Develco MGW211 Manuel utilisateur

Taper
Manuel utilisateur
eng
Power cable
Ethernet cable
Product label
Product label
Resetting
Reset the gateway to avoid abnormal behavior
by removing the power supply for a few minutes
before reapplying it. In case the gateway does
not start up, follow the steps below to reset the
gateway to the factory setting.
STEPS FOR RESETTING
1. Use a pen and hold down the reset button
as indicated in the picture.
Disposal
Dispose the product properly at the end of
life. This is electronic waste which should be
recycled.
This gateway optionally includes a Lithium
battery. Please dispose of the battery
according to your local regulations.
2. Release the pen again when the LED on the
front panel starts to ash continuously.
3. The system will reboot and after a few
minutes the application will be started again.
Getting started
1. Connect the power cable to the gateway.
2. Connect the power adapter to a wall socket.
3. Connect an Ethernet cable from the
gateway to an internet-connected home
router.
4. The LEDs on the front panel are turned on
when the system is booting.
5. The LEDs in the Ethernet connector
are turned on and the green LED starts
ashing indicating data communication.
6. After a few minutes, the application is
started and the system is ready for use.
Do not remove the product label as it
contains important information.
Product description
This all-in-one gateway connects smart devices
and provides you with monitoring and control
functionalities via your smart system. As the
gateway is simple to install, you can quickly
start to use your smart system and enjoy the
connected life.
Version 1.5
INSTALLATION MANUAL
MGW211 and MGW221
Squid.link 2B/2X
Precautions
a.
b.
c.
Insert sim card
If you have a single sim card and no battery
backup:
Simple insert the sim card into the card slot
on the bottom of the gateway.
If you have dual sim and/or battery backup:
1. Open the battery compartment of the
gateway with a screwdriver.
Battery replacement
If your gateway includes a battery backup, you
can replace the battery in the following way.
CAUTION: RISK OF EXPLOSION IF BATTERIES
ARE REPLACED BY AN INCORRECT
TYPE. DISPOSE OF THE BATTERIES IN
ACCORDANCE WITH INSTRUCTIONS.
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside
1. Open the battery compartment of the
gateway with a screwdriver.
2. Remove the battery from its place within
the compartment.
3. Disconnect the battery and connect the
new one. The gateway uses a Li Pol (3,8 V /
2000 mA) battery.
2. Remove the battery from the
compartment. It is not necessary to
disconnect the battery for this.
3. Insert one or two sim cards into the card
slots. If you have only one sim card, insert
it into the slot marked as 1.
4. Put the battery back into its place.
5. Close the battery compartment and
reattach the screw to fasten it.
d.
1
2
e. 4. Insert the new battery in its space in the
compartment and tuck the cables over or
under the battery.
1
2
f.
5. Close the battery compartment and
reattach the screw to fasten it.
g.
1
2
Other certications
Zigbee 3.0 certied.
CE certication
The CE mark axed to th is product conrms
its compliance with the European Directives
which apply to the product and, in particular, its
compliance with the harmonized standards and
specifications.
To comply with RF exposure requirements, a
minimum separation distance of 30cm must be
maintained between the user’s body and the handset,
including the antenna.
the radio equipment type [MGW211/MGW221] is in
compliance with Directive 2014/53/EU. The full text of
the EU declaration of conformity is available at the
Official Website.
IN ACCORDANCE WITH THE DIRECTIVES
Radio Equipment Directive (RED)
2014/53/EU
EMC Directive 2014/30/EU
RoHS Directive 2015/863/EU amending
2011/65/EU
Develco Products assumes no responsibility for
any errors, which may appear in this manual.
Furthermore, Develco Products reserves the
right to alter the hardware, software, and/
or specications detailed herein at any time
without notice, and Develco Products does
not make any commitment to update the
information contained herein. All the trademarks
listed herein are owned by their respective
owners.
Copyright © Develco Products A/S
All rights reserved.
Distributed by Develco Products A/S
Tangen 6
8200 Aarhus N
Denmark
www.develcoproducts.com
FCC Regulatory Compliance
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
Changes or modications not expressly
approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged
to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This equipment should be
installed and operated with minimum distance
20cm between the radiator and your body.
This transmitter must not be co-located
or operating in conjunction with any other
antenna or transmitter.
Français
Lémetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes:
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Cet équipement est conforme aux limites
d’exposition aux radiations IC CNR‐102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance minimale de 20cm entre le radiateur et
votre corps.
ISED Regulatory Compliance
English
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause undesired
operation of the device.
This equipment complies with IC RSS‐102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with minimum
distance 20cm between the radiator and your
body.
Wireless communication
Zigbee:
Frequency: 2.4 GHz(2405-2480MHz)
Output power: Up to +3.55 dBm “Declaration for
EU Compliance”
WLAN:
Frequency: 2.4 GHz(2412-2472MHz for
EU/2412-2462MHz for US)
Output power: Up to +17.16 dBm “Declaration for
EU Compliance”
Z-Wave:
Frequency: 868.4MHz/869.85MHz (for EU),
908.4MHz/916MHz (for US)
Output power: Up to +9.99 dBm “Declaration for
EU Compliance”
Wireless M-Bus:
Frequency: 868.98MHz
Output power: Up to +9.99 dBm “Declaration for
EU Compliance”
Bluetooth Low Energy:
Frequency: 2.4 GHz(2402-2480MHz)
Output power: Up to +4.35 dBm “Declaration for
EU Compliance”
  • Page 1 1
  • Page 2 2

Develco MGW211 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues