Quadrafire 2100 Millennium Wood Stove Manuel utilisateur

Marque
Quadrafire
Modèle
2100 Millennium Wood Stove
Catégorie
Cheminées
Taper
Manuel utilisateur
1 7039-177C August 13, 2018
NOTICE: DO NOT DISCARD THIS MANUAL
2100 MILLENNIUM WOOD APPLIANCE
AUTOMATIC COMBUSTION CONTROL
(ACC)
MODEL:
21M-ACC
Owner’s Manual
Operation & Care
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
Contact your dealer with question on installation, operation, or service.
NOTE
To obtain a French translation of this manual, please
contact your dealer or visit www.quadrare.com
Pour obtenir une traduction française de ce manuel, s’il
vous plaît contacter votre revendeur ou visitez
www.quadrare.com
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
WARNING
Fire Risk.
For use with solid wood fuel only.
Other fuels may over-re and generate
poisonous gases (i.e. carbon monoxide).
WARNING
If the information in these instructions is
not followed exactly, a re could result
causing property damage, personal injury,
or death.
• Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any other
appliance.
• Do not over-re - If appliance or chimney connector
glows, you are over-ring. Over-ring will void your
warranty.
• Comply with all minimum clearances to combustibles
as specied. Failure to comply may cause house re.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
WARNING
Hot glass and appliance will cause burns.
• Do not touch glass until it is cooled
• Use leather gloves when reloading fuel
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures
• High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other
ammable materials away.
2 7039-177C August 13, 2018
2100 Millennium
Serial No.
Model
Name
Test Lab &
Report No.
Mfg. Date
SAMPLE
CONFIDENTIAL PROPERTY OF HEARTH & HOME TECHNOLOGIES INC.
PART NAME:
DRAWN BY:
SCALE:
MATERIAL:
SHEET:
PART NUMBER:
REV:
THIS PRINT IS CHECKED AND CONTROLLED BY THE ENGINEERING
DEPARTMENTS OF HEARTH & HOME TECHNOLOGIES INC.
ECO # DATE BYREV
UNLESS OTHERWISE SPECIFIED DIMS ARE INCHES[MM] & : TOLERANCES ARE: (2) PLACE DEC : ± 0.03 (3) PLACE DEC: ± 0.005 ANGLE: ± 2° FRACTION: ± 1/16
OUTSIDE MATERIAL. NORMAL DIM & INSIDE MATERIAL.
OUTSIDE APEX
INSIDE APEX - DIMS ENCLOSED BY AN OVAL ARE CRITICAL DIMENSIONS
REVISIONS
ITEM PART NUMBER PART NAME QTY
NOTE:
1. MATERIAL: NON-ANODIZED
ALUMINUM 0.020 THICK
2. BACKGROUND: SILVER
3. COPY: BLACK & RED
4. ADHESIVE: 3M #468 PERMANENT ACRYLIC
5. TEMPERATURE RATING: -50 F TO 350 F
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES. (UM) 84 HUD .
"For Use with Solid Wood Fuel Only"
352 Moutain House Road, Halifax, PA 17032
www.quadrafire.com
Install and use only in accordance with
manufacturer's installation and operating
instructions. Contact local building or fire officials
about restrictions and installation inspections in
your area. Do not obstruct the space beneath
heater.
For use with leg and pedestal options intended for
this model, refer to owner’s manual for appropriate
part numbers and installation instructions.
WARNING - For Mobile Homes: Do not install in
a sleeping room. An outside combustion air inlet
must be provided and unrestricted while unit is in
use. The structural integrity of the mobile home
floor, ceiling and walls must be maintained. The
stove needs to be properly grounded to the frame
of the mobile home. Components required for
mobile home installation: Outside Air Kit, Part
Number OAK-ACC.
Refer to manufacturer's instructions and local
codes for precautions required for passing
chimney through a combustible wall or ceiling and
maximum offsets.
Inspect and clean chimney frequently - Under
Certain Conditions of Use, Creosote Buildup May
Occur Rapidly.
Do not connect this unit to a chimney serving
another appliance.
Optional Blower, Part BK-ACC.
Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.
Route power cord away from unit. Do not route
cord under or in front of appliance.
DANGER: Risk of electrical shock. Disconnect
power supply before servicing.
Replace glass only with 5mm ceramic available
from your dealer.
Do not use grate or elevate fire. Build wood fire
directly on hearth.
Do not overfire - if heater or chimney connector
glows, you are overfiring.
Operate only with the fuel loading door closed.
Open only to add fuel to the fire.
CAUTION:
PREVENT HOUSE FIRES
FLOOR PROTECTION:
Floor protector must be a 3/8 (9.5mm) inch min.
thickness, non-combustible material or equivalent,
extending beneath heater and to front/sides/rear as
indicated on the diagram below. Exception:
Non-combustible floor protections must extend
beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each
side.
Report / Rapport
0061WS070S
TESTED TO:/ TESTÉ À:
UL 1482-11 (R2015), ULC S627-00.
Manufactured by:
Fabriqué par:
HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS. KEEP
FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS
G
H
R
7039-134_R11
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES
BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.
ATTENTION:
APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE
COMBUSTIBLE SOLIDE, POUR USAGE DANS LES
MAISONS MOBILES. (UM) 84-64 HUD. "Pour Usage
Avec Bois Solide Seulement"
Installez et utilisez en accord avec les instructions
d'installation et d'opération du fabricant. Contactez le bureau
de la construction ou le bureau des incendies au sujet des
restrictions et des inspections d'installation dans votre
voisinage. Ne pas obstruez l'espace en dessous de l'appareil.
AVIS - Pour Les Maisons Mobiles: Ne pas installer dans une
chambre à coucher. Un tuyau extérieur de combustion d'air
doit être installé et ne doit pas être obstrué lorsque l'appareil
est en usage. La structure intégrale du plancher, du plafond et
des murs de la maison mobile doit être maintenue intacte.
L'appareil de chauffage doit être fixé à la charpente de la
maison mobile. Les composants requis pour l'installation des
maisons mobiles: Assemblage d'air extérieur, Numéro de
Pièce OAK-ACC.
Référez vous aux instructions du fabricant et des codes
locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles, et les
compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Sous
certaines conditions, il se peut que la créosote s'accumule
rapidement.
Ne pas connecter cet appareil à une cheminée servant un
autre appareil.
Composants Optionnels: Ventilateur Optionnel, Pièce
BK-ACC.
Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil
électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique. Déconnectez
le fil électrique de la prise de contact avant le service.
Remplacez la vitre seulement avec une vitre céramique de 5
mm disponible chez votre fournisseur.
N'élevez pas le feu. Bâtissez le feu de bois directement sur
l'âtre.
Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau de
cheminée rougissent, vous surchauffez.
Opérez l'appareil seulement lorsque la porte de chargement
est fermée. Ouvrez la porte seulement lorsque vous devez
ajouter des combustibles dans le feu.
PRÉVENTION DES FEUX DE MAISON
PROTECTION DU PLANCHER
:
Le protecteur de plancher doit être d'un minimum de 3/8 inch
(9.5mm) d'épaisseur, de matériel incombustible ou
équivalent, s'étendant du dessous de l'appareil de chauffage
à l'avant, aux cotés et à l'arrière comme indiqué sur le
diagramme suivant. Exception: Les protections
incombustibles du plancher doivent s'étendre en dessous du
conduit de cheminée lorsqu'installées avec une ventilation à
l'horizontale et s'étendre de 2 inches (51mm) de chaque
côté.
STOVE TO CEILING CLEARANCE
ESPACE LIBRE DU POÊLE AU
PLAFOND
C
D
ALCOVE TOP VIEW /
VUE DU HAUT DE L'ALCÔVE
G
A
B
ALCOVE SIDE VIEW /
VUE DE CÔTÉ DE L'ALCÔVE
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
16" from glass
8 in.
USA
Fuel loading door
5-3/4 in.
2-1/4 in."
29-5/8 in.
minimum
39 in.
minimum
CANADA
203mm (8 in.)
203mm
(8 in.)
203mm
(8 in
.)
457mm (18 in.)
1245mm
(49 in.)
minimum
1006mm (39-5/8 in.)
minimum
O-T L
Tested and
Listed by
Portland
Oregon USA
OMNI-Test Laboratories, Inc.
C
US
Made in U.S.A. of US and
imported parts.
Fabriqué aux
États-Unis-d’Amérique par des
pièces d’origine américaine et
pièces importées.
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2015 particulate emission standards at 2.1 g/hr
EPA method 28 and 5G. Not approved for sale after May 15, 2020.
2017
2018
2019 JAN FEB MAR APR MAY JUN
JUL AUG SEP OCT NOV DEC
This wood heater needs periodic inspection and repair for proper operation. Consult the owner’s manual for further information. It is against
federal regulations to operate this wood heater in a manner inconsistent with the operating instructions in the owner’s manual.
21 MILLENIUM
DISCOVERY I
2100 ACC Series
A B C D E F G H
SINGLE WALL PIPE 15 (381) 11 (279) 21.5 (546) 13 (330) 8.5 (216) 17 (432) 56 (1422) N/A
CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE 8.75 (222) 5.75 (146) 20 (508) 10.5 (267) 7.5 (191) 16 (406) 43 (1092) N/A
CONDUIT DU MUR SIMPLE
INSTALLATION:
HORIZONTAL WITH
MINIMUM
2 FT VERTICAL OFF STOVE TOP
INSTALLATION:
HORIZONTALE AVEC 609mm VERTICAL
MINIMUM
DU HAUT DU POÊLE
SINGLE WALL PIPE 14 (356) 10 (254) 20.5 (521) 12 (305) 8.5 (216) 17 (432) 56 (1422) 9.5 (241)
CONDUIT DU MUR SIMPLE
DOUBLE WALL PIPE 9.5 (241) 5.5 (140) 21.5 (546) 13 (330) 7.5 (191) 16 (406) 43 (1092) 5 (127)
CONDUIT DU MUR SIMPLE
INSTALLATION: ALCOVE -
Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL 103 HT listed factory-built
Class "A" chimney, or a masonry chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48
inches (1220mm) with a minimum height of 43 inches (1092mm) to top of unit, and the referenced clearances.
INSTALLATION: ALCÔVE -
De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine 103HT de
Classe "A", ou une
cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une
hauteur minimum de 43 inches (1092mm) du haut de l'appareil, et des espaces libres alloués.
DOUBLE WALL PIPE 9.5 (241) 5.5 (140) 21.5 (546) 13.5 (343) N/A N/A 43 (1092) 5 (127)
CONDUIT DU MUR DOUBLE
E
F
E
F
CORNER INSTALLATION
INSTALLATION DU COIN
BACKWALL/SIDEWALL
MUR ARRIÈRE/MUR DE CÔTÉ
A
B
C
D
SPÉCIFICATIONS DE LA VENTILATION:
MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de
minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en
usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides,
ou une cheminée de briques, avec espaces libres référés.
MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit
d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe
"A, ou une cheminée de briques, avec espaces libres alloués.
*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650 degré C cheminée
bâtit en usine.
MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk
Metalbestos DS ou Security DL. Doit êttre équipé d'un arrêt d'étincelle. Utiliser les
espaces libres pour mur double comme mentionné ci-bas.
ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES En Pouces &
(millimètres)
NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur
de l'entrée du conduit.
VENT SPECIFICATIONS:
SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or
blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney,
suitable for use with solid fuels, or a masonry chimney, and the referenced clearances.
DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air
insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a
masonry chimney and the referenced clearances
*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650 degree
Factory-built chimneys.
MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or
Security DL double wall connector pipe. Must be equipped with a spark arrestor.
Apply double wall clearances below when installing unit.
MINIMUM CLEARANCES TO COMBUSTIBLES In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.
INSTALLATION: FULL VERTICAL / ENTIÈREMENT VERTICALE
Serial No. / N° de série
HF
BARCODE LABEL
A. Sample of Serial Number / Safety Label
LOCATION: Back of appliance
NOTE: Clearances may only be reduced by means approved
by the regulatory authority having jurisdiction
August 13, 2018 7039-177C 3
2100 Millennium
TABLE OF CONTENTS
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
Quadra-Fire is a registered trademark of Hearth & Home Technologies.
A. Sample of Serial Number / Safety Label ........ 2
B. Warranty Policy ............................ 4
C. Quick Start Guide .......................... 7
1 Listing and Code Approvals ..............8
A. Appliance Certication ...................... 8
B. BTU & Efciency Specications ............... 8
C. Glass Specications ........................ 9
D. Mobile Home Approved...................... 9
E. Sleeping Room ............................ 9
F. California - Prop65 .......................... 9
2 Operating Instructions .....................10
A. Over-Firing Your Appliance .................. 10
B. Wood Selection & Storage ..................10
C. Burning Process .......................... 10
D. Air Controls .............................. 11
E. Using Burn Rate Air Control & ACC System ..... 11
F. Burn Rates and Operating Efciency .......... 12
G. Building A Fire ........................... 13
H. Correct Bafe & Blanket Placement ........... 14
I. Blower Operating Instructions ................ 15
J. Opacity (Smoke) .......................... 15
K. Clear Space.............................. 16
L. Negative Pressure ......................... 16
M. Frequently Asked Questions................. 17
3 Maintenance and Service .................18
A. Quick Reference Maintenance Guide .......... 18
B. General Maintenance ...................... 19
4 Troubleshooting Guide .....................21
5 Service Part Replacement ................22
A. Glass Replacement - Door Assembly .......... 22
B. Firebrick Replacement .....................22
C. Snap Disc Replacement .................... 22
D. Door Handle Assembly ..................... 23
E. Bafe Removal ...........................23
F. Tube Channel Assembly Replacement ......... 24
6 Reference Materials ..........................25
A. Service and Maintenance Log................ 25
B. Exploded View............................ 26
C. Service Parts............................. 27
D. Accessories ..............................29
4 7039-177C August 13, 2018
2100 Millennium
4021-645J • 08-03-171
Hearth & Home Technologies
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies, on behalf of its hearth brands (“HHT”), extends the following warranty for HHT gas, wood, pellet and
electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
WARRANTY PERIOD:
distributor, whichever occurs earlier. However, the warranty shall commence no later than 24 months following the date of product
is produced in the following table.
Parts Labor Gas Pellet Wood Electric Venting Components Covered
X X
Igniters, auger motors, electronic components, and
glass
X X X
Factory-installed blowers
X
Molded refractory panels
X
Ignition Modules
X
Firepots, burnpots, mechanical feeders/auger
assemblies
X
Vent Free burners, Vent Free ceramic fiber logs,
Aluminized Burners
X X
Castings and Baffles
6 years 3 years
X
Catalyst - limitations listed
7 years 3 years
X X
Manifold tubes, HHT chimney and termination
10 years 1 year
X
Burners, logs and refractory
Limited
Lifetime
3 years
X X X
Firebox and heat exchanger, Grate and Stainless
Steel Burners, FlexBurn® System (engine, inner
cover,access cover and fireback)
X X X X X
All replacement parts beyond warranty period
Warranty Period HHT Manufactured Appliances and Venting
All parts and material except as covered by
Conditions, Exclusions, and Limitations listed
X X X
2 years
3 years
1 Year
90 Days
5 years 1 year
xX
B. Warranty Policy
August 13, 2018 7039-177C 5
2100 Millennium
4021-645J • 08-03-172
WARRANTY CONDITIONS:
• This warranty only covers HHT appliances that are purchased through an HHT authorized dealer or distributor. A list of HHT
authorized dealers is available on the HHT branded websites.
•
• This warranty is only valid in the country in which the HHT authorized dealer or distributor that sold the appliance resides.
• Contact your installing dealer for warranty service. If the installing dealer or distributor is unable to provide necessary parts, contact
other than the dealer from whom you originally purchased the product.
• Check with your dealer in advance for any costs to you when arranging a warranty call. Travel and shipping charges for parts are not
covered by this warranty.
• Limited Catalyst Warranty
o For wood burning products containing a catalyst, the catalyst will be warranted for a six-year period as follows: if the original
o From 37 to 72 months a pro-rated credit will be allowed against a replacement catalyst and labor credit necessary to install
Amount of Time Since Purchase Credit Towards Replacement Cost
0 - 36 Months 100%
37 - 48 Months 30%
49 - 60 Months 20%
61 - 72 Months 10%
o Any replacement catalyst will be warranted under the terms of the catalyst warranty for the remaining term of the original
WARRANTY EXCLUSIONS:
This warranty does not cover the following:
•
•
• Repair or replacement of parts that are subject to normal wear and tear during the warranty period are not covered. These parts
•
this noise are not covered by this warranty.
•
•
•
•
6 7039-177C August 13, 2018
2100 Millennium
4021-645J • 08-03-173
This warranty is void if:
•
•
• There is any damage to the appliance or other components due to water or weather damage which is the result of, but not limited
LIMITATIONS OF LIABILITY
•
have other rights, which vary from state to state. EXCEPT TO THE EXTENT PROVIDED BY LAW, HHT MAKES NO EXPRESS WARRANTIES
OTHER THAN THE WARRANTY SPECIFIED HEREIN. THE DURATION OF ANY IMPLIED WARRANTY IS LIMITED TO DURATION OF THE
EXPRESSED WARRANTY SPECIFIED ABOVE.
August 13, 2018 7039-177C 7
2100 Millennium
C. Quick Start Guide
ITEMS NEEDED FOR FIRST FIRE:
10 Pieces of Newspaper, 10-20 Pieces of Dry Kindling
and a Few Pieces of Dry Split Wood.
Note: These are generic drawings and may not represent your specific model.
OPEN AIR
CONTROLS
1 2 3
LOAD WOOD ADD NEWSPAPER
4
5
6 7
ADD KINDLING
WARNING! Risk of Fire
Close and securely latch the door after
the fire has started, and after refueling, to
prevent:
-Spillage of smoke, flame and carbon
monoxide
-Spillage of sparks, coals, and logs
-Over firing
DO NOT leave the appliance unattended
with the door open.
Starting a fire may not require an open
door for draft. The air control should
supply adequate draft.
ADD MORE WOOD
REDUCE AIR
CONTROLS
Ser to desired heat output.
The appliance is ready
for normal operation.
HIGH
BURN RA
TE
CONTROL
(Upper Right
Corner)
AUTOMATIC
COMBUSTION
CONTROL (ACC)
(Middle right hand side)
HIGH
LIGHT THE PAPER
LOW
BURN RATE
CONTROL
(Upper Right
Corner)
AUTOMATIC
COMBUSTION
CONTROL (ACC)
(Middle right hand side)
LOW
8 7039-177C August 13, 2018
2100 Millennium
The Quadra-Fire 2100 Millennium Wood Appliance (ACC) meets the U.S. Environmental Protection Agency’s crib wood
emission limits for wood appliances sold after May 15, 2015.
This wood appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate
this wood appliance in a manner inconsistent with operating instructions in this manual.
A. Appliance Certication B. BTU & Efciency Specications
NOTE: This installation must conform with local codes. In the absence of local codes you must comply with (UM) 84-
HUD and NFPA211 in the U.S.A. and CAN/CSA-B365 Installation Codes in Canada.
1 Listing and Code Approvals
Model: 2100 Millennium Wood Appliance
Laboratory: OMNI Test Laboratories, Inc.
Report No & Date: 0061WS070S
Type:
Listed Room Appliance, Solid Fuel
Type
Standard:
UL1482-11 (R2015) and ULC
S627-00 and (UM) 84-HUD, Mobile
Home Approved.
EPA Certication #: 664
EPA Certied Emissions: 2.1 grams per hour
*LHV Tested Efciency: 78.7%
**HHV Tested Efciency: 72.9 %
***EPA BTU Output: 12,000 to 28,800 / hr.
****Peak BTU/Hour
Output:
44,000
Vent Size: 6 inches
Firebox Size: 1.48 cubic feet
Recommended Wood
Length:
16 inches
Fuel Orientation: Front-to-Back
Fuel Seasoned Cord Wood
*Weighted average LHV (Low Heating Value) efciency
using Douglas Fir dimensional lumber and data collected
during EPA emission test. LHV assumes the moisture is
already in a vapor state so there is no loss in energy to
vaporize.
**Weighted average HHV (High Heating Value) efciency
using Douglas Fir dimensional lumber and data collected
during EPA emission test. HHV includes the energy
required to vaporize the water in the fuel.
***A range of BTU outputs based on EPA Default
Efciency and the burn rates from the low and high EPA
tests, using Douglas Fir dimensional lumber.
****A peak BTU out of the appliance calculated using the
maximum rst hour burn rate from the High EPA Test and
the BTU content of cord wood (8600) times the efciency.
August 13, 2018 7039-177C 9
2100 Millennium
E. Sleeping Room
F. California - Prop65
WARNING
This product and the fuels used to operate this product (wood), and
the products of combustion of such fuels, can expose you to
chemicals including carbon black, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to
the State of California to cause birth defects or other reproductive
harm. For more information go to: WWW.P65Warnings.ca.gov
When installed in a sleeping room it is recommended that
a smoke and/or CO alarm be installed in the bedroom. The
size of the room must be at least 50ft³ per 1,000 Btu/hr
stove input, if the stove exceeds the room size, out air must
be installed.
NOTE: Hearth & Home Technologies, manufacturer of this
appliance, reserves the right to alter its products,
their specications and/or price without notice.
D. Mobile Home Approved
• This appliance is approved for mobile home
installations when not installed in a sleeping room and
when an outside combustion air inlet is provided.
• The structural integrity of the mobile home oor, ceiling,
and walls must be maintained.
• The appliance must be properly grounded to the
frame of the mobile home with #8 copper ground wire,
and chimney must be listed to UL103 HT or a listed
UL-1777 full length six inch (152mm) diameter liner
must be used.
• Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
C. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please
contact your dealer for replacement glass.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Operating appliance without legs attached (if supplied
with appliance).
• Do NOT Over re - If appliance or chimney connector
glows, you are over ring.
Any such action that may cause a re hazard.
10 7039-177C August 13, 2018
2100 Millennium
User Guide
2 Operating Instructions
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover,
out of the rain and snow. Dry and well-seasoned wood will
not only minimize the chance of creosote formation, but will
give you the most efcient re. Even dry wood contains at
least 15% moisture by weight, and should be burned hot
enough to keep the chimney hot for as long as it takes to
dry the wood out - about one hour. It is a waste of energy to
burn unseasoned wood of any kind.
1. Symptoms of Over-Firing
Symptoms of over-ring may include one or more of the
following:
• Chimney connector or appliance glowing
• Roaring, rumbling noises
• Loud cracking or banging sounds
• Metal warping
• Chimney re
2. What To Do if Your Appliance is Over-Firing
• Immediately close the door and air controls to reduce
air supply to the re.
• If you suspect a chimney re, call the re department
and evacuate your house.
• Contact your local chimney professional and have
your appliance and appliance pipe inspected for any
damage.
• Do not use your appliance until the chimney
professional informs you it is safe to do so.
Hearth & Home Technologies WILL NOT warranty
appliances that exhibit evidence of over-ring. Evidence of
over-ring includes, but is not limited to:
• Warped air tube
• Deteriorated refractory brick retainers
• Deteriorated bafe and other interior components
A. Over-Firing Your Appliance
C. Burning Process
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order
to improve the situation, we at Quadra-Fire have developed
cleaner-burning wood appliances that surpass the
requirements for emissions established by our governing
agencies. These wood appliances, like any other
appliances, must be properly operated in order to insure
that they perform the way they are designed to perform.
Improper operation can turn most any wood appliance into
a smoldering environmental hazard.
1. Kindling or First Stage
It helps to know a little about the actual process of burning
in order to understand what goes on inside a appliance.
The rst stage of burning is called the kindling stage. In
this stage, the wood is heated to a temperature high
enough to evaporate the moisture which is present in
all wood. The wood will reach the boiling point of water
(212°F) and will not get any hotter until the water is
evaporated. This process takes heat from the coals and
tends to cool the appliance.
Fire requires three things to burn - fuel, air and heat. So, if
heat is robbed from the appliance during the drying stage,
the new load of wood has reduced the chances for a good
clean burn. For this reason, it is always best to burn dry,
seasoned rewood. When the wood isn’t dry, you must
open the air controls and burn at a high burn setting for a
longer time to start it burning. The heat generated from the
re should be warming your home and establishing the ue
draft, not evaporating the moisture out of wet, unseasoned
wood, resulting in wasted heat.
Fire Risk.
Do not over-re.
Over-ring may ignite creosote or will damage the
appliance and chimney.
WARNING
To prevent over-ring your appliance, DO NOT:
• Use ammable liquids
• Overload with wood
• Burn trash or large amounts of scrap lumber
• Permit too much air to the re
Dead wood lying on the forest oor should be considered
wet, and requires full seasoning time. Standing dead wood
can be considered to be about 2/3 seasoned. To tell if
wood is dry enough to burn, check the ends of the logs. If
there are cracks radiating in all directions from the center,
it is dry. If your wood sizzles in the re, even though the
surface is dry, it may not be fully cured.
Splitting wood before it is stored reduces drying time.
Wood should be stacked so that both ends of each piece
are exposed to air, since more drying occurs through the
cut ends than the sides. This is true even with wood that
has been split. Store wood under cover, such as in a shed,
or covered with a tarp, plastic, tar paper, sheets of scrap
plywood, etc., as uncovered wood can absorb water from
rain or snow, delaying the seasoning process.
Visit www.quadrare.com/shopping-tools/videos to view
product and use & care videos.
August 13, 2018 7039-177C 11
2100 Millennium
Figure 11.1
Figure 11.2
HIGH
MED
LOW
Burn Rate
Air Control
Start-Up
Air Control
Manual
Timer (ACC)
Shut Down
Pull Forward
to Shut Down
Figure 11.3
D. Air Controls
Users will need to nd their preferred setting between
high and low based on desired heat output, installation
conguration, and fuel type.
1. Burn Rate Air Control
This air supply enters at the upper front of the rebox, near
the top of the glass door. This preheated air supplies the
necessary fresh oxygen to mix with the unburned gases,
helping to create second, third and fourth combustions.
This air is regulated by the Burn Rate Air Control. When
the control is moved all the way up it is on the High setting
and when moved all the way down it is on the Low setting
(Figure 11.1).
2. Automatic Combustion Control System (ACC)
To engage the Automatic Combustion Control (ACC) timer
system push the lever towards the back of the appliance to
the “HI” position, then pull forwards towards the front of the
appliance until the knob stops. The timer will slowly close in
about 25 minutes. Use this feature when reloading fuel or if
you want more air supplied to the re (Figure 11.3).
E. Using Burn Rate Air Control & ACC System
1. Start up and Reloading Fuel
Open both Burn Rate Air Control and ACC systems fully. To
do this with the Burn Rate Air Controls push spring handle
up to high. For the ACC timer system push knob towards
back of appliance until the knob is located under the high
position (Figure 11.1).
2. Maximize Heat with The ACC System
To maximize heat output with the ACC timer System or also
known as high burn push the ACC Air Control lever towards
the back of the appliance and leave. This combined with
having the main burn rate control lever pushed up will
deliver the most amount of air needed to achieve the
highest amount of heat output (Figure 11.1).
3. Manual Timer Over-Ride
If you need to shut the ACC system off before it goes
through the cycle of shutting itself off; 25 minutes, reach
towards the back of the appliance on the right side and pull
the lever towards the front of the appliance (Figure 11.2).
Injury Risk.
• Gloves recommended
CAUTION
2. Second Stage
The next stage of burning, the secondary stage, is the
period when the wood gives off ammable gases which
burn above the fuel with bright ames. During this stage of
burning it is very important that the ames be maintained
and not allowed to go out. This will ensure the cleanest
possible re. If the ames tend to go out, it is set too low for
your burning conditions. The air control located at the upper
right hand corner is used to adjust for burn rates. This is
called the Burn Rate Air Control (Figure 11.1).
3. Final Stage
The nal stage of burning is the charcoal stage. This occurs
when the ammable gases have been mostly burned and
only charcoal remains. This is a naturally clean portion of
the burn. The coals burn with hot blue ames.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of
heat needed to dry and rekindle the next load of wood. It
is best to open the Burn Rate Air and Start-Up Air Controls
before reloading. This livens up the coal bed and reduces
excessive emissions (opacity/smoke). Open door slowly so
that ash or smoke does not exit appliance through opening.
You should also break up any large chunks and distribute
the coals so that the new wood is laid on hot coals.
Air quality is important to all of us, and if we choose to
use wood to heat our homes we should do so responsibly.
To do this we need to learn to burn our appliances in the
cleanest way possible. Doing this will allow us to continue
using our wood appliances for many years to come.
12 7039-177C August 13, 2018
2100 Millennium
Figure 12.1
High (Open)
Low (Closed)
Start-Up Air
Control
B
urn Rate
A
ir Control
Front Air Channel
Operated by Timer
RearAir Channel
Operates independently
from Timer
HIGH
LOW
Timer
Timer Manual
Shut-off
Shown with Side
Shield Removed
After activating the timer (ACC), if the control is placed
within the rear air section on the label it will allow rear air
to enter the rebox. This will not interfere with the timer
gradually closing the front air channel in 25 minutes. If
control is set on “HI” it over-rides the timer (ACC).
F. Burn Rates and Operating Efciency
For maximum operating efciency
This wood appliance has a manufacturer-set minimum
low burn rate that must not be altered. It is against federal
regulations to alter this setting or otherwise operate this
wood appliance in a manner inconsistent with operating
instructions in this manual.
• Burn dry, well-seasoned wood.
Burn Rates
1. Low burn setting:
• Burn Rate Air Control spring handle up to high
position for 5 minutes.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then
pull forwards towards the front of the appliance
until the knob stops (Figure 9.1 on page 9).
• At that point close the Burn Rate Air Control by
moving the spring handle to the low setting.
2. Medium low burn setting:
• Burn Rate Air Control spring handle up to high
position for 5 minutes.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then
pull forwards towards the front of the appliance
until the knob stops.
• At that point move the Burn Rate Air Control spring
handle to 1/8”-1/2” from the low setting.
3. Medium high burn setting:
• Burn Rate Air Control spring handle up to high
position.
• Then activate the ACC timer system by pushing the
knob all the back toward the appliance to “HI” then
pull forwards towards the front of the appliance
until the knob stops.
• At that point move the Burn Rate Air Control spring
handle to 1/2” – high.
4. High burn setting:
• Burn Rate Air Control spring handle up to high
position
• Also activate ACC timer system knob pushed back
to the “HI” position.
NOTE: The above information is provided as a guideline
only. Altitude and other circumstances may
require control adjustments to achieve the
desired burn rates.
NOTE: Operate appliance on High Burn 45 minutes a day
to help keep ue/chimney clean.
WARNING
Risk of Fire.
When set on High Burn Rate and over-riding the
Automatic Combustion Control system an over re
situation can occur and may result in a chimney
re.
Over ring will void the appliance warranty.
NOTE: If using the optional blower use burn settings 1-3
burn settings the blower shall be off for the rst 30
minutes and then be operated in the high position
at 30 minutes. For high burn setting, blower may
continue to be on full after the loading of the fuel.
August 13, 2018 7039-177C 13
2100 Millennium
2 pc Baffle Board
Ceramic Blanket on Top
Tube Channels
Baffle Board even with front
tube & resting on all tubes
Burn Rate
Air Control
Start-Up
Air
Control
Figure 13.1
G. Building A Fire
Before lighting your rst re in the appliance:
NOTE: The special high temperature paint that your
appliance is nished with will cure as your
appliance heats. You will notice an odor and
perhaps see some vapor rise from the appliance
surface; this is normal. We recommend that you
open a window until the odor dissipates and paint
is cured.
Figure 13.2
1. Conrm the bafe is correctly positioned. It should
be even with the front tube and resting on all tubes
(Figure 13.1 and 13.2).
2. Remove all labels from glass and inside of appliance.
There are many ways to build a re. The basic principle is
to light easily-ignitable tinder or paper, which ignites the
fast burning kindling, which in turn ignites the slow-burning
rewood. Here is one method that works well:
1. Open the Burn Rate Air and ACC Controls fully (Refer to
page 6 Start-Up Guide).
2. Place several wads of crushed paper on the rebox
oor. Heating the ue with slightly crumpled newspaper
before adding kindling keeps smoke to a minimum.
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles
are in the immediate area of the appliance. Be
sure the room is adequately ventilated and the ue
unobstructed.
5. Light the paper in the appliance. NEVER light or
rekindle re with kerosene, gasoline, or charcoal lighter
uid; the results can be fatal.
6. Once the kindling is burning quickly, add several full-
length logs 3 inches (76mm) or 4 inches (102mm) in
diameter. Be careful not to smother the re. Stack the
pieces of wood carefully; near enough to keep each
other hot, but far enough away from each other to allow
adequate air ow between them.
7. Set the Burn Rate Air Control and activate the ACC
timer system.
8. When ready to reload, It is best to fully open both
the Burn Rate Air and Start-up Air Controls before
reloading. This livens up the coal bed and reduces
excessive emissions (opacity/smoke). Open door
slowly so that ash or smoke does not exit appliance
through opening. Large logs burn slowly, holding a re
longer. Small logs burn fast and hot, giving quick heat.
9. As long as there are hot coals, repeating steps 6
through 8 will maintain a continuous re.
NOTE:
• Build re on brick rebox oor.
• Do NOT use grates, andirons or other methods to
support fuel. It will adversely affect emissions.
WARNING
Fire Risk.
Do NOT store wood:
• Closer than required clearances to
combustibles to appliance
• Within space required for loading or ash
removal.
Do NOT operate appliance:
• With appliance door open.
• With ash removal system door open.
Fire Risk.
• Do NOT burn wet or green wood.
• Store wood in dry location.
• Stack wood so both ends are exposed to air.
Wet, unseasoned wood can cause accumulation
of creosote.
WARNING
Fire Risk.
• Do not leave the re unattended when the
door is unlatched or when using the re
screen.
• Unstable rewood could fall out of the rebox
creating a re hazard to your home.
WARNING
14 7039-177C August 13, 2018
2100 Millennium
INCORRECT POSITIONS
H. Correct Bafe & Blanket Placement
Ceramic Blanket and Bafe Board are NOT in contact
with the back of the rebox.
Ceramic Blanket is NOT in contact with the back of the
rebox and NOT even with the Bafe Board in the front.
Ceramic Blanket is bunched up at the back of the rebox
and NOT even with the Bafe Board in the front.
Ceramic Blanket
Back of Firebox
Baffle Board
Figure 14.2
Figure 14.1
CORRECT POSITION
Ceramic Blanket and Bafe Board MUST be in contact
with the back of the rebox and even with each other in
the front.
Ceramic Blanket
Back of Firebox
Baffle Board
Baffle Retainer Bracket
The bafe boards are FRAGILE. Use extreme caution
when loading rewood to prevent:
• Cracking, breaking or damaging the bafe boards
DO NOT operate the appliance without bafe boards
CAUTION
WARNING
Fire Risk.
Firebox damage due to improper bafe
placement is not covered by warranty. Operate
the wood burning appliance with the bafe in
the correct position only.
Not doing so could result in:
• Reduced efciency
• Overheating the chimney
• Overheating the rear of the rebox
• Poor performance
Ensure correct bafe placement and replace
bafe components if damaged or missing.
August 13, 2018 7039-177C 15
2100 Millennium
I. Blower Operating Instructions
NOTE: If your Quadra-Fire wood appliance is equipped
with an optional blower, you should follow these
guidelines:
1. Initial (cold) start-up and all Burn Settings
The blower can be plugged in and turned on right
away. The blower fan is turned on and off by a snap
disc. When your appliance has reached a certain
temperature the blower will turn on and when your
appliance has cooled down to a certain temperature
it will turn off. Switch on blower control must be set to
auto for this feature to work.
2. The blower is equipped with a speed control. Adjust
the fan speed by turning the speed control clockwise to
“Low” or counterclockwise to “High” (Figure 15.2).
3. Snap Disc Location
If you nd the blower coming on and off at undesirable
temperatures, relocate the snap disc to another
location in the designated zone on the back of the
appliance (Figure 15.1). There is a manual over-ride
switch to deactivate the snap disc, if necessary.
J. Opacity (Smoke)
This is the measure of how cleanly your appliance is
burning. Opacity is measured in percent; 100% opacity is
when an object is totally obscured by the smoke column
from a chimney, and 0% opacity means that no smoke
column can be seen. As you become familiar with your
appliance, you should periodically check the opacity. This
will allow you to know how to burn as nearly smoke-free as
possible (goal of 0% opacity).
Figure 15.1
Snap Disc Location
Figure 15.2
Snap Disc
Bracket
with
Magnet
Secure wires
with wire tie
MANUAL
FAN
AUTO
LOW
HIGH
OFF
MANUAL:
Over-rides
the Snap
Disc
AUTO: Fan
will turn
ON/OFF
Automatically
by the Snap
Disc
Controls
the Fan
Speed
When burning your rst re, you will experience smoke
and odor from the appliance resulting from the curing
of paint and burning off of any oils remaining from
manufacturing.
OPEN WINDOWS DURING INITIAL BURN TO
DISSIPATE SMOKE AND ODORS!
• Odors may be irritating to sensitive individuals.
• Smoke detectors may activate.
CAUTION
Fire Risk.
Keep combustible materials, gasoline and other
ammable vapors and liquids clear of appliance.
• Do NOT store ammable materials in the
appliance’s vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID
OR SIMILAR LIQUIDS TO START OR
“FRESHEN UP” A FIRE IN THIS Appliance.
• Keep all such liquids well away from the
appliance while it is in use.
• Combustible materials may ignite.
WARNING
WARNING
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
• Do NOT burn treated wood or wood with salt
(driftwood).
• May generate carbon monoxide if burn
material other than wood.
May result in illness or possible death.
16 7039-177C August 13, 2018
2100 Millennium
Negative pressure results from the imbalance of air available
for the appliance to operate properly. It can be strongest in
lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)
• Range hoods
• Combustion air requirements for furnaces, water
appliances and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air
conditioning
• Imbalances of the HVAC air handling system
• Upper level air leaks such as:
- Recessed lighting
- Attic hatch
- Duct leaks
To minimize the effects of negative air pressure:
• Install the outside air kit with the intake facing prevailing
winds during the heating season
• Ensure adequate outdoor air for all combustion
appliances and exhaust equipment
• Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appliance
• Avoid installing the appliance near doors, walkways or
small isolated spaces
• Recessed lighting should be a “sealed can” design
• Attic hatches weather stripped or sealed
• Attic mounted duct work and air handler joints and
seams taped or sealed
WARNING
Asphyxiation Risk.
• Negative pressure can cause spillage of
combustion fumes, soot and carbon monoxide.
• Appliance needs to draft properly for safety.
L. Negative Pressure
K. Clear Space
• Do NOT place combustible objects within 4 ft (1.2 m) of
the front of appliance (Figure 16.1).
• Mantel - avoid placing candles and other heat-sensitive
objects on mantel or hearth. Heat may damage these
objects.
Figure 16.1
Maintain 4 ft (1.22m) clearance to
combustible in front of appliance
WARNING
Do NOT place combustible objects in front of the
appliance. High temperatures may ignite clothing, furniture
or draperies.
August 13, 2018 7039-177C 17
2100 Millennium
ISSUES SOLUTIONS
Odor from appliance
When rst operated, this appliance may release an odor for the rst several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Whirring sound
If the optional blower has been installed, the blower produces a whirring sound which
increases in volume as the speed is increased.
CONTACT YOUR DEALER for additional information regarding operation and troubleshooting.
Visit www.quadrare.com to nd a dealer.
M. Frequently Asked Questions
Fire Risk.
Keep combustible materials, gasoline and other
ammable vapors and liquids clear of appliance.
• Do NOT store ammable materials in the
appliance’s vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID
OR SIMILAR LIQUIDS TO START OR
“FRESHEN UP” A FIRE IN THIS APPLIANCE.
• Keep all such liquids well away from the
appliance while it is in use.
• Combustible materials may ignite.
WARNING
WARNING
Fire Risk.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPHTHA OR
ENGINE OIL.
• Do NOT burn treated wood or wood with salt
(driftwood).
• May generate carbon monoxide if burn
material other than wood.
May result in illness or possible death.
18 7039-177C August 13, 2018
2100 Millennium
A. Quick Reference Maintenance Guide
When properly maintained, your replace will give
you many years of trouble-free service. Contact your
dealer to answer questions regarding proper operation,
troubleshooting and service for your appliance. Visit
www.quadrare.com/owner-resources to view basic
troubleshooting, FAQs, use & care videos.
CAUTION! Allow the appliance to completely cool down
before performing any cleaning or maintenance.
Start the rst inspection after the rst 2 months of use,
or if performance changes, and adjust your schedule
accordingly. Maintenance is required for safe operation
and must be performed to maintain your warranty.
Frequency Task
Bafe & Blanket
MONTHLY
or after every
cord of wood
Bafe and blanket placement is critical to heat output, efciency
and overall life of the appliance. Make sure the bafe is pushed
all of the way to the back of the rebox and the blanket is laying
at. Inspect bafe for cracks.
Déflecteur
Isolant
Optional Blower
YEARLY
or
After Every
4 Cords of
Wood
Vacuum the blower impellers.
Chimney System
EVERY 2
MONTHS
or
After Every
4 Cords of
Wood
T
he chimney and chimney cap must be inspected for soot and
creosote every two months during the burn season or more
frequency if chimney exceeds or is under 14-16 ft (4.3m-4.8m)
measured from bottom of appliance.
This will prevent pipe blockage, poor draft, and chimney res.
Always burn dry wood to help prevent cap blockage and creosote
build-up.
Firebrick & Ash Removal
WEEKLY
or
After Every
25 Loads of
Wood
Ashes must be cool before you can dispose of the ashes in a
non-combustible container.
Firebrick is designed to protect your rebox. After ashes are
removed, inspect the rebrick and replace rebricks that are
crumbling, cracked or broken.
Door & Glass Assemblies
WEEKLY
or
After Every
25 Loads of
Wood
Keep door and glass gasket in good shape to maintain good burn
times on a low burn setting. To test: place a dollar bill between
the appliance and door and then shut the door. If you can pull the
dollar out, remove one washer from door handle behind latch cam
and try again. If you can still pull it out, replace the door gasket.
Check the glass frame for loose screws to prevent air leakage.
Check glass for cracks.
Door Handle
WEEKLY
or
After Every
25 Loads of
Wood
Check the door latch for proper adjustment. This is very
important especially after the door rope has formed to the
appliance face.
Check door handle for smooth cam operation.
Contre-écrou
Section transversale de la porte
(exemple)
Verrou à came
Rondelles
d’espacement
Clé carrée
Poignée
de porte
Poignée
à ressort
These are generic drawings and may not represent your model.
3 Maintenance and Service
August 13, 2018 7039-177C 19
2100 Millennium
CAUTION
• Do not use polishes with abrasives. It will scratch
plated surfaces.
1. Creosote (Chimney) Cleaning
• Frequency: Every 2 months during heating season or
as recommended by a certied chimney sweep; more
frequently if chimney exceeds or is under 14-16 ft.
(measured from bottom of appliance)
• By: Certied Chimney Sweep
Remove all ash from the rebox and extinguish all hot
embers before disposal. Allow the appliance to cool
completely. Disconnect ue pipe or remove bafe and
ceramic blanket from appliance before cleaning chimney.
Otherwise residue can pile up on top of the bafe and
ceramic blanket and the appliance will not work properly.
(See Bafe Removal on page 23). Close the door tightly.
The creosote or soot should be removed with a brush
specically designed for the type of chimney in use. Clean
out fallen ashes from the rebox.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build
creosote deposits quicker, so it is important to check the
chimney from the top as well as from the bottom.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which
combine with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool
chimney ue of a newly-started or a slow-burning re. As
a result, creosote residue accumulates on the ue lining.
When ignited, this creosote creates an extremely hot re
which may damage the chimney or even destroy the house.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to
determine if a creosote or soot buildup has occurred. If
creosote or soot has accumulated, it should be removed to
reduce the risk of a chimney re.
B. General Maintenance
WARNING
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and chimney once
every two months during heating season.
• Remove creosote to reduce risk of chimney
re.
• Ignited creosote is extremely HOT.
Fire Risk.
Disposal of Ashes
• Ashes should be placed in metal container
with tight tting lid.
• Do not place metal container on combustible
surface.
• Ashes should be retained in closed container
until all cinders have thoroughly cooled.
WARNING
Fire Risk.
• Do not use chimney cleaners or ame
colorants in your appliance. Will corrode
chimney pipe.
WARNING
2. Cleaning Plated Surfaces
• Frequency: Prior to first burn and then as desired
• By: Homeowner
Clean all the ngerprints and oils from plated surfaces
BEFORE ring the appliance for the rst time. If not
cleaned properly before lighting your rst re, the oils can
cause permanent markings on the plating.
After the plating is cured, the oils will not affect the nish
and little maintenance is required. Wipe clean as needed.
3. Disposal of Ashes
• Frequency:
When ash is within 1-3/4 in. (44mm) of
rebox lip
• By: Homeowner
Ashes should be placed in a metal container with a tight
tting lid. The closed container of ashes should be placed
on a non-combustible oor or on the ground, well away
from all combustible materials, pending nal disposal. If the
ashes are disposed of by burial in soil or otherwise locally
dispersed, they should be retained in the closed container
until all cinders have thoroughly cooled.
20 7039-177C August 13, 2018
2100 Millennium
1. Glass Cleaning
• Frequency: As desired
• By: Homeowner
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed by
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven
cleaner left on during the next ring can permanently stain
the glass and damage the nish on metal surfaces.
A portion of the combustion air entering the rebox is
deected down over the inside of the door glass. This
air ow “washes” the glass, helping to keep smoke from
adhering to its surface.
When operated at a low burn rate, less air will be owing
over the glass and the smokey, relatively cool condition of a
low re will cause the glass to become coated.
Operating the appliance with the Burn Rate Air Control and
Start-Up Air Control all the way open for 30-45 minutes
should remove the built up coating.
CAUTION
• Do not use polishes with abrasives. It will scratch
surfaces.
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

Quadrafire 2100 Millennium Wood Stove Manuel utilisateur

Marque
Quadrafire
Modèle
2100 Millennium Wood Stove
Catégorie
Cheminées
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents