CAT 502-3700 Mode d'emploi

501–5289-00

Owner's Manual

RP12000 E Portable Generators

2

Important Safety Information

Most accidents that involve product operation, maintenance and repair are caused by failure to observe

basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous

situations before an accident occurs. A person must be alert to potential hazards, including human factors

that can affect safety. This person should also have the necessary training, skills and tools to perform

these functions properly.

Safety precautions and warnings are provided in this manual and on the product. If these hazard

warnings are not heeded, bodily injury or death could occur to you or to other persons. The hazards are

identified by the “Safety Alert Symbol” and followed by a “Signal Word” such as “DANGER”,

“WARNING” or “CAUTION”.

Caterpillar cannot anticipate every possible circumstance that might involve a potential hazard. The

warnings in this publication and on the product are, therefore, not all inclusive. You must not use this

product in any manner different from that considered by this manual without first satisfying yourself that

you have considered all safety rules and precautions applicable to the operation of the product in the

location of use, including site-specific rules and precautions applicable to the worksite. If a tool,

procedure, work method or operating technique that is not specifically recommended by Caterpillar is

used, you must satisfy yourself that it is safe for you and for others. You should also ensure that you are

authorized to perform this work, and that the product will not be damaged or become unsafe by the

operation, lubrication, maintenance or repair procedures that you intend to use.

The information, specifications, and illustrations in this publication are on the basis of information that was

available at the time that the publication was written. The specifications, torques, pressures,

measurements, adjustments, illustrations, and other items can change at any time. These changes can

affect the service that is given to the product. Obtain the complete and most current information before

you start any job.

In the United States, the maintenance, replacement, or repair of the emission control devices and

systems

may be performed by any repair establishment or individual of the owner's choosing.

This manual contains safety, operation, and maintenance information. This manual should be stored near

the product. Read, study and keep it with the literature and product information.

Consumer Arbitration Clause

The Limited Warranty included in this User Guide contains important legal terms including, but not limited

to, a Consumer Arbitration Clause calling for mandatory individual arbitration and waiving the ability to

bring a case as a class action. Please review this carefully.

California Proposition 65 Warning

3

Table of Contents

Consumer Arbitration Clause ........................................................................................................... 2

California Proposition 65 Warning ..................................................................................................... 2

SAFETY MESSAGES ................................................................................................................................... 5

Additional Messages ......................................................................................................................... 6

Special Requirements ....................................................................................................................... 6

ASSEMBLY ............................................................................................................................................... 7

Unpackaging ...................................................................................................................................... 7

Feet Assembly ................................................................................................................................... 7

Wheel Assembly ............................................................................................................................... 7

Lifting Eye Assembly ........................................................................................................................ 8

Handle Assembly .............................................................................................................................. 8

Battery Connection ........................................................................................................................... 8

Oil ....................................................................................................................................................... 8

COMPONENT IDENTIFICATION ................................................................................................................. 9

Engine Type & Serial Number ........................................................................................................ 10

CONTROLS ............................................................................................................................................. 11

Display ............................................................................................................................................. 11

Generator Switch ............................................................................................................................ 11

Choke ............................................................................................................................................... 11

Fuel Switch ...................................................................................................................................... 11

Engine Idle Control Switch ............................................................................................................. 11

AC Circuit Breaker .......................................................................................................................... 12

240 VAC Circuit Breaker ................................................................................................................ 12

Low Oil Level Shutdown ................................................................................................................. 12

GENERATOR OPERATION ....................................................................................................................... 12

Optimal Generator Operating Conditions ...................................................................................... 12

Connection to Household Power Supply ....................................................................................... 12

Generator Grounding ...................................................................................................................... 12

AC Usage ........................................................................................................................................ 13

High Altitude Kits ............................................................................................................................. 13

BEFORE STARTING ENGINE .................................................................................................................... 13

Engine Oil ........................................................................................................................................ 13

Fuel .................................................................................................................................................. 13

Walk-Around Inspection ................................................................................................................. 13

STARTING THE ENGINE .......................................................................................................................... 14

4

Electric Start .................................................................................................................................... 14

STOPPING THE ENGINE .......................................................................................................................... 14

MAINTENANCE ...................................................................................................................................... 14

Air Filter – Check ............................................................................................................................. 15

Cylinder Head - Clean .................................................................................................................... 15

Engine Oil Level – Check ............................................................................................................... 15

Engine Oil and Oil Filter – Change ................................................................................................... 16

Engine Valve Lash – Inspect/Adjust .............................................................................................. 16

Fuel Line – Replace ........................................................................................................................ 16

Fuel Tank Cap and Strainer – Clean ............................................................................................. 16

Generator - Inspect ......................................................................................................................... 16

Spark Arrestor - Inspect/Clean/Replace........................................................................................ 16

Spark Plug – Inspect/Adjust/Replace ............................................................................................ 17

Walk-Around Inspection ................................................................................................................. 17

STORAGE ............................................................................................................................................... 18

Storage for 1 to 3 months ............................................................................................................... 18

Storage for more than 3 months .................................................................................................... 18

TROUBLESHOOTING .............................................................................................................................. 19

SPECIFICATIONS ..................................................................................................................................... 20

COMBINED EXHAUST AND EVAPORATIVE EMISSIONS CONTROLS WARRANTY STATEMENT..................... 21

Your Warranty Rights and Obligations .......................................................................................... 21

Manufacturer’s Warranty Coverage .............................................................................................. 21

Owner’s Warranty Responsibilities ................................................................................................ 21

Defects Warranty Requirements: .................................................................................................. 21

WARRANTY............................................................................................................................................ 23

CONSUMER ARBITRATION CLAUSE: MANDATORY BINDING INDIVIDUAL ARBITRATION

INSTEAD OF COURT; CLASS ACTION WAIVER ...................................................................... 23

5

SAFETY MESSAGES

There may be several specific safety messages

on

your generator. Please become familiar with

all safety

messages.

Ensure that all of the safety messages are legible.

Clean the safety messages or replace the safety

messages if the words cannot be read or if the

illustrations are not visible. Use a cloth, water, and

soap to clean the safety messages. Do not use

solvents, gasoline, or other harsh chemicals.

Solvents, gasoline, or harsh chemicals could

loosen

the adhesive that secures the safety

messages.

Replace any safety message that is damaged or

missing. If a safety message is attached to a part

of

the generator that is replaced, install a new

safety

message on the replacement part.

Read the Manual

Do not operate or work on this generator unless

you have read and understand the instructions

and warnings in the Owner’s Manual. Failure to

follow the instructions or heed the

warnings could

result in injury or death. Proper care is your

responsibility.

Hot Surface

Hot parts or hot components can cause burns or

personal injury. Do not allow hot parts or

components to contact your skin. Use protective

clothing or protective equipment to protect your

skin.

Operation of this equipment may create sparks

that can start fires around dry vegetation. A spark

arrestor may be required. The operator should

contact local fire agencies for laws or regulations

relating to fire prevention requirements.

Carbon Monoxide

Operating a generator indoors can kill you in

minutes. Generator exhaust contains carbon

monoxide. Carbon monoxide is a poison that

you cannot see or smell. Never operate a

generator inside a home or garage, even if

doors and windows are open. Only operate a

generator outdoors and away from windows,

doors, and vents. If anyone experiences

dizziness, headaches, nausea, or tiredness get

to fresh air immediately and seek medical

attention.

Electrocution

Shock/Electrocution Hazard: Do not

operate this

equipment or work on this equipment

unless you

have read and understand the

instructions and

warnings in the Owner’s Manual. Failure to

follow the

instructions or heed the warnings will

result in

serious injury or death.

DANGER

PELIGRO

Utiliser un générateur à

l’intérieur

PEUT VOUS

TUER

EN

QUELQUES MINUTES. Les gaz

d’échappement du générateur

contiennent du monoxyde de

carbone. C’est un gaz toxique

invisible et inodore.

 NE JAMAIS utiliser à l’intérieur

d’une maison ou d’un garage,

MÊME SI les portes et les

fenêtres sont ouvertes.

 Utiliser UNIQUEMENT à

l’EXTÉRIEUR et loin des

fenêtres, portes et ventilations.

Si usa un

generador en

interiores,

MORIRA

EN

POCOS

MINUTOS. El escape del

generador contiene monóxido

de carbono. Es un veneno que

no tiene olor ni se puede ver.

 NUNCA lo use dentro de una

casa o garaje. AUN si las

puertas y vantanas están

abiertas.

 Sólo úselo en EXTERIORES

y lejos de ventanas, puertas y

ductos de ventilación.

6

California Health and Safety Code 119080

Electrical backfeed into a utility’s distribution system

can cause property damage, severe injury, or death.

Do not connect generator to a building’s electrical

system until after the building’s main switch has been

used to isolate the building from the utility power

system. For permanent installations, connection shall

only be by means of a double throw switch as to isolate

the building from utility power system. Consult a

qualified technician for proper use and installation.

Comply with all applicable laws and electrical codes.

Additional Messages

Do not operate in wet

conditions

No smoking, no exposed

flames, no sparks.

Maintain a minimum distance

of 5 feet (1.5 meters) from

other objects.

Ensure that the unit is

properly grounded.

Eye protection must be worn

at all times.

This way up. Always keep

upright.

Recyclable – Follow local

recycling & reclaiming

procedures.

Never dispose of battery.

Take to designated waste

reclamation site.

Danger: Explosive Gases.

Danger: Battery Acid –

Corrosive and poisonous.

Special Requirements

Electrical equipment, including lines and plug

connections should be covered and protected

from moisture.

In any generator set installation, the frame of the

generator must be connected to an earth

ground. A ground terminal is provided.

The RP12000 E has a permanent neutral

conductor between the stator winding and the

frame.

For 120VAC, use extension cords rated for 125V

at 20A or greater. For 240VAC, use extension

cords rated for 250V at 30A or greater. Use the

shortest extension cord that meets these

requirements.

•

Wear a hard hat, protective glasses, and

other

protective equipment, as required.

•

When work is performed around an engine

that is

operating, wear protective devices for

ears in order

to help prevent damage to

hearing.

•

Do not wear loose clothing or jewelry that can

snag

on controls or on other parts of the

engine.

•

Ensure that all protective guards and all

covers are

secured in place on the engine.

•

Never put maintenance fluids into glass

containers. Glass containers can break.

•

Use all cleaning solutions with care.

The circuit breakers should match the generator

specifications. If the circuit breakers require

replacement, they must be replaced with a

circuit breaker of the same rating and

performance characteristics.

7

ASSEMBLY

NOTE: Only assemble unit with the included

hardware to avoid the risk of personal and

property damage.

Unpackaging

1. Remove both 8 mm bolts (1) from the

pallet and frame.

2. Remove both wood blocks (2) from

below the engine and alternator.

Feet Assembly

1. Set the frame of the unit on blocks to

provide sufficient clearance to install the

feet and wheels.

2. Align the foot (4) with the mounting hole

in the foot bracket (1).

3. Install and hand tighten one 8 mm nut

(2) onto the foot.

4. Tighten the nut securely.

5. Align the mounting holes of the foot

bracket (1) with the mounting holes in

the frame.

6. Insert one 8 mm bolt (3) through each

set of mounting holes and hand tighten.

7. Repeat steps 2 – 6 for the other foot.

8. Tighten all eight bolts securely.

Wheel Assembly

1. Insert long end of axle (5) into the

mounting bracket on the frame and run

through to insert into the other mounting

bracket on opposite side of frame.

2. Place the wheel stop (4) onto the long

end of the axle.

3. Place one wheel (1) onto the axle (5)

with the bolt design facing out.

4. Install one washer (3) onto the axle.

5. Install one 12 mm locking nut (2) onto

the axle and tighten securely.

6. Repeat steps 3 – 5 for the other wheel.

7. Remove the blocking.

1

4

3

2

5

3

4

2

1

2

1

8

Lifting Eye Assembly

1. Align the mounting holes of the lifting

eye (3) with the mouting holes in the

frame.

2. Place one washer (2) on each 10 mm

bolt (1) and insert through each

mounting hole.

3. Install and hand tighten one 10 mm nut

(4) on each bolt.

4. Tighten both nuts to 26 ± 2 lb ft

(35 ± 3Nm).

Handle Assembly

1. Install the foam grip (3) onto the handle

(4).

2. Insert one plug (1) into each end of the

handle (4).

3. Align the mounting holes of the handle

(4) to the mounting holes of the frame.

4. Insert one 8 mm bolt (5) through each

mounting hole.

5. Install and hand tighten one 8 mm nut

(2) on each bolt.

6. Tighten the nuts securely.

Battery Connection

The generator is packaged with a valve

regulated and maintenance free lead acid

battery. The generator is packaged with the

battery mounted in the battery holder. To

connect the battery:

1. The unit ships with the positive battery

cable (1) already connected.

2. Attach the cable with the black cap (2)

to the negative battery terminal.

NOTE: Replace battery only with the same part

number. Use of a non-conforming battery can

create a fire hazard.

Oil

Follow the Engine Oil Level-Check procedure to

add the proper amount of oil for the unit as

described in the Specifications chart.

2

1

4

3

2

1

5

4

2

3

1

9

COMPONENT IDENTIFICATION

1) Fuel Cap

2) Fuel Gauge

3) Lifting Eye

4) Oil Gauge / Oil Fill*

5) Spark Plug*

6) Battery

7) Starter

8) Oil Drain Valve

9) Oil Drain

10) Handle Assembly

11) Cover Panel

12) Air Filter Assembly

13) Air Filter

14) Muffler

15) Fuel Tank Vent Pipe

16) Engine

17) Oil Filter

18) CARB Canister (If equipped)

19) Spark Arrestor

20) Alternator

21) Engine Access Door

22) Fuel Valve

23) Panel Light

24) Choke Knob

25) Generator Switch

26) Idle Control Switch

27) Receptacle – DC 12V 8.3A

28) Display

29) Trickle Charger Port

30) Circuit Breaker

31) Receptacle – 120/240 VAC 50A

32) Receptacle – 120/240 VAC 30A

33) Receptacle – 120 VAC 30A

34) Receptacle – 120 VAC double

*behind engine access door

4, 5

1

2

3

9

10

11

12, 13

6

7

8

15

16

17

14

19

20

18

5

21

22

23

24

28

27

26

25

30

34

33

31

32

29

10

Engine Type & Serial Number

Cat

®

portable generators are identified with model numbers, serial numbers, and with performance

specification numbers. The model number and performance specifications are located on the ratings

plate (1). The serial number is located on the serial number plate (2).

1

2

1

2

11

CONTROLS

Display

This generator is equipped with a display that

can show the Voltage, frequency, total

accumulated hours of operation, and current

hours. Use toggle switch (1) to change the

readout of the display to the desired setting.

Generator Switch

Turn the generator switch to the start position

“ ” and hold until the engine starts (no more

than 5 seconds). Releasing the switch

automatically returns it to the on “I” position. To

turn off the generator, turn the generator switch

to the off “0” position.

NOTE: Turn the generator switch to the off “0”

position when not in use to avoid battery drain.

Choke

The choke is used to provide more fuel when

starting a cold engine. If the engine is cold, pull

the choke knob out before starting the engine.

Once the engine is warm, slowly push the choke

knob in.

Fuel Switch

The fuel switch controls the flow of the fuel from

the fuel tank to the carburetor.

Turn the fuel

switch to the on “I” position before starting the

engine. Turn the fuel switch to the off "O"

position after stopping the engine.

Engine Idle Control Switch

This generator is equipped with an engine idle

control switch. When in the on position “I” the

engine will reduce speed when power is not

required to conserve fuel, and reduce wear and

noise.

When power for a connected device is required

the speed will automatically increase to rated

speed.

Note: If loads requiring intermittent power, or

multiple large loads are connected, turn the idle

control switch off “O” to avoid possible engine

stall. To avoid extended warm-up time, keep the

idle control off until normal operating

temperatures have been reached.

12

AC Circuit Breaker

The generator comes equipped with circuit

breakers that protect the unit and the load from

short circuit or overload conditions. If the circuit

breaker opens, determine why the circuit breaker

tripped before closing the circuit breaker.

240 VAC Circuit Breaker

The 240V receptacles come with an additional

circuit breaker that will isolate these outlets on

the panel. This breaker must be in the “On”

position for the unit to provide power.

Low Oil Level Shutdown

The generator is equipped with a low oil level

shutdown that is designed to protect the engine

from damage caused by an insufficient amount

of oil in the crankcase. When the oil level in the

crankcase falls below the safe operating limit,

the low oil level shutdown will automatically

shut off the engine.

GENERATOR OPERATION

Optimal Generator Operating

Conditions

•

Temperature: 23

o

F to 104

o

F

(-5

o

C to 40

o

C)

•

Humidity below 95%

•

Height above sea level: < 3280 feet

(1,000 m). If the height of the operating

area is over 1,000 m high, output power

will be reduced.

Connection to Household Power

Supply

This generator must be installed in accordance

with all applicable local laws and electrical

codes. The generator must be isolated from the

utility and the connection must be verified by a

qualified electrician.

Generator Grounding

The National Electrical Code requires generators

to be grounded to an approved earth ground.

Correct grounding for the generator is necessary

for optimum engine performance and reduces

the risk of electric shock. Use the ground

terminal (1) to properly ground the generator.

Before using the ground terminal, consult

a

qualified electrician, electrical inspector, or local

authority having jurisdiction for local codes or

ordinances that apply for the intended use of the

generator.

1

13

AC Usage

Do NOT overload the generator. Exceeding the

rated power of the generator can damage the

generator and the electrical devices connected

to it.

Motor-driven devices require a large starting

current. Make sure that the total power

requirement of these types of loads does not

exceed the rated power of the generator.

When the generator is used to power multiple

loads or electric appliances, start by connecting

the appliance with the highest starting power

requirements, followed by the second highest

and ending with the lowest.

High Altitude Kits

At higher altitudes, the standard air-fuel mixture

is too rich and will cause decreased

performance and increased fuel consumption. A

rich mixture will also foul the spark plug and

make starting difficult. Operation at higher

altitudes for extended periods of time may

increase emissions.

Proper operation can be ensured by installing an

altitude kit when required. High altitude kits

should be installed by a qualified technician.

Contact an authorized service provider if the

portable generator will be operated at altitudes

greater than 3000 feet (0.9 km) above sea level.

Note: At elevations greater than 8000 feet

above sea level, the engine may experience

decreased performance even with the high

altitude kit installed.

BEFORE STARTING ENGINE

Engine Oil

Check the oil level before each use. Refer to the

Engine Oil Level - Check procedure in this

manual.

Fuel

1. Check the fuel level gauge (1).

2. If the fuel level is low, remove fuel cap

(2).

3. Check the strainer. If the strainer is

dirty, clean the strainer. Refer to Fuel

Tank Cap and Strainer – Clean for

instructions.

4. Add fuel. The use of a fuel stabilizer is

highly recommended as the unit may

sit for long periods of time before

needed.

5. Install the fuel cap after fueling.

To avoid personal injury always use caution

when you are adding fuel:

• Fuel the generator in a well-ventilated

area.

• Always stop the engine before fueling.

• Allow the engine to cool before fueling.

• Do not smoke while you are fueling the

generator.

• Do not fuel the generator near open

flames or sparks.

• Do not fill the fuel tank above the full line

(3).

• Avoid repeated or prolonged contact with

skin.

• Avoid prolonged breathing of fuel vapor.

To avoid damaging the generator:

• Use unleaded gasoline with an octane

rating greater than or equal to 90.

• Do not mix oil with the gasoline.

• Do not use gasoline with greater than

10% ethanol content.

• Do not use old gasoline.

• Avoid getting dirt or water into the fuel

tank.

Walk-Around Inspection

Perform the Walk-Around Inspection before

each use as described later in this manual.

1

2

3

4

14

STARTING THE ENGINE

Electric Start

1. Isolate the generator from the utility.

2. Unplug any electrical devices from the

receptacles.

3. Turn the fuel switch to the on “I”

position.

4. Turn the AC circuit breakers to the off

“0” position.

5. If the engine is cold, pull out the choke

knob.

6. Turn the generator switch to the start

position “ ” and hold it there until the

engine starts.

NOTE: Do not hold the generator switch in the

start position

“ ”

for more than 5 seconds.

Holding the generator switch in the start position

“ ”

for more than 5 seconds will damage the

starter. If the engine fails to start, wait 10

seconds before trying again.

7. After starting the engine, immediately

release the generator switch so the

switch can automatically return to the

on “I” position.

8. After the engine has warmed, push the

choke knob in.

9. Turn the AC circuit breaker to the on "I"

position.

STOPPING THE ENGINE

1. Disconnect the generator / unplug all

electrical devices.

2. Turn the AC circuit breaker to the off “0”

position.

3. Turn the generator switch to the off “0”

position.

4. Turn the fuel switch to the off “0”

position.

NOTE: To stop the engine in an emergency, turn

the generator switch to the off “0” position.

NOTE: Turn the generator switch to the off “0”

position when not in use to avoid battery drain.

MAINTENANCE

Ensure that all safety information, warnings, and

instructions are read and understood before any

maintenance procedures are performed.

Use service hours or calendar time, WHICH

EVER OCCURS FIRST, to determine the

correct maintenance intervals.

Stop the engine before servicing. Put the engine

in horizontal position and remove the spark plug

cap to prevent the engine from starting. Do not

operate the engine in an unventilated room or

other enclosed area.

When Required:

Fuel Tank Cap and Strainer – Clean

Every Use:

Engine Oil Level – Check

Walk-Around Inspection

First 20 Service Hours or 1 Month:

Engine Oil and Oil Filter– Change

Every Month:

Generator – Inspect

Every 50 Service Hours or 3 Months:

Air Filter – Check

Spark Arrester – Inspect/Clean/Replace

Every 100 Service Hours or 6 Months:

Engine Oil and Oil Filter – Change

Spark Plug – Inspect/Adjust/Replace

Every 300 Service Hours or 1 Year:

Cylinder Head – Clean

Engine Valve Lash – Check

Every 2 Years:

Fuel Line – Replace

15

Air Filter – Check

A dirty air filter will restrict air flow into the

carburetor, will cause poor fuel economy, and

may damage the engine. To keep the generator

in good operating condition, service the air filter

regularly. Service more frequently when

operating the generator in extremely dusty areas.

Note: Never operate the generator without the

air filter in place. Operating the generator without

the air filter in place will result in rapid engine

wear.

Remove the fan cover panel (5) by removing the

screws (6) and lifting out. Unscrew and remove

the air filter lock (1) and cover case (2).

Remove

the clip (3) and air filter (4). Make sure both the

paper and foam elements of the air filter (4) are

clean and not damaged. If the foam element is

dirty, wash it. If the paper element is dirty, knock

the dirt off. If either element is damaged, replace

the air filter.

Use a nonflammable solvent or a mixture of

household detergent and warm water to wash

the foam element. Rinse the filter thoroughly to

remove all of the cleaning solution. Never let the

foam element contact engine oil.

Note: Do not wring out the filter. Wringing out the

filter may damage the filter.

Use a damp rag to wipe dirt from the case and

cover. Install the filter into the housing. Place the

clip over the filter. Place the cover case over the

filter and clip. Reinstall the lock and screw in the

cover panel.

Cylinder Head - Clean

Only qualified service personnel should perform

this maintenance procedure. Contact your local

service center to schedule this maintenance.

Engine Oil Level – Check

Always check the engine oil with the generator

on a level surface and with the engine stopped.

1.

Open engine access door. Remove the

oil level gauge (1) and wipe clean.

2.

Check the oil level by re-inserting the oil

level gauge.

3.

If the oil level is low (2), remove the oil

filler cap (4) and add the recommended

engine oil, using the articulated funnel

supplied, until the oil level reaches the

upper mark (3) on the oil level gauge.

Use the chart below to determine which

viscosity oil to use.

4.

After adding oil, install and tighten the

oil filler cap (4) and oil level gauge (1),

and close the engine access door.

Note: Non-detergent and 2-stroke engine oils will

damage the engine and

must not be used.

Recommended Lubricant Viscosities for

Ambient Temperature

Oil Viscosities

o

C

o

F

Min Max Min Max

SAE 0W-40 -40 40 -40 104

SAE 5W-40 -30 50 -22 122

SAE 10W-30 -18 40 0 104

SAE 15W-40 -10 50 14 122

1

2

3

4

5

6

3

2

1

4

16

Engine Oil and Oil Filter – Change

1. Operate the engine until it reaches

normal operating temperature. Stop the

engine and use a suitable container to

collect the used oil.

2. Remove the oil filler cap and open the

oil drain valve (1). Remove the oil

drain hose from the cap (2) to drain the

oil.

3. Use an oil filter socket to remove the oil

filter (3). Discard the used oil filter

according to local regulations.

4. Apply clean oil to the seal of the new oil

filter. Install the new oil filter. Tighten the

oil filter to 10 ± 1.5 lb ft (14 ± 2Nm).

5. Close the oil drain valve (1) and

reattach the oil drain to the cap (2).

6. Refill the oil, using the articulated

funnel supplied, and check the oil level.

Refer to Engine Oil Level – Check.

7. Install and tighten the oil filler cap.

8. Dispose of the used oil properly.

9. Start the engine for a brief period and

check for leaks.

10. Stop the engine and check the oil level.

Refer to Engine Oil Level – Check.

Engine Valve Lash – Inspect/Adjust

Only qualified service personnel should perform

this maintenance procedure. Contact your local

service center to schedule this maintenance.

Fuel Line – Replace

Only qualified service personnel should perform

this maintenance procedure. Contact your local

service center to schedule this maintenance.

Fuel Tank Cap and Strainer – Clean

Wipe off the fuel cap (1) and surrounding area

before removing the fuel cap. Wiping off the fuel

cap and surrounding area before removing the

fuel cap helps to reduce the amount of

contaminants allowed into the fuel system.

If there is a build-up of debris in the fuel strainer

(2), remove the strainer and rinse out the

strainer. Allow the strainer to dry before

installing the strainer.

Generator - Inspect

Once a month start the engine and run the

engine until it reaches normal operating

temperature (about 20 minutes). Plug in a

corded device and turn on the device to ensure

that the generator is providing power. Once you

have verified that the generator is providing

power, turn off the device and unplug it. Then

turn the generator off.

Spark Arrestor -

Inspect/Clean/Replace

This unit has a spark arrestor fitted to the

exhaust outlet of the muffler. The spark arrestor

should be cleaned with a soft wire brush after

every 50 hours or 3 months of use. The spark

arrestor should be replaced after every 100

hours of operation or if it becomes damaged.

Hot Surface

Hot parts or hot components can cause burns or

personal injury. Do not allow hot parts or

components to contact your skin. Use protective

clothing or protective equipment to protect your

skin.

1

2

1

2

3

17

DO NOT perform this maintenance procedure

until the muffler has cooled.

Remove screws (2). Remove spark arrestor (1)

Check the spark arrestor. Carefully clean the

spark arrestor with a soft wire brush. If the spark

arrestor is damaged, replace the spark arrestor.

To install the spark arrestor, align the mounting

holes in the spark arrestor with the mounting

holes on the muffler. Insert screws (2) and

tighten securely.

Spark Plug – Inspect/Adjust/Replace

Refer to the Specifications section of this

manual to determine the proper spark plug part

number and spark plug gap for your product.

1. DO NOT perform this maintenance

procedure with the engine running.

2. Turn the generator switch to the off “O”

position.

3. Open the engine access door.

4. Remove the spark plug cap (3).

5. Use the plug wrench (1) or a spark plug

socket to remove the spark plug (2).

6. Visually check the spark plug to see if

it is damaged. If the insulator is

cracked, replace the spark plug. If the

electrode is damaged, replace the spark

plug.

7. Measure the plug gap (4) with a feeler

gauge. Adjust the gap as necessary by

carefully bending the side electrode.

Refer to Specifications for the correct

gap for your product.

8. Check the spark plug washer to ensure

proper working condition. If the washer

is damaged, replace the washer.

9. Install spark plug and tighten to 16 ± 2

lb ft (22 ± 2 Nm). DO NOT overtighten

as this may damage the engine.

10. Re-attach the spark plug cap.

11. Repeat steps 4-10 for the other spark

plug on the other side of the engine.

Walk-Around Inspection

Before starting the engine perform a visual

inspection of the unit. Look for:

• Proper oil level

• Proper fuel level

• Good quality fuel

• Fluid leaks

• Loose clamps

• Loose bolts

• Cracked fuel line

• Loose or frayed wiring

• Built up debris

In addition, make sure that:

• The ground terminal is properly

connected

• The circuit breakers are in OFF “ 0 ”

position

1

2

1

2

3

4

18

STORAGE

When a generator is in storage, air may

condense and moisture may appear on the

windings. In order to minimize condensation,

always store the generator in a dry area. Cover

the generator with a protective cover that

extends to the ground. The cover should remain

loose around the generator in order to allow

proper ventilation.

Storage for 1 to 3 months

Remove any dirt, rust, grease, and oil from the

generator. DO NOT use a pressure washer to

clean the generator. Inspect the exterior. Make

any necessary repairs.

Add fuel stabilizer to the fuel tank to prevent the

gasoline from going bad. Start and run the

engine for 10 minutes to ensure that the fuel

stabilizer has been pulled in to the carburetor.

Shut off the engine and allow the engine to cool.

Turn the fuel valve to the off “O“ position.

Move the generator to the storage place.

Attach the trickle charger to the port in the

control panel and to standard AC power to keep

the generator battery fully powered for easy start

after storage. Disconnect the battery charger

once the battery is fully charged (indicated by a

green light on the charger).

Cover the generator.

Storage for more than 3 months

Remove any dirt, rust, grease, and oil from the

generator. DO NOT use a pressure washer to

clean the generator. Inspect the exterior. Make

any necessary repairs.

Gasoline is extremely flammable and is

explosive under certain conditions. Drain the fuel

in a well-ventilated area with the engine stopped

and cool. Never smoke or allow flames or sparks

in the area during

this procedure.

Drain the fuel from the fuel tank into a suitable

container using a manual siphon pump. DO

NOT save the fuel for future use in the

generator. Turn the fuel valve to the on “I“

position. Start and run the engine until the

engine stops, to allow the fuel to drain from the

fuel lines and engine system. Turn the fuel valve

to the off “O” position. Apply a small amount of

oil to the threads on the fuel tank filler neck and

install the cap.

Change the engine oil. Refer to Engine Oil and

Oil Filter – Change.

Remove both spark plugs and pour a small

amount of oil into both cylinders. Install the

spark plug but do not install the spark plug cap.

Move the generator to the storage place.

Attach the trickle charger to the port in the

control panel and to standard AC power to keep

the generator battery fully powered for easy start

after storage. Disconnect the battery charger

once the battery is fully charged (indicated by a

green light on the charger)

Cover the generator.

19

TROUBLESHOOTING

Issue:

Possible Cause:

Solution:

Check:

Engine Will

Not Start

Generator switch in the off “ 0 ”

position

Turn the generator switch to the

correct position.

Start the engine.

Choke knob in the wrong position

Place the choke knob in the

correct position.

No fuel Fill the fuel tank.

Bad or contaminated fuel Check the fuel.

Not enough oil in the engine

Check the oil level. If low, add

the recommended oil.

Dirty air filter Clean the air filter.

No fuel at the carburetor

Make sure the fuel switch is in

the

on

"

I

" position.

Engine flooded Wait 5 minutes.

No spark Replace the spark plug.

No battery power

Check the battery. If the battery

is providing less than 12.7 volts,

charge the battery, if providing

less than 12.4 volts, replace the

battery.

If the engine still will not start: Take the unit to an authorized service provider.

Engine Runs

Rough (no

load)

Dirty air filter

Stop the engine and check the

air filter. Clean if needed.

Start the engine /

check if it runs rough.

Choke knob in the wrong position

Place the choke knob in the

correct

position.

If the engine still runs rough: Take the unit to an authorized service provider.

Engine Shuts

Down

Out of fuel

Check the fuel. Fill the tank if

necessary.

Start the engine /

check if it shuts down.

Not enough oil in the engine

Check the oil level. If low, add

the recommended oil.

Dirty air filter Clean the air filter.

Generator overloaded Unplug some of the devices.

If the engine still shuts down: Take the unit to an authorized service provider.

Engine Runs

Rough (with

load)

Dirty air filter

Stop the engine and check the

air filter. Clean if needed.

Start the engine /

check if it runs rough.

Generator overloaded Unplug some of the devices.

Defective device plugged in Unplug defective device.

If the engine still runs rough: Take the unit to an authorized service provider.

Engine Runs,

But Generator

Does Not

Provide

Power

Circuit breaker is open Close the circuit breaker.

Start the engine /

check for power.

Bad connection

Stop the engine and check the

connections.

Defective power cord Replace the cord.

Defective device plugged in Unplug defective device.

If there is still no power: Take the unit to an authorized service provider.

20

SPECIFICATIONS

Engine Type

Two Cylinder, 4-Stroke, Forced Air Cooling

Displacement (cc)

67

0

Ignition System Transistorized Magneto

Spark Plug Gap

.028

-

.032 inch

es

(

0.7

–

0.8

mm)

Fuel Volume

13 U.S. gallons (50L)

Fuel Consumption

(g/(kW·h)

≤ 374

100% load continuous

7.5

running

time (hr)

50% load continuous

11.7

running

time (hr)

Oil Capacity

1.5 quart (1.6L)

Charging Voltage (VDC)

12

-

60

Charging Current (A)

0

-

100

Rated Frequency (Hz)

60

Rated Voltage (V)

120/240

Rated Output Power (kW)

US

12

Canada

11

Surge Output Power (kW)

15

Phase

Single

Total Harmonic Distortion

< 5%

La page charge ...

CAT 502-3700 Mode d'emploi

Ce manuel convient également à

CAT 502-3700 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents