Winmate R10L OF TR Series Manuel utilisateur

Marque
Winmate
Modèle
R10L OF TR Series
Taper
Manuel utilisateur

Ce manuel convient également à

Please read this instructions before operating the device and retain them for future reference.
Rear Mount Display
8.4”~20.1”
User Manual
Version 1.1
Document Part Number: 91521110101S
2 8.4"~20.1" Rear Mount Display User Manual
Contents
Preface 3
About This User Manual 6
Chapter 1: Introduction 7
1.1 Overview .............................................................................................................. 8
1.2 Product Features .................................................................................................. 8
1.3 Package Contents ................................................................................................ 8
1.4 Product Overview ................................................................................................. 9
1.5 Connectors ......................................................................................................... 10
1.6 OSD Control Panel ............................................................................................. 10
1.6.1 Control Buttons ......................................................................................... 10
1.6.2 LED Indicators .......................................................................................... 11
Chapter 2: Installation 12
2.1 Wiring Requirements .......................................................................................... 13
2.2 Mounting Guide .................................................................................................. 14
2.2.1 VESA Mount ............................................................................................. 14
2.2.2 Rear Mount ............................................................................................... 15
2.3 Cable Mounting Considerations ......................................................................... 16
2.4 Connecting Power .............................................................................................. 16
2.5 Connecting Peripherals ...................................................................................... 17
2.5.1 VGA Connector ........................................................................................ 17
2.5.2 HDMI Connector ....................................................................................... 17
Chapter 3: Operating the Device 18
3.1 Turning on the System ....................................................................................... 19
3.2 OSD Menu Navigation ........................................................................................ 20
3.3 Troubleshooting Guide ....................................................................................... 21
Appendix 22
Appendix A: Frequency Table .................................................................................. 23
3 Preface
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or
by any means, electronic or mechanical, for any purpose, without the prior written permission
of the original manufacturer.
Trademark Acknowledgement
Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer
We reserve the right to make changes, without notice, to any product, including circuits and/or
software described or contained in this manual in order to improve design and/or performance.
We assume no responsibility or liability for the use of the described product(s) conveys no
license or title under any patent, copyright, or masks work rights to these products, and make
no representations or warranties that these products are free from patent, copyright, or mask
work right infringement, unless otherwise specified. Applications that are described in this
manual are for illustration purposes only. We make no representation or guarantee that such
application will be suitable for the specified use without further testing or modification.
Warranty
Our warranty guarantees that each of its products will be free from material and workmanship
defects for a period of one year from the invoice date. If the customer discovers a defect, we
will, at his/her option, repair or replace the defective product at no charge to the customer,
provide it is returned during the warranty period of one year, with transportation charges
prepaid. The returned product must be properly packaged in its original packaging to obtain
warranty service. If the serial number and the product shipping data differ by over 30 days, the
in-warranty service will be made according to the shipping date. In the serial numbers the third
and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g.,
with A for October, B for November and C for December).
For example, the serial number 1W16Axxxxxxxx means October of year 2016.
Customer Service
We provide a service guide for any problem by the following steps: First, visit the website of
our distributor to find the update information about the product. Second, contact with your
distributor, sales representative, or our customer service center for technical support if you
need additional assistance.
You may need the following information ready before you call:
• Product serial number
• Software (OS, version, application software, etc.)
• Description of complete problem
• The exact wording of any error messages
In addition, free technical support is available from our engineers every business day. We are
always ready to give advice on application requirements or specific information on the
installation and operation of any of our products.
4 8.4"~20.1" Rear Mount Display User Manual
Naming Rule
19LXXX-RMXX
Item
Description
R Panel Type
19 Panel Size
LXXX Product Size
RM Mechanical Type (Rear Mount)
XX Panel Model
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful information or
to alert you to the potential for hardware damage or personal injury. These are Notes,
Important, Cautions, and Warnings. The following is an example of each type of advisory.
Note:
A note is used to emphasize helpful information
Important:
An important note indicates information that is important for you to know.
Caution A Caution alert indicates potential damage
to hardware and
explains how to avoid the potential problem.
Attention
Unealerted’ attention indique un dommage possible à
l’équipement et explique comment éviter le problem potentiel.
Warning! An Electrical Shock Warning indicates the potential harm from
electrical hazards and how to avoid the potential problem.
Avertissement!
Un Avertissement de Choc Électriqueindique le potentiel
de chocssur des emplacements électriques et comment éviterces problèmes.
Earth Ground The Protective Conductor Terminal (Earth Ground) symbol
indicates the potential risk of serious electrical shock due to improper
grounding.
Mise à la Terre Le symbole de Miseà Terre indique le risqué potential de
choc électrique grave à la terre incorrecte.
5 Preface
Safety Information
Warning! Always completely disconnect the power cord from your chassis
whenever you work with the hardware. Do not make connections while the
power is on. Sensitive electronic components can be damaged by sudden
power surges. Only
experienced electronics personnel should open the PC
chassis.
Avertissement!
Toujours débrancher le cordon d’alimentation du chassis
lorsque vous travaillez sur celui-
ci. Ne pas brancher de connections lorsque
l’alimentation est présente. Des composantes é
lectroniques sensibles
peuvent être endommagées par des sauts d’alimentation.
Seulement du
personnel expérimenté devrait ouvrir ces chassis.
Caution
Always ground yourself
to remove any static charge before
touching the CPU card. Modern electronic devices are very sensitive to static
electric charges. As a safety precaution, use a grounding wrist strap at all
times. Place all electronic components in a static-dissipative surface or static-
shielded bag when they are not in the chassis.
Attention T
oujours verifier votre mise à la terre afin d’éliminer toute
charge statique avant de toucher la carte CPU. Les équipements
électroniques moderns sont très sensibles aux décharges d’électricité
statique. Toujours utiliser un bracelet de mise à la terre comme précaution.
Placer toutes les composantes électroniques sur une surface conçue pour
dissiper les charge, ou dans un sac anti-
statique lorsqu’elles ne sont pas
dans le chassis.
Safety Precautions
For your safety carefully read all the safety instructions before using the device. Keep this user
manual for future reference.
• Always disconnect this equipment from any AC outlet before cleaning. Do not use liquid
or spray detergents for cleaning. Use a damp cloth.
• For pluggable equipment, the power outlet must be installed near the equipment and
must be easily accessible.
• Keep this equipment away from humidity.
• Put this equipment on a reliable surface during installation. Dropping it or letting it fall
could cause damage.
• The openings on the enclosure are for air convection and to protect the equipment from
overheating.
• Before connecting the equipment to the power outlet make sure the voltage of the power
source is correct.
• Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
• If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient over-voltage.
• Never pour any liquid into an opening. This could cause fire or electrical shock.
• Never open the equipment. For safety reasons, only qualified service personnel should
open the equipment.
• All cautions and warnings on the equipment should be noted.
• Always ground yourself to remove any static charge before touching the board.
6 8.4"~20.1" Rear Mount Display User Manual
About This User Manual
This User Manual provides information about using the Winmate® Rear Mount Display. The
documentation set provides information for specific user needs, and includes:
• Rear Mount Display User Manual – contains detailed description on how to use the
display, its components and features.
Note:
Some pictures in this guide are samples and can differ from actual product.
Document Revision History
Version Date Note
1.0 26-Oct-2017 New document release
1.1 31-Aug-2020
Standard video input change to
1 x VGA (D-sub 15), 1 x HDMI (Type-A)
7 0BChapter 1: Introduction
Chapter 1: Introduction
with
and drawings included in this chapter.
8 8.4"~20.1" Rear Mount Display User Manual
1.1 Overview
Congratulations on purchasing Winmate® Rear Mount Display. Versatile display in an open-
frame housing designed for rear and VESA mounting with integrated bracket design for KIOSK
applications. The design is IP65-sealed from the front side for water and dust protection. It is
designed to meet the demanding performance requirements of today’s business and industrial
applications.
1.2 Product Features
Winmate® Rear Mount Display features:
• 8.4”-20.1” TFT LCD
• Standard 1 x VGA (D-sub 15), 1 x HDMI (Type-A)
• Rear mount
• Suitable for industrial applications
1.3 Package Contents
Carefully remove the box and unpack your display. Please check if all the items listed below
are inside your package. If any of these items are missing or damaged contact us immediately.
Standard factory shipment list:
• Display • User Manual (Hardcopy) • Black screw bolts**
Varies by product Part No. 91521110101S Varies by product
• 110~240V AC Power
Adapter
• Power Cord
• VGA Cable (D-SUB
15pin Male to 15pin
Male)
Varies by product Varies by country Part No. 99441151150P4
•
HDMI Cable (HDMI 19pin
Male to 19pin Male)
•
Remote Control
(Optional)
Part No. 994E0190190P3 Part No. 99B0000000418
*Notice: Screw bolts provided by Winmate only to be used to screw the display onto a console
from the rear side. If you prefer your own bolts, please use M4 and 30mm in length.
9 0BChapter 1: Introduction
1.4 Product Overview
This section describes physical appearance of the Rear Mount Display.
Note:
Notice that standard input terminals include VGA and HDMI. Your device may
be equipped with other input terminals based on your order.
Note:
Notice that input and output connectors vary by product size and specifications.
The picture above shows only a prototype model for information purposes only.
The location of OSD panel may vary by model. Refer to a product datasheet for
more details.
№ Description № Description
①
*RS232 (Remote control)
(Optional)*
④
HDMI
②
*RS232/USB (for Touch) (Optional)*
⑤
DC-in
③
VGA
⑥
OSD Control Panel*
10 8.4"~20.1" Rear Mount Display User Manual
1.5 Connectors
Display input and output connectors are located on the bottom side.
Item Description
Power Jack – Connects computer to source of power.
USB for Touch - Connects USB for touch capabilities.
VGA (RGB) –Transmits video from a PC to a monitor.
Example: A notebook PC to a monitor.
HDMI –Transmits and protects copyrighted digital video and audio.
Example: An HD tuner to an HD ready TV.
1.6 OSD Control Panel
1.6.1 Control Buttons
OSD control panel varies by product specifications. Refer to a product datasheet to check the
OSD control panel type of a particular model.
Type A
Icon Function
Decrease the value / Select up
Increase the value / Select down
Power switch
Select left
Select right / Call main OSD menu
11 0BChapter 1: Introduction
Type B
Icon Function
Decrease the value / Select up
Increase the value / Select down
Power switch
Exit / Auto adjustment
Enter / Call main OSD menu
1.6.2 LED Indicators
LED indicators are located on the OSD control panel the rear side of the display.
Icon
Description
Function
Power Lights up in "Green" when the monitor turn on
Stand by
Lights up in "Orange" when the device cannot detect any
input source
12 8.4"~20.1" Rear Mount Display User Manual
Chapter 2: Installation
to cautions and warning to avoid any damages
13 1BChapter 2: Installation
2.1 Wiring Requirements
The following common safety precautions should be observed before installing any electronic
device:
• Strive to use separate, non-intersecting paths to route power and networking wires. If
power wiring and device wiring paths must cross make sure the wires are perpendicular
at the intersection point.
• Keep the wires separated according to interface. The rule of thumb is that wiring that
shares similar electrical characteristics may be bundled together.
• Do not bundle input wiring with output wiring. Keep them separate.
• When necessary, it is strongly advised that you label wiring to all devices in the system.
Caution/ Attention
• Do not run signal or communication wiring and power wiring in the same conduit. To
avoid interference, wires with different signal characteristics (i.e., different interfaces)
should be routed separately.
• Be sure to disconnect the power cord before installing and/or wiring your device.
• Verify the maximum possible current for each wire gauge, especially for the power cords.
Observe all electrical codes dictating the maximum current allowable for each wire
gauge.
• If the current goes above the maximum ratings, the wiring could overheat, causing
serious damage to your equipment.
Be careful when handling the unit. When the unit is plugged in, the internal components
generate a lot of heat which may leave the outer casing too hot to touch.
14 8.4"~20.1" Rear Mount Display User Manual
2.2 Mounting Guide
The Rear Mount Display can be applied for several different installation methods, including
VESA mount. Refer to sub-sections below for more details.
Caution
Follow mounting instructions and use recommended mounting
hardware to avoid the risk of injury.
Attention Suivez les instructions de montage et d'utilisation recommandé
le matériel de montage pour éviter le risque de blessure.
2.2.1 VESA Mount
Rear Mount Display comes with VESA Mount holes for mounting. Winmate provides VESA by
request.
Installation Instruction:
1. Screw VESA bracket to the fixture (ex. swing arm) with four VESA screws.
2. Place the device on VESA bracket.
Notice that VESA stand and mounting kit are not provided by Winmate.
15 1BChapter 2: Installation
2.2.2 Rear Mount
The Rear Mount Display comes with the bracket that enables you to install the unit onto a wall
(where space has been cut out to accommodate the rest of the hardware).
Installation Instruction
1. Make a cutout on the fixture (ex. wall) according to the cutout dimension of the display.
Note: All installation processes will be done from the rear side of the fixture.
2. Based on the drawing mark screw holes on a rear side of the fixture. Place the display
on the fixture from the front side. The sides of the bezel should be visible from outside.
3. Use electric screwdriver to fasten M4 screws from the rear side of the front bezel.
4. You complete the installation. Please connect all the peripherals if needed.
❶
❷
❸
❹
16 8.4"~20.1" Rear Mount Display User Manual
2.3 Cable Mounting Considerations
For a nice look and safe installation, make sure cables are neatly hidden behind the device.
Caution
Observe all local installation requirements for connection cable type
and protection level.
Attention
Suivre tous les règlements locaux d’installations, de câblage et
niveaux de protection.
Caution
Turn off the device and disconnect other peripherals before installation.
Attention
Éteindre l’appareil et débrancher tous les périphériques avant
l’installation.
2.4 Connecting Power
This section provides information on how to use connectors on the Rear Mount Display. Be
cautious while working with these modules. Please carefully read the content of this chapter in
order to avoid any damages.
Installation instruction:
1. Connect the AC cord to the AC IN terminal on the AC adaptor.
2. Connect the DC OUT terminal of the AC adaptor to the DC IN terminal on the monitor.
3. Align the notch on the cord connector with the guiding groove and plug it in.
4. Connect the AC cord plug to the power outlet.
17 1BChapter 2: Installation
2.5 Connecting Peripherals
The panel control port is designed for monitors that work with a variety of compatible video
sources. Due to the possible deviations between these signal sources, you may have to make
adjustments to the monitor settings from the OSD menu when switching between these
sources.
Note:
Notice that standard input terminals include VGA and HDMI. Your
device may be equipped with other input terminals based on your order.
2.5.1 VGA Connector
Rear Mount Display uses standard 15pin D-sub connector. Plug 15-pin VGA signal cable to
the VGA connector in the rear of motherboard, and plug the other end to the monitor. Secure
cable connectors with hexagonal copper pillars M3x4mm.
Pin assignment and signal names for VGA connector
2.5.2 HDMI Connector
Plug HDMI signal cable to the HDMI connector on the rear side of PC system, and plug the
other end to the monitor.
Pin assignment and signal names for HDMI connector
Pin №
Signal Name
Pin №
Signal Name
1
RED
2
GREEN
3
BLUE
4
NC
5
GND
6
AGND
7
AGND
8
AGND
9
VGA_5V
10
GND
11
NC
12
DDCSDA
13
H Sync
14
V Sync
15
DDCSCL
Pin №
Signal Name
Pin №
Signal Name
1
HDMI_RX2+
2
GND
3
HDMI_RX2-
4
HDMI_RX1+
5
GND
6
HDMI_RX1-
7
HDMI_RX0+
8
GND
9
HDMI_RX0-
10
HDMI_RXC+
11
GND
12
HDMI_RXC-
13
HDMI_CON_CEC
14
NC
15
HDMI_CON_SCL
16
HDMI_CON_SDA
17
GND
18
+5V_HDMI
19
HDMI_CON_HP
18 8.4"~20.1" Rear Mount Display User Manual
Chapter 3: Operating the Device
display.
19 2BChapter 3: Operating the Device
3.1 Turning on the System
To turn on the system:
1. Connect the power adapter cable to the DC IN of the display.
2. Connect the power cord to the power adapter.
3. Connect the power cord to a power outlet.
4. Press the power button located on the OSD control panel on the rear to turn on the
system.
20 8.4"~20.1" Rear Mount Display User Manual
3.2 OSD Menu Navigation
OSD Icon Sub-menu Settings Note
BRICONTRAST
BRIGHTNESS slider bar Default 50
Use to adjust the screen’s brightness. Range 0 to 100
CONTRAST slider bar Default 50
Use to adjust the screen’s contrast. Range 0 to 100
POSITION
H POSITION
slider bar
Default 50
Use to adjust the image to the left or right on the screen.
Range 0 to 100
V POSITION
slider bar
Default 50
Use to adjust the image up or down on the screen. Range 0 to 100
IMAGE
AUTO
Select and execute
Use to choose the best settings for the current input signal
CLOCK
slider bar
Default 50
Use to adjust the value of horizontal image. Range 0 to 100
PAHSE
slider bar
Default 50
Use to adjust the phase control (Phase adjustment may be required to
optimize the display quality)
WHITE BALANCE
Select and execute
Use to set RGB signal voltage level
COLOR
USER
R.G.B slider bar
Choose RED/GREEN/BLUE to set value of color temperature brightness to
suit your own preference
9300K
Select and execute
Use to set value of monitor for the CIE coordinate 9300 color temperature
6500K
Select and execute
Use to set value of monitor for the CIE coordinate 6500 color temperature
ADC RIGHTNESS
slider bar
Default 50
Set value of monitor for ADC Brightness. Range 0 to 100
GAMMA
GAMMA 0 Select and execute
Default
GAMMA0
Choose the parameter of GAMMA 0 as default setting.
GAMMA 1
Select and execute
Choose the parameter of GAMMA 1 as default setting.
GAMMA 2
Select and execute
Choose the parameter of GAMMA 2 as default setting.
OP
OPTION
VR Brightness
ON/OFF
Default OFF
Choose the brightness control mode by VR control
Volume
slider bar
Default 10
Use to set value of Volume
Speaker
ON/OFF
Default OFF
Use to set value of Volume Speaker
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24

Winmate R10L OF TR Series Manuel utilisateur

Marque
Winmate
Modèle
R10L OF TR Series
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes