Inogen One G2 Manuel utilisateur

®

user manual

Contents

Chapter 1 01 Intended Use, Contraindications and General Precautions

Chapter 2 03 Description of the Inogen One® G2 Oxygen Concentrator

03 Important Parts of the Inogen One® G2 Oxygen Concentrator

04 User Controls

05 User Interfaces

05 Input / Output Connections

06 Power Supply Options

08 Inogen One® G2 Accessories

Chapter 3 11 Operating Instructions

11 General Instructions

15 Additional Operating Instructions

18 Battery Operating Instructions

19 Battery Care and Maintenance

Chapter 4 21 Inogen One® G2 Oxygen Concentrator Audible and

Visible Signals (including Alarms)

Chapter 5 29 Troubleshooting

Chapter 6 31 Cleaning, Care and Maintenance

31 Cannula Replacement

31 Case Cleaning

32 Filter Cleaning and Replacement

34 Other Service and Maintenance

34 Disposal of equipment and accessories

Chapter 7 35 Symbols Used on Concentrator and Accessories

Chapter 8 37 Inogen One® G2 System Speciﬁcations

English

1Intended Use, Contraindications

and General Precautions

Intended Use, Contraindications and General Precautions Chapter 1 1

Intended Use

The Inogen One® G2 Oxygen Concentrator is used on a prescriptive basis by patients

requiring supplemental oxygen. It supplies a high concentration of oxygen and is used

with a nasal cannula to channel oxygen from the concentrator to the patient. The Inogen

One® G2 may be used in home, institution, vehicle, on an airplane and various mobile

environments.

CAUTION USA Federal law restricts this device to sale by or on the order of a

physician. May also be applicable in other countries.

WARNING Availability of an alternate source of oxygen is recommended in case of

power outage or mechanical failure. Consult your equipment provider for

type of back-up system recommended.

CAUTION It is the responsibility of the patient to make back-up arrangements for

alternative oxygen supply when traveling; Inogen assumes no liability for

persons choosing not to adhere to manufacturer recommendations.

!

C

English

2

Contraindications

WARNING This device is NOT INTENDED to be life sustaining or life supporting.

CAUTION

Under certain circumstances, the use of non-prescribed oxygen

therapy can be

hazardous. This device should be used only when

prescribed by a physician.

CAUTION Additional monitoring or attention may be required for patients

using this device who are unable to hear or see alarms or communicate

discomfort. If the patient shows any signs of discomfort, a

physician should be consulted immediately.

CAUTION The Inogen One® G2 is not designed or speciﬁed to be used with a

humidiﬁer or nebulizer. Use of this device with a humidiﬁer or

nebulizer may impair performance and/or damage the equipment.

!

C

!

C

!

C

General Precautions

WARNING The device produces enriched oxygen gas which accelerates

combustion. Do NOT ALLOW SMOKING OR OPEN FLAMES within

10 feet of this device while in use.

WARNING Do not submerse the Inogen One® G2 or any of the accessories in liquid.

Do not expose to water or precipitation. Do not operate in rain.

This could lead to electrical shock and/or damage.

CAUTION

Do not use oil, grease, or petroleum-based products on or near the

Inogen One® G2.

CAUTION Never leave the Inogen One® G2 in an environment which can reach

high temperatures, such as an unoccupied car in high temperature

environments. This could damage the device.

Important Parts of the Inogen One® G2 Oxygen Concentrator

Description of the Inogen One®

G2 Oxygen Concentrator

Description of the Inogen One® G2 Oxygen Concentrator Chapter 2 3

2

On/Off

Button

Alert/Alarm

Light

Flow Control

Display

Backlight

Button

Breath

Detection

Light

Audible

Alarm

Button

English

4

User Controls

ON / OFF Button

Press once to turn “ON”; Press and hold for one second to turn “OFF”.

Audible Alarm Button

Pressing this button will toggle the Inogen One® G2’s breath detection

alert on and off:

1. Default Mode. When the Inogen One® G2 is powered

up, the breath detection alert is disabled. The display’s mode indication

area is empty in Default Mode.

2.

Breath Detection Alert Mode. The Inogen One® G2 will alert with

audible and visual signals for “no breath detected” when this mode is

enabled and no breath has been detected for 60 seconds. The display’s

mode indication area will show a bell icon when the alert is enabled.

Flow Setting Control Buttons

Use the – or + ﬂow setting control buttons to select the setting

as shown on the display. There are ﬁve settings, from 1 to 5.

Display Backlight Button

Push on; automatically turns off.

Description of the Inogen One® G2 Oxygen Concentrator Chapter 2 5

User Interfaces

Display

This screen displays information regarding ﬂow setting, power

status, battery life and errors. If you would like to change the

language on the Inogen LCD Screen contact Inogen Client

Services.

Indicator Lights

A red light indicates either a change in operating status or a

condition that may need response (alarm). A ﬂashing light is

higher priority than non-ﬂashing.

Audible Signals

An audible signal (beep) indicates either a change in

operating status or a condition that may need response (alarm).

More frequent beeps indicate higher priority conditions.

Input / Output Connections

Particle Filter

The ﬁlter must be in place at the intake end of the concentrator

during operation to keep input air clean.

Cannula Nozzle Fitting

The nasal cannula connects to this nozzle for Inogen One® G2

output of oxygenated air.

DC Power In

Connection for power connection from the Universal Power

Supply.

English

6

Power Supply Options

12-Cell Rechargeable Lithium Ion Battery

The battery will power the Inogen One® G2 without connection to an

external power source. When fully charged, the battery will provide 2 to 4

hours of operation. The battery recharges when properly installed in the

Inogen One® G2 and the concentrator is connected to AC or DC power.

Recharging time is up to 4 hours. See information in the “Battery Care and

Maintenance” section.

UNIVERSAL POWER SUPPLY

Overview

The Inogen Universal Power Supply (BA-107/207) is used to power the Inogen One® G2

concentrator from an AC power source or a DC power source. This allows the user to

power the concentrator in the home, in a vehicle or other places where AC or DC power is

available.

Description

The Inogen One® G2 Universal Power Supply is speciﬁcally designed for use with the

Inogen One® G2 Oxygen Concentrator (IO-200). The Universal Power Supply provides the

precise current and voltage required to safely power the Inogen One® G2, and is designed

to operate from speciﬁed AC and DC power sources. When used with AC power sources,

the supply automatically adapts to input voltages from 100V to 240V (50-60HZ)

permitting use with most power sources throughout the world.

The Universal Power Supply will charge the Inogen One® G2 Battery when used with AC

input power or when used with a DC power supply, such as the one found in your car. Due

to aircraft power limitations, the Universal Power Supply cannot be used to charge the

Inogen One® G2 Battery when used on an aircraft.

The Universal Power Supply is used with the following components:

• Power Supply with attached power output cable to connect to the Inogen One® G2

• Automobile DC cigarette lighter Power Input Cable

• AC Power Input Cable.

7Description of the Inogen One® G2 Oxygen Concentrator Chapter 2

Power Output Plug

Universal Power Supply

LED Indicator Light

AC Input

DC cigarette lighter Power Plug for use in Automobile/RV/Boat/Aircraft

DC Input

AC Power Plug

English

Inogen One® G2 Accessories

WARNING

Do not use power supplies/adapters or accessories other than those

speciﬁed in this User Manual. The use of non-speciﬁed accessories may

create a safety hazard and/or impair equipment performance.

Nasal Cannula

A nasal cannula must be used with the Inogen One® G2 to provide

oxygen from the concentrator. A single lumen cannula up to 25

feet in length to ensure proper breath detection and oxygen

delivery is recommended.

NOTE

Increasing the cannula length may reduce the perceived noise during

oxygen bolus delivery.

Carry Bag

The Carry Bag provides a protective cover with a handle and

shoulder strap to enable you to carry the Inogen One® G2.

The Inogen One® G2 can be operated using battery power

during transport with the Carry Bag.

Cart

The Cart has wheels and a telescoping handle to provide easy

transport of the Inogen One® G2. The Inogen One® G2 can be operated

using battery power during transport. Place the Carry Bag over the

Cart. Make sure the Cart handle is inserted between the elastic strap

in the back of the carry bag and the front of the carry bag.

8

!

C

Description of the Inogen One® G2 Oxygen Concentrator Chapter 2 9

Airline DC 4-Pin Power Input Cable

DC 4-Pin power Power Plug for use on selected aircraft.

Please check with airline for power port availability.

24 Cell Rechargeable Lithium Ion Battery

The battery will power the Inogen One® G2 without connection

to an external power source. When fully charged, the battery will

provide 4 to 8 hours of operation. The battery recharges when

properly installed in the Inogen One® G2 and the concentrator is

connected to AC or DC power. Recharging time is up to 8 hours.

See information in the “Battery Care and Maintenance” section.

English

Operating Instructions

Operating Instructions Chapter 3 11

3

!

C

Intake

Exhaust

General Instructions

1. Place the Inogen One® G2 in a well ventilated

location.

Air intake and exhaust must have clear access.

Locate the Inogen One® G2 in such a way that any auditory

alarms may be heard.

WARNING Avoid use of the Inogen One® G2 in presence of pollutants, smoke

or fumes. Do not use the Inogen One® G2 in presence of ﬂammable

anesthetics, cleaning agents or other chemical vapors.

CAUTION Do not obstruct air intake or exhaust when operating the device.

Blockage of air circulation or proximity to a heat source may lead to

internal heat buildup and shutdown or damage to the concentrator.

2. Ensure the particle ﬁlter is in place.

CAUTION Do not operate the Inogen One® G2 without the

particle ﬁlter in place. Particles drawn into the

system may damage the equipment.

3. Install the battery.

Insert the Inogen One® G2 battery by sliding battery into place

and locking at bottom of concentrator.

English

12

CAUTION The Inogen One® G2 battery acts as a secondary power supply in the event of

a planned or unexpected loss of the AC or DC external power supply. When

operating the Inogen One® G2 from an AC or DC external power supply, a

properly inserted Inogen One® G2 battery should be maintained in the unit.

This procedure will ensure uninterrupted operation and will operate all

alarms and alerts in the event of a loss of the external power supply.

NOTE

The Inogen One® G2 Battery requires an initial full charge of uninterrupted

charging from an empty state using the Inogen One® G2 on the AC power

source. Do not run the Inogen One® G2 on battery power until this initial

charging has been completed.

4. Connect the Universal Power Supply.

Connect the AC Power plug to the Universal Power Supply. Connect the

AC Power Plug to the power source and connect the Power Output Plug to

the Inogen One® G2. The green LED on the Universal Power Supply will be

illuminated and a beep will sound from the concentrator.

CAUTION Ensure the Universal Power Supply is in a well ventilated location as it relies

on air circulation for heat dissipation. The Universal Power Supply may become

hot during operation. Make sure the Universal Power Supply cools down before

handling.

NOTE It is not recommended to use an AC plug adapter with the Universal Power

Supply. Use Inogen speciﬁed AC Power Input cables for international use.

CAUTION The Universal Power Supply is not water resistant.

CAUTION Do not disassemble the Universal Power Supply. This may lead to

component failure and/or safety risk.

CAUTION Do not place anything in the Universal Power Supply port other than the

supplied wall cord. Avoid the use of electrical extension cords with the Inogen

One® G2. If an extension cord must be used, use an extension cord that has

an Underwriters Laboratory (UL) Mark and a minimum wire thickness of 18

gauge. Do not connect any other devices to the same extension cord.

Operating Instructions Chapter 3 13

NOTE Under certain conditions (see Technical Speciﬁcations) the Universal

Power Supply may shut down. The green LED will blink or will no longer

be illuminated. If this occurs, disconnect the Power Supply for at least

10 seconds and reconnect.

NOTE

When the

Universal

Power Supply is disconnected from the AC outlet, also

disconnect it from the concentrator to avoid unnecessary battery discharge.

5. Connect the nasal cannula tubing to the nozzle ﬁtting.

Nozzle ﬁtting is located next to the handle of the Inogen One® G2.

Use of a single lumen cannula up to 25 feet in length to ensure

proper breath detection and oxygen delivery is recommended

. Additional

titration may be needed to ensure proper oxygen

delivery when using a particular cannula.

CAUTION

To ensure oxygen ﬂow, ensure that the nasal cannula is properly connected to

the nozzle ﬁtting and that the tubing is not kinked or pinched in any way.

CAUTION

Replace the nasal cannula on a regular basis. Check

with your equipment

provider or physician to determine how often the

cannula should be replaced.

6. Turn on your Inogen One® G2 by pressing the ON/OFF Button.

A single short beep will sound after the Inogen logo is displayed. “Please

Wait” will appear while the concentrator starts up. The display will indicate

the selected ﬂow setting and power condition. Following a brief start-up

sequence, a warm up period up to 2 minutes will initiate. During this time

period the oxygen concentration is building to, but may not have reached,

speciﬁcation. Additional warm up time may be needed if your Inogen One®

G2 has been stored in extremely cold temperatures.

English

!

C

14

7. Set the Inogen One® G2 Concentrator to the ﬂow rate prescribed by your physician or

clinician.

Use the + or – setting buttons to adjust the Inogen One® G2 to the desired setting.

The current setting can be viewed on the display.

8. Position the nasal cannula on your face and breathe through your nose.

The Inogen One® G2 will sense the onset of inhalation and deliver

a burst of oxygen at a precise time when you inhale. The Inogen

One® G2 will sense each breath and continue to deliver oxygen

in this manner. As your breathing rate changes, the Inogen One®

G2 will sense these changes and deliver oxygen only as you need

it. At times, if you inhale very quickly between breaths the Inogen

One® G2 may ignore one of the breaths, giving the appearance of a

missed breath. This may be normal as the Inogen One® G2 senses

and monitors the changes in your breathing pattern. The Inogen

One® G2 will normally sense the next breath and deliver oxygen

accordingly.

A green light will ﬂash each time a breath is detected. Make certain that the nasal cannula

is properly aligned on your face and you are breathing through your nose.

WARNING If you begin to feel ill or are experiencing discomfort while using this

device, consult your physician immediately.

CAUTION The Inogen One® G2 is designed to provide a ﬂow of high purity oxygen.

An advisory alarm, “Oxygen Low”, will inform you if oxygen concentration

drops. If alarm persists, contact your equipment provider.

General

To remove power, unplug the input cord from its source (i.e., AC wall outlet, car cigarette

lighter adapter).

CAUTION Ensure the Universal Power Supply is powered from only one power source

(AC or DC) at any given time. The Universal Power Supply may not operate

properly if simultaneously powered using both AC and DC sources.

Operating Instructions Chapter 3 15

Additional Operating Instructions

For Use In Home With AC Power

For operation of the Power Supply using an AC power source, follow these instructions:

1. Connect the AC Input to the power supply.

2. Connect the AC Power Plug to the power source and connect the Power Output

Plug to the Inogen One® G2. The green LED will be illuminated, indicating the

Universal Power Supply has input power.

Traveling With Your Inogen One® G2 System

The Inogen One® G2 System makes travel by plane, boat, car or train more convenient

for oxygen users than ever before. Now you get the same quality performance and

convenience while on the go that you’re used to receiving from your Inogen One® G2 at

home. Here are some useful and important instructions for maximizing performance

and convenience when using your Inogen One® G2 while traveling.

You should begin planning for a trip with a checklist of items to remember. This checklist

should include:

✓Universal Power Supply

✓ Extra Battery(s) if required

✓Important phone numbers, such as those of your physician and home healthcare

provider, or providers in the area you will be traveling

✓ Plan for backup oxygen in the event of a prolonged power outage or mechanical failure.

For Use In Automobile/RV/Boat

For operation of the Universal Power Supply using a DC power

source, follow these instructions:

1. Connect the DC Input to the power supply.

2. Connect the DC Power Plug (Cigarette Lighter Adapter) to

the power source and connect the Power Output Plug to the

Inogen One® G2. The green LED will be illuminated, indicating

the power supply has input power.

English

3. The plug should insert into the socket without excessive force and securely remain in

place. The Cigarette Lighter Adapter comes with a slide switch pre-adjusted to the narrow

position. This will ﬁt most automobile cigarette lighter sockets. If the Cigarette Lighter

Adapter is loose in the socket, adjust the switch to the "wide" position.

4. Ensure that the automobile power socket is adequately fused for the Inogen One® G2

power requirements (minimum 15 Amp).

WARNING The tip of the Cigarette Adapter Plug becomes HOT when in use. Do not touch

the tip immediately after removal from an auto cigarette lighter socket.

CAUTION Ensure the automobile power socket is clean of cigarette ash and the adapter

plug ﬁts properly, otherwise overheating may occur.

CAUTION Do not use the Universal Power Supply with a cigarette plug splitter or with

an extension cable. This may cause overheating of the DC power input cable.

CAUTION Do not jump start the automobile with the Universal Power Supply connected.

This may lead to voltage spikes which could shut down and/or damage the

Universal Power Supply.

CAUTION When powering the Inogen One® G2 in an automobile ensure the engine is

running. Operating the device without the engine running may drain the car

battery.

Traveling By Air

The FAA allows the Inogen One® G2 onboard all U.S. aircraft, here are a few points to make air

travel easy.

Planning Your Flight

When ﬂying with the Inogen One® G2, you must inform the airline that you will be using your

Inogen One® G2 onboard the aircraft. You must also keep a signed statement from

your physician with you that includes:

• Your ability to see/hear alarms and appropriately respond.

• When oxygen use is necessary (all or a portion of the trip).

• Maximum ow rate corresponding to the pressure in the cabin under normal operating

conditions.

16

• A new statement will not be necessary each time you y, but the statement should be

available during every ﬂight.

• Some airlines may equip their aircraft with onboard electrical power. You may have an

opportunity to request a seat with a power port which can be used to power your Inogen One®

G2. However, availability varies by airline, type of aircraft and class of service. You should check

with your airlines for availability and always plan on having sufﬁcient battery power for the

duration of your ﬂight, plus a conservative estimate of unanticipated delays.

• Because aircraft use different power port congurations, your Universal Power Supply is

equipped for use with two separate DC power adapters – a commonly used cigarette lighter

adapter, and a less common four-pin adapter (sold separately). Since it is difﬁcult to determine

which type of power supply your aircraft will have, it’s a good idea to keep both adapters

available when ﬂying.

Before Your Flight

Here are some things to keep in mind the day your ﬂight departs:

• Ensure your Inogen One® G2 is clean, in good condition and free from damage or other signs

of excessive wear or abuse.

• Bring enough charged batteries with you to power your Inogen One® G2 for the duration of

the ﬂight plus a conservative estimate of unanticipated delays.

• Regional/Commuter airlines do not offer onboard electrical power. If your travel plans call for

ﬂights on regional airlines, you will need sufﬁcient battery power for the duration of the ﬂight,

plus a conservative estimate of unanticipated delays.

CAUTION Airlines may not be equipped to provide backup oxygen.

• Arrive at the airport early. Airport security screening personnel may require extra time to

inspect your Inogen One® G2.

• While waiting to board your ight, you may be able to conserve battery power by using the

Universal Power Supply to power your Inogen One® G2 from an electrical outlet in the airport

terminal if available.

• You should inform the airline you will be using your Inogen One® G2. Have your physician

letter with you and ready for inspection if requested.

Operating Instructions Chapter 3 17

!

C

English

During Your Flight

1. If using airline power port, remove the Battery from the Inogen One® G2 Oxygen

Concentrator. Due to aircraft power limitations, the Universal Power Supply cannot

be used to charge the Inogen One® G2 Battery when onboard aircraft.

2. Connect the appropriate DC Power Plug for the type of available airline power

(see photos on page 7 and 9). Check with airline personnel to ensure compatibility.

• During taxi, takeoff and landing, stow your InogenOne® G2 under the seat in front of you.

Your Inogen One® G2 will ﬁt upright under most airline seats. However, if it doesn’t ﬁt you

may turn it on its side.

• It is not necessary to turn off your Inogen One® G2 during taxi, takeoff and landing if your

physician’s written statement requires you receive oxygen during these periods.

CAUTION A change in altitude (for example, from sea level to mountains) may affect

total oxygen available to the patient. The Inogen One® G2 has been veriﬁed

to provide oxygen to speciﬁcation up to 10,000 ft (3048 m). Consult your

physician before traveling to higher or lower altitudes to determine if your

ﬂow settings should be changed.

After Your Flight

• Remember to recharge additional batteries you may have used prior to your next ight.

Traveling By Bus, Train or Boat

Contact your carrier to ﬁnd out about available power port availability.

Battery Operating Instructions

Ensure that the battery is in place and charged. Disconnect the Inogen One® G2 from its

power source. While the Inogen One® G2 is operating on battery power, the battery will

discharge. The display will indicate the estimated remaining percentage (%) or minutes of use.

When the concentrator detects that the battery life is below 10% remaining, a low priority

alert will sound. When the battery is empty, the alert will change to a high priority.

When battery life is low, do one of the following:

• Plug the Inogen One® G2 into an AC or DC power source using the Universal Power Supply.

• Replace the battery with a charged battery after turning off the Inogen One® G2 (by

pressing the ON/OFF button).

• If the battery is drained, charge the battery or remove it from the concentrator.

18 Operating Instructions Chapter 3 19

If the Inogen One® G2 is being powered by the Universal Power Supply, batteries will charge

during operation. Leaving your Inogen One® G2 plugged in past the full charge time will not

harm the concentrator or the battery.

Normal Battery Charging

To ensure that your battery is properly charging, inspect that the correct AC and DC power

output plug adapter is being used and that the adapter is properly inserted into the power

outlet. Observe the display or lights that indicate charging status.

NOTE When starting to charge a fully discharged battery, the charging process may

start and stop during the ﬁrst few minutes.

Battery Care and Maintenance

Your Inogen One® G2 Lithium Ion Battery requires special care to ensure proper performance

and long life. Use only Inogen One® G2 Batteries with your Inogen One® G2 Concentrator.

Effect of Temperature on Battery Performance

The Inogen One® G2 12-Cell Battery powers the Inogen One® G2 Concentrator from 2 to 4

hours under most environmental conditions. To extend the run-time of your battery, avoid

running in temperatures less than 41˚F (5˚C) or higher than 95˚F (35˚C) for extended periods of

time.

Battery Time Remaining Clock

The Inogen One® G2 continuously displays battery time remaining. This displayed time is only

an estimate, and the actual time remaining may vary from this value.

Please Follow These Important Guidelines to Maximize Battery Performance and Life:

• Store battery in a cool, dry place. Store with a charge of 40-50%.

• Once per month: fully charge the battery then discharge to 10% and charge back to full.

• If using multiple batteries, make sure that each battery is labeled (1, 2, 3 or A, B, C, etc.) and

rotate on a regular basis. Batteries should not be left dormant for extended periods of time.

English

Mode

Power Text

Display Icons

The Inogen One® G2 display is divided into three areas. The upper left corner of the

display shows the breath detection alert status. The lower left corner indicates power

source and battery charge level. The right side of the display contains text information,

such as ﬂow setting, battery time remaining, and error notiﬁcations.

Power Status Icons

These icons are examples of those shown in the display’s power status window when the

Inogen One® G2 is operating on battery power.

Inogen One® G2 Oxygen

Concentrator Audible

and Visible Signals

Audible and Visible Signals Chapter 4

!C

Meaning

Battery is empty.

Battery has less than 10% charge remaining. This icon ﬂashes.

Battery has approximately 40% to 50% charge remaining.

Battery is full.

Icon

21

4

English

Power Status Icons (continued)

The icons below are examples of those shown when the Inogen One® G2 is operating

from an external power supply and charging the battery. The lightning bolt indicates

that an external power supply is connected.

!C

Meaning

Battery is charging with charge level between 60% and 70%.

The battery is fully charged and is charging as necessary to

maintain its charge.

Battery is charging with charge level less than 10%.

The Inogen One® G2 is operating from an external power source with no

battery present.

Icon

22

Mode Icons

These are the icons shown in the display’s mode window.

Display Text

NOTE When two conditions occur simultaneously, the condition with the

higher priority will be displayed.

Meaning

The breath detection alarm has been enabled.

The concentrator is in the standard breath detect mode, and the breath

detection alert is disabled. This is the default condition.

Icon

!C

[blank]

!C

Audible and Visible Signals Chapter 4 23

Informational Messages

The following information displays are not accompanied by any audible feedback or any

visual change in the indicator lights.

Condition/Action/Explanation

The Inogen logo is displayed at startup.

Default display when operating on battery power. “X”

represents the selected ﬂow setting (e.g., Setting 2).

“HH:MM” represents the approximate time remaining on

the battery charge (e.g., 1:45).

Default display when operating on an external power

supply and the battery is charging. “xx%” represents the

percent battery charge (e.g., 86%).

Default display when the battery is not charging or when the

time remaining is not available from the battery.

Display when the concentrator is plugged in and being used

to charge a battery (not being used for oxygen production).

It is normal to see a fully charged battery read between 95%

and 100% when external power is removed. This feature

maximizes the useful life of the battery.

Message Display & Text

Setting X Battery

HH:MM

Setting X Charging xx

(or) Battery Full

Setting X Battery xx%

Charging xx% (0r)

Battery Full

Notiﬁcations

The following notiﬁcation messages are accompanied by a single, short beep.

Condition/Action/Explanation

On/Off button has been pressed for two seconds.

Concentrator is performing system shut down.

Audible Alarm has been pressed for ﬁve seconds.

Message Display & Text

Inogen One®

Shutting Down

HH:MM

Vx.x

English

Low Priority Alerts

The following low priority alert messages are accompanied by a double beep and a

solid red light.

Condition/Action/Explanation

External power supply is too low to run the unit, which

is running on battery power despite being plugged in.

Check external power supply connections. If condition

persists, contact your equipment provider.

External power supply is too high. Check external power

supply connections. If condition persists, contact your

equipment provider.

Battery power is low, with less than 10% remaining. Attach

external power supply or power down and insert a fully

charged battery.

Battery error has occurred. Switch to a new battery or

remove battery and operate concentrator using external

power supply. If battery error recurs with same battery,

stop using the battery and contact your equipment

provider.

Concentrator is producing oxygen at a slightly low level

(<82%). If condition persists, contact your

equipment

provider

.

Message Display & Text

External

Power Low

External

Power High

Battery Low

Attach Plug

Battery Error

See Manual

Oxygen Low

See Manual

24

Low Priority Alerts (continued)

Condition/Action/Explanation

Battery has exceeded its charging temperature and charging

has stopped. The battery will not charge while this alert

is present but will begin to charge when the battery

temperature returns to the normal operating range.

If battery charging is desired sooner, remove the battery

from the concentrator and allow it to cool in an open area for

approximately 10-15 minutes. Then, re-insert the battery into

the Inogen One® G2. If the problem still persists, contact your

equipment provider.

Concentrator is producing oxygen but cannot report

battery status. Replace battery. If condition persists,

contact your equipment provider.

The concentrator requires servicing at the earliest

convenience. The concentrator is operating to speciﬁcation

and may continue to be used. Contact your equipment

provider to arrange for service.

The concentrator’s oxygen sensor has malfunctioned.

You may continue to use the concentrator. If the condition

persists, contact your equipment provider.

Message Display & Text

Remove Battery

to Cool

Comm Error

See Manual

Service Needed

02 Sensor Fail

See Manual

Audible and Visible Signals Chapter 4 25

English

Condition/Action/Explanation

Battery has exceeded temperature limit while concentrator

is running on battery power. If possible, move concentrator

to a cooler location or power unit with an external power

supply and remove battery. If condition persists, contact

your equipment provider.

Concentrator is not detecting a breath. Check that:

cannula is connected to concentrator, there are no kinks

in tubing, and cannula is positioned properly in your nose.

If Satellite Conserver is attached, make sure ﬂow control

on concentrator is set to Satellite Mode. This alert may be

enabled or disabled through use of the mode button.

Concentrator is experiencing an error, but is capable of

continued operation. As soon as you are able:

• Remove and re-insert battery, and/or

• Check external power supply connections.

If condition persists, contact your equipment provider.

Oxygen output concentration is below 50%. If condition

persists, switch to your backup oxygen source and contact

your equipment provider to arrange for service.

Message Display & Text

Battery HOT

Warning

No Breath Detect

Check Cannula

System Error

See Manual

Oxygen Error

Service Needed

Medium Priority Alerts

The following medium priority alert messages are accompanied by a triple beep,

repeated every 25 seconds, and a ﬂashing red light.

26

Condition/Action/Explanation

Concentrator has insufﬁcient battery power to produce

oxygen. Attach external power supply or exchange battery,

then restart unit if necessary by pressing On/Off button.

Battery has exceeded temperature limit while concentrator

is running on battery power. Concentrator has stopped

producing oxygen. If possible, move concentrator to a

cooler location, then turn power off and back on. Ensure air

intake and outlet vents have clear access and particle ﬁlter

is clean. If condition persists, switch to a backup source of

oxygen and contact your equipment provider.

Concentrator temperature is too high, and oxygen

production is shutting down. Ensure air intake and outlet

vents have clear access and particle ﬁlter is clean. If

condition persists, switch to a backup source of oxygen and

contact your equipment provider.

Message Display & Text

Battery Empty

Attach Plug

Battery HOT

Shut Down

System HOT

Shut Down

High Priority Alerts

CAUTION If you are not near the Inogen One® G2 you may not be able to hear or

see the high priority alerts. Make sure the Inogen One® G2 is in a

location where the alerts and alarms will be recognized if they occur.

The following high priority alert messages are accompanied by a ﬁve beep pattern,

repeated every 10 seconds, and a ﬂashing red light.

Audible and Visible Signals Chapter 4 27

English

Use external power supply or

replace battery with one that is

fully charged

Contact your equipment provider

Press On/Off button to power

concentrator

Check cannula and its connection

to concentrator nozzle

Battery is discharged

or no battery is

present

Malfunction

Concentrator is not

powered on

Cannula is not

connected properly or

is kinked or obstructed

Concentrator does

not power on when

On/Off button is

pressed

No oxygen

Condition/Action/Explanation

This may result from the concentrator being stored in a

cold environment (below 0ºC (32ºF)). Move to a warmer

environment to allow the unit to warm up before starting

it. If condition persists, switch to a backup source of

oxygen and contact your equipment provider.

Concentrator has stopped producing oxygen and is

shutting down. You should:

1. Note error number

2. Switch to backup oxygen source

3. Contact your equipment provider

Message Display & Text

System COLD

Shut Down

Error (###)

Service Needed

High Priority Alerts (continued)

28

Troubleshooting

Troubleshooting Chapter 5

Inogen One G2 Manuel utilisateur

Inogen One G2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents