Amana NED5800HW Le manuel du propriétaire

Marque: Amana

Modèle: NED5800HW

Catégorie: Sèche-linge

Taper: Le manuel du propriétaire

Ce manuel convient également à

NGD5800HW

W11184584A

If you have any problems or questions, visit us at www.amana.com

Pour tout problème ou question, consulter www.amana.com

Use and Care Guide

Guide d’utilisation et d’entretien

Electronic Dryer

Sécheuse électronique

Para obtener acceso

al Manual de uso y

cuidado en español, o para

obtener información adicional

acerca de su producto, visite:

www.amana.com.

DRYER SAFETY

TABLE OF CONTENTS

DRYER SAFETY .......................................................................2

ACCESSORIES ........................................................................4

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW ............5

CONTROL PANEL AND FEATURES ......................................... 6

CYCLE GUIDE .......................................................................... 8

USING YOUR DRYER ............................................................10

ADDITIONAL FEATURES .......................................................12

DRYER CARE .........................................................................12

TROUBLESHOOTING ............................................................14

WARRANTY ............................................................................ 17

ASSISTANCE OR SERVICE ..................................... Back Cover

TABLE DE MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE ...............................................18

ACCESSOIRES ......................................................................20

VÉRIFICATION D’UNE CIRCULATION D’AIR ADÉQUATE

POUR LE SYSTÈME D’ÉVACUATION ....................................21

TABLEAU DE COMMANDE ET CARACTÉRISTIQUES ..........22

GUIDE DE PROGRAMMES ....................................................24

UTILISATION DE LA SÉCHEUSE ...........................................27

CARACTÉRISTIQUES SUPPLÉMENTAIRES ..........................29

ENTRETIEN DE LA SÉCHEUSE .............................................30

DÉPANNAGE ..........................................................................32

GARANTIE .............................................................................. 35

ASSISTANCE OU SERVICE ...........................Couverture arrière

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this

or any other appliance.

–

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the re department.

–

Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

•

Clear the room, building, or area of all occupants.

ACCESSORIES

15" Pedestal

Color-matched pedestals raise the washer

and dryer to a more comfortable working

height. The large drawer provides convenient

storage.

Stack Kit

If space is at a premium, the stack kit allows

the dryer to be installed on top of the washer.

Drying Rack

The Drying Rack provides a

stationary drying surface for

items such as sweaters and tennis

shoes. See the “Additional Features”

section for more information.

Customize your new washer and dryer with the following

genuine Whirlpool accessories. For more information on

options and ordering, call 1-800-442-9991, or visit us at:

www.amana.com/help.

In Canada, call 1-800-807-6777 or visit us at:

www.amana.com/help

INSTALLATION & MAINTENANCE

ACCESSORIES

FACTORY CERTIFIED PARTS – these three

words represent quality parts and accessories

designed specically for your appliance.

Time tested engineering that meets

our strict quality specications.

FACTORY CERTIFIED PARTS

Accessories designed for your appliance:

CHECK YOUR VENT SYSTEM FOR GOOD AIRFLOW

Good airow

Along with heat, dryers require good airow to efciently

dry laundry. Proper venting will reduce your drying times

and improve your energy savings. See Installation

Instructions.

The venting system attached to the dryer plays a big role

in good airow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Maintaining good airow

Clean your lint screen before each load.

Replace plastic or foil vent material

with 4" (102 mm) diameter heavy, rigid

vent material.

Good

Better

Use the shortest length of vent possible.

Use no more than four 90° elbows in a vent system.

Each bend and curve reduces airow.

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete, be

sure to follow the Installation Instructions supplied with

your dryer for nal product check.

Clear away items from the front of the dryer.

Eco Dry option

The Eco Dry option will default on only for the Normal cycle and is only available on that cycle.

This option allows you to increase your energy savings by using a slightly lower heat level. The Eco Dry option will increase

drying times by approximately 40 minutes, which will be reected on the LED Display. If optimal time is desired, touch ECO DRY

to turn off this option.

Use Sensor Cycles for better fabric care and energy savings

Use the Sensor Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Sensor Cycles, drying

air temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off

when the load reaches the selected dryness. Use the Normal dryness level to provide optimal energy savings.

With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to overdrying.

Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.

CONTROL PANEL AND FEATURES

POWER

Touch to turn the dryer on and off. Touch to stop/cancel

a cycle at any time.

CYCLES

Touch a button for the desired drying cycle. See “Cycle

Guide” for cycle details.

START/PAUSE

Touch and hold until LED counts down “3-2-1” and the

dryer starts; then let go to start a cycle, or touch once

while a cycle is in process to pause it.

MODIFIERS

Use to select available modiers for your dryer. Not all

cycles and options are available on all models.

Temp

When using Timed Dry/Quick Cycle, you may select

a dry temperature based on the type of load you are

drying. Use the warmest setting that is safe for the

garments in the load. Follow garment label instructions.

Dryness

You may adjust the Dryness on Sensor cycles (except

for the Sanitize cycle), if desired.

NOTE: Dryness is for use with Sensor cycles only.

More Time/Less Time Timed Dry Adjust

Touch MORE TIME or LESS TIME with the Timed Dry/

Quick cycle to increase or decrease the length of the

cycle.

OPTIONS

Use to select available options for your dryer. Not all cycles

and options are available on all models.

Wrinkle Prevent

Option

If you will be unable to remove a load immediately,

touch WRINKLE PREVENT to add up to 150 minutes

of periodic tumbling to help reduce wrinkling.

NOTE: If you open the dryer door prior to the end

of the Wrinkle Prevent option, the dryer will go into

standby.

Cycle Signal

Use this option to turn the signal indicating the end

of a drying cycle to low, medium, high, or off. The

volume you select here will also be applied to the

Damp Dry Signal.

Not all features and cycles are available on all models.

NOTE: You may also turn off the tones that sound

when a feature, setting, or option is touched. Touch

and hold CYCLE SIGNAL for about 3 seconds to turn

sounds to low, medium, high, or off.

Damp Dry Signal

Touch to turn the Damp Dry Signal on or off. When

selected, a series of beeps will sound when the load

is damp, but not completely dry. This will allow you to

take clothes out of the load that do not need to dry

completely. This option is available on some cycles.

The Damp Dry signal is selected as a default for the

Bulky Items/Normal, Bulky Items/Wrinkle Control,

and Bulky Items/Heavy Duty cycles, as a reminder

to manually reposition bulky loads midway through

the cycle.

Control Lock

Use this option to lock the controls of the dryer

and avoid an accidental change in cycle options

or preferences during a drying cycle.

Touch and hold CONTROL LOCK for 3 seconds to

lock or unlock the controls of the dryer. During this

time, the LED Display will count down “3-2-1.”

Once the controls are locked, the LED Display

will display “Loc.”

NOTE: The Control Lock function may be enabled

when recovering from a power failure. To unlock the

control, touch and hold CONTROL LOCK for at least

3 seconds.

Eco Dry

Option

The Eco Dry option will default on only for the Normal

cycle and is only available on that cycle. This option

allows you to increase your energy savings by using

a slightly lower heat level. The Eco Dry option will

increase drying times by approximately 40 minutes,

which will be reected on the LED Display. If optimal

time is desired, touch ECO DRY to turn off this option.

LED DISPLAY

When you select a cycle, its default settings will light up

and the Estimated Time Remaining (for Automatic Cycles)

will vary depending on the cycle selection, or actual time

remaining for Timed Dry cycles (for Manual Cycles) will be

displayed.

NOTE: The control panel features a sensitive surface that responds to a light touch of your nger. To ensure your selections are

registered, touch the control panel with your ngertip, not your ngernail. When selecting a setting or option, simply touch the

appropriate button.

3 6

CYCLE STATUS INDICATORS

The Cycle Status Indicators show the progress of a cycle.

Not all indicators are available on all models.

Sensing

The Sensing indicator will light periodically during Sensor

Cycles to indicate that the moisture sensor on the dryer is

operating. This indicator will not light during Timed Cycles

or options such as Wrinkle Prevent.

Wet

The load is still wet and/or the cycle just started.

Damp

This indicator shows that the load is partially dried and

items that you may wish to hang up or iron while still damp

may be removed.

Cool Down

The dryer has nished drying with heat and is now

tumbling the load without heat to cool it down.

Check Vent

The Check Vent indicator is a feature available for

Automatic cycles only. This indicator will show the status

of airow through the dryer and the dryer vent system

for the dryer’s life. During the sensing phase at the

beginning of the cycle, the Check Vent light will come on

if a blocked vent or low airow issue is detected. This light

will stay on for the entire cycle. Should the Check Vent

light illuminate, refer to the “Troubleshooting” section for

potential solutions to the issue.

The light will be cleared upon completion of the cycle,

touching Power, or opening the door. The Check Vent light

will continue to illuminate during the cycle unless the root

cause is resolved.

REMEMBER: The dryer will continue to operate even

while the indicator is lit, but poor airow can impact dry

times and overall performance. For more information on

maintaining good airow, see “Check Your Vent System

for Good Airow.”

NOTE: If there are other error issues during a cycle,

the Check Vent indicator will not light up. See the

“Troubleshooting” section.

End

This will indicate that the selected cycle has ended

and the load may be removed from the dryer. If Wrinkle

Prevent has been selected, the dryer may continue to

tumble the load, even if “End” is displayed.

Control Lock

This will illuminate once the controls are locked.

CYCLE GUIDE — SENSOR CYCLES

Settings and options shown in bold are default settings for that cycle.

If settings are changed, the new settings will be remembered. If there is a power failure, settings will return to the default.

Not all features and cycles are available on all models.

Not all settings and options are available on each cycle.

Load Size Recommendations

For best results, follow the wet load size recommendations

noted for each cycle.

Small load: Fill the dryer drum with 3–4 items, not more

than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not tightly pack. Items need to tumble freely.

Use Sensor Cycles for better fabric care and energy savings

The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Use the Normal dryness level to provide optimal energy savings.

Items to dry: Cycle:

Drying

Temperature:

Dryness

Level:

Default

Time:

Available

Options: Cycle Details:

Shirts, blouses,

permanent

press, synthetics,

lightweight items

Regular High

Medium

Low

Air

Normal

Less

48 Wrinkle Prevent

Cycle Signal

Uses Medium heat to dry large loads

of mixed fabrics and items.

Work clothes,

casual wear,

mixed cottons,

sheets, corduroys

Normal High

Medium

Low

Air

Normal

Less

1:25 Wrinkle Prevent

Cycle Signal

Eco Dry

Uses Medium heat to dry large loads

of mixed fabrics and items. Normal

is the most efcient cycle.

Undergarments,

blouses, lingerie,

performance wear

Delicates High

Medium

Low

Air

Normal

Less

28 Wrinkle Prevent

Cycle Signal

Uses Low heat to gently dry delicate

items.

Shirts, blouses,

permanent

press, synthetics,

lightweight items

Wrinkle

Control

High

Medium

Low

Air

Normal

Less

35 Wrinkle

Prevent

Cycle Signal

Uses a stepped drying temperature

from Medium to Low for improved

moisture removal and enhanced

fabric care.

Jackets,

comforters,

pillows

Bulky Items High

Medium

Low

Air

Normal

Less

52 Wrinkle Prevent

Cycle Signal

Use for drying large, bulky items; do

not overll dryer drum. Partway through

the cycle, the signal will sound for 2

minutes to indicate when it is time to

rearrange items for optimal drying.

Heavyweight

items such as

towels or heavy

work clothes

Heavy Duty High

Medium

Low

Air

Normal

Less

57 Wrinkle Prevent

Cycle Signal

Offers stepped drying starting with

High heat followed by Medium heat

for enhanced fabric care and energy

savings.

White, sturdy

items

Whites High

Medium

Low

Air

Normal

Less

45 Wrinkle Prevent

Cycle Signal

Uses High heat to dry large loads

of white, sturdy fabrics and items.

Large loads of

heavyweight items

Sanitize High More 1:30 Wrinkle Prevent This is a long cycle with high heat,

which has been proven to reduce

household bacteria. This cycle is not

recommended for all fabrics. Use for

large loads of heavyweight fabrics.

Bright or darkly

colored cottons,

linens, casual and

mixed loads

Colors High

Medium

Low

Air

Normal

Less

53 Wrinkle Prevent

Cycle Signal

Uses Medium heat to gently dry bright

or darkly colored items.

Large loads of

cotton towels,

heavyweight items

Towels High

Medium

Low

Air

Normal

Less

1:00 Wrinkle Prevent

Cycle Signal

This is a long cycle with high heat,

which has been proven to reduce

household bacteria. This cycle is not

recommended for all fabrics. Use for

large loads of heavyweight fabrics.

Items to dry: Cycle:

Drying

Temperature:

Default

Time:

Available

Options: Cycle Details:

Any load

NOTE: Select Air

to dry foam,

rubber, plastic,

or heat-sensitive

fabrics.

Timed Dry High

Medium

Low

Air

40 Wrinkle Prevent Use to dry items to a damp level for items that do

not require an entire drying cycle. Select a drying

temperature based on the type of fabrics in your load.

If you are unsure of the temperature to select for a

load, select the lower setting rather than the higher

setting.

Small loads

and sportswear

Quick High

Medium

Low

Air

15 Wrinkle Prevent For small loads of 3–4 items.

CYCLE GUIDE — TIMED CYCLES

Settings and options shown in bold are default settings for that cycle.

If settings are changed, the new settings will be remembered (except on Quick). If there is a power failure, settings will return

to the default.

Not all features and cycles are available on all models.

Not all settings and options are available on each cycle.

Load Size Recommendations

For best results, follow the load size recommendations noted

for each cycle.

Small load: Fill the dryer drum with 3–4 items, not more

than 1/4 full.

Medium load: Fill the dryer drum up to about 1/2 full.

Large load: Fill the dryer drum up to about 3/4 full.

Do not overload. Items need to tumble freely.

Adjusting drying time on Timed Cycles

When you select a Timed Cycle, the time

appears in the display. Use More Time

and Less Time to increase or decrease

the time in 5-minute increments.

The maximum dry time is 150 minutes.

Selecting the Drying Temperature

A High heat setting may be used for drying heavyweight items

such as towels and work clothes.

A Low to Medium heat setting may be used for drying

mediumweight items such as sheets, blouses, dresses,

underwear, permanent press fabrics, and some knits.

Use a no heat (air) setting for foam, rubber, plastic,

or heat-sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures

for various loads, refer to the care label directions.

NOTE: Government energy certications for this model were based on the Normal Cycle, Highest Temperature Setting, Normal

Dryness Level, Eco Dry On. The as-shipped defaults were the same as the Government Energy Certication Settings except the

default Temperature Setting of Medium was adjusted to the Highest Temperature Setting.

Touch POWER

Touch POWER to turn on the dryer.

USING YOUR DRYER

Clean the lint screen

Clean the lint screen before each load. Pull the lint screen

straight up. Roll lint off the screen with your ngers. Do

not rinse or wash screen to remove lint. Wet lint is hard

to remove. Push the lint screen rmly back into place.

For additional cleaning information, see “Dryer Care.”

Load the dryer

Open the door by pulling on the handle. Place laundry in the

dryer. Add a dryer sheet to wet load, if desired. Close the door.

IMPORTANT: Do not tightly pack the dryer. Items need

to tumble freely. Tightly packing can lead to poor drying

performance and may increase wrinkling and tangling.

WARNING: To reduce the risk of re, electric shock, or injury

to persons, read the Important Safety Instructions before

operating this appliance.

Select desired cycle

Select the desired cycle for your load. See the “Cycle Guide”

for more information about each cycle.

Touch and hold START/PAUSE

to begin cycle

To begin the cycle, touch and hold START/PAUSE until the

display counts down “3-2-1” and the dryer starts.

8. Remove garments promptly

after cycle is nished

Promptly remove garments after cycle has completed

to reduce wrinkling. If you will be unable to remove the load

promptly, select the Wrinkle Prevent option.

Adjust cycle modiers, if desired

You may adjust different settings,

depending on whether you have selected

a Sensor Cycle or Timed Cycle. See the

“Cycle Guide” for detailed information.

NOTE: Not all options and settings are available with all cycles.

Not all cycles are on all models.

Sensor Cycles:

The temperature may be changed by touching Temp until

the desired dry temperature is lit. Once a cycle has started,

the temperature can be changed during the rst 5–8 minutes

of the cycle.

You can select a different dryness level, depending on

your load. Touch DRYNESS to scroll from Less to More to

automatically adjust the dryness level at which the dryer will

shut off. Once a dryness level is set, it can be changed during

the rst 5–8 minutes of the cycle.

Sensor cycles give the best drying in the shortest time.

Drying time varies based on fabric type, load size, and dryness

setting. Drying time is estimated and may change throughout

the cycle. Drying time cannot be changed on Sensor Cycles.

Timed Cycles:

When you select a Timed Cycle, the time appears in the

display. Touch MORE TIME or LESS TIME to increase or

decrease the time in 5-minute increments.

The temperature may be changed by touching Temp until

the desired dry temperature is lit. The temperature cannot

be changed if the temperature is started with Air.

Select any additional options

Add additional options such as Wrinkle Prevent and/or Eco

Dry by touching that option. If you will be unable to remove

the load promptly, select Wrinkle Prevent before touching

Start/Pause.

NOTE: Not all options and settings are available with all

cycles.

ADDITIONAL FEATURES

2. Align the two hooks on the front of the drying rack with

the holes in the dryer door opening and press down fully

into holes. Rest the rear support on the dryer back ledge.

USING THE DRYING RACK

To purchase a drying rack for your dryer, see “Accessories”

for more information. You will need your model and serial

number and the purchase date. Remove and discard any

packing material before use.

Use the drying rack for items that you do not want to tumble

dry, such as sweaters and tennis shoes. When you use the

drying rack, the drum continues to turn, but the rack remains

stationary.

The drying rack is intended for use with the Timed Dry cycle

only. The drying rack cannot be used with Sensor Cycles.

To use the drying rack:

IMPORTANT: Do not remove the lint screen.

1. Open dryer door.

3. Place wet items on top of the drying rack. Allow space

around items for air to circulate. The drying rack does

not move, but the drum will rotate; be sure to leave

adequate clearance between items and the inside

of the dryer drum. Make sure items do not hang

over the edges or between drying rack grille.

4. Close the door.

5. Select a Timed Dry cycle. Items containing foam, rubber,

or plastic must be dried on a clothesline or by using the

Air setting.

6. When the cycle is selected, the display shows the

default time. You can change the actual time in the cycle

by increasing or decreasing the cycle time.

7. Start the dryer.

NOTE: Check the lint screen and remove any lint

accumulated from items dried on the drying rack

after the cycle is nished.

DRYER CARE

CLEANING THE DRYER LOCATION

Keep dryer area clear and free from items that would

block the airow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

CLEANING THE DRYER INTERIOR

To clean dryer drum:

1. Use a mild hand dish detergent mixed at a low

concentration with very warm water, and rub with

a soft cloth.

2. Rinse well with a wet sponge or towel.

3. Tumble a load of clean clothes or towels to dry drum

Use a microber cloth and hot water in a spray bottle

to clean the drum and a second microber towel to dry.

NOTE: Garments that contain unstable dyes, such as

denim blue jeans or brightly colored cotton items, may

discolor the rear of the dryer interior. These stains are not

harmful to your dryer and will not stain future loads of

clothes. Dry unstable dye items inside out to avoid transfer

of dye.

REMOVING ACCUMULATED LINT

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a qualied appliance servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

CLEANING THE LINT SCREEN

Every load cleaning

The lint screen is located in the door opening of the dryer.

Clean the lint screen before each load. A screen blocked

by lint can increase drying time.

To clean:

1. Pull the lint screen straight up. Roll lint off the screen

with your ngers. Do not rinse or wash screen to remove

lint. Wet lint is hard to remove.

2. Push the lint screen rmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements” in the Installation Instructions.

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

AS-NEEDED CLEANING

NON-USE, STORAGE, AND MOVING CARE

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Gas models only: Close shut-off valve in gas supply line.

3. Gas models only: Disconnect gas supply line pipe and

remove ttings attached to dryer pipe.

4. Gas models only: Cap the open gas supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

For direct-wired dryers:

1. Disconnect power.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the Installation Instructions to locate, level, and

connect the dryer.

TROUBLESHOOTING

If you experience Possible Causes Solution

Dryer Operation

Dryer will not run Door not closed completely. Make sure the dryer door is closed completely.

Start/Pause touched with ngernail. Touch START/PAUSE with pad of nger.

Household fuse is blown or circuit

breaker has tripped.

There may be two household fuses or circuit breakers for the

dryer. Check that both fuses are intact and tight, or that both

circuit breakers have not tripped. Replace the fuses or reset

the circuit breaker. If the problem continues, call an electrician.

Incorrect power supply. Electric dryers require 240 volt power supply. Check with a

qualied electrician.

Wrong type of fuse. Use a time-delay fuse.

Dryer will not turn off Dryer door was opened prior to the

end of the Wrinkle Prevent option.

If you open the dryer door prior to the end of the Wrinkle Prevent

option, the dryer will go into the Pause mode. You will need to

touch Power to turn off or touch Start/Pause to continue the

Wrinkle Prevent option.

Dryer will not heat Household fuse is blown or circuit

breaker has tripped.

The drum may be turning, but you may not have heat. Electric

dryers use two household fuses or circuit breakers. Replace the

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Incorrect power supply. Electric dryers require 240 volt power supply. Check with a

qualied electrician.

Supply line valve not open. For gas dryers, make sure that the valve on the gas supply line

is open.

Unusual Noise

Thumping noise Dryer hasn’t been used in a while. This is normal. The thumping sound should diminish after a few

minutes of use.

Rattling or vibrating noise A small object caught between the

edges of dryer drum.

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

Dryer isn’t properly leveled. The dryer may vibrate if not properly installed. See the

Installation Instructions. All four dryer feet should be in rm

contact with the oor.

Clothing is balled up in dryer. When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Clicking noise Gas valve operating. On gas dryers, you may hear the gas valve clicking as it opens

and closes. This is normal.

Dryer Results

Drying times are too

long and clothes are

not getting dry

Lint screen is clogged with lint. Clean lint screen before each load.

Eco Dry option is on. For optimal dry times, turn off the Eco Dry option.

The exhaust vent or outside exhaust

hood is clogged with lint, restricting

air movement.

Run the dryer for 5–10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not feel

air movement, clean exhaust system of lint or replace exhaust

vent with heavy metal or exible metal vent. See the Installation

Instructions.

The exhaust vent is not the correct

length.

Check that the exhaust vent is not too long or has too

many turns. Long venting will increase drying times.

See the Installation Instructions.

The exhaust vent diameter is not the

correct size.

Use 4" (102 mm) diameter vent material.

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Dryer Results (cont.)

Drying times are too

long and clothes are not

getting dry (cont.)

The dryer is not level. Clothes not contacting the moisture sensors during Sensor

cycles. See “Level Dryer” in the Installation Instructions.

The load is too large and heavy to dry

quickly.

Separate the load to tumble freely.

Fabric softener sheets are blocking

the grille.

The air outlet grille is just inside the door, behind the lint screen.

Check that it is not blocked by a fabric softener sheet.

Use only one fabric softener sheet, and use it only once.

The dryer is located in a room with

temperature below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

The dryer is located in a closet. Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum of

1" (25 mm) of airspace, and, for most installations, the rear of the

dryer requires 5" (127 mm). See the Installation Instructions.

Cycle time is too short The load may not be contacting the

sensor strips on Sensor cycles.

Level the dryer. See the Installation Instructions. All four dryer

feet should be in rm contact with the oor.

The Sensor cycle is ending early. Change the dryness level setting on Sensor Cycles. Increasing

or decreasing the dryness level will change the amount of drying

time in a cycle.

Lint on load Lint screen is clogged with lint. Clean lint screen before each load.

Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain

your garments.

Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue jeans).

These will not transfer to other clothing.

Loads are wrinkled The load was not removed from dryer

at the end of the cycle.

NOTE: Refer to garment care label instructions. Dry-clean-only

garments are not recommended.

The dryer was tightly packed. Dry smaller loads that can tumble freely. Results may also vary

depending on fabric type.

Odors Recent painting, staining, or

varnishing in the area where your

dryer is located.

Ventilate the area. When the odors or fumes are gone from the

area, rewash and dry the clothing.

The electric dryer is being used for

the rst time.

The new electric heating element may have an odor.

The odor will be gone after the rst cycle.

Load too hot Load removed before cooldown

portion of cycle complete.

Allow the dryer to complete the cooldown portion of the cycle

before removing the load.

Using Timed Dry cycle with a high

temperature setting.

Select a Sensor cycle with a lower heat setting to avoid

overdrying the load.

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

TROUBLESHOOTING

If you experience Possible Causes Solution

Dryer Displaying Code Message or Indicator Is Lit

“PF” (power failure) The drying cycle has been interrupted

by a power failure.

Touch and hold START/PAUSE to restart the dryer cycle or touch

POWER to clear the display.

“L2” Diagnostic Code

(low or no line voltage

condition)

There may be a problem with your

home power supply, keeping the

dryer’s heater from turning on.

The dryer will continue to run when this diagnostic code is

present. Touch any pad to clear the code from the display and

return to the estimated time remaining.

NOTE: This error will only show during the initial installation.

Try the following:

•

Check to see if a household fuse has blown or circuit breaker

has tripped. Electric dryers use two household fuses or

breakers. Replace the fuse or reset the circuit breaker.

•

Conrm that the power cord is properly installed. Refer to

the Installation Instructions for details.

•

Select a Timed Dry heated cycle, and restart the dryer.

If the message persists, consult a qualied electrician.

“F# E#” (F1 E1, F3 E1,

etc.) variable service

codes

The dryer is in need of service. If a code beginning with an “F” appears in the display, alternating

between F# and E#, the dryer control has detected a problem

that requires service. Call for service.

Check Vent indicator is lit The lint screen or vent is clogged;

the vent is crushed or kinked or has

too many turns.

The dryer will continue to run when this indicator is lit. Try the

following:

• Clean lint screen.

• Check to see if the vent run from the dryer to the wall is

crushed or kinked.

• Conrm that the vent run from the dryer to the wall is free of

lint and debris.

• Conrm that the exterior vent exhaust hood is free of lint and

debris.

• Conrm that your vent system falls within the recommended

run length and number of elbows for the type of vent you

are using. Refer to “Plan Vent System” in the Installation

Instructions for details.

• Select a Timed Dry heated cycle, and restart the dryer.

• If the indicator remains lit, have your entire home venting

run cleaned.

“Loc” The Control Lock is enabled. Touch and hold CONTROL LOCK for 3 seconds to unlock the

controls of the dryer. During this time, the LED Display will count

down “3-2-1.” When the Control Lock is disabled, the LED

Display will clear.

First try the solutions suggested here or visit our website at www.amana.com/owners

for assistance and to possibly avoid a service call.

WHIRLPOOL CORPORATION LAUNDRY WARRANTY

LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is installed, operated, and maintained according to instructions

attached to or furnished with the product, Amana, Admiral, Estate, Inglis, or Roper brands of Whirlpool Corporation or Whirlpool

Canada LP (hereafter “Whirlpool”) will pay for Factory Specied Replacement Parts and repair labor to correct defects in materials or

workmanship that existed when this major appliance was purchased.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. Service must be provided by a company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brand

appliances. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in

the country in which it was purchased. This limited warranty is effective from the date of original consumer purchase. Proof of original

purchase date is required to obtain service under this limited warranty.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is

used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or

repair house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air lters, or water lters. Consumable parts are excluded from warranty

coverage.

4. Damage resulting from accident, alteration, misuse, abuse, re, ood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Cosmetic damage, including scratches, dents, chips or other damage to the nish of your major appliance, unless such damage

results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.

6. Pick up and delivery. This major appliance is intended to be repaired in your home.

7. Repairs to parts or systems resulting from unauthorized modications made to the appliance.

8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an

authorized company designated by Whirlpool to service Amana, Admiral, Estate, Inglis, or Roper brands is not available.

9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance

with Whirlpool’s published installation instructions.

10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or

cannot be easily determined.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS

FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and

provinces do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply

to you. This warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to

province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Whirlpool, Amana, Admiral, Estate, Inglis, or Roper dealer to

determine if another warranty applies.

If you think you need repair service, rst see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve

the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Service” section or by

calling the following numbers for assistance: In the U.S.A., call 800-843-0304 for Amana brand products; 800-688-9920 for Admiral

brand products; 800-253-1301 for Estate brand products, or 800-447-6737 for Roper brand products. For assistance In Canada,

call: 800 -807- 6777 for Amana, Admiral, Estate, Inglis, or Roper brand products. 1/12

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your major appliance

to better help you obtain assistance or service if you ever need

it. You will need to know your complete model number and serial

number. You can nd this information on the model and serial

number label located on the product.

Dealer name _____________________________________________

Address __________________________________________________

Phone number ____________________________________________

Model number ____________________________________________

Serial number ____________________________________________

Purchase date ____________________________________________

SÉCURITÉ DE LA SÉCHEUSE

Dans l’État du Massachusetts, les instructions d’installation suivantes sont applicables :

■

Les travaux d’installation et réparation doivent être exécutés par un plombier ou tuyauteur qualifié ou licencié, ou par le

personnel qualifié d’une entreprise licenciée par l’État du Massachusetts.

■

Remplacer par des dispositifs de fermeture acceptables : Les robinets de gaz et robinets à bille installés pour l'utilisation

devraient être indiqués.

■ Si un conduit de raccordement flexible est utilisé, sa longueur ne doit pas dépasser 4 pi (121,9 cm).

– Ne pas entreposer ou utiliser de l’essence ou d’autres vapeurs ou liquidesinflammables

à proximité de cet appareil ou de tout autre appareil électroménager.

– QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :

•

Ne pas tenter d’allumer un appareil.

•

Ne pas toucher à un commutateur électrique; ne pas utiliser le téléphone se trouvant

sur les lieux.

•

Évacuer tous les gens de la pièce, de l’édifice ou du quartier.

•

Appeler immédiatement le fournisseur de gaz d’un téléphone voisin. Suivre ses

instructions.

•

À défaut de joindre votre fournisseur de gaz, appeler les pompiers.

– L’installation et l’entretien doivent être effectués par un installateur qualifié, uneagence

de service ou le fournisseur de gaz.

AVERTISSEMENT :

RISQUE D'INCENDIE OU D'EXPLOSION

Le non-respect des avertissements de sécurité peut causer des dommages à la propriété,

des blessures graves, voire la mort.

IMPORTANT : L'installation du gaz doit se conformer aux codes locaux, ou en l'absence de codes locaux, au code d'installation

du gaz naturel ou du propane, CSA B149.1.

La sécheuse doit être électriquement reliée à la terre conformément aux codes locaux, ou en l'absence de codes locaux, au Code

canadien de l'électricité, partie 1, CSA C22.1.

ACCESSOIRES

Piédestal de 15"

Les piédestaux aux coloris assortis surélèvent

la laveuse et la sécheuse pour les amener à

une hauteur d’utilisation plus confortable. Le

grand tiroir offre une capacité de rangement

pratique.

Ensemble de superposition

Si l’espace disponible est restreint,

l’ensemble de superposition permet

à la sécheuse d’être installée par dessus

la laveuse.

Grille de séchage

La grille de séchage fournit une

surface de séchage stationnaire

pour les articles tels que les

chandails et les chaussures

de tennis. Voir la section

“Caractéristiques supplémentaires”

pour l’information supplémentaire.

Accessoires conçus pour votre appareil :

Personnalisez votre nouvelle laveuse et sécheuse grâce

aux authentiques accessoires Whirlpool suivants. Pour plus

d’informations sur les options et sur les possibilités de

commande, appeler au 1-800-442-9991 ou consulter

www.amana.com/help.

Au Canada, composer le 1-800-807-6777 ou consulter :

www.amana.com/help.

ACCESSOIRES D’INSTALLATION

ET D’ENTRETIEN

PIECES AGRÉÉS PAR LE FABRICANT, ces mots

désignent des pieces de qualité et des accessoires

conçus spécialement pour votre appareil. Une

ingénierie qui a fait ses preuves, pour répondre

a nos normes de qualité les plus strictes.

PIECES AGRÉÉS PAR LE FABRICANT

La page charge ...

Amana NED5800HW Le manuel du propriétaire

Marque: Amana

Modèle: NED5800HW

Catégorie: Sèche-linge

Taper: Le manuel du propriétaire

Ce manuel convient également à

NGD5800HW

Télécharger le PDF

rapport

dans d''autres langues

English: Amana NED5800HW Owner's manual

Amana NED5800HW Le manuel du propriétaire

Ce manuel convient également à

Amana NED5800HW Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents