Parkside PMTS Manuel utilisateur

METAL CUTTING CHOP SAW / METALL-

TRENNSCHLEIFER / TRONÇONNEUSE À MÉTAUX

PMTS 180 A1

TRONÇONNEUSE À MÉTAUX

Traduction des instructions d’origine

METALL-TRENNSCHLEIFER

Originalbetriebsanleitung

METAL CUTTING CHOP SAW

Translation of the original instructions

ŘEZNÁ BRUSKA NA KOV

Překlad originálního provozního návodu

METAAL-DOORSLIJPMACHINE

Vertaling van de originele gebruiksaanwijzing

REZNÁ BRÚSKA NA KOV

Preklad originálneho návodu na obsluhu

SZLIFIERKA KĄTOWA DO METALU

Tłumaczenie oryginalnej instrukcji obsługi

TRONZADORA DE METAL

Traducción del manual de instrucciones original

KAPSAV

TIL METAL

Oversættelse af den originale driftsvejledning

IAN 373210_2104

GB Translation of the original instructions Page 1

DE Originalbetriebsanleitung Seite 15

FR Traduction des instructions d’origine Page 29

NL Vertaling van de originele gebruiksaanwijzing Pagina 45

CZ Překlad originálního provozního návodu Strana 59

PL Tłumaczenie oryginalnej instrukcji obsługi Strona 73

SK Preklad originálneho návodu na obsluhu Strana 87

ES Traducción del manual de instrucciones original Página 101

DK Oversættelse af den originale driftsvejledning Side 117

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of

the device.

Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen

Funktionen des Gerätes vertraut.

Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec

toutes les fonctions de l‘appareil.

Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het

apparaat.

Před čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi

funkcjami urządzenia.

Pred čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Antes de empezar a leer abra la página que contiene las imágenes y, en seguida, familiarícese con todas

las funciones del dispositivo.

Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.

A

C

B

14a

PMTS 180 A1 GB│IE │ 1 ■

Contents

Introduction ............................................................2

Intended use ........................................................................2

Features ...........................................................................2

Package contents ....................................................................2

Technical data ......................................................................3

General Power Tool Safety Warnings ......................................3

1. Work area safety ..................................................................4

2. Electrical safety ...................................................................4

3. Personal safety ....................................................................4

4. Power tool use and care ............................................................5

5. Service ..........................................................................5

Safety instructions for abrasive cutting appliances ............................ 5

1) Safety instructions for abrasive cutting appliances ........................................5

2) Kickback and corresponding safety instructions ..........................................6

Further safety instructions forabrasive cutters ...............................7

Original accessories/auxiliary equipment ................................................10

Before use ............................................................10

Setting up the appliance .............................................................10

Removing/inserting transport safetydevices ..............................................10

Operation ............................................................10

Switching on and oﬀ ................................................................10

Setting the cutting depth ..............................................................10

Changing the cutting disc .............................................................10

Clamping the workpiece .............................................................11

Cleaning and maintenance ..............................................11

Disposal ..............................................................12

Kompernass Handels GmbH warranty ....................................12

Service ............................................................... 13

Importer .............................................................13

Translation of the original Conformity Declaration ...........................14

PMTS 180 A1

■ 2 │ GB│IE

METAL CUTTING CHOP SAW

PMTS 180 A1

Introduction

Congratulations on the purchase of your new

appliance. You have chosen a high-quality product.

The operating instructions are part of this product.

They contain important information about safety,

usage and disposal. Before using the product,

please familiarise yourself with all operating and

safety instructions. Use the product only as

described and for the range of applications speci-

ﬁed. Please also pass these operating instructions

on to any future owner.

Intended use

The cut-oﬀ grinder is intended as a ﬂoor-mounted

appliance for making straight longitudinal cuts at

up to 45° using cutting discs in steel, nonferrous

metals, cast iron and iron proﬁles without the use

of ater.

Any other uses of or modiﬁcations to the machine

are deemed to be improper usage and may result

in serious physical injury.

Not for commercial use.

Features

ON/OFF switch

Clamping ﬂange (inside)

Spindle lock

Cutting disc

Rapid adjustment

Vice

Drillholes

Cutting angle adjustment

Transport safety device

Cutting depth adjustment

Motor unit

Handle

Figure A

Pendulum cover

Protective cover

14a Integrated carrying handle

Mounting screws

Figure B

Clamping ﬂange (outside)

Plain washer

Fixing nut

Figure C

Hex key (large)

Hex key (small)

Package contents

1 metal cutting chop saw PMTS 180 A1

1 cutting disc Ø 180 mm (pre-ﬁtted)

2 Hex keys

1 set of operating instructions

PMTS 180 A1 GB│IE │ 3 ■

Technical data

Rated voltage 230 V ∼, 50 Hz

(alternating current)

Rated power consumption 1280 W

Rated idle speed n0 7700 rpm

Cutting disc mounting Ø 22.23 mm

Thread size M8

Maximum speed of the cutting

disc 8500 rpm

Working speed of the cutting

disc max. 80 m/s

Cutting disc diameter Ø 180 mm

Cutting disc thickness 1.6 mm

Inclined cuts 0°–45°

max. cut depth

50mm

50 mm at 0°

mitre angle

Protection class II / (double

insulation)

Noise emission value

Noise measurement value determined in accord-

ance with EN 62841. The A-rated noise level of

the power tool is typically as follows:

Sound pressure level LPA = 93 dB(A)

Uncertainty KPA = 3 dB

Sound power level LWA = 106 dB (A)

Uncertainty KWA = 3 dB

Wear hearing protection!

WARNING!

► Depending on the manner in which the

power tool is being used and, in particular,

the kind of workpiece that is being worked,

the vibration and noise emission values can

deviate and may sometimes exceed the

values given in these instructions. Regular use

of the power tool in this way may cause the

user to underestimate the vibration. Try to

keep the vibration loads as low as possible.

Measures to reduce the vibration load are,

e.g. wearing gloves and limiting the working

time. Wherein all states of operation must be

included (e.g. times when the power tool is

switched oﬀ and times where the power tool

is switched on but running without load).

General Power Tool

Safety Warnings

WARNING!

►Read all safety warnings, instructions,

illustrations and speciﬁcations provided

with this power tool. Failure to follow all

instructions listed below may result in electric

shock, ﬁre and/or serious injury.

Save all warnings and instructions for future

reference.

The term „power tool“ in the warnings refers to

your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

PMTS 180 A1

■ 4 │ GB│IE

1. Work area safety

a) Keep work area clean and well lit. Cluttered

or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded)

power tools. Unmodiﬁed plugs and matching

outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired

or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such

as a dust mask, non-skid safety shoes, hard hat

orhearing protection used for appropriate condi-

tions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools

with your ﬁnger on the switch or energising

power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or

long hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use

of dust collection can reduce dust-related

hazards.

h) Do not let familiarity gained from frequent

use of tools allow you to become complacent

and ignore tool safety principles. A careless

action can cause severe injury within a fraction

of a second.

PMTS 180 A1 GB│IE │ 5 ■

4. Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at

the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ. Any power tool that

cannot be controlled with the switch is dangerous

and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detach-

able, from the power tool before making any

adjustments, changing accessories, or storing

power tools. Such preventive safety measures

reduce the risk of starting the power tool acci-

dentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation.

Ifdamaged, have the power tool repaired

before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed. Use of the

power tool for operations diﬀerent from those

intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unex-

pected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

Safety instructions for

abrasive cutting appliances

1) Safety instructions for abrasive

cutting appliances

a) Ensure that you and everyone else in the

vicinity remain outside of the range of the

rotating grinding disc. The blade guard is

designed to protect the operator from fragments

and accidental contact with the grinding tool.

b) Use only reinforced bonded or diamond-

coated cutting discs for your power tool. Just

because you can attach the accessories to your

power tool does not guarantee they are safe to

use.

c) The permissible speed of the accessory tool

used must be at least as high as the maximum

speed speciﬁed for the power tool. Accesso-

ries that rotate faster than the permissible rate

can break and throw pieces into the air.

d) Grinding tools should only be used for the

recommended applications. For example:

Never grind with the side surface of a cutting

disc. Cutting discs are designed to remove

material with the edge of the disc. Any lateral

application of force on these grinding tools can

lead to a breakage.

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc

breakage.

f) The external diameter and thickness of the

attachment part used must comply with the

dimensions of the power tool. Incorrectly

dimensioned accessory tools cannot be suﬃ-

ciently shielded or controlled.

PMTS 180 A1

■ 6 │ GB│IE

g) Grinding discs and ﬂanges must ﬁt precisely

onto the grinding spindle of your power tool.

Accessory tools which do not ﬁt precisely on the

grinding spindle of the power tool will rotate

unevenly, vibrate severely and can lead to a

loss of control.

h) Do not use damaged grinding discs. Check

the grinding discs before each use for chips

and cracks. If the power tool or grinding disc

is dropped, check to see if either are

damaged or use an undamaged grinding

disc. After checking and inserting the

grinding disc, ensure that you and any other

people in the vicinity remain outside of the

range of the rotating grinding disc and allow

the tool to rotate at maximum speed for one

minute. Damaged grinding discs usually break

during this test period.

i) Wear personal protective equipment.

Depending on the application, ensure that

you use full face protection, eye protection or

goggles. If required, use a dust mask, ear

protectors, protective gloves or special apron

to protect you from grindings and material

particles. The eye protection must be worn to

protect you against ﬂying debris, which may be

caused by the various applications. Dust or ﬁlter

masks must be used to ﬁlter any dust created by

the application. If you are exposed to loud

noise for any length of time, you can suﬀer a

hearing loss.

j) Ensure that other people remain at a safe

distance to your workspace. Anyone who

enters the workspace must wear personal

protective equipment. Fragments of the work-

piece or broken accessory tools can ﬂy oﬀ and

cause injury – even outside the immediate

working area.

k) Keep the power cable away from any

rotating accessories. If you lose control of the

appliance, the connecting cable may get cut or

caught and your hand or arm could get caught

in the rotating accessory tool.

l) Clean the ventilation slits in your power tool

regularly. The engine fan draws dust into the

housing and a strong accumulation can cause

electrical hazards.

m) Do not use the power tool near ﬂammable

materials. Do not use the electrical appliance

if it is placed on a ﬂammable surface such as

wood. Sparks can ignite such materials.

n) Do not use any attachment parts that require

liquid coolant. The use of water or other liquid

coolants may lead to an electric shock.

2) Kickback and corresponding

safety instructions

Kickback is a sudden reaction caused when a

rotating cutting disc catches or jams. Catching or

jamming causes the rotating accessory tool to stop

abruptly. This results in an uncontrolled cutting

grinding tool being accelerated upwards towards

the operator.

If, for example, a cutting disc catches or jams, the

edge of the cutting disc that is projecting into the

workpiece can get caught and break oﬀ the cutting

disc or cause a kickback. This can also break

cutting discs.

A kickback is caused by improper or incorrect use

of the power tool. This can be avoided by taking

proper precautions as given below.

a) Hold the power tool ﬁrmly in both hands and

position your body and arms so that they can

absorb the kickback forces. By taking

adequate precautions, the operator can stay in

control of the kickback and reaction torques.

b) Avoid the area in front of and behind the

rotating cutting disc. In cases of kickback, an

uncontrolled cutting grinding tool is driven

upwards towards the operator.

PMTS 180 A1 GB│IE │ 7 ■

c) Do not use a toothed, wood-cutting or chain

saw blade or segmented diamond-coated

disc with more than 10 mm wide gaps. Such

accessories often cause a kickback or loss of

control over the power tool.

d) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or blocking and

thus the possibility of a setback or a breakage

of the grinding tool.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold the cutting appli-

ance steady until the disc has completely

stopped turning. Never attempt to pull a

rotating cutting disc out of a cut. This could

lead to a kickback. Identify and remove the

cause of the jam.

f) Do not switch the power tool back on for as

long as it is in the workpiece. Allow the

cutting disc to reach its full speed before you

carefully continue the cut. Otherwise, the disc

can jam, jump out of the workpiece or cause

kickback.

g) Support large workpieces to reduce the risk

of the cutting disc jamming and causing a

kickback. Large workpieces can bend under

their own weight. The workpiece must be

supported on both sides, namely in the vicinity

of the cut, and also at the edge.

Further safety instructions

forabrasive cutters

■Never stand on an electrical appliance.

Serious injuries can occur if the electrical appli-

ance tips over or if you inadvertently come into

contact with the cutting disc.

■Always use the protective cover. A protective

cover protects the user against parts of the

cutting disc which have broken oﬀ and also

against unintentional contact with the cutting

disc.

■Ensure that the protective cover is working

properly and that it can move freely. Never

clamp the protective cover when it is in the open

position.

■Use the appliance only for dry cutting.

Water entering a power tool will increase the

risk of electric shock.

■Keep the power cable away from any

rotating accessories. The power cable can be

cut through or caught up.

■Keep handles dry, clean and free from oil

and grease. Greasy, oily handles are slippery

and result in loss of control.

■Never remove cutting leftovers, metal swarf

etc. from the cutting area while the power

tool is running. Always place the tool arm in

the idling position and switch the power tool oﬀ.

■Always switch on the power tool before

applying it to the workpiece. Otherwise, there

is a danger of kickback if the cutting disc

becomes caught up in the workpiece.

■Only use the power tool if the working surface

is free of all adjusting tools, metal swarf etc.

except for the workpiece to be processed.

Small pieces of metal or other objects which

come into contact with the rotating cutting disc

can hit the operator at high speed.

PMTS 180 A1

■ 8 │ GB│IE

■Always clamp the workpiece to be processed

ﬁrmly. Never use workpieces which are too

small to clamped ﬁrmly. The distance between

your hand and the rotating cutting disc is other-

wise too small.

■If the cutting disc jams, switch the power tool

oﬀ and wait until the cutting disc has

completely stopped turning. Never attempt to

pull a rotating cutting disc out of a cut. This

could lead to a kickback. Identify and remove

the cause of the jam.

■Do not apply lateral pressure to try and slow

the cutting disc down after switching oﬀ the

appliance. The cutting disc might be damaged,

break or cause a kickback.

■Never ram the cutting disc into the workpiece

forcefully, and never apply too much force

when using a power tool. You should espe-

cially avoid jamming the cutting disc when

working on corners, sharp edges etc. If the

cutting disc is damaged by misuse, it can form

cracks that result in sudden breakage.

■Wear a safety apron. Ensure that nobody

can be endangered by ﬂying sparks. Remove

all ﬂammable material from the vicinity.

Grinding metal creates ﬂying sparks.

■Only use the abrasive cutter for materials

speciﬁed in the instructions for proper use.

Otherwise, the abrasive cutter can be over-

loaded.

■Never use any damaged, non-circular or

vibrating cutting discs. Damaged cutting discs

cause increased friction, jamming of the cutting

disc and kickback.

■Always use cutting disks of the correct size

and with an appropriate central ﬁxing bore

(e.g. diamond-shaped or circular). Cutting

disks which do not match the ﬁtting parts on the

abrasive cutter will run eccentrically and cause

loss of control.

■Do not use chains or toothed saw blades.

Such accessories often cause a kickback or loss

of control over the power tool.

■Observe the operating manual published by

the cutting disc manufacturer when ﬁtting and

using the cutting disc. Unsuitable cutting disks

can lead to personal injury and may cause

snagging, tearing of the disc or kickback.

■Do not use any accessories that have not been

speciﬁcally provided or recommended by the

manufacturer for this power tool. Just because

you can attach the accessories to your power

tool does not guarantee they are safe to use.

■Do not touch the cutting disks after work until

they have cooled down. Cutting discs become

very hot while they are working.

■Check the cable regularly. Damaged cables

may only be repaired by an authorised

customer service location for power tools.

Replace any damaged extension cables. This

will ensure that the safety of the power tool is

maintained.

■Store unused power tools safely. The storage

location must be dry and lockable. This

prevents the power tool being damaged by

storage or being used by inexperienced

persons.

■Secure the workpiece! A workpiece securely

held by a clamping device or vice is much safer

than one held in your hand.

■Never leave the tool until it has come to a

complete standstill. Power tools which continue

to run on can cause injuries.

■Do not use the power tool with a damaged

cable. Never touch a damaged cable and

remove the plug from the mains socket if the

cable becomes damaged during work.

Damaged cables increase the risk of electric

shock.

PMTS 180 A1 GB│IE │ 9 ■

Supplementary notes

■ Always wear eye and ear protectors. Use

other protective equipment such as dust masks,

protective gloves, protective goggles if neces-

sary.

■ Never use any cutting discs with spalling, cracks

or other damage.

■ Always visually inspect cutting discs before

each use.

■ Do not use any saw blades.

■ Never use the appliance without the disc guard.

WARNING!

DANGER DUE TO DUST EXPOSURE!

► When working for extended periods of time

on wood and, in particular, materials that

produce dust which is hazardous to health,

connect the appliance to an appropriate

external dust extraction appliance.

Symbols used on the power tool

Keep your hands clear of the

cutting area while the power tool is

running. There is a danger of injury if

you contact the cutting disc.

Wear protective gloves!

Wear a dust mask!

Wear protective goggles!

Wear hearing protection!

Wear safety shoes!

Not designed for wet grinding

Use of damaged cutting or polishing

discs is dangerous and can lead to

serious injuries!

Intended for metal grinding

80 Disc diameter

Before using the device for the ﬁrst

time, read the original operating

instructions and safety instructions.

Metal cut-oﬀ grinder

WARNING! TOXIC FUMES!

► Working with the tool can produce harmful/

toxic dusts that represent a health hazard for

the person operating the appliance and for

any other people in the area.

PMTS 180 A1

■ 10 │ GB│IE

Original accessories/auxiliary

equipment

■ Use only the additional equipment and accesso-

ries speciﬁed in the operating instructions. Using

attachments or accessory tools other than those

recommended in the operating instructions can

lead to a risk of injury.

Before use

Setting up the appliance

Fix the appliance using suitable bolts (not included

in delivery) to a ﬂat, stable base. Use the drill

holes for this purpose. Ensure that a mains

socket is within easy reach.

NOTE

► In exceptional cases you can position the

baseplate for this process on a solid support.

Removing/inserting transport

safetydevices

Removing transport safety devices

♦ Apply a little pressure to the handle and

pull the transport safety device out. The

motor unit can now be moved upwards.

Inserting transport safety devices

♦ Press the handle downwards and push the

transport safety device into the appliance.

The motor unit is now ﬁxed.

NOTE

► Use the transport safety device for trans-

porting the appliance. Carry the appliance

by its integrated carrying handle 14a .

Operation

Switching on and oﬀ

■ Direction of rotation of the tool!

■ Insert the plug into a mains power socket.

Switching on

♦ Press the ON/OFF switch and keep it

pressed.

Switching oﬀ

♦ Release the ON/OFF switch .

Setting the cutting depth

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work on

the appliance.

♦ Adjust the screw on the cutting depth adjust-

ment with the aid of the supplied hex key

(small) .

♦ Test the cutting depth by lowering the motor

unit.

Changing the cutting disc

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work on

the appliance.

►Allow the cutting disc to cool down

before you touch it

►Check the cutting disc . It should not be

damaged or damp, and it should have no

cracks. Otherwise, it could break during

use and cause injuries.

NOTE

► Only use cutting disks which comply with the

performance data stated in this manual.

♦ Undo the mounting screws using the

supplied hex key (small) , in order to remove

the protective cover .

PMTS 180 A1 GB│IE │ 11 ■

♦ Swing the pendulum cover back completely

and hold it ﬁrmly in place with your hand.

♦ Press the spindle lock all the way down and

hold it in this position. If necessary, rotate the

cutting disc by hand until this is possible.

♦ Use the hex key supplied (large) to unscrew

the ﬁxing nut out in an anticlockwise direc-

tion.

♦ Remove the plane washer , the clamping

ﬂange (outside) and the cutting disc .

♦ Insert a new cutting disc.

♦ Proceed in reverse order in order to reassemble

the appliance to a usable condition.

♦ Check whether all the fastening elements are

correctly ﬁtted.

NOTE

► Ensure that the cutting disc can be rotated

freely.

► Switch the appliance on for around 60seconds

to check that there are no unusual vibrations.

If this is not the case, you should check that

the cutting disc is installed correctly .

Clamping the workpiece

You can clamp the workpiece and adjust the mitre

angle with the aid of the ﬁtted vice.

Using the vice

♦ Turn the handle on the vice clockwise to

clamp the workpiece.

♦ Turn the handle on the vice anticlockwise to

unclamp the workpiece.

NOTE

► You can also fold the rapid adjustment

upwards in order to make a quick adjustment

to the vice . Fold the rapid adjustment

down again in order to ﬁx the vice . After

this, use the vice handle to make ﬁne

adjustments.

Setting the cutting angle (mitre angle)

♦ Undo the cutting angle adjustment by turning

it anticlockwise. If necessary, pull the cutting

angle adjustment upwards.

♦ Set the required cutting angle using the angle

given.

♦ Retighten the cutting angle adjustment by

turning it clockwise.

Cleaning and maintenance

WARNING! RISK OF INJURY!

►Always remove the power plug from the

wall socket before carrying out any work on

the appliance.

■ The appliance must always be kept clean, dry

and free from oil or grease.

■ Use a soft, dry cloth to clean the housing.

■ Clean the ventilation slits in your power tool

with a soft brush regularly.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

► Required maintenance work should only be

replaced by qualiﬁed service personnel.

PMTS 180 A1

■ 12 │ GB│IE

Disposal

The packaging is made from environ-

mentally friendly material and can be

disposed of at your local recycling

plant.

Do not dispose of power tools

in your normal domestic waste!

European Directive 2012/19/EU

requires that worn-out power tools be

collected separately and recycled in an environ-

mentally compatible manner.

Dispose of the packaging in an envi-

ronmentally friendly manner. Note

the labelling on the packaging and

separate the packaging material

components for disposal if necessary. The pack-

aging material is labelled with abbreviations (a)

and numbers (b) with the following meanings:

1–7: plastics, 20–22: paper and cardboard,

80–98: composites.

Your local community or municipal

authorities can provide information on

how to dispose of the worn-out product.

The product is recyclable, subject to

extended producer responsibility and

is collected separately.

Kompernass Handels GmbH

warranty

Dear Customer,

This appliance has a 3-year warranty valid from the

date of purchase. If this product has any faults, you,

the buyer, have certain statutory rights. Your statu-

tory rights are not restricted in any way by the

warranty described below.

Warranty conditions

The warranty period starts on the date of purchase.

Please keep your receipt in a safe place. This will

be required as proof of purchase.

If any material or manufacturing fault occurs within

three years of the date of purchase of the product,

we will either repair or replace the product for you

or refund the purchase price (at our discretion).

This warranty service requires that you present the

defective appliance and the proof of purchase

(receipt) within the three-year warranty period,

along with a brief written description of the fault

and of when it occurred.

If the defect is covered by the warranty, your

product will either be repaired or replaced by us.

The repair or replacement of a product does not

signify the beginning of a new warranty period.

Warranty period and statutory claims for

defects

The warranty period is not prolonged by repairs

eﬀected under the warranty. This also applies to

replaced and repaired components. Any damage

and defects present at the time of purchase must be

reported immediately after unpacking. Repairs

carried out after expiry of the warranty period shall

be subject to a fee.

Scope of the warranty

This appliance has been manufactured in accord-

ance with strict quality guidelines and inspected

meticulously prior to delivery.

The warranty covers material faults or production

faults. The warranty does not extend to product

parts subject to normal wear and tear or to fragile

parts which could be considered as consumable

parts such as switches or parts made of glass.

The warranty does not apply if the product has been

damaged, improperly used or improperly main-

tained. The directions in the operating instructions

for the product regarding proper use of the product

are to be strictly followed. Uses and actions that

are discouraged in the operating instructions or

which are warned against must be avoided.

PMTS 180 A1 GB│IE │ 13 ■

This product is intended solely for private use and

not for commercial purposes. The warranty shall be

deemed void in cases of misuse or improper

handling, use of force and modiﬁcations / repairs

which have not been carried out by one of our

authorised Service centres.

The warranty period does not apply to

■ Normal reduction of the battery capacity

overtime

■ Commercial use of the product

■ Damage to or alteration of the product by the

customer

■ Non-compliance with safety and maintenance

instructions, operating errors

■ Damage caused by natural hazards

Warranty claim procedure

To ensure quick processing of your case, please

observe the following instructions:

■ Please have the till receipt and the item number

(IAN)373210_2104 available as proof of

purchase.

■ You will ﬁnd the item number on the type plate

on the product, an engraving on the product,

on the front page of the operating instructions

(below left) or on the sticker on the rear or

bottom of the product.

■ If functional or other defects occur, please

contact the service department listed either by

telephone or by e-mail.

■ You can return a defective product to us free of

charge to the service address that will be

provided to you. Ensure that you enclose the

proof of purchase (till receipt) and information

about what the defect is and when it occurred.

You can download these instructions

along with many other manuals,

product videos and installation

software at www.lidl-service.com.

This QR code will take you directly to the Lidl

service page (www.lidl-service.com) where you

can open your operating instructions by entering

the item number (IAN) 373210_2104.

NOTE

► For Parkside tools, please send us only the

defective item without the accessories (e.g.

battery, storage case, assembly tools, etc.).

WARNING!

►Have the power tool repaired by the

service centre or a qualiﬁed electrician and

only using genuine replacement parts. This

ensures that the safety of the tool is main-

tained.

►Always ensure that the power plug or the

mains cable is replaced only by the manu-

facturer of the appliance or its customer

service. This ensures that the safety of the

tool is maintained.

Service

Service Great Britain

Tel.: 0800 404 7657

E-Mail: [email protected]

Service Ireland

Tel.: 1890 930 034

(0,08 EUR/Min., (peak))

(0,06 EUR/Min., (oﬀ peak))

E-Mail: [email protected]

IAN 373210_2104

Importer

Please note that the following address is not the

service address. Please use the service address

provided in the operating instructions.

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

PMTS 180 A1

■ 14 │ GB│IE

Translation of the original Conformity Declaration

We, KOMPERNASS HANDELS GMBH, documents oﬃcer: Mr. Semi Uguzlu, BURGSTR. 21,

44867 BOCHUM, Germany, hereby declare that this product complies with the following standards,

normative documents and EC directives:

Machinery Directive

(2006/42/EC)

Electromagnetic Compatibility

(2014/30/EU)

RoHS Directive

(2011/65/EU)*

* The manufacturer bears the full responsibility for compliance with this conformity declaration. The object of the

declaration described above complies with the requirements of the Directive 2011/65/EU of the European Parliament

and Council of 8 June 2011 on the limitations of use of certain dangerous substances in electrical and electronic

appliances.

Applied harmonised standards

EN 62841-1:2015

EN 62841-3-10:2015/A11:2017

EN ISO 12100:2010

EN 55014-1:2017/A11:2020

EN 55014-2:2015

EN 61000-3-2:2014

EN IEC 61000-3-2:2019

EN 61000-3-3:2013

EN 61000-3-3:2013/A1:2019

EN IEC 63000:2018

Type/appliance designation: Metal Cutting Chop Saw PMTS 180 A1

Year of manufacture: 07–2021

Serial number: IAN 373210_2104

Bochum, 22.07.2021

Semi Uguzlu

- Quality Manager -

The right to eﬀect technical changes in the context of further development is reserved.

PMTS 180 A1 DE│AT│CH │ 15 ■

Inhaltsverzeichnis

Einleitung .............................................................16

Bestimmungsgemäßer Gebrauch .......................................................16

Ausstattung ........................................................................16

Lieferumfang .......................................................................16

Technische Daten ...................................................................17

Allgemeine Sicherheitshinweise für Elektrowerkzeuge .......................17

1. Arbeitsplatzsicherheit ..............................................................18

2. Elektrische Sicherheit ..............................................................18

3. Sicherheit von Personen ............................................................18

4. Verwendung und Behandlung desElektrowerkzeugs .....................................19

5. Service .........................................................................19

Sicherheitshinweise für Trennschleifmaschinen ..............................19

1) Sicherheitshinweise für Trennschleifmaschinen ...........................................19

2) Rückschlag und entsprechende Sicherheitshinweise ......................................21

Weitere Sicherheitshinweise für Trennschleifer ..............................21

Originalzubehör/-zusatzgeräte ........................................................24

Vor der Inbetriebnahme ................................................24

Gerät aufstellen ....................................................................24

Transportsicherung entfernen/einsetzen ..................................................24

Inbetriebnahme .......................................................24

Ein-/ausschalten ....................................................................24

Schnitttiefe einstellen ................................................................24

Trennscheibe wechseln ...............................................................24

Werkstück einspannen ...............................................................25

Reinigung und Wartung .................................................25

Entsorgung ...........................................................26

Garantie der Kompernaß Handels GmbH ..................................26

Service ............................................................... 27

Importeur ............................................................27

Original-Konformitätserklärung ..........................................28

PMTS 180 A1

■ 16 │ DE│AT│CH

METALL-TRENNSCHLEIFER

PMTS 180 A1

Einleitung

Wir beglückwünschen Sie zum Kauf Ihres neuen

Gerätes. Sie haben sich damit für ein hochwertiges

Produkt entschieden. Die Bedienungsanleitung ist

Teil dieses Produkts. Sie enthält wichtige Hinweise

für Sicherheit, Gebrauch und Entsorgung. Machen

Sie sich vor der Benutzung des Produkts mit allen

Bedien- und Sicherheitshinweisen vertraut. Benut-

zen Sie das Produkt nur wie beschrieben und für

die angegebenen Einsatzbereiche. Händigen Sie

alle Unterlagen bei Weitergabe des Produkts an

Dritte mit aus.

Bestimmungsgemäßer Gebrauch

Der Trennschleifer ist dazu bestimmt, als Standgerät

mithilfe von Trennscheiben Längsschnitte mit gera-

dem Schnittverlauf und Gehrungswinkel bis 45° in

Stahl, NE-Metallen, Guss- und Eisenproﬁlen ohne

Verwendung von Wasser auszuführen.

Jede andere Verwendung oder Veränderung der

Maschine gilt als nicht bestimmungsgemäß und

birgt erhebliche Unfallgefahren.

Verwenden Sie das Gerät nicht zu gewerblichen

Zwecken.

Ausstattung

EIN-/AUS-Schalter

Spannﬂansch (innen)

Spindelarretierung

Trennscheibe

Schnellverstellung

Schraubstock

Bohrungen

Schnittwinkelverstellung

Transportsicherung

Schnitttiefenverstellung

Motoreinheit

Handgriﬀ

Abbildung A

Pendelschutzhaube

Schutzabdeckung

14a Integrierter Tragegriﬀ

Befestigungsschrauben

Abbildung B

Spannﬂansch (außen)

Unterlegscheibe

Befestigungsmutter

Abbildung C

Innensechskantschlüssel (groß)

Innensechskantschlüssel (klein)

Lieferumfang

1 Metall-Trennschleifer PMTS 180 A1

1 Trennscheibe Ø 180 mm (vormontiert)

2 Innensechskantschlüssel

1 Bedienungsanleitung

PMTS 180 A1 DE│AT│CH │ 17 ■

Technische Daten

Bemessungsspannung 230 V ∼, 50 Hz

(Wechselstrom)

Bemessungsaufnahme 1280 W

Bemessungsleerlaufdrehzahl n0 7700 min-1

Trennscheibenaufnahme Ø 22,23 mm

Gewindemaß M8

Maximale Geschwindigkeit

der Trennscheibe 8500 min-1

Arbeitsgeschwindigkeit

der Trennscheibe max. 80 m/s

Trennscheibendurchmesser Ø 180 mm

Trennscheibendicke 1,6 mm

Neigungsschnitte 0°–45°

max. Schnitttiefe

50mm

50 mm bei 0 °

Gehrungswinkel

Schutzklasse II /

(Doppelisolierung)

Geräuschemissionswert

Messwert für Geräusch ermittelt entsprechend

EN62841. Der A-bewertete Geräuschpegel des

Elektrowerkzeugs beträgt typischerweise:

Schalldruckpegel LPA = 93 dB (A)

Unsicherheit KPA = 3 dB

Schallleistungspegel LWA = 106 dB (A)

Unsicherheit KWA = 3 dB

Gehörschutz tragen!

WARNUNG!

► Die Schwingungs- und Geräuschemissionen

können entsprechend der Art und Weise in

der das Elektrowerkzeug verwendet wird, ins-

besondere, welche Art von Werkstück bearbei-

tet wird, abweichen und können in manchen

Fällen über dem in diesen Anweisungen an-

gegebenen Werten liegen. Die Schwingungs-

belastung könnte unterschätzt werden, wenn

das Elektrowerkzeug regelmäßig in solcher

Weise verwendet wird. Versuchen Sie, die

Belastung durch Vibrationen so gering wie

möglich zu halten. Beispielhafte Maßnahmen

zur Verringerung der Vibrationsbelastung

sind das Tragen von Handschuhen beim Ge-

brauch des Werkzeugs und die Begrenzung

der Arbeitszeit. Dabei sind alle Anteile des

Betriebszyklus zu berücksichtigen (beispiel-

weise Zeiten, in denen das Elektrowerkzeug

abgeschaltet ist, und solche, in denen es zwar

eingeschaltet ist, aber ohne Belastung läuft).

Allgemeine

Sicherheitshinweise für

Elektrowerkzeuge

WARNUNG!

►Lesen Sie alle Sicherheitshinweise, Anwei-

sungen, Bebilderungen und technischen

Daten, mit denen dieses Elektrowerkzeug

versehen ist. Versäumnisse bei der Einhal-

tung der nachfolgenden Anweisungen kön-

nen elektrischen Schlag, Brand und/oder

schwere Verletzungen verursachen.

Bewahren Sie alle Sicherheitshinweise und

Anweisungen für die Zukunft auf.

Der in den Sicherheitshinweisen verwendete Begriﬀ

„Elektrowerkzeug“ bezieht sich auf netzbetriebene

Elektrowerkzeuge (mit Netzleitung) und auf akku-

betriebene Elektrowerkzeuge (ohne Netzleitung).

La page charge ...

Parkside PMTS Manuel utilisateur

Parkside PMTS Manuel utilisateur

dans d''autres langues

Documents connexes