professional and have your
appliance and appliance pipe inspected for any dam-
age.
• Do not use your appliance until the chimney profes-
sional informs you it is safe to do so.
Hearth & Home Technologies WILL NOT warranty applianc-
es that exhibit evidence of over-ring. Evidence of over-r-
ing includes, but is not limited to:
• Warped air tube
• Deteriorated refractory brick retainers
• Deteriorated bafe and other interior components
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover, out
of the rain and snow. Dry and well-seasoned wood will not
only minimize the chance of creosote formation, but will give
you the most efcient re. Even dry wood contains at least
15% moisture by weight, and should be burned hot enough
to keep the chimney hot for as long as it takes to dry the
wood out - about one hour. It is a waste of energy to burn
unseasoned wood of any kind.
A. Over-Firing Your Appliance
Dead wood lying on the forest oor should be considered wet,
and requires full seasoning time. Standing dead wood can
be considered to be about 2/3 seasoned. To tell if wood is
dry enough to burn, check the ends of the logs. If there are
cracks radiating in all directions from the center, it is dry. If
your wood sizzles in the re, even though the surface is dry,
it may not be fully cured.
Splitting wood before it is stored reduces drying time. Wood
should be stacked so that both ends of each piece are
exposed to air, since more drying occurs through the cut ends
than the sides. This is true even with wood that has been
split. Store wood under cover, such as in a shed, or covered
with a tarp, plastic, tar paper, sheets of scrap plywood, etc.,
as uncovered wood can absorb water from rain or snow,
delaying the seasoning process.
C. Burning Process
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order to
improve the situation, we at Quadra-Fire have developed
cleaner-burning wood appliances that surpass the require-
ments for emissions established by our governing agencies.
These wood appliances, like any other appliances, must be
properly operated in order to insure that they perform the way
they are designed to perform. Improper operation can turn
most any wood appliance into a smoldering environmental
hazard.
1. Kindling or First Stage
It helps to know a little about the actual process of burning in
order to understand what goes on inside a appliance. The rst
stage of burning is called the kindling stage. In this stage, the
wood is heated to a temperature high enough to evaporate the
moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
until the water is evaporated. This process takes heat from
the coals and tends to cool the appliance.
Fire requires three things to burn - fuel, air and heat. So, if
heat is robbed from the appliance during the drying stage, the
new load of wood has reduced the chances for a good clean
burn. For this reason, it is always best to burn dry, seasoned
rewood. When the wood isn’t dry, you must open the air
controls and burn at a high burn setting for a longer time to
start it burning. The heat generated from the re should be
warming your home and establishing the ue draft, not evap-
orating the moisture out of wet, unseasoned wood, resulting
in wasted heat.
2. Second Stage
The next stage of burning, the secondary stage, is the period
when the wood gives off ammable gases which burn above
the fuel with bright ames. During this stage of burning it is
Fire Risk
Do not over-re.
Over-ring may ignite creosote or will damage the
appliance and chimney.
To prevent over-ring your appliance, DO NOT:
• Use ammable liquids
• Overload with wood
• Burn trash or large amounts of scrap lumber
• Permit too much air to the re
WARNING
June 7, 2017 7033-329B 9
3100 Millennium Wood Appliance
Figure 9.1
Figure 9.2
HIGH
MED
LOW
Burn Rate
Air Control
Start-Up
Air Control
Manual
Timer (ACC)
Shut Down
Pull Forward
to Shut Down
Figure 9.3
position
flow
air flow
Injury Risk.
• Gloves recommended
CAUTION
very important that the ames be maintained and not allowed
to go out. This will ensure the cleanest possible re. If the
ames tend to go out, it is set too low for your burning condi-
tions. The air control located at the upper right hand corner
is used to adjust for burn rates. This is called the Burn Rate
Air Control. Figure 9.1
3. Final Stage
The nal stage of burning is the charcoal stage. This occurs
when the ammable gases have been mostly burned and only
charcoal remains. This is a naturally clean portion of the burn.
The coals burn with hot blue ames.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of heat
needed to dry and rekindle the next load of wood. It is best
to open the Burn Rate Air and Start-Up Air Controls before
reloading. This livens up the coal bed and reduces excessive
emissions (opacity/smoke). Open door slowly so that ash or
smoke does not exit appliance through opening. You should
also break up any large chunks and distribute the coals so
that the new wood is laid on hot coals.
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To do
this we need to learn to burn our appliances in the cleanest
way possible. Doing this will allow us to continue using our
wood appliances for many years to come.
D. Air Controls
Users will need to nd their preferred setting between high and
low based on desired heat output, installation conguration,
and fuel type.
1. Burn Rate Air Control
This air supply enters at the upper front of the rebox, near
the top of the glass door. This preheated air supplies the nec-
essary fresh oxygen to mix with the unburned gases, helping
to create second, third and fourth combustions. This air is
regulated by the Burn Rate Air Control. When the control is
moved all the way up it is on the High setting and when moved
all the way down it is on the Low setting. Figure 9.1
2. Automatic Combustion Control System (ACC)
To engage the Automatic Combustion Control (ACC) timer
system push the lever towards the back of the appliance to
the “HI” position, then pull forwards towards the front of the
appliance until the knob stops. The timer will slowly close in
about 25 minutes. Use this feature when reloading fuel or if
you want more air supplied to the re. Figure 9.3
E. Using Burn Rate Air Control & ACC System
1. Start up and Reloading Fuel
Open both Burn Rate Air Control and ACC systems fully. To
do this with the Burn Rate Air Controls push spring handle
up to high. For the ACC timer system push knob towards
back of appliance until the knob is located under the high
position. Figure 9.1
2. Maximize Heat with The ACC System
To maximize heat output with the ACC timer System or
also known as high burn push the ACC Air Control lever
towards the back of the appliance and leave. This com-
bined with having the main burn rate control lever pushed
up will deliver the most amount of air needed to achieve the
highest amount of heat output. Figure 9.1
3. Manual Timer Over-Ride
If you need to shut the ACC system off before it goes through
the cycle of shutting itself off; 25 minutes, reach towards the
back of the appliance on the right side and pull the lever
towards the front of the appliance. Figure 9.2
10 7033-329B June 7, 2017
3100 Millennium Wood Appliance
Figure 10.1
High (Open)
Low (Closed)
Start-Up Air
Control
B
urn Rate
A
ir Control
Front Air Channel
Operated by Timer
Rear Air Channel
Operates independently
from Timer
HIGH
LOW
Timer
Timer Manual
Shut-off
Shown with Side
Shield Removed
After activating the timer (ACC), if the control is placed within
the rear air section on the label it will allow rear air to enter
the rebox. This will not interfere with the timer gradually
closing the front air channel in 25 minutes. If control is set
on “HI” it over-rides the timer (ACC).
F. Burn Rates and Operating Efciency
For maximum operating efciency
This wood appliance has a manufacturer-set minimum low
burn rate that must not be altered. It is against federal reg-
ulations to alter this setting or otherwise operate this wood
appliance in a manner inconsistent with operating instructions
in this manual.
• Burn dry, well-seasoned wood.
Burn Rates
1. Low burn setting:
• Burn Rate Air Control spring handle up to high position
for 5 minutes.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then pull
forwards towards the front of the appliance until the
knob stops (Figure 9.1 on page 9).
• At that point close the Burn Rate Air Control by moving
the spring handle to the low setting.
2. Medium low burn setting:
• Burn Rate Air Control spring handle up to high position
for 5 minutes.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then
pull forwards towards the front of the appliance until
the knob stops.
• At that point move the Burn Rate Air Control spring
handle to 1/8”-1/2” from the low setting.
3. Medium high burn setting:
• Burn Rate Air Control spring handle up to high position.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then
pull forwards towards the front of the appliance until
the knob stops.
• At that point move the Burn Rate Air Control spring
handle to 1/2” – high.
4. High burn setting:
• Burn Rate Air Control spring handle up to high position
• Also activate ACC timer system knob pushed back to
the “HI” position.
Note: If using the optional blower use burn settings 1-3
burn settings the blower shall be off for the rst 30 minutes
and then be operated in the high position at 30 minutes.
For high burn setting, blower may continue to be on full
after the loading of the fuel.
NOTE: The above information is provided as a guide-
line only. Altitude and other circumstances may require
control adjustments to achieve the desired burn rates.
NOTE: Operate appliance on High Burn 45 minutes a
day to help keep ue/chimney clean.
WARNING
Risk of Fire.
When set on High Burn Rate and over-riding the Auto-
matic Combustion Control system an over re situation
can occur and may result in a chimney re.
Over ring will void the appliance warranty.
June 7, 2017 7033-329B 11
3100 Millennium Wood Appliance
2 pc Baffle Board
Ceramic Blanket on Top
Tube Channels
Baffle Board even with front
tube & resting on all tubes
Burn Rate
Air Control
Start-Up
Air
Control
Figure 11.1
G. Building A Fire
Before lighting your rst re in the appliance:
1. Conrm the bafe is correctly positioned. It should be
even with the front tube and resting on all tubes (Figure
11.1 and 11.2).
2. Remove all labels from glass and inside of appliance.
There are many ways to build a re. The basic principle is
to light easily-ignitable tinder or paper, which ignites the fast
burning kindling, which in turn ignites the slow-burning re-
wood. Here is one method that works well:
1.
Open the Burn Rate Air and ACC Controls fully (Refer to
page 6 Start-Up Guide).
2. Place several wads of crushed paper on the rebox oor.
Heating the ue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles are in
the immediate area of the appliance. Be sure the room
is adequately ventilated and the ue unobstructed.
5. Light the paper in the appliance. NEVER light or rekindle
re with kerosene, gasoline, or charcoal lighter uid; the
results can be fatal.
6. Once the kindling is burning quickly, add several full-length
logs 3 inches (76mm) or 4 inches (102mm) in diameter.
Be careful not to smother the re. Stack the pieces of
wood carefully; near enough to keep each other hot, but
far enough away from each other to allow adequate air
ow between them.
7. Set the Burn Rate Air Control and activate the ACC timer
system.
8. When ready to reload, It is best to fully open both the Burn
Rate Air and Start-up Air Controls before reloading. This
livens up the coal bed and reduces excessive emissions
(opacity/smoke). Open door slowly so that ash or smoke
does not exit appliance through opening. Large logs burn
slowly, holding a re longer. Small logs burn fast and hot,
giving quick heat.
9.
As long as there are hot coals, repeating steps 6 through
8 will maintain a continuous re.
NOTE: The special high temperature paint that your appli-
ance is nished with will cure as your appliance heats.
You will notice an odor and perhaps see some vapor rise
from the appliance surface; this is normal. We recom-
mend that you open a window until the odor dissipates
and paint is cured.
Figure 11.2
NOTE:
• Build re on brick rebox oor.
• Do NOT use grates, andirons or other methods to support
fuel. It will adversely affect emissions.
WARNING
Fire Risk
Do NOT store wood:
• Closer than required clearances to combustibles to
appliance
• Within space required for loading or ash removal.
Do NOT operate appliance:
• With appliance door open.
• With ash removal system door open.
Fire Risk.
• Do NOT burn wet or green wood.
• Store wood in dry location.
• Stack wood so both ends are exposed to air.
Wet, unseasoned wood can cause accumulation of
creosote.
WARNING
12 7033-329B June 7, 2017
3100 Millennium Wood Appliance
INCORRECT POSITIONS
H. Correct Bafe & Blanket Placement
Ceramic Blanket and Bafe Board are NOT in
contact with the back of the rebox.
Ceramic Blanket is NOT in contact with the
back of the rebox and NOT even with the Baf-
e Board in the front.
Ceramic Blanket is bunched up at the back of the
rebox and NOT even with the Bafe Board in the
front.
Ceramic Blanket
Back of Firebox
Baffle Board
Figure 12.2
Figure 12.1
CORRECT POSITION
WARNING
Fire Risk
Firebox damage due to improper bafe place-
ment is not covered by warranty. Operate the
wood burning appliance with the bafe in the
correct position only.
Not doing so could result in:
• Reduced efciency
• Overheating the chimney
• Overheating the rear of the rebox
• Poor performance
Ensure correct bafe placement and replace bafe com-
ponents if damaged or missing.
Ceramic Blanket and Bafe Board MUST be in
contact with the back of the rebox and even
with each other in the front.
Ceramic Blanket
Back of Firebox
Baffle Board
Baffle Retainer Bracket
CAUTION
The bafe boards are FRAGILE. Use extreme caution when
loading rewood to prevent:
• Cracking, breaking or damaging the bafe boards
DO NOT operate the appliance without bafe boards
June 7, 2017 7033-329B 13
3100 Millennium Wood Appliance
I. Blower Operating Instructions
NOTE: If your Quadra-Fire wood appliance is equipped with
an optional blower, you should follow these guidelines:
1. Initial (cold) start-up and all Burn Settings
The blower can be plugged in and turned on right away.
The blower fan is turned on and off by a snap disc. When
your appliance has reached a certain temperature the
blower will turn on and when your appliance has cooled
down to a certain temperature it will turn off. Switch on
blower control must be set to auto for this feature to work.
2. The blower is equipped with a speed control. Adjust
the fan speed by turning the speed control clockwise to
“Low” or counterclockwise to “High”.
3. Snap Disc Location
If you nd the blower coming on and off at undesirable
temperatures, relocate the snap disc to another location
in the designated zone on the back of the appliance.
Figure 13.1 There is a manual over-ride switch to
deactivate the snap disc, if necessary.
J. Opacity (Smoke)
This is the measure of how cleanly your appliance is burn-
ing. Opacity is measured in percent; 100% opacity is when
an object is totally obscured by the smoke column from a
chimney, and 0% opacity means that no smoke column can
be seen. As you become familiar with your appliance, you
should periodically check the opacity. This will allow you to
know how to burn as nearly smoke-free as possible (goal of
0% opacity).
WARNING
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monoxide if burn material other than
wood.
May result in illness or possible death.
Fire Risk.
Keep combustible materials, gasoline and other
ammable vapors and liquids clear of appliance.
WARNING
• Do NOT store ammable materials in the appliance’s vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID OR SIMILAR LIQUIDS TO
START OR “FRESHEN UP” A FIRE IN THIS Appliance.
• Keep all such liquids well away from the appliance while it is
in use.
• Combustible materials may ignite.
When burning your rst re, you will experience smoke and
odor from the appliance resulting from the curing of paint and
burning off of any oils remaining from manufacturing.
OPEN WINDOWS DURING INITIAL BURN TO DISSIPATE
SMOKE AND ODORS!
• Odors may be irritating to sensitive individuals.
• Smoke detectors may activate.
CAUTION
Figure 13.1
Snap Disc Location
Figure 13.2
Snap Disc
Bracket
with
Magnet
Secure wires
with wire tie
MANUAL
FAN
AUTO
LOW
HIGH
OFF
MANUAL:
Over-rides
the Snap
Disc
AUTO: Fan
will turn
ON/OFF
Automatically
by the Snap
Disc
Controls
the Fan
Speed
14 7033-329B June 7, 2017
3100 Millennium Wood Appliance
Negative pressure results from the imbalance of air avail-
able for the appliance to operate properly. It can be strongest
in lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)
• Range hoods
• Combustion air requirements for furnaces, water
appliances and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air conditioning
• Imbalances of the HVAC air handling system
• Upper level air leaks such as:
- Recessed lighting
- Attic hatch
- Duct leaks
To minimize the effects of negative air pressure:
• Install the outside air kit with the intake facing prevailing
winds during the heating season
• Ensure adequate outdoor air for all combustion appliances
and exhaust equipment
• Ensure furnace and air conditioning return vents are not
located in the immediate vicinity of the appliance
• Avoid installing the appliance near doors, walkways or
small isolated spaces
• Recessed lighting should be a “sealed can” design
• Attic hatches weather stripped or sealed
• Attic mounted duct work and air handler joints and seams
taped or sealed
WARNING
Asphyxiation Risk.
• Negative pressure can cause spillage of combustion
fumes, soot and carbon monoxide.
• Appliance needs to draft properly for safety.
L. Negative PressureK. Clear Space
• Do NOT place combustible objects within 4 ft (1.2 m) of
the front of appliance. See Figure 14.1.
• Mantel - avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these
objects.
Figure 14.1
Maintain 4 ft (1.22m) clearance to
combustible in front of appliance
WARNING
DO NOT PLACE COMBUSTIBLE OBJECTS IN FRONT
OF THE APPLIANCE. High temperatures may ignite
clothing, furniture or draperies.
June 7, 2017 7033-329B 15
3100 Millennium Wood Appliance
ISSUES SOLUTIONS
Odor from appliance When rst operated, this appliance may release an odor for the rst several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Whirring sound If the optional blower has been installed, the blower produces a whirring sound which
increases in volume as the speed is increased.
CONTACT YOUR DEALER for additional information regarding operation and troubleshooting.
Visit www.quadrare.com to nd a dealer.
WARNING
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monoxide if burn material other than
wood.
May result in illness or possible death.
Fire Risk.
Keep combustible materials, gasoline and other
ammable vapors and liquids clear of appliance.
WARNING
• Do NOT store ammable materials in the appliance’s vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL, KEROSENE,
CHARCOAL LIGHTER FLUID OR SIMILAR LIQUIDS TO
START OR “FRESHEN UP” A FIRE IN THIS APPLIANCE.
• Keep all such liquids well away from the appliance while it is
in use.
• Combustible materials may ignite.
M. Frequently Asked Questions
16 7033-329B June 7, 2017
3100 Millennium Wood Appliance
Bafe & Blanket
Optional Blower
Chimney System
Firebrick & Ash Removal
Door & Glass Assemblies
Door Handle
Frequency
MONTHLY
or
After Every
Cord of Wood
Bafe and blanket placement is critical to
heat output, efciency and overall life of the
appliance. Make sure the bafe is pushed
all of the way to the back of the rebox and
the blanket is laying at. Inspect bafe for
cracks.
YEARLY
or
After Every
4 Cords of
Wood
Vacuum the blower impellers.
EVERY 2
MONTHS
or
After Every
4 Cords of
Wood
T
he chimney and chimney cap must be in-
spected for soot and creosote every two
months during the burn season or more
frequency if chimney exceeds or is under 14-
16 ft (4.3m-4.8m) measured from bottom of
appliance.
This will prevent pipe blockage, poor draft,
and chimney res.
Always burn dry wood to help prevent cap
blockage and creosote build-up.
WEEKLY
or
After Every
25 Loads of
Wood
WEEKLY
or
After Every
25 Loads of
Wood
Keep door and glass gasket in good shape
to maintain good burn times on a low burn
setting. To test: place a dollar bill between the
appliance and door and then shut the door. If
you can pull the dollar out, remove one wash-
er from door handle behind latch cam and try
again. If you can still pull it out, replace the
door gasket.
Check the glass frame for loose screws to
prevent air leakage. Check glass for cracks.
WEEKLY
or
After Every 25
Loads of Wood
Check the door latch for proper adjustment.
This is very important especially after the door
rope has formed to the appliance face.
Check door handle for smooth cam operation.
Task
Baffle
Blanket
Locknut
Door Cross Section
(example)
Latch Cam
Spacing
Washers
Square Key
Door Handle
Spring
Handle
Ashes must be cool before you can dispose
of the ashes in a non-combustible container.
Firebrick is designed to protect your rebox.
After ashes are removed, inspect the re-
brick and replace rebricks that are crum-
bling, cracked or broken.
A. Quick Reference Maintenance Guide
When properly maintained, your replace will give you
many years of trouble-free service. Contact your dealer to
answer questions regarding proper operation, troubleshoot-
ing and service for your appliance. Visit www.quadrare.
com to nd a dealer
CAUTION! Allow the appliance to completely cool
down before performing any cleaning or maintenance.
Start the rst inspection after the rst 2 months of use, or if
performance changes, and adjust your schedule according-
ly. Maintenance is required for safe operation and must be
performed to maintain your warranty.
These are generic drawings and may not represent your model.
3 Maintenance and Service
June 7, 2017 7033-329B 17
3100 Millennium Wood Appliance
CAUTION
• Do not use polishes with abrasives. It will scratch plated sur-
faces.
1. Creosote (Chimney) Cleaning
• Frequency: Every 2 months during heating season or
as recommended by a certied chimney sweep; more
frequently if chimney exceeds or is under 14-16 ft.
(measured from bottom of appliance)
• By: Certified Chimney Sweep
Remove all ash from the rebox and extinguish all hot embers
before disposal. Allow the appliance to cool completely.
Disconnect ue pipe or remove bafe and ceramic blanket
from appliance before cleaning chimney. Otherwise residue
can pile up on top of the bafe and ceramic blanket and
the appliance will not work properly. (See Bafe Removal
on page 21). Close the door tightly. The creosote or soot
should be removed with a brush specically designed for
the type of chimney in use. Clean out fallen ashes from the
rebox.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build creosote
deposits quicker, so it is important to check the chimney from
the top as well as from the bottom.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which combine
with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool chimney ue
of a newly-started or a slow-burning re. As a result, creosote
residue accumulates on the ue lining. When ignited, this
creosote creates an extremely hot re which may damage the
chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to determine
if a creosote or soot buildup has occurred. If creosote or soot
has accumulated, it should be removed to reduce the risk of a
chimney re.
B. General Maintenance
Fire Risk.
• Do not use chimney cleaners or ame colorants
in your appliance. Will corrode chimney pipe.
WARNING
WARNING
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and chimney once every
two months during heating season.
• Remove creosote to reduce risk of chimney re.
• Ignited creosote is extremely HOT.
4. Cleaning Plated Surfaces
• Frequency: Prior to first burn and then as desired
• By: Homeowner
4. Glass Cleaning
• Frequency: As desired
• By: Homeowner
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed by
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven
cleaner left on during the next ring can permanently stain
the glass and damage the nish on metal surfaces.
A portion of the combustion air entering the rebox is deected
down over the inside of the door glass. This air ow “washes”
the glass, helping to keep smoke from adhering to its surface.
When operated at a low burn rate, less air will be owing over
the glass and the smokey, relatively cool condition of a low
re will cause the glass to become coated.
Operating the appliance with the Burn Rate Air Control and
Start-Up Air Control all the way open for 30-45 minutes should
remove the built up coating.
CAUTION
• Do not use polishes with abrasives. It will scratch surfaces.
Fire Risk.
Disposal of Ashes
WARNING
• Ashes should be placed in metal container with tight tting lid.
• Do not place metal container on combustible surface.
• Ashes should be retained in closed container until all cinders
have thoroughly cooled.
3. Disposal of Ashes
• Frequency:
When ash is within 1-3/4 in. (44mm) of firebox
lip
• By: Homeowner
Ashes should be placed in a metal container with a tight
tting lid. The closed container of ashes should be placed
on a non-combustible oor or on the ground, well away
from all combustible materials, pending nal disposal. If
the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed
container until all cinders have thoroughly cooled.
Clean all the ngerprints and oils from plated surfaces
BEFORE ring the appliance for the rst time. If not cleaned
properly before lighting your rst re, the oils can cause
permanent markings on the plating.
After the plating is cured, the oils will not affect the nish and
little maintenance is required. Wipe clean as needed.
18 7033-329B June 7, 2017
3100 Millennium Wood Appliance
With proper installation, operation, and maintenance your wood appliance will provide years of trouble-free service. If you
do experience a problem, this troubleshooting guide will assist you or a qualied service person in the diagnosis of a prob-
lem and the corrective action to be taken.
Start Fire Problems Possible Cause Solution
Can not get re started
Excessive smoke or spillage
Burns too slowly
Not enough heat output
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange kindling &
wood for air movement.
Not enough air for re to ignite
Check for restricted termination cap
Check for blockage of outside air kit (if installed).
Check for ue blockage.
Pre-warm ue before starting re (refer to Building
a Fire Section).
Check for adequate vent height (refer to Chimney
Height Section).
Open window below the appliance towards the
wind.
Wood condition is too wet, too
large
Use dry, seasoned wood (refer to Seasoned Wood
Section).
Bed of coals not established
before adding wood
Start with paper & kindling to establish bed of
coals (refer to Building a Fire Section).
Flue blockage such as birds’
nests or leaves in termination
cap
Have chimney inspected for creosote and cleaned
by a certied chimney sweep.
Down draft or negative pressure
Competition with exhaust
devices
Do not use exhaust fans during start-up (refer to
Negative Pressure Section).
Open window below the appliance towards the
wind.
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mix in less seasoned wood after re is established
(refer to Wood Fuel Section).
Over drafting
Check for correct vent height; too much vertical
height creates over drafting.
Check location of vent termination (refer to
Chimney Termination Requirement Section).
4 Troubleshooting Guide
June 7, 2017 7033-329B 19
3100 Millennium Wood Appliance
A. Glass Replacement - Door Assembly
(Replace with 5mm ceramic glass only)
1. Ensure that the re is out and the appliance is cool to
the touch.
2. Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent injury.
3. Remove the door with the broken glass by lifting the door
up and off of the hinges.
4.
Lay door face down on a table or counter making sure
the handle hangs over the edge so the door lays at, on
a soft surface.
5. Remove the screws from each glass retainer and remove
the glass. (If screws are difcult to remove, soak with
penetrating oil rst).
6. Center the glass with edges evenly overlapping the
opening in the door, (i.e. same space top and bottom,
left and right sides).
7. Replace the glass retainers. Be careful not to cross
thread the screws.
8. Tighten each retainer just a few turns until each is se-
cured. Check again for centering of glass in door frame.
Continue to tighten each retainer alternately, a few turns
at a time, until the glass is secure. DO NOT OVER
TIGHTEN - can cause glass to break.
9. Replace the door on the appliance.
Quadra-Fire appliances are equipped with ceramic super
heat-resistant glass, which can only be broken by impact or
misuse.
Handle glass assembly with care.
When cleaning glass:
• Avoid striking, scratching or
slamming glass.
• Do NOT clean glass when hot.
• Do NOT use abrasive cleaners.
• Use a hard water deposit glass cleaner on white lm.
• Use commercial oven cleaner on heavier deposits.
• Remove all residue of oven cleaner or will permanently stain
glass on next ring. Refer to maintenance instructions.
Glass
Assembly
WARNING
Injury Risk.
• Use only glass specied in manual.
• DO NOT REPLACE with any other material.
Magnet
Spade
Connectors
Snap Disc
Figure 19.1
C. Snap Disc Replacement
1. Locate the snap disc bracket assembly at the bottom left
rear corner of the appliance.
2. A magnet holds the bracket to the appliance. Pull the
bracket down away from the appliance to expose the snap
disc.
3. Pull the snap disc and spade connectors up and out of
bracket as shown in Figure 20.1
4. Using a Phillips head screw driver, remove the 2 screws
from the snap disc and then remove the snap disc from
the spade connectors. Replace with new snap disc and
re-connect to spade connectors.
5. Push the snap disc and spade connectors back inside
bracket and re-attach the bracket to the appliance.
CAUTION!
5 Service Part Replacement
B. Firebrick Replacement
Replace the rebrick if they become crumbly and/or if there
is a 1/4 inch (6.35mm) gap between the bricks.
Inspect the rebrick after each ash removal.
The rebox is lined with high quality rebrick, which has
exceptional insulating properties. There is no need to use a
grate; simply build a re on the rebox oor. Do not operate
appliance without rebrick.
1. After the coals have completely cooled, remove all old
brick and ash from appliance and vacuum rebox.
2. Remove new brick set from box and lay out to diagram
shown.
3. Lay bottom bricks in appliance.
4. Install rear bricks on the top of the bottom bricks. Slide
top of bricks under clip on back of rebox wall and push
bottom of brick back.
5. Install side bricks. Slide top of brick under clips on side
of rebox and push the bottom of the brick until it is ush
with the side of the appliance.
20 7033-329B June 7, 2017
3100 Millennium Wood Appliance
E. Bafe Removal
1. Remove all ash from the rebox, and extinguish all hot
embers before disposal into a metal container.
2. The bafe board has 2 pieces. With the ceramic blanket
still in place, slide one bafe piece over the top of other one
and pull out top piece through the door opening and then
remove bottom bafe piece. Figure 20.2
3. Remove the ceramic blanket.
4. Re-install the bafe pieces one piece at a time. Be sure
the bafe boards are even with the front manifold tube and
is resting on all tubes. Figure 20.4.
5. To re-install the ceramic blanket, it is easier to fold it in
half rst. Place on top of bafe board, open up and atten
and smooth out the blanket. Re-check the bafe board for
correct positioning. Figure 20.3.
Figure 20.2 - Bafe
Figure 20.3 - Ceramic Blanket
Figure 20.1
D. Door Handle Assembly
Locknut
Door Cross Section
(example)
Latch Cam
Spacing
Washers
Square Key
Door Handle
Spring
Handle
2 inch (51mm) clearance
required from bend in door
handle rod to end of spring
handle.
Figure 20.4
2 pc Baffle Board
Ceramic Blanket on Top
Tube Channels
Baffle Board even with front
tube & resting on all tubes
Burn Rate
Air Control
Automatic
Combustion
Control
1. Install washer on door handle shaft.
2. Slide door handle through door.
3. Install second washer(s) as shown in Figure 20.1.
4. Install key in groove.
5. Align groove in latch cam with key; slide latch cam
over shaft
6. Install locknut but do not over tighten, the handle
needs to move smoothly.
7. Install spring handle turning in a counter-clockwise
motion to required 2 inch (51mm) clearance loca-
tion on door handle rod. Figure 20.1.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Quadrafire 3100 Millennium Le manuel du propriétaire

Marque
Quadrafire
Modèle
3100 Millennium
Catégorie
Cheminées
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents