KEESON RF408A Mode d'emploi

Taper
Mode d'emploi
Issue DepartmentBedding Division
Date
2022-11-18
System Instruction
Author
Instruction of RF408A
Edition
1.1
Page 1 of 4
1 / 4
Instruction of RF408A
Figure 1 button ofremote
Issue DepartmentBedding Division
Date
2022-11-18
System Instruction
Author
Instruction of RF408A
Edition
1.1
Page 2 of 4
2 / 4
Item
1.1 PLAY /PAUSE button 1
Press the PLAY /PAUSE button to play or pause the audio device.
1.2 Sync button 2
Press Sync button to active the model of the audio device, between Sync and Async model.
1.3 Timer 3
Press the Timer button to set the active time of the audio device.
1.4 Volume + 4
Press the volume + button to increace the volume of the audio device.
1.5 Volume - 5
Press the volume - button to decreace the volume of the audio device.
1.6 Power 6
Press the power button to open and shut the light.
1.7 Morning 7
Press the morning button to set the light into morning model.
1.8 Evening 8
Press the morning button to set the light into Evening model.
Issue DepartmentBedding Division
Date
2022-11-18
System Instruction
Author
Instruction of RF408A
Edition
1.1
Page 3 of 4
3 / 4
intensityswitches among 0-1-2-3
1.9 Brightness + 9
Press the volume + button to increace the brightness of the light.
1.10 Brightness - 10
Press the volume - button to decreace the brightness of the light.
.
1.11 Timer 11
Press the Timer button to set the active time of the light.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two cond
itions: (1) this device may not cause harmful interference, and (2) this device must accept any int
erference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could v
oid the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital de
vice, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protec
tion against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructi
ons, may cause harmful interference to radio communications. However, there is no guarantee th
at interference will not occur in a particular installation. If this equipment does cause harmful int
erference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Issue DepartmentBedding Division
Date
2022-11-18
System Instruction
Author
Instruction of RF408A
Edition
1.1
Page 4 of 4
4 / 4
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
ISED Statement
- English: This device complies with Industry Canada licenseexempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interferen
ce, and (2) This device must accept any interference, including interference that may cause u
ndesired operation of the device. The digital apparatus complies with Canadian CAN ICES
3 (B)/NMB3(B).
French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradi
oélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le fonctionnement.
This radio transmitter (ISED certification number: 22406-RF408A) has been approved by
Industry Canada to operate with the antenna types listed with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the maximum gain
indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (ISED certification number: 22406-RF408A) a été approuvé par
Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un
gain admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

KEESON RF408A Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues