Sony CDP-D500 Manuel utilisateur

Taper
Manuel utilisateur
3-858-870-13 (1)
1996 by Sony Corporation
Operating Instructions
Mode d’emploi
Bedienungsanleitung
EN
F
D
CDP-D500
2
EN
WARNING
To prevent fire or shock
hazard, do not expose
the unit to rain or
moisture.
To avoid electrical shock,
do not open the cabinet.
Refer servicing to
qualified personnel only.
For the customers in Europe
The laser component in this product
is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as a CLASS 1
LASER product. The CLASS 1 LASER
PRODUCT MARKING is located on the
rear exterior.
The following caution label is located
inside of the unit.
WARNING
This equipment has been tested and
found to comply with the limits for a
Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
when the equipment is operated in a
commercial environment. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instruction manual, may cause
harmful interference to radio
communications. Operation of this
equipment in a residential area is likely
to cause harmful interference in which
case the user will be required to correct
the interference at his own expense.
You are cautioned that any changes or
modifications not expressly approved in
this manual could void your authority to
operate this equipment.
Owner’s Record
The model and serial numbers are
located at the rear of the unit.
Record the serial number in the space
provided below. Refer to them whenever
you call upon your Sony dealer
regarding this product.
Model No. CDP-D500
Serial No. _________________________
For the customers in Canada
CAUTION
TO PREVENT ELECTRIC SHOCK,
DO NOT USE THIS POLARIZED AC
PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
For the customers in the United States
This symbol is intended to alert
the user to the presence of
uninsulated “dangerous voltage”
within the product’s enclosure
that may be of sufficient
magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert
the user to the presence of
important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
Getting Started
EN
3
EN
Getting Started
Unpacking........................................................................................................ 4
Rack Mounting ................................................................................................ 4
Hooking Up the System ................................................................................. 4
Playing CDs
Basic Operation ............................................................................................... 8
Using the Display ........................................................................................... 8
Locating a Specific Track ............................................................................... 9
Locating a Particular Point in a Track ....................................................... 10
Playing Tracks Repeatedly ..........................................................................10
Creating Your Own Program (Program Play) .......................................... 11
Fading In or Out............................................................................................12
Setting the Cue Point in a Track (Rehearsal) ............................................13
Playing a Track From the Very Beginning (Auto Cue) ...........................14
Standing by at the Starting Point (Cue Standby) .....................................14
Pausing at Each Track (Auto Pause) ..........................................................15
Changing the Playing Speed (Variable Speed Play) ................................ 15
Playing in Random Order (Shuffle Play) Z .............................................16
Playing Only Specific Tracks (Delete Play) Z ......................................... 16
Playing Using a Timer.................................................................................. 17
Last Mode Memory ...................................................................................... 17
Additional Operation
Setting the Menu Options ............................................................................ 18
Additional Information
Precautions .................................................................................................... 19
Notes on CDs ................................................................................................. 19
Troubleshooting ............................................................................................20
Specifications ................................................................................................. 20
Index
Index ............................................................................................................... 22
TABLE OF CONTENTS
Welcome!
Thank you for purchasing the Sony
Compact Disc Player. Before operating
the unit, please read this manual
thoroughly and retain it for future
reference.
About This Manual
The instructions in this manual are for
model CDP-D500.
Conventions
Instructions in this manual describe
the controls on the player.
You can also use the controls on the
remote commander if they have the
same or similar names as those on the
player.
The following icons are used in this
manual:
Indicates that you can do the
task using the remote
commander.
Indicates hints and tips for
making the task easier.
Getting Started
4
EN
Unpacking
Check that you received the following items:
AC power cord (1)
Remote commander (1)
Sony SUM-3 (NS) batteries (2)
Screws (M5 × 12) (4)
Decorative washers (4)
Inserting batteries into the remote
commander
You can control the player using the supplied remote
commander.
Insert two size AA (R6) batteries by matching the +
and on the batteries. When using the remote
commander, point it at the remote sensor in the left of
the display on the player.
Rack Mounting
You can install the player in an EIA standard 19-inch
rack. Be sure to turn off the player before you install it.
Remove the foot bases from the player. Then insert the
player into the rack, and secure it with the supplied
decorative washers and screws (M5 × 12).
Getting Started
Rack
Decorative washer
Screw (M5 × 12)
When to replace batteries
With normal use, the batteries should last for about six
months. When the remote commander no longer
operates the player, replace all the batteries with new
ones.
Notes
Do not leave the remote commander near an extremely hot
or humid place.
Do not drop any foreign object into the remote casing,
particularly when replacing the batteries.
Do not expose the remote sensor to direct sunlight or
lighting apparatuses. Doing so may cause a malfunction.
If you dont use the remote commander for an extended
period of time, remove the batteries to avoid possible
damage from battery leakage and corrosion.
Note
Do not attach the foot base screws back to the player. It may
damage inside of the player.
Be sure to keep the foot bases and screws.
Hooking Up the System
Overview
This section describes how to hook up the CD player to
other audio components. Be sure to turn off the power
of each component before making the connections.
ANALOG OUT
(UNBALANCE)
ANALOG OUT
(BALANCE)
REMOTE
(8P)
DIGITAL OUT
DIGITAL OUT
(AES/EBU)
EXT SYNC
RS-232C
Getting Started
5
EN
Getting Started
What cords will I need?
pWhen making analog hookups
Audio cord (RK-C505KS/510KS/515KS, not supplied) (1)
Analog audio component
(analog mixer, analog
VTR, analog tape
recorder or amplifier)
Analog audio cannon cables (EC-0.5XLR2/5XLR2/
10XLR2, not supplied) (2)
pWhen making digital hookups
Coaxial digital connecting cable (VMC-1ES/3ES/5ES, not
supplied) (1)
White
(L)
White
(L)
Red
(R)
Red
(R)
Digital audio component
(digital mixer, DAT,
digital audio recorder or
digital VTR)
External synchronizing
system (digital mixer or
clock signal generator)
Digital audio cannon cable (ECD-3C/10C/30C, not
supplied) (1)
Hookups
pWhen making analog hookups
When connecting with an audio cord
Connect a component to the ANALOG OUT
(UNBALANCE) jacks.
Be sure to match the color-coded cord to the
appropriate jacks on the components: Red (right)
to Red and White (left) to White. Be sure to make
connections firmly to avoid hum and noise.
CD player
Analog mixer, etc.
UNBALANCE
CH-1(L)
BALANCE
CH-1(L) CH-2(R)
CH-2(R)
ANALOG OUT
CD
L
R
INPUT
Fader start system
(compact disc fader unit
or mixing console)
Personal computer or
work station
To an AC outlet
CD player
Getting Started
6
EN
When connecting with analog audio cannon cables
Connect a component to the ANALOG OUT
(BALANCE) connectors.
When connecting with a digital audio cannon cable
Connect a component to the DIGITAL OUT (AES/
EBU) connector.
a)
b)
pWhen making digital hookups
When making these connections, you cannot use the
fading in or out function (page 12).
When connecting with a coaxial digital connecting
cable
Connect a component to the DIGITAL OUT
connector.
CD player
ANALOG INPUT
CH-1(L) CH-2(R)
UNBALANCE
CH-1(L)
BALANCE
CH-1(L) CH-2(R)
CH-2(R)
ANALOG OUT
CD player
DIGITAL OUT
AES/EBU
DIGITAL INPUT
COAXIAL
Digital mixer, etc.
a) To plug in the cables, match these positions and insert
the cables firmly.
b) To detach the cables, pull the cables out while pressing
the lock button.
a)
b)
a) To plug in the cables, match these positions and insert
the cables firmly.
b) To detach the cables, pull the cables out while pressing
the lock button.
Connecting a personal computer or work station
You can control the player with a computer by
connecting your personal computer or work station.
Connect the equipment to the RS-232C connector using
a D-Sub cable.
For details on setting of the RS-232C connector, see
Setting the Menu Options on page 18.
If you have CD-TEXT discs
The player can read the information stored on CD-TEXT
discs. When making this connection, the player transmits
the CD-TEXT information to your personal computer or
work station.
Analog mixer, etc.
CD player
Digital mixer, etc.
DIGITAL OUT
AES/EBU
DIGITAL INPUT
AES/EBU
132
Pin Polarity
1: GND
2: HOT
3: COLD
Getting Started
7
EN
Getting Started
Connecting the AC power cord
Connect the AC power cord (supplied) to AC IN on the
rear panel and connect the other end to a wall outlet.
PARALLEL
SERIAL
REMOTE SELECT
Connecting a fader start system
By connecting a fader start system to the REMOTE (8P)
connector on the rear panel of the player, you can fade
the sound in or out by remote control at the desired
point on a disc.
Connecting an external synchronizing system
By connecting an external synchronizing system, the
player operates on the clock frequency transmitted
from the system.
1 Connect an external synchronizing system to the
EXT SYNC connector.
2 Input the clock signal of 44.1 kHz TTL level.
3 Set EXT SYNC ON/OFF to ON.
When you don't use the external synchronizing
system, set the switch to OFF.
Setting the REMOTE SELECT switch
Set REMOTE SELECT on the front panel of the player
to activate the connector(s) for the equipment you
want to use.
Connector
RS-232C
REMOTE (8P)
Both RS-232C and
REMOTE (8P)
Set the switch to
SERIAL
PARALLEL
the center position
Playing CDs
8
EN
Playing CDs
Using the Display
You can check information about the disc using the
display.
Basic Operation
Before you begin, make sure you have connected the
player and other component correctly and firmly as
indicated on pages 46.
POWER
6 OPEN/CLOSE
(
TIME/SPEED
Checking the total number and playing
time of the tracks
Press TIME/SPEED before you start playing.
The display shows the total number of tracks, total
playing time and music calendar.
TRACK MIN SEC
CONTINUE
FADE
1‚ 4528
21345
768910
Total number of
tracks
Total playing time
Music calendar
If the disc has more than 20 tracks, the indication
appears next to 20 in the music calendar.
The information also appears when you press the
6 OPEN/CLOSE button to close the disc tray.
Display information while playing a disc
While playing a disc, the display shows the current
track number, elapsed time and the music calendar.
The track numbers in the music calendar disappear
after they are played.
TRACK INDEX MIN SEC
CONTINUE
FADE
21345
768910
1 1 156
Elapsed time
Music calendar
Current track
number
1 Turn on the connected component.
2 Press POWER to turn on the player.
3 Press 6 OPEN/CLOSE, and place a disc on the
disc tray with the label side up.
4 Press (.
The disc tray closes and the player plays all the
tracks once (Continuous Play).
You can also start play by turning the SHUTTLE
ring clockwise.
Note
When you play CD-TEXT discs, it may take longer than
normal discs to start playing after the disc tray closes.
To stop play
Press p.
When you want to
Pause
Resume play after pause
Go to the next track
Go back to the previous track
Stop play and remove the disc
Press
P
P or (
+ or turn the JOG dial
clockwise
= or turn the JOG dial
counterclockwise
6 OPEN/CLOSE
When you listen with headphones
Connect your headphones to the PHONES jack. You can
adjust the volume with the PHONE LEVEL control.
If play doesn't start from the first track
Press CONTINUE.
Playing CDs
9
EN
Playing CDs
Locating a Specific Track
You can quickly locate any track while playing a disc
using the =/+ (AMS: Automatic Music Sensor)
buttons or number buttons.
To locate
The next or
succeeding tracks
The current or
preceding tracks
A specific track
directly
Press
+ repeatedly or turn the JOG dial
clockwise until you find the track
= repeatedly or turn the JOG dial
counterclockwise until you find the
track
Number button of the track
Changing the display information
Each time you press the TIME/SPEED button while
playing a disc, the display changes as shown in the
chart below.
When you directly locate a track numbered over 12
(or 10 when using the remote commander)
Press >10 first, then the corresponding number buttons.
To enter 0, use button 10.
Example: To play track number 30
Press >10 first, then 3 and 10.
You can locate an index
You can locate an index as well as a track, using the
=/+ buttons. To locate an index, set Cueing Select
of menu options to CUEING IDX. For details, see page
18.
Press
Elapsed time
and number of
the current track
Remaining time
on the current
track
Remaining time
on the disc
Elapsed time of
the current track
with frame
number
Playing speed
(see page 15)
Press
Press
Press
Press
Number buttons >10
TRACK INDEX MIN SEC
CONTINUE
FADE
21345
768910
1 1 156
TRACK INDEX MIN SEC
CONTINUE
FADE
21345
768910
1 1 -157
TRACK INDEX MIN SEC
CONTINUE
FADE
21345
768910
1 -4332
CONTINUE
FADE
21345
768910
‚:58:23
CONTINUE
FADE
21345
768910
SPEED ‚.‚
JOG dial
=/+
Playing CDs
10
EN
Locating a Particular Point in a
Track
You can search for a particular point in a track while
playing a disc.
Playing Tracks Repeatedly
You can play tracks repeatedly in any play mode.
Press REPEAT while playing a disc.
REPEAT appears in the display. The player repeats
the tracks as follows:
When the disc is played in
Continuous Play (page 8)
Shuffle Play (page 16)
Program Play (page 11)
Delete Play (page 16)
Delete Shuffle Play
(page 16)
The player repeats
All the tracks
All the tracks in random order
The same program
All the remaining tracks
All the remaining tracks in
random order
To cancel Repeat Play
Press REPEAT repeatedly until REPEAT disappears from
the display.
Repeating the current track
You can repeat only the current track in any play
mode.
While the track you want is being played, press
REPEAT repeatedly until REPEAT 1 appears in the
display.
0/)
To search for
A point while
monitoring the sound
A point quickly by
observing the display
during pause
A point using the
SHUTTLE ring
You need to
Press ) (forward) or 0 (backward)
and hold down until you find the
point
Press 0/) and hold down until
you find the point. You will not hear
the sound during the operation.
Turn the SHUTTLE ring and hold until
you find the point. The search speed
increases as you turn the SHUTTLE
ring further.
Note
If - OVER - appears in the display, the disc has reached the
end while you were pressing the ) button or turning the
SHUTTLE ring clockwise. Press 0 or turn the SHUTTLE
ring counterclockwise to go back.
REPEAT A-B
SHUTTLE ring
Playing CDs
11
EN
Playing CDs
Repeating a specific portion
(A˜B Repeat)
You can play a specific portion in a track repeatedly.
This might be useful when you play a music
instrument or memorize lyrics.
Note that you cannot repeat a portion extending to two
tracks.
1 While playing a disc, press A-B when you find the
starting point (point A) of the portion to be played
repeatedly.
A- flashes in the display.
2 When you reach the ending point (point B), press
A-B again.
A-B lights up in the display and the player plays
this specific portion repeatedly.
To cancel A˜B Repeat
Press REPEAT.
Setting a new starting point
You can move the repeated portion forward by
changing the starting point.
1 Press A-B while the player is repeating the specific
portion.
The ending point B becomes the new starting point
A. A- flashes in the display.
2 When you reach the new ending point, press A-B
again.
A-B appears. The player repeats between the
new starting and ending points.
When you want to restart from the starting point A
Press ( during A˜B Repeat.
1 Press PROGRAM.
PROGRAM appears in the display.
2 Press the number buttons of the tracks you want to
program in the order you want.
To program tracks numbered over 12 (or 10 when
using the remote commander), use the >10 button
(see page 9).
Creating Your Own Program
(Program Play)
You can arrange the order of the tracks on a disc and
create your own program. The program can contain up
to 24 tracks.
PROGRAM
CLEAR
>10
(
p
CHECK
Number buttons
If youve made a mistake
Press CLEAR, then press the correct number button.
3 Press ( to start Program Play.
To cancel Program Play
Press CONTINUE.
When tracks, which arent numerically consecutive on
the disc, are programmed consecutively (i.e. 1, 3, 5
etc.)
A one-second access time blank is added between the
tracks.
Last programmed track
Total playing time
Programmed tracksPlaying order
TRACK STEP MIN SEC
PROGRAM
FADE
25
8
5 3 1318
Playing CDs
12
EN
You can check how a track will affect the total
playing time of the program (Program Edit)
To select a track, turn the JOG dial or press =/+
and check the total playing time. Then press PROGRAM
to confirm your selection.
The program remains even after the Program Play
ends
When you press the ( button, you can play the same
program again.
Notes
•“. –– appears instead of the total playing time in the
display when it exceeds 100 minutes.
•“PGM FULL appears in the display when you try to add a
track to a program which already contains 24 tracks.
Checking the track order
You can check your program before or after you start
playing.
Press CHECK.
Each time you press this button, the display shows the
track number in the programmed order. After the last
track in the program, the display shows - END - and
returns to the original display. If you check the order
after you start playing, the display shows only the
remaining track numbers.
Changing the track order
You can change your program before you start playing.
To
Erase a track
Erase the last track in the
program
Add tracks to the end of the
program
Change the whole program
completely
Fading In or Out
You can manually fade the sound in or out to prevent
tracks from starting or ending abruptly.
Note that you cannot use this effect when you use the
DIGITAL OUT jack or connector.
Press FADER
During pause. The
FADE
indication
flashes and play fades in.
When you want to start fading out.
The
FADE
indication flashes. The
play fades out and the player
pauses.
You can fade in or out by remote control
Connect a fader start system to the REMOTE (8P)
connector on the rear panel of the player (see
Connecting a fader start system on page 7).
Changing the fading time
You can change the fading time from 1 to 9 seconds
before fading in or out. The fading time is factory set to
5 seconds.
1 Press FADER before you start playing.
2 Press 0/) or turn the JOG dial to specify the
fading time.
To
Start play fading in
End play fading out
JOG dialFADER0/)
Press
CHECK until the track you
dont want appears in the
display, then press CLEAR
CLEAR. Each time you press
the button, the last track will
be cleared.
Number buttons of the tracks
to be added
p (stop). Create a new
program following the
programming procedure.
Playing CDs
13
EN
Playing CDs
Setting the Cue Point in a
Track (Rehearsal)
You can play a portion of a track repeatedly to help
you find the cue point. While searching for the point,
the display shows the elapsed time with frame number
so you can set the point accurately.
3 Press ENTER when you find the cue point.
RHSL END appears in the display and the
player pauses at that point.
To resume play
Press ( or P.
Changing the repeating time
When searching for the cue point, you can change the
amount of time the player repeats from 1 to 9 seconds.
The repeating time is factory set to 2 seconds.
You can also change the repeating time before you start
searching
1 Press REHEARSAL until LOOP * SEC appears
in the display.
2 Turn the JOG dial until the repeating time you
want appears in the display.
Changing the shift increment
When shifting the starting point to be played
repeatedly, you can change the increment from 1 to 74
frames. The shift increment is factory set to 24 frames.
You can also change the shift increment before you
start searching.
1 Press REHEARSAL until ** FR/CLK appears in
the display.
2 Turn the JOG dial until the number of frames you
want appears in the display.
JOG dial
ENTER
REHEARSAL
=/+
PROGRAM REHEARSAL
FADE
2
‚:21:13
Playing time with frame number
Track number being played
1 While playing a disc, press REHEARSAL just
before the cue point you want to set.
REHEARSAL appears in the display and the
player plays the next few seconds repeatedly.
2 If you want to shift the starting point forward, turn
the JOG dial clockwise or press +.
To shift the starting point backward, turn the JOG
dial counterclockwise or press =.
Each change in the JOG dial position or press of
the =/+ buttons shifts the starting point.
+ or ”–” appears before the playing time when
you change the starting point.
CONTINUE
REHEARSAL
FADE
2
+ ‚:21:37
New starting point
CONTINUE
FADE
21345
768910
LOOP 2 SEC
CONTINUE
FADE
21345
768910
24 FR/ CLK
Shift increment
Repeating time
Playing CDs
14
EN
Standing by at the Starting
Point (Cue Standby)
You can go back to the starting point in the current
track and stand by there.
Playing a Track From the Very
Beginning (Auto Cue)
You can skip the lead-in portion of a track and start
playing from where the sound actually begins. This is
useful when, for example, you want to add music to a
video tape.
AUTO CUE/PAUSE
(
P
Number buttons
>10
1 Set AUTO CUE/PAUSE to A.CUE.
AUTO CUE appears in the display.
2 Press P.
3 Press the number button of the track you want.
The player locates the very beginning of the sound
in the track.
4 Press ( or P to start playing.
To cancel Auto Cue
Set AUTO CUE/PAUSE to OFF.
You can change the Auto Cue point level (threshold
level)
The player is factory set to detect the Auto Cue point of
each track where the sound louder than 60 dB begins.
You can select the Auto Cue point among 5 levels. For
details, see Setting the Menu Options on page 18.
CUE/STBY
Press CUE/STBY while playing a disc.
The player pauses at the point as follows:
When the AUTO CUE/
PAUSE switch is set to
OFF
A.CUE (page 14)
A.PAUSE (page 15)
When you started play using the Rehearsal function
The player pauses at the cue point you set (see Setting the
Cue Point in a Track on page 13). If you press the CUE/STBY
button while playing a track other than the one in which you
have set the cue point, the player pauses at the beginning of
the current track.
The player pauses at
The beginning of the current
track
The point where the sound of the
current track actually begins
The beginning of the current
track
Playing CDs
15
EN
Playing CDs
Pausing at Each Track
(Auto Pause)
You can set the player to pause at the beginning of the
next track each time a track is finished playing.
This is useful when, for example, you want to record
only one track or several tracks out of order (i.e. 1, 3, 5
etc.).
Set AUTO CUE/PAUSE to A.PAUSE.
AUTO PAUSE appears in the display.
To resume play
Press ( or P.
To cancel Auto Pause
Set AUTO CUE/PAUSE to OFF.
Changing the Playing Speed
(Variable Speed Play)
You can adjust the playing speed within ± 12.5% of the
normal speed. As the playing speed changes, the pitch
also changes.
AUTO CUE/PAUSE
VARI SPEED ON/OFF
VARI SPEED control
1 While playing a disc, press VARI SPEED ON/OFF
until VARI SPEED lights up in the display.
SPEED *.* appears in the display.
2 Turn the VARI SPEED control to select the desired
speed.
The playing speed changes in 0.1% increment.
To reset the playing speed
Push the VARI SPEED control while the display shows the
playing speed.
To cancel Variable Speed Play
Press VARI SPEED ON/OFF.
If you want to play the disc again with the speed you set,
press VARI SPEED ON/OFF.
Note
When using the external synchronizing system (see page 7),
the playing speed does not change.
CONTINUE
VARI SPEED
FADE
21345
768910
SPEED ‚.‚
Playing speed
Playing CDs
16
EN
Playing in Random Order
(Shuffle Play) Z
You can have the player shuffle tracks and play in
random order.
Playing Only Specific Tracks
(Delete Play) Z
You can delete unwanted tracks and play only the
remaining tracks.
1 Press SHUFFLE on the remote commander.
SHUFFLE appears in the display for a while.
2 Press ( to start Shuffle Play.
The
indication appears while the player is
shuffling the tracks.
To cancel Shuffle Play
Press CONTINUE.
You can start Shuffle Play while playing
Press SHUFFLE on the remote commander, and Shuffle
Play starts from the current track.
You can delete unwanted tracks during Shuffle Play
(Delete Shuffle Play)
Press the number button of the track you want to delete.
The track number and DELETE appear in the display,
then the track number disappears from the music
calendar.
If you want to restore the track, press the number button
again.
To restore all the tracks, press p in stop mode.
(
SHUFFLE
SHUFFLE
Number buttons
CONTINUE
>10
(
1 Press SHUFFLE on the remote commander.
SHUFFLE appears in the display for a while.
2 Press the number buttons of the tracks you want to
delete.
The track numbers disappear from the music
calendar and DELETE appears for a while.
To delete a track numbered over 10, use the >10
button (see page 9).
If youve made a mistake
Press the number button of the track. SELECT appears
in the display and the track will be restored.
3 After youve deleted all the tracks you dont want,
press CONTINUE.
CONTINUE appears in the display.
4 Press ( to start Delete Play.
To cancel Delete Play
Press p in stop mode.
The player keeps the deleted tracks in memory even
after the Delete Play ends
When you press the ( button, you can play only the
remaining tracks again.
You can play the tracks in random order (Delete
Shuffle Play)
Just skip Step 3 in the above procedure.
You can delete a track while playing
Press CLEAR while the track is being played. The player
deletes the track and starts playing the next track.
Playing CDs
17
EN
Playing CDs
Playing Using a Timer
You can start playing a disc at any time you want by
connecting a timer (not supplied). Please also refer to
the instructions for the timer if you need help.
Last Mode Memory
The player remembers the settings last time you used
the player even if you turn off the player. When you
turn on the player again, the player is ready to play the
disc in the same way. The player remembers the
following settings:
Play mode (Continue [page 8], Program* [page 11]
or Shuffle [page 16])
Repeat mode (Repeat, Repeat 1 or Repeat off [page
10])
Fading time (page 12)
Repeating time of the Rehearsal function (page 13)
Shift increment of the Rehearsal function (page 13)
Playing speed (page 15)
Setting of the VARI SPEED ON/OFF button (page
15)
* The player remembers the programmed tracks unless you
replace the disc. When you turn on the player again, you
can play the same program.
The player also remembers all the menu option
settings. For details on menu options, see page 18.
TIMER
1 Set TIMER on the player to PLAY.
2 Set the timer to the time you want.
The player turns off. When the set time comes, the
player turns on and starts playing.
3 When you are finished using the timer, set TIMER
on the player to OFF.
Additional Operation
18
EN
Setting the Menu Options
The player has 8 menu options as follows:
1 Key Protect
You can make the controls on the player ineffective
except for the EJECT, STOP, ENTER and CLEAR
buttons.
2 Remote Protect
You can make the supplied remote commander
ineffective.
3 Auto Cue threshold level
You can change the cue point level of the Auto Cue
function (see page 14).
4 Cueing Select
You can select what you want to locate (track or
index) by using the =/+ buttons.
58 RS-232 baudrate/data/stop/parity
When you connect your personal computer or
work station to the RS-232C connector (see page 6),
you can set each option.
The following menu choices are available for each
option. The initial settings are indicated with
underline:
* If you press a button on the player after setting the option
to LOCAL OFF, PROTECTED appears in the display.
Menu options
Key Protect*
Remote Protect
Auto Cue threshold
level
Cueing Select
RS-232 baudrate
RS-232 data
RS-232 stop
RS-232 parity
Select
LOCAL ON to make the controls
effective.
LOCAL OFF to make the controls
ineffective.
RM ENABLE to make the remote
commander effective.
RM DISABLE to make the remote
commander ineffective.
Among ACUE 72DB, ACUE 66DB,
ACUE 60DB, ACUE 54DB and
ACUE 48DB
CUEING TRK to locate a track.
CUEING IDX to locate an index.
Among BAUD 1200, BAUD 2400,
BAUD 4800, BAUD 9600, BAUD 19200
and BAUD 38400
DATA 8 BIT or DATA 7 BIT
STOP 1 BIT or STOP 2 BIT
Among PARITY OFF, PARITY ODD
and PARITY EV
JOG dial
ENTER
=/+
0/)
SHUTTLE ring
1 Press ENTER in stop mode.
2 Turn the SHUTTLE ring or press =/+ until
the display shows the menu option you want to
set.
The menu option number appears in the music
calendar.
3 Turn the JOG dial or press 0/) until the
desired setting flashes in the display.
4 Press ENTER to select the setting.
The selected setting lights up in the display.
5 Press ENTER again to return to the original
display.
To initialize all the settings
Press CLEAR while setting menus.
Additional Information
19
EN
Additional InformationAdditional Information
Notes on CDs
On handling CDs
To keep the disc clean, handle the disc by its edge. Do not
touch the surface.
Do not stick paper or tape on the disc.
Not this way
Do not expose the disc to direct sunlight or heat sources
such as hot air ducts, nor leave it in a car parked in direct
sunlight as there can be considerable rise in temperature
inside the car.
Do not use any commercially available stabilizer and/or
disc protector. If you do, the disc and the player may be
damaged.
After playing, store the disc in its case.
On cleaning
Before playing, clean the disc with a cleaning cloth. Wipe
the disc from the center out.
Precautions
On safety
Caution The use of optical instruments with this product
will increase eye hazard.
Should any solid object or liquid fall into the cabinet,
unplug the player and have it checked by qualified
personnel before operating it any further.
On power sources
Before operating the player, check that the operating
voltage of the player is identical with your local power
supply. The operating voltage is indicated on the nameplate
at the rear of the player.
The player is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet, even if
the player itself has been turned off.
If you are not going to use the player for a long time, be
sure to disconnect the player from the wall outlet. To
disconnect the AC power cord (mains lead), grasp the plug
itself; never pull the cord.
AC power cord must be changed only at the qualified
service shop.
On placement
Place the player in a location with adequate ventilation to
prevent heat build-up in the player.
Do not place the player on a soft surface such as a rug that
might block the ventilation holes on the bottom.
Do not place the player in a location near heat sources, or in
a place subject to direct sunlight, excessive dust or
mechanical shock.
On operation
If the player is brought directly from a cold to a warm
location, or is placed in a very damp room, moisture may
condense on the lenses inside the player. Should this occur,
the player may not operate properly. In this case, remove
the disc and leave the player turned on for about an hour
until the moisture evaporates.
On adjusting volume
Do not turn up the volume while listening to a portion with
very low level inputs or no audio signals. If you do, the
speakers may be damaged when a peak level portion is
played.
On cleaning
Clean the cabinet, panel and controls with a soft cloth
slightly moistened with a mild detergent solution. Do not
use any type of abrasive pad, scouring powder or solvent
such as alcohol or benzine.
If you have any questions or problems concerning your
player, please consult your nearest Sony dealer.
Do not use solvents such as benzine, thinner,
commercially available cleaners or anti-static spray
intended for vinyl LPs.
Additional Information
Additional Information
20
EN
Troubleshooting
If you experience any of the following difficulties while
using the player, use this troubleshooting guide to help
you remedy the problem. Should any problem persist,
consult your nearest Sony dealer.
Theres no sound.
/Check that the player is connected securely.
/Make sure you operate the connected
component correctly.
/Adjust the playback level using the PHONE
LEVEL control.
The CD does not play.
/Theres no CD inside the player (-NO DISC-
appears). Insert a CD.
/Place the CD with the label side up on the disc
tray correctly.
/Clean the CD (see page 19).
/Moisture has condensed inside the player.
Remove the disc and leave the player turned on
for about an hour (see page 19).
The remote commander does not function.
/Remove the obstacles in the path of the remote
commander and the player.
/Point the remote commander at the remote
sensor in the left of the display on the player.
/Replace all the batteries in the remote
commander with new ones if they are weak.
/Set the Remote Protect of menu options to RM
ENABLE (see page 18).
The controls on the player do not function.
/Set the Key Protect of menu options to LOCAL
ON (see page 18).
The player functions incorrectly.
/The microcomputer chips may be operating
incorrectly. Turn off the player and turn it on
again.
Specifications
Compact disc player
Frequency response 5 Hz to 20 kHz ± 0.3 dB (at 10 kilohms)
Signal-to-noise ratio More than 100 dB (20 kHz LPF, IHF-A
weight)
Dynamic range More than 98 dB
Harmonic distortion Less than 0.004% (1 kHz, 0 dB, 20 kHz
LPF)
Channel separation More than 100 dB (1 kHz, 20 kHz LPF)
Analog outputs
Connector
ANALOG OUT
(BALANCE)
ANALOG OUT
(UNBALANCE)
PHONES
Digital outputs
Connector
DIGITAL OUT
(AES/EBU)
DIGITAL OUT
(IEC-958)
Word input
Connector
EXT SYNC
INPUT
Type
XLR-3
Phono
jacks
Stereo
phone jack
Output
impedance
100 ohms
200 ohms
150 ohms
Maximum
output level
+24 dBs
+ 9 dBs
15 mW
Load
impedance
More than
10 kilohms
More than
10 kilohms
32 ohms
Type
XLR-3
Phono jacks
Load
impedance
110 ohms
75 ohms
Output
impedance
50 ohms
(balanced)
75 ohms
(unbalanced)
Type
BNC
Input level
2 V p-p
(TTL
level)
Input
frequency
44.1 kH
±12.5%
Input
impedance
22 kilohms/
75 ohms,
switchable
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Sony CDP-D500 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues