Bolens 11A-549Q565 Le manuel du propriétaire

Marque: Bolens

Modèle: 11A-549Q565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

PRINTED IN U.S.A. MTD Products Ltd., P. O. Box 1386, KITCHENER, ONTARIO N2G 4J1

OPERATOR’S MANUAL

IMPORTANT:

READ SAFETY RULES AND INSTRUCTIONS

CAREFULLY BEFORE OPERATING EQUIPMENT.

Safety • Setup • Adjustments • Operation • Maintenance • Troubleshooting • Parts Lists • Warranty

21” Rotary Mower — Model Series 540

1/8/09

769-04746

Finding and Recording Model Number

Table of Contents

BEFORE YOU START ASSEMBLING

YOUR NEW EQUIPMENT,

please locate the model plate on the equipment and copy the

model number and the serial number to the sample model

plate provided to the right. You can locate the model plate by

standing at the operating position and looking down at the rear

of the machine.

This Operator’s Manual is an important part of your new equipment. It will help you assemble,

prepare and maintain the unit for best performance. Please read and understand what it says.

Slope Gauge........................................................ 3

Safe Operation Practices ................................... 4

Safety Symbols ................................................... 7

Set-Up & Adjustments ........................................ 8

Operation ........................................................... 10

Maintenance ...................................................... 12

Off-Season Storage .......................................... 13

Trouble Shooting .............................................. 14

Warranty ............................................................ 15

Illustrated Parts Lists ....................................... 16

Please do

NOT

return the unit to the retailer from which it was purchased,

without rst contacting Customer Support.

Customer Support

If you have difficulty assembling this product or have any questions regarding the controls, operation or maintenance of this unit,

you can seek help from the experts. Choose from the options below:

1. Visit www.bolens.ca for many useful suggestions, click on Customer Support button.

2. Call a Customer Support Representative at 1-800-668-1238.

3. The engine manufacturer is responsible for all engine-related issues in terms of performance, power-rating, specifications,

warranty, and service. Depending on the engine manufacturer, more information is included in this publication or packed

separately with this product.

Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.

You will be asked to enter the serial number in order to process your call.

-4$02/$5#43,)-)4%$

+)4#(%.%2/..'*



8888888888

88888888888

-ODEL.UMBER

.UM£RODEMODÞLE

3ERIAL.UMBER

.UM£RODES£RIE

WWWMTDCANADACOM

Slope

Gauge

WARNING

Do not mow on inclines

with a slope in excess

of 15 degrees (a rise

of approximately

2-1/2 feet every 10

feet). A riding mower

could overturn and

cause serious injury.

If operating a walk-

behind mower on such

a slope, it is extremely

difficult to maintain your

footing and you could

slip, resulting in serious

injury.

Operate RIDING

mowers up and down

slopes, never across

the face of slopes.

Operate

WALK-BEHIND

mowers across the

face of slopes, never

up and down slopes.

Sight and hold this level with a vertical tree...

or a corner of a building...

or a fence post

Fold along dotted line (represents a 15° slope)

15°

Use this page as a guide to determine slopes where you may not operate safely. Do not operate

your lawn mower on such slopes.

Safe

Operation

Practices

General Operation

1. Read this operator’s manual carefully in its entirety

before attempting to assemble this machine. Read,

understand, and follow all instructions on the ma-

chine and in the manual(s) before operation. Keep

this manual in a safe place for future and regular

reference and for ordering replacement parts.

2. Be completely familiar with the controls and the

proper use of this machine before operating it.

3. This machine is a precision piece of power equip-

ment, not a plaything. Therefore, exercise extreme

caution at all times. Your unit has been designed to

perform one job: to mow grass. Do not use it for any

other purpose.

4. Never allow children under 14 years old to operate

this machine. Children 14 years old and over should

read and understand the instructions in this manual

and should be trained and supervised by a adult.

5. Only responsible individuals who are familiar with

these rules of safe operation should be allowed to

use this machine.

6. Thoroughly inspect the area where the equipment is

to be used. Remove all stones, sticks, wire, bones,

toys and other foreign objects which could be tripped

over or picked up and thrown by the blade. Thrown

objects can cause serious personal injury.

7. Plan your mowing pattern to avoid discharge of

material toward roads, sidewalks, bystanders and the

like. Also, avoid discharging material against a wall

or obstruction which may cause discharged material

to ricochet back toward the operator.

8. To help avoid blade contact or a thrown object injury,

stay in the operator zone behind the handles and

keep children, bystanders, helpers and pets at least

75 feet from the mower while it is in operation. Stop

machine if anyone enters the area.

9. Always wear safety glasses or safety goggles during

operation and while performing an adjustment or repair

to protect your eyes. Thrown objects which ricochet can

cause serious injury to the eyes.

10. Wear sturdy, rough-soled work shoes and close-

fitting slacks and shirts. Shirts and pants that

cover the arms and legs and steel-toed shoes are

recommended. Never operate this machine in bare

feet, sandals, slippery or light weight (e.g. canvas)

shoes.

11. Do not put hands or feet near rotating parts or under

the cutting deck. Contact with the blade can amputate

hands and feet.

12. A missing or damaged discharge cover can cause

blade contact or thrown object injuries.

13. Many injuries occur as a result of the mower being

pulled over the foot during a fall caused by slipping or

tripping. Do not hold on to the mower if you are falling;

release the handle immediately.

14. Never pull the mower back toward you while you are

walking. If you must back the mower away from a wall

or obstruction first look down and behind to avoid

tripping and then follow these steps:

a. Step back from the mower to fully extend your

arms.

b. Be sure you are well balanced with sure footing.

c. Pull the mower back slowly, no more than half way

toward you.

d. Repeat these steps as needed.

15. Do not operate the mower while under the influence of

alcohol or drugs.

16. Do not engage the self-propelled mechanism on units

so equipped while starting engine.

17. The blade control handle is a safety device. Never

attempt to bypass its operation. Doing so makes the

safety device inoperative and may result in personal

injury through contact with the rotating blade. The

blade control handle must operate easily in both

directions and automatically return to the disengaged

position when released.

18. Never operate the mower in wet grass. Always be

sure of your footing. A slip and fall can cause serious

personal injury. If you feel you are losing your footing,

release the blade control handle immediately and the

blade will stop rotating within three seconds.

19. Mow only in daylight or in good artificial light. Walk,

never run.

20. Stop the blade when crossing gravel drives, walks or

roads.

21. If the equipment should start to vibrate abnormally,

stop the engine and check immediately for the cause.

Vibration is generally a warning of trouble.

WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain

or emit chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm.

WARNING

This symbol points

out important safety

instructions which, if

not followed, could

endanger the personal

safety and/or property

of yourself and others.

Read and follow all

instructions in this

manual before at-

tempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

HEED ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with

any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This

machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety

instructions could result in serious injury or death.

22. Shut the engine off and wait until the blade comes to

a complete stop before removing the grass catcher or

unclogging the chute. The cutting blade continues to

rotate for a few seconds after the engine is shut off.

Never place any part of the body in the blade area until

you are sure the blade has stopped rotating.

23. Never operate mower without proper trail shield,

discharge cover, grass catcher, blade control handle or

other safety protective devices in place and working.

Never operate mower with damaged safety devices.

Failure to do so, can result in personal injury.

24. Muffler and engine become hot and can cause a burn.

Do not touch.

25. Never attempt to make a wheel or cutting height

adjustment while the engine is running.

26. Only use parts and accessories made for this machine

by the manufacturer. Failure to do so can result in

personal injury.

27. When starting engine, pull cord slowly until resistance

is felt, then pull rapidly. Rapid retraction of starter cord

(kickback) will pull hand and arm toward engine faster

than you can let go. Broken bones, fractures, bruises

or sprains could result.

28. If situations occur which are not covered in this

manual, use care and good judgment. Call customer

assistance for the name of your nearest servicing

dealer.

Slope Operation

Slopes are a major factor related to slip and fall accidents

which can result in severe injury. Operation on slopes

requires extra caution. If you feel uneasy on a slope, do

not mow it. For your safety, use the slope gauge included

as part of this manual to measure slopes before operating

this unit on a sloped or hilly area. If the slope is greater

than 15 degrees, do not mow it.

Do:

1. Mow across the face of slopes; never up and down.

Exercise extreme caution when changing direction on

slopes.

2. Watch for holes, ruts, rocks, hidden objects, or bumps

which can cause you to slip or trip. Tall grass can hide

obstacles.

3. Always be sure of your footing. A slip and fall can

cause serious personal injury. If you feel you are

losing your balance, release the blade control handle

immediately, and the blade will stop rotating within 3

seconds.

Do Not:

1. Do not mow near drop-offs, ditches or embankments,

you could lose your footing or balance.

2. Do not mow slopes greater than 15 degrees as shown on the

slope gauge.

3. Do not mow on wet grass. Unstable footing could

cause slipping.

Children

Tragic accidents can occur if the operator is not alert to

the presence of children. Children are often attracted

to the mower and the mowing activity. They do not

understand the dangers. Never assume that children

will remain where you last saw them.

1. Keep children out of the mowing area and under the

watchful care of a responsible adult other than the

operator.

2. Be alert and turn mower off if a child enters the area.

3. Before and while moving backwards, look behind

and down for small children.

4. Use extreme care when approaching blind corners,

doorways, shrubs, trees, or other objects that may

obscure your vision of a child who may run into the

mower.

5. Keep children away from hot or running engines.

They can suffer burns from a hot muffler.

6. Never allow children under 14 years old to operate a

power mower. Children 14 years old and over should

read and understand the operation instructions and

safety rules in this manual and shou

ld be trained and

supervised by a parent.

Service

Safe Handling Of Gasoline:

1. To avoid personal injury or property damage use

extreme care in handling gasoline. Gasoline is

extremely flammable and the vapors are explosive.

Serious personal injury can occur when gasoline is

spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

2. Use only an approved gasoline container.

3. Never fill containers inside a vehicle or on a truck or

trailer bed with a plastic liner. Always place contain-

ers on the ground away from your vehicle before

filling.

4. Remove gas-powered equipment from the truck

or trailer and refuel it on the ground. If this is not

possible, then refuel such equipment on a trailer with

a portable container, rather than from a gasoline

dispenser nozzle.

5. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

6 Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

7. Never fuel machine indoors because flammable

vapors will accumulate in the area.

8. Never remove gas cap or add fuel while the engine

is hot or running. Allow engine to cool at least two

minutes before refueling.

Safe

Operation

Practices

WARNING

This machine is equipped

with an internal combus-

tion engine and should

not be used on or near

any unimproved forest-

covered, brushcovered or

grass-covered land unless

the engine’s exhaust

system is equipped with a

spark arrester meeting ap-

plicable local or provincial

laws (if any).

If a spark arrester is used,

it should be maintained in

effective working order by

the operator.

A spark arrester for the muf-

fler is available through your

nearest engine authorized

service dealer.

Notice regarding Emis-

sions

Engines which are certified

to comply with California

and federal EPA emission

regulations for SORE (Small

Off Road Equipment) are

certified to operate on regu-

lar unleaded gasoline, and

may include the following

emission control systems:

Engine Modification (EM)

and Three Way Catalyst

(TWC) if so equipped.

9. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to provide for fuel

expansion.

10. Replace gasoline cap and tighten securely.

11. If gasoline is spilled, wipe it off the engine and equip-

ment. Move unit to another area. Wait 5 minutes

before starting the engine.

12. Never store the machine or fuel container near an

open flame, spark or pilot light as on a water heater,

space heater, furnace, clothes dryer or other gas

appliances.

13. To reduce fire hazard, keep mower free of grass,

leaves, or other debris build-up. Clean up oil or fuel

spillage and remove any fuel soaked debris.

14. Allow a mower to cool at least 5 minutes before

storing.

General Service:

1. Never run an engine indoors or in a poorly ventilated

area. Engine exhaust contains carbon monoxide, an

odorless and deadly gas.

2. Before cleaning, repairing, or inspecting, make

certain the blade and all moving parts have stopped.

Disconnect the spark plug wire and ground against

the engine to prevent unintended starting.

3. Check the blade and engine mounting bolts at

frequent intervals for proper tightness. Also, visually

inspect blade for damage (e.g., bent, cracked, worn)

Replace blade with the original equipment manufac-

ture’s (O.E.M.) blade only, listed in this manual. “Use

of parts which do not meet the original equipment

specifications may lead to improper performance

and compromise safety!”

4. Mower blades are sharp and can cut. Wrap the blade

or wear gloves, and use extra caution when servicing

them.

5. Keep all nuts, bolts, and screws tight to be sure the

equipment is in safe working condition.

6. Never tamper with safety devices. Check their proper

operation regularly.

7. After striking a foreign object, stop the engine,

disconnect the spark plug wire and ground against

the engine. Thoroughly inspect the mower for any

damage. Repair the damage before starting and

operating the mower.

8. Never attempt to make a wheel or cutting height

adjustment while the engine is running.

9. Grass catcher components, discharge cover, and trail

shield are subject to wear and damage which could

expose moving parts or allow objects to be thrown. For

safety protection, frequently check components and

replace immediately with original equipment manufac-

turer’s (O.E.M.) parts only, listed in this manual. “Use

of parts which do not meet the original equipment

specifications may lead to improper performance and

compromise safety!”

10. Do not change the engine governor setting or

overspeed the engine. The governor controls the

maximum safe operating speed of the engine.

11. Check fuel line, tank, cap, and fittings frequently for

cracks or leaks. Replace if necessary.

12. Do not crank engine with spark plug removed.

13. Maintain or replace safety labels, as necessary.

14. Observe proper disposal laws and regulations.

Improper disposal of fluids and materials can harm the

environment.

15. According to the Consumer Products Safety Commis-

sion (CPSC) and the U.S. Environmental Protection

Agency (EPA), this product has an

Average Useful Life

of seven (7) years, or 60 hours of operation. At the

end of the Average Useful Life, buy a new machine or

have the machine inspected annually by an authorized

service dealer to ensure that all mechanical and safety

systems are working properly and not worn exces-

sively. Failure to do so can result in accidents, injuries

or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in

any way. Tampering with the governor setting can lead

to a runaway engine and cause it to operate at unsafe

speeds. Never tamper with factory setting of engine

governor.

Safe

Operation

Practices

WARNING

This symbol points

out important safety

instructions which,

if not followed,

could endanger the

personal safety and/

or property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may result

in personal injury. When

you see this symbol.

HEED ITS WARNING!

Your Responsibility

Restrict the use

of this power machine

to persons who read,

understand

and follow the warnings

and instructions

in this manual

and on the machine.

WARNING: Your Responsibility—Restrict the use of this power machine to persons who

read, understand and follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before

attempting to assemble and operate

DANGER — ROTATING BLADES

To reduce the risk of injury, keep hands and feet away. Do not operate

unless discharge cover or grass catcher is in its proper place. If damaged,

DANGER — BYSTANDERS

Do not mow when children or others are around.

DANGER — HAND/ FOOT CUT

Keep hands and feet away from rotating parts.

DANGER — THROWN DEBRIS

Remove objects that can be thrown by the blade in any direction. Wear

safety glasses.

DANGER — SLOPES

Use extra caution on slopes. Do not mow slopes greater than 15°.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust

contains carbon monoxide, an odorless and deadly gas.

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during opera-

tion. Allow engine and muffler to cool before touching.

Safety

Symbols

WARNING

This symbol points

out important safety

instructions which,

if not followed, could

endanger the per-

sonal safety and/or

property of yourself

and others. Read and

follow all instructions

in this manual before

attempting to operate

this machine. Failure

to comply with these

instructions may

result in personal

injury. When you see

this symbol, HEED

ITS WARNING!

Figure 3-2

Figure 3-3

Figure 3-4

1. Attaching Rear Wheels (If Not Already Attached)

a. Place rear of the mower deck on raised blocks.

b. Remove the hex flanged nut on the rear axle

from each side and place the rear wheel on the

axle. (On select models, these may be included

separately in a plastic bag).

c. On models with 2” wide rear wheels, make sure

the spring washer is on the inside of the wheel

between the wheel and the lawnmower, cupped

side towards the bracket. See Figure 3-1.

d. Reinsert the flanged nut into the axle as shown,

and tighten securely. Repeat on other side.

2. Remove loose parts and any packing material which

may be between upper and lower handles.

a. Pull up and back on the upper handle to raise the

handle from position A into the operating position.

See Figure 3-2.

b. Tighten knobs securing upper handle to lower

handle. Make sure that each carriage bolt is

seated properly in the handle.

3. Locate hairpin clip in one hole on the weld pin on each

side of lower handle.

a. Remove hairpin clip from this hole. Using a pair of

pliers, insert hairpin clip into the other hole on the

weld pin. Repeat on other side. See Figure 3-3.

b. Place one carriage bolt (found in the hardware

pack included with your unit) in the upper hole of

the right handle mounting bracket from the inside

outward. See Figure 3-3. Secure with one wing

nut. Repeat process on the left side.

4. Rope guide Setup as follows, see Figure 3-4:

a. Hold the blade control against the upper handle.

Position A.

b. Slowly pull starter rope out of engine. Position B.

c. Slip starter rope into the rope guide. Position C.

d. Tighten rope guide wing nut (star knobs).Position D.

Figure 3-1

Disconnect and

ground the spark

plug wire as instruct-

ed in the separate

engine manual.

IMPORTANT

This unit is shipped

WITHOUT GASOLINE

or OIL. After assem-

bly, service engine

with gasoline and

oil as instructed in

the separate engine

manual packed with

your unit.

Make sure to route

cable outside the

lower handle. Do not

crimp cable while

lifting the handle up.

Setup and

Adjustments

WARNING

On models with 2”

wide rear wheels only.

Handle Bracket

NOTE: This owner’s manual covers various models

of lawnmowers. The units illustrated may vary

slightly from your unit. Follow only those instruc-

tions which pertain to your model lawnmower.

5. Insert post on cable tie into hole provided on the lower

handle. Pull cable tie tight and trim excess. See Figure

3-5.

Figure 3-8

Figure 3-6

Figure 3-7

Figure 3-5

6. Each wheel has a height adjustment lever to change

the cutting height of the mower. To change the height

of cut, squeeze adjuster lever toward the wheel,

moving up or down to selected height. See Figure 3-6.

7. To assemble the grasscatcher:

a. Place bag over frame (black plastic side is the

bottom of bag.) Insert the hooks on the frame

through the holes in the side plastic channels of

the bag. See Figure 3-7.

b. Secure bag to frame by working the plastic chan-

nels on bag over frame as shown in Figure 3-7. All

of the plastic channels except center top of bag

attach from the outside of bag. Center top of bag

attaches from the inside of bag.

8. Attaching Grass Catcher to Mower

a. Lift the rear discharge door on the mower, and

place the grass catcher on the pivot rod. Let go

of discharge door so that it rests on the grass

catcher. See Figure 3-8.

WARNING: Never operate mower

unless the hooks on the grass

catcher are firmly seated on the

pivot rod, and the rear discharge

door rests firmly against top of

the grass catcher.

9. To remove grass catcher and utilize the mulching

feature:

a. Lift rear discharge door on the mower as shown in

Figure 3-8. Lift grass catcher up and out, off of the

pivot rod. Release rear discharge door to allow it to

close rear opening of mower.

NOTE: Make certain

bag is turned right side

out before assembling

(warning label will be on

the outside).

NOTE: Make certain

cables are routed to the

outside of the handle so

they are not in the way

when attaching the grass

catcher.

Never operate mower

unless the hooks on

the grass catcher are

firmly seated on the

pivot rod, and the

rear discharge door

rests firmly against

top of the grass

catcher.

All mowers are

equipped with a rear

protective guard. The

guard helps eliminate

projectiles thrown

by the blade from

injuring the operator.

DO NOT REMOVE

THIS GUARD.

WARNING

Setup and

Adjustments

Operating

Your Lawn

Mower

Blade Control Handle

The blade control handle is located on the upper handle

of the mower. See Figure 4-1. The blade control handle

must be depressed in order to operate the unit. Release

the blade control handle to stop the engine and blade.

Recoil Starter

The recoil starter is attached to the right upper handle.

Stand behind the unit and pull the recoil starter rope to

start the unit.

Mulching Plug (optional)

The mulching plug is used to close the side discharge

chute opening when mulching or bagging grass. Do

not remove the hinged mulching plug at any time, even

when you are not mulching.

Cutting Height Adjustment Levers

(If so equipped)

One adjustment lever is located on each wheel and is

used to adjust the cutting height. All four levers have to

be at the same relative position to ensure uniform cut.

Before Starting

1. Service the engine with gasoline and oil as instructed

in the separate engine manual.

2. Attach spark plug wire to spark plug. If unit is

equipped with a rubber boot over the end of the spark

plug wire, make certain the metal loop on the end of

the spark plug wire (inside the rubber boot) is fastened

securely over the metal tip on the spark plug.

To Start Engine

1. If your unit is equipped with a primer, prime engine as

instructed in the separate engine manual packed with

your unit.

2. Standing behind the unit, depress the blade control

handle and hold it against the upper handle as shown

in Figure 4-2.

3. Grasp the starter handle as shown and pull slowly

until resistance is felt, then pull rapidly to start engine

and avoid kickback. Return it slowly to the rope guide.

WARNING

Figure 4-1

Know Your Lawn Mower

Blade Control

Recoil

Starter

Grass

Catcher

Spark Plug

Mulch Plug

(optional)

Cutting Height

Adjustment Lever

(for each wheel)

Side Deflector

(optional)

Read, understand,

and follow all instruc-

tions and warnings

on the machine and

in this manual before

operating.

This blade control

mechanism is a

safety device. Never

attempt to bypass its

operations.

Use extreme care

when handling

gasoline. Gasoline is

extremely flammable

and the vapors are

explosive. Never fuel

the machine indoors

or while the engine

is hot or running.

Extinguish cigarettes,

cigars, pipes and

other sources of

ignition.

NOTE: To operate your unit using the grass catcher or

optional side discharge refer to page 7.

The side discharge is an optional feature.

If converting to side discharge, make sure grass

catcher is off unit and rear discharge door is closed.

a. On the side of the mower deck, lift the hinged

mulching plug. See Figure 4-3.

b. Slide the two hooks on the side discharge deflec-

tor under the hinge pin on the hinged mulching

plug assembly. Lower the hinged mulching plug.

NOTE: Do not remove the hinged mulching plug at any

time, even when you are not mulching.

To Stop Engine

1. Release the blade control handle to stop the engine

and blade.

WARNING: The blade continues

to rotate for a few seconds after

the engine is shut off.

2. Disconnect and ground the spark plug wire as

instructed in the separate engine manual to prevent

accidental starting while equipment is unattended.

Using Your Lawn Mower

WARNING: Never operate your

mower without either the rear

door or the entire grass catcher

assembly firmly secured.

Be sure the lawn is clear of stones, sticks, wire, or other

objects which could damage the lawn mower or the

engine. Such objects could be accidently thrown by the

mower in any direction and cause serious personal injury

to the operator and others.

WARNING: If you strike a foreign

object, stop the engine. Remove

wire from the spark plug, thor-

oughly inspect the mower for any

damage, and repair the damage

before restarting and operating

the mower. Extensive vibration

of the mower during operation is

an indication of damage. The unit

should be promptly inspected

and repaired.

Operating Tips

1. For best results and effective mulching, do not cut wet

grass.

2. New grass, thick grass, or wet grass may require a

narrower cut.

3. For a healthier lawn, never cut off more than one-third

of the total length of the grass.

4. Your lawn should be cut in the fall as long as there

is growth.

5. Adjust ground speed according to condition of lawn.

6. If the grass has been allowed to grow in excess of 4

inches, mulching is not recommended. Mow using

the grass catcher to reduce the grass height to 3-1/4

inches or less before mulching.

WARNING: Wait for the blade to

stop completely before doing any

work on the mower or to remove

the grass catcher.

Operating

Your Lawn

Mower

WARNING

The operation of any

lawn mower can result

in foreign objects

being thrown into

the eyes, which can

damage your eyes

severely. Always wear

safety glasses while

operating the mower,

or while performing

any adjustments or

repairs on it.

Be sure no one other

than the operator is

standing near the lawn

mower while starting

engine or operating

mower. Never run

engine indoors or

in enclosed, poorly

ventilated areas. En-

gine exhaust contains

carbon monoxide, an

odorless and deadly

gas. Keep hands, feet,

hair and loose clothing

away from any moving

parts on engine and

lawn mower.

Figure 4-2

Figure 4-3 - Optional Feature (If equipped)

/&&







Maintenance

WARNING

Always stop engine,

disconnect spark

plug, and ground

against engine before

cleaning, lubricating

or doing any kind of

maintenance on your

machine.

Figure 5-1

General Recommendations

1. Always observe safety rules when performing

any maintenance.

2. The warranty on this lawn mower does not cover

items that have been subjected to operator abuse

or negligence. To receive full value from warranty,

operator must maintain the lawn mower as

instructed here.

3. Changing of engine-governed speed will void

engine warranty.

4. All adjustments should be checked at least once

each season.

5. Periodically check all fasteners and make sure these

are tight.

Lubrication

1. Lubricate the pivot points on the blade control handle

at least once a season with light oil. The blade

control must operate freely in both directions. See

Figure 5-1.

2. If your mower is equipped with ball bearing wheels,

lubricate at least once a season with a light oil, all

other types require no lubrication. However, if the

wheels are removed for any reason, lubricate the

surface of the axle bolt and the inner surface of the

wheel with light automotive oil.

3. Lubricate the torsion spring and pivot point on the

rear door periodically with light oil to prevent rust.

See Figure 5-1.

4. Follow the accompanying engine manual for lubrica-

tion schedule and instruction.

Lubricate these

points before

ressembly

Engine

1. Refer to the separate engine manual for engine

maintenance instructions.

2. Maintain engine oil as instructed in the separate

engine manual packed with your unit. Read and follow

instructions carefully.

3. Under normal conditions service air cleaner as

instructed in the separate engine manual packed with

your unit. Clean every few hours under extremely

dusty conditions. Poor engine performance and

flooding usually indicates that the air cleaner should be

serviced.

4. The spark plug should be cleaned and the gap reset

once a season. Spark plug replacement is recom-

mended at the start of each mowing season; check

engine manual for correct plug type and gap specifica-

tions.

NOTE: This spark ignition system meets all require-

ments of the Canadian Interference-Causing Equipment

Regulations.

5. Clean the engine regularly with a cloth or brush.

Keep the cooling system (blower housing area) clean

to permit proper air circulation which is essential to

engine performance and life. Be certain to remove all

grass, dirt and combustible debris from muffler area.

Deck

The underside of the mower deck should be cleaned after

each use to prevent a buildup of grass clippings, leaves,

dirt or other matter. If this debris is allowed to accumulate,

it will invite rust and corrosion, and may prevent proper

mulching.

The deck may be cleaned by tilting the mower and scrap-

ing clean with a suitable tool (make certain the spark plug

wire is disconnected).

Blade Care

WARNING: When removing the

cutting blade for sharpening or

replacement, protect your hands

with a pair of heavy gloves or use

a heavy rag to hold the blade.

Periodically inspect the blade adapter for cracks, especial-

ly if you strike a foreign object. Replace when necessary.

Follow the steps below for blade service:

1. Disconnect spark plug wire from spark plug.

2. Tip mower as specified in separate engine manual. If

it does not specify turn mower on its side making sure

that the air filter and the carburetor are up.

3. Remove the bolt and the blade bell support which

hold the blade and the blade adapter to the engine

crankshaft. See Figure 5-2.

We do not recommend

the use of pressure

washers or garden

hose to clean your

unit. These may cause

damage to electrical

components, spindles,

pulleys, bearings, or

the engine. The use

of water will result in

shortened life and

reduce serviceability.

WARNING

When removing

the cutting blade

for sharpening or

replacement, protect

your hands with a

pair of heavy gloves

or use a heavy rag to

hold the blade.

An unbalanced blade

will cause excessive

vibration when rotat-

ing at high speeds. It

may cause damage

to mower, and could

break causing per-

sonal injury.

Figure 5-2

Maintenance

4. Remove blade and adapter from the crankshaft.

5. The blade may be resharpened by removing it and

either grinding or filing the cutting edge keeping as

close to the original bevel as possible. Do not attempt

to sharpen the blade while it is still on the mower.

6. It is extremely important that each cutting edge

receives an equal amount of grinding to prevent an

unbalanced blade.

NOTE: Improper blade balance will result in excessive

vibration causing eventual damage to the engine and

mower. Be sure to carefully balance blade after sharpen-

ing. Possible damage resulting from blade unbalance

condition is not the responsibility of the manufacturer.

NOTE: Always remove blade from the adapter for testing

balance.

7. The blade can be tested for balance by balancing it

on a round shaft screwdriver. Remove metal from the

heavy side until it balances evenly.

8. Before reassembling the blade and the blade adapter

to the unit, lubricate the engine crankshaft and the

inner surface of the blade adapter with light oil.

9. Install the blade adapter on the crankshaft with the

“star” away from the engine. See Figure 5-3. Place

the blade with the side marked “bottom” (or with part

number) facing away from the adapter. Align the

blade bell support over the blade with the tabs in the

holes of the blade and insert the hex bolt.

10. Tighten the hex bolt to the torque listed below:

Blade Mounting Torque

Center Bolt 450 in. lb. min., 600 in.lb. max.

To insure safe operation of your unit, ALL nuts and bolts

must be checked periodically for correct tightness.

Cutting grass in sandy

soil condition causes

abrasive wear to the

blade.

Rear Flap Replacement

The rear flap is attached to the back of the mower deck,

and is designed to minimize the possibility that objects

will be thrown from the rear of the mower toward the

operator. If the rear flap becomes damaged, replace as

follows.

1. To remove the old rear flap, lift rear door, and press

flap in on either side to remove from hole. See Figure

5-3.

2. Remove flap from opposite hole and replace with new

flap following these steps in reverse order.

Off-Season Storage

The following steps should be taken to prepare your lawn

mower for storage.

1. Clean and lubricate mower thoroughly as described in

the lubrication instructions.

2. We do not recommend the use of a pressure washer

or garden hose to clean your unit.

3. Refer to engine manual for correct engine

storage instructions.

4. Coat mower’s cutting blade with chassis grease to

prevent rusting.

5. Store mower in a dry, clean area. Do not store next to

corrosive materials, such as fertilizer.

NOTE: When storing any type of power equipment in

a poorly ventilated or metal storage shed, care should

be taken to rust-proof the equipment. Using a light oil or

silicone, coat the equipment, especially cables and all

moving parts of your lawn mower before storage.

Figure 5-3

For repairs beyond

the minor adjust-

ments listed here,

contact an autho-

rized service dealer.

Trouble

Shooting

CauseProblem

Remedy

Engine fails to start

1. Blade control handle disengaged.

2. Spark plug wire disconnected.

3. Fuel tank empty or stale fuel.

4. Engine not primed.

5. Faulty spark plug.

6. Blocked fuel line.

7. Engine flooding.

1. Engage blade control handle.

2. Connect wire to spark plug.

3. Fill tank with clean, fresh gasoline.

4. Refer to engine manual.

5. Clean, adjust gap, or replace.

6. Clean fuel line.

7. Wait a few minutes to restart, but do not

prime.

Engine runs erratic 1. Connect and tighten spark

plug wire.

2. Clean fuel line; fill tank with clean, fresh

gasoline.

3. Clear vent.

4. Drain fuel tank and carburetor. Refill with

fresh fuel.

5. Refer to engine manual.

6. Refer to engine manual.

1. Spark plug wire loose.

2. Blocked fuel line or stale fuel.

3. Gas cap vent plugged.

4. Water or dirt in fuel system.

5. Dirty air cleaner.

6. Carburetor out of adjustment.

Engine overheats

1. Fill crankcase with proper oil.

2. Refer to the engine manual packed with

your unit.

3. Remove blower housing and clean.

4. Refer to engine manual.

1. Engine oil level low.

2. Dirty air filter.

3. Air flow restricted.

4. Carburetor not adjusted properly.

Occasional skip

(hesitates) at high speed

1. Adjust gap to .030”. Refer to engine

manual.

2. Refer to engine manual.

1. Spark plug gap too close.

2. Carburetor idle mixture adjustment

improperly set.

Idles poorly

1. Reset gap to .030” or replace spark plug.

Refer to engine manual.

2. Refer to engine manual.

3. Refer to engine manual.

1. Spark plug fouled, faulty or gap too

wide.

2. Carburetor improperly adjusted.

3. Dirty air cleaner.

1. Cutting Blade loose or unbalanced.

2. Bent cutting blade.

1. Tighten blade and adapter. Balance blade

2. Replace blade.

Excessive vibration

1. Wheels not positioned correctly.

2. Dull blade.

Uneven cut

1. Place all four wheels in same height

position.

2. Sharpen or replace blade.

1. Wet grass.

2. Excessive high grass.

3. Dull blade.

1. Do not mow when grass is wet;

wait until later to cut.

2. Mow once at a high cutting height, then

mow again at desired height or make a

narrower cutting path.

3. Sharpen or replace blade.

Mower will not mulch

grass

Warranty

Failure to comply

with suggested

maintenance

and lubrication

specifications will

void warranty.

4 YEAR LIMITED WARRANTY

For FOUR YEARS from the date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair

or replace, for the original purchaser, free of charge, any part or parts found to be defective in material or workmanship.

This warranty does not cover:

1. Any part which has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper mainte-

nance or alteration; or

2. The unit if it has not been operated and/or maintained in accordance with the owner’s instructions furnished with the

unit; or

3. The engine or motor or component parts thereof which carry separate warranties from their manufacturers. Please

refer to the applicable manufacturer’s warranty on these items; and read engine warranty statement below, or

4. Batteries and normal wear parts except as noted below. Log splitter pumps, valves and cylinders or component parts

thereof are covered by a one year warranty; or

5. Routine maintenance items such as lubricants, filters, blade sharpening and tune-ups, or adjustments such as brake,

clutch or deck; or

6. Normal deterioration of the exterior finish due to use or exposure.

Full Ninety Day Warranty on Battery (if equipped): For ninety (90) days from the date of retail purchase, if any

battery included with this unit proves defective in material or workmanship and our testing determines the battery will

not hold a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original purchaser.

Additional Limited Thirty Day Warranty on Battery (if equipped): After ninety (90) days but within one hundred

twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective battery, for the

original purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at the date of return.

Full Ninety Days Warranty on Normal Wear Parts: Normal wear parts are defined as belts, blade adaptors, blades,

grass bags, seats, tires, rider deck wheels and clutch parts (friction wheels). These parts are warranted to the original

purchaser to be free from defects in material and workmanship for a period of ninety (90) days from the date of retail

purchase.

How to Obtain Service: Warranty service is available, with proof of purchase, through your local authorized service

dealer or distributor. If you do not know the dealer or distributor in your area, please call, toll free 1-800-668-1238. The

return of a complete unit will not be accepted by the factory unless prior written permission has been extended by MTD

PRODUCTS LIMITED.

Transportation Charges: Transportation charges for the movement of any power equipment unit or attachment are

the responsibility of the purchaser. Transportation charges for any part submitted for replacement under this warranty

must be paid by the purchaser unless such return is requested in writing by MTD PRODUCTS LIMITED.

Other Warranties: All other warranties, express or implied, including any implied warranty of merchantability is limited

in its duration to that set forth in this express limited warranty. The provisions as set forth in this warranty provide the

sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale of its products.

MTD PRODUCTS LIMITED will not be liable for incidental or consequential loss or damage.

4 YEAR LIMITED WARRANTY ENGINES

This limited warranty doubles the time periods of the engine manufacturer’s limited warranty which is enclosed in the

owner’s information package.

12.08.06

23B

23A

17A

17B

REF PART

NO. NO.

N° DE N° DE

RÉF PIÈCE DE SCRIP TION DE SCRIP TION

1 747-1161A Blade Con trol Han dle - Black Poignée de commande de la lame - noir

2 749-1092A Up per Han dle - Black Guidon supérieur - noir

3 747-04080A Catcher Lower Frame Sac à herbe - bâti inférieur

4 749-0928B Lower Han dle Guidon inférieur

5 720-0279 Knob 1/4-20 Bou ton 1/4-20

6 710-1205 Rope Guide Bolt Boulon de guidage de cor don

7 710-1174 Curved Car riage Bolt 5/16-18 x 2.00 Boulon ordi naire courbé 5/16-18 x 2,00

8 664-04007A Ge neric Grasscatcher Bag - Black Sac à herbe - noir

664-04027 Grasscatcher Bag YM Sac à herbe YM

664-04011 Grasscatcher Bag Troy w/la bel Sac à herbe Troy avec étiquette

664-04068 Grasscatcher Bag MTD Gold Sac à herbe MTD Gold

664-04034A Grasscatcher Bag WOP Sac à herbe WOP

9 736-0182 Spring Wash. .5 x 1.0 (w/2" side rear whls) Rondelle 0,5 x 1,0 (avec 2 po roues arrière)

10 710-0606 Hex Cap Screw1/4-20 x 1.5" Lg. Vis à tête hex. 1/4-20 x 1,5 po de lg.

11 726-0240 Ca ble Tie Attache câble

12 710-0703 Car riage Bolt 1/4-20 x .75 Gr. 1 Boulon ordi naire 1/4-20 x 0,75 Qual. 1

13 731-06885 RB Chute Door Porte de goulotte

16 732-04090A RH Tor sion Spring Ressort de tor sion CD

17A 734-04082 Wheel Ass'y Comp.12 x 1.8 Bar Grey Ens. de roue complet 12 x 1,8 Bar Gris

17A 734-04089 Wheel Ass'y Comp.12 x 1.8 Bar Yellow Ens. de roue complet 12 x 1,8 Bar Jaune

17B 734-04093 Wheel Ass'y Comp.12 x 2.125 Idle Zag Grey Ens. de roue complet 12 x 2.125 Idle Zag Gris

18 734-04150C RR Baf fle Déflecteur de déchiquetage arrière droit

19 720-04072 Knob - Star 5/16-18 Bou ton - étoile 5/16-18

20 787-01279 21" Deck Ass’y (w/ side dis charge) Pla teau de coupe de 21 po (avec éjection latérale)

787-01276 21" Deck Ass’y (w/o side dis charge) Pla teau de coupe de 21 po (sans éjection latérale)

22 782-5002B Front Baf fle 21" Déflecteur de déchiquetage avant 21 po

23A 748-04082 Blade Adapter 25 mm x 2.15 (w/star) Adaptateur de la lame 25 mm x 2,15

23B 748-0377C Blade Adapter #6 x 2.15 (w/star) Adaptateur de la lame no. 6 x 2,15

24 742-0641 21" Blade (w/star) Lame 21 po (avec étoile)

742-0741 21" Mulch ing Blade (w/star) Lame de déchiquetage 21 po (avec étoile)

25 710-1257 Hex Bolt 3/8-24 x 2.5" Lg. Gr. 8 Vis à tête hex. 3/8-24 x 2,50 po de lg Qual. 8

26 687-0337 Pivot Bar RH Barre de pivot CD

687-0336 Pivot Bar LH Barre de pivot CG

27 736-0524B Blade Bell Sup port Sup port de la lame

28 787-01290A Height Ad juster Plate Plaque de réglage de roue

29 720-0426 Knob Bou ton

30 732-0404 Spring Le ver Ass’y Lev ier de ressort

31 738-04266 Shoul der Screw .50 Dia. x .385 Vis à épaulement 0,50 Dia. x 0,385

32 734-02004A Wheel Ass'y 8 x 2.125 Idle Zab BB En sem ble de roue 8 x 2,125 Idle Zag BB

734-02005A Wheel Ass'y 8 x 2.125 Idle Zab En sem ble de roue 8 x 2,125 Idle Zag

734-1987 Wheel Ass'y 8 x 1.8 Spoke Bar Grey En sem ble de roue 8 x 1,8 Gris

734-04086 Wheel Ass'y 7 x 1.8 Bar (Yel low) En sem ble de roue 7 x 1,8 Bar (jaune)

33 710-01241 Hex. L-Scr. 1/4-15 x 1.0 Vis hex. 1/4-15 x 1,0

34 746-1130 Control Ca ble 40.0" Lg. (w/Honda & B&S) Câble 40,0 po de lg. (avec Honda et B&S)

746-0946 Con trol Ca ble 48.25" Lg. (w/MTD) Câble 48,25 po de lg. (avec MTD)

36 731-05642A Rear Flap Abattant de pro tec tion arrière

37 712-04064 Flange Locknut 1/4-20 Écrou de blocage 1/4-20

38 712-0397 Wingnut 1/4-20 Écrou à oreilles

39 747-04588 Pivot Rod Tige de pivotement

40 732-0866 Spring Le ver SP (w/o knob) Ressort de lev ier (sans bou ton)

41 687-02039A Pivot Bar RH SP Barre de pivot - Droit

687-02040A Pivot Bar LH SP (not shown) Barre de pivot - Gauche (non illustrée)

42 710-1652 Hex HD. TT Tap Scr. 1/4-20 x 5/8 Vis TT à rondelle-frein hex. 1/4 x 5/8

43 712-04065 Flange Locknut 3/8-16 Écrou de blocage 3/8-16

44 714-0104 Int. Cot ter Pin 5/16 DIA Goupille fendue 5/16 DIA.

45 710-0654A Hex Wash HD Tap Scr 3/8-16 x .88 Vis autotaraudée 3/8-16 x 0,88

46 687-02075B Height Adj. Ass’y LH (w/8" Front Wheels) En sem ble de réglage de roue CG (avec 8 po pneu)

687-02074B Height Adj. Ass’y RH (w/8" Front Wheels) En sem ble de réglage de roue CD (avec 8 po pneu)

47 731-04859 Snap-On Bail Cover - Grey Couvercle de commande instantané - Gris

731-04204 Snap-On Bail Cover - Red Couvercle de commande instantané - rouge

731-2626 Snap-On Bail Cover - Black Couvercle de commande instantané - noir

48 687-02280A LH Rear Height Adj. Ass’y Com plete En sem ble de réglage de roue CG (complet)

687-02279A RH Rear Height Adj. Ass’y Com plete En sem ble de réglage de roue CD (complet)

49 687-02273 LH Height Adj. Brkt. En sem ble de réglage de roue CG

687-02272 RH Height Adj. Brkt. En sem ble de réglage de roue CD

50 736-0182 Spring Washer .50 ID x 1.0 OD x .022 Rondelle 0,51 DI x 1,0 DE x 0,022

51 687-02055 Com plete Hinged Mulch ing Plug Ass'y Plaque de déchiquetage de charnière

52 732-1014 Tor sion Spring Ressort de tor sion

53 747-0710 Hinge Pin Axe de charnière

54 731-04177 Chute De flec tor Déflecteur de la goulotte

55 17032A Chute Adapter Adaptateur de déflecteur

56 710-0599 Hex Wash S-Tapp Scr 1/4-20 x .50 Vis autotaraudeuse à rondelle hex 1/4-20 x 0,50.

57 736-0270 Cupped Washer .265 ID x .75 OD x .062 Rondelle creuse 0,265 DI 0,75 DE x 0,062

58 710-04577 Screw Vis

59 731-05889 Shroud (w/MTD En gine) Capot (avec moteur MTD)

60 736-0504 Wave Washer .510 x .750 x .017

Rondelle ondulée 0,510 x 0,750 x 0,017

1 710-0216 Hex Hd. Cap Screw 3/8-16 x .75 Vis à tête hex. 3/8-16 x 0,7

62 720-0312 Knob Bou ton

63 731-1426B Hub Cap - Yel low Moyeu de cha peau - jaune

731-0981C Hub Cap - Grey Moyeu de cha peau - gris

751B095050 Shroud (B&S XRT Storm Grey) Capot (B&S XRT gris)

751B796554 Screw Vis

11A-54X

1.7.09

For parts and/or

accessories refer to

customer support on

page 2.

Adressez-vous au

«Service après-vente»

à la page 2 pour ce qui

concerne les pièces

et/ou accessoires.

Parts List

Pièces

détachées

Garantie

Le non-respect des

conseils d’entretien

et de lubrification

annule la garantie.

GARANTIE LIMITÉE DE QUATRE ANS

MTD PRODUCTS LIMITED s’engage à réparer ou à remplacer gratuitement, à son choix, à l’acheteur initial, toute

pièce ou partie de pièce qui s’avère défectueuse en raison d’un vice de matière ou de fabrication, dans un délai de

QUATRE ANS à partir de la date d’achat au détail au Canada.

Cette garantie ne couvre pas:

1. Les pièces rendues inutilisables par un emploi incorrect, une utilisation commerciale, un emploi abusif, une

négligence, un entretien incorrect ou une modification;

2. La machine si elle n’a pas été utilisée et/ou entretenue conformément aux instructions qui l’accompagnaient;

3. Le moteur, le moteur électrique ou l’un de ses composants car ils sont garantis par leurs fabricants respectifs.

Veuillez consulter la garantie qui s’applique à la pièce en particulier; et lisez le paragraphe ci-dessous au sujet de

la garantie des moteurs;

4. Les batteries et les pièces présentant une usure normale énumérées plus bas. Les pompes, soupapes et cylindres

des fendeuses à bois sont garantis pendant un an;

5. Les articles d’entretien courant tels que les lubrifiants, filtres, aiguisage de lames et révisions, ou les réglages des

freins, de l’embrayage ou du plateau de coupe;

6. La détérioration normale de la finition extérieur du fait de l’utilisation de la machine et de son exposition aux

intempéries.

Garantie complète de quatre-vingt-dix jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED

s’engage à remplacer gratuitement à l’acheteur initial, pour une période de quatre-vingt-dix (90) jours à compter de

la date d’achat au détail, toute batterie fournie avec cette machine qui s’avère défectueuse en raison d’un vice de

matière ou de fabrication et après que nos tests aient confirmé qu’elle ne peut maintenir une charge.

Garantie limitée supplémentaire de trente jours sur la batterie (le cas échéant): MTD PRODUCTS LIMITED

s’engage, à l’expiration de la période de quatre-vingt-dix (90) jours et avant la fin d’une période de cent vingt (120)

jours à compter de la date d’achat, à remplacer la batterie défectueuse à l’acheteur initial, pour la moitié (1/2) du prix

de détail en vigueur de la batterie à la date du retour de celle-ci.

Garantie complète de quatre-vingt-dix (90) jours des pièces à usure normale: Les courroies, adaptateurs de

lame, lames, sacs à herbe, sièges, pneus, roues du plateau de coupe des tondeuses à siège, et pièces d’embrayage

(roues de frottement) sont considérés comme des pièces à usure normale. Elles sont garanties exemptes de vices de

matière et de fabrication à l’acheteur initial pour une période de quatre-vingt-dix (90) jours à partir de la date d’achat

au détail.

Pour faire honorer la garantie: Présentez une preuve d’achat à l’atelier de réparations ou au distributeur agréé. Si

vous ne connaissez pas l’adresse de l’atelier de réparations ou du distributeur de votre région, appelez le 1-800-668-

1238. L’usine ne peut accepter le renvoi d’une machine complète si une autorisation n’a pas été accordée par écrit par

MTD PRODUCTS LIMITED.

Frais de transport: Les frais relatifs au transport de toute machine motorisée ou de tout accessoire sont à la charge

de l’acheteur. Les frais de transport d’une pièce quelconque envoyée à des fins de remplacement en vertu de cette

garantie doivent être prise en charge par l’acheteur, sauf si le renvoi de la machine est demandé par écrit par MTD

PRODUCTS LIMITED.

Autres garanties: Toutes les autres garanties, qu’elles soient expresses ou tacites, y compris les garanties tacites de

qualité marchande, se limitent à la durée stipulée dans cette garantie limitée expresse. Les conditions stipulées dans

cette garantie constituent le recours unique et exclusif quant aux obligations de MTD PRODUCTS LIMITED découlant

de la vente de ses produits.

MTD PRODUCTS LIMITED ne peut être tenue responsable pour toute perte ou tout dommage accidentel ou indirect.

GARANTIE LIMITÉE DE 4 ANS DES MOTEURS

Cette garantie limitée double la durée de la garantie limitée du fabricant du moteur qui accompagne la documentation

à l’intention du propriétaire.

12.08.06

Pour toute

réparation autre

que les ajustements

mineurs énuméré

ici, adressez-vous à

la station technique

agréée.

Dépannage

CauseProblème Solution

Le moteur ne

démarre pas.

Le moteur tourne

irrégulièrement.

1. Branchez et serrez le fil de la bougie.

2. Nettoyez la canalisation. Faites le plein

avec une essence propre et fraîche.

3. Débouchez l’évent.

4. Videz le réservoir à carburant. Faites

le plein avec une essence fraîche.

5. Consultez la notice d’utilisation du

moteur.

6. Consultez la notice d’utilisation du

moteur.

1. Fil de la bougie desserré.

2. La canalisation de carburant est bouchée

ou l’essence est eventée.

3. L’event du capuchon du réservoir est

bouché.

4. De l’eau ou une saleté est présente dans

le système.

5. Le filtre à air est sale.

6. Le carburateur est mal régle.

1. La poignée de commande de la lame n’est

pas embrayée.

2. Fil de la bougie débranché.

3. Le réservoir est vide ou l’essence est

éventée.

4. Moteur non amorcé.

5. La bougie est défectueuse.

6. Canalisation de carburant bouchée.

7. Le moteur est noyé.

1. Embrayez la poignée de commande de

la lame.

2. Branchez le fil à la bougie.

3. Faites le plein avec une essence propre

et fraîche.

4. Consultez la notice d’utilisation du

moteur.

5. Nettoyez, réglez l’écartement ou

replacez la bougie.

6. Nettoyez la canalisation.

7. Attendez quelques minutes avant

d’essayer de faire démarrer le moteur

Le moteur surchauffe.

1. Faites le plein d’huile du carter.

2. Consultez la notice d’utilisation du

moteur.

3. Démontez l’habitacle du ventilateur et

nettoyez-le.

4. Consultez la notice d’utilisation du

moteur.

1. Niveau d’huile trop bas.

2. Le filtre à air est sale.

3. La circulation d’air est gênée.

4. La carburateur est mal régle.

Le moteur hésite parfois à

régime élevé.

1. Réglez l’écartement à 0,030 po. Con-

sultez la notice d’utilisation du moteur

2. Consultez la notice d’utilisation du

moteur.

1. La bougie est sale, défectueuse ou

l’écartement est trop grand.

2. Le carburateur est mal réglé.

3. Le filtre à air est sale.

1. L’écartement de la bougie est trop petit.

2. Mélange du ralenti du carburateur mal

réglé.

Le moteur tourne

irrégulièrement.

1. Réglez l’écartement à 0,030 po ou

remplacez la bougie. Consultez la

notice d’utilisation du moteur.

2. Consultez la notice d’utilisation du

moteur.

3. Consultez la notice d’utilisation du

moteur.

Vibrations excessives.

1. Serrez la lame et l’adaptateur.

Équilibrez la lame.

2. Remplacez la lame.

1. La lame est desserrée ou mal équilibrée.

2. La lame est déformée.

La coupe est irrégulière

1. Placez les quatre roues à la même

hauteur.

2. Aiguisez ou remplacez la lame.

1. Les roues ne sont pas bien

positionnées.

2. La lame est émoussée.

La tondeuse ne

déchiquette pas l’herbe.

1. Ne tondez pas quand l’herbe est mouil-

lée. Attendez qu’elle sèche.

2. Coupez l’herbe à un réglage élevé, puis

tondez à nouveau à la hauteur voulue ou

sur une largeur plus étroite.

3. Aiguisez ou remplacez la lame.

1. L’herbe est mouillée.

2. L’herbe est trop haute.

3. La lame est émoussée.

Entretien

Portez toujours

des gants épais ou

utilisez un chiffon

épais pour manipuler

la lame en la démon-

tant pour l’aiguiser ou

la remplacer.

Si la lame est

déséquilibrée,

elle fera vibrer la

tondeuse de façon

excessive, mais elle

pourrait aussi causer

des dommages

à la tondeuse

ou même casser

pendant qu’elle

tourne, et causer de

sérieuses blessures à

l’utilisateur.

Figure 5-2

3. Enlevez le boulon et le support de la lame qui

maintiennent la lame et l’adaptateur sur le vilebrequin.

Voir la Figure 5-2.

4. Dégagez la lame et l’adaptateur du vilebrequin.

5. Pour l’affûter à nouveau, démontez-la puis meulez

ou limez les bords tranchants en maintenant l’angle

aussi près que possible du biseau original. N’essayez

pas d’aiguiser la lame encore installée sur la

tondeuse.

6. Il est essentiel que chaque tranchant soit affûté

également pour ne pas avoir une lame déséquilibrée.

REMARQUE: Une lame déséquilibrée cause des vibra-

tions qui peuvent endommager le moteur et la tondeuse.

Assurez-vous de bien rééquilibrer la lame après l’avoir

aiguisée. Le fabricant de la tondeuse ne peut être tenu

responsable des dégâts causés par le mauvais équilibre

de la lame.

REMARQUE: Démontez toujours la lame de son

adaptateur pour vérifiez son bon équilibre.

7. Vous pouvez vérifier l’équilibre de la lame en la

plaçant sur un tournevis à tige ronde. Limez le métal

du côté le plus lourd jusquà ce que la lame soit

parfaitement équilibrée.

8. Avant de remonter la lame et son adaptateur sur

la tondeuse, lubrifiez le vilebrequin et la surface

intérieure de l’adaptateur avec une huile légère.

9. Placez l’adaptateur de la lame sur le vilebrequin,

«l’étoile» à l’opposé du moteur. Voir la Figure

5-2. Placez la lame, le côté sur lequel la mention

«Bottom» (ou le numéro de pièce) apparaît, à

l’opposé de l’adaptateur. Alignez le support de la lame

sur celle-ci en enfonçant les pattes dans les trous de

la lame, puis insérez le boulon hex.

10. Serrez le boulon hex. au couple recommandé

ci-dessous:

Couple de montage de la lame

Boulon centrale 450 po-lb min., 600 po-lb max.

Vérifiez périodiquement que TOUS les écrous et boulons

de la machine sont bien serrés.

Remplacement du déﬂecteur arrière

Il est installé sur l’arrière du plateau de coupe et a pour

but de minimiser les risques de projection d’objets vers le

conducteur. Remplacez le déflecteur arrière comme suit

s’il est endommagé.

1. Pour démonter le déflecteur arrière usagé, soulevez

le clapet arrière et pressez sur chaque côté du

déflecteur pour le dégager des trous. Voir la Figure

5-3.

2. Dégagez le déflecteur du trou opposé et remplacez-le

par le déflecteur neuf en appliquant les instructions

dans l’ordre inverse.

Le fait de couper

l’herbe sur un sol

sablonneux provoque

l’usure de la lame par

abrasion.

Remisage hors saison

Procédez de la manière suivante pour préparer votre

tondeuse pour un entreposage prolongé.

1. Nettoyez et lubrifiez soigneusement la tondeuse selon

les instructions de lubrification.

2. L’utilisation d’un nettoyeur sous pression ou d’un

boyau d’arrosage pour nettoyer la tondeuse est

déconseillée.

3. Consultez la notice d’utilisation du moteur quant aux

instructions d’entreposage du moteur.

4. Enduisez la lame de la tondeuse d’une graisse à

châssis pour l’empêcher de rouiller

5. Entreposez la tondeuse dans un endroit sec et propre.

Ne la remisez pas près de produits corrosifs, comme

des engraise.

REMARQUE: Il est très important de bien protéger le

matériel contre la rouille s’il doit être entreposé dans un

abri métallique non ventilé. Enduisez toute la machine,

en particulier les câbles et toutes les pièces mobiles,

avec une huile légère ou de la silicone.

AVERTISSEMENT

Figure 5-3

La page charge ...

Bolens 11A-549Q565 Le manuel du propriétaire

Marque: Bolens

Modèle: 11A-549Q565

Catégorie: Tondeuses à gazon

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 11A-549Q565 Owner's manual

Bolens 11A-549Q565 Le manuel du propriétaire

Bolens 11A-549Q565 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents