Aiwa XH-A1000 Operating Instructions Manual

E (Español)

COMPACT DISC STEREO SYSTEM

SISTEMA ESTEREO CON REPRODUCTOR DE DISCOS COMPACTOS

CHAINE STEREO AVEC LECTEUR DE DISQUES COMPACTS

U

En (English)

8A-MTM-903-11

000223BKY-Y-M

F (Français)

OPERATING INSTRUCTIONS

MANUAL DE INSTRUCCIONES

MODE D’EMPLOI

XH-A1000

For assistance and information

call toll free 1-800-BUY-AIWA

(United States and Puerto Rico)

CORRECTION

Please read the incorrect description in the

Operating Instructions as follows.

Page 21

AI EDIT RECORDING

WRONG

6

Press q REC/REC MUTE to start

recording.

RIGHT

6

Press qREC/REC MUTE and then press

c /d within 2 seconds to start

recording.

Page 22

PROGRAMMED EDIT

RECORDING

WRONG

8

Press q REC/REC MUTE to start

recording.

RIGHT

8

Press qREC/REC MUTE and then press

c /d within 2 seconds to start

recording.

XH-A1000

CORRECTION

Prière d’apporter les corrections suivantes au

mode d’emploi.

Page 21

ENREGISTREMENT PAR

MONTAGE INTELLIGENT

MAUVAIS

6

Appuyez sur qREC/REC MUTE pour

lancer l’enregistrement.

BON

6

Appuyez sur qREC/REC MUTE puis

appuyer sur c/d dans les 2 secondes

qui suivent pour lancer l’enregistrement.

Page 22

ENREGISTREMENT PAR

MONTAGE PROGRAMME

MAUVAIS

8

Appuyez sur qREC/REC MUTE pour

lancer l’enregistrement.

BON

8

Appuyez sur qREC/REC MUTE puis

appuyer sur c/d dans les 2 secondes

qui suivent pour lancer l’enregistrement.

8A-MTM-919-01

0001A-Y

Printed in Japan

CORRECCION

Interprete, porfavor, las descripciones

incorrectas del manual de la forma sigulente.

Página 21

GRABACIÓN DE EDICIÓN AI

ERRONEO

6

Presione qREC/REC MUTE para iniciar

la grabación.

ORRECTO

6

Presione q REC/REC MUTE y luego

pulse c /d antes de que pasen 2

segundos para iniciar la grabación.

Página 22

GRABACIÓN DE EDICIÓN

PROGRAMADA

ERRONEO

8

Presione qREC/REC MUTE para iniciar

la grabación.

ORRECTO

8

Presione q REC/REC MUTE y luego

pulse c /d antes de que pasen 2

segundos para iniciar la grabación.

2

ENGLISH

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

Owner’s record

For your convenience, record the model number and serial

number (you will find them on the rear of your unit) in the space

provided below. Please refer to them when you contact your Aiwa

dealer in case of difficulty.

Model No. Serial No. (Lot No.)

CX-A1000

SX-WA1000

SX-C1800

SX-R1800

3 Mounting surface — Place the unit on a flat, even surface.

4 Ventilation — The unit should be situated with adequate

space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and the top of the

unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that

may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack

where ventilation may be impeded.

5 Objects and liquid entry — Take care that objects or liquid

do not get inside the unit through the ventilation openings.

6 Carts and stands — When placed or

mounted on a stand or cart, the unit should

be moved with care.

Quick stops, excessive force, and uneven

surfaces may cause the unit or cart to overturn

or fall.

7 Condensation — Moisture may form on the CD pickup lens

when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function

normally. Should this occur, leave the unit for a few hours,

then try to operate again.

8 Wall or ceiling mounting — The unit should not be mounted

on a wall or ceiling, unless specified in the Operating

Instructions.

Electric Power

1 Power sources — Connect this unit only to power sources

specified in the Operating Instructions, and as marked on the

unit.

2 Polarization — As a safety feature, some units are equipped

with polarized AC power plugs which can only be inserted

one way into a power outlet. If it is difficult or impossible to

insert the AC power plug into an outlet, turn the plug over and

try again. If it is not still inserted easily into the outlet, please

call a qualified service technician to service or replace the

outlet. To avoid defeating the safety feature of the polarized

plug, do not force it into a power outlet.

3 AC power cord

- When disconnecting the AC power cord, pull it out by the

AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this

could result in fire or shock.

- Power cords should be firmly secured to avoid being severely

bent, pinched, or walked upon. Pay particular attention to

the cord from the unit to the power socket.

- Avoid overloading AC outlets and extension cords beyond

their capacity, as this could result in fire or shock.

4 Extension cord — To help prevent electric shock, do not use

a polarized AC power plug with an extension cord, receptacle,

or other outlet unless the polarized plug can be completely

inserted to prevent exposure of the blades of the plug.

5 When not in use — Unplug the AC power cord from the power

outlet if the unit will not be used for several months or more.

When the cord is plugged in, a small amount of current

continues to flow to the unit, even when the power is turned

off.

“CAUTION:TO REDUCE THE RISK OF

ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.”

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

PRECAUTIONS

Read the Operating Instructions carefully and completely before

operating the unit. Be sure to keep the Operating Instructions

for future reference. All warnings and cautions in the Operating

Instructions and on the unit should be strictly followed, as well

as the safety suggestions below.

Installation

1 Water and moisture — Do not use this unit near water, such

as near a bathtub, washbowl, swimming pool, or the like.

2 Heat — Do not use this unit near sources of heat, including

heating vents, stoves, or other appliances that generate heat.

It also should not be placed in temperatures less than 5°C

(41°F) or greater than 35°C (95°F).

ENGLISH

3

En

SOUND

TABLE OF CONTENTS

PREPARATIONS

CHECK YOUR SYSTEM AND ACCESSORIES .................4

BASIC CONNECTIONS ......................................................4

CONNECTING OTHER EQUIPMENTS ..............................6

CONNECTING A DVD PLAYER .........................................8

REMOTE CONTROL ...........................................................9

BEFORE OPERATION........................................................9

SOUND

AUDIO ADJUSTMENTS .................................................. 11

GRAPHIC EQUALIZER.................................................... 12

DSP SURROUND............................................................. 13

RADIO RECEPTION

MANUAL TUNING ............................................................ 14

PRESETTING STATIONS ................................................ 15

TAPE PLAYBACK

BASIC OPERATIONS ...................................................... 16

CD PLAYING

BASIC OPERATIONS ...................................................... 17

PROGRAMMED PLAY ..................................................... 19

RECORDING

BASIC RECORDING........................................................ 20

AI EDIT RECORDING ...................................................... 21

PROGRAMMED EDIT RECORDING............................... 22

DOLBY SURROUND

ADJUSTING SPEAKER LEVEL...................................... 23

PLAY WITH DOLBY PRO LOGIC.................................... 24

LISTENING TO DOLBY DIGITAL SURROUND SOUND ...... 25

KARAOKE

MICROPHONE MIXING ................................................... 26

CD KARAOKE PROGRAM.............................................. 28

CLOCK AND TIMER

SETTING THE CLOCK..................................................... 29

SETTING THE SLEEP TIMER ......................................... 29

SETTING THE TIMER ...................................................... 30

GENERAL

CARE AND MAINTENANCE ........................................... 31

SPECIFICATIONS ............................................................ 32

TROUBLESHOOTING GUIDE ......................................... 33

PARTS INDEX ...................................................

Back cover

Outdoor Antenna

1 Power lines — When connecting an outdoor antenna, make

sure it is located away from power lines.

2 Outdoor antenna grounding — Be sure the antenna system

is properly grounded to provide protection against unexpected

voltage surges or static electricity build-up. Article 810 of the

National Electrical Code, ANSI/NFPA 70, provides information

on proper grounding of the mast, supporting structure, and

the lead-in wire to the antenna discharge unit, as well as the

size of the grounding unit, connection to grounding terminals,

and requirements for grounding terminals themselves.

ANTENNA LEAD IN WIRE

ANTENNA DISCHARGE

UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250 PART H)

NEC-NATIONAL ELECTRICAL CODE

ELECTRIC

SERVICE

EQUIPMENT

GROUND CLAMP

Antenna Grounding According to the National Electrical Code

Maintenance

Clean the unit only as recommended in the Operating

Instructions.

Damage Requiring Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have got inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF.

4

ENGLISH

PREPARATIONS

CHECK YOUR SYSTEM AND

ACCESSORIES

CX-A1000 Compact disc stereo cassette receiver

SX-WA1000 Front speakers

SX-C1800 Center speaker

SX-R1800 Surround speakers

Remote control AM antenna FM antenna

Operating Instructions, etc.

BASIC CONNECTIONS

The DOLBY PRO LOGIC system which is the biggest feature of

this stereo system provides you with multichannel sound in your

home. Enjoy the enriched home theater system by connecting

the TV set or video equipments with this unit.

Complete setting and connection of the main unit, supplied

speakers, your TV and video equipments according to the

following procedure.

Before connecting the AC cord

The rated voltage of your unit shown on the rear panel is 120 V

AC. Check that the rated voltage matches your local voltage.

IMPORTANT

Connect the speakers, antennas, and all optional equipment first.

Then connect the AC cord.

There are no difference between the front speakers as well as

the surround speakers. Both speakers of its kind can be

connected as L (left) or R (right).

1

Connect the right speaker to the main unit.

1 Connect the speaker cord with the white stripe to the

SPEAKERS LOW FREQ R 0 terminal and the black cord

to the 9 terminal.

Wind the tip of the cord around the terminal. Then tighten

the terminal. Check that the cord is connected securely.

SPEAKER

IM

P : 6

Ω

XH-A1000

ENGLISH

5

En

SOUND

PREPARATIONS

S

P

E

A

K

E

R

S

HIGH FREQ

S

P

E

A

K

E

R

S

HIGH FREQ

To position the antennas

FM antenna:

Extend the antenna horizontally in a T-shape and fix its ends to

a wall.

AM antenna:

Position and rotate this antenna to find the best reception.

To stand the AM antenna on a surface

Fix the claw to the slot.

FM antenna

AM antenna

2 Connect the blue colored speaker cord to SPEAKERS

HIGH FREQ R jack.

2

Connect the left speaker to the main unit.

Connect the blue colored speaker cord to SPEAKERS HIGH

FREQ L terminal, and another speaker cord to the

SPEAKERS LOW FREQ L terminals in the same manner as

step 1.

3

Connect the surround speakers to the main unit.

Connect the right surround speaker cord to SURROUND

SPEAKERS R terminal, and the left to SURROUND

SPEAKERS L terminal.

4

Connect the center speaker.

Connect the center speaker cord to CENTER SPEAKER

terminal.

5

Connect the supplied antennas.

Connect the FM antenna to FM 75 Ω terminals and the AM

antenna to AM LOOP terminals.

6

Connect other equipments.

Some audio and video equipments (LD player, MD player,

DVD player, TV, etc.) can be connected to this unit.

See page 6 for details.

7

Connect the AC cord to an AC outlet.

The DEMO (Demonstration) will begin when the AC cord is

plugged into an AC outlet for the first time after purchase. To

deactivate the DEMO, set the clock.

POSITIONING THE SPEAKERS

To achieve the optimum effects obtainable with the DOLBY PRO

LOGIC system, it is important to position the speakers properly.

Refer to the following illustration to find out the best location in

your room.

1 Front speakers

2 Center speaker

Position in the center of the two front speakers. In addition,

position on or below the TV set, if connecting a TV set to the

unit.

3 Surround speakers

Place the surround speakers directly to the side of or slightly

behind the listening area. Align them horizontally, about 1

meter above ear height.

NOTE

• No sound is heard from the center and surround speakers when

the DOLBY PRO LOGIC, the DSP SURROUND system and

the 5.1CH (page 25) are set to off.

• The sound is heard from the center speaker when the DOLBY

PRO LOGIC or the 5.1CH (page 25) is set to on.

12 1

3

6

ENGLISH

NOTE

• Be sure to connect the speaker

cords correctly. Contact of bare

conductor with other jacks or

other conductors may cause short

circuits in SPEAKERS terminals

or malfunctions.

• Do not leave objects generating magnetism, such as credit

cards, near the speakers, as the objects may be damaged.

• Do not bring the FM antenna near metal objects or curtain rails.

• Do not bring the AM antenna near other optional equipment,

the stereo system itself, the AC cord or speaker cords, since

noise will be picked up.

• Do not unwind the AM antenna wire.

S

P

E

A

K

E

R

I

M

P

:

6

Ω

CONNECTING AN OUTDOOR ANTENNA

For better FM reception, use of an outdoor antenna is

recommended.

Connect the outdoor antenna to FM 75 Ω terminals.

VIDEO2/LD/TV jacks

A video equipment, an LD player or a cable TV, etc. can be

connected to these jacks.

• Use the audio cable and video cable commercially available.

• To input signals from the connected equipment to this unit,

connect the cables to VIDEO2/LD/TV IN jacks.

To output signals from this unit to the connected equipment,

connect the cables to VIDEO2/LD/TV OUT jacks.

• Connect L (left) output of the connected equipment and AUDIO

L of this unit, R (right) output and AUDIO R by the audio cable.

VIDEO3 jacks

A video equipment, a camcorder or a TV game, etc. can be

connected to these jacks. Turn VOLUME to "0" before connecting

equipment to VIDEO 3 jacks.

• Use the audio cable and video cable commercially available.

• Connect L (left) output of the connected equipment and AUDIO IN

L of this unit, R (right) output and AUDIO IN R by the audio cable

.

• Connect Video output of the connected equipment and VIDEO

IN of this unit by the video cable.

REC OUT/AUDIO MONITOR jacks

A recording equipment such as an MD recorder, a CD-R/RW recorder

or a cassette deck, or the TV set etc. can be connected to these jacks.

The sounds from the equipment connected to VIDEO1/DVD/MD

or VIDEO2/LD/TV can be recorded or monitored as well.

• Use the audio cable commercially available.

• Connect L (left) output of the connected equipment and AUDIO

L of this unit, R (right) output and AUDIO R by the audio cable.

MONITOR/VIDEO OUT jacks

The TV set, etc. can be connected to these jacks.

The videos from the equipment connected to VIDEO1/DVD/MD

or VIDEO2/LD/TV can be monitored.

• Use the video cable commercially available.

CD DIGITAL OUT (OPTICAL) jack

A digital equipment such as an MD recorder, a DAT deck, a digital

cassette deck or a digital amplifier, etc. can be connected to this

jack. The digital signals from the CD player of this unit are output

to the connected equipment.

• Use the optical cable commercially available.

• Before connecting an optical cable remove the dust cap a

from CD DIGITAL OUT (OPTICAL) jack.

• When CD DIGITAL OUT (OPTICAL) jack is not used, attach

the dust cup a.

PHONO IN jacks

A turntable can be connected to these jacks. Use an Aiwa

turntable equipped with a built-in equalizer amplifier.

AUX IN jacks

A playback equipment such as the TV set or an MD player, etc.

can be connected to these jacks.

• Use the audio cable and video cable commercially available.

• Connect L (left) output of the connected equipment and AUDIO

L of this unit, R (right) output and AUDIO R by the audio cable.

NOTE

The signals input through VIDEO 1 IN jack are output from VIDEO

2 OUT or MONITOR OUT. The signals input through VIDEO 2 IN

jack are output from VIDEO 1 OUT or MONITOR OUT.

To mount the surround speakers on a wall

Use wall mounting screws (not supplied).

Select a spot that will hold the weight of the speakers and

carefully mount the surround speakers so that they are firmly

secured.

Aiwa disclaims any

responsibility for injury to

persons or other accidents

caused by not fitting the

surround speakers properly

or if the place of the

installation is not suitable.

CONNECTING OTHER

EQUIPMENTS

A video equipment, the TV set, an LD player, a DVD player or an

MD player, etc. can be connected to this unit.

VIDEO1/DVD/MD jacks

A video equipment, a DVD player, or an MD player, etc. can be

connected to these jacks.

• Use the audio cable and video cable commercially available.

• To input signals from the connected equipment to this unit,

connect the cables to VIDEO1/DVD/MD IN jacks.

To output signals from this unit to the connected equipment,

connect the cables to VIDEO1/DVD/MD OUT jacks.

• Connect L (left) output of the connected equipment and AUDIO

L of this unit, R (right) output and AUDIO R by the audio cable.

ENGLISH

7

En

SOUND

REC OUT/

AUDIO

MONITOR

MONITOR/

VIDEO OUT

VIDEO2/LD/TV

VIDEO1/DVD/MD

VIDEO2/LD/TV

VIDEO1/DVD

CD DIGITAL OUT

(OPTICAL)

PHONO IN

AUX IN

o

Connection example

CX-A1000 (front)

CX-A1000 (rear)

Video deck, LD player,

Cable TV, etc.

DVD deck, Video deck, MD

player, etc.

Turntable

CD-ROM driver,

MD recorder, etc.

to Audio out jacks

and Video out jack

to Audio out

jacks and

Video out jack

to Audio in jacks

to Audio in jacks and

Video in jack

to Audio out jacks and

Video out jack

to Audio in jacks and

Video in jack

TV

to Video in jack

to Audio out jacks

to Digital in jack

Camcorder

PREPARATIONS

8

ENGLISH

SELECTING EXTERNAL AUDIO/VIDEO

SOURCES

To play equipment connected to the unit, proceed as follows.

1

Press VIDEO1/2/3 or AUX/PHONO/5.1CH

repeatedly to select a desired source.

The source names are displayed cyclically as below.

When VIDEO1/2/3 is pressed

When AUX/PHONO/5.1CH is pressed

Select one of the sources depending on the equipment

connected to the input terminals on the unit.

∗

While the headphones are plugged in, 5.1chIN is not displayed.

2

Play the connected equipment.

To monitor a video source

The selected video source is indicated on the display and the

video signal through MONITOR/VIDEO OUT jack is output on

the TV.

To adjust the sound level of equipments connected to

the input jacks (except a equipment connected to PHONO

jacks)

When the sound level of the external source is much higher or

much lower than that of other function sources, adjust it as follows.

1 Press VIDEO1/2/3 or AUX/PHONO/5.1CH repeatedly so that

the name of the jacks connected with the concerned

equipment is displayed.

Example: To adjust the sound level of equipment connectedto

VIDEO 1, press VIDEO1/2/3 repeatedly to display VIDEO1.

2 Play the equipment.

3 Press f or g until the sound level becomes the same

as that of other function sources.

NOTE

• During recording, the sound level can not be adjusted.

• The sound level of the connected turntable cannot be adjusted.

CONNECTING A DVD PLAYER

5.1CH INPUT jacks of this unit support the DOLBY DIGITAL

SURROUND system (see page 25).

Connect a DVD player with 5.1ch output jacks to this unit using

cables with RCA phono plugs as follows:

This unit’s jack DVD player’s jack

5.1CH INPUT FRONT (L, R) 5.1CH OUTPUT FRONT (L, R), etc.

5.1CH INPUT SURROUND (L, R) 5.1CH OUTPUT SURROUND (L, R), etc.

5.1CH INPUT CENTER 5.1CH OUTPUT CENTER, etc.

5.1CH INPUT SUB WOOFER 5.1CH OUTPUT SUB WOOFER, etc.

VIDEO/AUX IN (L, R) LINE OUT (L, R), etc.

(See NOTE .)

NOTE

• If the DVD player is not connected to AUX IN jacks:

- the spectrum analyzer does not show the sound level of the

DVD player.

- the sound from the connected DVD player cannot be recorded.

To remove these limitations, connect LINE OUT jacks of the

DVD player to AUX IN jacks of this unit besides connecting to

5.1CH INPUT jacks.

The signals through AUX IN jacks enable the spectrum analyzer

to work and the recording to be done.

Refer also to the operating instructions of the DVD player.

• The DOLBY DIGITAL SURROUND sound cannot be recorded

in any way.

NOTE

VIDEO 1/2/3

AUX/PHONO/5.1CH

f,g

VIDEO1 VIDEO2 VIDEO3

AUX 5.1chIN

∗

PHONO

ENGLISH

9

En

SOUND

REMOTE CONTROL

Inserting batteries

Detach the battery cover on the rear of the remote control and

insert two R6 (size AA) batteries.

When to replace the batteries

The maximum operational distance between the remote control

and the sensor on the main unit should be approximately 5 meters

(16 feet). When this distance decreases, replace the batteries

with new ones.

Using the remote control

The instructions in this manual refer mainly to the buttons on the

main unit. Buttons on the remote control with the same names

as those on the main unit can be used as well.

c/d PRESET on the remote control

The function is the same as that of d on the main unit.

NOTE

• If the remote control is not going to be used for an extended

period of time, remove the batteries to prevent possible

electrolyte leakage.

• The remote control may not operate correctly when:

- The line of sight between the remote control and the remote

sensor inside the display window is exposed to intense light,

such as direct sunlight

- Other remote controls are used nearby (those of a television,

etc.)

BEFORE OPERATION

To turn the power on

Press one of the function buttons (TAPE, TUNER/BAND, VIDEO1/

2/3, AUX/PHONO/5.1CH or CD).

Playback of the inserted disc or tape begins, or the previously

tuned station is received (Direct Play Function).

POWER is also available.

To turn the power off

Press POWER.

Illumination guide

Whenever POWER or one of the function buttons is pressed,

the buttons for the selected operation light up or flash.

Example:

When CLOCK is pressed, f and g light as a

guide to setting the current time.

Demo mode

When the AC cord is plugged into an AC outlet for the first time

after purchase, the Demo mode will begin in the display window.

When the power is turned on, the Demo mode will end. When

the power is turned off, the Demo mode will begin again.

Until the clock is set, the Demo mode will begin whenever the

power is turned off.

When the clock is set, the Demo mode will not begin even if the

power is turned off. (See “SETTING THE CLOCK” on page 29

to set the clock.)

To activate the Demo mode

Press DEMO while the power is turned on or off. The Demo mode

will begin in the display window.

When one of the button is pressed or the control is turned, the

Demo mode will end.

SETTING DISPLAY MODE

By pressing FL DISPLAY as following, the illumination color,

brightness level of the display and the spectrum analyzer display

can be changed.

To change the illumination color

The lighting color around the function buttons and above the CD

compartment can be changed.

1 Press FL DISPLAY

once so that the current mode is displayed.

2 Within 4 seconds, turn MULTI JOG to select the illumination

color. The modes are displayed cyclically as below.

The color will be automatically set after 4 seconds.

FL DISPLAY

Function

buttons

POWER

BLUE UMBER PURPLE

PREPARATIONS

10

ENGLISH

SETTING POWER ECONOMIZING MODE

Setting this unit to power economizing mode reduces power

consumption as follows.

ECO ON

• When the power is turned off, all the display lights turn off, and

only the indicator on POWER lights; however, when the clock

is not set, the window turns to the demo display.

• When the power turns on due to timer recording (page 30), the

display brightness level is set to “DIMMER 3”, all button lamps

are off, and the volume is set to the minimum level (0).

• The display brightens only when operating the unit. When the

unit has not been used for 10 seconds, the brightness level

switches to the dimmer mode previously selected.

(If the display brightness level is set to “DIM-OFF”, the

brightness does not change. When the level is “DIMMER 3”,

the button lamps are also turned off.)

ECO AUTO

• In addition to the conditions of ECO ON, if CD or tape does not

play for 10 minutes or if there is no audio input from any

connected external equipment for 10 minutes when VIDEO1,

2, 3, AUX or PHONO is selected as the source, the power shuts

off. Exceptionally, the power does not shut off when the 5.1CH

is selected.

ECO OFF

The economizing mode does not work.

To change the brightness level of the display

1 Press FL DISPLAY twice so that the current mode is

displayed.

2 Within 4 seconds, turn MULTI JOG to select the dimmer mode.

The modes are displayed cyclically as below.

The mode will be automatically set after 4 seconds. 3.

DIM-OFF: The normal display.

DIMMER 1: The illumination of the display is dimmer than

usual.

DIMMER 2: The illumination of the display is dimmer than

DIMMER 1.

DIMMER 3: The illumination of the display is dimmer than

DIMMER 2. The spectrum analyzer and the

button lamps light off.

To change the spectrum analyzer display

1 Press FL DISPLAY three times so that the current mode is

displayed.

2 Within 4 seconds, turn MULTI JOG to select the spectrum

analyzer display. The modes are displayed cyclically as below.

The mode will be automatically set after 4 seconds.

MULTI JOG

ECO

CLOCK

ENTER

NORMAL REVERSE PEAK

1

Press ECO.

The current power-economizing mode status (ECO OFF/ECO

ON/ECO AUTO) will be displayed.

2

Turn MULTI JOG within 4 seconds to change the

power-economizing mode.

3

Within 4 seconds, press ENTER to set the

selected power-economizing mode.

Standby power consumption

If the power-economizing mode is OFF: 55 W

If the power-economizing mode is ON or AUTO: 1.9 W

NOTE

To view the clock when all the display lights turn off, press CLOCK

so that the time is displayed for 4 seconds.

4-CHANNEL MULTI-AMPLIFIER SYSTEM

To provide reinforcement for the ultra-low frequencies, in addition

to the Left/Right 2-channel amplifier used to reproduce mud-to-

high-range frequencies, this system incorporates a second L/R

2-channel amplifier just for reproduction of ultra-low frequencies

–making it, in effect, a 4-amplifier system. By utilizing discrete

amplifiers for mid to-high-frequencies and low frequencies, high-

quality sonic reproduction that is virtually free from distortion

can be realized.

This Multi Amplifier System, which utilizes independent circuitry

for the different frequency ranges, enables superb sonic

reproduction free from distortion.

BUILT-IN SUBWOOFER SYSTEM

The built-in subwoofer system has a separate subwoofer cavity

area that is part of the loudspeaker cabinet structure, which acts

as a sonic filter to cut distortion components. (In the Multi

Amplifier System, the ultra-low frequency signals transmitted from

their own independent amplifier are reproduced in this area.)

This separate construction gives a clear, rich definition to bass

reproduction and it can realize clear, well-defined mid-to-high

frequency signals.

And AIWA's built-in subwoofer system incorporates a subwoofer

capable of powerful, satisfying bass performance with true stereo

separation.

ENGLISH

11

En

SOUND

AUDIO ADJUSTMENTS

VOLUME CONTROL

Turn VOLUME on the main unit, or press VOL N

or M on the remote control.

The volume level is displayed as a number from 0 to MAX (50).

The volume level is automatically set to 20 when the power is

turned off with the volume level set to 21 or more.

To change the left/right balance

Press MANUAL SELECT on the remote control. L/R is displayed

for 2 seconds. Press

ff

f or

gg

g on the remote control within

these 2 seconds.

• The DOLBY PRO LOGIC (page 24) and the DOLBY DIGITAL

SURROUND (page 25) front speakers level is also changed.

SOUND

Using the headphones

Connect headphones to PHONES jack with a stereo standard

plug (ø6.3 mm,

1

/4 inch).

No sound is output from the speakers while the headphones are

plugged in.

• When the headphones are plugged in, the DSP SURROUND

system (page 13), the DOLBY PRO LOGIC (page 24) and the

5.1CH (page 25) do not function.

BBE SYSTEM

The BBE system enhances the clarity of high-frequency sound.

It also enriches the Karaoke function to make your voice sound

clear and pleasant.

Press BBE.

Each time it is pressed, the level changes. Select one of the

three levels or the off position to suit your preference.

NOTE

When playing back a tape recorded with BBE, it is recommended

that BBE be set to off to avoid distorted high frequency sound.

SUPER T-BASS SYSTEM

The T-BASS system enhances the realism of low-frequency

sound.

Press T-BASS.

Each time it is pressed, the level changes. Select one of the

three levels or the off position to suit your preference.

NOTE

Low-frequency sound may be distorted when the T-BASS system

is used for a disc or tape in which low-frequency sound is already

emphasized. In this case, cancel the T-BASS system.

PREPARATIONS

SOUND

PHONES

BBE

T-BASS

VOL /

f,

g

MANUAL

SELECT

VOLUME

12

ENGLISH

GRAPHIC EQUALIZER

SELECTING THE PROGRAMMED

EQUALIZATION CURVE

This unit provides the following 5 different equalization curves.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

LATIN: Accented higher frequencies for latin-type music

CLASSIC: Enriched sound with heavy bass and fine treble

JAZZ: Accented lower frequencies for jazz-type music.

1

Press GEQ.

The current mode is displayed.

2 Within 4 seconds, turn MULTI JOG or press f

or g to select a desired mode. The modes are

displayed cyclically as below.

The mode will be automatically set after 4 seconds.

To cancel the selected mode

Press GEQ twice so that “GEQ OFF” is displayed.

To select with the remote control

Press GEQ repeatedly until the desired program mode is

displayed. Each mode and “GEQ OFF (cancel)” appear cyclically.

SETTING A NEW EQUALIZATION CURVE

MANUALLY

The equalization curve can be customized to suit your preference.

1

Press GEQ FREQ (LOW).

The lowest level frequency indicator flashes for 8 seconds.

2

Within 8 seconds, turn MULTI JOG to adjust the

level of the lowest frequency.

3

Press GEQ FREQ (HIGH).

The highest level frequency indicator flashes for 8 seconds.

4

Within 8 seconds, turn MULTI JOG to adjust the

level of the highest frequency.

The frequency level indicators between the lowest and the

highest are adjusted accordingly.

ROCK

POP

LATIN

Program mode

CLASSIC

GEQ M5 GEQ M1

Manual mode

GEQ M2GEQ M3GEQ M4

JAZZ

GEQ

MULTI

JOG

f,g

GEQ FREQ

(HIGH)

GEQ FREQ

(LOW)

MULTI

JOG

ENGLISH

13

En

MEMORIZING THE NEW EQUALIZATION

CURVES

Up to 5 customized equalization curves can be stored on the

manual mode M1-M5.

1

Set a new equalization curve with GEQ FREQ and

MULTI JOG.

See “SETTING A NEW EQUALIZATION CURVE MANUALLY”

on page 12.

The created equalization curve is displayed for 8 seconds.

2

Within 8 seconds, press ENTER.

“GEQ M1” is displayed and all the manual mode indicators

flash for 8 seconds. Go to step 3 within those 8 seconds.

• If this step is not completed within 8 seconds, press GEQ

FREQ first to display “GEQ HIGH” or “GEQ LOW”. Then

press ENTER within 8 seconds.

3

While the manual mode indicators are flashing,

turn MULTI JOG to select a number among from

M1 to M5 and press ENTER.

The equalization curve is stored.

To select the stored equalization curve

1 Press GEQ.

2 Within 4 seconds, turn MULTI JOG to select a desired number

among from M1 to M5.

SOUND

DSP SURROUND

The DSP (Digital Signal Processor) SURROUND system can

create the effect of sound reflected from walls and ceilings. This

system enhances 5 types of sound presence.

DISCO: Sound presence of a disco

LIVE: Sound presence of a live music performance

STADIUM: Sound presence of a stadium

HALL: Sound presence of a concert hall

MOVIE: Sound presence of a movie theater

1

Press SURROUND.

The current mode is displayed.

2 Within 4 seconds, turn MULTI JOG or press f

or g to select a desired mode.

Equalization curves are selected automatically to match the DSP

SURROUND modes and can also be selected or turned off to

suit your preference.

When the music source is monaural

Select LIVE, STADIUM or MOVIE to obtain a simulated stereo

effect. When DISCO or HALL is selected, no sound will be heard

from the surround speakers.

To cancel the selected mode

Press SURROUND twice so that “DSP OFF” is displayed. The

selected equalization curve remains.

To adjust the volume of the surround speakers

Press MANUAL SELECT twice or three times on the remote

control. “S-L” or “S-R” is displayed for 2 seconds. Press f or

g on the remote control within these 2 seconds.

• The DOLBY PRO LOGIC (page 23) and the DOLBY DIGITAL

SURROUND (page 25) surround speakers level is also

changed.

NOTE

The DSP SURROUND mode is canceled when:

- the ECHO is turned on.

- the DOLBY PRO LOGIC is turned on.

- the headphones are plugged in.

- the 5.1CH (page 25) is selected.

GEQ FREQ

MULTI JOG

ENTER

SURROUND

f,g

MANUAL

SELECT

SURROUND

14

ENGLISH

MANUAL TUNING

1

Press TUNER/BAND repeatedly to select the FM

or AM band.

When TUNER/BAND is pressed while the power is off, the

power is turned on directly (Direct Play Function).

2

Press TUNER PRESET repeatedly to select the

manual tuning mode.

Each time the button is pressed, the following three tuning

modes are selected cyclically.

1 Preset tuning mode: The preset number flashes.

2 Auto search mode: “SEARCH” is displayed.

3 Manual tuning mode: “SEARCH” is not displayed and

the preset number does not flash.

NOTE

The preset tuning mode is skipped if no station is preset.

3

Turn MULTI JOG clockwise or counterclockwise

to tune in to a station.

The frequency changes as you turn MULTI JOG.

When a station is received, “TUNE” is displayed for 2 seconds.

During FM stereo reception, 1 is displayed.

• fDOWN and gUP are also available to tune in to a

station.

To search for a station quickly (Auto Search)

Press TUNER PRESET repeatedly to display “SEARCH” (auto

search mode), and turn MULTI JOG clockwise or

counterclockwise until the frequency starts to change rapidly.

After tuning in to a station, the search stops.

To stop the Auto Search manually, turn MULTI JOG a little in

either direction.

• The Auto Search may not stop at stations with very weak

signals.

• fDOWN and gUP are also available to search for a

station. Keep fDOWN or gUP pressed until the tuner

starts searching. Press the button to stop the search manually.

When an FM stereo broadcast contains noise

Press MONO TUNER on the remote control so that “MONO”

appears on the display.

Noise is reduced, although reception is monaural.

To restore stereo reception, press MONO TUNER so that

“MONO” disappears and “STEREO” is displayed for 2 seconds.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If

you use this unit in an area where the frequency allocation system

is 9 kHz/step, change the tuning interval.

Press POWER while pressing TUNER/BAND on the unit.

To reset the interval, repeat this procedure.

Preset

number

RADIO RECEPTION

SEARCH

Frequency

SEARCH

MONO

1

TUNER/

BAND

POWER

TUNER

PRESET

MULTI

JOG

f,g

MONO

TUNER

TUNER/

BAND

ENGLISH

15

En

PRESETTING STATIONS

The unit can store a total of 32 preset stations for all bands.

When a station is stored, a preset number is assigned to the

station. Use the preset number to tune in to a preset station

directly.

1

Press TUNER/BAND to select a band, and tune in

to a station with fDOWN or gUP.

2

Press aSET to store the station.

A preset number beginning from 1 in consecutive order for

each band is assigned to a preset station.

3

Repeat steps 1 and 2.

No more stations will be stored if a total of 32 preset stations

have already been stored.

NOTE

• When the AM tuning interval is changed, all preset stations are

cleared. The preset stations have to be set again.

•“FULL” is displayed if you attempt to store more than 32 preset

stations.

PRESET NUMBER TUNING

Use the remote control to select the preset number directly.

1

Press TUNER/BAND to select a band.

2

Press numbered buttons 0-9 and +10 to select a

preset number.

Example:

To select preset number 20, press +10, +10 and 0.

To select preset number 15, press +10 and 5.

Selecting a preset number on the main unit

Press TUNER/BAND to select a band.

Press TUNER PRESET repeatedly until the preset number

flashes (preset tuning mode), and turn MULTI JOG. The preset

numbers are selected in sequence as you turn MULTI JOG.

• dPRESET is also available to select the preset number.

Each time the button is pressed, the next highest number is

selected.

To clear a preset station

Select the preset number of the station to be cleared with the

numbered buttons. Then, press sCLEAR, and press aSET

within 4 seconds.

The preset numbers of all other stations in the band with higher

numbers are decreased by one.

Frequency

RADIO RECEPTION

TUNER/

BAND

a

f,g

TUNER/

BAND

f,g

TUNER/

BAND

MULTI

JOG

a

s

a

s

c/d

d

TUNER/

BAND

0-9,+10

TUNER

PRESET

16

ENGLISH

BASIC OPERATIONS

1 Press DOLBY NR to turn Dolby NR on or off to

match the playback tape.

For tapes recorded with DOLBY NR, turn on hNR.

For tapes recorded without DOLBY NR, turn off hNR.

2 Press TAPE and press zTAPE OPEN/CLOSE to

open the cassette tray.

Load a tape with the exposed side facing the unit, and the

side to be played back facing upward.

3 Press zTAPE OPEN/CLOSE to close the cassette

tray.

4 Press d to start play.

To play the opposite side of the tape, press d again.

x: The side facing upward is being played (forward).

c: The opposite side is being played (reverse).

TAPE PLAYBACK

The tape counter indicates the tape

running length.

Playback

side indicator

To stop play, press s.

To pause play, press a. To resume play, press again.

To fast forward or rewind, press f or g. Then press s

to stop the tape.

Types of tape

Use Type I (normal), Type II (high/CrO2) or Type IV (metal) tapes

for playback.

To select a reverse mode

Each time REV MODE is pressed, the reverse mode changes.

To play one side only, select p.

To play from the side facing upward to the opposite side once

only, select .

To play both sides repeatedly, select ].

To start play when the power is off (Direct Play Function)

When a tape is loaded, press TAPE. The power is turned on

and playback begins.

When zTAPE OPEN/CLOSE is pressed, the power is also

turned on.

To set the tape counter to “0000”

Press sCLEAR in stop mode.

The counter is also set to “0000” when the cassette tray is

opened.

MUSIC SENSOR

If there is a 4-second or longer blank between each track, a

search for the beginning of the current or next track during

playback can be done easily.

When the x indicator of d is flashing, press f to move

to the next track or g to move to the beginning of the current

track.

When the c indicator of d is flashing, press g to move

to the next track, or f to move to the beginning of the current

track.

The search function may not be able to detect tracks under the

following conditions:

• Blanks of less than 4 seconds between tracks

• Noisy blanks

• Long passages of low-end sound

• Low overall recording levels

DOLBY NR

Cassette

tray

REV MODE

zTAPE

OPEN/

CLOSE

TAPE

a

f,g

s

jl

hNR

Cassette tape

zTAPE OPEN/CLOSE

[

]

P

ENGLISH

17

En

BASIC OPERATIONS

LOADING DISCS

Press CD, then press zCD OPEN/CLOSE to open

the disc compartment. Load disc(s) with the label

side up.

To load one or two discs, place the discs tray 1 and tray 2.

To load three discs, press DISC CHANGE to rotate the trays

after placing two discs. Place the third disc on tray 3.

After placing the discs, press zCD OPEN/CLOSE to close

the disc compartment.

The display shows the information of the disc to be played.

Tray number of the disc to be played

Total number of tracks

Total playing time

CD PLAYING

CD PLAYING TAPE PLAYBACK

CD

zCD OPEN

/CLOSE

DISC

CHANGE

PLAYING DISCS

Load discs.

To play all discs in the disc compartment (continuous

play), press d.

Play begins with the disc on tray 1.

The indicator of DISC DIRECT PLAY flashes to indicate the disc

being played.

To play one disc only (single disc play), press one of

DISC DIRECT PLAY 1-3.

The disc with the selected tray number is played once.

Only the indicator of the selected DISC DIRECT PLAY flashes.

To play with the remote control

Press DISC DIRECT PLAY, then press one of the numbered

buttons 1-3 within 3 seconds to select a disc.

To stop play, press s.

To pause play, press a. To resume play, press again.

To search for a particular point during playback, keep f

or g pressed and release the button at the desired point.

To skip to the beginning of a track during playback, turn

MULTI JOG or press f or g repeatedly.

To remove discs, press zCD OPEN/CLOSE.

You can only remove the two discs that face you. When the

disc(s) to be removed does(do) not face you, press DISC

CHANGE repeatedly.

Number of track

being played

Elapsed playing time

Selected

disc tray

number

Elapsed playing time

Number of track

being played

dDIRECTION/

PRESET

MULTI

JOG

DISC

DIRECT PLAY

DISC

DIRECT

PLAY

s

c/d

CD EDIT/

CHECK

0-9,+10

CD

f,g

zCD

OPEN/

CLOSE

18

ENGLISH

To start play when the power is off (Direct Play Function)

Press CD. The power turns on and play of the loaded disc(s)

begins.

When z CD OPEN/CLOSE is pressed, the power is also turned

on and the disc compartment is opened.

To check the remaining time

Press CD EDIT/CHECK on the remote control during play. The

amount of time remaining until all tracks finish playing is

displayed. To restore the playing time display, press CD EDIT/

CHECK.

Selecting a track with the remote control

1 Press DISC DIRECT PLAY, then press one of the numbered

buttons 1-3 within 3 seconds to select a disc.

2 Press the numbered buttons 0-9 and +10 to select a track.

Example:

To select the 25th track, press +10, +10 and 5.

To select the 10th track, press +10 and 0.

The selected track starts to play and play continues to the

end of that disc.

Replacing discs during play

While one disc is playing, the other discs can be replaced without

interrupting play.

1 Press DISC CHANGE.

2 Remove the discs and replace with other discs.

3 Press zCD OPEN/CLOSE to close the disc compartment.

NOTE

• When loading an 8-cm (3-inch) disc, make sure to place it onto

the inner circle of the tray precisely.

• Do not place more than one compact disc on one disc tray.

• Do not tilt the unit with discs loaded. Doing so may cause

malfunctions.

• Do not use irregular shape CDs (

example:

heart-shaped,

octagonal ones). It may result in malfunctions.

• The unit may not play a CD-R/RW disc that is recorded on

personal computers or some kinds of CD-R/RW recorders

because of differences in recording platforms.

• Do not attach any seal or label to either side (the recordable

side or the labeled side) of a CD-R/RW disc. It may cause

malfunction.

RANDOM/REPEAT PLAY

Use the remote control.

RANDOM PLAY

All the tracks on the selected disc or all the discs can be played

randomly.

REPEAT PLAY

A single disc or all the discs can be played repeatedly.

Press RANDOM/REPEAT.

Each time it is pressed, the function can be selected cyclically.

RANDOM play — The line around RANDOM lights up on the

display.

REPEAT play —

"

lights up on the display.

RANDOM/REPEAT play — The line around RANDOM and

"

light up on the display.

Cancel — The line around RANDOM and

"

disappear from

the display.

To play all discs, press d to start play.

To play a single disc, press DISC DIRECT PLAY, then press

one of the numbered buttons 1-3 within 3 seconds to start play.

NOTE

• During random play, it is not possible to skip to the previously

played track with f or MULTI JOG.

• Random play is canceled when the numbered button is pressed

to select a track.

RANDOM/REPEAT

ENGLISH

19

En

PROGRAMMED PLAY

Up to 30 tracks can be programmed from any of the inserted

discs.

Use the remote control.

1

Press PRGM twice in stop mode.

“– –” and the line of PRGM appear on the display.

• When PRGM is pressed once in step 1, the unit enters the

CD KARAOKE PROGRAM (page 28).

2

Press DISC DIRECT PLAY, then press one of the

numbered buttons 1-3 within 3 seconds to select

a disc.

Go to the next step when the tray stops rotating.

3

Press the numbered buttons 0-9 and +10 to

program a track.

Example:

To select the 25th track, press +10, +10 and 5.

To select the 10th track, press +10 and 0.

4

Repeat steps 2 and 3 to program other tracks.

5

Press d to start play.

Program number

Selected track

number

Total number of

selected tracks

Total playing

time of the

selected tracks

To check the program

Each time f or g is pressed in stop mode, a disc number,

track number, and program number will be displayed.

To clear the program

Press sCLEAR in stop mode.

To add tracks to the program

Repeat steps 2 and 3 in stop mode. The track will be programmed

after the last programmed track.

To change the programmed tracks

Clear the program and repeat all the steps again.

To play the programmed tracks repeatedly

After programming the tracks, press RANDOM/REPEAT once

so that

"

appears on the display.

NOTE

• During programmed play, you can not use random play or check

the remaining time.

• During programmed play, you can not select a track. “Can’t

USE” is displayed if you attempt to select a track.

•“FULL” is displayed if you attempt to program more than 30

tracks.

BLANK SKIP PLAY

The silent portions between tracks recorded on a CD can be

skipped during playback.

1

Press CD BLANK SKIP on the main unit.

“CD BLANK SKIP ON” is displayed and a blank skip mark will

appear in the display.

2

Press d to start playback.

The silent portions between tracks will be skipped, and the

sound will be played back without interruption. If a track fades

out (ends with the sound gradually decreasing), the fadeout

portion will also be skipped.

To return to normal playback

Press CD BLANK SKIP again. “CD BLANK SKIP OFF” is

displayed and the blank skip mark in the display will disappear.

NOTE

• There may be a case where BLANK SKIP PLAY does not

function correctly.

• BLANK SKIP PLAY is automatically canceled when performing

AI EDIT RECORDING (page 21), PROGRAMMED EDIT

RECORDING (page 22), or recording during PROGRAMMED

PLAY (left column) or RANDOM PLAY (page 18).

PRGM

CD PLAYING

RANDOM/REPEAT

s

c/d

PRGM

0-9,+10

f,g

DISC

DIRECT

PLAY

Blank skip mark

La page charge ...

Aiwa XH-A1000 Operating Instructions Manual

Aiwa XH-A1000 Operating Instructions Manual

dans d''autres langues

Documents connexes

Autres documents