Toro 21in Power Clear Flex-Force Power System 60V MAX Snowthrower Manuel utilisateur

Form No. 3461-708 Rev B

21in Power Clear

®

Flex-Force Power

System

™

60V MAX Snowthrower39921 , 39921T

Lanzanieves Power Clear

®

de 53 cm (21")

con Flex-Force Power System

™

60 V MAX39921 , 39921T

Soufeuse à neige Power Clear

®

Flex-Force

Power System

™

60 V MAX de 53 cm (21 po)39921 , 39921T

www .T oro.com.

*3461-708*

Form No. 3461-705 Rev B

21in Power Clear

®

Flex-Force

Power System

®

60V MAX

Snowthrower

Model No. 39921 —Serial No. 400000000 and Up

Model No. 39921T —Serial No. 400000000 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3461-705*

For assistance, please see

www .T oro.com/support

for instructional videos

or contact 1-888-384-9939

before returning this

product.

W ARNING

CALIFORNIA

Proposition 65 W arning

The power cord on this product contains

lead, a chemical known to the State

of California to cause birth defects

or other reproductive harm. W ash

hands after handling.

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This machine is intended to be used by residential

homeowners. It is designed for removing snow from

patios, sidewalks, and small driveways. It is not

designed for removing materials other than snow ,

nor is it designed for clearing gravel surfaces. It is

designed to use Flex-Force 60V lithium-ion battery

packs. These battery packs are designed to be

charged only by Flex-Force 60V lithium-ion battery

chargers. Using this product for purposes other than

its intended use could prove dangerous to you and

bystanders.

Model 39921T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

g381459

Figure 1

1. Model and serial number location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in Mexico

Safety

READ ALL INSTRUCTIONS

W ARNING—When using an electrical machine,

basic safety precautions should always be followed

to reduce the risk of re, electric shock, or injury ,

including the following:

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Read and understand the contents of this

Operator ’ s Manual before you start the machine.

Ensure that everyone using this machine knows

how to use it, knows how to shut it of f quickly ,

and understands the warnings.

3. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

4. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

5. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

6. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders and children out of the

operating area.

2. Never allow children to operate the machine.

3. Do not operate the machine without all guards

and safety devices in place and functioning

properly on the machine.

4. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet that

is not 120V can cause a re or electric shock.

Do not plug the battery charger into an outlet

other than 120V .

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant rubber boots; and hearing

protection. T ie back long hair and do not wear

loose clothing or loose jewelry that can get

caught in moving parts.

III. Operation

1. Contact with the moving rotor will cause serious

injury . Keep your hands and feet away from all

moving parts of the machine. Keep clear of any

discharge opening.

2. Stay behind the handles and away from the

discharge opening while operating the machine.

3. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

4. Prevent unintentional starting—Ensure that the

electric-start button is removed from the ignition

before connecting the battery pack and handling

the machine.

5. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

6. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

7. Do not use the machine on a gravel surface.

8. Remove the battery pack and electric-start

button from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

3

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Operate the machine only in good visibility and

appropriate weather conditions.

12. Use extreme caution when reversing or pulling

the machine toward you.

13. Keep proper footing and balance at all times,

especially on slopes. Use extreme caution when

changing directions on slopes. Do not operate

the machine on exceedingly steep slopes. W alk,

never run with the machine.

14. When not actively clearing snow , disengage

power to the auger .

15. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Stop the machine when crossing gravel

surfaces.

16. Never operate the machine at high transport

speeds on slippery surfaces.

17. Exercise extreme caution when operating the

machine on or crossing drives, walks, or roads.

Stay alert for hidden hazards or traf c.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the electric-start button, remove the

battery pack, and wait for all movement to stop

before examining the machine for damage.

Make all necessary repairs before resuming

operation.

19. Shut of f the machine whenever you leave the

operating position for any reason.

20. Shut of f the machine before unclogging the

machine and always use a stick or a cleanout

tool to remove the clog.

21. Stop the machine and remove the electric-start

button before loading the machine for hauling.

22. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

23. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

24. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

Flex-Force battery pack only; using another

type of battery pack may cause a re or risk

of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

IV . Maintenance and Storage

1. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an Authorized

Service Dealer perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. When servicing the rotor , be aware that the rotor

can still move even though the power source

is of f.

5. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

6. Maintain the machine—Keep handles dry , clean,

and free from oil and grease. Keep guards

in place and in working order . Use identical

replacement parts only .

7. Check all fasteners at frequent intervals for

proper tightness to ensure that the machine is in

safe working condition.

8. Check the machine for damaged parts. Check

for misaligned and binding moving parts, broken

parts, mounting, and any other condition that

may af fect its operation. Unless indicated in the

instructions, have an Authorized Service Dealer

repair or replace a damaged guard or part.

9. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

10. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

1 1. When storing the machine for more than 30

days, refer to Storage ( page 17 ) for important

information.

4

12. Do not dispose of the battery in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal145-8251

145-8251

decal145-8252

145-8252

decal137-2257

137-2257

1. W arning—read the Operator ’ s Manual .

3. Thrown object hazard—keep bystanders away .

2. Cutting/dismemberment of hand hazard, impeller;

cutting/entanglement of foot hazard, auger—stay away from

moving parts; keep all guards and shields in place; shut of f

the engine and remove the key before leaving the machine;

read the Operator ’ s Manual before performing maintenance.

decal137-2258

137-2258

1. T o start the motor , bring the bail to the handle and press the

ignition button.

2. ECO

6

decal137-9463

137-9463

1. The battery pack is charging.

2. The battery pack is fully charged.

3. The battery pack is over or under the appropriate temperature range.

4. Battery pack charging fault

decal137-9462

137-9462

decal137-9461

137-9461

1. Battery charge status

decal147-9420

147-9420

decal137-9454

137-9454

1. Read the Operator ’ s

Manual .

3. Keep away from open re

or ames.

2. Call2Recycle

®

battery

recycling program

4. Do not expose to rain.

7

decal1 14-9035

1 14-9035

1. Cutting/dismemberment hazard of hand, impeller;

cutting/dismemberment hazard of foot, auger—do not

place your hand in the chute; remove the key and read the

Operator ’ s Manual before performing maintenance.

decal147-1787

147-1787

1. The combined Ah rating of

all installed batteries must

be greater than 4.0Ah to

start the machine, and

greater than 7.5Ah for best

runtime and operation.

2. Read the Operator's

Manual .

8

Setup

Important: The battery pack is not fully charged

when you purchase it. Before using the machine

for the rst time, refer to Charging the Battery

Pack ( page 14 ) .

1

Mounting the Battery

Charger (Optional)

No Parts Required

Procedure

If desired, mount the battery charger securely on a

wall using the wall-mount key holes on the back of

the charger .

Mount it indoors (such as a garage or other dry place),

near a power outlet, and out of the reach of children.

Refer to Figure 2 for assistance in mounting the

charger .

Slide the charger over the appropriately positioned

hardware to secure the charger in place (hardware

not included).

g290534

Figure 2

9

2

Unfolding the Handle

Parts needed for this procedure:

2 Handle lock

2 Handle knob

Procedure

g389401

3

Installing the Discharge Chute

Parts needed for this procedure:

1 Discharge chute assembly

3 Hex washer head screw

1

Chute handle

Procedure

g291515

10

Product Overview

g381633

Figure 5

1. Discharge chute 6. Headlight

2. Chute deector 7. ECO switch

3. Chute-deector trigger

8. Electric-start button

4. Chute handle

9. Bail

5. Battery-compartment lid 10. Rotor blades

g292995

Figure 6

1. Battery charger Model

88602 (included with

Model 39921)

2. Battery pack Model 88625

and 88675 (included with

Model 39921)

Specications

Battery Pack

Model 88625 88675

2.5 Ah 7.5 AhBattery pack capacity

135 Wh 405 Wh

Battery manufacturer rating = 60V maximum and 54V nominal.

Actual voltage varies with load.

Battery Charger

Model 88602

T ype

60V MAX Lithium-Ion Battery Charger

Input

120V AC ~2A, 60Hz

Output 60V DC 2.0A MAX

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the machine at

-30°C (-22°F) to 23°C (73°F)*

Store the machine at -30°C (-22°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the machine, battery pack, and battery charger

in an enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories may be available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous, and such use could void the

product warranty .

1 1

Operation

Installing the Battery

Pack(s)

Important: Use a battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 1 1 ) .

1. Make sure that the vents on the battery are clear

of any dust and debris.

2. Lift up the battery-compartment lid (A of Figure

7).

3. Line up the cavity in the battery pack with the

tongue on the machine and slide the battery

pack into the compartment until it locks into

place (B of Figure 7 ).

4. Close the battery-compartment lid (C of Figure

7).

Note: Ensure that the battery-compartment lid

is completely closed and snapped into place

before starting the machine.

g381640

Figure 7

Starting the Machine

1. Ensure that the battery pack (or battery packs)

are installed in the machine; refer to Installing

the Battery Pack(s) ( page 12 ) .

2. Insert the electric-start button into the electric

starter (A of Figure 8 ).

3. Squeeze the bail and hold it to the handle (B

and C of Figure 8 ).

Note: When you squeeze the bail, the lights

turn on and the battery-charge indicator lights on

the battery illuminate.

4. Press the electric-start button until the motor

starts (D of Figure 8 ).

g288479

Figure 8

Note: This is a ground-engaging machine; rotor

contact with the ground is intentional and propels the

machine forward.

12

Activating ECO Mode

Using ECO mode may extend battery life by reducing

rotor speed; use ECO mode whenever you are

moving snow a short distance. Activate ECO mode

using the ECO switch as shown in Figure 5 .

g318457

Figure 9

1. T urn ECO mode on 2. T urn ECO mode of f

Shutting Off the Machine

1. Release the bail (A of Figure 10 ).

2. Remove the electric-start button from the electric

starter (B of Figure 10 ).

3. Remove the battery pack(s); refer to Removing

the Battery Pack(s) from the Machine ( page 13 ) .

Note: Whenever you are not using the

appliance, remove the battery pack(s).

g247446

Figure 10

Removing the Battery

Pack(s) from the Machine

1. Lift up the battery-compartment lid.

2. Press the battery pack-latch to release the

battery pack(s) and remove the battery pack(s).

3. Close the battery-compartment lid.

Preventing Freeze-up after

Use

•Let the motor run for a few minutes to prevent

moving parts from freezing. Shut of f the machine,

wait for all moving parts to stop, and remove ice

and snow from the machine.

•Clean of f any snow and ice from the base of the

chute.

•Rotate the discharge chute left and right to free

it from any ice buildup.

•In snowy and cold conditions, some controls and

moving parts may freeze. Do not use excessive

force when trying to operate frozen controls. If you

have dif culty operating any control or part, start

the machine and let it run for a few minutes.

13

Charging the Battery Pack

Important: The battery pack is not fully charged

when you purchase it. Before using the tool for

the rst time, place the battery pack in the charger

and charge it until the LED display indicates the

battery pack is fully charged. Read all safety

precautions.

Important: Charge the battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 1 1 ) .

Note: At any time, press the battery-charge-indicator

button on the battery pack to display the current

charge (LED indicators).

1. Ensure that the vents on the battery charger are

clear of any dust and debris.

g473274

Figure 1 1

1. Battery pack cavity 5. Handle

2. Battery pack terminals

6. Charger LED indicator

light

3. Battery-charge-indicator

button

7. Charger venting areas

4. LED indicators (current

charge)

2. Line up the cavity in the battery pack ( Figure 1 1 )

with the tongue on the charger .

3. Slide the battery pack into the charger until it is

fully seated ( Figure 1 1 ).

4. T o remove the battery pack, slide the battery

backward out of the charger .

5. Refer to the following table to interpret the LED

indicator light on the battery charger .

Indicator

light

Indicates

Of f

No battery pack inserted

Green

blinking

Battery pack is charging

Green

Battery pack is charged

Red

Battery pack and/or battery charger is over or under

the appropriate temperature range

Red

blinking

Battery pack charging fault*

*Refer to T roubleshooting ( page 18 ) for more

information.

Important: The battery can be left on the charger

for short periods between uses.

If the battery will not be used for longer periods,

remove the battery from the charger; refer to

Storage ( page 17 ) .

14

Adjusting the Discharge

Chute and Chute Deector

T o adjust the discharge chute, move the chute handle.

T o adjust the chute deector (and therefore the height

of the snow stream), squeeze the trigger and raise or

lower the chute deector ( Figure 12 ).

g278630

Figure 12

1. Chute handle

2. T rigger

W ARNING

A gap between the discharge chute and the

chute deector may allow the machine to

throw snow and objects in the direction of the

operator . Thrown objects could cause serious

personal injury .

• Do not force the chute deector too far

forward so that a gap appears between the

discharge chute and chute deector .

• Do not adjust the chute deector with the

power control bar engaged. Release the

power control bar before adjusting the

chute deector .

Clearing a Clogged

Discharge Chute

If the machine is running but there is no snow coming

out of the discharge chute, the discharge chute may

be clogged.

W ARNING

Contacting a rotating rotor with your hands

inside the discharge chute could cause

serious personal injury .

Never use your hands to clean out the

discharge chute.

1. Shut of f the machine, remove the electric-start

button, and remove the battery pack.

2. W ait 10 seconds to ensure that the rotor blades

have stopped rotating.

3. Always use a clean-out tool, not your hands, to

clear the chute.

Operating T ips

W ARNING

The rotor can throw stones, toys, and other

foreign objects and cause serious personal

injury to you or bystanders.

• Keep the area to be cleared free of all

objects that the rotor blades could pick up

and throw .

• Keep all children and pets away from the

area of operation.

•Remove the snow as soon as possible after it falls.

•Push the machine forward, but allow it to work at

its own pace.

•Overlap each swath to ensure complete snow

removal.

•Discharge the snow downwind whenever possible.

•If the machine does not propel itself forward on

slippery surfaces or in heavy snow , push forward

on the handle, but allow the machine to work at

its own pace.

•The machine may leave rubber marks on new

brushed or light-colored concrete. T est on an

inconspicuous location before use. These marks

are not permanent.

15

Maintenance

Stop the machine, remove the electric-start button,

remove the battery pack from the machine, and wait

for all movement to stop before adjusting, servicing,

cleaning, or storing the machine.

Inspecting the Rotor Blades

Service Interval : Y early —Inspect the rotor blades

and have an Authorized Service

Dealer replace the rotor blades and

scraper if necessary .

Before each session, inspect the rotor blades for

wear . When a rotor-blade edge has worn down to

the wear-indicator hole, have an Authorized Service

Dealer replace the rotor blades and the scraper

(Figure 13 ).

g01 1544

Figure 13

1. The wear-indicator hole is

intact; you do not need to

replace the rotor blades.

2. The wear-indicator hole is

exposed; replace the rotor

blades and scraper .

16

Storage

Important: Store the machine, battery pack, and

charger only in temperatures that are within the

appropriate range; refer to Specications ( page

1 1 ) .

Important: If you are storing the battery pack

for the off-season, charge it until 2 or 3 LED

indicators turn green on the battery . Do not store

a fully charged or fully depleted battery . When

you are ready to use the machine again, charge

the battery pack until the left indicator light turns

green on the charger or all 4 LED indicators turn

green on the battery .

•Disconnect the product from the power supply

(i.e., remove the plug from the power supply or the

battery pack) and check for damage after use.

•Clean all foreign material from the product.

•Do not store the tool with the battery pack installed.

•When not in use, store the machine, battery pack,

and battery charger out of the reach of children.

•Keep the machine, battery pack, and battery

charger away from corrosive agents, such as

garden chemicals and de-icing salts.

•T o reduce the risk of serious personal injury , do

not store the battery pack outside or in vehicles.

•Store the machine, battery pack, and battery

charger in an enclosed clean, dry area.

Preparing the Battery Pack

for Recycling

Important: Upon removal, cover the terminals of

the battery pack with heavy-duty adhesive tape.

Do not attempt to destroy or disassemble the

battery pack or remove any of its components.

Lithium-ion battery packs labeled with the

Call2Recycle seal can be recycled at any

participating retailer or battery recycling

facility in the Call2Recycle program (US

and Canada only). T o locate a participating

retailer or facility closest to you, please call

1-800-822-8837 or visit www .call2recycle.org.

If you cannot locate a participating retailer or

facility nearby , or if your rechargeable battery

is not labeled with the Call2Recycle seal,

please contact your local municipality for more

information on how to responsibly recycle the

battery . If you are located outside of the US

and Canada, please contact your authorized

T oro distributor .

17

T roubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work

must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the

problem yourself.

Problem

Possible Cause Corrective Action

1. The battery pack is low on charge.

1. Charge the battery pack.

2. The battery is not fully installed in the

machine.

2. Remove and then reseat the battery

into the machine, making sure that it is

fully installed and latched.

3. The battery pack is over or under the

appropriate temperature range.

3. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

4. The battery pack has exceeded high

amperage limits.

4. Release the trigger , then press the

trigger switch.

5. There is moisture on the leads of the

battery pack.

5. Allow the battery pack to dry or wipe it

dry .

6. The battery pack is damaged. 6. Replace the battery pack.

The machine does not run or does not run

continuously .

7. There is another electrical problem

with the machine.

7. Contact your Authorized Service

Dealer .

1. The battery pack charge capacity is

too low .

1. Remove the battery pack from the

machine and fully charge the battery

pack.

The machine does not reach full power .

2. The air vents are blocked.

2. Clean the air vents.

1. The machine is overloaded.

1. Push the machine with less force, or

at a slower pace.

2. Y ou are trying to remove too much

snow per swath.

2. Reduce the amount of snow removed

per swath.

3. Y ou are trying to remove extremely

heavy or wet snow .

3. Do not overload the machine with

extremely heavy or wet snow .

4. The discharge chute is plugged. 4. Unclog the discharge chute.

5. The auger/impeller drive belt is loose

or is of f the pulley .

5. Install and/or adjust the auger/impeller

drive belt; refer to www .T oro.com

for servicing information or take the

machine to an Authorized Service

Dealer .

The machine runs, but the machine

discharges snow poorly or not at all.

6. The auger/impeller drive belt is worn

or broken.

6. Replace the auger/impeller drive belt;

refer to www .T oro.com for servicing

information or take the machine to an

Authorized Service Dealer .

1. The battery pack is over or under the

appropriate temperature range.

1. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

The battery pack loses charge quickly .

2. The machine is overloaded.

2. Push the machine with less force.

1. The battery charger is over or under

the appropriate temperature range.

1. Unplug the battery charger and move

it to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

The battery charger is not working.

2. The outlet that the battery charger is

plugged into does not have power .

2. Contact your licensed electrician to

repair the outlet.

The LED indicator light on the battery

charger is red.

1. The battery charger and/or battery

pack is over or under the appropriate

temperature range.

1. Unplug the battery charger and move

the battery charger and battery pack

to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

18

La page charge ...

Toro 21in Power Clear Flex-Force Power System 60V MAX Snowthrower Manuel utilisateur

Toro 21in Power Clear Flex-Force Power System 60V MAX Snowthrower Manuel utilisateur

dans d''autres langues

Documents connexes