Scotts 60062S Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire
OWNERS MANUAL
21 in. - 62 VOLT LITHIUM-ION CORDLESS MOWER
5.0Ah Lithium-ion Battery
Copyright All Rights Reserved.
Model 60062S
Your lawn mower has been engineered and manufactured to our high standard for dependability, ease of operation,
and operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the owners manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
CA Compliant
Charger Included
(Model No.
CHL86200)
DO NOT RETURN THIS PRODUCT TO THE STORE. OPERATING,
ASSEMBLY, PARTS, SERVICE QUESTIONS? GO TO
SCOTTS.AMERICANLAWNMOWER.COM OR CALL 1-800-618-7474
BETWEEN 8:00 AM—5:00 PM EST FOR ASSISTANCE.
244026
BATTERY MUST BE CHARGED
BEFORE FIRST USE. TWO TO
THREE INITIAL CHARGING/
DISCHARGING CYCLES MAY BE
REQUIRED TO ACHIEVE MAXIMUM
RUN TIME/CAPACITY.
Introduction…………………………………..…………………………………………...2
Important Safety Instructions.………………………...……………………………...3-5
Symbols……………………………………..…………………………………………... 6
Features………………………………………………………………………………. 7-8
Assembly…………………………………………………………………...………...8-11
Operation…………………………………...……………………………...……….11-14
Charging the battery pack……………………………………………………………..15
Maintenance………………………………..………………………………...…….16-18
Troubleshooting…...…...………………………………….…………………….……. 19
Parts and Service.………………………….…………………………………………..20
Notes…………………………………………………………………………………….21
Warranty………………………………………..………………………...……Back Page
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance,
and dependability have been given top priority in the design of this product making it easy to maintain
and operate.
TABLE OF CONTENTS
SAVE THESE INSTRUCTIONS
2
Model 60062S
Refer to the recommended ambient temperature range for appliance and battery use and
storage, and for charging system during charging.
WARNING:
To avoid serious injury, do not attempt to use this product until you read thoroughly and understand
completely the owners manual. If you do not understand the warnings and instructions in the owners
manual, do not use this product. Call Scotts customer service for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and, when needed, a full face shield. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
with side shields. Always use eye protection which is marked to comply with ANSI Z87.1.
Recommended Ambient Temperature Range
Mower Operation 41 °F - 104 °F (5 °C - 40 °C)
Mower Storage 32 °F - 100 °F (0 °C - 38 °C)
Battery Charging 39 °F - 104 °F (4 °C - 40 °C)
Charger Operation 39 °F - 104 °F (4 °C - 40 °C)
Battery Storage 32 °F - 104 °F (0 °C - 40 °C) for 3 months before charging is required.
Battery Discharging 32 °F - 104 °F (0 °C - 40 °C)
IMPORTANT SAFETY INSTRUCTIONS
3
Model 60062S
SAFETY INSTRUCTIONS FOR PEDESTRIAN-CONTROLLED
MOWERS
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below and on the
machine may result in electric shock, fire, and/or serious
personal injury.
IMPORTANT - Safe Practices for Pedestrian-Controlled
Mower
This machine is capable of amputating hands and feet and
throwing objects. Failure to observe the following safety
instructions could result in serious injury or death.
I. GENERAL INFORMATION
1. Read, understand, and follow instructions and warnings in
this manual and on the machine, engine and attachments.
2. Only allow operators, who are responsible, trained, familiar
with the instructions, and physically capable to operate the
machine.
3. Keep bystanders away.
4. Do not operate the machine while under the influence of
alcohol or drugs.
II. PREPARATION BEFORE OPERATING
1. Clear the operating area of any objects which could be
thrown by or interfere with operation of the machine.
2. Keep the area of operation clear of all bystanders,
particularly small children. Stop the machine and
attachment (s) if anyone enters the area.
3. Do not operate the machine without the entire grass
catcher, discharge chute, or other safety devices in place
and functioning properly. Check frequently for signs of wear
or deterioration and replace as needed.
4. Wear appropriate personal protective equipment such as
safety glasses, hearing protection, and footwear.
III. OPERATING
1. Only operate the machine in daylight or good artificial light.
2. Avoid holes, ruts, bumps, rocks, or other hidden hazards.
Uneven terrain could overturn the machine, or cause
operator to lose their balance or footing.
3. Do not put hands or feet near rotating parts or under the
machine. Keep clear of the discharge opening at all times.
4. Do not direct discharge material toward anyone. Avoid
discharging material against a wall or obstruction. Material
may ricochet back toward the operator. Stop the blade (s)
when crossing gravel surfaces.
5. Do not leave a running machine unattended. Always park
on level ground, disengage the attachment, and stop
engine.
6. Do not mow in reverse unless absolutely necessary.
Always look down and behind before and while backing.
IV. CHILDREN SPECIFIC
1. Tragic accidents can occur if the operator is not alert to the
presence of children. Children are often attracted to the
machine and the mowing activity. Never assume that
children will remain where you last saw them.
2. Keep children out of the operating area and under the
watchful care of a responsible adult other than the
operator.
V. SLOPE SPECIFIC
Slopes are a major factor related to accidents. Operation on
slopes requires extra caution.
1. Travel in the manufacturer recommended direction on
slopes. Use caution while operating near drop-offs.
2. Avoid mowing wet grass. (Poor footing could cause a slip
and fall accident.)
3. Do not operate machine under any condition where
traction, steering, or stability is in question. Tires could slide
even if the wheels are stopped.
4. Always keep the machine in gear when going down slopes.
Do not coast downhill.
5. Avoid starting and stopping on slopes. Avoid making
sudden changes in speed or direction. Make turns slowly
and gradually.
6. Use extra care while operating machine with a grass
catcher or other attachment (s). They can affect the stability
of the machine.
VI. HAULING
1. Use full width ramps for loading and unloading a machine
for transport.
VII. SERVICE
1. Keep machine in good working order. Replace worn or
damaged parts.
2. Use caution when servicing blades. Wrap the blade (s) or
wear gloves. Replace damaged blades. Do not repair or
alter blade (s).
3. Remove or disconnect battery before servicing or making
any repairs.
WARNING: California Proposition 65:
This product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive
harm.
WARNING: Some dust and debris created by the use of this
tool could contain chemicals known to the State of California to
cause cancer and birth defects or other reproductive harm.
Some examples of these chemicals are:
Chemicals in fertilizers
Compounds in insecticides, herbicides and pesticides
Arsenic and chromium from chemically treated lumber
Your risk from exposure to these chemicals varies, depending
on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved
safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
WARNING: Cancer and Reproductive Harm –
www.P65Warnings.ca.gov.
IMPORTANT SAFETY INSTRUCTIONS
4
Model 60062S
Avoid Dangerous Environment - Do not use the lawn mower in
damp or wet conditions or operate in the rain.
Keep the area clear of all bystanders, children, and pets while
mowing. Stop machine if anyone enters the area.
Dress properly - Do not wear loose clothing or jewelry. They
can be caught in moving parts. Use of rubber gloves and
footwear is recommended when working outdoors.
Dont over reach - Keep firm footing and balance. Do not
overreach. Over-reaching can result in loss of balance.
Do not operate the equipment with barefoot or when wearing
sandals or similar lightweight footwear. Wear protective
footwear that will protect your feet and improve your footing on
slippery surfaces.
Use safety glasses - Always wear safety glasses with side
shields. Everyday glasses have only impact resistant lenses.
They are NOT safety glasses. Following this rule will reduce
the risk of eye injury. Use face mask if environment is dusty.
Wear safety glasses or goggles that are marked to comply with
ANSI Z87.1 standard when operating this product.
Use the right appliance - Do not use the lawn mower for any
job except that for which it is intended.
Do not force the lawn mower - It will do the job better and safer
at the rate for which it was designed.
Stay alert - Watch what you are doing, and use common sense
when operating the lawn mower. Do not operate the mower
while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating the lawn
mower may result in serious personal injury.
Maintain lawn mower with care - Keep machine in good
working condition. Keep blades sharp and guards in place and
in working order.
Check all nuts, bolts, and screws at frequent intervals for
proper tightness to be sure the equipment is in safe working
condition.
Stop the motor, remove the switch key and wait until the blade
comes to a complete stop before cleaning the lawn mower,
removing the grass catcher, unclogging the discharge opening,
or making any repairs or inspections.
When not in use, mower should be stored indoors in a dry,
locked up place—out of reach of children.
Always use safety protective devices. Do not operate the
mower without the entire grass catcher discharge guard, rear
guard, or other safety protective devices in place and working.
Follow manufacturers instructions for proper operation and
installation of accessories. Only use accessories approved by
the manufacturer.
Do not mow on wet grass or excessively steep slopes. Poor
footing could cause a slip and fall accident. Walk, never run.
Use extra care when approaching blind corners, shrubs, trees,
or other objects that may block your view.
Clear the work area before each use. Remove all objects such
as rocks, sticks, wire, bones, toys, or other objects which can
be thrown by the blade. Stay behind the handle when the
motor is running.
Do not mow near drop-offs, ditches, or embankments.
Mow across the face of slopes, never up and down. Exercise
extreme caution when changing direction on slopes.
Plan your mowing pattern to avoid discharge of material
towards roads, sidewalks, bystanders and the like. Also, avoid
discharging material against a wall or obstruction, which may
cause the material to ricochet back toward the operator.
Do not pull the mower backward unless absolutely necessary.
If you must back the mower away from a wall or obstruction
first look down and behind to avoid tripping.
Objects struck by the lawn mower blade can cause severe
injuries to persons. The lawn should always be carefully
examined and cleared of all objects prior to each mowing.
If the lawn mower strikes a foreign object, follow these steps:
Stop the lawn mower and release the switch control
bail wire,
Remove the switch key
Thoroughly inspect the mower for any damage
Repair any damage before restarting and continuing to
operate the mower.
Stop the motor, remove the switch key, and wait until the blade
comes to a complete stop before removing the grass catcher
or unclogging the chute, The cutting blade continues to rotate
for a few seconds after the motor is shut off. Never place any
part of the body in the blade area until you are sure the blade
has stopped rotating,
If the mower should start to vibrate abnormally, stop the motor
and check immediately for the cause. Vibration is generally a
warning of trouble.
Service on the product must be performed by qualified repair
personnel only. Service or maintenance performed by
unqualified personnel could result in injury to the user or
damage to the product.
Use only identical replacement parts when servicing the
product. Use of unauthorized parts may create a risk of
serious injury to the user or damage to the product.
Replace blade if it is bent or cracked. An unbalanced blade
causes vibration that could damage the motor drive unit or
cause personal injury. Sharpen a dull blade equally at each
end to maintain the balance. Clean the blade thoroughly and
check its balance by supporting it horizontally on a thin nail
through its center hole. The nail should be in a horizontal
position. If either end of the blade rotates downward, remove
some metal from the heavy or lower end until the blade is
balanced. It is balanced when neither end drops.
The grass bag assembly is subject to deterioration and wear
and should be checked each time the mower is used. If
replacement is needed, make sure the new grass bag meets
original manufacturers recommendations and specifications.
Maintain or replace safety instructions labels, as necessary.
Store idle lawn mower indoors - When not in use, mower
should be stored indoors in a dry, locked place out of the reach
of children. The start key should also be removed and stored in
a separate location out of the reach of children.
Follow instructions for lubricating and changing accessories.
Never operate machine in a closed area.
Never tamper with safety devices. Check for proper operation
regularly.
Never attempt to make a wheel height adjustment while the
motor is running.
Do not wash with a hose; avoid getting water in motor and
electrical connections.
IMPORTANT SAFETY INSTRUCTIONS
5
Model 60062S
SAFETY RULES FOR BATTERY AND CHARGER
Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to battery pack. Energizing
appliance that have the switch on invites accidents.
Disconnect the battery pack from the appliance before
making any adjustments, changing accessories, or storing
appliance. Such preventive safety measures reduce the risk
of starting the appliance accidentally.
Recharge only with Scotts 62V charger (CHL86200). A
charger that is suitable for one type of battery pack may
create a risk of fire when used with another battery pack.
Use appliances only with Scotts 62V lithium-ion battery
packs (BL86225, BL86240, BL86250). Use of any other
battery packs may create a risk of injury and fire. See
Charger Manual.
When battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws or
other small metal objects, that can make a connection from
one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs, flush
with water. If liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause irritation or
burns.
Do not use a battery pack or appliance that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk of
injury.
Do not expose a battery pack or appliance to fire or
excessive temperature. Exposure to fire or temperature
above 265°F (130°C) may cause explosion.
Follow all charging instructions and do not charge the
battery pack or appliance outside of the temperature range
specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage
the battery and increase the risk of fire. See Charger
Manual.
Have servicing performed by a qualified repair person using
only identical replacement parts. This will ensure that the
safety of the product is maintained.
Do not modify or attempt to repair the appliance or the
battery pack (as applicable) except as indicated in the
instructions for use and care.
Do not open or mutilate battery (ies). Released battery fluid
may cause damage to the eyes, or skin. It may be toxic if
swallowed.
Exercise care in handling batteries in order not to short the
battery with conducting materials such as rings, bracelets,
and keys. The battery or conductor may overheat and cause
burns.
Disconnect battery - Disconnect battery pack from the
appliance before storing, servicing, transporting, or changing
accessories such as blades. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Stop the unit and disconnect battery pack and start key
when not in use. Carry or push the unit with the motor
stopped and the start key and battery pack removed from
the mower.
Battery tools do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition.
Be aware of possible hazards when not using your
battery tool or when changing accessories. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not use battery-operated appliance in rain.
Remove or disconnect battery before servicing, cleaning
or removing material from the gardening appliance.
Do not charge lawn mower in rain, or in wet locations.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away from
heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons. Following this rule will
reduce the risk of electric shock, fire, or serious personal
injury.
Do not service mower with battery, switch key, or charger
installed.
Do not use the charger when the ambient temperature is
above 104°F (40°C) or below 39°F (4°C).
Do not operate charger with a damaged cord or plug
which could cause shorting and electric shock. If
damaged, replace the charger with an identical charger
from an authorized service provider.
Do not operate charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Take it
to an authorized service center for electrical check to
determine if the charger is in good working order.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when not in
use to prevent damage to the charger during a power
surge,
Risk of electric shock, Do not touch uninsulated portion of
output connector or uninsulated battery terminal.
Do not expose charger to wet or damp conditions, Water
entering charger will increase the risk of electric shock,
Make sure cord is located so that it will not be stepped on,
tripped over, come in contact with sharp edges or moving
parts or otherwise subjected to damage or stress. This will
reduce the risk of accidental falls, which could cause
injury, and damage to the cord, which could result in
electric shock.
Keep cord and charger away from heat to prevent
damage to housing or internal parts.
Do not let gasoline, oils, petroleum-based products, etc.
come in contact with plastic parts. They contain chemicals
that can damage, weaken or destroy plastic.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this product. If you
loan someone this tool, loan them these instructions also.
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better
and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
W Watt Power
hrs Hours Time
Gal Gallon Volume
qt Quart Volume
Wet Conditions Alert Do not expose to rain or use in damp locations
Read the Owners Manual To reduce the risk of injury, user must read and
understand owners manual before using this product.
Eye Protection Always wear safety goggles or safety glasses with side
shields and, as necessary, a full face shield when
operating this product.
Safety Alert Precautions that involve safety
Electric Shock Failure to use in dry conditions and to observe safe
practices can result in electric shock
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
SYMBOL SIGNAL MEANING
DANGER Indicates an imminently hazardous situation, which, if not
avoided, will result in death or serious injury.
WARNING Indicates a potentially hazardous situation, which, if not
avoided, could result in death or serious injury.
CAUTION Indicates a potentially hazardous situation, which, if not
avoided, may result in minor or moderate injury.
CAUTION (Without Safety Alert Symbol) Indicates a situation that
may result in property damage.
6
Model 60062S
FEATURES
PRODUCT SPECIFICATIONS
60062S
*Battery…………………...62V 5.0Ah Lithium-ion Battery
Input………………………………………….. 62V DC only
No-load Speed………………………………... 2650 RPM
Charge time.…………………………………..180 minutes
Height Adjustments…………………..1-1/2 in. to 3-3/4 in.
Wheel Size………………………….7 in. front, 10 in. rear
Grass Catcher Capacity…………………1.7 Bushel (60L)
Weight………………………………………..64 lbs (29 kg)
* This product contains a rechargeable lithium-ion battery. Battery must be recycled. Do not dispose of this product in
fire. Battery inside this product may explode or leak. Before disposing of damaged or worn out battery packs contact
your local waste disposal agency or the local Environmental Protection Agency for information and specific instructions.
Take the battery to a local recycling and/or disposal center for disposal. Never throw the battery pack away in a
standard receptacle or have it incinerated. See page 15 for more details.
Side Discharge Deflector
Mulching Plug
62V Charger
62V Battery
7
Model 60062S
Fig. 1
Bail Wire
LED Lights
Switch Button
Upper Handle
Handle Locking
Clamp
Handle Locking
Clamp
Quick Adjust Lever
Lower Handle
Safety Lock-out
Button
Grass Catcher
Rear Door
Height
Adjustment
Lever
Battery Cover
Rear Wheel
Front Wheel
Side Discharge
Cover
Front Handle
Power Indicator
Switch Key
LED Lights
UNPACKING
This product requires assembly.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing
list are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-800-618-7474 for assistance.
PACKING LIST
LED LIGHTS SWITCH BUTTON
Used to turn on/off the LED lights at the front of the
mower.
MULCHING PLUG
Your mower is equipped with a mulching plug that
allows the blade to cut and recut the grass for finer
clippings.
SWITCH KEY
The switch key must be inserted before the mower can
be started.
SIDE DISCHARGE DEFLECTOR
Use the side discharge deflector on your mower when
the grass is too high to mulch or when side discharging
is preferred. The grass clippings produced when using
the side discharge deflector are noticeably larger than
those produced when using the mulching plug.
KNOW YOUR LAWN MOWER
See figure 1
The safe use of this product requires an understanding of
the information on the product and in this owners
manual as well as a knowledge of the project you are
attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.
BATTERY METER/ POWER INDICATOR
The battery meter measures the amount of charge
remaining in the battery.
GRASS CATCHER
The grass catcher prevents grass clippings from being
strewn across your lawn as you mow.
HEIGHT ADJUSTMENT LEVER
The height adjustment lever provides cutting height
adjustments.
MOTOR/BLADE CONTROL ASSEMBLY
The motor/blade control, located on the upper handle of
the mower, engages and disengages the motor and blade.
WARNING:
Do not insert switch key until assembly is complete.
Failure to comply could result in accidental starting
and possible serious injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this
product. Any such alteration or modification is
misuse and could result in a hazardous condition
leading to possible serious personal injury.
WARNING:
If any parts are damaged or missing do not operate
this product until the parts are replaced. Failure to
heed this warning could result in serious personal
injury.
DANGER:
To prevent accidental starting do not make any
adjustments or installations with the switch key
inserted or batteries installed.
FEATURES
ASSEMBLY
WARNING:
Never operate the mower without the proper safety
devices in place and working. Never operate the
mower with damaged safety devices. Failure to heed
this warning can result in serious personal injury.
Description Quantity
Lawn Mower 1
Switch Key 1
Mulching Plug 1
Side Discharge Deflector 1
Grass Catcher 1
62V 5.0Ah Battery 1
62V Charger 1
Owners manual 1
8
Model 60062S
UNFOLDING AND ADJUSTING HANDLE ASSEMBLY
See figure 2-4
WARNING: Folding or unfolding the handle improperly
can damage the cables, causing an unsafe operating
condition.
Do not damage the cables when folding or
unfolding the handle.
If a cable is damaged, contact an Authorized
Service Dealer.
WARNING: Do not attempt to start the mower until the
handle has been locked at one of the two preset
operating positions.
LOCKED STORAGE POSITION: Your mower is
shipped with the handle in the compact, locked position.
Hold the handle (1) up with one hand. Press and hold
the quick-adjust lever (2) with the other hand to release
the handle from the locked storage position. Begin to lift
the handle (1) from its folded position, and then release
the lever. Gently pivot the handle upward until you hear
and feel the lock pin engage in position.
OPERATING POSITIONS
NOTE: The motor cannot be
started unless:
a. the handle is locked into
one of the operating
positions,
b. the upper handle is fully
extended.
Upper Operating Position:
Lift the handle with one hand.
Gently pivot the handle backward until you hear
and feel the lock pin engage in the upper Operating
position. Taller users may prefer this position.
ASSEMBLY
Lower Operating Position:
Hold the handle with one hand. Press and hold the
quick-adjust lever with the other hand to release the
handle from the upper operating position.
Begin to lower the handle, and then release the
lever. Gently pivot the handle downward until you
hear and feel the lock pin engage in the lower
Operating position.
Once the mower is set in one of the Operating
Positions,
Open the handle locking clamps (1).
Fully extend the upper handle (2).
Securely close the handle locking clamps (1).
9
Model 60062S
Fig. 2
Fig. 3
Fig. 4
1
2
1
1
2
Lower
Operating
Position
Upper
Operating
Position
ASSEMBLY
INSTALLING SIDE DISCHARGE CHUTE
(For Side Discharging Operation)
See figure 7
Lift the side discharge cover (1).
Align the grooves (2) on the side discharge
deflector (3) with the pins (4) on the underside of
the discharge cover (1).
Lower the discharge chute until the hooks on the
mower deck are secured in the openings in the
discharge chute.
Release the side discharge cover.
NOTE: When using side discharge, do not install the
grass catcher. Ensure the mulch plug is installed.
10
Model 60062S
INSTALLING THE GRASS CATCHER BAG
(For Rear Bagging Operation)
See figure 5
Lift the rear discharge door (1).
Lift the grass catcher by its handle (2) and place
under the rear discharge door so that the hooks (3)
on the grass catcher are seated on the door rod (4).
Release the rear discharge door. When installed
correctly, the hooks on the grass catcher will extend
through the openings on the rear discharge door.
NOTE: When using the grass catcher, do not install
either the side discharge deflector or the mulching plug.
REMOVING/INSTALLING THE MULCHING PLUG
(For Mulching Operation)
See figure 6
The mulching plug must be removed in order to install
the grass catcher.
To remove the mulching plug, lift the rear discharge
door (1).
Grasp the handle (2) of the mulching plug. Lift and
pull the mulching plug out using the handle.
The mulching plug (3) is inserted at an angle, so it
requires some force to remove it.
The mulching plug must be re-installed when the grass
catcher is removed.
To install the mulching plug, lift the rear discharge
door (1).
Grasp the handle (2) of the mulching plug. Lift and
insert the mulching plug in at an angle using the
handle.
NOTE: When mulching, do not install either the side
discharge deflector or the grass catcher.
Fig. 5
1
2
3 4
Fig. 6
2
3
1
Fig. 7
1
4
2
3
INSTALLING/REMOVING BATTERY PACK
See figure 8
To Install Battery Pack
Lift and hold up the battery cover (1).
Align the battery (2) with the mowers battery port.
Make sure the battery release button (3) snaps in
place and that battery is fully seated and secure in
the mower before beginning operation.
If the machine is not going to be used immediately,
remove the battery.
To Remove Battery Pack
Release the bail lever to stop the mower.
Press the battery release button (3) on the mower.
Open the battery cover.
Remove battery from the mower.
ASSEMBLY
This product will accept Scotts 62V lithium-ion
battery packs only.
For complete charging instructions, refer to the
Owners manuals for your battery pack and charger
models.
WARNING: Always remove battery pack from your tool
when you are assembling parts, making adjustments,
cleaning, carrying, transporting or when not in use.
Removing battery pack will prevent accidental starting
that could cause serious personal injury.
NOTE: To avoid serious personal injury, always
remove the battery pack and keep hands clear of the
trigger release button when carrying or transporting the
tool.
WARNING: Make sure the latch on the tool snaps in
place and the battery pack is fully seated and secure in
the battery port before beginning operation. Failure to
securely seat the battery pack could cause the battery
pack to fall out, resulting in serious personal injury.
SWITCH KEY
In order to prevent accidental start-up or unauthorized
use of your cordless mower, a removable switch key
has been incorporated into the design of your mower.
The mower will be completely disabled when the switch
key has been removed from the mower.
WARNING: The cord on the switch key is used for
storage; keep it out of the reach of children. DO NOT
tether the switch key to mower.
DANGER: Rotating blades can cause serious injury. To
prevent serious injury, remove the switch key when the
mower is unattended, or when adjusting, cleaning,
servicing, transporting, lifting, or storing the mower.
11
Model 60062S
Fig. 8
1
3
2
OPERATION
WARNING:
Do not allow familiarity with this type of product to make
you careless. Remember that a careless fraction of a
second is sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating this product. Failure to do so
could result in objects being thrown into your eyes,
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The
use of attachments or accessories not recommended can
result in serious personal injury.
APPLICATIONS:
You may use this product for the purpose listed below:
Mowing your lawn
12
Model 60062S
OPERATION
STARTING/STOPPING THE MOWER
See figure 9-10
To start the mower:
Raise the battery cover (1).
Install battery pack (2).
Insert the switch key (3) into the slot beside the
battery port.
Lower the battery cover (1).
Press and hold the safety lock-out button (1).
While continuing to hold the start button, pull the bail
wire (2) toward the handle (3). Once the motor
starts, release the button (1).
To stop the mower:
Release the bail wire (2).
SOFT-START
This LI-ION mower is equipped with a soft-start
feature. When initially starting up, the mower will take
approx. 3 seconds to get up to full speed. If the mower
does not initially start: Remove the battery and check
under the mower deck to ensure there is nothing
obstructing the blade and that the blade can spin freely
by hand. Even a small amount of grass on start up will
prevent the soft-startfrom turning the mower on.
CAUTION: Do not attempt to override the operation of
the safety lock-out button or bail lever.
1
2
3
Fig. 9
Fig. 10
2
1
LED LIGHTS
See figure 10-11
The LED lights (1) are located at the front of the motor
cover. The lights can only be illuminated when the
battery and switch key are installed in the mower and
when the bail wire is engaged.
To turn on, press the LED lights switch button (4). The
lights will illuminate when the bail wire (2) is pulled
toward the handle (3).
When the bail wire (2) is released, the lights will remain
lit for a few seconds before automatically going
out. When the bail wire (2) is engaged again, the lights
will illuminate.
To turn the LED lights off, press the LED switch button
(4) again.
POWER INDICATOR ON THE MOWER
See figure 10, 12
The mower is equipped with a power indicator (5) to
indicate the charge capacity status of the battery pack
and the working status of the mower. By pressing the
button, LED displays shows the battery capacity.
Fig. 11
1
LED lights Battery status
All LED are lit Full charged (75-100%)
LED 1, 2, 3 are lit Battery is 50%-75% charged
LED 1, 2 are lit Battery is 25%-50% charged
LED 1 is lit Battery is empty (0%-25%).
Charge the battery.
3
4
5
Fig. 12
OPERATION
WARNING: The operation of any mower can result in
foreign objects being thrown into the eyes, which can
cause severe eye damage. Always wear safety glasses
while operating the mower and while performing any
adjustments or repairs.
WARNING: Ensure that other people and pets remain
at least 100 feet (30 m) away when the mower is in
use.
INSPECT THE CUTTING AREA
Remove all stones, sticks, wire, bones, and other
debris that might be thrown by the rotating blades.
SETTING BLADE HEIGHT
See figure 13
When shipped, the wheels on the mower are set to a
low-cutting position. Before using the mower for the first
time, adjust the cutting position to the height best suited
for your lawn. The average lawn should be between
1-1/2 in. to 2 in. during the cool months and between 2
in. to 3 1/4 in. during the hot months.
The mower can be set to 6 cutting heights between
1.5" (38mm) and 3.75" (95mm). Choose the proper
cutting height according to the types and conditions of
the grass.
To adjust the blade height:
To raise the blade height, grasp the height
adjustment lever (1) and move it toward the back of
the mower.
To lower the blade height, grasp the height
adjustment lever (1) and move it toward the front
of the mower.
MOWING TIPS
Make sure the lawn is clear of stones, sticks, wires
and other objects that could damage the lawn
mower blades or motor. Such objects could be
accidentally thrown by the mower in any direction
and cause serious personal injury to the operator
and others.
For a healthy lawn, always cut off one-third or less
of the total length of the grass.
When cutting heavy grass, reduce walking speed
to allow for more effective cutting and a proper
discharge of the clippings.
Do not cut wet grass. It will stick to the underside
of the deck and prevent proper mulching of grass
clippings.
New or thick grass may require a narrower cut.
Clean the underside of the mower deck after each
use to remove grass clippings, leaves, dirt and any
other accumulated debris.
SLOPE OPERATION
See figure 14
WARNING: Slopes are a major factor related to slip
and fall accidents that can result in severe injury.
Operation on slopes requires extra caution. If you feel
uneasy on a slope, do not mow it. For your safety, do
not attempt to mow slopes greater than 15 degrees.
Mow across the face of slopes, not up and down.
Exercise extreme caution when changing direction
on slopes.
Watch for holes, ruts, rocks, hidden objects, or
bumps which can cause you to slip or trip. Tall
grass can hide obstacles. Remove all objects such
as rocks, tree limbs, etc., which could be tripped
over or thrown by the blade.
Always be sure of your footing. A slip and fall can
cause serious personal injury. If you feel you are
losing your balance, release the switch control bail
wire immediately.
Do not mow near drop-offs, ditches, or
embankments; you could lose your footing or
balance.
13
Model 60062S
Fig. 13
1
Fig. 14
MULCHING TIPS
NOTE: Inspect the area where the mower is to be used,
and remove all stones, sticks, wire, bones, and other
debris that might be thrown by the rotating blade.
Release the bail lever to turn the mower OFF when
crossing any graveled area (stones can be thrown
by the blade).
Set mower to the highest cutting height when
mowing on uneven ground or in tall weeds.
For effective mulching, do not cut wet grass,
because it tends to stick to the underside of the
deck, preventing proper mulching of grass
clippings. New or thick grass may require a
narrower cut. The ground speed should be adjusted
to the condition of the lawn.
Walk at a steady pace. Overlap the cutting rows. Do
not let the grass get too tall. If the grass gets too
long, start at the highest cutting position and work
down to the desired cutting height.
WARNING: If you strike a foreign object, stop the motor
and remove the battery. Thoroughly inspect the mower
for any damage. Repair any damage before operating
the mower. Excessive vibration of the mower during
operation is an indication of damage. Thoroughly
inspect the mower and repair any damage before
operating the mower.
OPERATION
EMPTYING THE GRASS CATCHER
See figure 15
Stop mower and allow blades to completely stop.
Open battery cover.
Remove switch key and battery pack.
Lift the rear discharge door.
Lift the grass catcher by its handle to remove from
mower.
Empty grass clippings.
Lift the rear discharge door and reinstall the grass
catcher as described earlier in this manual.
Reinstall switch key and battery pack when you
are ready to mow.
Fig. 15
14
Model 60062S
15
Model 60062S
CHARGING THE BATTERY PACK
Charge the battery pack only with the charger provided.
Allow at least 90 minutes of charge time for 2.5Ah battery or
140 minutes of charge time for 4Ah battery or 180 minutes of
charge time for 5Ah battery before initial use of the mower.
Make sure the power supply is normal household voltage,
120 volts, 60Hz, AC only.
The battery charger should be operated in temperatures
between 39 and 104 degrees F (4 °C and 40 °C).
The battery should be charged in a cool, dry place.
2 to 3 initial charging/discharging cycles may be required to
achieve maximum run time/capacity.
DO NOT attempt to open the charger or the unit. There are
no customer serviceable parts inside. Call customer service
helpline at 1-800-618-7474 for assistance.
DO NOT incinerate battery packs even if they are severely
damaged or completely worn out. They can explode in a fire
causing injury.
DO NOT charge appliance in rain, or in wet locations.
Use the battery charger indoors only.
Disconnect charger from the power supply when not in use to
prevent damage to the charger during a power surge.
When fully charged, the battery can be safely stored in
temperatures down to -4 degrees F (-20 degrees C) for a
period of up to four weeks, before requiring charging. Fully
charge battery pack every 90 days.
If over a period of time the battery pack quickly runs down
after a full 90, 140 or 180 minutes charging period,
a replacement battery pack is needed.
To prevent permanent damage to the battery, never store in
a discharged condition.
WINTER STORAGE - Fully recharge before storage and
then again every 90 days.
Since the battery will not develop a memory, it does not
have to be fully discharged before recharging.
A small leakage of liquid from the battery cells may occur
under extreme usage, charging or temperature conditions.
This does not indicate a failure. However, if the outer seal is
broken and this leakage gets on your skin.
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or
vinegar.
c. If the battery liquid gets in your eyes, flush them with
clean water for a minimum of 10 minutes and seek
immediate medical attention.
The RBRC seal on the Li-Ion battery pack indicates that the cost to recycle the battery pack at the end of its useful life has
already been paid by The Great States Corporation/American Lawn Mower Company. It is illegal to place spent Li-Ion batteries
in the local municipal solid waste or in the trash. RBRC in cooperation with The Great States Corporation/American Lawn Mower
Company has provided an environmentally friendly and easy way to recycle spent Li-Ion batteries. Just contact your local
recycling center or call 1.800.8.BATTERY for information on where to drop off the spent battery.
TO CHARGE - SEE CHARGER MANUAL FOR COMPLETE INSTRUCTIONS
BATTERY DISPOSAL
Remove the battery pack from the tool, cover the terminals with heavy duty adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any components. This product contains lithium-ion batteries which must be recycled or
disposed of properly. Local, state or federal laws may prohibit disposal of these batteries in the municipal solid waste or rural
trash pick up systems.
Battery
Pack
Constant Red + Flash Green = Battery is charging
Constant Red + Constant Green = Battery is fully charged
Charger
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
DANGER:
Before performing any maintenance, make sure the
battery is removed from the battery compartment and the
switch key is removed. Failure to heed this warning could
result in serious personal injury.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc., come
in contact with plastic parts. Chemicals can damage,
weaken, or destroy plastic which may result in serious
personal injury.
WARNING:
Always protect hands by wearing heavy gloves and/or
wrapping the cutting edges of the blade with rags and
other material when performing blade maintenance.
Failure to heed this warning could result in serious
personal injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types
of commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, dust, oil, grease,
etc.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If environment is dusty, also wear a dust mask.
REPLACING THE CUTTING BLADE
See figures 16
NOTES: Only use identical replacement blades.
Stop the motor and remove the switch key. Allow the
blade to come to a complete stop. Remove battery
from the battery compartment.
Turn the mower on its side
Wedge a block of wood between the blade and mower
deck to prevent the blade from turning.
Loosen the blade nut (1) using a wrench or socket
(not provided). Turn the nut COUNTERCLOCK WISE
to loosen it.
Remove the blade nut (1), spacer (2), blade insulator
(3), and blade (4).
To re-install the blade, position the blade with the
cutting edges toward the ground. Replace the blade
insulator and spacer, then thread the blade nut on the
shaft and finger tighten.
NOTE: Make certain all parts are replaced in the exact
order in which they were removed. When installing
the cutting blade, verify that it is installed with the curved
ends pointing toward the mower deck, and not toward the
ground.
Torque the blade nut down CLOCKWISE using a
torque wrench (not provided) to ensure the bolt is
properly tightened. The recommended torque for the
blade nut is 350-400 in. lbs.
Periodically check all nuts and bolts for proper
tightness to ensure safe operation of the mower.
Remove any buildup of grass and leaves on or around
the motor cover. Wipe the mower clean with a dry cloth
occasionally. Do not use water.
LUBRICATION
All of the bearings in this product are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further bearing lubrication is required.
At the beginning and end of each mowing season:
Lubricate the springs on the rear discharge door
with light oil.
Lubricate the height adjustment lever and related
hardware with light oil.
Remove the wheels and lubricate the surface of
the axle bolt and the inner surface of the wheel
with light oil.
Remove the blade and blade hub assembly and
lubricate the motor shaft with light oil or engine oil.
See Replacing the Cutting Blade for instructions
on removing the blade.
MAINTENANCE
1
2
3
4
16
Model 60062S
Fig. 16
SHARPENING THE BLADE
See Figure 17
For best mowing performance, the mower blade must
be kept sharp. A dull blade does not cut grass evenly
and overloads the motor. Under normal circumstances,
sharpening the blade twice during the mowing season
is usually sufficient. However, if your lawn has sandy
soil, more frequent sharpening's may be required.
Following the instructions in the Replacing the
Cutting Blade section, remove the mower blade.
DO NOT attempt to sharpen the blade while it is
attached to the mower.
Using a fine tooth file or stone, sharpen cutting
edges on both ends of the blade, removing equal
amounts of material from both ends.
BALANCING THE BLADE
See Figure 18
When sharpening, care should be taken to keep the
blade balanced. An unbalanced blade will cause
excessive vibration when the mower is running. This
vibration will eventually cause damage to the mower,
especially the motor.
To check blade balance:
Clamp a screwdriver horizontally in a vise as
shown.
NOTE: If a vise is not available, a straight nail can also
be used.
Place the center hole of blade on the screwdriver
(or nail) shank.
WARNING:
When removing, inspect the blade carefully. If blade is bent
or damaged, replace immediately with a new blade. Failure
to replace a bent or damaged blade could cause an accident
resulting in possible serious injury.
BATTERY MAINTENANCE
It is recommended to charge the mower every 3
months for optimum performance when not in use. If
the battery has been in storage for a long time without
recharging, it will be in a low charge state.
MAINTENANCE
If blade is balanced, it will remain in a horizontal
position. If either end of the blade drops downward,
sharpen the heavy side until the blade is balanced.
REPLACING WHEELS
See Figure 19
To Replace a wheel:
Stop the motor and remove the switch key.
Remove battery from the battery compartment.
Turn the mower on its side.
Using a flat blade screwdriver, pry off the hubcap
(1).
Remove the self-locking nut (2) from the wheel axle
(3), then remove the wheel (4).
Replace with new wheel and install new
self-locking nut (2) securely.
Replace hubcap (1).
Fig. 17
Fig. 18
17
Model 60062S
Fig. 19
1
2
3
4
STORING THE MOWER
See Figure 20
Remove the switch key and battery, and store in a
secure location out of the reach of children.
Before storage, wipe any dirt or debris from the
battery area.
Turn mower on its side and clean grass clippings that
have accumulated on the underside of the mower
deck.
Wipe the mower clean with a dry cloth.
Check all nuts, bolts, knobs, screws, fasteners, etc.,
for tightness.
Inspect moving parts for damage, breakage and wear.
Have repairs made on any damaged or missing parts.
Store mower indoors in a clean, dry place out of the
reach of children.
Do not store near corrosive materials such as fertilizer
or rock salt.
The handle assembly can be folded completely for
storage:
1. Remove the grass catcher.
2. Open the handle locking clamps and fully recess the
upper handle to the compact position.
3. Hold the handle with one hand.
4. Press and hold the quick adjust lever with your other
hand to release the handle.
5. Gently pivot the handle toward the front of the mower;
release the quick-adjust lever and continue to pivot
the handle until you hear and feel the lock pin engage
in the locked storage position.
6. Store the mower upright or flat.
WARNING:
USE EXTREME CAUTION WHEN FOLDING THE
HANDLE. THE CORD CAN BE DAMAGED IF
PINCHED BETWEEN HANDLE SECTIONS
CREATING A SAFETY HAZARD.
MAINTENANCE
18
Model 60062S
Fig. 20
WARNING:
WHEN THE HANDLE IS FOLDED, DO NOT
ATTEMPT TO START THE MOWER. WHEN
STORING THE MOWER IN THE VERTICAL
POSITION, POSITION THE MOWER SO THAT THE
BLADE IS FACING A WALL. FAILURE TO HEED
THESE WARNINGS CAN LEAD TO SERIOUS
PERSONAL INJURY.
WARNING:
IF THE MOWER TIPS OVER FROM THE UPRIGHT
POSITION, MOWER DAMAGE OR PERSONAL
INJURY MAY RESULT. ALWAYS KEEP THE
MOWER STABLE AND OUT OF THE REACH OF
CHILDREN WHEN IT IS IN THE UPRIGHT POSITION.
IF POSSIBLE, LAY IT FLAT FOR STORAGE.
Problem Possible cause Solution
The mower fails to start. The safety key is not inserted in the slot.
The battery pack is depleted.
The battery pack is not attached to the mower.
The battery pack is on the wrong side.
Battery or mower circuitry is too hot.
The upper handle is not extended to their
maximum length.
The handle is not set at one of the operating
positions.
Mower deck is clogged with grass and debris.
Insert the safety key.
Charge the battery pack.
Attach the battery pack to the mower.
Move the battery pack to the correct side of the
battery compartment.
Allow the battery pack or mower to cool down.
Fully extend the handle and lock the clamps.
Adjust the handle to the one of the operating
positions.
Clean the mower deck and make certain that the
blade has freedom of movement.
The mower cuts unevenly. Dull blade.
The cutting height is not set properly.
The blade is assembled incorrectly.
Sharpen or replace blade.
Raise the blade to a higher setting.
Reassemble the blade, following the section
"Replacing the Cutting Blade" in this manual.
Mower stops while
mowing.
The battery pack is depleted.
Mower is in overload condition.
Mower deck is clogged with grass and debris.
Battery or mower circuitry is too hot.
The upper handle is retracted a little by the
pushing force applying on the handle.
Charge the battery pack.
Raise cutting height or slow down the mowing.
Unclog mower deck. Raise cutting height, or cut a
narrow swath.
Allow the battery pack or mower to cool down.
Unlock the clamps. Fully extend the upper handle
and lock the clamps again.
Mower does not mulch
properly.
Wet grass clippings are sticking to the
underside of the deck.
Mulching plug is missing.
The mower is set to cut too much grass.
Wait until the grass dries before mowing.
Install the mulching plug.
Raise the blade to a higher setting.
Excessive vibration. Cutting blade is loose.
Cutting blade is unbalanced.
Bent cutting blade.
Bent motor shaft.
Tighten the blade bolt.
Balance the blade following the instructions.
Replace the blade.
Contact the service center at 1-800-618-7474.
The handle locking clamps
can not be closed in position.
The upper handle is not fully extended. Fully extend the upper handle, then lock the
clamps.
TROUBLESHOOTING
19
Model 60062S
20
Model 60062S
PARTS AND SERVICE
For parts or service, please call 1-800-618-7474 or visit us online at
scotts.americanlawnmower.com. Be sure to provide all relevant information when you
call or visit.
REPAIR PARTS (KITS/ ITEMS)
The model number of this tool is found on a plate or label attached to the housing.
Please record the serial number in the space provided below.
MODEL NUMBER___60062S _____
SERIAL NUMBER_______________
Always mention the model number when ordering kits/items for this tool.
No. Kit/ Item Number Description
1 LM62-HK-1 Handle Locking Clamps
2 LM62-FWK-2 Front Wheel Kit
3 LM62-RWK-2 Rear Wheel Kit
4 LM62-HA-1 Wheel Height Adjuster Kit
5 LM62-BK-1 Mower Blade Kit
6 LM62-RDK-1 Rear Door Kit
7 LM62-SDD-1 Side Discharge Flap
8 LM62-SDC-1 Side Discharge Chute
9 LM62-MP-1 Mulching Plug Kit
10 LM62-KEY-1 Switch Key Kit
11 LM62-GC-1 Grass Catcher Kit
12 LM62-RFK-1 Rear flap Kit
13 BL86250 62V 5.0Ah Battery
14 CHL86200 62V Charger
CALL US FIRST !!
Call us first with questions about operating or maintaining your product
at 1.800.618.7474 between 8:00 a.m. – 5:00 p.m. Eastern Standard Time,
or get assistance on scotts.americanlawnmower.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66

Scotts 60062S Le manuel du propriétaire

Catégorie
Tondeuses à gazon
Taper
Le manuel du propriétaire

dans d''autres langues