Garland MST54 Owner Instruction Manual

Marque: Garland

Modèle: MST54

Catégorie: Cuisinières

Taper: Owner Instruction Manual

Part # 4515576 Rev 2 (01/15/16)

Master Series

Infra-Red & Ceramic Broilers

Installation, Operation and Maintenance Manual

Original Instructions

models

M60XR

M60XRC

M60XS

M60XT

M100XR

M100XRC

M100XS

M100XT

M110XM

Part # 4515576 Rev 2 (01/15/16)Page 2

IMPORTANT INFORMATION

WARNING:

This product contains chemicals known to the state of California to cause cancer and/or birth defects

or other reproductive harm. Installation and servicing of this product could expose you to airborne

particles of glass wool/ceramic fibers. Inhalation of airborne particles of glass wool/ceramic fibers

is known to the state of California to cause cancer. Operation of this product could expose you to

carbon monoxide if not adjusted properly. Inhalation of carbon monoxide is known to the state of

California to cause birth defects or other reproductive harm.

Keep appliance area free and clear of combustibles.

Users are cautioned that maintenance and repairs must be performed by a Garland authorized service agent

using genuine Garland replacement parts. Garland will have no obligation with respect to any product that has been

improperly installed, adjusted, operated or not maintained in accordance with national and local codes or installation

instructions provided with the product, or any product that has its serial number defaced, obliterated or removed,

or which has been modified or repaired using unauthorized parts or by unauthorized service agents.

For a list of authorized service agents, please refer to the Garland web site at http://www.garland-group.com.

The information contained herein, (including design and parts specifications), may be superseded and is subject

to change without notice.

FOR YOUR SAFETY:

DO NOT STORE OR USE GASOLINE

OR OTHER FLAMMABLE VAPORS OR

LIQUIDS IN THE VICINITY OF

THIS OR ANY OTHER

APPLIANCE

WARNING:

IMPROPER INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR MAINTENANCE

CAN CAUSE PROPERTY DAMAGE, INJURY,

OR DEATH. READ THE INSTALLATION,

OPERATING AND MAINTENANCE

INSTRUCTIONS THOROUGHLY

BEFORE INSTALLING OR

SERVICING THIS EQUIPMENT

PLEASE READ ALL SECTIONS OF THIS MANUAL

AND RETAIN FOR FUTURE REFERENCE.

THIS PRODUCT HAS BEEN CERTIFIED AS

COMMERCIAL COOKING EQUIPMENT AND

MUST BE INSTALLED BY PROFESSIONAL

PERSONNEL AS SPECIFIED.

IN THE COMMONWEALTH OF MASSACHUSETTS

THIS PRODUCT MUST BE INSTALLED BY A

LICENSED PLUMBER OR GAS FITTER.

For Your Safety:

Post in a prominent location, instructions to be

followed in the event the user smells gas. This

information shall be obtained by consulting

your local gas supplier.

Part # 4515576 Rev 2 (01/15/16) Page 3

TABLE OF CONTENTS

IMPORTANT INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Technical Speci cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Electrical Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Individual Burner Input Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Model Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

STATUTORY REGULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Siting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Ventilation Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Gas Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Installation Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Installing Ceramic Radiants (model M60XR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Appliances Equipped With Casters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Appliances Equipped With Legs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Testing & Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

FDO Heavy Duty Oven control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Broiler Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Cast Iron Burner With Ceramic Tile - M60X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Infra-Red Burners -M100XM, M110XM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Standard Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Convection Ovens (RC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PRODUCT APPLICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Broiler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Convection Ovens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

CARE & CLEANING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Stainless Steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Oven Interior (Porcelain Enamel) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Broiler Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

General Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

M110XM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

M100X (R/RC/S/TM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Instructions For Removal Of Grid Rack &

Grid Rack Frame. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Part # 4515576 Rev 2 (01/15/16)Page 4

SPECIFICATIONS

Technical Speci cations

MINIMUM SUPPLY

PRESSURE

MANIFOLD

OPERATING PRESSURE

Natural Gas: 7” w.c. Natural Gas: 6” w.c.

Propane: 11” w.c. Propane: 10” w.c.

Electrical Supply

120V 60Hz, 1A – Infra-Red Burner Models.

120V 60Hz, 4.4A - Models with Infra-Red Burners and a

Convection Oven Base.

Individual Burner Input Ratings

Natural Gas

Burner

Input BTU/Hr

per Section

Ori ce Size

DMS

Cast Iron Burner With

Ceramic Tile

80,000 # 35

Infra-Red 70,000 # 50

Oven 40,000 # 33

Propane

Burner

Input BTU/Hr

per Section

Ori ce Size

DMS

Cast Iron Burner With

Ceramic Tile

80,000 # 48

Infra-Red 70,000 # 56

Oven 35,000 # 50

Model Designations

Model

Number

Broiler Burner Base

M60XR Cast Iron Burner With

Ceramic Tile

Standard Oven

M60XRC Cast Iron Burner With

Ceramic Tile

Convection Oven

M60XS Cast Iron Burner With

Ceramic Tile

Storage

M60XT Cast Iron Burner With

Ceramic Tile

Counter Top or

Modular Stand

M100XR Infra-Red Standard Oven

M100XRC Infra-Red Convection Oven

M100XS Infra-Red Storage

M100XT Infra-Red Counter Top or

Modular Stand

M110XM Infra-Red —

Clearances

INSTALLATION CLEARANCES

Model Number Sides Rear

M60XR 6” (152mm) 6” (152mm)

M60XRC 6” (152mm) 6” (152mm)

M60XS 6” (152mm) 6” (152mm)

M60XT 6” (152mm) 6” (152mm)

M100XR 6” (152mm) 6” (152mm)

M100XRC 6” (152mm) 6” (152mm)

M100XS 6” (152mm) 6” (152mm)

M100XT 6” (152mm) 6” (152mm)

M110XM 6” (152mm) 6” (152mm)

Part # 4515576 Rev 2 (01/15/16) Page 5

GENERAL INFORMATION

1. Check crate for possible damage sustained during transit.

Carefully remove unit from crate and again check for

damage. Any damage to the appliance must be reported

to the carrier immediately.

2. The wires for retaining the burners and other packing

material must be removed from units. Any protective

material covering stainless steel parts must also be

removed.

3. All equipment is shipped from the factory with legs

 tted, unless otherwise speci ed. Where the range is to

be mounted on a dais or cove base, it is shipped without

legs. Legs must be  tted to the oven where it is installed

on a combustible  oor.

4. The type of gas and supply pressure that the equipment

was set-up for at the factory is noted on the data plate

and on the packaging. This type of gas supply must be

used.

5. Garland/U.S. Range products are not approved or

authorized for home or residential use, but are intended

for commercial applications only. Garland / U.S. Range

will not provide service, warranty, maintenance

or support of any kind other than in commercial

applications.

6. Do not remove permanently a xed labels, warnings or

data plates from the appliance, for this may invalidate the

manufacturer’s warranty.

STATUTORY REGULATIONS

The installation of this appliance must be carried out by

a competent person and in accordance with the relevant

regulations, codes of practice and the related publications of

the country and destination.

The installation must conform to the National Fuel Gas Code

ANSI Z223.1-latest edition, NFPA No. 54 – latest edition and

National Electrical Code ANSI/NFPA 70-latest edition and/or

local code to assure safe and e cient operation. In Canada,

the installation must comply with CSA B149.1 and local

codes where applicable.

In Canada, electrical connections must comply with

applicable sections of the Canadian Electrical Code, C22.1 -

latest edition.

Part # 4515576 Rev 2 (01/15/16)Page 6

INSTALLATION

Siting

The  oor on which the appliance is to be sited must be

capable of adequately supporting the weight of the

appliance and any ancillary equipment.

Units with ovens must be  tted with legs if installed on a

combustible  oor.

Ventilation Air

The following notes are intended to give general guidance.

For detailed recommendations, refer to the applicable

code(s) in the country of destination.

Proper ventilation is highly essential for optimum

performance. The ideal method of ventilating open-top

equipment is the use of a properly designed canopy which

should extend six inches (152mm), beyond all sides of the

appliance(s) and six feet, six inches (1981mm) above the

 oor.

A strong exhaust will create a vacuum in the room. For an

exhaust vent to work properly, replacement air must enter

the room. The amount of air that enters must be equal to the

amount exhausted.

All gas burners and pilots need su cient air to operate. Large

objects should not be placed in front of the appliance(s) that

would obstruct the  ow of air into the front.

Gas Connection

The local gas authority should be consulted at the

installation planning stage in order to establish the

availability of an adequate supply of gas and to ensure

that the meter is adequate for the required  ow rate. The

pipe work from the meter to the appliances must be of an

appropriate size.

All  xed (non-mobile) appliances MUST be  tted with a

manual gas-cock upstream of the appliance to provide a

means of isolation for servicing or cleaning purposes. A

union or similar means of disconnection must be provided

between the gas-cock and the appliance.

A manually operable valve must be  tted to the gas supply

to the kitchen to enable it to be isolated in an emergency.

Wherever practical, this shall be located either outside the

kitchen or near to an exit in a readily accessible position.

Where it is not practical to do this, an automatic isolation

valve system shall be  tted which can be operated from a

readily accessible position near to the exit.

At locations where the manual isolation valve is  tted or

the automatic system can be reset, a notice MUST be  tted

stating:

“ALL DOWNSTREAM BURNER AND PILOT VALVES MUST

BE TURNED OFF PRIOR TO ATTEMPTING TO RESTORE THE

SUPPLY. AFTER EXTENDED SHUT OFF, PURGE BEFORE

RESTORING GAS SUPPLY.”

Electrical Connection

(Models with Infra-Red Burners and/or Convection Oven

Bases)

IMPORTANT – This appliance must be electrically grounded

in accordance with local codes.

Installation Notices

Before assembly and connection check gas supply.

A. The type of gas for which the unit is equipped is stamped

on the data plate located behind the lower front panel.

Connect a unit stamped “NAT” only to natural gas;

connect one stamped “PRO” only to propane gas.

B. If it is a new installation have the gas authorities check

the meter size and piping to assure that the unit is

supplied with the necessary amount of gas pressure

required for operation.

C. If it is additional or replacement equipment have the

gas authorities check the pressure to make certain that

existing meter and piping will supply fuel to the unit with

no more than 1/2” water column pressure drop.

D. Legs must be  tted to the oven where it is installed on a

combustible  oor.

E. When installed without legs on a non-combustible curb

or plateform, the front of the unit should extend at least 3

inches or 76 mm such that the air vent is not blocked.

NOTE: When checking gas pressure be sure that all other

equipment on the same gas line is on.

The appliance and its individual shut-o valve must be

disconnected from the gas supply piping system during any

pressure testing of that system with pressures in excess of

1/2 PSIG (3.45kPa).

Adequate clearance must be provided for servicing and

proper operation.

THIS APPLIANCE IS NOT RECOMMENDED FOR RESIDENTIAL

INSTALLATION.

Part # 4515576 Rev 2 (01/15/16) Page 7

Installing Ceramic Radiants (model M60XR)

iii

View: Looking into the front of broiler section.

i. Center Support ii. Ceramic Radiants iii. Side Support Rails iv. Burners

1. Pull forward the broiler rack of the ceramic broiler

section. Lift out rack insert and remove grease deflector

pan beneath rack assembly by raising it off the shoulder

bolts at the rear of the rack front plate.

2. Lower rack raising mechanism to its lowest position and

tie or wire the raising arm in place to avoid premature

release of the raising mechanism.

3. Start with the left side. Projections of the ceramic

radiants, will be down and the groove of the ceramic

radiants will be toward the center of the unit (See

sketch). Tilt the ceramic radiant to permit it to clear both

the side support and the center support and raise the

radiant above these 2 supports. Fit the groove of the

ceramic radiant into the flange of the center support

and lower its outer edge to rest on the top of the side

support. Slide this ceramic radiant to the rear and

repeat this with the two remaining ceramic radiants

overlapping.

4. Installation of the ceramic radiants on the right side is

similar to that as described above, except that you will

start from the front and work toward the rear. It may be

necessary to tilt the adjacent ceramic radiant upward

slightly to permit the interlocking of the final ceramic

radiants.

5. When all radiants have been installed, slide them as far

as possible to provide for proper flue movement.

Appliances Equipped With Casters

1. The installation shall be made with a connector that

complies with the Standard for Connectors for Moveable

Gas Appliances, ANSI Z21.69/CSA 6.16, Addenda

Z21.69B-2006/CSA 6.16B-2006 (or latest edition), and a

quick-disconnect device that complies with the Standard

for Quick Disconnects for Use with Gas Fuel, ANSI Z21.41/

CSA 6.9, Addenda Z21.41A-2005/CSA 6.16A-2005 (or

latest edition).

INSTALLATION Continued

2. The front casters on the appliance are equipped with

brakes to limit the movement of the appliance without

placing any strain on the connector or quick-disconnect

device or its associated piping.

3. Please be aware that the required restraint is attached to

a bracket (which is located on the rear caster closest to

the gas connection) and if disconnection of the restraint

is necessary, be sure to reconnect the device after the

appliance has been returned to its original position.

Appliances Equipped With Legs

1. Raise the front of the appliance an block. Do not lay the

appliance on its back.

2. Position leg insert in leg retainer opening and tap upward

until the insert seats at the collar  ange.

3. Repeat leg insert installation for the other legs and adjust

all four legs to the same height.

4. Legs can be further adjusted to level the appliance and to

compensate for uneven  ooring.

Testing & Adjustment

All  ttings and pipe connections must be tested for

leaks. Use approved gas leak detectors, soap solution or

equivalent, checking over and around all the  ttings and

pipe connections. DO NOT USE A FLAME! Accessibility to

all gas lines and  ttings require that valve panel(s), lower

front panel(s), and/or oven rack(s) be removed. It may be

necessary to remove, or at least raise and securely prop

griddles, hot top, and/or top grates. All parts removed,

(including fasteners), should be stored safely for re-

installation.

1. Be sure that all valves and thermostats are in the “OFF”

position.

2. Turn on the main gas supply valve. Light all broiler pilots.

3. Leak test all valves and  ttings as described at the

beginning of this section. Correct any leaks as required

and recheck.

4. Light the oven pilot.

5. If the range is equipped with an oven on/o valve

separate from the thermostat, turn this valve on. If

the oven thermostat dial has an “OFF” position the

thermostat is its own on/o valve.

6. In either case, now set the thermostat to 500°F (260°C).

Leak test all valves and  ttings as described at the

beginning of this section. Correct any leaks as required

and recheck.

Part # 4515576 Rev 2 (01/15/16)Page 8

7. Shut o all valves and set thermostat dials to “OFF” or

lowest position.

All units are tested and adjusted at the factory, however,

burners and pilots should be checked upon installation and

adjusted if necessary.

CAUTION: Gas will  ow to the top section burners even

if the broiler section pilots are not lit. Gas will not be

interrupted. It is the responsibility of the operator to

con rm the proper ignition of each burner as it is turned

on. Should ignition fail to occur 5 seconds after turning

a burner on, turn the burner o , wait 5 minutes, and try

again.

FDO Heavy Duty Oven control

The model FDO oven thermostat is a precision-made

instrument, carefully set at the factory to accurately control

oven temperatures from 150° to 500°F, (66° to 260°C). All

adjustments are accessible from the front of the appliance

after moving the dial. To remove the dial, grasp the outer

edges and pull straight out.

By-Pass Adjustment

The Robertshaw FDO snap/throttle thermostat requires that

the by-pass  ame be properly adjusted. To adjust proceed as

follows:

Calibration

Lock Screws

By-pass Flame

Adjuster

Indicator Mark

Calibration

Plate

Dial

Stop

MODEL

FDO

1. Ensure pilot  ame is lit and adjusted.

2. Turn oven temperature control to 200°F, (93°C), and allow

the oven to heat for three minutes.

3. Turn, the oven temperature control to the lowest

position, then turn slowly counter-clockwise until the

audible “click” is heard.

4. Making sure the oven temperature control dial is not

disturbed, turn the by-pass  ame adjusting screw

clockwise to decrease, or counter-clockwise to increase

the  ame on the burner to the lowest possible stable

 ame. When properly adjusted, the by-pass  ames will

cover the entire length of the burner.

Calibration Instructions

Field calibration is seldom necessary and should not

be resorted to unless experience with cooking results

undoubtedly indicate that the control is not maintaining

the temperature for which the dial is set. To check oven

temperatures when calibrating, use only a reliable mercury

thermometer, or preferably an oven pyrometer. To check

calibration, proceed as follows:

1. Place the thermocouple of the test instrument or reliable

mercury thermometer in the center of the oven.

2. Turn the oven temperature control knob to 400°F, (204°C),

and allow the oven to cycle at least three times.

3. Continue to monitor the oven temperature, recording

the readings at 5 minute intervals until three successive

readings are within 5°F, (2°C), of each other.

If the temperature does not read within 15°F, (8°C), of the dial

setting, recalibrate as follows.

1. Remove the oven temperature control dial, making sure

the setting is not disturbed.

2. Hold the calibration plate, (located directly behind the

control dial), and loosen the two calibration lock screws

until the plate can be rotated independently of the

control.

3. Turn the calibration plate until the temperature indicated

on the plate corresponds with the reading on the test

instrument. Hold the plate in place and tighten the

screws  rmly.

4. Repeat step 3 in the previous section, checking the

temperature to ensure the adjustment has been made

properly.

5. Replace the temperature control dial.

NOTE: If adjustment of the calibration plate is prevented by

the position of the lock screws, the screws can be moved to

other holes that have been tapped for them.

INSTALLATION Continued

Part # 4515576 Rev 2 (01/15/16) Page 9

OPERATION

Broiler Section

Cast Iron Burner With Ceramic Tile - MX

Initial Operation:

When all gas connections have been inspected, proceed as

follows to put the unit into operation:

1. Open gas service valve located in your supply line.

2. With a lighted taper, light the broiler pilots located at the

front of the unit. There is one pilot per burner.

3. Pilot adjustment valves can be found on the manifold,

behind the control panel. The valves may be accessed

through holes in the control panel.

4. The pilot  ame should be adjusted to provide a  ame

7/8”(22mm) to 1”(25mm) in length.

Operation:

1. Turn the broiler valve to HIGH.

2. Immediately check ignition of the burners.

3. When ignition has been accomplished a blue  ame will

cover the length of the burner.

4. Flames will  ow upward over ceramic radiant bricks and

will glow red.

Shut-Down:

1. Turn all valves to the “OFF” position.

2. If the unit is to be shut down for an extended period of

time, close the in-line gas valve.

Infra-Red Burners -MXM, MXM

The GARLAND® Infra-Red Broiler is a direct radiant heavy

duty gas broiler utilizing four (4) extremely e cient gas

burners in each broiling section. The infra-red burners

provide for high speed broiling with rapid searing of product

so that natural juices and  avor will be sealed in.

These special burners operate in a manner similar to that

of a conventional gas burner except that the radiation

surfaces consist of a series of ceramic blocks each containing

numerous small gas ports. These ceramic blocks are

connected utilizing a special compound that also seals all

seams of the radiating surface. The gas  ame appears as a

red glow covering the entire ceramic surface.

A special wire mesh has been provided as an outside

surface beneath the ceramics to further increase the burner

e ciency. This mesh will provide for additional infra-red

energy.

Initial Operation:

1. Connect electrical supply.

2. Open gas service valve located in your supply line.

3. With a lighted taper, light the broiler pilots located at the

front of the unit. There is one pilot per pair of burners.

4. Pilot adjustment valves can be found on the manifold,

behind the control panel. The valves may be accessed

through holes in the control panel.

5. The pilots should be adjusted so that  ame extends 1/2”

to 3/4” (12mm to 25mm) beyond the pilot shield.

Operation:

1. Switch on (1) the main power switch.

2. Turn the broiler valve to HIGH.

3. Immediately check ignition of the burners.

4. When ignition has been accomplished a blue  ame will

cover the surface of the ceramics for 10-15 seconds.

5. The haze will disappear and the ceramics will glow red.

Shut-Down:

1. Turn all valves to the “OFF” position.

2. Switch o (0) the main power switch.

3. If the unit is to be shut down for an extended period of

time, close the in-line gas valve.

Part # 4515576 Rev 2 (01/15/16)Page 10

CAUTION: Should burner ignition fail within 5 seconds,

turn the burner valve o and repeat steps 1 through 5. If

ignition continues to fail, consult your factory authorized

service agency.

Ovens

Standard Ovens

Lighting:

1. Push in the main / pilot gas valve and turn it counter-

clockwise to the IGNITION position.

2. Lower the front kick panel.

3. Holding the oven gas valve fully in, press the red piezo

igniter button several times.

4. When the pilot burner is lit, continue holding in the oven

gas valve for 20 seconds, then release it. If the pilot goes

out, wait  ve minutes and try again.

5. When the pilot  ame is established, push the gas

valve in again and turn it counter-clockwise to the full

ON position, then set the thermostat to the desired

temperature.

Shut-Down:

1. Turn all valves to the OFF position and the safety device

will disengage within 60 seconds.

2. If the unit is to be shut down for an extended time, close

the in-line gas valve.

Re-lighting:

1. Turn all gas valves o .

2. Wait  ve minutes.

3 Follow procedure under “Lighting” at left.

OPERATION Continued

Convection Ovens (RC)

Lighting:

Same as standard oven.

Start-Up:

1. Activate the power switch to COOK position.

2. Turn oven valve ON.

3. Turn thermostat to desired setting.

Cool Down:

1. Turn thermostat and oven valve OFF.

2. Open door.

3. Activate power to the COOL DOWN position.

The motor on your range convection oven is maintenance

free since it is constructed with self-lubricating sealed ball

bearings. It is designed to provide durable service when

treated with ordinary care. We have a few suggestions to

follow on the care of your motor.

A When the motor is operating, it cools itself internally by

air entering the rear of the motor case, provided proper

clearance has been allowed.

B. Since the blower wheel is in the oven cavity it is at the

same temperature as the oven. If the motor is stopped

while the oven is hot, the heat from the blower wheel is

conducted down the shaft and into the armature of the

motor. This action could shorten the motor life.

C. We recommend, at the end of the bake or roasting

period, when the oven will be idle for any period of time

or before shutting down completely, that the doors be

left open, and by use of the cool down position on the fan

switch, the fan continues to run for at least 20 minutes.

Note: The convection oven motor should never be turned

“OFF” during cooking or when the oven is “HOT”.

Part # 4515576 Rev 2 (01/15/16) Page 11

PRODUCT APPLICATION

Broiler

The following information is intended for use as a guide.

There are many variables that will e ect the operation. As an

example, the temperature of the product when it is placed

on the rack for broiling will e ect both the broiling time and

the quality of the  nished product.

The broiler rack can be easily raised or lowered to provide for

the desired distance of the product from the heat source and

is readily pulled out for ease of loading and unloading.

It is suggested that all products be dipped in salt-free

oil before broiling to facilitate browning and to aid in

preventing the product from sticking to the broiler rack.

It must again be stressed that the times above are intended

as a general guide only. The technique of the operator and

experience with infra-red broiling will e ect time, burner

setting and rack position.

SUGGESTED BROILING TIME (EACH SIDE) IN MINUTES

Type of Product Thickness “

(mm)

Rare

Minutes

Medium

Minutes

Well Done

Minutes

Beef

Filet Mignon, Porterhouse 1 (25) 2 1/2 4 5 1/2

T-bone, Club Rib 1 1/2 (38) 2 1/2 4 5 1/2

Sirloin 2 (51) 3 1/2 5 1/2 6 1/2

Strip Sirloin 3/4 (19) 2 1/2 3 1/2 5

Ground Steak 1/2 (13) 1 1/2 2 2 1/2

Lamb

Loin, Rib Chops 1 (25) 3 1/2 4 1/2 -

Double Rib 2 (51) 4 6 -

Fish (Low burner setting,

low rack position)

*Fish - - - 5

Fish Steak 1/2 (13) - - 4

Fish Steak 1 (25) - - 4 1/2

* It is recommended that thin  let- ounder, sole,  uke, etc., - be folded over before

cooking to increase its thickness.

Convection Ovens

Generally, a temperature 25°F to 50°F (-4°C to 10°C) lower

than that speci ed in recipes for standard ovens should

be used. Cooking time may be reduced, depending on the

product. A 2% to 5% reduction in cook time is a general

rule. Keep a close check on any product being prepared

for the  rst time. The size of the load, temperature of the

product going in and moisture content are the major factors

that in uence necessary cook times and temperatures.

Successfully prepared products should be recorded with

their times and temperatures for future reference.

Preheat the oven thoroughly before loading. It will take

approximately 15 minutes for the oven to reach 350°F

(177°C). Best results will be attained when the oven is

allowed to preheat for 30 minutes or more thorough heat

saturation.

Part # 4515576 Rev 2 (01/15/16)Page 12

Center the load on the oven racks to allow for proper heat

circulation around the sides. The oven will hold three, 18” x

26” (457mm x 660mm) sheet pans, six 12” x 20” x 2.5” (305mm

x 508mm x 64mm) steam table pans, or one 17.75”x 25.75”

(451mm x 654mm), roast pan. Never place pans directly on

the oven bottom. Always use the lowest rack position that will

allow air to circulate within the oven cavity. Load and unload

food as quickly as possible to prevent excessive temperature

drop. For even baking avoid using warped pans. Do not use

a deep pan for shallow cakes, cookies, etc., as heat circulation

across the top of these items is essential for browning. To

prevent excessive shrinkage, roast meat at a low temperature;

250°F to 325°F (121°C to 163°C).

When rethermalizing frozen products, preheat the oven 50°F

(10°C), higher than the cooking temperature to compensate

heat loss during and after loading. Return the thermostat to

the cooking temperature after loading.

To conserve energy, turn the oven o when not in use. If you

cover pans with aluminum foil, be sure to crimp it tightly

around the edges to prevent the foil from blowing o in

the oven. Any food or other or other matter that becomes

lodged in the fan must be removed as soon as the oven is

cool.

PRODUCT APPLICATION Continued

CARE & CLEANING

Stainless Steel

For routine cleaning just wash with hot water and detergent

solution. Wash just a small area at a time or the water will

evaporate leaving the chemicals behind causing streaking.

Rinse the washed area with a clean sponge dipped in a

sanitizing solution and wipe dry with soft clean cloth before

it can dry.

Use a paste (of water and a mild scouring powder) if you

have to, but never rub against the grain. All stainless steel has

been polished in one direction. Rub with the polish lines to

preserve the original  nish. Then thoroughly rinse as before.

To prevent  ngerprints there are several stainless steel

polishes on the market the leave and oily waxy  lm. Do not

use on surfaces that will be in contact with food.

Stainless steel may discolor if overheated. These stains can

usually be removed by vigorous rubbing with a scouring

powder paste.

Use only stainless steel, wood or plastic tools if necessary

to scrape o heavy deposits of grease and oil. Do not use

ordinary steel scrapers or knives, as particles of the iron may

become imbedded and rust. STEEL WOOL SHOULD NEVER BE

USED.

Oven Interior (Porcelain Enamel)

NOTE: Disconnect line cord (if applicable) from power

supply before cleaning or servicing.

1. Before cleaning oven interior, remove all oven racks and

guides. Oven racks and guides can be cleaned with a mild

soap and warm water or run through a dishwasher.

2. The porcelain interior can be cleaned with oven cleaners

such as “Easy-O ” or “Dow Oven Cleaner”. Follow product

manufacturer’s instructions for proper use.

Broiler Section

General Cleaning

Remove, empty and wash the broiler grease drawer or

container at least once a day.

On a single broiler unit the grease drawer is located inside

the valve panel. On a double broiler the grease from the

upper broiler section drains into a container suspended

from the front of the unit. The grease from the lower broiler

section drains through the hopper into a grease drawer

located inside the valve panel.

Part # 4515576 Rev 2 (01/15/16) Page 13

Remove and clean the grid rack inserts and grease drip chute

daily. Pull the grid rack forward and lift the grease rack insert

out of the frame. Remove the grease drip chute by pulling it

forward out of the rack frame guides.

MXM

The M110XM  lter should be removed and cleaned every

one to two days, depending on usage. The  lter can be

cleaned by hand with dish detergent or run though the

dishwasher.

MX (R/RC/S/TM)

The M100 series of broilers have an air fan assisted motor

with a stainless steel  lter screen to ensure a clean source of

primary air for your broiler burner combustion system. The

 lter screen is located internally in the unit behind the broiler

grease tray assembly. It is recommended that you have your

service technician remove, clean and inspect this  lter screen

when you do you regular equipment maintenance.

Grease Filter Removal on the M100X’s

1. It is recommended that this procedure be done when the

range is cool and not in use.

2. Remove all the control knobs.

3. Remove the grease tray.

4. Remove the screws for the valve panel and then remove

this panel.

5. Reach inside to access the grease  lter screen. (Located

behind the grease tray area.) The protective cover over the

 lter screen will snap o by carefully pulling downward by

hand.

6. Rinse the  lter cover and  lter with warm water and base

dish detergent soap.

7. Dry the  lter screen and cover, then carefully snap back in

place.

8. Return the valve control panel with screws.

9. Ensure the grease tray has been replaced back into

position.

10. Carefully place the control knobs back into position.

CARE & CLEANING Continued

Instructions For Removal Of Grid Rack &

Grid Rack Frame

Remove the broiler grid racks as follows:

1. Bring the grid rack down to the lowest adjustment

position.

2. Pull the entire grid rack out of the broiler as far as

possible.

3. Remove grid rack grease drip chute (located below wire

rack) by grasping hold of the chute and pulling forward

out of the frame guides.

4. Remove wire racks by lifting the front of each wire rack

over the rack front plate.

5. Pull the empty grid rack frame assembly as far forward

as possible (until the stops hit the front of the carriage

assembly), lift up on the handle and pull the rack

frame forward so the stops clear the carriage assembly.

Continue pulling the rack frame forward until the rear

bearings reach the notches in the carriage tracks and lift

the rear of the rack up and out of the carriage; the entire

frame is now free from the unit.

6. Place the rack raising lever in the highest position for

safety purposes.

Before cleaning the hopper, replace the grease drawer

to receive any drippings and solid particles freed by the

cleaning. The additional internal grease diverter should be

removed from the top section and cleaned at this time. The

diverter is removed by raising the rack assembly and lifting

up the front of the diverter. After disengaging the screws at

the front of the unit, pull the diverter forward and remove

from the unit.

Carriage mechanisms should be kept clean, particularly

around the roller bearings. If the roller bearings have been

washed clean or appear to be dry, they should be lubricated

using salt-free vegetable oil or a non-toxic high temperature

bearing lubricant.

Infra-Red Burners must be cleaned periodically by a service

professional.

Part # 4515576 Rev 2 (01/15/16)Page 14

WIRING DIAGRAM

Part # 4515576 Rev 2 (01/15/16) Page 15

Notes

GARLAND

1177 KAMATO ROAD, MISSISSAUGA, ONTARIO, CANADA, L4W1X4

8884427526

WWW.GARLANDGROUP.COM

To learn how Manitowoc Foodservice and its leading brands can equip you, visit our global web site at

www.manitowocfoodservice.com, then discover the regional or local resources available to you.

Every new piece of Manitowoc Foodservice equipment comes with KitchenCare™ and you choose the level of service that meets

your operational needs from one restaurant to multiple locations.

StarCare – Warranty & lifetime service, certi ed OEM parts, global parts inventory, performance audited

ExtraCare — CareCode, 24/7 Support, online/mobile product information

LifeCare – Install & equipment orientation, planned maintenance, KitchenConnect™, MenuConnect

Talk with KitchenCare™ • 1-844-724-CARE • www.mtwkitchencare.com

GARLAND

1177 KAMATO ROAD, MISSISSAUGA, ONTARIO, CANADA, L4W1X4

8884427526

WWW.GARLANDGROUP.COM

To learn how Manitowoc Foodservice and its leading brands can equip you, visit our global web site at

www.manitowocfoodservice.com, then discover the regional or local resources available to you.

Every new piece of Manitowoc Foodservice equipment comes with KitchenCare™ and you choose the level of service that meets

your operational needs from one restaurant to multiple locations.

StarCare – Warranty & lifetime service, certi ed OEM parts, global parts inventory, performance audited

ExtraCare — CareCode, 24/7 Support, online/mobile product information

LifeCare – Install & equipment orientation, planned maintenance, KitchenConnect™, MenuConnect

Talk with KitchenCare™ • 1-844-724-CARE • www.mtwkitchencare.com

Part # 4515576 Rev 2 (01/15/16) Page 15

SCHÉMA DE CÂBLAGE

Part # 4515576 Rev 2 (01/15/16)Page 14

5. Tirer l’ensemble du cadre vide aussi loin que possible

(jusqu’à ce que les butées touchent l’avant de l’ensemble

du chariot), soulever la poignée et tirer le cadre de

crémaillère vers l’avant de manière à ce que les butées

puissent se dégager de l’ensemble du chariot. Continuer

de tirer le cadre vers l’avant jusqu’à ce que les roulements

arrière atteignent les encoches des rails du chariot et

soulever l’arrière de la crémaillère et le sortir du chariot.

Tout le cadre est maintenant séparé de l’appareil.

6. Placer le levier de levage de crémaillère dans la position la

plus haute pour des raisons de sécurité.

ENTRETIEN ET NETTOYAGE Suite

Avant de nettoyer la trémie, remettre en place le tiroir à

graisse a n d’y recueillir toutes des particules ou gouttes

consécutives au nettoyage. Un dé ecteur à graisse interne

supplémentaire doit être retiré de la section supérieure

et être nettoyé à ce moment. Le dé ecteur est retiré en

soulevant l’ensemble de crémaillère et en soulevant la partie

avant du dé ecteur. Après avoir dégagé les vis à l’avant

de l’appareil, tirer le dé ecteur vers l’avant et le retirer de

l’appareil.

Les mécanismes du chariot doivent être maintenus propres,

surtout autour des roulements à rouleaux. Si les roulements

à rouleaux ont été lavés ou semblent être secs, ils doivent

être lubri és avec de l’huile végétale sans sel ou un lubri ant

pour roulements non toxique et résistant aux températures

élevées.

Les brûleurs à infrarouge doivent être nettoyés

périodiquement par un professionnel de service

Part # 4515576 Rev 2 (01/15/16) Page 13

L’acier inoxydable peut se décolorer s’il est trop chau é. Ces

taches peuvent être éliminées en frottant vigoureusement

avec de la crème à base de poudre à récurer.

Utiliser uniquement des outils en acier inoxydable, en

bois ou en plastique pour gratter si nécessaire les résidus

tenaces de graisses ou d’huiles. Ne pas utiliser de grattoirs

ni de couteaux en acier ordinaire, car des particules de fer

risquent de s’incruster dans les surfaces et rouiller. NE JAMAIS

UTILISER DE LAINE D’ACIER.

Intérieur Du Four (Fini En Émail Vitri é)

REMARQUE : Débrancher le cordon d’alimentation

électrique (le cas échéant) de la source électrique avant de

procéder au nettoyage ou à l’entretien.

1. Avant de nettoyer l’intérieur du four, enlever les grilles

et guides du four (en cas de base “four à convection”).

Ces pièces peuvent être nettoyées avec de l’eau tiède

savonneuse ou être mises dans le lave-vaisselle.

2 Les surfaces intérieures en émail vitri é peuvent être

nettoyées avec du produit de nettoyage pour fours

comme le “Easy-O ” ou “DOW Oven Cleaner”. Suivre les

instructions du fabricant du produit pour une utilisation

correcte.

Section Rôtissoire

Nettoyage Et Entretien

Retirer, vider et laver le tiroir ou contenant à graisse de la

rôtissoire une fois par jour au moins.

Pour un appareil à rôtissoire simple, le tiroir à graisse se

trouve à l’intérieur du panneau des robinets. Sur les appareils

à deux rôtissoires, la graisse de la section haute se vide dans

un contenant suspendu à l’avant de l’appareil. La graisse de

la section basse se vide par la trémie dans le tiroir à graisse se

trouvant à l’intérieur du panneau des robinets.

Retirer et nettoyer les inserts de crémaillère de grille et la

trémie à graisse tous les jours. Tirer la crémaillère de grille

vers l’avant et soulever l’insert hors du cadre. Retirer la trémie

à graisse en la tirant vers l’avant pour la libérer des guides du

cadre de crémaillère.

MXM

Le  ltre de l’appareil M110XM doit être retiré et nettoyé tous

les jours ou tous les deux jours, en fonction de l’utilisation. Le

 ltre peut être nettoyé à la main avec du produit de lavage à

vaisselle ou bien lavé dans le lave-vaisselle.

MX (R/RC/S/TM)

L’appareil M100 comporte un ventilateur pour la combustion

assistée avec un  ltre en acier inoxydable a n d’assurer

une bonne qualité d’air au processus de combustion. Le

 ltre est situé à l’intérieur, derrière le tirroir à graisse. Il est

recommandé qu’un technicien enlève, nettoie et inspecte le

 ltre lors de l’entretien régulier de votre appareil.

Comment sortir le  ltre.

1. Il est fortement recommandé que l’appareil soit refroidit

et non ulilisé.

2. Enlever tous les boutons de commande.

3. Enlever le tirroir à graisse.

4. Enlever les vis du panneau de commande, ensuite

enlever le panneau lui-même.

5. Enfoncer la main á l’intérieur pour acceder au  ltre. (Situé

derrière la zone du tirroir á graise.) le capot protecteur du

 ltre peut se détacher sans outil en tirant vers le bas.

6. Rincer le capot protecteur et le  ltre avec de l’eau chaude

et du produit à vaisselle.

7. Sécher le  ltre et le capot, ensuite les réinstaller avec

précaution.

8. Réinstaller le panneau de commande avec les vis.

9. S’assurer que le tirroir à graisse soit bien remis à sa place.

10 Remettre tous les boutons de commandes.

Instructions De Démontage De La Crémaillère Et

Du Cadre De Crémaillère De Grille

Retirer les crémaillères de grille de la rôtissoire comme suit :

1. Mettre la crémaillère de grille à la position la plus basse

possible de réglage.

2. Tirer l’ensemble de crémaillère de grille hors de la

rôtissoire aussi loin que possible.

3. Retirer la trémie à graisse de la crémaillère de grille (se

trouvant sous la grille) en saisissant la trémie et en la

tirant vers l’avant hors des guides du cadre.

4. Retirer les crémaillères de grilles en soulevant l’avant de la

chaque grille par-dessus la plaque avant de la crémaillère.

ENTRETIEN ET NETTOYAGE Suite

La page charge ...

Garland MST54 Owner Instruction Manual

Marque: Garland

Modèle: MST54

Catégorie: Cuisinières

Taper: Owner Instruction Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Garland MST54

Garland MST54 Owner Instruction Manual

Garland MST54 Owner Instruction Manual

dans d''autres langues

Documents connexes

Autres documents