VTech ET685 Guide de démarrage rapide

Marque: VTech

Modèle: ET685

Catégorie: Téléphones

Taper: Guide de démarrage rapide

ErisTerminal® SIP Deskset

ET685

Quick Start Guide

Important Safety Information

This symbol is to alert you to important operating or servicing

instructions that may appear on the product or in this user’s manual.

Always follow basic safety precautions when using this product to

reduce the risk of injury, re, or electric shock.

WARNING: The product included (ITE) in this manual is to be connected only to

PoE networks without routing to the outside plant.

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of re, electric shock and injury, including the following:

1. This product should be installed by a qualied technician.

2. This product should only be connected to the host equipment and never

directly to the network such as Public Switch Telephone Network (PSTN) or

Plain Old Telephone Services (POTS).

3. Read and understand all instructions.

4. Follow all warnings and instructions marked on the product.

5. Unplug this product from the wall outlet before cleaning. Do not use liquid or

aerosol cleaners. Use a damp cloth for cleaning.

6. Do not use this product near water such as near a bath tub, wash bowl,

kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

7. Do not place this product on an unstable table, shelf, stand or other unstable

surfaces.

8. Slots and openings in the back or bottom of the telephone base and handset

are provided for ventilation. To protect them from overheating, these

openings must not be blocked by placing the product on a soft surface such

as a bed, sofa or rug. This product should never be placed near or over a

radiator or heat register. This product should not be placed in any area where

proper ventilation is not provided.

9. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supplied at the

premises, consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install this product

where the cord may be walked on.

11. Never push objects of any kind into this product through the slots in the

telephone base or handset because they may touch dangerous voltage

points or create a short circuit. Never spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this product, but

take it to an authorized service facility. Opening or removing parts of the

telephone base or handset other than specied access doors may expose

you to dangerous voltages or other risks. Incorrect reassembling can cause

electric shock when the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to an authorized

service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled onto the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operation instructions. Improper adjustment of other controls may

result in damage and often requires extensive work by an authorized

technician to restore the product to normal operation.

E. If the product has been dropped and the telephone base and/or

handset has been damaged.

F. If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an electrical storm.

There is a remote risk of electric shock from lightning.

16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under

certain circumstances, a spark may be created when the adapter is plugged

into the power outlet, or when the handset is replaced in its cradle. This is a

common event associated with the closing of any electrical circuit. The user

should not plug the phone into a power outlet if the phone is located in an

environment containing concentrations of ammable or ame-supporting

gases, unless there is adequate ventilation. A spark in such an environment

could create a re or explosion. Such environments might include: medical

use of oxygen without adequate ventilation; industrial gases (cleaning

solvents; gasoline vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next to your ear when it is in normal

talk mode.

18. The power adapters are intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

19. Use only the power adapter indicated in this manual.

Power adapter rating: 5 Vdc @ 2 A

20. For pluggable equipment, the socket-outlet shall be installed near the

equipment and shall be easily accessible.

21. In wall mounting position, make sure to mount the telephone base on the wall

by aligning the eyelets with the mounting studs of the wall plate. Then slide

the telephone base down on both mounting studs until it locks into place.

Refer to the full instructions in Deskset Installation in the User Guide.

22. CAUTION: Keep small metallic objects such as pins and staples away from

the handset receiver.

SAVE THESE INSTRUCTIONS

For UL compliance only

Mesures de sécurité importantes

Ce symbole vous alertera d’informations importantes ou d’instructions d’entretien

pouvant apparaître dans ce guide d’utilisation. Respectez toujours

les mesures de sécurité et de sécurité de base lorsque vous utilisez

ce produit, an de réduire les risques de blessures, d’incendie, ou

d’électrocution.

Mesures de sécurité importantes

An de réduire les risques d’incendie, de blessures corporelles ou

d’électrocution, suivez toujours ces mesures préventives de base lorsque vous

utilisez votre téléphone :

1. Cet appareil doit être installé par un technicien qualié.

2. Cet appareil doit être branché à un équipement hôte et jamais branché à un

réseau, tel qu’un réseau PSTN publique ou un réseau téléphonique standard

(POTS).

3. Lisez et comprenez bien toutes les instructions.

4. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

5. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez

pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chion doux et

légèrement humecté.

6. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo,

d’un évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-

sol humide ou sous la douche.

7. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.

L’appareil pourrait tomber et être sérieusement endommagé.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées

à l’arrière ou en dessous. An d’empêcher la surchaue, ces ouvertures ne

doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis ou

autre surface similaires. Ne placez pas cet appareil à proximité d’un élément

de chauage ni d’une plinthe électrique. De plus, ne l’installez pas dans une

unité murale ou un cabinet fermé qui ne possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur

les étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre

maison, consultez votre marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans

un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne

d’alimentation ni le cordon téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet

appareil, car ils pourraient toucher à des points de tension dangereux

ou court-circuiter des pièces, ce qui constituerait un risque d’incendie ou

d’électrocution. N’échappez pas de liquides dans l’appareil.

12. An de réduire les risques d’électrocution, ne démontez pas l’appareil, mais

apportez-le plutôt à un centre de service qualié s’il doit être réparé. En

enlevant le couvercle, vous vous exposez à des tensions dangereuses ou

autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation ultérieure de l’appareil.

13. Ne surchargez pas les prises de courant ni les rallonges électriques, car ceci

peut constituer un risque d’incendie ou d’électrocution.

14. Débranchez cet appareil de la prise de courant et communiquez avec le

département de service à la clientèle de VTech dans les cas suivants:

A. Lorsque le cordon d’alimentation est endommagé ou écorché.

B. Si du liquide a été échappé dans l’appareil.

C. Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

D. Si l’appareil ne fonctionne pas normalement en suivant les directives

du guide. N’ajustez que les commandes couvertes dans le guide

d’utilisation, car un mauvais réglage de celles-ci peut être à l’origine de

dommages, ce qui nécessiterait des réparations considérables pour

remettre l’appareil à son état de fonctionnement normal.

E. Si l’appareil a été échappé ou son boîtier, endommagé.

F. Si le produit ache une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans l) pendant un orage. Les

éclairs peuvent être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de

celle-ci. Sous certaines circonstances, une inteincelle pourrait survenir

lorsque l’adaptateur est branché à une prise de courant, ou lorsque le

combiné est déposé sur le combiné. Ceci est un événement commun associé

avec la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher

le téléphone dans une prise de courant, et ne devrait pas déposer le combiné

chargé sur le socle, si le téléphone se trouve dans un environnement ou la

concentration de gaz inammables, sans ventilation adéquate. Une étincelle

dans ces endroits pourrait provoquer un incendie ou une explosion. Ces

environnements pourraient être l’utilisation médicale de l’oxygène sans

ventilation adéquate; le gaz industriel (dissolvants, vapeurs d’essence, etc.);

une fuite de gaz naturel, etc.

17. Placez uniquement le combiné de votre appareil près de votre oreille lorsqu’il

est en mode de conversation normal.

18. Les adaptateurs sont conçus pour être orientés en position verticale ou en

position horizontale sur le plancher.

19. N’utilisez que cordon d’alimentation et les piles indiquées dans ce guide

d’utilisation.

Note de l’adaptateur: 5 Vdc @ 2 A

20. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise

de courant doit être installée près du produit, an d’assurer une accessibilité

sécuritaire à la prise de courant.

21. En position de montage mural, assurez-vous de monter le socle du téléphone

sur le mur en alignant les oeillets avec les goujons de xation de la plaque

murale. Ensuite, faites glisser le socle vers le bas sur les deux goujons de

xation jusqu’à ce qu’il se verrouille en place. Reportez-vous aux instructions

complètes dans la section Installation dans ce guide d’utilisation.

22. MISE EN GARDE : Éloignez les petits objets métalliques tels que les broches

de l’écouteur du combiné.

CONSERVEZ CES INSTRUCTIONS

FCC part 15

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at the user’s expense.

WARNING: Changes or modications to this equipment not expressly approved

by the party responsible for compliance could void the user’s authority to operate

the equipment.

RF Radiation Exposure

This SIP Deskset complies with FCC RF radiation exposure limits set forth for an

uncontrolled environment.

Caution: To maintain the compliance with the FCC’s RF exposure guideline, place

the SIP Deskset at least 20cm from nearby persons.

Industry Canada

This Class A digital apparatus complies with Canadian requirements:

CAN ICES-3 (A)/NMB-3(A).

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du

Canada.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certication/registration number only signies that the

Industry Canada technical specications were met.

This product meets the applicable Innovation, Science and Economic

Development Canada technical specications.

RF Radiation Exposure

This SIP Deskset also complies with Industry Canada RSS-102 with respect to

Canada’s Health Code 6 for Exposure of Humans to RF Fields.

Parts Checklist

Your telephone package contains the following items. Save your sales receipt

and original packaging in the event warranty service is necessary.

About this Guide

This quick start guide provides a reference for the external features of the phone

and basic installation instructions.

Please refer to the ET685 Deskset User Guide for complete installation and

operation instructions. You can download the guide from

businessphones.vtech.com.

For customer service or product information, visit our website at

businessphones.vtech.com or call 1 (888) 370-2006.

Quick Start Guide

Handset and

handset cord

Deskset base Deskset stand

Ethernet cable

Quick

Start

Guide

Quick Reference Guide

External Features and Controls

SCREEN

FUNCTION KEYS

NAVIGATION KEYS

CALL LED

CASING

MICROPHONE

AUDIO

CONTROL

KEYS

MWI KEY with LED

PROGRAMMABLE

KEYS P1-P6 with

FUNCTION KEY

SCREEN

ALPHANUMERIC

KEYPAD

DEDICATED,

CUSTOMIZABLE

FUNCTION KEYS

PAGES KEY for

FUNCTION KEY

SCREEN

Deskset Installation

This section assumes that your network infrastructure is established and that

your IP PBX phone service has been ordered and congured for your location.

For more information about installation options and phone setup, see the ET685

Deskset User Guide and the ET685 Deskset Administrator and Provisioning

Manual, available at businessphones.vtech.com.

You can power the phone using a compatible VTech AC power adapter or using

Power over Ethernet (PoE) from your network. (The phone requires PoE Class 2.) If

you are not using PoE, install the phone near a power outlet not controlled by a wall

switch. The phone can be placed on a at surface or vertically mounted on the wall.

Avoid placing the deskset too close to:

• Communication devices such as television sets, DVD players, or other

cordless telephones

• Excessive heat sources

• Noise sources such as a window with trac outside, motors, microwave

ovens, refrigerators, or uorescent lighting

• Excessive dust sources such as a workshop or garage

• Excessive moisture

• Extremely low temperature

• Mechanical vibration or shock such as on top of a washing machine or work

bench.

Attaching the Footstand

2 3

Connecting the phone

(2, 3)

(1, 2)

(2, 3)

EHS

(1) If no PoE available

(2)

Not included in delivery

(3)

Oponal

Connecting the phone

The phone can be operated with Power over Ethernet (PoE) provided via the

network cable or, if PoE is not available in your network, with the separately

available 5V DC VTech power adapter VSP-PWR2000.

• Plug the Ethernet (network) cable into the RJ45 connector labeled “NET”,

and plug the other end into the network side to establish a data link.

If PoE is not available, insert the plug of the power supply into the connector

labeled “5V DC” and hook up the plug to the wall outlet.

• The second RJ45 connector, labeled “PC”, is for daisy-chaining further

Ethernet devices without the need for a second Ethernet connection line.

IMPORTANT INFORMATION

1. Use only a compatible VTech power adapter. To order a power adapter, visit

our website at businessphones.vtech.com or call 1 (888) 370-2006.

2. The power adapter is intended to be correctly oriented in a vertical or oor

mount position. The prongs are not designed to hold the plug in place if it is

plugged into a ceiling, under-the-table or cabinet outlet.

Initializing and registering the phone

Please note: You will need the registration information received from your

Internet service provider or your network administrator - normally the phone or

extension number, the password, and the registrar.

After you have set up the phone and connected it to the network as shown on

page 13, the phone begins to initialize. Normally the initialization is completely

automatic, using DHCP.

If your network does not support DHCP, you must obtain the IP address,

netmask, IP gateway, and DNS server from your Internet service provider or your

network administrator and enter them manually when you are asked to do so on

the display.

Watch the display and, when prompted, make selections by pressing the

up or down arrow on the navigation key .

Save your selection by pressing the OK key .

1. Language. The default is English.

2. Time zone. Press the function key underneath to go to the next time

zone, then

to show all available options within that time zone.

3. Tone Scheme (dial tone).

4. The display shows the “Welcome” screen. Press any key to log on.

NOTE: To view the phone’s IP address at this state, press .

5. Enter the account number. Press to save.

6. Enter the registrar. Press to save.

7. Enter the password received from your Internet service provider or

administrator. Press to save. After successful registration, you will see

the idle screen.

For further information, please refer to the ET685 User Guide.

Maintenance

Taking care of your telephone

• Your telephone base contains sophisticated electronic parts, so you must

treat it with care.

• Avoid rough treatment.

• Place the corded handset down gently.

• Save the original packing materials to protect your telephone base if you ever

need to ship it.

Avoid water

• You can damage your telephone base if it gets wet. Do not use the corded

handset in the rain, or handle it with wet hands. Do not install the telephone

base near a sink, bathtub or shower.

Electrical storms

• Electrical storms can sometimes cause power surges harmful to electronic

equipment. For your own safety, take caution when using electric appliances

during storms.

Cleaning your telephone

• Your telephone base has a durable plastic casing that should retain its luster

for many years. Clean it only with a soft cloth slightly dampened with water or

a mild soap.

• Do not use excess water or cleaning solvents of any kind.

Remember that electrical appliances can cause serious injury if used when

you are wet or standing in water. If the telephone base should fall into water,

DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND

TELEPHONE LINE CORDS FROM THE WALL, then pull the unit out by the

unplugged cords.

Technical Specications

Operating temperature 32–104 °F (0–40 °C)

AC adapter output voltage 5.0 Vdc @ 2 A

AC adapter model number VTech model #: VSP-PWR2000

SIL model #: SSA-050200US

Ten Pao model # S018BAM0500200

Connectors 2 x RJ45 (1 x LAN, 1 x PC)

2 x 4P4C (handset, optional wired headset)

1 x USB 2.0 type A

1 x proprietary connector for Expansion module

Ethernet 2 x IEEE 802.3 / 1 Gigabit switch

VTECH COMMUNICATIONS LTD.

A member of THE VTECH GROUP OF COMPANIES.

Distributed in the U.S.A. by VTech Communications Inc., Beaverton, Oregon 97008.

VTech is a registered trademark of VTech Holdings Limited.

Printed in China. Version 2, 05/18

VTech ET685 Guide de démarrage rapide

Marque: VTech

Modèle: ET685

Catégorie: Téléphones

Taper: Guide de démarrage rapide

Télécharger le PDF

rapport

dans d''autres langues

English: VTech ET685 Quick start guide

Documents connexes

Autres documents

Snom M500 Quick Installation Guide