For technical questions call 1-800-665-8685 1

WARNING! Read and understand all instructions before using this

device. The operator must follow basic precautions to reduce the

risk of personal injury and/or damage to the equipment.

NOTE: Keep this manual for safety warnings, precautions, operating

or inspection and maintenance instructions.

WORK AREA

1. Operate in a safe work environment. Keep your work area

CAUTION! Wear personal protective equipment approved by

the Canadian Standards Association (CSA) or American National

Standards Institute (ANSI).

Personal Protective Equipment

1. Always wear impact safety goggles that provide front and

side protection for the eyes.

2. Wear gloves that provide protection based on the

work materials.

User Manual

2 to 5 in. Bore Implement/Utility

4. Wear steel toe footwear or steel toe caps to prevent injury

from falling objects.

HYDRAULIC SAFETY

Hydraulic fluid has a low level of toxicity and should not cause irritation

or injury under normal use. Follow these safety instructions if personal

contamination occurs.

1. Eyes - Flush eyes with water for 15 minutes with eyelids

open. Seek medical attention if irritation continues.

2. Skin - Wipe excess oil away and wash with mild soap and

water for 15 minutes. If irritation continues, seek

amounts are ingested. DO NOT induce vomiting. If vomiting

occurs spontaneously, place head below hips to prevent

aspiration of liquids into the lungs.

5. Inhalation - Inhalation of oil mist or vapors from hot oil may

cause irritation of the upper respiratory tract. Remove from

exposure and vent area. Additional first aid should not

be required.

PARTS IDENTIFICATION

Remove the parts and accessories from the packaging and inspect for

5. Shaft Polyoxymethylene Back Up Washer

6. Shaft Hallite 605 Twin Lip Seal

7. Threaded Head Nitrile O-Ring Seal

8. Shaft Hallite 520 Wiper Seal

* This kit contains extra seals for different shaft sizes.

* The seals have been improved but will fit all versions

of cylinders.

1. Disassemble the cylinder

a. Open both ports and drain all the oil from

piston from the cylinder as this could result in serious injury

or death.

d. Remove the piston from the rod by removing the

e. Slide the cylinder head off of the rod

2. Seal replacement

a. Lubricate the seals with hydraulic oil prior to

b. Be careful not to cut or damage the seals when

d. Install the cylinder head and torque according to

TABLE 1

for proper disposal instructions or locations.

outil avec alésage de 2 à 5 po

Manuel d'utilisateur

AVERTISSEMENT ! Veuillez lire et vous assurer de comprendre

toutes les instructions avant d’utiliser cet appareil. L’utilisateur

doit respecter les précautions de base afin de réduire le risque de

blessure et/ou de dommage à l’équipement.

REMARQUE : Conservez ce manuel qui contient les avertissements

2. Assurez-vous que les personnes qui ne portent pas

l’équipement de sécurité approprié ne se trouvent pas à

proximité de l’aire de travail.

3. Rangez les outils correctement dans un lieu sécurisé et sec.

Gardez les outils hors de la portée des enfants.

SÉCURITÉ PERSONNELLE

ATTENTION ! Portez de l’équipement de protection homologué

par l’Association canadienne de normalisation (CSA) ou l’American

National Standards Institute (ANSI).

Équipement de protection personnel

2. Portez des gants qui protègent en fonction des matériaux

de travail.

3. Les chaussures antidérapantes sont recommandées

pour maintenir la stabilité et l’équilibre au sein de

l’environnement de travail.

4. Portez des chaussures à embout d’acier ou à coquilles

d’acier pour éviter les blessures dues à la chute d’objets.

SÉCURITÉ HYDRAULIQUE

Le liquide hydraulique présente un faible degré de toxicité et ne

devrait causer aucune irritation ou blessure lors de son utilisation