Welch Allyn 9600 Plus Manuel utilisateur

9600 Plus Calibration Tester

of the product described in this publication, the purchaser of the product

is permitted to copy this publication, for internal distribution only, from

the media provided by Welch Allyn. No other use, reproduction, or

distribution of the publication, or any part of it, is permitted without

written permission from Welch Allyn.

Welch Allyn assumes no responsibility for any injury to anyone, or for any

illegal or improper use of the product, that may result from failure to use

this product in accordance with the instructions, cautions, warnings, or

statement of intended use published in this manual.

Welch Allyn is a registered trademark of Welch Allyn. Braun ThermoScan

is a registered trademarks of Braun Corporation.

Printed in Mexico

DIR 80020333 Ver A

Revised: 2017-06

i

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Symbols and Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Unpacking the 9600 Plus Calibration Tester . . . . . . . . . . . . . 4

Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . 5

LCD Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power On Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front of the 9600 Plus Calibration Tester . . . . . . . . . . . . . . . 7

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

9600 Plus Calibration Tester Setup. . . . . . . . . . . . . . . . . . . 11

Changing the Calibration Set Point Temperature . . . . . . . . 11

Welch Allyn SureTemp and SureTemp Plus Thermometers 13

Braun ThermoScan Pro 4000 Model. . . . . . . . . . . . . . . . . . 15

Braun ThermoScan Pro 6000 model. . . . . . . . . . . . . . . . . . 18

Braun ThermoScan Pro 3000 Model. . . . . . . . . . . . . . . . . . 23

Troubleshooting inaccurate readings . . . . . . . . . . . . . . . . . 25

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Electromagnetic Compatibility . . . . . . . . . . . . . . . . . . . . . . 32

ii

Warranty and Service . . . . . . . . . . . . . . . . . . . . . . . . . 33

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Symboles et descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Mises en garde. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Déballage du testeur d’étalonnage 9600 Plus . . . . . . . . . . . 4

Commandes et indicateurs . . . . . . . . . . . . . . . . . . . . . . 5

Affichage ACL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Séquence de mise en marche . . . . . . . . . . . . . . . . . . . . . . . 7

Avant du testeur d’étalonnage 9600 Plus. . . . . . . . . . . . . . . 7

Fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installation du testeur d’étalonnage 9600 Plus. . . . . . . . . . 11

Modification de la température du point d'étalonnage. . . . 11

Thermomètres Welch Allyn SureTemp et SureTemp Plus . 13

Modèle Braun ThermoScan Pro 4000. . . . . . . . . . . . . . . . . 15

Modèle Braun ThermoScan Pro 6000. . . . . . . . . . . . . . . . . 19

Modèle Braun ThermoScan Pro 3000. . . . . . . . . . . . . . . . . 24

Résolution des problèmes de relevés incorrects . . . . . . . . 26

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Nettoyage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Dépannage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Spécifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Compatibilité électromagnétique . . . . . . . . . . . . . . . . . . . . 32

Directions for Use Contents iii

Garantie et entretien . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Garantie limitée. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Entretien . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Einführung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Symbole und Beschreibungen . . . . . . . . . . . . . . . . . . . . . . . 2

Vorsicht . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Auspacken des Kalibriertesters 9600 Plus . . . . . . . . . . . . . . 4

Bedienelemente und Anzeigen . . . . . . . . . . . . . . . . . . . 5

Flüssigkristallanzeige . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Einschaltreihenfolge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Vorderseite des Kalibriertesters 9600 Plus. . . . . . . . . . . . . . 7

Betrieb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Konfiguration des Kalibriertesters 9600 Plus . . . . . . . . . . . 11

Ändern der Kalibrier-Sollwerttemperatur. . . . . . . . . . . . . . . 11

Die Thermometer SureTemp und SureTemp Plus von

Welch Allyn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Das Modell ThermoScan Pro 4000 von Braun . . . . . . . . . . 15

Modell Braun ThermoScan Pro 6000 . . . . . . . . . . . . . . . . . 18

Das Modell ThermoScan Pro 3000 von Braun . . . . . . . . . . 23

Fehlerbehebung bei ungenauen Werten . . . . . . . . . . . . . . 25

Wartung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Reinigung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Fehlerbehebung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Technische Daten . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Elektromagnetische Verträglichkeit. . . . . . . . . . . . . . . . . . . 32

Gewährleistung und Service . . . . . . . . . . . . . . . . . . . . 33

Beschränkte Gewährleistung . . . . . . . . . . . . . . . . . . . . . . . 33

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

iv

1

Introduction

The 9600 Plus Calibration Tester verifies calibration of the

following thermometers:

• Welch Allyn SureTemp

®

models (678, 678 OEM, 679 and

986)

• Welch Allyn SureTemp

®

Plus models (690, 692 and 692

OEM)

• Braun ThermoScan

®

Pro 3000, Pro 4000, and Pro 6000

The 9600 Plus Calibration Tester provides a tightly regulated

temperature source that eliminates the setup, precision

calibration, and maintenance requirements of water baths and

other general purpose calibration equipment. The user takes

the “temperature” of the 9600 Plus Calibration Tester with the

knowledge and assurance that precise readings are obtained

because the unit is factory calibrated to National Institute of

Standards and Technology (NIST) or equivalent devices. User

adjustments are not required or recommended.

The “blackbody” of the 9600 Plus Calibration System acts as

a heat reservoir for the thermistor probe and as a heat

radiator for the infrared ear thermometers.

The unit contains solid-state circuitry for long-term stability

with minimal maintenance. Welch Allyn uses only precision

components in the construction of the 9600 Plus Calibration

Tester. To maintain traceability to NIST or equivalent, return

the 9600 Plus Calibration Tester to the factory for annual

calibration.

2 Chapter 1 Introduction Welch Allyn 9600 Plus Calibration Tester

Symbols and Descriptions

Double Insulation.

Direct Current.

Handle with Care.

Attention! Caution; Consult Directions for Use for more

information.

Transport/Storage Temperature

Relative Humidity

Separate collection for electronic equipment

Recyclable

95%

15%

Directions for Use Chapter 1 Introduction 3

Cautions

A caution statement in this manual identifies a condition or

practice which, if not corrected or discontinued immediately,

could lead to equipment failure, equipment damage, or data loss.

Caution Do not immerse or soak the 9600 Plus

Calibration Tester in any type of fluid.

Caution Only trained Biomedical personnel should

operate the 9600 Plus Calibration Tester and conduct

calibration verification of thermometers.

Caution When not using the Thermistor or Ear Device

Ports, keep them covered with the Dust Cover.

Caution Store thermometers for testing in the same

room as the 9600 Plus Calibration Tester for

approximately 30 minutes prior to testing to allow the

thermometer to reach ambient room temperature.

Caution Do not clean the Thermistor or Ear Device

Ports. Doing so may damage the surface. Only a Welch

Allyn authorized Service Center should clean the Device

Ports.

4 Chapter 1 Introduction Welch Allyn 9600 Plus Calibration Tester

Unpacking the 9600 Plus Calibration Tester

Unpack the 9600 Plus Calibration Tester and inspect for missing

items. Retain the shipping materials to return the device to

Welch Allyn for recalibration.

The following items are enclosed:

• A 9600 Plus Calibration Tester

• A package containing a power supply and four mains plug

inserts

• The Directions for Use

• A Carrying Case

If any of these items are missing after opening, please contact

Welch Allyn Customer Service at the number provided on

page 34.

5

2

Controls and Indicators

LCD Display

Figure 1. LCD Display and Front Buttons

Calibration Set Point Temperature

There are three Calibration Set Point temperatures used to

test the calibration of the thermometer. The three

temperatures are 36° C (96.8° F), 38.5° C (101.3° F), and 41°

Current Cavity

Temperature

Units

Calibration Set

Point Temperature

Set Point

Mode

Celsius/Fahrenheit

Selection Button

Temperature

Selection

Button

6 Chapter 2 Controls and Indicators Welch Allyn 9600 Plus Calibration Tester

C (105.8° F). The LCD displays the current Calibration Set Point

Temperature in the upper left corner of the LCD.

Current Cavity Temperature

The current temperature of the 9600 Plus Calibration Tester is

indicated by the large numbers in the center of the display

(Figure 1).

As the device is transitioning to the current Calibration Set Point

Temperature, the actual temperature flashes on the display.

When the device reaches the Calibration Set Point Temperature,

the temperature in the center of the display stops flashing.

Temperature Units

The 9600 Plus Calibration Tester is capable of displaying the

temperature in degrees Fahrenheit or Celsius.

Set Point Mode

The LCD will display either a "D" (Default) or "L" (Last Used) in the

upper left hand corner (Figure 1). The 9600 Plus Calibration

Tester has two set point modes of operation. The Default mode

(from the factory) causes the 9600 Plus Calibration Tester to heat

up to the lowest set point (36.0

°

C / 96.8

°

F) upon startup. The Last

Used mode causes the 9600 Plus Calibration Tester to heat up to

the last temperature setting that was used.

To change the Set Point Mode, press and hold the C/F and Arrow

buttons below the LCD display simultaneously until a single audio

beep is heard. A “D” or an “L” will appear in the upper left corner

of the display for the new mode.

Directions for Use Chapter 2 Controls and Indicators 7

Power On Sequence

The 9600 Plus Calibration Tester receives power from a wall-

mount power pack that plugs into the back of the unit. There is

no ON/OFF switch. On power up, the 9600 Plus Calibration

Tester performs internal self-checks, displays an all-segments

test pattern, beeps and displays the device’s current

temperature. The 9600 Plus Calibration Tester immediately

applies heat, if needed, to reach the selected Calibration Set

Point Temperature.

Front of the 9600 Plus Calibration Tester

Temperature Selection Button

This button allows the user to select one of three set point

temperatures: 36.0

°

C (96.8

°

F), 38.5

°

C (101.3

°

F), or 41.0

°

C

(105.8

°

F).

To scroll from one set point to the next, press and hold the

Temperature Selection button until a beep is heard. The newly

selected set point appears in the upper left corner of the LCD

display. The device’s current temperature is displayed, will start

to flash, and continue flashing until the cavity reaches the

equilibrium at the new set point.

Celsius/Fahrenheit Selection Button

This button allows the user to select degrees Celsius or degrees

Fahrenheit. To change the temperature units, press and hold the

C/F button until a beep is heard. The temperatures will appear in

either “°C” or “°F”, see (Figure 1).

8 Chapter 2 Controls and Indicators Welch Allyn 9600 Plus Calibration Tester

Figure 2. Front of the 9600 Plus Calibration Tester

Caution Verify the thermometer being tested and the

9600 Plus are set to use the same temperature scale

before running a test. Reference the thermometers

directions for use to change its temperature scale

Thermistor

Device Port

Ear Device

Port

Dust Cover

Power Jack

Directions for Use Chapter 2 Controls and Indicators 9

Dust Cover

This black, plastic cover keeps dust from entering the Thermistor

and Ear Device Ports. To expose the Thermistor and Ear Device

Ports, rotate the Dust Cover counter clockwise. To cover the

ports, rotate the Dust Cover clockwise.

Thermistor and Ear Device Ports

The Ear Device Port is the larger of the two ports located under

the dust cover and is for the Braun ThermoScan Pro 3000 and

Pro 4000 ear thermometers (Figure 2).

The Thermistor Device Port is the smaller port located under the

dust cover and is for the SureTemp and SureTemp Plus

thermometers.

The surface texture inside the Ear Device Port is painted with a

special dull, black paint to enable Ear device readings. You can

only see its surface under bright light. The Thermistor Device

Port is not painted black. Keep both clean and dry.

The coating in the device ports of the unit is fragile, so please

follow the cleaning instructions carefully. Do not touch the

surface, and do not allow any foreign objects to be inserted into

the ports. Avoid spilling liquids onto the unit. If liquid or other

contaminants enter the unit, Welch Allyn can not assure proper

calibration and you must return the unit to Welch Allyn for

recalibration.

Caution When not using the Thermistor or Ear Device

Ports, keep them covered with the Dust Cover.

10 Chapter 2 Controls and Indicators Welch Allyn 9600 Plus Calibration Tester

11

3

Operation

9600 Plus Calibration Tester Setup

Place the 9600 Plus Calibration Tester on a level surface away

from sunlight, drafts, and other sources of heat or cold. The

9600 Plus Calibration Tester takes approximately 20 minutes

to heat to the lowest setting. When testing several

thermometers at all three temperatures, it is recommended

to test all probes at one Calibration Set Point Temperature

before proceeding to the next Calibration Set Point

Temperature. To further expedite testing start at the lowest

Calibration Set Point Temperature. The 9600 Plus Calibration

Tester does not have an internal fan, causing the cool down

time to be greater than the time it takes to heat up.

Changing the Calibration Set Point

Temperature

To scroll from one set point to the next, press and hold the

Temperature Selection button until a beep is heard. The

newly selected set point appears in the upper left corner of

the LCD display. The device’s current temperature is

displayed, starts to flash, and continues flashing until the

cavity reaches the equilibrium at the new set point.

12 Chapter 3 Operation Welch Allyn 9600 Plus Calibration Tester

Figure 3. Power Adapter and Mains Plug Inserts

For the setup:

1. Choose the proper mains plug insert and slide it over the two

prongs in the power converter (Figure 3).

2. Plug the power adapter into the 9600 Plus Calibration Tester

(Figure 2) and the opposite end into a wall outlet.

3. Observe the Set Point Mode in the upper left hand corner of

the LCD display (Figure 1). If the unit displays a “D”, it is in

Default Mode and will heat to the lowest Set Point

Temperature. If you do not want to conduct testing at this Set

Point Temperature, press and hold the Temperature Selection

button to select the desired setting. The temperature display

will flash before staying on continuously to indicate the 9600

Plus Calibration Tester has stabilized and is ready for use.

UKUS EUAUS

Two prongs in the

power adapter

Directions for Use Chapter 3 Operation 13

Welch Allyn SureTemp and SureTemp Plus

Thermometers

Figure 4. 9600 Plus Calibration Tester with the Welch Allyn SureTemp

Plus Thermometer

To begin calibration verification of the thermometers:

1. Remove the probe from the probe well and clean it with either

a 70% isopropyl alcohol solution, a 10% chlorine bleach

Caution Store thermometers for testing in the same

room as the 9600 Plus Calibration Tester for

approximately 30 minutes prior to testing to allow the

thermometer to reach ambient room temperature.

Note

Prior to testing visually inspect the probe for any physical

damage. Damaged probes must be replaced.

14 Chapter 3 Operation Welch Allyn 9600 Plus Calibration Tester

solution, or a non-staining disinfectant. Let the probe air dry.

Do not apply a probe cover.

2. Place the thermometer in Monitor Mode, refer to the

thermometer’s Operator's Manual.

3. Insert the probe into the Thermistor Device Port (Figure 4).

4. Wait for approximately one minute or until temperature on the

thermometer is stable for ten seconds. Compare the

thermometer's temperature reading to the 9600 Plus'

Calibration Set Point Temperature. If the temperatures are

within ±0.1° C (±0.2° F), the thermometer is within

calibration.

5. Test all available thermometers for calibration verification at

the current Calibration Set Point Temperature. Proceed to the

next Calibration Set Point Temperature, see "Changing the

Calibration Set Point Temperature" (page 11).

La page charge ...

Welch Allyn 9600 Plus Manuel utilisateur

Welch Allyn 9600 Plus Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents