Friedrich MR24Y3J Le manuel du propriétaire

Installation Manual

TYPE : WALL MOUNTED

Applied Models :

M24YJ

M30YJ

M36YJ

ENGLISH

FRANÇAIS ESPAÑOL

960-911-02

2

ENGLISH

• Do not cool excessively indoors. This may be harmful for your health and may consume more

electricity.

• Block sunlight with blinds or curtains while you are operating the air conditioner.

• Keep doors or windows closed tightly while you are operating the air conditioner.

• Adjust the direction of the air flow vertically or horizontally to circulate indoor air.

• Speed up the fan to cool or warm indoor air quickly, in a short period of time.

• Open windows regularly for ventilation as the indoor air quality may deteriorate if the air

conditioner is used for many hours.

• Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the

air flow or weaken the cooling / dehumidifying functions.

For your records

Staple your receipt to this page in case you need it to prove the date of purchase or for warranty

purposes. Write the model number and the serial number here:

Model number :

Serial number :

You can find them on a label on the side of each unit.

Dealer’s name :

Date of purchase :

Here are some tips that will help you minimize the power consumption when you use the air

conditioner. You can use your air conditioner more efficiently by referring to the instructions

below:

TIPS FOR SAVING ENERGY

3

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

Always comply with the following precautions to avoid dangerous situations and ensure peak

performance of your product.

WARNING

It can result in serious injury or death when the directions are ignored.

CAUTION

It can result in minor injury or product damage when the directions are ignored.

WARNING

• Installation or repairs made by unqualified persons can result in hazards to you and others.

• Air conditioner Shall be installed in accordance with national wiring regulations.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similary qualified persons in order to avoid a hazard.

• The information contained in the manual is intended for use by a qualified service technician familiar

with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment malfunction,

property damage, personal injury and/or death.

Installation

• Always perform grounding.

- Otherwise, it may cause electrical shock.

• Don’t use a power cord, a plug or a loose socket which is damaged.

- Otherwise, it may cause a fire or electrical shock.

• For installation of the product, always contact the service center or a professional installation agency.

- Otherwise, it may cause a fire, electrical shock, explosion or injury.

• Securely attach the electrical part cover to the indoor unit and the service panel to the outdoor unit.

- If the electrical part cover of the indoor unit and the service panel of the outdoor unit are not

attached securely, it could result in a fire or electric shock due to dust, water, etc.

• Always install an air leakage breaker and a dedicated switching board.

- No installation may cause a fire and electrical shock.

• Do not keep or use flammable gases or combustibles near the air conditioner.

- Otherwise, it may cause a fire or the failure of product.

• Ensure that an installation frame of the outdoor unit is not damaged due to use for a long time.

- It may cause injury or an accident.

• Do not disassemble or repair the product randomly.

- It will cause a fire or electrical shock.

• Do not install the product at a place that ther is concern of falling down.

- Otherwise, it may result in personal injury.

• Use caution when unpacking and installing.

- Sharp edges may cause injury.

• Thickness of copper pipes used are as shown “Flaring work” Table.

- Never use copper pipes thinner than that in the table even when it is available on the market

• Do not use copper pipes having a collapsed.

!

4

ENGLISH

- Otherwise, the expansion valve or capillary tube may become blocked with contaminants.

• For R410A model, use piping, flare nut and tools which is specified for R410A refrigerant.

- Using of (R22) piping, flare nut and tools may cause abnormally high pressure in the refrigerant

cycle (piping), and possibly result in explosion and injury.

• It is desirable that the amount of residual oil less than 40 mg/10m.

Operation

• Do not share the outlet with other appliances.

- It will cause an electric shock or a fire due to heat generation.

• Do not use the damaged power cord.

- Otherwise, it may cause a fire or electrical shock.

• Do not modify or extend the power cord randomly.

- Otherwise, it may cause a fire or electrical shock.

• Take care so that the power cord may not be pulled during operation.

- Otherwise, it may cause a fire or electrical shock.

• Unplug the unit if strange sounds, smell, or smoke comes from it.

- Otherwise, it may cause electrical shock or a fire.

• Keep the flames away.

- Otherwise, it may cause a fire.

• Take the power plug out if necessary, holding the head of the plug and do not touch it with wet hands.

- Otherwise, it may cause a fire or electrical shock.

• Do not use the power cord near the heating tools.

- Otherwise, it may cause a fire and electrical shock.

• Do not open the suction inlet of the indoor/outdoor unit during operation.

- Otherwise, it may electrical shock and failure.

• Do not allow water to run into electrical parts.

- Otherwise, it may cause the failure of machine or electrical shock.

• Hold the plug by the head when taking it out.

- It may cause electric shock and damage.

• Never touch the metal parts of the unit when removing the filter.

- They are sharp and may cause injury.

• Do not step on the indoor/outdoor unit and do not put anything on it.

- It may cause an injury through dropping of the unit or falling down.

• Do not place a heavy object on the power cord.

- Otherwise, it may cause a fire or electrical shock.

• When the product is submerged into water, always contact the service center.

- Otherwise, it may cause a fire or electrical shock.

• Take care so that children may not step on the outdoor unit.

- Otherwise, children may be seriously injured due to falling down.

5

ENGLISH

CAUTION

Installation

• Install the drain hose to ensure that drain can be securely done.

- Otherwise, it may cause water leakage.

• Install the product so that the noise or hot wind from the outdoor unit may not cause any damage to

the neighbors.

- Otherwise, it may cause dispute with the neighbors.

• Always inspect gas leakage after the installation and repair of product.

- Otherwise, it may cause the failure of product.

• Keep level parallel in installing the product.

- Otherwise, it may cause vibration or water leakage.

Operation

• Avoid excessive cooling and perform ventilation sometimes.

- Otherwise, it may do harm to your health.

• Use a soft cloth to clean. Do not use wax, thinner, or a strong detergent.

- The appearance of the air conditioner may deteriorate, change color, or develop surface flaws.

• Do not use an appliance for special purposes such as preserving animals vegetables, precision ma-

chine, or art articles.

- Otherwise, it may damage your properties.

• Do not place obstacles around the flow inlet or outlet.

- Otherwise, it may cause the failure of appliance or an accident.

!

6

ENGLISH

TABLE OF CONTENTS

2TIPS FOR SAVING ENERGY

3 IMPORTANT SAFETY INSTRUCTIONS

7 INSTALLATION PARTS

7 INSTALLATION TOOLS

8 INSTALLATION MAP

9 INSTALLATION

9 Select the best Location

10 Fixing Installation Plate

10 Drill a Hole in the Wall

10 Flaring Work

11 Connecting the Piping

15 Connecting the Cables

18 Checking the Drainage

19 Forming of the Piping

19 Air Purging

23 Test Running

24 Installation guide at the seaside

25 Piping Length and Elevation

25 Operation ranges

7

ENGLISH

INSTALLATION TOOLS

Name

Quantity Shape

Installation plate

1 EA

Type "A" screw

Type "B" screw

8 EA

2 EA

Remote control

holder

1 EA

The feature can be changed according a type of model.

Screws for fixing panels are attached to decoration panel.

Figure FigureName

Screw driver

Electric drill

Measuring tape, Knife

Hole core drill

Spanner

Torque wrench

Multi-meter

Hexagonal wrench

Ammeter

Gas-leak detector

Thermometer,

Level

Flaring tool set

Name

INSTALLATION PARTS

8

ENGLISH

INSTALLATION MAP

Vinyl tape (Wide)

• Apply after carrying out a

drainage test.

• To carry out the drainage

test, remove the air ﬁlters

and pour water into the heat

exchanger.

Saddle

Sleeve

Bushing-Sleeve

Putty(Gum Type Sealant)

Bend the pipe as closely

on the wall as possible,

but be careful that it

doesn't break.

Installation plate

Forced Operation Button

Air Discharge

Operation Indication Lamps/

Signal Receptor

Base Plate

Air Outlet

Air Inlet

Tubing Cover

Connecting cable (*)

Gas side piping

(*)

Liquid side piping

(*)

Additional drain pipe

(*)

Vinyl tape (Narrow)

(*)

Drain Hose

NOTE

!

• You should purchase the installation parts.

* The feature can be changed according to the type of model.

9

ENGLISH

Select the best Location

Indoor unit

- There should not be any heat or steam near

the unit.

- Select a place where there are no obstacles

around the unit.

- Make sure that condensation drainage can

be conveniently routed away.

- Do not install near a doorway.

- Ensure that the gap between a wall and the

left (or right) of the unit is more than 4in.

The unit should be installed as high as possi-

ble on the wall, allowing a minimum of 8in

from ceiling.

- Use a metal detector to locate studs to pre-

vent unnecessary damage to the wall.

* Recommended height 6.5ft from the floor

* The feature can be changed according to the

type of model.

Outdoor unit

- If an awning is built over the unit to prevent

direct sunlight or rain exposure, make sure

that heat radiation from the condenser is not

restricted.

- Ensure that the space around the back side

and other sides is more than 12in. The space

in front of the unit should be more than 28in.

- Do not place animals and plants in the path

of the warm air.

- Take the weight of the air conditioner into ac-

count and select a place where noise and vi-

bration are minimum.

- Select a place where the warm air and noise

from the air conditioner do not disturb neigh-

bors.

More than 8

More than 4

(Unit : In)

More than

12in

More than

12in

Sunroof

Fence or

obstacles

More than

28in

More than

24in

(Unit : in)

NOTE

!

Remove obstructions to prevent blockage

of airflow path.

INSTALLATION

10

ENGLISH

Fixing Installation Plate

The wall you select should be strong and solid

enough to prevent vibration

1 Mount the installation plate on the wall with

type "A" screws.

- Mount the installation plate horizontally by

aligning the centerline using Horizontal

meter .

2 Measure the wall and mark the centerline.

It is also important to use caution

concerning the location of the installation

plate. Routing of the wiring to power outlets

is through the walls typically. Drilling the

hole through the wall for piping

connections must be done safely.

Drill a Hole in the Wall

- Drill the piping hole with a ø65mm hole core

drill. Drill the piping hole at either the right or

the left with the hole slightly slanted to the

outdoor side.

Flaring Work

Main cause for gas leakage is due to defect of

flaring work. Carry out correct flaring work in

the following procedure.

1 Use the piping kit accessory or the pipes

purchased locally.

2 Measure the distance between the indoor

and the outdoor unit.

3 Cut the pipes a little longer than measured

distance.

4 Cut the cable 1.5m (4.9 ft) longer than the

pipe length.

CAUTION

Use the sleeve to prevent damage for

tube assembly.

!

Installation Plate

Chassis

Hook

Type "A" Screws

Installation plate

Left rear piping Right rear piping

43

Ø65 Ø65

43

110

120

5-7mm

(3/16"~5/16")

Indoor

WALL

Outdoor

Bushing

Sleeve

Copper

pipe

90°

Slanted Uneven Rough

Cut the pipes and the cable

11

ENGLISH

Bar

Copper pipe

Clamp handle

Red arrow mark

Cone

Yoke

Handle

Bar

"A"

Inclined

Inside is shiny without scratches

Smooth all round

Even length

all round

Surface

damaged

Cracked Uneven

thickness

= Improper ﬂaring =

Pipe

Reamer

Point down

Flare nut

Copper tube

Outside diameter A Thickness

mm inch mm mm

Ø6.35 1/4" 1.1~1.3 0.7

Ø9.52 3/8" 1.5~1.7 0.8

Ø12.7 1/2" 1.6~1.8 0.8

Ø15.88 5/8" 1.6~1.8 1.0

1. Completely remove all burrs from the cut

cross section of pipe/tube.

2. While removing burrs put the end of the

copper tube/pipe in a downward direction

while removing burrs location is also

changed in order to avoid dropping burrs

into the tubing.

- Remove flare nuts attached to indoor and

outdoor units, then put them on the pipe/tube

which have completed its burr removal.

(not possible to put them on after finishing

flare work)

Flaring work

1 Firmly hold copper pipe in a bar with the di-

mension shown in table below.

2 Carry out flaring work with the flaring tool.

1 Compare the flared work with the figures

given below.

2 If a flared section is defective, cut it off and

do flaring work again.

Connecting the Piping

1 Pull the screw cap at the bottom of the

indoor unit

2 Remove the chassis cover from the unit by

loosing 5 screws (Be careful not to scratch

Horizontal Vane Main!)

Burrs removal

Putting nut on

Check

Chassis cover

12

ENGLISH

3 Pull back the tubing holder.

4 Remove pipe port cover and positioning

the tubing

* The feature can be changed according to

type of model.

Good case

- Press on the tubing cover and unfold the

tubing to downward slowly. And then bend to

the left side slowly.

Bad case

- Following bending case from right to left di-

rectly may cause damage to the tubing.

* The feature can be changed according to

type of model.

1 Hook the indoor unit onto the upper portion

of the installation plate.( engage the three

hooks at the top of the indoor unit with the

upper edge of the installation plate) Ensure

that the hooks are properly seated on the

installation plate by moving it left and right

Installation of Indoor Unit

CAUTION

Installation Information. For right piping.

Follow the instruction above.

!

Right

Back side view

Tubing holder

Backwards

Left

Pipe Port

1

2

Installation plate

13

ENGLISH

2

Unlock the tubing holder from the chassis

and mount between the chassis and instal-

lation plate in order to separate the bottom

side of the indoor unit from the wall.

* The feature can be changed according to the

type of model.

1

Raise the cover of terminal block.

2

Insert the connecting cable through the

bottom side of indoor unit and connect the

cable. (You can see detail contents in

‘Connecting the cables’ section.)

Tubing Holder

Control Cover

1(L1)

2(L2)

3

1(L) 2(N)

3

Power connecting cable

Piping

Connecting pipe

Connecting

cable

Ta pe

Drain hose

3 Tape the tubing pipe, drain hose and the

connection cable. Be sure that the drain

hose is located at the lowest side of the

bundle. Locating at the upper side can

cause overflow from the drain pan through

the inside of the unit.

* The feature can be changed according to

the type of model.

Connecting pipe

Connecting

cable

Tape

Drain hose

CAUTION

If the extension drain hose is routed inside

the room, insulate the hose with an insula-

tion material* so that dripping from sweat-

ing (condensation) could not damage fur-

niture or floors.

• Foamed polyethylene or equivalent is

recommended.

!

NOTE

!

Insert the drain hose at left side when you

use left side piping type.

14

ENGLISH

1 Align the center of the pipes and sufficiently

tighten the flare nut by hand

2 Tighten the flare nut with a wrench

3. When needed to extend the drain hose of

indoor unit, assembly the drain pipe as

shown on the drawing.

Indoor unit tubing Flare nut Pipes

Wrench

Indoor unit tubing

Open-end wrench

(ﬁxed)

Connection

pipe

Flare nut

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit drain hose

Outside Diameter Torque

mm inch kgf·cm N·m

Ø6.35 1/4 180~250 17.6~24.5

Ø9.52 3/8 340~420 33.3~41.2

Ø12.7 1/2 550~660 53.9~64.7

Ø15.88 5/8 630~820 61.7~80.4

Connecting the installation pipe

and drain hose to the indoor unit.

Wrap the insulation material

around the connecting portion.

1 Overlap the connection pipe insulation ma-

terial and the indoor unit pipe insulation

material. Bind them together with vinyl tape

so that there may be no gap.

2 Set the tubing cutting line upward. Wrap

the area which accommodates the rear

piping housing section with vinyl tape.

3 Bundle the piping and drain hose together

by wrapping them with vinyl tape sufficient

enough to cover where they fit into the rear

piping housing section.

Vinyl tape(narrow)

Connection pipe

Connecting cable

Vinyl tape (wide)

Wrap with vinyl tape

Indoor unit pipe

Pipe

Gas Pipe

Liquid Pipe

Cutting Line

Good Case Bad Case

Wrap with vinyl tape

Drain hose

Pipe

Vinyl tape(wide)

Insulation material

* Tubing cutting line have to be upward.

Indoor Outdoor

Indoor Unit

Drain hose

Indoor Unit

Drain hose

Insulation

(More than 100~300mm

length and 7mm thickness)

Extension

drain hose

15

ENGLISH

Connecting the Cables

Connect the cable to the indoor unit by con-

necting the wires to the terminals on the con-

trol board individually according to the outdoor

unit connection. (Ensure that the color of the

wires of the outdoor unit and the terminal No.

are the same as those of the indoor unit.)

CAUTION

- The circuit diagram is a subject to

change without notice.

- The earth wire should be longer than the

common wires.

- When installing, refer to the circuit dia-

gram on the chassis cover.

- Connect the wires firmly so that they

may not be pulled out easily.

- Connect the wires according to color

codes, referring to the wiring diagram.

!

- Finally, tighten the flare nut with torque

wrench until the wrench clicks.

When tightening the flare nut with torque

wrench, ensure the direction for tightening

follows the arrow on the wrench.

Outdoor unit

Torque wrench

Liquid side piping

(Smaller diameter)

Gas side piping

(Bigger diameter)

Outside Diameter Torque

mm inch kgf·cm N·m

Ø6.35 1/4 180~250 17.6~24.5

Ø9.52 3/8 340~420 33.3~41.2

Ø12.7 1/2 550~660 53.9~64.7

Ø15.88 5/8 630~820 61.7~80.4

Connecting the Piping

- Remove the tubing cover from the unit by

loosening the screw.

- Align the center of the pipings and sufficiently

tighten the flare nut by hand.

Tubing

Cover

control

Terminal Block

Outdoor unit

16

ENGLISH

CAUTION

The power cord connected to the outdoor

unit should be complied with the following

specifications (UL recognized or CSA cer-

tified).

!

CAUTION

- Assemble it with conduit.

!

10±3mm

20mm

GN/YL

AWG_“A”

Power

Capacity(Btu/h)

24k,30k,36k

"A" 12

Power supply cable

10±3mm

20mm

GN/YL

AWG_“B”

The power connecting cable connected to the

indoor and outdoor unit should be complied

with the following specifications (UL recog-

nized or CSA certified).

Connecting

Cable

Capacity(Btu/h)

24k,30k,36k

"B" 18

Connecting cable

Indoor unit

1 Insert the connecting cable through the

bottom side of indoor unit and connect the

cable (You can see detail contents in 'Con-

necting the cables' section)

2 Secure the cable onto the control board

with the cable retainer.

3 Tape the tubing pipe, drain hose and the

connection cable. Be sure that the drain

hose is located at the lowest side of the

bundle. Locating at the upper side can

cause overflow from the drain pan through

the inside of the unit.

Control Cover

1(L1)

2(L2)

3

1(L) 2(N)

3

Power connecting cable

17

ENGLISH

CAUTION

According to the confirmation of the above con-

ditions, prepare the wiring as follows.

1 Never fail to have an individual power circuit

specifically for the air conditioner. As for the

method of wiring, be guided by the circuit

diagram posted on the inside of control

cover.

2 The screw which fasten the wiring in the

casing of electrical fittings are liable to be-

come loose from vibrations to which the unit

is subjected during the transportation.

Check them and make sure that They all

are tightly fastened. (If they are loose, it

could cause burn-out of the wires.)

3 Specification of power source.

4 Confirm that electrical capacity is sufficient.

5 See that the starting voltage is maintained

at more than 90 percent of the rated voltage

marked on the name plate.

6 Confirm that the cable thickness is as speci-

fied in the power source specification.

(Particularly note the relation between cable

length and thickness.

7 Always install an earth leakage circuit

breaker in a wet or moist area.

8 The following would be caused by voltage

drop.

- Vibration of a magnetic switch, which will

damage the contact point, fuse breaking,

disturbance of the normal function of the

overload.

9 The means for disconnection from a power

supply shall be incorporated in the fixed

wiring and have an air gap contact separa-

tion of at least 3mm in each active(phase)

conductors.

!

CAUTION

Provide the circuit breaker between power

source and the unit as shown by

!

Outdoor unit

- Connect the wires to the terminals on the

control board individually.

- Secure the cable onto the control board with

the cord clamp.

- Use a recognized circuit breaker between

the power source and the unit.

A disconnecting device to adequately discon-

nect all supply lines must be fitted.

*The feature can be changed according a type

of model.

Circuit Breaker(A)

Capacity(Btu/h)

24k,30k,36k

25

Air

Conditioner

Main power source

Circuit Breaker

Use a circuit breake

or time delay fuse.

Outdoor unit

Terminal block

Over 5mm

(0.2")

Cover control

Conduit panel

Connecting

cable

Power supply

cord

1(L1) 2(L2) 1(L1) 2(L2)

3

18

ENGLISH

* The feature can be changed according to the

type of model.

Checking the Drainage

1 Pour a glass of water on the evaporator.

2 Ensure the water flows through the drain

hose of the indoor unit without any leakage

and goes out the drain exit.

To check the drainage.

Drain pan

Connecting area

drain hose

Leakage

checking

Drain hose

Leakage

checking

2 Do not set the drain hose like the

following.

*The feature can be changed according a type

of model.

1 The drain hose should point downward for

easy drain flow.

Do not raise

Water

leakage

Accumulated

drain water

Air

Waving

Water

leakage

Tip of drain hose

dipped in water

Water

leakage

Ditch

Less than

50mm gap

Drain piping

Downward slope

19

ENGLISH

In cases where the outdoor unit is installed

above the Indoor unit perform the following.

1 Tape the piping and connecting cable from

down to up.

2 Secure the taped piping along the exterior

wall. Form a trap to prevent water entering

the room.

3 Fix the piping onto the wall using saddle or

equivalent

Air Purging

The air and moisture remaining in the refriger-

ant system have undesirable effects as indi-

cated below.

- Pressure in the system rises.

- Operating current rises.

- Cooling(or heating) efficiency drops.

- Moisture in the refrigerant circuit may freeze

and block capillary tubing.

- Water may lead to corrosion of parts in the

refrigeration system.

Therefore, after evacuating the system, take a

leak test for the piping and tubing between the

indoor and outdoor unit.

Seal a small opening

around the pipings

with gum type sealant.

Trap

Taping

Saddle

Drain hose

Pipings

Connecting cable

Seal small openings

around pipings with a

gum type sealant.

Trap is required to prevent water

from entering into electrical parts.

Drain hose

Vinyl tape(narrow)

Pipe

Wrap with

vinyl tape(wide)

Forming of the Piping

Form the piping by wrapping the connecting

portion of the indoor unit with insulation mate-

rial and secure it with two kinds of vinyl tapes.

- If you want to connect an additional drain

hose, the end of the drain outlet should be

routed above the ground. Secure the drain

hose appropriately.

In cases, where the outdoor unit is installed

below the Indoor unit, perform the following.

1 Tape the piping, drain hose and connecting

cable from down to up.

2 Secure the tapped piping along the exterior

wall using saddle or equivalent.

In cases, where the outdoor unit is installed

above the Indoor unit, perform the following.

20

ENGLISH

- Preparation

Check that each tube(both liquid and gas

side tubes) between the indoor and outdoor

units have been properly connected and all

wiring for the test run has been completed.

Remove the service valve caps from both the

gas and the liquid side on the outdoor unit.

Note that both the liquid and the gas side

service valves on the outdoor unit are kept

closed at this stage.

- Leak test

Connect the manifold valve(with pressure

gauges) and dry nitrogen gas cylinder to this

service port with charge hoses.

Air purging with vacuum pump

CAUTION

Be sure to use a manifold valve for air

purging. If it is not available, use a stop

valve for this purpose. The knob of the

3-way valve must always be kept close.

- Pressurize the system to maximum

250 P.S.I.G. (17.6 kgf/cm

2

G) (R-22

model) or 400 P.S.I.G. (28.1 kgf/cm

2

G)

(R-410A model) with dry nitrogen gas

and close the cylinder valve when the

gauge reading reaches 250 P.S.I.G.

(17.6 kgf/cm

2

G) (R-22 model) or 400

P.S.I.G. (28.1 kgf/cm

2

G) (R-410A model).

Next step is leak test with liquid soap.

!

CAUTION

To avoid nitrogen entering the refrigerant

system in a liquid state, the top of the

cylinder must be higher than its bottom

when you pressurize the system. Usually,

the cylinder is used in a vertical standing

position.

!

WARNING

!

There is a risk of fire and explosion.

Inert gas (nitrogen) should be used

when you check plumbing leaks, cleaning

or repairs of pipes etc.

If you are using combustible gases includ-

ing oxygen, product may have the risk of

fires and explosions.

- Do a leak test of all joints of the tubing(both

indoor and outdoor) and both gas and liquid

side service valves.

Bubbles indicate a leak. Be sure to wipe off

the soap with a clean cloth.

- After the system is found to be free of leaks,

relieve the nitrogen pressure by loosening

the charge hose connector at the nitrogen

cylinder. When the system pressure is re-

duced to normal, disconnect the hose from

the cylinder.

*The feature can be changed according a type

of model.

- Remove the caps from the 2-way and 3-way

valves.

- Remove the service-port cap from the 3-way

valve.

- Apply a soap water or a liquid neutral deter-

gent on the indoor unit connection or outdoor

unit connections by a soft brush to check for

leakage of the connecting points of the pip-

ing.

- If bubbles come out, the pipes have leakage

Lo Hi

Outdoor unit

Manifold valve

Charge hose

Nitrogen gas

cylinder(in vertical

standing position)

Pressure

gauge

Indoor unit

Soap water method

La page charge ...

Friedrich MR24Y3J Le manuel du propriétaire

Friedrich MR24Y3J Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents