Toro 21in Power Clear Flex-Force Power System 60V MAX Commercial Snowthrower Manuel utilisateur

Marque: Toro

Modèle: 21in Power Clear Flex-Force Power System 60V MAX Commercial Snowthrower

Taper: Manuel utilisateur

Form No. 3465-559 Rev A

21in Power Clear

Flex-Force Power System

™

60V

MAX Commercial Snowthrower

39922T

Lanzanieves comercial Power Clear

de 53 cm (21")

con Flex-Force Power System

™

60 V MAX

39922T

Soufeuse à neige commerciale Power Clear

Flex-Force Power System

™

60 V MAX de 53 cm (21 po)

39922T

www .T oro.com.

*3465-559*

Form No. 3465-556 Rev A

21in Power Clear

Flex-Force

Power System

™

60V MAX

Commercial Snowthrower

Model No. 39922T —Serial No. 414441380 and Up

Original Instructions (EN)

*3465-556*

For assistance, please see

www .T oro.com/support

for instructional videos

or contact 1-888-384-9939

before returning this

product.

W ARNING

CALIFORNIA

Proposition 65 W arning

Use of this product may cause exposure

to chemicals known to the State of

California to cause cancer , birth defects,

or other reproductive harm.

Introduction

This machine is intended to be used by residential

homeowners. It is designed for removing snow from

patios, sidewalks, and small driveways. It is not

designed for removing materials other than snow ,

nor is it designed for clearing gravel surfaces. It is

designed to use T oro 60V lithium-ion battery packs.

These battery packs are designed to be charged only

by T oro 60V lithium-ion battery chargers. Using this

product for purposes other than its intended use could

prove dangerous to you and bystanders.

Model 39922T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for more information, including

safety tips, training materials, accessory information,

help nding a dealer , or to register your product.

Whenever you need service, genuine T oro parts, or

additional information, contact an Authorized Service

Dealer or T oro Customer Service and have the model

and serial numbers of your product ready . Figure 1

identies the location of the model and serial numbers

on the product. W rite the numbers in the space

provided.

g381459

Figure 1

1. Model and serial number location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

Printed in Mexico

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Safety

READ ALL INSTRUCTIONS

W ARNING—When using an electrical machine,

basic safety precautions should always be followed

to reduce the risk of re, electric shock, or injury ,

including the following:

I. T raining

1. The operator of the machine is responsible for

any accidents or hazards occurring to others or

their property .

2. Read and understand the contents of this

Operator ’ s Manual before you start the machine.

Ensure that everyone using this machine knows

how to use it, knows how to shut it of f quickly ,

and understands the warnings.

3. Do not allow children to use or play with the

machine, battery pack, or the battery charger;

local regulations may restrict the age of the

operator .

4. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

5. Before using the machine, battery pack, and

battery charger , read all the instructions and

cautionary markings on these products.

6. Become familiar with the controls and proper

use of the machine, battery pack, and battery

charger .

II. Preparation

1. Keep bystanders and children out of the

operating area.

2. Never allow children to operate the machine.

3. Do not operate the machine without all guards

and safety devices in place and functioning

properly on the machine.

4. Inspect the area where you will use the machine

and remove all objects that could interfere with

the operation of the machine or that the machine

could throw .

5. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

6. Plugging the battery charger into an outlet that

is not 120 V can cause a re or electric shock.

Do not plug the battery charger into an outlet

other than 120 V .

7. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

8. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

9. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

1 type of battery pack may create a risk of re

when used with another battery pack.

10. Charge the battery pack in a well-ventilated area

only .

1 1. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

12. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant rubber boots; and hearing

protection. T ie back long hair and do not wear

loose clothing or loose jewelry that can get

caught in moving parts.

III. Operation

1. Contact with the moving rotor will cause serious

injury . Keep your hands and feet away from all

moving parts of the machine. Keep clear of any

discharge opening.

2. Stay behind the handles and away from the

discharge opening while operating the machine.

3. Using this machine for purposes other than its

intended use could prove dangerous to you and

bystanders.

4. Prevent unintentional starting—Ensure that the

electric-start button is removed from the ignition

before connecting the battery pack and handling

the machine.

5. Use your full attention while operating the

machine. Do not engage in any activity that

causes distractions; otherwise, injury or property

damage may occur .

6. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

7. Do not use the machine on a gravel surface.

8. Remove the battery pack and electric-start

button from the machine whenever you leave it

unattended or before changing accessories.

9. Do not force the machine—Allow the machine to

do the job better and safer at the rate for which it

was designed.

10. Stay alert—W atch what you are doing and use

common sense when operating the machine.

Do not use the machine while ill, tired, or under

the inuence of alcohol or drugs.

1 1. Operate the machine only in good visibility and

appropriate weather conditions.

12. Use extreme caution when reversing or pulling

the machine toward you.

13. Keep proper footing and balance at all times,

especially on slopes. Use extreme caution when

changing directions on slopes. Do not operate

the machine on exceedingly steep slopes. W alk,

never run with the machine.

14. When not actively clearing snow , disengage

power to the auger .

15. Do not direct the discharge material toward

anyone. A void discharging material against a

wall or obstruction; material may ricochet toward

you. Stop the machine when crossing gravel

surfaces.

16. Never operate the machine at high transport

speeds on slippery surfaces.

17. Exercise extreme caution when operating the

machine on or crossing drives, walks, or roads.

Stay alert for hidden hazards or traf c.

18. If the machine strikes an object or starts to

vibrate, immediately shut of f the machine,

remove the electric-start button, remove the

battery pack, and wait for all movement to stop

before examining the machine for damage.

Make all necessary repairs before resuming

operation.

19. Shut of f the machine whenever you leave the

operating position for any reason.

20. Shut of f the machine before unclogging the

machine and always use a stick or a cleanout

tool to remove the clog.

21. Stop the machine and remove the electric-start

button before loading the machine for hauling.

22. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

23. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

24. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

IV . Maintenance and Storage

1. Stop the machine, remove the electric-start

button, remove the battery pack from the

machine, and wait for all movement to stop

before adjusting, servicing, cleaning, or storing

the machine.

2. Do not attempt to repair the machine except as

indicated in the instructions. Have an Authorized

Service Dealer perform service on the machine

using identical replacement parts.

3. W ear gloves and eye protection when servicing

the machine.

4. When servicing the rotor , be aware that the rotor

can still move even though the power source

is of f.

5. For best performance, use only genuine T oro

replacement parts and accessories. Other

replacement parts and accessories could be

dangerous, and such use could void the product

warranty .

6. Maintain the machine—Keep handles dry , clean,

and free from oil and grease. Keep guards

in place and in working order . Use identical

replacement parts only .

7. Check all fasteners at frequent intervals for

proper tightness to ensure that the machine is in

safe working condition.

8. Check the machine for damaged parts. Check

for misaligned and binding moving parts, broken

parts, mounting, and any other condition that

may af fect its operation. Unless indicated in the

instructions, have an Authorized Service Dealer

repair or replace a damaged guard or part.

9. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

10. When you are not using the machine, store it

indoors in a dry , secure place out of the reach

of children.

1 1. When storing the machine for more than 30

days, refer to Storage ( page 14 ) for important

information.

12. Do not dispose of the battery in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

SA VE THESE

INSTRUCTIONS

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal161-2157

161-2157

decal137-2257

137-2257

1. W arning—read the Operator ’ s Manual .

3. Thrown object hazard—keep bystanders away .

2. Cutting/dismemberment of hand hazard, impeller;

cutting/entanglement of foot hazard, auger—stay away from

moving parts; keep all guards and shields in place; shut of f

the engine and remove the key before leaving the machine;

read the Operator ’ s Manual before performing maintenance.

decal137-2258

137-2258

1. T o start the motor , bring the bail to the handle and press the

ignition button.

2. ECO

decal147-9420

147-9420

decal1 14-9035

1 14-9035

1. Cutting/dismemberment hazard of hand, impeller;

cutting/dismemberment hazard of foot, auger—do not

place your hand in the chute; remove the key and read the

Operator ’ s Manual before performing maintenance.

decal147-1787

147-1787

1. The combined Ah rating of

all installed batteries must

be greater than 4.0Ah to

start the machine, and

greater than 7.5Ah for best

runtime and operation.

2. Read the Operator's

Manual .

Setup

Unfolding the Handle

Parts needed for this procedure:

2 Handle lock

2 Handle knob

Procedure

g389401

Installing the Discharge Chute

Parts needed for this procedure:

1 Discharge chute assembly

3 Hex washer head screw

Chute handle

Procedure

g291515

Product Overview

g381633

Figure 5

1. Discharge chute 6. Headlight

2. Chute deector 7. ECO switch

3. Chute-deector trigger

8. Electric-start button

4. Chute handle

9. Bail

5. Battery-compartment lid 10. Rotor blades

Specications

Battery Charger

Model 39922T

Rated V oltage

60V DC maximum, 54 VDC nominal

usage

Charger T ype

T oro 60V lithium-ion chargers

Battery T ype T oro 60V lithium-ion batteries

Appropriate T emperature Ranges

Charge/store the battery pack

5°C (41°F) to 40°C (104°F)*

Use the machine at

-30°C (-22°F) to 23°C (73°F)*

Store the machine at -30°C (-22°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the machine, battery pack, and battery charger

in an enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories may be available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous, and such use could void the

product warranty .

Operation

Installing the Battery

Pack(s)

Important: Use a battery pack only in

temperatures that are within the appropriate

range; refer to Specications ( page 9 ) .

1. Make sure that the vents on the battery are clear

of any dust and debris.

2. Lift up the battery-compartment lid (A of Figure

6).

3. Line up the cavity in the battery pack with the

tongue on the machine and slide the battery

pack into the compartment until it locks into

place (B of Figure 6 ).

4. Close the battery-compartment lid (C of Figure

6).

Note: Ensure that the battery-compartment lid

is completely closed and snapped into place

before starting the machine.

g381640

Figure 6

Starting the Machine

1. Ensure that the battery pack (or battery packs)

are installed in the machine; refer to Installing

the Battery Pack(s) ( page 10 ) .

2. Insert the electric-start button into the electric

starter (A of Figure 7 ).

3. Squeeze the bail and hold it to the handle (B

and C of Figure 7 ).

Note: When you squeeze the bail, the lights

turn on and the battery-charge indicator lights on

the battery illuminate.

4. Press the electric-start button until the motor

starts (D of Figure 7 ).

g288479

Figure 7

Note: This is a ground-engaging machine; rotor

contact with the ground is intentional and propels the

machine forward.

Activating ECO Mode

Using ECO mode may extend battery life by reducing

rotor speed; use ECO mode whenever you are

moving snow a short distance. Activate ECO mode

using the ECO switch as shown in Figure 5 .

g318457

Figure 8

1. T urn ECO mode on 2. T urn ECO mode of f

Shutting Off the Machine

1. Release the bail (A of Figure 9 ).

2. Remove the electric-start button from the electric

starter (B of Figure 9 ).

3. Remove the battery pack(s); refer to Removing

the Battery Pack(s) from the Machine ( page 1 1 ) .

Note: Whenever you are not using the

appliance, remove the battery pack(s).

g247446

Figure 9

Removing the Battery

Pack(s) from the Machine

1. Lift up the battery-compartment lid.

2. Press the battery pack-latch to release the

battery pack(s) and remove the battery pack(s).

3. Close the battery-compartment lid.

Preventing Freeze-up after

Use

•Let the motor run for a few minutes to prevent

moving parts from freezing. Shut of f the machine,

wait for all moving parts to stop, and remove ice

and snow from the machine.

•Clean of f any snow and ice from the base of the

chute.

•Rotate the discharge chute left and right to free

it from any ice buildup.

•In snowy and cold conditions, some controls and

moving parts may freeze. Do not use excessive

force when trying to operate frozen controls. If you

have dif culty operating any control or part, start

the machine and let it run for a few minutes.

1 1

Adjusting the Discharge

Chute and Chute Deector

T o adjust the discharge chute, move the chute handle.

T o adjust the chute deector (and therefore the height

of the snow stream), squeeze the trigger and raise or

lower the chute deector ( Figure 10 ).

g278630

Figure 10

1. Chute handle

2. T rigger

W ARNING

A gap between the discharge chute and the

chute deector may allow the machine to

throw snow and objects in the direction of the

operator . Thrown objects could cause serious

personal injury .

• Do not force the chute deector too far

forward so that a gap appears between the

discharge chute and chute deector .

• Do not adjust the chute deector with the

power control bar engaged. Release the

power control bar before adjusting the

chute deector .

Clearing a Clogged

Discharge Chute

If the machine is running but there is no snow coming

out of the discharge chute, the discharge chute may

be clogged.

W ARNING

Contacting a rotating rotor with your hands

inside the discharge chute could cause

serious personal injury .

Never use your hands to clean out the

discharge chute.

1. Shut of f the machine, remove the electric-start

button, and remove the battery pack.

2. W ait 10 seconds to ensure that the rotor blades

have stopped rotating.

3. Always use a clean-out tool, not your hands, to

clear the chute.

Operating T ips

W ARNING

The rotor can throw stones, toys, and other

foreign objects and cause serious personal

injury to you or bystanders.

• Keep the area to be cleared free of all

objects that the rotor blades could pick up

and throw .

• Keep all children and pets away from the

area of operation.

•Remove the snow as soon as possible after it falls.

•Push the machine forward, but allow it to work at

its own pace.

•Overlap each swath to ensure complete snow

removal.

•Discharge the snow downwind whenever possible.

•If the machine does not propel itself forward on

slippery surfaces or in heavy snow , push forward

on the handle, but allow the machine to work at

its own pace.

•The machine may leave rubber marks on new

brushed or light-colored concrete. T est on an

inconspicuous location before use. These marks

are not permanent.

Maintenance

Stop the machine, remove the electric-start button,

remove the battery pack from the machine, and wait

for all movement to stop before adjusting, servicing,

cleaning, or storing the machine.

Inspecting the Rotor Blades

Service Interval : Y early —Inspect the rotor blades

and have an Authorized Service

Dealer replace the rotor blades and

scraper if necessary .

Before each session, inspect the rotor blades for

wear . When a rotor-blade edge has worn down to

the wear-indicator hole, have an Authorized Service

Dealer replace the rotor blades and the scraper

(Figure 1 1 ).

g01 1544

Figure 1 1

1. The wear-indicator hole is

intact; you do not need to

replace the rotor blades.

2. The wear-indicator hole is

exposed; replace the rotor

blades and scraper .

Storage

Important: Store the machine, battery pack, and

charger only in temperatures that are within the

appropriate range; refer to Specications ( page 9 ) .

Important: If you are storing the battery pack

for the off-season, charge it until 2 or 3 LED

indicators turn green on the battery . Do not store

a fully charged or fully depleted battery . When

you are ready to use the machine again, charge

the battery pack until the left indicator light turns

green on the charger or all 4 LED indicators turn

green on the battery .

•Disconnect the product from the power supply

(i.e., remove the plug from the power supply or the

battery pack) and check for damage after use.

•Clean all foreign material from the product.

•Do not store the tool with the battery pack installed.

•When not in use, store the machine, battery pack,

and battery charger out of the reach of children.

•Keep the machine, battery pack, and battery

charger away from corrosive agents, such as

garden chemicals and de-icing salts.

•T o reduce the risk of serious personal injury , do

not store the battery pack outside or in vehicles.

•Store the machine, battery pack, and battery

charger in an enclosed clean, dry area.

T roubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work

must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the

problem yourself.

Problem

Possible Cause Corrective Action

1. The battery pack is low on charge.

1. Charge the battery pack.

2. The battery is not fully installed in the

machine.

2. Remove and then reseat the battery

into the machine, making sure that it is

fully installed and latched.

3. The battery pack is over or under the

appropriate temperature range.

3. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

4. The battery pack has exceeded high

amperage limits.

4. Release the trigger , then press the

trigger switch.

5. There is moisture on the leads of the

battery pack.

5. Allow the battery pack to dry or wipe it

dry .

6. The battery pack is damaged. 6. Replace the battery pack.

The machine does not run or does not run

continuously .

7. There is another electrical problem

with the machine.

7. Contact your Authorized Service

Dealer .

1. The battery pack charge capacity is

too low .

1. Remove the battery pack from the

machine and fully charge the battery

pack.

The machine does not reach full power .

2. The air vents are blocked.

2. Clean the air vents.

1. The machine is overloaded.

1. Push the machine with less force, or

at a slower pace.

2. Y ou are trying to remove too much

snow per swath.

2. Reduce the amount of snow removed

per swath.

3. Y ou are trying to remove extremely

heavy or wet snow .

3. Do not overload the machine with

extremely heavy or wet snow .

4. The discharge chute is plugged. 4. Unclog the discharge chute.

5. The auger/impeller drive belt is loose

or is of f the pulley .

5. Install and/or adjust the auger/impeller

drive belt; refer to www .T oro.com

for servicing information or take the

machine to an Authorized Service

Dealer .

The machine runs, but the machine

discharges snow poorly or not at all.

6. The auger/impeller drive belt is worn

or broken.

6. Replace the auger/impeller drive belt;

refer to www .T oro.com for servicing

information or take the machine to an

Authorized Service Dealer .

1. The battery pack is over or under the

appropriate temperature range.

1. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

The battery pack loses charge quickly .

2. The machine is overloaded.

2. Push the machine with less force.

1. The battery charger is over or under

the appropriate temperature range.

1. Unplug the battery charger and move

it to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

The battery charger is not working.

2. The outlet that the battery charger is

plugged into does not have power .

2. Contact your licensed electrician to

repair the outlet.

The LED indicator light on the battery

charger is red.

1. The battery charger and/or battery

pack is over or under the appropriate

temperature range.

1. Unplug the battery charger and move

the battery charger and battery pack

to a place where it is dry and the

temperature is between 5°C (41°F)

and 40°C (104°F).

Problem

Possible Cause Corrective Action

1. There is an error in the communication

between the battery pack and the

charger .

1. Remove the battery pack from the

battery charger , unplug the battery

charger from the outlet, and wait 10

seconds. Plug the battery charger into

the outlet again and place the battery

pack on the battery charger . If the LED

indicator light on the battery charger is

still blinking red, repeat this procedure

again. If the LED indicator light on

the battery charger is still blinking red

after 2 attempts, properly dispose of

the battery pack at a battery recycling

facility .

The LED indicator light on the battery

charger is blinking red.

2. The battery pack is weak.

2. Contact your authorized service dealer

if the battery is in warranty , or properly

dispose of the battery pack at a battery

recycling facility .

1. The battery pack is not charged.

1. Remove the battery pack from the

machine and charge it.

2. The machine is overloaded. 2. W alk at a slower pace while clearing

snow .

The machine is producing a beeping

sound.

3. There is another electrical problem

with the machine.

3. Attempt the other troubleshooting

actions, if the alarm still sounds,

contact an Authorized Service Dealer .

California Proposition 65 W arning Information

What is this warning?

Y ou may see a product for sale that has a warning label like the following:

W ARNING: Cancer and Reproductive Harm—www .p65W arnings.ca.gov .

What is Prop 65?

Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into

California. It mandates that the Governor of California maintain and publish a list of chemicals known to cause cancer , birth defects, and/or other

reproductive harm. The list, which is updated annually , includes hundreds of chemicals found in many everyday items. The purpose of Prop 65 is to

inform the public about exposure to these chemicals.

Prop 65 does not ban the sale of products containing these chemicals but instead requires warnings on any product, product packaging, or literature with

the product. Moreover , a Prop 65 warning does not mean that a product is in violation of any product safety standards or requirements. In fact, the

California government has claried that a Prop 65 warning “is not the same as a regulatory decision that a product is ‘safe’ or ‘unsafe.’” Many of these

chemicals have been used in everyday products for years without documented harm. For more information, go to https://oag.ca.gov/prop65/faqs-view-all .

A Prop 65 warning means that a company has either (1) evaluated the exposure and has concluded that it exceeds the “no signicant risk level”; or (2)

has chosen to provide a warning based on its understanding about the presence of a listed chemical without attempting to evaluate the exposure.

Does this law apply everywhere?

Prop 65 warnings are required under California law only . These warnings are seen throughout California in a wide range of settings, including but not

limited to restaurants, grocery stores, hotels, schools, and hospitals, and on a wide variety of products. Additionally , some online and mail order

retailers provide Prop 65 warnings on their websites or in catalogs.

How do the California warnings compare to federal limits?

Prop 65 standards are often more stringent than federal and international standards. There are various substances that require a Prop 65 warning

at levels that are far lower than federal action limits. For example, the Prop 65 standard for warnings for lead is 0.5 μg/day , which is well below

the federal and international standards.

Why don’t all similar products carry the warning?

•Products sold in California require Prop 65 labelling while similar products sold elsewhere do not.

•A company involved in a Prop 65 lawsuit reaching a settlement may be required to use Prop 65 warnings for its products, but other companies

making similar products may have no such requirement.

•The enforcement of Prop 65 is inconsistent.

•Companies may elect not to provide warnings because they conclude that they are not required to do so under Prop 65; a lack of warnings for a

product does not mean that the product is free of listed chemicals at similar levels.

Why does T oro include this warning?

T oro has chosen to provide consumers with as much information as possible so that they can make informed decisions about the products they buy and

use. T oro provides warnings in certain cases based on its knowledge of the presence of one or more listed chemicals without evaluating the level of

exposure, as not all the listed chemicals provide exposure limit requirements. While the exposure from T oro products may be negligible or well within the

“no signicant risk” range, out of an abundance of caution, T oro has elected to provide the Prop 65 warnings. Moreover , if T oro does not provide these