Canarm ALX105-UD Manuel utilisateur

Marque: Canarm

Modèle: ALX105-UD

Taper: Manuel utilisateur

ALX SERIES

SPUN ALUMINUM EXHAUSTER

OPERATION INSTRUCTIONS AND PARTS MANUAL

READ AND SAVE THESE INSTRUCTIONS

GENERAL SAFETY

1. All electrical work must be done in accordance with all applicable electrical codes by a

qualified electrician.

2. Prior to wiring ensure the power supply is locked in the OFF position and that the motor

nameplate voltage matches the supply voltage.

3. Do not install or operate this fan in an environment where combustible materials, gases or

fumes are present.

4. Caution: the fan contains rotating parts and electrical service. Appropriate safety

precautions should be taken during installation, operation and maintenance.

When servicing the fan motor may be hot, allow time for cooling down.

5. Before starting the unit, ensure the wheel rotates freely.

6. Check and tighten where necessary all nuts, bolts & set screws prior to fan start up (as

some may have loosened during shipment).

7. Please follow all applicable national, state/provincial and local codes, all of them will

supersede this manual.

8. Failure to follow the safety instructions in this manual may cause serious injury or

death due to electrical shock or high speed rotating parts.

The purpose of this manual is to aid in the proper installation and operation of the blowers. These instructions are intended to supplement good

general practices and are not intended to cover detailed instruction procedures.

IT IS THE RESPONSIBILITY OF THE PURCHASER TO ASSURE THAT THE INSTALLATION AND MAINTENANCE OF THIS EQUIPMENT IS

HANDLED BY QUALIFIED PERSONNEL.

Inspect all shipments carefully for damage. THE RECEIVER MUST NOTE ANY DAMAGE ON THE CARRIER’S BILL OF LADING AND FILE A

CLAIM IMMEDIATELY WITH THE FREIGHT COMPANY.

DO NOT LIFT THE UNIT BY THE HOOD OR MOTOR. PLEASE LIFT THE UNIT BY HORIZONTAL SUPPORTS.

DIMENSION & COMPONENT

ALX-M-06_27_22 Page 1 of 7

UPBLAST

MODELS DOWNBLAST

MODELS

NOTE: DUE TO MOTOR MANUFACTURERS VARIANCES IN DESIGN,

PLEASE SEE PAGE 5 FOR MOTOR DIMENSIONAL GUIDELINES.

DOWNBLAST UPBLAST

Downblast Direct

Drive Shown

Note: Belt drive units are weighted without motor & drives.

Upblast Belt

Drive Shown

Motor plate detail varies

on different sizes

Model A B C D E F G Ø

Wheel

Diameter

Roof

Opening

Net

Weight

(lbs)

ALX105-DD 18.00 25.00 19.00 2.50 1.50 3.50 0.38 10.50 15.00 33

ALX120-DD 19.00 25.00 19.00 3.50 1.50 3.50 0.38 12.25 15.00 35

ALX135-DD/DB 22.25 / 25.25 31.25 21.00 3.13 2.00 3.75 0.44 13.50 17.00 51 / 59

ALX150-DD/DB 23.13 / 26.13 31.25 21.00 3.75 2.00 3.75 0.44 15.00 17.00 56 / 65

ALX165-DD/DB 27.13 / 31.13 36.25 24.75 5.00 2.00 4.00 0.44 16.50 20.75 100 / 106

ALX180-DD/DB 27.75 / 31.75 36.25 28.00 5.50 2.00 4.00 0.44 18.25 20.75 104 / 110

ALX210-DB 36.25 43.75 33.13 5.25 2.50 4.00 0.44 21.25 29.00 176

ALX245-DB 37.00 43.75 33.13 5.88 2.50 4.00 0.44 24.50 29.00 181

Dimensions (inches)

Model A B C D E F G Ø Wheel

Diameter

Roof

Opening

Net

Weight

(lbs)

ALX105-UD 17.63 25.00 19.00 13.00 1.50 3.50 0.38 10.50 15.00 35

ALX120-UD 18.63 25.00 19.00 13.00 1.50 3.50 0.38 12.25 15.00 37

ALX135-UD/UB 22.25 / 25.25 32.13 21.00 17.13 1.50 3.75 0.44 13.50 17.00 53 / 62

ALX150-UD/UB 23.13 / 26.13 32.13 21.00 17.13 1.50 3.75 0.44 15.00 17.00 58 / 67

ALX165-UD/UB 27.13 / 31.13 37.50 24.75 21.13 2.00 4.00 0.44 16.50 20.75 100 /108

ALX180-UD/UB 27.75 / 31.75 37.50 28.00 21.13 2.00 4.00 0.44 18.25 20.75 108 / 116

ALX210-UB 36.25 43.75 33.13 25.50 2.50 4.00 0.44 21.25 29.00 178

ALX245-UB 37.00 43.75 33.13 25.50 2.50 4.00 0.44 24.50 29.00 183

Dimensions (inches)

ALX SERIES

SPUN ALUMINUM EXHAUSTERS

ALX-M-06_27_22 Page 2 of 7

1. A qualified electrician in accordance with all local and National Electrical Codes should do all wiring.

2. Ensure power supply is disconnected and locked out prior to making electrical connections.

3. Wire the motor according to the wiring diagram on motor label or on the sticker inside the motor wrap. All motors should be wired to

the same rotation as indicated on the sticker on the top plate.

4. Leave enough slack in the wiring to allow for motor movement when adjusting the belt tension.

5. Excess wire must be restrained in order to prevent it from entering the pulley, shaft or wheel rotating area.

6. Disconnect switches are recommended and should be located near the fan in order to, swiftly cut off power in case of an emergency

and maintain complete control of the power source.

Some single phase direct drive motor’s running RPM can be adjustable with a variable speed control (please contact factory for more

information). The speed control knob starts at off position, then high to low adjust range. At high speed, the speed control would allow the

motor running at its maximum RPM. Dial the knob to the low side would let the speed control regulate the voltage on the motor to reduce

the RPM.

A minimum speed adjustment is needed to limit the motor RPM range. Follow this procedure to set the minimum speed.

1. Motor must be in servicing status to allow the minimum speed setting. Motor would not slow down unless proper load is applied.

Motor RPM would be changed under different system (static pressure).

2. Turn the main control knob to the lowest speed position.

3. Locate and adjust the minimum speed setting, it can be found on the control box itself.

4. Motor RPM range would be from full RPM to the RPM just set.

The lowest minimum voltage that may be applied to the motors is 65VAC. Running at lower voltage can cause premature failure

to the motor.

For 3 phase motors, a variable frequency drive (VFD) is required to adjust motor speed.

VARIABLE SPEED CONTROL – SINGLE PHASE

VARIABLE FREQUENCY DRIVE – THREE PHASE

INSTALLATION

RECOMMENDED

ROOF OPENING

WIRED TO POWER

BY OTHERS

ROOF

DECK

OPTIONAL DISCONNECT CAN

BE MOUNTED INSIDE THE

HOUSING OR OUTSIDE

MINIMUM 12”

RECOMMENDED

ROOF OPENING

ROOF

DECK

MINIMUM 12”

WIRE OPTION 2:

WIRE THROUGH

THE VENT TUBE

WIRE OPTION 1:

THROUGH CONDUIT

GENERAL CLEAN AIR APPLICATION (UPBLAST) GENERAL CLEAN AIR APPLICATION, DOWNBLAST

Note: ALX105 to ALX120 has only wiring option 1, ALX135 to ALX180 has both

wiring options 1 and 2, ALX210 and larger has only wiring option 2.

STANDARD WIRING INSTRUCTIONS

1. Install roof curb, caulk and flash to ensure the water tightness.

2. Rotate the blower wheel by hand. Wheel should not be rubbing against the housing inlet. If rubbing occurs, loosen the set screws on

the wheel hub and shift the wheel to obtain clearance. Then re-tighten all set screws.

3. Complete all subsequent duct connections.

4. Secure the fan to the curb cap. Do not lift the unit by the hood or motor. Lift the unit by horizontal supports on direct drive or by motor

mounting plate for belt drive unit.

5. Use at least 8 proper fasteners to connect the blower base to the roof curb.

6. Verify if the power supply is compatible with the equipment.

7. Make sure the power line is shut down before wiring the motor to power line.

8. Remove top cap, connect power line to the motor/disconnect switch as indicated.

9. For all up blast units, the electrical supply enters the motor compartment through the vent tube.

10. Ensure all fasteners and set screws are tightened.

11. Place the top cap back on the hood.

12. Caulk and flash the fan base including the fan base corners and roof curb to ensure good water tightness.

MESSAGE DISPLAYED...

Spd- followed by the instantaneous speed in rpm

dE- followed by S + demand in %

E1- No communications

E2- Under Voltage

Power is connected to the motor and control module through the

junction box and wiring harness provided.

Note: For 115VAC operation the blue jumper provided (taped to wire

harness) must be inserted into motor power

connector. See diagram.

Caution: Operating the motor at 208-230VAC with the jumper will cause significant damage to the motor.

AC Supply - 115/208-230VAC

EC motors are equipped with a control module that allows for accurate manual adjustment

of motor speed. Motor speed range is from 300 to 1800rpm or maximum rpm for that

model.

The control module features a 4 digit LED display that indicates % demand of full speed

and motor speed in rpm. The display also indicates an error code message for minor

diagnostics if required.

Motor speed can be changed by adjusting the speed control pot located on the control

module. A small screwdriver can be used to make the speed adjustment.

ALX SERIES

SPUN ALUMINUM EXHAUSTERS

ALX-M-06_27_22 Page 3 of 7

EC (Electronically Controlled) MOTOR SPEED CONTROL

Note: EC motors have a soft start

feature. When the power is turned on

the control module gathers information

from the motor then begins the start up

process. After a few seconds the motor

will start to turn and reach full set speed

in 10-15 seconds.

Remote Speed Control Option (please

contact factory for further inform ation)

If your unit

contains the

ECsmart

Motor

please follow

these wiring

diagrams:

RECOMMENDED

ROOF OPENING

WELDED DUCT

BY OTHERS GREASE

COLLECTOR

(OPTIONAL)

MINIMUM 20”

FROM ROOF TOP

VENTED CURB

DISCONNECT MOUNTED

OUTSIDE OF THE HOUSING,

WIRED THROUGH THE VENT

TUBE BY OTHERS

WIRED TO POWER

BY OTHERS

ROOF

DECK

WALL

WALL MOUNT BRACKET

(OPTIONAL)

RECOMMENDED

ROOF OPENING

WELDED DUCT

BY OTHERS

DISCONNECT MOUNTED

OUTSIDE OF THE HOUSING,

WIRED THROUGH THE VENT TUBE

All up-blast models are UL/cUL listed, they are capable to meet UL705 Supplement SC for Commercial Kitchen application:

• The National Fire Protection Association (NFPA) publication NFPA 96 is the primary source for this application. Also consult local

authorities for all other applicable codes and guidelines before installation.

• Exhaust fans used in kitchen ventilation applications must have external wiring. (Wiring must not be installed in the airstream).

• Installation must include a means for inspecting, cleaning and servicing the exhaust fan. (Curb hinge, grease collector and outdoor

disconnect switches are available for purchase as accessories)

• No dampers can be used in the system.

RESTAURANT EXHAUST APPLICATION

1. Lock out all power sources.

2. Inspect all fasteners and set screws and tighten as required.

3. Inspect belt alignment and tension where applicable.

4. Confirm power source voltage and motor voltage are the same and that the motor is wired correctly.

5. Rotate the wheel to ensure that neither the fan blade nor the belts come into contact with the housing.

6. Inspect the fan and the ductwork to ensure they are free of debris.

7. Check to ensure that all guards and accessories are securely mounted.

PRE-START INSPECTION

Turn the fan on and inspect for the following:

1. Direction of rotation.

2. Improper motor amperage.

3. Excessive vibration.

4. Unusual noise.

5. Improper belt tension or alignment (only applicable on belt-drive unit).

If a problem is discovered shut off the fan and refer to the section on troubleshooting to discover the cause of the problem. The fan should

be inspected after 30 minutes, 8 hours & 24 hours of operation to ensure all fasteners are tight and belts are properly tensioned and aligned.

START UP

UPBLAST UL762 RESTAURANT EXHAUST INSTALLATION UPBLAST WALL MOUNTED RESTAURANT EXHAUST INSTALLATION

ALX SERIES

SPUN ALUMINUM EXHAUSTERS

ALX-M-06_27_22 Page 4 of 7

ALX SERIES

SPUN ALUMINUM EXHAUSTERS

ALX-M-06_27_22 Page 5 of 7

FAN TROUBLESHOOTING

Disconnect and secure to the OFF position all electrical power to the fan prior to inspection or servicing. Failure to comply with this safety

precaution could result in serious injury or death.

1. Ventilator should be checked at least once a year. For critical or severe applications a routine check every two to three months is

suggested.

2. Guard to be kept free of debris. Easily installed/removed using the integrated twist lock tabs. Gently twist the guard tab so that it slips

under the support arm to lock in place. Guard is easily removeable for fan servicing and cleaning. No tools are required.

3. When moving or installing a belt, don’t force the belt over the sheave. Loosen the motor mount so that the belt can be easily slipped

over the sheave.

4. The belt, on belt driven units, should be removed and carefully checked for cracks, ply separation or irregular wear. A small

irregularity in the contact surface of the belt will result in noisy operation. If any of these defects are apparent the belt should

be replaced. At the same time check the sheaves for chips, dents or rough surfaces that could damage the belt.

5. The correct belt tension is important. Too tight a belt will result in excess bearing pressure, which can cause premature bearing failure

and may cause the motor to overload. Too loose a belt will result in slippage, which will burn out belts. Proper belt deflection should

be 1/64” (half way between sheave centers) for each inch of belt span when a force of approximately 5 lbs. is applied.

6. The belt alignment should be checked to be sure that the belt is running perpendicular to the rotating shafts. Motor and drive shafts

must be parallel.

7. A periodic inspection of all fasteners should be carried out to ensure they have not loosened due to vibration. Particular attention

should be paid to fasteners attaching the wheel to the shaft and those attaching the shaft to the bearing.

MAINTENANCE

WARNING

MAkE SURE THE UNIT IS NOT CAPABLE OF OPERATION

DURING REPARATION.

PROBLEM POSSIBLE ISSUE SOLUTION

Wheel rubbing inlet Adjust wheel, loosen set screw(s) and move the wheel, acquiring

clearance between inlet and wheel, then re-tighten set screw(s)

Wheel unbalance Check wheels for debris or dirt build up and clean when necessary

Object in rotation area or housing Remove object

Motor compartment loose Re-tighten the fasteners

Malfunction of electrical supply Check supply voltage, fuse and switch

Malfunction of motor Check wiring and overload protector

Motor overload/overheat Wrong wheel rotation Re-wire the motor to change direction of rotation

Damper Malfunction Check opening side of back draft damper, check operation status of

controlled damper

Wrong wheel rotation Re-wire the motor to change direction of rotation

Improper Duct System Check obstruction of duct in the duct or dirty filter

Discharge Blockage Check discharge and remove any debris

Excessive noise/vibration

Fan does not operate

Reduced airflow

ALX SERIES

SPUN ALUMINUM EXHAUSTERS

ALX-M-06_27_22 Page 6 of 7

FAN MOTOR DIMENSIONAL

GUIDELINES

MOTOR MOUNTING

FAN FRAME SIZES MAX "A" MAX

"B"

MAX

"C"

MAX

"D"

RESILIENT

BASE

MAX SHEAVE

DIA.

ALX135UB/DB 48, 56 8.5 6.5 10.5 7 NO 5.5

ALX150UB/DB 48, 56 8.5 6.5 10.5 7 NO 5.5

ALX165UB/DB 48, 56, 143, 145 8.5 8 13 7 NO 5.5

ALX180UB/DB 48, 56, 143, 145 8.5 8 13 7 NO 5.5

ALX210UB/DB 56, 143, 145, 182, 184 11.5 11 12 8 YES 8

ALX245UB/DB 56, 143, 145, 182, 184 11.5 11 12 8 YES 8

FAN MAX

"A"

MAX

"B"

MAX

"C"

C-FACE

ONLY

ALX105/120UD 14 14 8.5 56 FRAME

ALX105/120DD 10 10 7.5 56 FRAME

ALX135/150UD 15 15 15 56 FRAME

ALX135/150DD 15 15 15 56 FRAME

ALX165UD 16 16 15.5 56 FRAME

ALX165DD 16 16 15.5 56 FRAME

1 HP ADAPTER PLATE

48 OR 56 FRAME

BOTH SIDES 48, 56, 143-145 FRAME 48, 56, 143-145, 182-184 FRAME

ALX135/ALX150 ALX165/ALX180 ALX210/ALX245

ALX SERIES SPUN ALUMINUM UPBLAST

EXHAUSTERS - EXPLODED VIEW

ITEM # DESCRIPTION QTY

1 TOP CAP 1

2 MOTOR WRAP 1

3 MOTOR SUPPORT PLATE 1

4 VIBRATION ELIMINATOR 4

5 TOP PLATE 1

6 UPBLAST APRON 1

7 VENT 1

8 VERTICAL BRACKET 4

9 INLET BAFFLE 4

10 DRAIN 4

11 MOTOR SUPPORT RAIL 2

12 HORIZONTAL BRACKET 4

13 BASE 1

14 BLOWER WHEEL 1

ALX SERIES SPUN ALUMINUM DOWNBLAST

EXHAUSTERS - EXPLODED VIEW

ITEM # DESCRIPTION QTY

1 MOTOR WRAP 1

2 BEARING 2

3 MOTOR SUPPORT PLATE 1

4 VERTICAL BRACKET 4

5 TOP CAP 1

6 VENT TUBE 1

7 DOWNBLAST APRON 1

8 MOTOR SUPPORT RAIL 2

9 VIBRATION ELIMINATOR 4

10 SHAFT 1

11 TOP PLATE 1

12 INLET BAFFLE 1

13 BASE 1

14 BLOWER WHEEL 1

NOTE: General

models are

shown above.

Actual unit might

vary according

to size.

ALX-M-06_27_22 Page 7 of 7

Canarm Ltd. - Corporate Head Office 2157 Parkedale Avenue, PO Box 367 Brockville, Ontario Canada K6V 5V6

Tel: (613) 342-5424; Fax: (613) 342-8437 www.canarm.com [email protected]

WARRANTY

CANARM Ltd. warrants every new fan to be free of defects in material and workmanship to the extent that, within a period of one year

from the date of purchase CANARM Ltd. shall either repair or replace at CANARM’s option, any unit or part thereof, returned freight

prepaid, and found to be defective.

This warranty does not include any labour or transportation costs incidental to the removal and reinstallation of the unit at the user’s

premises.

Components repaired or replaced are warranted through the remainder of the original warranty period only; it is null and void in case of

alteration, accident, abuse, neglect, and operation not in accordance with instructions.

NOTICE: No warranty claims will be honored by CANARM Ltd. unless prior authorization is obtained.

SÉRIES ALX

ÉVACUATEUR EN ALUMINIUM REPOUSSÉ

MODE D’OPÉRATION ET LISTE DES PIÈCES

LIRE ET GARDER CES INSTRUCTIONS

PRECAUTIONS GÉNÉRALES

1. Tout le travail électrique doit être fait par un électricien qualifié selon les normes et les

codes applicables.

2. Avant de débuter le câblage assurez-vous que la ligne n’est pas sous tension et que le

voltage utilisé est identique èa celui mentionné sur la plaque d’identification du moteur.

3. N’opérer pas ce ventilateur dans un environnement oû les matériaux combustibles, les

gaz,ou la fumée sont présents.

4. Mise en garde : Ce ventilateur inclus des pièces rotatives et électriques. Des mesures de

sécurité appropriées doivent être prises durant l’installation, l’opération et l’entretien.

Lorsque vous procédez à l’entretien, le moteur peut être chaud. Allouer un temps de

refroidissement.

5. Avant de démarrer l’unité, assurez-vous que la roue tourne librement.

6. Vérifiez et serrez oû nécessaire, tous les écrous, les boulons et les vis avant de démarrer le

ventilateur (certains ont peut-être été desserrés pendant l'expédition).

7. Suivre tous les codes nationaux, provinciaux et locaux concernant l’usage de cet

appareil car ils supplantent de manuel

8. Ne pas suivre les instructions de ce manuel peut causer de sérieuses blessures ou

la mort due à un choque électrique ou aux pièces en rotation.

Le but de ce livret et de vous faciliter dans l’installation et l’opération de souffleurs. Ces instructions doivent complémenter des bonnes pratiques

générales et ne sont pas conçus pour couvrir les procédures détaillées.

IL EST LA RESPONSABILITÉ DE L’ACHETEUR DE S’ASSURER QUE L’INSTALLATION ET L’ENTRETIEN DE CET ÉQUIPEMENT SOIENT

FAITS PAR UN PERSONNE QUALIFIÉE.

Inspecter la marchandise lors de la réception pour s’assurer qu’il n’y a aucun dommage. SI VOUS CONSTATEZ DES DOMMAGES, VOUS DEVEZ

LES NOTER SUR LE CONNAISSEMENT DU TRANSPORTEUR ET FAIRE UNE RÉCLAMATION AU TRANSPORTEUR IMMÉDIATEMENT.

NE SOULEVEZ PAS L’ÉQUIPEMENT PAR LE CAPOT OU LE MOTEUR. SOULEVEZ L’UNITÉ PAR LES SUPPORTS HORIZONTAUX.

DIMENSIONS ET PIÈCES

ALX-M-FR-06_27_22 Page 1 de 7

MODÈLE À

DÉBIT VERS

LE HAUT

MODÈLE À

DÉBIT VERS

LE BAS

MODÈLE À DÉBIT

VERS LE HAUT

MODÈLE À DÉBIT

VERS LE BAS

Modèle A B C D E F G Ø

Diamètre

de la

oue

Ouverture

Toit

Poids

Net

(