Nextivity L41-7EB Mode d'emploi
- Catégorie
- Antennes réseau
- Taper
- Mode d'emploi
Safety Precautions
•When installing the equipment, all the requirements
of the manufacturer and the referenced standards
must be met.
• There are no user serviceable parts inside.
Warranty
Nextivity Inc provides a limited warranty for its prod-
ucts. For details, please refer to http://cel-.com/war-
ranty
Limitation of Liability
In no event shall Nextivity, nor its directors, employees,
agents, suppliers or End Users, be liable under con-
tract, tort, strict liability, negligence or any other legal
or equitable theory with respect to the Products or
any other subject matter of this Agreement (i) for any
lost prot, cost of procurement of substitute goods
or services, or special, indirect, incidental, punitive, or
consequential damages of any kind whatsoever or (ii)
for any direct damages in excess of (in the aggregate)
the fees actually received by Nextivity from End User
with respect to the Products actually purchased and
paid for.
See www.cel-.com for list of patents covering this
product.
FCC
Part 90 and Part 20 Signal Boosters. THIS IS A 90.219 CLASS B DEVICE
WARNING. This is NOT a CONSUMER device. It is designed for installation
by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an
FCC LICENSE or express consent of an FCC License to operate this device.
You MUST register Part 90 Class B signal boosters (as defined in 47
CFR 90.219) online at www.fcc.gov/signal-boosters/registration.
Unauthorized use may result in significant forfeiture penalties,
including penalties in excess of $100,000 for each continuing violation.
WARNING
Changes or modications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Statement
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equip-
ment and the receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interfer-
ence, and
2. this device must accept any interference re-
ceived, including interference that may cause
unde- sired operation.
In order to comply with FCC RF Exposure require-
ments:
Do not call your service provider until you have read the User Manual.
If you need help, visit: www.cel-.com/support/
Cel-Fi® SOLO RED
for Public Safety
MODEL NUMBER:
L41-7EB
MODEL NUMBER:
L41-7EB
PRODUCT INFORMATION PRODUCT INFORMATION
Cel-Fi® SOLO RED
for Public Safety
1. The donor antenna must be installed to
provide at least 65 cm separation from
the human body at all times.
2. The server antenna must be installed to
provide at least 20 cm separation from
the human body at all times.
Caution
This device may be operated ONLY in a fixed
location for in-building use. Home/personal use is
prohibited.
External Antenna: Only the antennas listed in the
Antenna Kitting section of the user manual are
allowed to be used with this device. Use of
unauthorized antennas, cables, and/or coupling
devices not conforming with ERP/EIRP and/or
indoor-only restrictions is prohibited.
Safety Precautions
•When installing the equipment, all the requirements
of the manufacturer and the referenced standards
must be met.
• There are no user serviceable parts inside.
Warranty
Nextivity Inc provides a limited warranty for its prod-
ucts. For details, please refer to http://cel-.com/war-
ranty
Limitation of Liability
In no event shall Nextivity, nor its directors, employees,
agents, suppliers or End Users, be liable under con-
tract, tort, strict liability, negligence or any other legal
or equitable theory with respect to the Products or
any other subject matter of this Agreement (i) for any
lost prot, cost of procurement of substitute goods
or services, or special, indirect, incidental, punitive, or
consequential damages of any kind whatsoever or (ii)
for any direct damages in excess of (in the aggregate)
the fees actually received by Nextivity from End User
with respect to the Products actually purchased and
paid for.
See www.cel-.com for list of patents covering this
product.
FCC
Part 90 and Part 20 Signal Boosters. THIS IS A 90.219 CLASS B DEVICE
WARNING. This is NOT a CONSUMER device. It is designed for installation
by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an
FCC LICENSE or express consent of an FCC License to operate this device.
You MUST register Part 90 Class B signal boosters (as defined in 47
CFR 90.219) online at www.fcc.gov/signal-boosters/registration.
Unauthorized use may result in significant forfeiture penalties,
including penalties in excess of $100,000 for each continuing violation.
WARNING
Changes or modications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
FCC Statement
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equip-
ment and the receiver.
3. Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
4. Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interfer-
ence, and
2. this device must accept any interference re-
ceived, including interference that may cause
unde- sired operation.
In order to comply with FCC RF Exposure require-
ments:
Do not call your service provider until you have read the User Manual.
If you need help, visit: www.cel-.com/support/
1. The donor antenna must be installed to
provide at least 65 cm separation from
the human body at all times.
2. The server antenna must be installed to
provide at least 20 cm separation from
the human body at all times.
Caution
This device may be operated ONLY in a fixed
location for in-building use. Home/personal use is
prohibited.
External Antenna: Only the antennas listed in the
Antenna Kitting section of the user manual are
allowed to be used with this device. Use of
unauthorized antennas, cables, and/or coupling
devices not conforming with ERP/EIRP and/or
indoor-only restrictions is prohibited.
[French: An de se conformer aux exigences d’exposition
RF ISED:
1. L’antenne du donneur doit être installée pour
fournir une séparation d’au moins 65 cm du
corps humain en tout temps.
2. L’antenne du serveur doit être installée pour
fournir une séparation d’au moins 20 cm du
corps humain en tout temps.
The Manufacturer’s rated output power of this equip-
ment is for single carrier operation. For situations
when multiple carrier signals are present, the rating
would have to be reduced by 3.5 dB, especially where
the output signal is re-radiated and can cause interfer-
ence to adjacent band users. This power reduction is to
be by means of input power or gain reduction and not
by an attenuator at the output of the device.
[FRENCH: La puissance de sortie nominale indiquée
par le fabricant pour cet appareil concerne son
fonctionnement avec porteuse unique. Pour des
appareils avec porteuses multiples, on doit réduire la
valeur nominale de 3,5dB, surtout si le signal de sortie
est retransmis et qu’il peut causer du brouillage aux
utilisateurs de bandes adjacentes. Une telle réduction
doit porter sur la puissance d’entrée ou sur le gain, et
ne doit pas se faire au moyen d’un atténuateur
raccordé à la sortie du dispositif.]
1. This device may not cause interference.
2. This device must accept any interference, in-
cluding interference that may cause undesired
operation of the device.
[French: L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développe-
ment économique Canada applicables aux ap-
pareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage ra-
dioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionne-
ment.]
CAN ICES-3 (A)/NMB-3(A)
Compliance Contact
In the event of regulatory compliance issue, please
contact Nextivity Inc. directly. Contact information is
available at www.nextivityinc.com.
Patents
This product is covered by Nextivity, Inc., US patents
and patents pending. Please refer to cel-.com for
details.
Copyright
Copyright © 2022 by Nextivity, Inc. All rights reserved.
Reproduction or media conversion by any means is
protected by copyright and may only occur with prior
written permission of Nextivity. Designed by Nextivity
in California.
Trademark
Cel-Fi and the Nextivity logo are trademarks of Nex-
tivity, Inc.
If you need help, visit: www.cel-.com/support.
legal_solo-red_classB_eng_22-0314 legal_solo-red_classB_eng_22-0314
Nextivity UK Ltd
Unit 9, Basepoint Business Centre Rivermead Drive, Westlea Swindon SN5 7EX
Nextivity Singapore Pte. Ltd.
2 Changi Business Park Avenue 1, Level 2 – Suite 16, 486015 Singapore
Bureau in Europe Union
Carrer Bassols 15-1, Bacelona 08026, Spain
Nextivity UK Ltd
Unit 9, Basepoint Business Centre Rivermead Drive, Westlea Swindon SN5 7EX
Nextivity Singapore Pte. Ltd.
2 Changi Business Park Avenue 1, Level 2 – Suite 16, 486015 Singapore
Bureau in Europe Union
Carrer Bassols 15-1, Bacelona 08026, Spain
Nextivity Inc.
16550 West Bernardo Drive, Bldg. 5, Suite 550
San Diego, CA 92127
www.cel-.com
Nextivity Inc.
16550 West Bernardo Drive, Bldg. 5, Suite 550
San Diego, CA 92127
www.cel-.com
420N007-L41-001-11RC420N007-L41-001-11RC
1. The donor antenna must be installed
to provide at least 65 cm separation
from the human body at all times.
2. The server antenna must be installed
to provide at least 20 cm separation
from the human body at all times.
This device contains licence-exempt
transmitter(s)/ receiver(s) that comply with
Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is
subject to the following two con- ditions:
ISED STATEMENT
WARNING: This is NOT a CONSUMER device. It is de-
signed for installation by an installer approved by an
ISED licensee. You MUST have an ISED LICENCE or
the express consent of an ISED licensee to operate
this device.
This device may operate in a xed l ocation only, for
in-building use.
In order to comply with ISED RF Exposure require-
ments:
[French: An de se conformer aux exigences d’exposition
RF ISED:
1. L’antenne du donneur doit être installée pour
fournir une séparation d’au moins 65 cm du
corps humain en tout temps.
2. L’antenne du serveur doit être installée pour
fournir une séparation d’au moins 20 cm du
corps humain en tout temps.
The Manufacturer’s rated output power of this equip-
ment is for single carrier operation. For situations
when multiple carrier signals are present, the rating
would have to be reduced by 3.5 dB, especially where
the output signal is re-radiated and can cause interfer-
ence to adjacent band users. This power reduction is to
be by means of input power or gain reduction and not
by an attenuator at the output of the device.
[FRENCH: La puissance de sortie nominale indiquée
par le fabricant pour cet appareil concerne son
fonctionnement avec porteuse unique. Pour des
appareils avec porteuses multiples, on doit réduire la
valeur nominale de 3,5dB, surtout si le signal de sortie
est retransmis et qu’il peut causer du brouillage aux
utilisateurs de bandes adjacentes. Une telle réduction
doit porter sur la puissance d’entrée ou sur le gain, et
ne doit pas se faire au moyen d’un atténuateur
raccordé à la sortie du dispositif.]
1. This device may not cause interference.
2. This device must accept any interference, in-
cluding interference that may cause undesired
operation of the device.
[French: L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développe-
ment économique Canada applicables aux ap-
pareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage ra-
dioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionne-
ment.]
CAN ICES-3 (A)/NMB-3(A)
Compliance Contact
In the event of regulatory compliance issue, please
contact Nextivity Inc. directly. Contact information is
available at www.nextivityinc.com.
Patents
This product is covered by Nextivity, Inc., US patents
and patents pending. Please refer to cel-.com for
details.
Copyright
Copyright © 2022 by Nextivity, Inc. All rights reserved.
Reproduction or media conversion by any means is
protected by copyright and may only occur with prior
written permission of Nextivity. Designed by Nextivity
in California.
Trademark
Cel-Fi and the Nextivity logo are trademarks of Nex-
tivity, Inc.
If you need help, visit: www.cel-.com/support.
1. The donor antenna must be installed
to provide at least 65 cm separation
from the human body at all times.
2. The server antenna must be installed
to provide at least 20 cm separation
from the human body at all times.
This device contains licence-exempt
transmitter(s)/ receiver(s) that comply with
Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is
subject to the following two con- ditions:
ISED STATEMENT
WARNING: This is NOT a CONSUMER device. It is de-
signed for installation by an installer approved by an
ISED licensee. You MUST have an ISED LICENCE or
the express consent of an ISED licensee to operate
this device.
This device may operate in a xed l ocation only, for
in-building use.
In order to comply with ISED RF Exposure require-
ments:
-
1
-
2
Nextivity L41-7EB Mode d'emploi
- Catégorie
- Antennes réseau
- Taper
- Mode d'emploi
dans d''autres langues
- English: Nextivity L41-7EB User guide
Autres documents
-
RETAIL AWARE MSNSR Manuel utilisateur
-
CEL-FI SOLO RED 0.5W ERCES Public Mode d'emploi
-
Softbank Robotics A00041301 Automatic Cleaning Machine Manuel utilisateur
-
Creative N400 Le manuel du propriétaire
-
Hansong(Nanjing) Technology XCO-CRESCENDOX Manuel utilisateur
-
SureCall SC-POLY-DT-O-KI Manuel utilisateur
-
SureCall SC-FlareDB Mode d'emploi
-
MartinLogan Unison Manuel utilisateur
-
Rotel T14 Le manuel du propriétaire
-
