Midmark RTLS Mode d'emploi

MIDMARK RTLS

FCC User Guide

For BLE TRACKING

Version 1.7 6/14/2022

FCC User Guide

This document contains user information on technology that is proprietary to

Midmark RTLS Solutions, Inc. Permitted transmittal, receipt or possession of this

document does not express license or imply any rights to use, sell, design or

manufacture this information. No reproduction, publication or disclosure of

this information, in part or in whole, shall be made without prior written

authorization of Midmark RTLS Solutions, Inc.

WARNING! This product is not designed, intended, authorized or warranted

for use in any life support or other application where product failure could

cause or contribute to personal injury, death or severe property damage.

All patient, staff and asset names in this document are fictional.

Because Midmark RTLS Solutions, Inc. is continually improving its products,

specifications within all Midmark RTLS manuals are subject to change without

notice.

Midmark RTLS Solutions Inc. is an ISO 9001 Certified Company.

Midmark RTLS products and solutions are provided by Midmark RTLS

Solutions, Inc. f/k/a Versus Technology, Inc., a wholly owned subsidiary of

Midmark Corporation.

For more information, contact 1.800.MIDMARK, or call Midmark RTLS directly

at 1.877.983.7787. Visit our website at midmarkRTLS.com.

Revision Date: October 2020

Proprietary Information

FCC User Guide

FCC STATEMENT:

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two

conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may

cause undesired operation.

2. any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable

protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

3. FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment should be installed and operated with

minimum distance 20cm between the radiator (VER5800 Plug in Sensor) & your

body.

The device shall be used in such a manner that the potential for human contact

normal operation is minimized. This equipment complies with FCC radiation

exposure limits set forth for an uncontrolled environment. This device and its

antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter.

Components comply with part 15 of the FCC Rules. Operation is subject to the

following two conditions: 1) These devices may not cause harmful interference, and

2) These devices must accept any interference received, including interference that

may cause undesired operation.

FCC User Guide

5. CANADA STATEMENT:

This device complies with RSS-210 of the Industry Canada Rules. Operation is

subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de

l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est

susceptible d'en compromettre le fonctionnement

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada’s license-exempt RSSs. Operation is

subject to the following two conditions:

1. This device may not cause interference, and

2. This device must accept any interference, including interference that

may cause undesired operation.

6. Canada RF Exposure Statement:

The device shall be used in such a manner that the potential for human contact

normal operation is minimized. This equipment complies with RSS-102 radiation

exposure limits. This equipment should be installed and operated with a minimum

distance of 20 cm between the radiator and your body. This device and its

antenna(s) must not be co-located or operating in conjunction with any other

antenna or transmitter.

Le dispositif doit être utilisé de manière à réduire au minimum le risque de

fonctionnement normal en contact humain. Cet équipement est conforme aux

limites d’exposition au rayonnement RSS-102. Cet équipement doit être installé et

utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps. Cet

appareil et ses antennes ne doivent pas être situés conjointement ou fonctionner

conjointement avec une autre antenne ou un autre émetteur.

VER-585x

The device shall be used in such a manner that the potential for human contact normal

operation is minimized. This equipment complies with RSS-102 radiation exposure

limits. This device and its antenna(s) must not be co-located or operating in conjunction

with any other antenna or transmitter.

FCC User Guide

Document Control

Version

Meeting Date

Contributors

Topics

Discussed

1.0

12-30-2020

BW

Initial draft of

FCC user

guide.

1.1

1-5-2021

BW

Updated

1.2

1-14-2021

BW

Updated

1.3

4-12-2021

BW

Updated

1.4

4/21-2021

BW

Updated

1.5

9/16/2021

BW

Updated

1.6

1/11/2022

BW

Added IC

info.

1.6.1

2/1/2022

BW

Update IC

1.6.2

2/7/2022

BW

Update IC

1.7

6/9/2022

BW

Updated for

Badge VER-

585x

  FCC User Guide 
 
Page 6       Rev. 1.0  6/14/2022                             © 2020 Midmark RTLS Solutions, Inc., Traverse City, Michigan USA 
 
 
 
 
Table of Contents 
 
I. Introduction ...................................................................................................... 7 
A. Purpose of This Guide ...................................................................................... 7 
II. System Description ........................................................................................... 7 
III. Asset Tracking Platform Parts List ................................................................. 8 
IV. Asset Tracking Platform Component Overview ........................................ 9 
A. Signaling Devices and Supplies ...................................................................... 9 
1. BLE Tags ............................................................................................................. 9 
V. Specifications .............................................................................................. 13 
VI. Product Appearance ................................................................................ 14 
 
 

Example FCC User Guide

I. Introduction

A. Purpose of This Guide

This document is intended to provide the information required to

install the hardware component of a Midmark VER-5800 BLE-Plug-In

Sensor.

II. System Description

The Bluetooth Low Energy – Access Controller Sensor (BLE-AC) provides a

way for indoor positioning. The Midmark VER-5800 BLE- Plug-In Sensor acts as

a gateway with an integrated WIFI wireless communication technology to

forward the traffic to the cloud. The Midmark BLE Plug-In Sensor scans for BLE

devices nearby to gather location information then uploads these messages

to the cloud servers. To configure the sensor there is a Midmark app for

iPhone and Androids that assigns the WIFI credentials and sets the sensor

cloud connection. The cloud connection passes the data along to the

indoor mapping location application.

Example FCC User Guide

III. Asset Tracking Platform Parts List

The table below lists all current available Asset Tracking Platform hardware

components and their related part numbers:

Part Number

Description

VER-5800 BLE-Plug-In

Sensor to scan for BLE signals

VER5864_BLE_IR_Tag

BLEIR Equipment tag

VER5869_BLE_Tag

BLE Equipment tag

VER5854 BLE_IR Badge

BLEIR Personnel Badge

Example FCC User Guide

IV. Asset Tracking Platform Component Overview

A. Signaling Devices and Supplies

1. BLE Tags

VER-58xx BLE/IR Asset Tag (Ext-XL) Leverage the locating

precision of the Midmark RTLS infrared (IR) sensory network

while supplementing your RTLS with Midmark's near room-level

Bluetooth Low Energy (BLE) technology. The BLE/IR Asset Tag,

affixed to equipment or other assets, emits its unique ID using

both BLE and IR signals. When equipment is in an area

covered by IR sensors, Midmark RTLS reports the precise chair-

, bed or room-level location. Outside of the IR sensory network

where BLE sensors are installed, Midmark RTLS provides near

room-level location information (within three meters).

VER-5869 BLE Asset Tag Providing long battery life and near

room-level locating precision, the BLE Asset Tag uses the latest

Bluetooth Low Energy (BLE) technology. Affixed to assets or

other equipment, the tag‘s BLE signals transmit a unique

identifier received by the Midmark RTLS BLE sensors. Using a

signal strength algorithm, the tags are located by Midmark

RTLS with near room-level precision (within three meters).

Compatibility Note: Ext-XL tags feature improved battery life

and are only compatible with XL Wired IR Sensors or Wireless

Sensors. When used with the Wired Sensory Network, the tag’s

20-bit Extended ID technology requires VER-2404-DHCP

Collectors or later and VER-2032-DHCP Concentrators or later

and VER-2032-DHCP Concentrators or later.

Example FCC User Guide

BLE/IR Asset Tag Mounting + Assembly

Example FCC User Guide

Staff tag.

VER585x BLEIR Badge front view

VER585x BLEIR Badge Back view

Example FCC User Guide

V. Asset Tracking Sensor Placement Guidelines

A. Use the following guidelines for sensor placement in an

available 110v outlet:

• The distance between sensors should be less than 25 feet

• The height from the floor should be between 1 and 12 feet in a wall

mounted receptacle

• Room sensor placement preference is away from corridors and room entry doors

• Corridor sensor placement preference is away from doors for rooms with a sensor

• Sensors should be 9 to 30 feet away from floor transitions (e.g., stairs, escalators,

and elevators)

VI. Controlling Relay

A. For the initial release of the sensor, the relay is set to the

on state with no option to control it.

When relay is set, power is passed through.

Example FCC User Guide

VII. Specifications

1. Basic Specifications

Wireless technology

BLE, WI-FI

Input voltage

120VAC

Output voltage

120VAC

Impulse Voltage

1500 V

Max load current

15A

Max load

1800W

Operating temperature &

humidity

0ºC~40 ºC/10%~90%

Plug type

North America

Dimensions

42x38x69mm

2. Wi-Fi Specifications

Wi-Fi protocol

802.11b/g/n

Frequency band

2.4Ghz

Transmission power

11n: MCS7 13dB

11b: 18.5dB

3. Bluetooth Specifications

BT standard

V4.2 BLE

Receiving sensitivity

-97dB

4. Button Specifications

5 second long press

Trigger OTA update

5. LED Indicator

OTA update

Cycles RGB led’s

Detecting packets

Flashes Blue, stops after 60

seconds.

Packets sent to cloud

Flashes Green, stops after

60 seconds.

Example FCC User Guide

6. UL

“Type 1 Enclosure”,

Purpose of control: Operating Control;

Construction of control: Portable Direct Plug In Type;

Type 1 Action;

Pollution Degree: 2;

VIII. Product Appearance

Product Photo

Dimensions (in mm)

Figure 1 Example Caption and Scree

Midmark RTLS Mode d'emploi

Midmark RTLS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents