GE KRCR24 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
Use and Care Manual
INDOOR PRESERVATION
Refrigerators and Freezers
KRP / KRB / KRC / KFC
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY
BEFORE INSTALLING OR USING YOUR APPLIANCE TO REDUC
E
THE RISK OF FIRE, BURN HAZARD, OR OTHER INJURY. KEEP
THIS MANUAL FOR FUTURE REFERENCE.
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed by a qualified installer or service agency.
DO NOT REPAIR, REPLACE OR REMOVE ANY PART OF THE APPLIANCE UNLESS
SPECIFICALLY RECOMMENDED IN THE MANUAL. IMPROPER INSTALLATION,
SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE. REFER
TO THIS MANUAL FOR GUIDANCE. ALL OTHER SERVICING SHOULD BE DONE BY A
QUALIFIED TECHNICIAN.
INSTALLER: LEAVE THIS MANUAL WITH THE OWNER OF THE APPLIANCE.
HOMEOWNER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY
DAMAGE, PERSONAL INJURY, OR DEATH.
SAFETY DEFINITIONS
THIS INDICATES THAT DEATH OR SERIOUS INJURY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING
THIS INDICATES THAT MINOR OR MODERATE INJURY MAY
OCCUR AS A RESULT OF NOT OBSERVING THIS WARNING.
THIS INDICATES THAT DAMAGE TO THE APPLIANCE OR
PROPERTY MAY OCCUR AS A RESULT OF NOT OBSERVING
THIS WARNING.
Message from Hestan:
Hestan’s award-winning culinary innovations and purpose-built features
reinvented the restaurant kitchen and redefined culinary experience in some
of America’s most acclaimed restaurants. Hestan now takes this performance
from the back of the house and puts it front and center in yours. Thoughtfully
designed and meticulously built, Hestan will serve you beautifully for years to
come.
Hestan is the only residential brand born from the dreams and demands of
professional chefs. From ranges to refrigeration, every detail is designed to
deliver the performance and reliability expected in a restaurant – now available
for you.
We appreciate you choosing Hestan, and we promise to deliver the very best to
you.
Welcome to Hestan
©2019 Hestan Commercial Corporation
1
EN
TABLE OF CONTENTS
3 SAFETY PRECAUTIONS - BEFORE YOU BEGIN
6 MODEL NUMBERS
7 RATING LABEL
7 REGULATORY / CODE REQUIREMENTS
8 GETTING TO KNOW YOUR APPLIANCE
12 CONTROLS AND OPERATION
21 INTERNAL LAYOUT
25 FOOD PRESERVATION
28 CARE AND CLEANING
29 TROUBLESHOOTING
32 MAP OF FUNCTIONS AND SETTINGS
34 PARTS / SERVICE
35 LIMITED WARRANTY
SAFETY PRECAUTIONS - BEFORE YOU BEGIN
When properly cared for, your Hestan appliance will provide safe, reliable service for many
years. When using this appliance, basic safety practices must be followed as outlined below.
IMPORTANT: Save these instructions for the local Utility Inspector’s use.
INSTALLER: Please leave these instructions with the owner.
OWNER: Please retain these instructions for future reference.
This appliance is NOT designed for installation in manufactured (mobile) homes or recreational
park trailers. Do NOT install this appliance outdoors.
ELECTRICAL SHOCK HAZARD
Disconnect power before installing or servicing appliance. Failure
to do so can result in death or electrical shock.
ELECTRICAL GROUNDING
This appliance must be grounded. Grounding reduces the
risk of electric shock in the event of a short circuit. Read the
ELECTRICAL CONNECTIONS section of the Installation
Manual for complete instructions.
DO NOT ground to a gas pipe.
DO NOT use an extension cord with this appliance.
DO NOT have a fuse in the NEUTRAL or GROUNDING circuit. A fuse in the NEUTRAL or
GROUNDING circuit could result in an electrical shock.
©2019 Hestan Commercial Corporation
3
EN
GENERAL SAFETY PRECAUTIONS
If this appliance is replacing an existing appliance which must be removed or
disposed of, make sure that it does not become a dangerous trap for children
by cutting its power supply cable and rendering it impossible to close the door.
Use the same caution at the end of the lifespan of the new appliance.
This appliance is designed to refrigerate beverages and foods and is intended for
domestic use.
The appliance must be installed by following the instructions in the Installation
Guide. Particular care should be taken not to obstruct the vent openings of the
appliance and of the built-in units.
The appliance features a concentrated lighting system with LED lamps. Do not stare into these
lamps when they are on to avoid possible eyesight damage.
This warning is also contained on the label attached to the inside of the refrigerator door.
When the freezer is functioning do not touch the inner stainless steel surfaces with wet or
damp hands, since skin may stick to the very cold surfaces.
Do not use any type of electrical equipment inside of the food conservation compartments.
When positioning the shelves, do not place fingers in the shelf slide guides.
Do not position containers of flammable liquids near the appliance.
Completely switch off the appliance and unplug the power supply cable during cleaning
operations.
The packaging parts can be dangerous for children: do not allow children to play with the
plastic bags, plastic film or Styrofoam.
Any repairs must be performed by a qualified Hestan Service technician.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or lack of experience and knowledge unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
CARING FOR THE ENVIRONMENT
Pay special attention to correct disposal procedure for all the packaging materials.
The appliance must not be disposed of with urban waste. Contact local waste
disposal centers on how to dispose of recyclable waste.
Prior to disposal, cut the power supply cord and make it impossible to close the
door, as stated in “GENERAL SAFETY PRECAUTIONS” above. During disposal,
avoid damage to the electronics.
The appliance does not contain hazardous substances for the atmospheric ozone layer, neither
in the electronics nor in the insulation.
B09001301
Product tested in accordante with EN62471
Risk Group 2
PRUDENZA:
NON FISSARE LA LAMPADA IN FUNZIONE.
PUÒ ESSERE DANNOSO PER GLI OCCHI.
CAUTION:
DO NOT STARE AT OPERATING LAMP.
MAY BE HARMFUL TO THE EYES.
SAFETY PRECAUTIONS - BEFORE YOU BEGIN
(CONT.)
©2019 Hestan Commercial Corporation
4
EN
SAFETY PRECAUTIONS - BEFORE YOU BEGIN
(CONT.)
CLEANING AND MAINTENANCE OF THE ICE DISPENSER
Failure to properly sanitize the ice maker system can compromise the hygienic safety of the
water dispensed. Always follow sanitization instructions.
When using the appliance for the first time and every time the filter is changed, it is
recommended to let the water flow in the circuit using the “Manual Cleaning” function and
discard the ice produced in the first 24 hours. See “ACTIVATING THE ICE MAKER” on page
13.
Clean the ice bucket or drawer regularly using only drinking water.
The filter must be changed when indicated on the control panel or when the ice/water
dispenser has not been used for more than 30 days.
With each filter replacement, sanitize the ice and/or water distribution system using a food
grade disinfectant (with sodium hypochlorite), which does not alter the characteristics of the
materials. Run the “Manual Cleaning” function so that at least 1/2 gallon of water has come
through into the catch pan before use.
Only original spare parts supplied by the manufacturer should be used when replacing
components in the ice and water dispenser.
Any work on the appliance must be carried out by a qualified technician.
USING THE CONTROL MENUS
Depending on the appliance model, there may be one or two control panels, with various
controls available. Up/Down arrows
are provided to directly adjust temperatures in the
various cooling/refrigeration/freezer zones. When two panels are present, only the main
panel has the
and buttons.
Many features and settings are only accessible through the control menus. Here are the basics:
1) Touch the key to activate the interactive menu system.
If the display shows “KEYPAD LOCKED”, touch the
and Down key for several
seconds. (See “UNLOCKING THE KEYPAD” on page 14)
Either set of the up/down buttons will move the menu selections. The active selection
is always shown in the display.
2) Use the Up/Down buttons to show a selection, then touch the button to activate it.
You may need to use the up/down buttons again to get to a final selection. When
turning selections ON or OFF, you will have to actually follow down to that ON or OFF
and touch
to confirm it.
3) To go back out of the menu, touch the button as needed.
See also: “SPECIAL SETTINGS AND FUNCTIONS” on page 14.
©2019 Hestan Commercial Corporation
5
EN
MODEL NUMBERS
REFRIGERATION MODELS
Model No. Description
KRPR36 Bottom Mount Refrigerator, Top Compressor, Pro, Right Hinged, 36"
KRPL36 Bottom Mount Refrigerator, Top Compressor, Pro, Left Hinged, 36"
KRPR36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Right Hinged, 36"
KRPL36-XX Bottom Mount Refrigerator, Top Compressor, Pro, Color, Left Hinged, 36"
KRBR36 Bottom Mount Refrigerator, Bottom Compressor, Right Hinged, 36"
KRBL36 Bottom Mount Refrigerator, Bottom Compressor, Left Hinged, 36"
KRBR36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Right Hinged, 36"
KRBL36-OV Bottom Mount Refrigerator, Bottom Compressor, Overlay, Left Hinged, 36"
KRBR36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Right Hinged, 36"
KRBL36-XX Bottom Mount Refrigerator, Bottom Compressor, Color, Left Hinged, 36"
KRCR24 Refrigerator Column, Right Hinged, 24"
KRCL24 Refrigerator Column, Left Hinged, 24"
KRCR24-OV Refrigerator Column, Overlay, Right Hinged, 24"
KRCL24-OV Refrigerator Column, Overlay, Left Hinged, 24"
KRCR24-XX Refrigerator Column, Color, Right Hinged, 24"
KRCL24-XX Refrigerator Column, Color, Left Hinged, 24"
KRCR30 Refrigerator Column, Right Hinged, 30"
KRCL30 Refrigerator Column, Left Hinged, 30"
KRCR30-OV Refrigerator Column, Overlay, Right Hinged, 30"
KRCL30-OV Refrigerator Column, Overlay, Left Hinged, 30"
KRCR30-XX Refrigerator Column, Color, Right Hinged, 30"
KRCL30-XX Refrigerator Column, Color, Left Hinged, 30"
Model No. Description
KFCR24 Freezer Column, Right Hinged, 24"
KFCL24 Freezer Column, Left Hinged, 24"
KFCR24-OV Freezer Column, Overlay, Right Hinged, 24"
KFCL24-OV Freezer Column, Overlay, Left Hinged, 24"
KFCR24-XX Freezer Column, Color, Right Hinged, 24"
KFCL24-XX Freezer Column, Color, Left Hinged, 24"
KFCR30 Freezer Column, Right Hinged, 30"
KFCL30 Freezer Column, Left Hinged, 30"
KFCR30-OV Freezer Column, Overlay, Right Hinged, 30"
KFCL30-OV Freezer Column, Overlay, Left Hinged, 30"
KFCR30-XX Freezer Column, Color, Right Hinged, 30"
KFCL30-XX Freezer Column, Color, Left Hinged, 30"
FREEZER MODELS
©2019 Hestan Commercial Corporation
6
EN
RATING LABEL
The rating label contains important information about your Hestan appliance such as the model
and serial number and electrical rating.
The rating label is located on the inside wall of the refrigerator.
TYPICAL RATING LABEL
REGULATORY / CODE REQUIREMENTS
Installation of this refrigeration appliance must be made in accordance with local codes. In the
absence of local codes, this unit should be installed in accordance with the National Electrical
Code and local codes.
This appliance must be electrically grounded in accordance with local codes or in the absence
of local codes with the National Electrical Code ANSI/NFPA 70, or Canadian Electrical code
CSA C22.1.
ozFridge Gas Fill Charge
Quantité de Gaz Réfrigerateur
Freezer Gas Fill Charge
Quantité de Gaz Congélateur
Total Absorbed Current
Courant Absorbée Totale
Voltage
Tension
Frequency
Frequence
Refrigerant Gas Type
Type de Gaz Rèfrigerant
MODEL
Made in Italy
CODE
SER.NO./N° SERIE
ETL LISTED
CONFORMS TO
ANSI/UL STD 250
CERTIFIED TO CAN/CSA
STD C22.2 NO.63
A
V
Hz
HESTAN COMMERCIAL CORP.
ANAHEIM, CA - USA
KRP36
7
0
1
115
60
R134a
FI24RC-RO
F20160725000001
©2019 Hestan Commercial Corporation
7
EN
GETTING TO KNOW YOUR APPLIANCE
FEATURES OF THE KRP / KRB REFRIGERATOR
1
8
9
10
11
12
13
14
2
3
4
5
6
8
9
10
11
12
13
14
2
3
4
5
6
1
KRP Models
KRB Models
7
7
Stainless steel grille,
aluminum trim
Control panel with display
Water Filter
Patented shelf positioning
system
“Low Temp” crisper
compartments
Automatic ice maker
Dual refrigeration system
Temperature display
Sound signals
Holiday function
Adjustable door shelves
LED lighting - multiple
locations in each compartment
Automatic drawer closing
system
FreshZone/freezer
compartment. When the
appliance is first turned on
the FreshZone/freezer
compartment is set to the
freezer mode. It can be
transformed into a
refrigerator or ExtendFresh
compartment.
2
3
4
5
6
7
8
9
10
11
12
13
14
1
Fresh Zone
Fridge
Low Temp
Low Temp
Fresh Zone
Fridge
©2019 Hestan Commercial Corporation
8
EN
GETTING TO KNOW YOUR APPLIANCE
(CONT.)
CONTROL PANEL (KRP / KRB MODELS)
The electronic control system on your Hestan refrigerator maintains constant temperature
in both compartments and displays the measured temperature on the control panel. It also
allows the user to personalize settings of the various functions and provides alerts should a
malfunction occur.
Switches the appliance (all compartments) between
ON and Stand by (Touch for three seconds).
Allows you to switch off the refrigerator
compartment (Touch for three seconds).
Allows access to the control panel menu to change
the appliance’s various settings.
Up/Down - refrigerator: Adjust refrigerator
temperature setting or to navigate through the
control panel menu.
Shows the temperature of the refrigerator and
freezer (FreshZone) compartments, the date and
time, control panel menu and visual messages.
Up/Down - freezer (FreshZone): Adjust freezer
(FreshZone) temperature setting or to navigate
through the control panel menu.
Tap to confirm selections made in the control panel
menu.
Tap to turn the ice maker on or off.
Flashes to signal user alerts such as door being left
open in combination with a warning tone. Tap this
key to deactivate the warning tone.
1
2
3
4
5
6
7
8
9
On/Off
Fridge
Menu
Up/Down
Fridge
Display
Up/Down
Freezer
(FreshZone)
Ok
Ice maker
Alarm
1 2 3 4 5 6 7 8 9
©2019 Hestan Commercial Corporation
9
EN
GETTING TO KNOW YOUR APPLIANCE
(CONT.)
FEATURES OF THE REFRIGERATOR OR FREEZER COLUMN (KRC/KFC)
KRC Models
KFC Models
7
8
9
10
2
3
6
4
1
7
9
3
5
8
1
2
6
10
11
1
2
3
4
5
6
7
8
9
10
11
Fridge
Low Temp
Freezer
Automatic door closing
system
LED lighting, multiple
locations
Stainless steel grille,
aluminum trim
Control panel with display
Patented shelf positioning
system
“Low Temp” crisper
compartments
Automatic ice maker
Refrigeration system
Temperature display
Sound signals
Adjustable door shelves
©2019 Hestan Commercial Corporation
10
EN
GETTING TO KNOW YOUR APPLIANCE
(CONT.)
CONTROL PANEL (KRC / KFC MODELS)
Switches the appliance between ON and Stand
by (Press for three seconds).
Allows access to the control panel menu to
change the appliance’s various settings.
Up/Down - Adjust the temperature setting or to
navigate through the control panel menu.
(KRC/KFC has only one temperature zone.)
Display: Shows the temperature of the
compartment, the date and time, control panel
menu and various other messages.*
Up/Down - Adjust the temperature setting or to
navigate through the control panel menu.
(KRC/KFC has only one temperature zone.)
Press to confirm selections made in the control
panel menu.
Flashes to signal user alerts such as door being
left open in combination with a warning tone.
Tap this key to deactivate the warning tone.
On/Off
Menu
Up/Down
Display
Up/Down
OK
Alarm
1 2 3 4 5 6 7
1
2
3
4
5
6
7
©2019 Hestan Commercial Corporation
11
EN
CONTROLS AND OPERATION
TURNING THE APPLIANCE ON AND OFF
FIRST STARTUP
When the appliance is connected to the electrical power supply but has not yet been switched
on, the display shows the message
.
This is a safety message to warn that the appliance is connected to the main power and the
control panel is off.
To switch the appliance on, press the On/Off button for three seconds.
SWITCHING OFF THE REFRIGERATOR AND FRESH ZONE COMPARTMENTS
When the appliance is first turned on the lower compartment is set to the “freezer” mode.
Once the appliance has started up, the freezer remains always on and can be switched off only
by switching off the complete appliance.
To power off, press On/Off
for three seconds.
RESTARTING
Use the same buttons to restart.
The freezer compartment always stays on and cannot be switched off except by completely
switching off the appliance by pressing the On/ Off
button for three seconds.
SWITCHING OFF FOR LONG PERIODS
During long absence periods it is recommended to switch off the refrigerator by pressing the
On/Off button for three seconds and disconnecting the electrical plug or the appropriate
circuit breaker.
Completely empty the refrigerator, clean and dry it and leave the door and drawer partially
open to prevent unpleasant odors.
If at the first startup the Standby message does not appear, but another message appears, it
means that the appliance has already started the cooling process.
If any alarms are sounding, touch the Alarm button to silence them, and let the appliance
run until the set temperature is reached.
During the first startup, it will not be possible to use the Menu to modify the factory settings
until the preset temperature has been reached.
Each time the appliance is switched on it goes through a self diagnosis procedure lasting three
minutes before completely starting up.
If only the refrigerator or wine compartment is turned off, the specific fan will continue to
operate to prevent the formation of unpleasant odors and mold.
Before turning off the appliance for a long period of time, remove all of the items inside and
leave the door and drawer open to prevent the formation of unpleasant odors and mold.
©2019 Hestan Commercial Corporation
12
EN
CONTROLS AND OPERATION
(CONT.)
ADJUSTING THE TEMPERATURE SETTINGS
Each model has been carefully tested before leaving the factory and is adjusted to ensure
high performance and low consumption. Usually, it is not necessary to modify the settings.
Nevertheless, according to special needs, it is possible to modify the set temperatures within a
certain range. The “recommended” settings below are also the factory presets for each of the
zones and modes.
To adjust the temperature use the Up/Down buttons
for that zone. Upon touching these
buttons the newly set temperature will appear in the display. To modify this temperature, use
the buttons until reaching the desired temperature. After several seconds of showing the new
set temperature, the display will resume showing actual temperature.
Refrigeration Compartment
and FreshZone/Freezer
drawer set as refrigeration
From 34°F to 46°F [+1°C to +7°C], the recommended
temperature setting is 39°F [+4°C].
FreshZone/Freezer drawer
set as ExtendFresh
28°F to 36°F [−2°C to +2°C]
Recommended temperature setting is 32°F [
0°C]
Freezer Compartment and
FreshZone/Freezer drawer
set as freezer
From 9°F to −11°F [−13°C to −23°C], the recommended
temperature setting is
0°F [−18°C].
The actual temperature can vary from the set temperature following frequent openings of the
doors or insertion of room temperature foods or large quantities of foods.
6 to 12 hours may be necessary to reach the selected temperature.
ACTIVATING THE ICE MAKER
Do not perform a Manual Clean or activate the Ice Maker until the water
line is properly connected and water is turned on to the appliance.
KRB/KRP: The Ice Maker button
located on the main control panel turns the automatic ice
maker ON/OFF. The button is illuminated when the ice maker is functioning.
Other Models: The ice maker is activated or deactivated using the menus:
An initial flush of the water circuit should be performed before
activating the Ice Maker for the first time. This is done using the Manual
Clean function as follows.
Touch the
button to activate the interactive menu.
The active menu item is shown at the bottom of the display. If “Functions” isn’t showing, use
the Up/Down
buttons to show the various choices until “Functions” is shown.
In the instruction below, when the symbol is shown, that means “use the Up/Down
button to display the following item”.
See “WATER FILTER MANAGEMENT” on page 18 for more information.
OK
OK
OKOK
OK
OK
OKOK
Turn icemaker ON
Turn icemaker OFF
OK
OK
OKOK
©2019 Hestan Commercial Corporation
13
EN
SPECIAL SETTINGS AND FUNCTIONS
The appliance can be configured to suit various needs through its settings, such as its operating
modes, display language, and information display. Special functions are provided to meet
various short term needs, such as parties or vacations.
The Settings and Functions are accessed on the main display by pressing the
button.
The Up/Down buttons display options which can be selected by pressing the button. The
Up/Down buttons
scroll through the selected function or setting sub-menus if applicable,
activating or deactivating by pressing the button.
Once a setting or function is confirmed, the display will automatically step back to the previous
menu to allow selection of other functions. In many cases it is possible to return to the
previous selection through the
button.
The language of the messages appearing on the display can be changed by operating as follows:
Enter the Menu by pressing the
button, select Settings via the Up/Down buttons and
confirm via . Then select the Language function and the desired language.
See also: “USING THE CONTROL MENUS” on page 5.
UNLOCKING THE KEYPAD
The keypad automatically locks after a while if not being
used. When it is locked, any touch of the keypad will display
“KEYPAD LOCKED’.
To unlock, touch the
key and Down key together
for several seconds, until the message “KEYPAD
UNLOCKED” shows on the display.
CONTROLS AND OPERATION
(CONT.)
DISPLAY INFORMATION AND MALFUNCTION MESSAGES
An integrated control system provides information through light signals or text messages
visualized on the display.
The information signal is always visualized with a steady text message, while a malfunction
signal is visualized with blinking text. The sound signal that accompanies some malfunction
signals can be deactivated by pressing the Alarm button on the main control panel.
The list of malfunction signals is located at the back of this manual.
©2019 Hestan Commercial Corporation
14
EN
FUNCTIONS
MAX COOL
The Max Cool Mode prepares the cooling, Fridge and FreshZone compartments for the
introduction of fresh food or other items which may have warmed during transport. The more
quickly an item can be cooled or frozen the better it will be preserved.
This mode can also be effective at maintaining compartment temperatures while entertaining
when higher than average door and drawer openings are anticipated.
To use special functions, select the
button and use the Up/Down buttons .
The Max Cool function lowers the refrigerator temperature to 35.6°F [+2°C] for 12 hours,
permitting more rapid cooling of food that has just been placed in. Once the 12 hours have
expired, the function deactivates automatically, returning to the previously set temperature.
You can set a 1-12 hour delay before the function starts. If a power outage occurs while
MaxCool is active, the appliance resumes normal operation when power returns.
MAX COOL FRESHZONE
This function should be activated at least 24 hours before inserting room temperature items
into the freezer, or several hours before placing into the freezer previously frozen items which
have been subject to a slight temperature rise. When activated, the appliance will operate in
MaxCool for 56 hours and then return to usual operation. You can set the function to start
after a delay of 1-12 hours. If a power outage occurs while MaxCool is active, the appliance
resumes normal operation when power returns.
HOLIDAY
This function (recommended in case of prolonged absences since it allows considerable energy
savings) brings the refrigerator compartment temperature to 57.2°F [+14°C]. It is possible
to program the duration, or it can be manually deactivated upon returning after a period of
absence. This function remains active even if during the period of absence there is a prolonged
interruption of electrical power. It is possible to program a period from 1 to 90 days.
Max Cool
Max Cool
Max Cool
Max Cool
Max Cool
Max Cool
Max Cool
HHooww ttoo aaccttiivvaattee
HHooww ttoo ddeeaaccttiivvaattee
Setting a delayed
start
Max Cool
FreshZone
Max Cool
Max Cool
FreshZone
Max Cool
FreshZone
Max Cool
Max Cool
FreshZone
Max Cool
FreshZone
Max Cool
FreshZone
HHooww ttoo aaccttiivvaattee
HHooww ttoo ddeeaaccttiivvaattee
Setting a delayed
start
CONTROLS AND OPERATION
(CONT.)
©2019 Hestan Commercial Corporation
15
EN
CONTROLS AND OPERATION
(CONT.)
HOLIDAY FRESHZONE
It is possible to program the function with a delay of 1 to 12 hours, and a duration of 1 to 90
days. This function (recommended in case of prolonged absences since it allows considerable
energy savings) brings the FreshZone/freezer compartment temperature to 46.4°F [8°C]. It is
possible to program the duration, or it can be manually deactivated upon reentry after a period
of absence.
This function remains active even if during the period of absence there is a prolonged
interruption of electrical power.
BEVERAGE COOLER
This function can be activated when it is necessary to cool off beverages quickly, by placing
them inside the freezer compartment.
It is possible to select a duration of 1 to 45 minutes. A sound signal will indicate when the
optimal temperature has been reached. After removing the beverages, deactivate the sound
signal by pressing the Alarm button.
Holiday
Holiday
Holiday
Holiday
Holiday
Holiday
Holiday
Holiday
HHooww ttoo aaccttiivvaattee
HHooww ttoo ddeeaaccttiivvaattee
uuppoonn rreettuurrnn
HHooww ttoo pprrooggrraamm
tthhee dduurraattiioonn
Holiday Holiday
Holiday
Holiday
Holiday
HolidayHoliday
Holiday
FreshZone
FreshZone
FreshZone
FreshZone
FreshZone
HHooww ttoo aaccttiivvaattee
HHooww ttoo ddeeaaccttiivvaattee
uuppoonn rreettuurrnn
HHooww ttoo pprrooggrraamm
tthhee dduurraattiioonn
How to
deactivate
How to program
the duration
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
Beverage
BeverageBeverage
Beverage
Beverage
Beverage
Beverage
©2019 Hestan Commercial Corporation
16
EN
CONTROLS AND OPERATION
(CONT.)
ICE MAKER ON/OFF
Certain models do not have the (Ice Maker) button on the control panel, and the ice maker
may be turned ON/OFF using menu functions.
ICE MAKER SETTINGS
The Ice Maker function permits selecting the size of the ice cubes, by choosing between Large
(base setting) or Medium, and activation of the Fast Ice function, which increases the quantity
of produced ice. The Fast Ice function deactivates automatically after 24 hours.
SABBATH MODE
The function makes it possible to comply to certain religious observances requiring that the
operation of the appliance is not affected by the opening or closing of the doors (the
thermostatic control, the inner lighting and the ice maker are deactivated).
When you activate Sabbath Mode, the interior lights will deactivate, and the display will show
“Sabbath Mode ON”. When you turn Sabbath Mode off, the appliance will return to normal
operation, except that menus will not be available for several minutes.
OK
OK
OKOK
OK
OK
OKOK
Turn icemaker ON
Turn icemaker OFF
OK
OKOK
OK
OKOK
OK
OK
OK
OK
OK OK
OK
OK
OK
OK
OK
Fast Ice Fast Ice
Fast Ice
Fast Ice
How to set cube
size to large
HHooww ttoo aaccttiivvaattee tthhee
FFaasstt IIccee ffuunnccttiioonn
HHooww ttoo ddeeaaccttiivvaattee
FFaasstt IIccee
OK
How to set cube
size to medium
OK
OK
OK
OK
OK
OK
OK
OK
OK
OK
HHooww ttoo aaccttiivvaattee
HHooww ttoo ddeeaaccttiivvaattee
©2019 Hestan Commercial Corporation
17
EN
CONTROLS AND OPERATION
(CONT.)
WATER FILTER MANAGEMENT
The following functions display filter life, permit bypassing the filter, and provide manual
flush/clean of the filter and ice maker.
Filter Status and counter reset
Functions to view remaining life and to reset counter after changing filter cartridge.
Bypassing the filter
The included filter can be bypassed when excellent quality water is available from he home
water system.
Manual clean (flush) water filter
If ice production has been disabled or unused for a long period it is recommended to perform a
Manual Clean function to flush out water which has sat in the system during this period.
Repeat the operation until the water is clean. Before proceeding it is important to turn off the
ice maker by pressing the
button or using the menu. (See previous page.)
Correctly position the ice tray or another suitable container under the ice maker to collect
water, then close the drawer. At the end of the operation, wash the tray.
OK
View Status
Resetting filter
How to set the filtered
water meter to zero
How to check the
status of the filter
The View Status function displays the remaining life of the filter.
The Reset Filter function sets the filter usage counter to zero.
Do this when replacing the filter cartridge.
How to activate
How to de-activate
filter bypass
filter bypass
How to manually
clean the filter
©2019 Hestan Commercial Corporation
18
EN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76

GE KRCR24 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

dans d''autres langues