Hitachi CR 18DGL Manuel utilisateur

Marque: Hitachi

Modèle: CR 18DGL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Model

Cordless Reciprocating Saw

Modèle

Scie alternative sans ﬁ l

Modelo

Sierra sable a batería

CR 18DGL

Designed for operating in USA & Canada only.

When this product is used in areas other than the USA & Canada,

we cannot guarantee the product quality and performance.

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.

Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce

mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent

l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool. This manual should be

stored in safe place.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y com-

prenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para

que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual

debe ser guardado en un lugar seguro.

TABLE DES MATIERES

Français

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

...... 19

SIGNIFICATION DES MOTS D’AVERTISSEMENT

....... 19

SÉCURITÉ ................................................................ 19

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX

CONCERNANT LES OUTILS ÉLECTRIQUES

.......19

REGLES DE SÉCURITÉ SPÉCIFIQUES ............... 21

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LA BATTERIE ET LE CHARGEUR

DE BATTERIE

................................................. 22

PRÉCAUTIONS RELATIVES A LA BATTERIE AU

LITHIUM ION ..................................................... 23

DESCRIPTION FONCTIONNELLE ........................... 25

NOM DES PARTIES ............................................... 25

SPECIFICATIONS .................................................. 26

Page

ASSEMBLAGE ET FONCTIONNEMENT ................. 27

UTILISATIONS ....................................................... 27

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE ............................................ 27

MÉTHODE DE RECHARGE .................................. 27

AVANT L’UTILISATION ........................................... 29

UTILISATION .......................................................... 31

ENTRETIEN ET INSPECTION .................................. 33

ACCESSOIRES ......................................................... 34

ACCESSOIRES STANDARD .................................. 34

ACCESSOIRES EN OPTION ................................ 34

LISTE DES PIECES .................................................. 53

CONTENTS

Page

ASSEMBLY AND OPERATION ................................. 10

APPLICATIONS ..................................................... 10

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................. 10

CHARGING METHOD ........................................... 10

PRIOR TO OPERATION ......................................... 12

OPERATION .......................................................... 13

MAINTENANCE AND INSPECTION ........................ 16

ACCESSORIES ......................................................... 17

STANDARD ACCESSORIES ................................. 17

OPTIONAL ACCESSORIES

.................................... 17

PARTS LIST .............................................................. 53

Page

IMPORTANT SAFETY INFORMATION .................. 3

MEANINGS OF SIGNAL WORDS ......................... 3

SAFETY ..................................................................... 3

GENERAL POWER TOOL SAFETY WARNINGS

...... 3

SPECIFIC SAFETY RULES .................................... 5

IMPORTANT SAFETY INSTRUCTIONS FOR

BATTERY AND BATTERY CHARGER ............ 6

CAUTION ON LITHIUM-ION BATTERY.................. 7

FUNCTIONAL DESCRIPTION .................................. 8

NAME OF PARTS .................................................. 8

SPECIFICATIONS ................................................. 9

English

ÍNDICE

Español

Página

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ................................................... 36

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN ............................................. 36

SEGURIDAD ............................................................. 36

ADVERTENCIAS DE SEGURIDAD GENERAL

DE LA HERRAMIENTA ELÉCTRICA .............. 36

NORMAS ESPECÍFICOS DE SEGURIDAD .......... 38

INSTRUCCIONES DE SEGURIDAD IMPORTANTES

PARA LA BATERÍA Y EL CARGADOR DE

BATERÍAS

...................................................... 39

ADVERTENCIA DE LA BATERÍA DE LITIO ............ 40

DESCRIPCIÓN FUNCIONAL ................................... 42

NOMENCLATURA ................................................. 42

ESPECIFICACIONES ............................................ 43

Página

MONTAJE Y OPERACIÓN ....................................... 44

APLICACIONES .................................................... 44

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA .............................................. 44

MÉTODO DE CARGA ............................................ 44

ANTES DE LA OPERACIÓN .................................. 46

OPERACIÓN ......................................................... 47

MANTENIMIENTO E INSPECCIÓN ......................... 50

ACCESORIOS .......................................................... 51

ACCESORIOS ESTÁNDAR ................................... 51

ACCESORIOS OPCIONALES ............................... 51

LISTA DE PIEZAS .................................................... 53

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before

operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety

rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,

and by observing appropriate safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which contain

the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identiﬁ ed by WARNINGS on the power tool

and in this Instruction Manual.

NEVER use this power tool in a manner that has not been speciﬁ cally recommended by HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or

may cause machine damage.

NOTE emphasizes essential information.

SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

ﬂ ammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord

for carrying, pulling or unplugging the

power tool.

Keep cord away from heat, oil, sharp edges

or moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use

an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and

use common sense when operating a power

tool.

English

Do not use a power tool while you are tired

or under the inﬂ uence of drugs, alcohol or

medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always

wear eye protection.

Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will

reduce personal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ -position before connecting

to power source and/or battery pack, picking

up or carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection

of dust extraction and collection facilities,

ensure these are connected and properly

used.

Use of dust collection can reduce dust-related

hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and oﬀ .

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the

risk of starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may aﬀ ect the

power tool’s operation.

If damaged, have the power tool repaired

before use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions

and the work to be performed.

Use of the power tool for operations different

from those intended could result in a hazardous

situation.

5) Battery tool use and care

a) Recharge only with the charger specified

by the manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of ﬁ re when used with

another battery pack.

b) Use power tools only with specifically

designated battery packs.

Use of any other battery packs may create a

risk of injury and ﬁ re.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips,

coins, keys, nails, screws or other small

metal objects, that can make a connection

from one terminal to another.

Shorting the battery terminals together may

cause burns or a ﬁ re.

d) Under abusive conditions, liquid may be

ejected from the battery; avoid contact.

If contact accidentally occurs, flush with

water. If liquid contacts eyes, additionally

seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualiﬁ ed

repair person using only identical replacement

parts.

This will ensure that the safety of the power tool

is maintained.

English

9. Do not use power tools if the plastic housing or

handle is cracked.

Cracks in the tool’s housing or handle can lead to

electric shock. Such tools should not be used until

repaired.

10. Blades and accessories must be securely mounted

to the tool.

Prevent potential injuries to yourself or others. Blades,

cutting implements and accessories which have been

mounted to the tool should be secure and tight.

11. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that

air can freely ﬂ ow at all times. Check for dust build-

up frequently.

12. NEVER leave tool running unattended. Turn

power oﬀ .

Don’t leave tool until it comes to a complete stop.

13. Carefully handle power tools.

Should a power tool be dropped or struck against

hard materials inadvertently, it may be deformed,

cracked, or damaged.

14. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon

tetrachloride, and alcohol may damage and crack

plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened

with soapy water and dry thoroughly.

15. ALWAYS

wear eye protection that meets the

requirement of the latest revision of ANSI

Standard Z87.1.

16. ALWAYS ﬁ rmly grip the handle while operating.

17. Deﬁ nitions for symbols used on this tool

V ............. volts

—

---

........... direct current

Hz ........... hertz

A ............. amperes

no ........... no load speed

---/min .... revolutions or reciprocation per minute

....

WARNING

– To reduce the risk

of injury, user must read instruction

manual.

18. NEVER touch the blade with bare hands after

operation.

19. Because the cordless reciprocating saw operates by

battery power, be aware of the fact that it can begin

to operate at any time.

20. When working at elevated locations, clear the area of all

other people and be aware of conditions below you.

WARNING

Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities

contains chemicals known [to the State of California] to

cause cancer, birth defects or other reproductive harm.

Some examples of these chemicals are:

●

Lead from lead-based paints,

●

Crystalline silica from bricks and cement and other

masonry products, and

●

Arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to

ﬁ lter out microscopic particles.

SPECIFIC SAFETY RULES

1. Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring.

Cutting accessory contacting a “live” wire may make

exposed metal parts of the power tool “live”and could

give the operator an electric shock.

2. Use clamps or another practical way to secure

and support the workpiece to a stable platform.

Holding the work by hand or against your body leaves

it unstable and may lead to loss of control.

3. ALWAYS wear ear protectors when using the

tool for extended periods.

Prolonged exposure to high intensity

noise can cause hearing loss.

4. NEVER touch moving parts.

NEVER place your hands, ﬁ ngers or other body parts

near the tool’s moving parts.

5. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety

features in place and in proper working order. If

maintenance or servicing requires the removal of a

guard or safety feature, be sure to replace the guard

or safety feature before resuming operation of the

tool.

6. Use right tool.

Don’t force small tool or attachment to do the job of a

heavy-duty tool.

Don’t use tool for purpose not intended —for

example— don’t use circular saw for cutting tree limbs

or logs.

7. Handle tool correctly.

Do not drop or throw the tool.

8. Keep all screws, bolts and covers tightly in

place.

Keep all screws, bolts, and plates tightly mounted.

Check their condition periodically.

English

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY AND BATTERY CHARGER

WARNING

Death or serious bodily injury could result from

improper or unsafe use of battery chargers and

battery. To avoid these risks, follow these basic

safety instructions:

CAUTION

USE ONLY HITACHI BATTERY TYPE BSL18

SERIES. OTHER TYPES OF BATTERIES MAY

BURST AND CAUSE INJURY!

1. Do not use a battery pack or appliance that is

damaged or modiﬁ ed. Damaged or modiﬁ ed batteries

may exhibit unpredictable behavior resulting in ﬁ re,

explosion or risk of injury.

2. Do not expose a battery pack or appliance to ﬁ re or

excessive temperature. Exposure to ﬁ re or temperature

above 265°F (130°C) may cause explosion.

3. This manual contains important safety and operating

instructions for battery charger Model UC18YKSL.

4. To reduce risk of injury, charge HITACHI rechargeable

battery type BSL18 series. Other type of batteries

may burst causing personal injury and damage.

5. To reduce risk of damage to electric plug and cord,

pull by plug when disconnecting battery charger.

6. Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage or stress.

7. An extension cord should not be used unless

absolutely necessary. Use of improper extension

cord could result in a risk of ﬁ re and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same

number, size, and shape as those of plug on

battery charger:

b. That extension cord is properly wired and in

good electrical condition; and

c. That wire size is large enough for AC ampere

rating of battery charger as speciﬁ ed in Table 1.

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1,250 watts

125 volts

= 10 amperes

* If the input rating of a battery charger is given in watts

rather than in amperes, the corresponding ampere

rating is to be determined by dividing the wattage

rating by the voltage rating–for example:

8. Do not operate battery charger with damaged cord or

plug-replace them immediately.

9. Do not operate battery charger if it has received a

sharp blow, been dropped, or otherwise damaged in

any way; take it to a qualiﬁ ed serviceman.

10. Do not disassemble battery charger and the battery;

take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in

a risk of electric shock or ﬁ re.

11. You must charge the battery before you can use the

power tool.

12. To reduce risk of electric shock, unplug the charger

from the electrical outlet when not in use, as well as

before maintenance or cleaning.

13. NEVER charge outdoors. Keep the battery away

from direct sunlight and use only where there is low

humidity and good ventilation.

14. NEVER charge when the temperature is below 32°F

(0°C) or above 104°F (40°C).

15. NEVER connect two battery chargers together.

16. NEVER insert any objects into the hole for the battery

or the battery charger. Electric shock or damage to

the battery and the battery charger may result.

17. NEVER use a booster transformer when charging.

18. NEVER use an engine generator or DC power to

charge.

19. NEVER store the battery or battery charger in places

where the temperature may reach or exceed 104°F

(40°C).

20. ALWAYS operate charger on standard household

electrical power (120 volts). Using the charger on any

other voltage may overheat and damage the charger.

21. ALWAYS wait at least 15 minutes between charges

to avoid overheating the charger.

English

CAUTION ON LITHIUM-ION BATTERY

To extend the lifetime, the lithium-ion battery equips with

the protection function to stop the output.

In the cases of 1 to 3 described below, when using this

product, even if you are pulling the switch, the motor may

stop. This is not the trouble but the result of protection

function.

1. When the battery power remaining runs out, the

motor stops.

In such case, charge it up immediately.

2. If the tool is overloaded, the motor may stop. In this

case, release the switch of tool and eliminate causes

of overloading. After that, you can use it again.

3. If the battery is overheated under overload work, the

battery power may stop.

In this case, stop using the battery and let the battery

cool. After that, you can use it again.

Furthermore, please heed the following warning and

caution.

WARNING

In order to prevent any battery leakage, heat generation,

smoke emission, explosion and ignition beforehand,

please be sure to heed the following precautions.

1. Make sure that swarf and dust do not collect on the

battery.



During work make sure that swarf and dust do not fall

on the battery.



Make sure that any swarf and dust falling on the

power tool during work do not collect on the battery.



Do not store an unused battery in a location exposed

to swarf and dust.



Before storing a battery, remove any swarf and dust

that may adhere to it and do not store it together with

metal parts (screws, nails, etc.).

2. Do not pierce battery with a sharp object such as a

nail, strike with a hammer, step on, throw or subject

the battery to severe physical shock.

3. Do not use an apparently damaged or deformed

battery.

4. Do not use the battery in reverse polarity.

5. Do not connect directly to an electrical outlets or car

cigarette lighter sockets.

6. Do not use the battery for a purpose other than those

speciﬁ ed.

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO OTHER USERS

AND

OWNERS OF THIS TOOL!

7. If the battery charging fails to complete even when a

speciﬁ ed recharging time has elapsed, immediately

stop further recharging.

8. Do not put or subject the battery to high temperatures

or high pressure such as into a microwave oven,

dryer, or high pressure container.

9. Keep away from fire immediately when leakage or

foul odor are detected.

10. Do not use in a location where strong static electricity

generates.

11. If there is battery leakage, foul odor, heat generated,

discolored or deformed, or in any way appears abnormal

during use, recharging or storage, immediately remove it

from the equipment or battery charger, and stop use.

CAUTION

1. If liquid leaking from the battery gets into your eyes,

do not rub your eyes and wash them well with fresh

clean water such as tap water and contact a doctor

immediately.

If left untreated, the liquid may cause eye-problems.

2. If liquid leaks onto your skin or clothes, wash well

with clean water such as tap water immediately.

There is a possibility that this can cause skin irritation.

3. If you find rust, foul odor, overheating, discolor,

deformation, and/or other irregularities when using

the battery for the ﬁ rst time, do not use and return it

to your supplier or vendor.

WARNING

If an electrically conductive foreign object enters the

terminals of the lithium ion battery, a short-circuit may

occur resulting in the risk of fire. Please observe the

following matters when storing the battery.



Do not place electrically conductive cuttings,

nails, steel wire, copper wire or other wire in the

storage case.



Either install the battery in the power tool or

store by securely pressing into the battery cover

until the ventilation holes are concealed to

prevent short-circuits (See Fig. 1).

English

FUNCTIONAL DESCRIPTION

NOTE

The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance

of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety

instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that diﬀ er from those on your own

power tool.

NAME OF PARTS

1. Cordless Reciprocating Saw (CR18DGL)



Battery (optional accesseries

...

sold separately)

Lever

Base

lever

Lock-oﬀ button

Switch trigger

Battery

(optional accesseries)

LED light

Housing

Blade

Base

Handle

Front cover

Fig. 1

Ventilation holes

Latch

Terminals

Battery cover

Battery

English

2. Battery Charger (

optional accesseries

...

sold separately

)

Fig. 2

SPECIFICATIONS

1. Cordless Reciprocating Saw

Model CR18DGL

Motor DC motor

No-load speed 0 – 3,300 /min

Stroke 1" (25 mm)

Weight (without battery) 5.7 lbs. (2.6 kg)

2. Battery Charger (optional accessories)

Model UC18YKSL

Input power source Single phase: AC120 V 60 Hz

Charging time

(At a temperature of 68°F (20°C))

BSL1815: Approx. 40 min.

BSL1830C: Approx. 90 min.

Charging voltage DC 14.4 V – 18 V

Charging current DC 2.0 A

Weight 0.8 lbs. (0.35 kg)

NOTE: The charging time may vary according to ambient temperature and power source voltage.

Nameplate

Pilot lamp

Guide rail

English

APPLICATIONS



Cutting metal and stainless steel pipe.



Cutting various lumber.



Cutting mild steel, aluminum and copper plate.



Cutting synthetic resins, such as phenol resin and

vinyl chloride.

REMOVAL AND INSTALLATION METHOD

OF BATTERY



How to install the battery.

Align the battery with the groove in tool handle and

slip it into place.

Always insert it all the way until it locks in place with a

little click, If not, it may accidentally fall out of the tool,

causing injury to you or someone around you (Fig. 3).



How to remove the battery.

Withdraw battery from the tool handle while pressing

the latch (2 pcs) of the battery (Fig. 3).

Latch

Handle

Battery

Pull out

Push

Insert

ASSEMBLY AND OPERATION

Fig. 3

CHARGING METHOD

NOTE

Before plugging into the receptacle, make sure the

following points.



The power source voltage is stated on the nameplate.



The cord is not damaged.

WARNING

Do not charge at voltage higher than indicated

on the nameplate.

If charged at voltage higher than indicated on

the nameplate, the charger will burn out.

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted

into the receptacle, pilot lamp will blink in red. (At

1-second intervals)

Battery

Pilot lamp

WARNING

Do not use the electrical cord if

damaged. Have it repaired immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as shown in

Fig. 4. Make sure it contacts the bottom of the battery

charger.

Fig. 4

3. Charging



When the battery is connected to the battery charger,

charging will commence and the pilot lamp will light

in red. (See Table 2)

NOTE

If the pilot lamp does not light or blink in red, pull out

the plug from the receptacle and check if the battery

is properly mounted.



When the battery is fully charged, the pilot lamp

will blink in red slowly. (At 1-second intervals) (See

Table 2)

English



Regarding the temperature of the rechargeable

battery.

The temperatures for rechargeable batteries are as

shown in Table 3, and batteries that have become hot

should be cooled for a while before being recharged.

Table 3

Rechargeable

batteries

Temperatures at which the

battery can be recharged

BSL1815, BSL1830C 32°F – 122°F (0°C – 50°C)

4. Disconnect battery charger from the receptacle.

CAUTION

Do not pull the plug out of the receptacle by

pulling on the cord.

Make sure to grasp the plug when removing

from receptacle to avoid damaging cord.

5. Remove the battery from the battery charger.

Supporting the battery charger with hand, pull out the

battery from the battery charger.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new

batteries and batteries that have not been used for

an extended period is not activated, the electric

discharge might be low when using them the ﬁ rst and

second time. This is a temporary phenomenon, and

normal time required for recharging will be restored

by recharging the batteries 2 – 3 times.

Indications of the pilot lamp

Pilot lamp

(red)

Before

charging

Blinks

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

While

charging

Lights

Lights continuously

Charging

complete

Blinks

Lights for 0.5 seconds. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Overheat

standby

Blinks

Lights for 1 second. Does not light

for 0.5 seconds. (oﬀ for 0.5 seconds)

Battery overheated.

Unable to charge.

(Charging will

commence when

battery cools)

Charging

impossible

Flickers

Lights for 0.1 seconds. Does not light

for 0.1 seconds. (oﬀ for 0.1 seconds)

Malfunction in the

battery or the charger

CAUTION

●

When the battery charger has been continuously

used, the battery charger will be heated, thus

constituting the cause of the failures. Once the

charging has been completed, give 15 minutes

rest until the next charging.

●

If the battery is charged while it is heated because

it has been left for a long time in a location subject

to direct sunlight or because the battery has just

been used, the pilot lamp of the charger lights for

1 second, does not light for 0.5 seconds (oﬀ for 0.5

seconds).

The battery will not be recharged. In such a case,

let the battery cool before charging.

●

When the pilot lamp flickers (at 0.2-second

intervals), check for and take out any foreign

objects in the charger’s battery connector. If there

are no foreign objects, it is probable that the

battery or charger is malfunctioning. Take it to your

authorized Service Center.

NOTE



Charging times may be longer depending on the

surrounding temperature and battery conditions.



Charge time lamp indications are only a guide, and

may vary depending on the surrounding temperature

and battery conditions.



Remove the battery from the charger when not in use.

How to make the batteries perform longer.



Recharge the batteries before they become completely

exhausted.

Table 2

English

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery. If

you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.



Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

PRIOR TO OPERATION

CAUTION

To avoid serious accident, ensure the switch is

in the OFF position, and pull out the battery.

1. Check the work area environment

Check the work area to make sure that it is clear of

debris and clutter.

Clear the area of unnecessary personnel. Ensure that

lighting and ventilation is adequate.

2. Mounting the blade

This unit employs a detachable mechanism that

enables mounting and removal of saw blades without

the use of a wrench or other tools.

(1) Pivot the lever to open the blade clamp.

(2) Insert the saw blade all the way into the small slit of

the plunger tip with the lever pivoting. You can mount

this blade either in the upward or downward direction.

(Fig. 5, Fig. 6)

Fig. 5

Blade

Lever

Slit of plunger

Blade

Lever

Slit of plunger

Fig. 6

(3) When you release the lever, the spring force will return

the lever to the correct position automatically.

(4) Pull the back of the saw blade two or three times by

hand and check that the blade is securely mounted.

(Fig. 7)

Fig. 7

Lever

Blade

CAUTION

When pulling the saw blade, be absolutely sure

to pull it from the back. Pulling other parts of the

blade will result in an injury.

3. Dismounting the blade

CAUTION

Never touch the saw blade immediately after

use. The metal is hot and can easily burn your

skin.

(1) After pivoting the lever, point the blade downward.

The blade should fall out on its own. If the blade fails

to fall out, pull it out by hand.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and remains

inside the small slit of the plunger, it should fall out

when the lever is pivoted and the blade is pointed

downward. If the blade fails to fall out on its own, take

it out by using the procedures described below.

(1) If a part of the broken saw blade is sticking out of the

small slit of the plunger, pull out the protruding part

and take the blade out.

(2) If the broken saw blade is hidden inside the small

slit, hook the broken blade using a tip of another saw

blade and take it out. (Fig. 8)

Another blade

Lever

Fig. 8

English

MAINTENANCE AND INSPECTION OF SAW BLADE

MOUNT

(1) After use, blow away sawdust, earth, sand, moisture,

etc., with air or brush them away with a brush, etc., to

ensure that the blade mount can function smoothly.

NOTE

Continued use of the tool without cleaning the

area where the saw blade is attached can result in

sawdust and chip buildup which may adversely aﬀ ect

the movement of the lever. Should this be the case,

pivot the lever and clean around the plunger and

lever by wiping or blowing away the buildup.

CAUTION

Do not use any saw blade with a worn-out blade

hole. Otherwise, the saw blade can come off,

resulting in personal injury. (Fig. 9)

Fig. 9

Blade hole

Blade

4. Adjusting the base

To maximize blade life, the base slides in or out

to allow the stroke length to be adjusted for better

eﬃ ciency.

(1) Turn oﬀ the switch and remove the battery.

(2) Pivot the base lever clockwise; and slide the base to

the desired position. There are ﬁ ve positions that the

base can be adjusted to.

(3) Pivot the base lever counterclockwise to secure the

base. (Fig. 10)

Base

Base lever

Fig. 10

(4) Make sure that the base is not interfering with the

blade

WARNING

To avoid injury and damage, do not operate the

saw without the base in place. The plunger may

strike against the workpiece and damage the

reciprocating mechanism.

5. Check battery insertion

WARNING

If the battery is inserted while the power switch

is in the ON position, the power tool will start

operating immediately, inviting serious accident.

CAUTION

Until the battery locks in place with a little click,

if not, it may accidentally fall out of the tool

causing injury to you or someone around you.

OPERATION

WARNING

Never touch the moving parts.

CAUTION



Be careful not to let sawdust, earth, moisture,

etc., enter the inside of the machine through

the plunger section during operation. If sawdust

and the like accumulate in the plunger section,

always clean it before use.



Do not remove the front cover (refer to Fig. 1).

Be sure to hold the body from the top of the

front cover.



During use, press the base against the material

while cutting.

Vibration can damage the saw blade if the base

is not pressed ﬁ rmly against the workpiece.

Furthermore, a tip of the saw blade can sometimes

contact the inner wall of the pipe, damaging the

saw blade.



Select a saw blade of the most appropriate

length. Ideally, the length protruding from the

base of the saw blade after subtracting the

stroke should be larger than the material (see

Fig. 11 and Fig. 13).

If you cut a large pipe, large block of wood, etc.,

that exceeds the cutting capacity of a blade;

there is a risk that the blade may contact with

the inner wall of the pipe, wood, etc., resulting in

damage. (Fig. 12, Fig. 14)

English

Fig. 11

Storke

Fig. 12

Fig. 13 Fig. 14

Storke



To extend the lifetime, the lithium-ion battery

equips with the protection function to stop the

output. Therefore, if the tool is overloaded, the

motor may stop. However, this is not the trouble

but the result of protection function. In this case,

release the switch of tool and eliminate the

causes of overloading.



Don’t remove the tool from workpiece during a

cut while the saw blade is moving.



Pull out the battery after completing operation.

NOTE

Take care not to lock the motor. If the motor is locked,

immediately turn the power oﬀ . If the motor is locked

for a while, the motor or battery may be burnt.

1. Switch operation

(1) Lock-oﬀ button

The tool is equipped with a lock-oﬀ button. To start

the tool, press the lock-oﬀ button and then squeeze

the trigger switch. (Fig. 15)

Fig. 15

Lock-oﬀ button

Triggger

switch

CAUTION

Do not ﬁ x and secure the lock-oﬀ button.

Besides, keep your ﬁ nger oﬀ the trigger switch

when the tool is being carried around. Otherwise,

the trigger switch can be inadvertently turned

ON, resulting in unexpected accidents.

(2) Trigger switch



This tool is equipped with a variable speed controlled

trigger switch. The tool can be turned “ON” or

“OFF” by squeezing or releasing the trigger. The

blade plunger stroke rate can be adjusted from the

minimum to maximum nameplate stroke rate by

the pressure you apply to the trigger. Apply more

pressure to increase the speed and release pressure

to decrease speed.



When the trigger switch is turned on, an LED lamp

lights. This lamp goes out when the trigger switch is

released.

CAUTION

Do not look directly into the light from the LED

lamp. Continuous and direct exposure to the

light from the LED lamp can injure your eyes.

LED light

Fig. 16

2. Cutting metallic materials

CAUTION



Press the base ﬁ rmly against the workpiece.



Never apply any unreasonable force to the saw

blade when cutting. Doing so can easily break

the blade.



The motor can be locked sometimes, depending

on the combination of the material to be cut

and the blade. Whenever the motor gets locked,

switch it oﬀ immediately.



Do not operate power tools in explosive atmospheres,

such as in the presence of ﬂ ammable liquids, gases

or dust. Reciprocating saw create sparks which

may ignite the dust or fumes.

(1) Fasten a workpiece ﬁ rmly before operation. (Fig. 17)

Fig. 17

English

(2) When cutting metallic materials, use proper machine

oil (turbine oil, etc.). When not using liquid machine

oil, apply grease over the workpiece.

CAUTION

The service life of the saw blade will be drastically

shortened if you don’t use machine oil.

3. Cutting lumber

When cutting lumber, make sure that the workpiece

is fastened ﬁ rmly before beginning. (Fig. 18)

Fig. 18

CAUTION

Never apply any unreasonable force to the saw

blade when cutting. Also remember to press the

base against the lumber ﬁ rmly.

4. Sawing curved lines

We recommend that you use the BIMETAL blade

mentioned in Page 18 for the saw blade since it is

tough and hardly breaks.

CAUTION

Delay the feed speed when cutting the material

into small circular arcs. An unreasonably fast

feed may break the blade.

5. Plunge cutting

With this tool, you can perform plunge cutting on

plywood panels and thin board materials. You can

carry out plunge cutting quite easily with the saw

blade installed in reverse as illustrated in Fig. 20,

Fig. 22, and Fig. 24. Use the saw blade that is as

short and thick as possible. We recommend for

this purpose that you use BI-METAL Blade No. 132

mentioned in Page 18. Be sure to use caution during

the cutting operation and observe the following

procedures.

(1) Press the lower part (or the upper part) of the base

against the material. Pull the switch trigger while

keeping the tip of the saw blade apart from the

material. (Fig. 19, Fig. 20)

(2) Raise the handle slowly and cut in with the saw blade

little by little. (Fig. 21, Fig. 22)

(3) Hold the body ﬁ rmly until the saw blade completely

cuts into the material. (Fig. 23, Fig. 24)

Fig. 23 Fig. 24

Fig. 19 Fig. 20

Fig. 21 Fig. 22

CAUTION



Avoid plunge cutting for metallic materials. This

can easily damage the blade.



Never pull the switch trigger while the tip of the

saw blade is pressed against the material. If you

do so, the blade can easily be damaged when it

collides with the material.



Make absolutely sure that you cut slowly

while holding the body ﬁ rmly. If you apply any

unreasonable force to the saw blade during

the cutting operation, the blade can easily be

damaged.

English

WARNING

Be sure to turn oﬀ the switch and pull out the battery before doing any inspection or maintenance.

MAINTENANCE AND INSPECTION

1. Inspecting the blade

Continued use of a dull or damaged blade will

result in reduced cutting efficiency and may cause

overloading of the motor. Replace the blade with a

new one as soon as excessive abrasion is noted.

CAUTION

If a dull saw blade is used, reactive force is

increased during cutting operation. Avoid the

use of the dull saw blade without repair.

2. Check the Screws

Loose screws are dangerous. Regularly inspect them

and make sure they are tight.

CAUTION

Using this power tool with loosened screws is

extremely dangerous.

3. Maintenance of the motor

The motor unit winding is the very “heart” of the

power tool. Exercise due care to ensure the winding

does not become damaged and/or wet with oil or

water.

4. Check for Dust

Dust may be removed with a soft cloth or a cloth

dampened with soapy water.

Do not use bleach, chlorine, gasoline or thinner, for

they may damage the plastics.

5. Lubrication

The bearings in this tool have been sufficiently

lubricated with quality lubricating oil, taking into

account the expected life of this tool under normal

operating conditions. As a result, no further

lubrication is necessary.

6. Disposal of the exhausted battery

WARNING

Do not dispose of the exhausted battery. The

battery must explode if it is incinerated. The battery

is recyclable. At the end of it’s useful life, under

various state and local laws, it may be illegal to

dispose of this battery into the municipal waste

stream. Check with your local solid waste oﬃ cials

for details in your area for recycling options or

proper disposal.

7. Storage

Storing in a place below 104°F (40°C) and out of the

reach of children.

NOTE

Make sure that the battery is fully charged when

stored for a long period (3 months or more). The

battery with smaller capacity may not be able to be

charged when used, if stored for a long period.

NOTE

Storing lithium-ion batteries

Make sure the lithium-ion batteries have been fully

charged before storing them.

Prolonged storage of batteries with a low charge

may result in performance deterioration, signiﬁ cantly

reducing battery usage time or rendering the

batteries incapable of holding a charge.

However, significantly reduced battery usage time

may be recovered by repeatedly charging and using

the batteries two to ﬁ ve times.

If the battery usage time is extremely short despite

repeated charging and use, consider the batteries

dead and purchase new batteries.

8. Service and repairs

All quality power tools will eventually require servicing

or replacement of parts because of wear from normal

use. To assure that only authorized replacement

parts will be used, all service and repairs must be

performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

9. Service parts list (Page 53)

CAUTION

Repair, modification and inspection of Hitachi

Power Tools must be carried out by a Hitachi

Authorized Service Center.

This Parts List will be helpful if presented with

the tool to the Hitachi Authorized Service Center

when requesting repair or other maintenance. In

the operation and maintenance of power tools,

the safety regulations and standards prescribed

in each country must be observed.

MODIFICATIONS

Hitachi Power Tools are constantly being improved

and modiﬁ ed to incorporate the latest technological

advancements.

Accordingly, some parts may be changed without

prior notice.

English

ACCESSORIES

WARNING

ALWAYS use Only authorized HITACHI replacement parts and accessories. NEVER use replacement parts

or accessories which are not intended for use with this tool. Contact HITACHI if you are not sure whether

it is safe to use a particular replacement part or accessory with your tool.

The use of any other attachment or accessory can be dangerous and could cause injury or mechanical

damage.

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

OPTIONAL ACCESSORIES.....sold separately

1. Battery (BSL1815) (Code No. 333353)

Battery (BSL1830C) (Code No. 339782)

2. Battery charger (UC18YKSL)

3. Battery cover (Code No. 329897)

CR18DGL

(NN)



Blade for wood ................................................................................... 2

Battery, battery charger and battery cover are not contained.

Important notice on the batteries for the Hitachi

cordless power tools

Please always use one of our designated genuine

batteries. We cannot guarantee the safety and

performance of our cordless power tool when used

with batteries other than these designated by us, or

when the battery is disassembled and modiﬁ ed (such

as disassembly and replacement of cells or other

internal parts).

English

4. Saw Blades

PROG.: NEW PROGRESSIVE TOOTH HCS: HIGHSPEED CARBON STEEL

NOTE: Speciﬁ cations are subject to change without any obligation on the part of the HITACHI.

TYPE LENGTH WIDTH TPI MATERIAL CODE NO.

BLADES /

POUCH

WOOD CUTTING

6" (152 mm) 3/4" (18 mm) 6 HCS 725300 5

9" (228 mm) 3/4" (18 mm) 5 HCS 725301 5

12" (305 mm) 3/4" (18 mm) 6 HCS 725302 5

WOOD CUTTING

NAIL-EMBEDED

6" (152 mm) 3/4" (18 mm) 6 BI-METAL 725310 5

6" (152 mm) 3/4" (18 mm) 6 BI-METAL 725311 5

6" (152 mm) 5/8" (16 mm) 6 BI-METAL 725312 5

9" (228 mm) 3/4" (18 mm) 6 BI-METAL 725313 5

12" (305 mm) 3/4" (18 mm) 6 BI-METAL 725314 5

METAL CUTTING

6" (152 mm) 3/4" (18 mm) 10 BI-METAL 725320 5

9" (228 mm) 3/4" (18 mm) 10 BI-METAL 725321 5

6" (152 mm) 3/4" (18 mm) 14 BI-METAL 725322 5

9" (228 mm) 3/4" (18 mm) 14 BI-METAL 725323 5

6" (152 mm) 3/4" (18 mm) 18 BI-METAL 725324 5

9" (228 mm) 3/4" (18 mm) 18 BI-METAL 725326 5

6" (152 mm) 3/4" (18 mm) 24 BI-METAL 725325 5

9" (228 mm) 3/4" (18 mm) 24 BI-METAL 725327 5

ALL PURPOS

6" (152 mm) 3/4" (18 mm) 10//14 BI-METAL 725330 5

9" (228 mm) 3/4" (18 mm) 10//14 BI-METAL 725331 5

12" (305 mm) 3/4" (18 mm) 10//14 BI-METAL 725332 5

CARBIDE GRIT 9" (228 mm) 3/4" (18 mm) GRIT — 725340 3

DEMOLITION

9" (228 mm) 7/8" (22 mm) 6 BI-METAL 725350 3

9" (228 mm) 7/8" (22 mm) 9 BI-METAL 725351 3

NEW WOOD 6" (152 mm) 3/4" (18 mm) PROG. BI-METAL 725360 5

NEW METAL 6" (152 mm) 3/4" (18 mm) PROG. BI-METAL 725361 5

NEW ALL PURPOSE 8" (203 mm) 3/4" (18 mm) PROG. BI-METAL 725362 5

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions de fonctionnement dans ce

mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé proviennent d’un non respect des

règles ou précautions de base de sécurité. Un accident peut la plupart du temps être évité si l’on reconnaît une situation

de danger potentiel avant qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE” de ce mode d’emploi et dans

les sections qui contiennent les instructions de fonctionnement et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un endommagement de la machine sont

identiﬁ és par AVERTISSEMENTS sur l’outil motorisé et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spéciﬁ quement recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont ignorées, pourraient entraîner la

mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées, peuvent entraîner de mineures

et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

SÉCURITÉ

AVERTISSEMENTS DE SÉCURITÉ GÉNÉRAUX CONCERNANT LES OUTILS ÉLECTRIQUES

AVERTISSEMENT

Lire tous les avertissements de sécurité et toutes les instructions

Tout manquement à observer ces avertissements et instructions peut engendrer des chocs électriques, des incendies

et/ou des blessures graves.

Conservez tous les avertissements et toutes les instructions pour vous y référer ultérieurement.

Le terme “outil électrique”, utilisé dans les avertissements, se réfère aux outils électriques (câblé) ou aux outils à

piles (sans ﬁ l).

1) Sécurité de l’aire de travail

a) Maintenir l’aire de travail propre et bien éclairée.

Les endroits encombrés ou sombres sont

propices aux accidents.

b) Ne pas utiliser d’outils électriques en

présence de liquides, gaz ou poussière

inﬂ ammables, au risque de provoquer une

explosion.

Les outils électriques créent des étincelles

susceptibles d’enﬂ ammer la poussière.

c) Ne pas laisser les enfants et les visiteurs

s’approcher de vous lorsque vous utiliser

un outil électrique.

Les distractions peuvent faire perdre le contrôle.

2) Sécurité électrique

a) Les prises de l’outil électrique doivent

correspondre à la prise secteur.

Ne jamais modiﬁ er la prise.

Ne pas utiliser d’adaptateurs avec les outils

électriques mis à la masse.

Les prises non modiﬁ ées et les prises secteurs

correspondantes réduisent les risques de choc

électrique.

b) Eviter tout contact avec les surfaces mises

à la masse telles que les tuyaux, radiateurs,

bandes et réfrigérateurs.

Le risque de choc électrique est accru en cas de

mise à la masse du corps.

c) Ne pas exposer les outils électriques à la

pluie ou à des conditions humides.

Si l’eau pénètre dans l’outil, cela augmente les

risques de choc électrique.

d) Ne pas utiliser le cordon à tort. Ne jamais

utiliser le cordon pour transporter ou

débrancher l’outil électrique.

Maintenir le cordon loin de la chaleur, de l’huile,

des bords pointus ou des pièces mobiles.

Les cordons endommagés ou usés augmentent

les risques de choc électrique.

Français

e) En cas d’utilisation d’un outil électrique à

l’extérieur, utiliser un cordon de rallonge

adapté à un usage extérieur.

L’utilisation d’un cordon adapté à l’usage extérieur

réduit les risques de choc électrique.

f) Si vous devez utiliser un outil électrique dans

un endroit humide, utilisez une alimentation

protégée contre les courants résiduels.

L’utilisation d’un dispositif de protection contre

les courants résiduels réduit le risque de choc

électrique.

3) Sécurité personnelle

a) Restez alerte, regarder ce que vous faites et

usez de votre bon sens en utilisant un outil

électrique.

Ne pas utiliser d’outil électrique si vous êtes

sous l’inﬂ uence de drogues, d’alcool ou de

médicaments.

Pendant l’utilisation d’outils électrique, un instant

d’inattention peut entraîner des blessures graves.

b) Utiliser un équipement de protection

individuelle. Toujours porter des verres de

protection.

L’utilisation d’équipements de protection tels

que les masques anti-poussière, les chaussures

de sécurité anti-dérapantes, les casques ou

les protections auditives dans des conditions

appropriées réduisent les risques de blessures.

c) Empêcher les démarrages intempestifs.

Veiller à ce que l’interrupteur soit en

position d’arrêt avant de brancher à une

source d’alimentation et/ou une batterie, de

ramasser l’outil au sol ou de le transporter.

Transporter les outils électriques avec le doigt sur

l’interrupteur ou brancher les outils électriques

avec l’interrupteur en position de marche peut

entraîner des accidents.

d) Retirer toute clé de sécurité ou clé avant de

mettre l’outil électrique en marche.

Laisser une clé ou une clé de sécurité sur une

partie mobile de l’outil électrique peut engendrer

des blessures.

e) Ne pas trop se pencher. Toujours garder une

bonne assise et un bon équilibre pendant le

travail.

Cela permet un meilleur contrôle de l’outil

électrique dans des situations imprévisibles.

f) Porter des vêtements adéquats. Ne pas

porter de vêtements amples ni de bijoux.

Maintenir les cheveux, les vêtements et les

gants loin des pièces mobiles.

Les vêtements amples ou les cheveux longs

peuvent se prendre dans les pièces mobiles.

g) En cas de dispositifs destinés au

raccordement d’installations d’extraction et

de recueil de la poussière, veiller à ce qu’ils

soient correctement raccordés et utilisés.

L’utilisation d’un dispositif de collecte de la

poussière peut réduire les dangers associés à

la poussière.

4) Utilisation et entretien d’un outil électrique

a) Ne pas forcer sur l’outil électrique. Utiliser

l’outil électrique adapté à vos travaux.

Le bon outil électrique fera le travail mieux et en

toute sécurité au régime pour lequel il a été conçu.

b) Ne pas utiliser l’outil électrique si l’interrupteur

ne le met pas en position de marche et d’arrêt.

Tout outil ne pouvant être contrôlé par l’interrupteur

est dangereux et doit être réparé.

c) Débrancher la prise ou retirer la batterie

avant de procéder à des réglages, au

remplacement des accessoires ou au

stockage des outils électriques.

Ces mesures préventives de sécurité réduisent

les risques de démarrage accidentel de l’outil

électrique.

d) Stockez les outils électriques inutilisés hors

de la portée des enfants et ne pas laisser des

personnes non familiarisées avec l’outil ou

ces instructions utiliser l’outil électrique.

Les outils électriques sont dangereux entre les

mains d’utilisateurs non habilités.

e) Entretenir les outils électriques. Vérifier

l’absence de mauvais alignement ou d’arrêt,

d’endommagement de pièces ou toute autre

condition susceptible d’aﬀ ecter l’opération

de l’outil.

Si l’outil est endommagé, le faire réparer

avant utilisation.

De nombreux accidents sont dus à des outils mal

entretenus.

f) Maintenir les outils coupants aiguisés et

propres.

Des outils coupants bien entretenus avec des

bords aiguisés sont moins susceptibles de se

coincer et plus simples à contrôler.

g) Utiliser l’outil électrique, les accessoires

et les mèches de l’outil, etc. conformément

à ces instructions en tenant compte des

conditions d’utilisation et du travail à réaliser.

L’utilisation de l’outil électrique pour des

opérations diﬀ érentes de celles pour lesquelles

il a été conçu est dangereuse.

5) Utilisation et entretien de la batterie

a) Recharger la batterie uniquement avec le

chargeur recommandé par le fabricant.

Un chargeur inadéquat pour le type de batterie

peut entraîner un risque d’incendie en cas

d’utilisation avec une autre batterie.

b) Utiliser les outils électriques uniquement

avec les batteries spéciﬁ ées.

L’utilisation d’autres batteries peut entraîner un

risque de blessures et d’incendie.

La page charge ...

Hitachi CR 18DGL Manuel utilisateur

Marque: Hitachi

Modèle: CR 18DGL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi CR 18DGL User manual
español: Hitachi CR 18DGL Manual de usuario

Hitachi CR 18DGL Manuel utilisateur

Hitachi CR 18DGL Manuel utilisateur

dans d''autres langues

Documents connexes