Admiral AAV7000AWW Manuel utilisateur

Marque: Admiral

Modèle: AAV7000AWW

Catégorie: Machines à laver

Taper: Manuel utilisateur

Washer

AAV-2

Table of Contents

Important Safety Instructions

1-2

Operating Tips ............ 1 1

Using the Controls

2 Speed Models ............ 3-4

3 Speed Models ............ 5-6

4 Speed Combo Models ....... 7-8

Special Features ......... 9-10

Care & Cleaning ........... 10

Troubleshooting ........... 12

Guide d'utilisation

et d'entretien .............. 14

Guia de uso y cuidado ..... 28

Form No. Y81897 A Part No. 2206665 www.maytag.com Lithe U.S.A. ,_,2006 Maytag Appliances Sales Co.

Importnn!SnfetyInstructions

Installer: Please leave this guide with this

appliance.

Consumer: Please read and keep this guide for

future reference. Keep sales receipt and/or canceled

check as proof of purchase.

Model Number

Serial Number

Date of Purchase

If you have questions, call:

Customer Assistance

1-800-688-9900 U.S.A.

1-800-688-2002 Canada

(Mon.-Fri. 8 a.m.-8 p.m. Eastern Time)

Internet: http://www.m aytag.com

U.S.A. Customers using TTY for deaf, hearing

impaired or speech impaired, call 1-800-688-2080.

In our continuing effort to improve the quality and

performance of our appliances, it may be necessary

to make changes to the appliance without revising

this guide.

For service information, see page 11.

What You Need to Know About

Safety Instructions

Warning and Important Safety Instructions appearing in

this guide are not meant to cover all possible

conditions and situations that may occur. Common

sense, caution and care must be exercised when

installing, maintaining or operating appliance.

Always contact the manufacturer about problems or

conditions you do not understand.

Recognize Safety Symbols, Words,

Labels

WARNING - Hazards or unsafe practices which COULD

result in severe personal injury or death.

CAUTION - Hazards or unsafe practices which COULD

result in minor personal injury.

Do not add gasoline, dry-cleaning solvents, or other

flammable or explosive substances to the wash

water. These substances give off vapors that could

ignite or explode.

Do not wash articles which have been previously

cleaned, washed, soaked, or spotted with gasoline,

dry-cleaning solvents, oil, waxes, chemical solvents,

alcohol, turpentine, or other flammable or explosive

materials. These substances will be retained in

articles, and articles which still contain these

flammable or explosive substances give off vapors

that could ignite or explode.

Observe these precautions when using cleaning

fluids, spot or stain removers, etc. These products

should be labeled "nonflammable;' Use according to

manufacturers directions in a well ventilated area or

outdoors. Thoroughly rinse articles by hand before

placing them in the washer. Some of these products

- rust removers for example - will damage

components and the finish of the washer.

Keep area around and underneath washer free from

the accumulation of combustible materials, such as

lint, paper, rags, gasoline, and all other flammable

vapors and liquids.

HYDROGEN GAS IS EXPLOSIVE! Under certain

conditions, hydrogen gas may be produced in a hot

water system that has not been used for two weeks

or more. If the hot water system has not been used

for such a period, before using the washer, turn on

all the hot water faucets and let the water flow from

each faucet for several minutes. This will release any

accumulated hydrogen gas. As this gas is

flammable, do not smoke or use an open flame

during this time.

Recent studies have shown that if vegetable oil

contaminated materials are incompletely washed, a

carry-over and buildup of the oil may contribute to a

chemical reaction (spontaneous combustion) that

could cause a load to catch fire by itself. This would

be more likely to happen if the load were left in the

dryer after tumbling stopped or if items were folded

and stacked while warm.

ImportnntSnfet¥Instructions

1. Read all instructions before using the appliance.

2. As with any equipment using electricity and having

moving parts, there are potential hazards. To use this 7.

appliance safely, the operator should become familiar

with the instructions for operation of the appliance 8.

and always exercise care when using it.

3. De net install or store this appliance where it will be

exposed to the weather.

4. Install and level washer on a floor that can support

the weight.

5. This appliance must be properly grounded. Never

plug the appliance cord into a receptacle which is

not grounded adequately and in accordance with

local and national codes. See installation instructions

for grounding this appliance.

6. To avoid the possibility of fire or explosion:

a. De net wash items that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoline, dry-cleaning solvents, other flammable or

explosive substances as they give off vapors that

could ignite or explode. Hand wash and line dry

any items containing these substances.

Any material on which you have used a cleaning

solvent, or which is saturated with flammable

liquids or solids, should not be placed in the

washer until all traces of these liquids or solids

and their fumes have been removed.

These items include acetone, denatured alcohol,

gasoline, kerosene, some liquid household

cleaners, some spot removers, turpentine, waxes

and wax removers.

De not add gasoline, dry-cleaning solvents, or

other flammable or explosive substances to the

wash water. These substances give off vapors that

could ignite or explode.

Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been

used for two weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been

used for such a period, before using a washing

machine or combination washer-dryer, turn on all

hot water faucets and let the water flow from each

for several minutes. This will release any

10.

11.

12.

13.

14.

15.

16.

17.

18.

19.

accumulated hydrogen gas. As the gas is

flammable, de net smoke or use an open flame

during this time.

d. De net wash or dry items that are soiled with

vegetable or cooking oil. These items may contain

some oil after laundering. Due to the remaining oil,

the fabric may smoke or catch fire by itself.

Do not reach into the appliance if the tub or agitator

is moving.

De net allow children or pets to play on, in, or in

front of the appliance. Close supervision is necessary

when the appliance is used near children and pets.

Do not tamper with controls.

De net repair or replace any part of the appliance or

attempt any servicing unless specifically

recommended in published user-repair instructions

that you understand and have the skills to carry out.

Unplug power supply cord before attempting to

service your washer. Service is to be done only by

qualified service personnel.

The agitator should not be removed. If the agitator is

removed, it must be replaced by pushing down

completely and the locking screw tightened before

the washer is operated.

Keep all laundry aids such as detergents, bleach, etc.,

out of the reach of children, preferably in a locked

cabinet. Use laundry aids only as directed by the

manufacturer. Observe all warnings on container labels.

Keep the area around and underneath washer free

from the accumulation of combustible materials, such

as lint, paper, rags, gasoline, and all other flammable

vapors and liquids.

De not use chlorine bleach and ammonia or acids

(such as vinegar or rust remover) in the same wash.

Hazardous fumes can form.

De net machine wash fiberglass materials. Small

particles can stick to fabrics washed in following

loads and cause skin irritation.

For flame resistant finishes - follow garment

manufacturer's instructions carefully. Improper

laundering could remove the finish.

Before the appliance is removed from service or

discarded, remove the door to the washing compartment.

Inlet hoses are subject to damage and deterioration

over time. Check the hoses periodically for bulges, kinks,

cuts, wear or leaks and replace them every five years.

SAVE THESE iNSTRUCTiONS

UsingtheControls-2SpeedComboModels

Select Load Size

Determine the selected setting based on clothes load

size. Selection should provide sufficient water to permit

clothes to circulate freely during agitation.

It may become necessary, due to bulky fabrics, to

adjust the water level after agitation begins. To adjust

the water level, turn the control to Reset and then

back to the desired setting.

Mini 1/4 Full

Med 1/4 - 3/4

Super 3/4- Full

Note: Items must circulate freely for best results.

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold

water for washing and cold water for rinsing. Use the

chart below as a guide.

White and heavily soiled, color-fast

Hot/Cold

items.

Warm/Cold Moderately soiled, colored items;

most wrinkle-free items.

Cold/Cold Brightly colored, lightly soiled

items; washable woolens.

Note: In wash water temperatures below 60° F,

detergents do not dissolve well or clean well. Care

labels define cold water as up to 85° E

Select Cycle

To select a cycle, push the control dial in (off position)

and turn it to the right (clockwise) until the pointer is at

the number of minutes needed for the wash load in the

Cottons, Wrinkle-Free Fabrics or Delicates cycles.

Cottons Cycle

Provides normal agitation and normal spin speeds to

wash cottons and heavily soiled items. For maximum

cleaning, set the dial at 14 minutes.

Wrinkle-Free Fabrics Cycle

Provides normal agitation and normal spin speed with

a spray rinse to protect wrinkle-free fabrics.

Delicates Cycle

Provides slow agitation speed and slow spin speed for

delicates and knits.

Pull Control Dial Out to Start

You may stop the washer at any time by simply

pushing the control dial in. Therefore it is possible to

obtain a non-agitated soak or to shorten, skip or

repeat any part of a cycle. The control dial must be

)ushed in (off position) when you change the setting.

Note: Do not attempt to turn the control dial

counterclockwise. Damage to the timer will result.

UsingtheControls-4SpeedComboModels

_rmtd

47C ATC

ATc )

U)AD SIZE _SH_ _Ph SP_;ED

1*'_4.SH/RINSE TF,MP

Select Load Size

Determine the selected setting based on clothes load

size. Selection should provide sufficient water to permit

clothes to circulate freely during agitation.

It may become necessary, due to bulky fabrics, to

adjust the water level after agitation begins. To adjust

the water level, turn the control to Reset and then

back to the desired setting.

Mini 1//4 Full

Small 1//4- 1/2

Medium 1/2 - 3//4

Super 3//4- Full

Note: Items must circulate for best results.

freely

Select Wash/Spin Speed

Your washer has selectable wash and spin speed

combinations.

Normal/Normal

Normal/Slow

Slow/Normal

Slow/Slow

Sturdy fabrics needing maximum

water extraction.

Sturdy fabrics needing a slower

spin speed because of wrinkling.

Heavy loads of delicate fabrics

needing a fast spin for better water

extraction.

Delicate fabrics needing slower

wash and spin speed because of

clothing construction.

Select Wash/Rinse Temperature

Your washer gives you a choice of hot, warm or cold

water for washing and cold water for rinsing. Use the

following chart as a guide.

i/ _ii ¸ii/iiiiiiiiH!ii!iii!tii_i_i_i _i!_i !illi_i_i_i_i_i_i_i_I

r_leS.

Cold/Cold Brightly colored, lightly soiled items,

washable woolens.

These settings feature Automatic Temperature Control:

Saves energy by adding cold water

ATC Hot/Cold, to the hot water from your water

ATC Warm/Cold heater. Provides optimum cleaning

at lower temperatures.

May add hot water to the incoming

cold water as the washer fills. This

ATC Cold/Cold

assures that the water will be warm

enough to properly activate detergent.

Control features vary by model

_X7'_4 _Ii S&_

DH.tCAT_;.S

Note: In wash water temperatures below 60° F,

detergents do not dissolve well or clean well. Care

labels define cold water as up to 85° F.

Select Options {if desired)

Extra Rinse

When the knob is in the on position, an additional

rinse at the end of the Cottons cycle is provided to

more completely remove laundry additives, suds,

perfumes, etc.

Select Cycle

Delicates Cycle

This cycle provides up to 12 minutes of agitation.

Depending on the load, select either the Slow/Slow or

Slow/Normal wash/spin speed.

Soak Cycle

This cycle provides approximately 30 minutes of

agitation and soaking to help remove stubborn dirt

and stains. For more information see page 7.

Pull Control Dial Out to Start

To select a cycle, push the control dial in (off position)

and turn it to the right (clockwise) until the pointer is at

the number of minutes desired for the wash load.

IMPORTANT: For optimum fabric care, the

appropriate wash and spin speed for the load type

must be selected using the Wash/Spin Speed knob.

Cottons Cycle

For regular fabrics, select the cycle time and turn the

Wash/Spin Speed dial to Normal/Normal.

You may stop the washer at any time by simply

pushing the control dial in. Therefore it is possible to

obtain a non-agitated soak or to shorten, skip or

repeat any part of a cycle. The control dial must be

pushed in (off position) when you change the setting.

I Note: Do not attempt to turn the control dialcounterclockwise. Damage to the timer will result.

For fabrics needing a slower spin speed to reduce

wrinkling, set the control dial on Wrinkle-Free and turn

the wash/spin speed dial to Normal/Slow.

SpeciolFeotures

Liquid Bleach Dispenser

The dispenser automatically dilutes liquid chlorine

bleach before it reaches your wash load.

To use, follow these steps:

1. Measure liquid chlorine bleach carefully, following

the instructions on the bottle.

2. Pour liquid chlorine bleach into bleach

dispenser before adding the load. Avoid splashing

or over-filling the dispenser.

Notes:

Never pour undiluted liquid chlorine bleach

directly onto the load or into the wash tub. It is a

powerful chemical and can cause fabric damage,

such as tearing or color loss, if not used properly.

If you prefer to use color-safe, non-chlorine

bleach, pour it into the wash tub with your

detergent. Do not pour non-chlorine bleaches into

the bleach dispenser.

Liquid Dispenser

The dispenser may be used for fabric softener with

most cycles or liquid detergent with the Soak cycle

(select models). The liquid dispenser should be

cleaned before and after each use of liquid detergent.

The dispenser automatically releases the liquid at the

proper time during the cycle.

To use, follow these steps:

1. Pour a measured amount of desired liquid into

the dispenser to fill line only.

2. If liquid comes below line, add warm water.

If it is necessary to clean the dispenser:

1. Pull the dispenser off of the top of the agitator.

2. Soak for one hour in sink or container in hot water

and dishwashing liquid.

3. Hold hands over top and bottom of dispenser and

shake to loosen buildup.

4. Rinse with clean, hot water.

5. Repeat process if necessary.

6. Replace dispenser on agitator.

Do not use dishwashing liquid inside

the washer. Oversudsing can occur.

Soak Cycle (select models)

_ :4_ ....

This cycle eliminates the inconvenience of soaking

stained loads before they are placed in the washer. To

use:

1. Add liquid or granular detergent to the washtub.

2. Add the load.

3. Add liquid detergent only to the Liquid Dispenser

in the top of the agitator.

/4. Set the control dial to Start in the Soak Cycle.

The load will soak for 30 minutes with brief periods of

agitation. The water is then spun out and clean wash

water is added along with the liquid detergent for a

16-minute wash cycle.

Safety Spin

If for any reason you open the washer lid when the

washer is in a spin or extract period, the operation will

immediately stop. This is for your personal safety. If

your washer does not stop, call your service technician

immediately. When the lid is closed, the operation will

automatically resume.

SpecialFeatures

Automatic Lint Filtering System

The Lint Filtering System does not require

cleaning.

Wash and rinse water is filtered and re-filtered

continuously to trap lint shed by most fabrics during

the agitation cycle before it can be redeposited on the

wash load. The engineered hole design on the wash

basket, in conjunction with water flow produced by the

agitator, traps lint away from the clothes between the

inner wash basket and the outer tub. Lint is

automatically flushed from the washer during the spin

cycle.

Unbalanced Spin Load

Compensator

Your new washer is designed to handle out-of-balance

loads without shutting down or interrupting the

washing cycle.

For this reason, the cycle will always be completed. If

heavier fabrics in such out-of-balance loads should

ever contain excessive moisture at the completion of

the cycle, redistribute the clothes in the washer and

reset the control dial for the final spin period.

Overload Protector

A built-in protector automatically shuts off the washer

motor in case of an overload. This can occur if:

• The load being washed is too heavy.

• Too many appliances are plugged into the line

operating your washer.

• A low voltage condition exists on the line.

• Lid is opened and closed repeatedly.

The overload protector permits the washer to start again

when the motor has cooled to a safe operating temperature.

If the motor stops repeatedly, call your service technician.

Care& Cleaning

1. After washing, leave the lid open until the interior

is dry.

2. Check hoses to be sure there are no kinks or knots.

3. Your washer should not be installed where

temperatures will go below freezing, as damage to

the washer could result.

4. To clean, occasionally wipe exterior with a clean

damp sponge or cloth. De not use polish on

plastic parts.

5. Lifetime lubrication is done at the factory, so your

washer never needs to be oiled or greased.

6. Do not lay heavy or sharp objects on top of your

washer.

7. The top of the washer should not be used for

removing stains from garments. Some stain

removers, such as rust remover, will mar the finish.

11. If you close your home for the winter, have a service

technician drain the washer. Unplug cord from

electrical outlet and disconnect hoses from faucets.

Cleaning the Interior

Clean the interior of the washer periodically to remove

any dirt, soil, odor, mold, mildew or bacteria residue

that may remain in the washer as a result of washing

clothes. We recommend taking the following steps

every 60 to 120 days to clean and freshen your washer

interior. The frequency with which the washer should

be cleaned and freshened depends on factors such as

usage, the amount of dirt, soil or bacteria being run

through your washer, or the use of cold water. Failure

to follow these instructions may result in unsatisfactory

conditions, including unpleasant odor and/or

permanent stains on the washer or washload.

To clean and freshen the washer interior:

8. Remove pins, buckles or other sharp objects from

clothes to prevent scratching interior parts.

9. Clothes should not be stored in washer.

10.

Bleach, detergent, solvents, etc. spilled on the top

of your washer that are allowed to remain will

remove the glossy finish. Remove all spills with a

damp, soft cloth.

1. Add a measured amount of chlorine bleach to the

bleach dispenser, following package directions.

2. Add 1/4 cup of detergent to the tub.

3. Run the washer without a load through a complete

cycle using hot water.

4. Repeat the process if necessary.

OpermingTips

Detergent

• Use either liquid or granular laundry detergent. For

best results, be sure detergent is added to the

washer BEFORE the load and be sure the wash

water is above 60 ° F.

• Use the correct amount of detergent for the load size,

soil level and water conditions. Use more detergent if

you have hard water and very soiled loads.

If you have soft water or a lightly soiled load, use less

detergent. (See manufacturer's instructions.)

• Wipe up any detergent spills on the washer.

• For best results add the detergent to the washtub

before adding the load.

• Put dry, unfolded clothes loosely in the tub, up to the

top row of holes for a maximum load.

• Do not wrap large items like sheets around the

agitator.

• Mix large and small items for best circulation. Wash

bulky items like blankets separately.

• When laundering wrinkle-free items or items of

delicate construction, washable woolens or loosely

knit items, never use less than the MEDIUM water

level setting. This will minimize shrinkage, wrinkling

and pulling of seams.

• Close lid carefully to avoid slamming.

Additional Tips

• During the spin, it is possible for the load to become

unevenly distributed in the tub. If this happens, push

in the control dial, open the lid, redistribute the load,

close the lid and restart the washer. The spin will

resume at the point it was interrupted.

• The washer will pause briefly throughout each cycle.

These pauses are normal.

• This washer is designed so that it will not agitate or

spin when the lid is open. It will, however, fill with the

lid open so water is available for pretreating stains or

diluting fabric softener.

• If you open the lid during a spin cycle, the washer

will stop. When the lid is closed and the washer is

restarted, the washer will continue the cycle at the

point it was interrupted.

Troubleshooting

Won't Fill

Won't Agitate

Won't Spin

or Drain

Load is Wet

Stops

Leaks Water

Is Noisy

Fills with

the Wrong

Temperature

Water

• Plug cord into live electrical outlet.

• Check fuse or reset circuit breaker.

• Turn the control dial to proper cycle and restart the washer.

• Turn both faucets on fully.

• Straighten inlet hoses.

• Disconnect hoses and clean screens. Hose filter screens may be plugged.

• Check fuse or reset circuit breaker.

• Make sure the lid is completely closed.

• Turn the control dial to proper cycle and restart the washer.

• Pauses are normal. Wait and see if the washer will start again.

• Check fuse or reset circuit breaker.

• Straighten drain hoses. Eliminate kinked hoses. If there is a home drain restriction, call for

drain service.

• Close lid and restart the washer. Foryour safety, washer will not spin unless the lid is closed.

• Suds lock - caused by too much suds. Rewash without detergent. Use correct amount of a

low-sudsing detergent.

• Unevenly distributed load. Redistribute the load, close the lid and restart the washer. Check for

leveling. Be sure water level is acceptable for load size.

• A normal spin speed is recommended for heavy loads like jeans or towels.

• Plug cord into live electrical outlet.

• Check fuse or reset circuit breaker.

• Close lid and restart the washer. Foryour safety, washer will not agitate or spin unless lid is closed.

• This may be a pause in the cycle. Wait briefly and it may start.

• Make sure hose connections are tight.

• Make sure end of drain hose is correctly inserted and secured to drain facility.

• Avoid extended soaking - soak for 30 minutes or less.

• Avoid overloading.

• Be sure washer is leveled properly as outlined in installation manual.

• Weak floors can cause vibration and walking.

• Operating sounds will vary depending on agitation speed.

• Turn both faucets on fully.

• If equipped with a temperature selector dial, be sure it is set directly on a temperature setting and

not between settings.

• Make sure temperature selection is correct.

• While the washer is filling, you may notice just hot and/or just cold water entering the tub when

cold or warm wash temperatures are selected. This is a normal function of the Automatic

Temperature Control (:select models) feature as the washer determines the temperature of

the water.

Cycle Selector • Extra Rinse (:select models) is selected.

Advances Through

Off

• If Auto Temperature Control (:selectmodels) is selected, cold water may feel warmer than cold

water from the tap.

• Make sure hoses are connected to correct faucets and inlet connections. Be sure water supply is

regulated correctly. Flush water line before filling washer.

• Check the water heater. It should be set to deliver a minimum 120° F(::49° C) hot water at the tap.

Also check water heater capacity and recovery rate.

Disconnect hoses and clean screens. Hose filter screens may be plugged.

Service& Norront¥

Warranty

Limited One Year Warranty -

Parts and Labor

Forone (:1)year from the original retail

purchase date, any part which fails in

normal home usewill be repaired or

replaced free of charge.

Canadian Residents

Theabovewarranties only cover an

appliance installed in Canadathat has

been certified or listed by appropriate test

agencies for a compliance to a National

Standard of Canadaunless the appliance

was brought into Canadadue to transfer

of residence from the United Statesto

Canada.

The specific wanantles expressed above are

the ONLY warranties provided by the

manufacturer: These wananties give you

specific legal rights, and you may also have

other rights which vat]/from state to state.

CUSTOMER'S SOLE AND EXCLUSIVE

REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. IMPLIED

WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR

A PARTICULAR PURPOSE,ARE LIMITED

TO ONE YEAR ORTHE SHORTEST

PERIOD ALLOWED BY LAW. MAYTAG

CORPORATION SHALL NOT BE LIABLE

FOR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. SOME STATESAND

PROVINCES DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL

DAMAGES, OR LIMITATIONS ON THE

DURATION OF IMPLIED WARRANTIES OF

M ERCHANTABILITYOR FITNESS,SO

THESE EXCLUSIONS OR LIMITATIONS

MAY NOT APPLY TOYOU. THIS

WARRANTY GIVESYOU SPECIFICLEGAL

RIGHTS AND YOU MAY ALSO HAVE

OTHER RIGHTS,WHICH VARY STATETO

STATEOR PROVINCE TO PROVINCE.

What is Not Covered By These Warranties

1. Condit,ons and damages resulting from any of the following:

a. Improper mstallat,on, delivery, or maintenance.

b. Any repmr, modificat,on, alterat,on, or adjustment not authorized by the

manufacturer or an authorized serv,cer.

c. MBuse, abuse, acadents, unreasonable use, or acts of God.

d. Incorrect electric current, voltage, electrical and/or gas supply.

e. Improper setting of any control.

2. Warrant,es are vo,d ,f the original serial numbers have been removed, altered,

or cannot be readily determined.

3. Dght bulbs, water filters and a,r filters.

4. Products purchased for commercml or industrial use.

5. The cost of serv,ce or serv,ce call to:

a. Correct mstallat,on errors. For products requinng vent,lat,on, rigid metal

ductmg must be used.

b. Instruct the user on the proper use of the product.

c. Transport the appliance to and from the serv,cer.

6. Any food loss due to refrigerator or freezer product fmlures.

7. Expenses for travel and transportat,on for product serv,ce m remote Iocat,ons.

8. Outs,de of the Umted States and Canada th,s warranty does not apply.

Contact your dealer to determine ,f another warranty applies.

Consequentml or madental damages sustained by any person as a result of

any breach of these warrant, es. Some states do not allow the exclumon or

lira,tat,on of consequentml or madental damages, so the above exclumon may

not apply.

If You Need Service

F,rst see the Troubleshoot,ng sect,on m your Use and Care Guide or call the

dealer from whom your appliance was purchased or call Maytag Serv,ces, LLC,

Customer AssBtance at 1-800-688-9900 USA and 1-800-688-2002 Canadato

locate an authorized serv,cer.

Be sure to reta,n proof of purchase to verifywarranty status. Refer to WARRANTY

for further ,nformat,on on owner's respons,bdit,esfor warranty serv,ce.

If the dealer or serv,ce company cannot resolve the problem, write to Maytag

Serv,ces,LLC, Attn: CAIR_Center, RO. Box 2370,Cleveland,TN 37320-2370,or call

1-800-688-9900 USA and 1-800-688-2002 Canada. U.S.customers using

TTY for deaf, heanng mlpmred or speech mlpmred, call 1-800-688-2080.

User's guides, serv,ce manuals and parts ,nformat,on are avadablefrom Maytag

Serv,ces,LLC, Customer Ass,stance.

Notes: When wnt,ng or calling about a serv,ce problem, please ,nclude:

a. Your name, address and telephone number;

b. Model number and serial number;

c. Name and address of your dealer or serv,cer;

d. A clear descnpt, on of the problem you are hav,ng;

e. Proof of purchase (sales rece,pt).

uSe

AAV-2

AdmiralFJl

Table des mati_tes

Importantes consignes

de s_curit_ ............ 13-14

Fonctionnement ........... 22

Utilisation des commandes -

ModUle h combinaison

deux vitesses ........... 15-16

ModUles _ combinaison

quatre vitesses .......... 17-18

Caractbristiques

spbciales .............. 19-20

Nettoyage et entretien ..... 21

Recherche des pannes ..... 23

Garantie et service

aprbs-vente ............... 25

Guia de uso y cuidado ..... 26

Importuntesconsignesdesecurit6

Installateur : Veuillez laisser le present guide avec

I'appareil.

Client : Veuillez lire le present guide et le conserver pour

reference future. Conservez aussi les re£us de caisse et

les cheques obliteres 9 titre de preuve d'achat.

Numero de modele

Numero de serie

Date d'achat

Pour toute question, contacter :

Service 9 la clientele

1-800-688-2002 Canada

(lundi au vendredi, 8 h _ 20 h, heure de I'est)

Site Internet: http://www.maytag.com

En raison de nos efforts constants d'amelioration de la

qualite de nos appareils electro-menagers, il se peut

qu'une laveuse soit modifiee sans que le guide soit revise.

Pour le service aprbs-vente, voir page 25.

Ce qu'il faut savoir propos

des consignes de s curit6

Les constgnes de securtte et les raises en garde presentees

dans ce guide ne couvrent pas toutes les s.tuat.ons

poss.bles. Fa.re preuve de ]ugement, de prudence et

d'attentton Iors de I'.nstallatton, de I'entretten et de

I'ut.lisat.on de I'appare.I.

Lorsque survtent un probleme ou une situation mhabttuelle,

toujours commun.quer avec le fabncant.

Reconnaissez les tiquettes, phrases

ou symboles sur la securite

AVERTISSEMENT - Risques ou pratiques non sores, qui

POURRAIENT resulter en de graves blessures ou meme

la mort.

Ne pas ajouter d'essence, de solvants de nettoyage 9 sec

ou toute autre substance inflammable ou explosive

I'eau de lavage. Ces substances produisent des vapeurs

qui pourraient s'enflammer ou exploser.

Ne pas laver d'articles qui ont auparavant ete nettoyes,

laves,trempes ou detaches 9 I'aide d'essence, de solvants

de nettoyage _ sec, d'huiles, de cires, de solvants

chimiques, d'alcool, de terebenthine ou d'autres produits

explosifs ou inflammables. Ces substances resteront

incrustees dans les articles, et ceux-ci produisent des

vapeurs qui peuvent s'enflammer ou exploser.

Suivre ces precautions Iorsde I'utilisation de produits

nettoyants liquides, de detachants, etc. Ces produits

doivent porter la mention ininflammable. Utiliser

conformement aux directives du fabricant dans un

endroit bien acre ou _ I'exterieur. Rincer _ fond les

articles 9 la main avant de les mettre dans la laveuse.

Certains produits - ceux qui enlevent la rouille par

exemple - peuvent endommager les pieces et la finition

de la laveuse.

I_vitertoute accumulation de materiaux combustibles, tels

que la charpie, le papier, les chiffons, I'essence et autres

vapeurs et liquides inflammables, sous la laveuse et

autour de celle-ci.

L'HYDROGi:NE ESTUN GAZ EXPLOSIF ! Dans

certaines conditions, il peut y avoir production

d'hydrogene dans un systeme de chauffage d'eau qui

n'est pas utilise pendant 2 semaines ou davantage. Si le

systeme de chauffage d'eau n'a pas ere utilise pendant

une telle duree, ouvrir tousles robinets d'eau chaude et

laisser couler I'eau pendant plusieurs minutes avant

d'utiliser la laveuse. Ceci elimine toute accumulation

d'hydrogene. Ce gaz etant inflammable, ne pas ruiner ni

utiliser de flamme vive pendant cette procedure.

Des etudes recentes ont demontre que si les substances

contaminees d'huile vegetale ne sont pas completement

nettoyees, une accumulation d'huile peut provoquer une

reaction chimique (combustion spontanee) qui pourrait

causer un incendie. Cela risque davantage de survenir

Iorsque les vetements sont laisses dans la secheuse

apres que le tambour air cesse de tourner ou que les

articles sont plies et empiles avant que la chaleur ne se

soit dissipee.

ATTENTION - Risques ou pratiques non sores qui

POURRAIENT resulter en blessures mineures.

Importnntesconsidnesdesecurite

1. Lire toutes les instructions avant d'utiliser la laveuse.

2. Comme avec tout equipement fonctionnant _ I'electricite

et comportant des pieces mobiles, il existe toujours des

possibilites de danger. Pour utiliser cette machine dans

les meilleures conditions de securite, I'operateur doit se

familiariser avec les instructions de fonctionnement de

I'appareil et user de prudence pendant son utilisation.

3. Ne pas installer ni remiser la laveuse dans un endroit

oQ elle est exposee aux intemperies.

4. Installer la laveuse et la mettre de niveau sur un

plancher pouvant supporter son poids.

5. Cet appareil doit etre correctement mis 9 la terre. Ne

jamais brancher le cable electrique d'une laveuse sur

une prise murale non mise _ la terre conformement aux

codes Iocaux et nationaux. Voir les instructions

d'installation pour la mise 9 la terre de cette machine.

6. Pour eviter les risques d'incendie ou d'explosion :

a. Ne pas laver d'articles qui ont auparavant ete

nettoyes ou laves _ I'aide d'essence, de solvants de

nettoyage 9 sec ou d'autres produits explosifs ou

inflammables, ou qui en sont imbibes ou eclabousses,

car ces substances produisent des vapeurs qui

peuvent s'enflammer ou exploser. Laver 9 la main et

secher 9 I'air tout article contenant ces substances.

Tout tissu sur lequel des solvants de nettoyage ont

ete utilises ou qui est sature de liquides ou solides

inflammables ne doit pas etre mis dans la laveuse

avant que toute trace et toute vapeur de ces liquides

ou solides ne soient completement eliminees.

Ces produits comprennent I'acetone, I'alcool

denature, I'essence, le kerosene, certains produits de

nettoyage menagers, les detachants, la terebenthine,

les cires et les decapants de cire.

Ne pas ajouter d'essence, de solvants de nettoyage

sec ou toute autre substance inflammable ou

explosive 9 I'eau de lavage. Ces substances produisent

des vapeurs qui pourraient s'enflammer ou exploser.

Dans certaines conditions, il peut y avoir production

d'hydrogene dans un systeme de chauffage d'eau qui

n'est pas utilise pendant 2 semaines ou plus.

L'HYDROGI_NEESTUN GAZ EXPLOSIF.Si le systeme

de chauffage d'eau n'est pas utilise sur une telle

duree, ouvrir tousles robinets d'eau chaude et laisser

couler I'eau pendant plusieurs minutes avant d'utiliser

la laveuse ou la ensemble laveuse-secheuse. Ceci

elimine toute accumulation d'hydrogene. Ce gaz etant

inflammable, ne pas fumer ni utiliser de flamme vive

pendant cette procedure.

d. Ne pas laver ou secher d'articles taches d'huile

vegetale ou de cuisson. Ces articles pourraient etre

encore impregnes d'huile apres la lessive. Pour cette

raison, le tissu pourrait emettre des fumees ou

prendre feu de lui-meme.

Ne pas mettre la main ou le bras dans la laveuse si

I'agitateur ou cuve est en mouvement.

Ne pas permettre aux enfants ou aux animaux familiers

de jouer sur I'appareil, _ I'interieur ou en face de celui-

ci. Une supervision etroite est necessaire Iorsque

I'appareil est utilise _ proximite d'enfants ou d'animaux

familiers.

9. Ne pas modifier les mecanismes de commande.

10. Ne pas reparer ou remplacer une piece de la laveuse

ou proceder 9 un depannage, sauf si les instructions

publiees le recommandent et que la personne effectuant

la reparation les comprend et possede les

connaissances voulues pour les executer.

11. Debrancher le cordon d'alimentation electrique avant

d'essayer de reparer la laveuse. Les reparations ne

doivent etre effectuees que par du personnel qualifie.

12. L'agitateur ne doit pas eve retire. S'il est retire, le

replacer en I'enfon(_ant 9 fond, puis serrer la vis de

blocage avant de faire fonctionner la laveuse.

13. Conserver tousles produits de lessive, les detergents,

les produits de blanchiment, etc., hors de portee des

enfants, et de preference dans une armoire fermee

cle. N'utiliser ces produits que selon les directives du

fabricant. Observer tousles avertissements paraissant

sur les etiquettes des differents produits.

14. S'assurer que toute la zone autour de la laveuse et en

dessous, soit degagee de toute accumulation de

materiaux combustibles comme charpie, papier, chiffons,

essence et tout autre liquide ou vapeur inflammable.

15. Ne pas melanger de javellisant et d'ammoniaque ou

d'acides (tels que du vinaigre ou du produit pour enlever

la rouille) pour une meme charge de linge. Des vapeurs

nocives peuvent se former.

16. Ne pas laver d'articles en fibre de verre _ la laveuse. De

petites particules peuvent se coller sur le linge lave par

la suite et provoquer des irritations cutanees.

17. Apprets resistants aux flammes - suivre attentivement

les instructions du fabricant du vetement. Un vetement

incorrectement lave ou seche pourrait perdre son appret

ignifuge.

18. Avant de mettre la laveuse hors service ou au rebut,

retirer la porte du compartiment de lavage.

19. Les tuyaux d'alimentation se deteriorent progressivement.

Inspecter les tuyaux _ intervalle regulier; rechercher

dilatations, ecrasements, coupures, fuites et indices

d'usure. Remplacer les tuyaux apres 5 ans de service.

CONSERVER CES INSTRUCTIONS 14

Utilisutiondescommundes

Modelesocombinuisonodeuxvitesses

S_lectionnez le volume de

la charge

Determinez le reglage approprie selon le volume du linge

laver. Le reglage choisi doit fournir assez d'eau pour que le

linge circule librement pendant le brassage.

II peut s'averer necessaire d'ajuster le niveau de I'eau pour

les articles volumineux, une fois le brassage commence.

Pour ce faire, tournez le bouton sur Reset (reinitialisation),

puis sur le reglage desire.

Mini (mini) 1/4 plein

Med (moyen) 1/4 - 3/4

Super (super) 3/4 - plein

Remarque : Pour de meilleurs resultats, les

articles doivent pouvoir circuler librement.

S_lectionnez la temperature de

I'eau de lavage/rin_age

Votre laveuse vous permet de choisir entre de I'eau chaude,

tiede ou froide pour le lavage et fournit de I'eau froide pour

le ringage. Utilisez le tableau ci-dessous comme guide •

Hot/Cold

(chaude/froide)

Blancs et articles couleurs grand

teint, tres sales.

Articles de couleur, moderement

Warm/Cold

(tiede/froide) sales; majorite des articles

infroissables.

Cold/Cold Articles de couleurs vives, legerement

(froide/froide) sales; laine lavable _ la machine.

Remarque: Lorsquela temperature de I'eau de

lavage est inferieure 9 60 °F (15,5 °C), les detergents se

dissolvent mal ou perdent de leur efficacite. D'apres les

etiquettes d'entretien des tissus, I'eau est consideree

comme froide jusqu'_ 85°F (29 °C).

SClectionnez le cycle

Pour choisir un cycle, appuyez sur le bouton de commande

(position arret) et tournez-le vers la droite (sens horaire)

jusqu'9 ce que I'aiguille soit sur le nombre de minutes

nCcessaires selon la charge de linge, dans les cycles

Cottons (coton), Wrinkle-Free Fabrics (tissus infroissables)

ou Delicates (linge dClicat).

Cottons Cycle ([cycle coton)

Fournit une vitesse de brassage et de rimTage normale pour

laver les cotons et les articles tres sales. Pour un lavage

optimal, rCglez sur 14 minutes.

Wrinkle-Free Fabrics Cycle

([cycle tissus infroissables)

Fournit une vitesse de brassage et d'essorage normale avec

un rin?age par projection pour protCger les tissus

infroissables.

Delicates Cycle ([cycle linge delicat)

Fournit une vitesse de brassage et d'essorage lente pour le

linge dClicat et la laine.

Trez le bouton de commande

pour demarrer

Vous pouvez arr0ter la laveuse _ tout moment en appuyant

tout simplement sur le bouton de commande. II est ainsi

possible d'obtenir un trempage sans brassage ou de

raccourcir, passer ou rCpCtertoute partie du cycle de lavage.

Le bouton de commande doit etre eafoace (position arret)

Iorsque vous effectuez des modifications.

Remarque: N'essayez pas de tourner le bouton de

commande dans le sens antihoraire. Cela endommagerait

la minuterie.

Utilisotiondescommundes

Modelescombinaisonquatrevitesses

Selectionnez le volume de

la charge

Determinez le reglage approprie selon le volume du linge fl

laver. Le reglage choisi doit fournir assez d'eau pour que le

linge circule librement pendant le brassage.

II peut s'averer necessaire d'ajuster le niveau de I'eau pour

les articles volumineux, une fois le brassage commence.

Pour ce faire, tournez le bouton sur Reset (reinitialisation),

puis sur le reglage desire.

Mini (mini) 1/4 plein

Small (petit) 1/4 - 1/2

Medium (moyen) 1/2 - 3/4

Super (super) 3/4 - plein

I,omar,,o•+ur0omoi..oursr+su.,+..osI

articles doivent pouvoir circuler librement.

Selectionez la vitesse de lavage

et d'essorage

Votre laveuse possede diverses combinaisons de vitesses de

lavage et d'essorage.

Normal/Normal

(normale/normale)

Normal/Slow

(normale/lente)

Slow/Normal

(lente/normale)

Slow/Slow

(lente/lente)

Tissus robustes necessitant une

extraction maximale de I'eau.

Tissus robustes necessitant une

vitesse d'essorage plus lente pour ne

3as etre froisses.

Charges Iourdes de tissus delicats

necessitant un essorage rapide pour

une meilleure extraction de I'eau.

Tissus delicats necessitant une

vitesse de lavage et d'essorage plus

lente en raison du type de tissu.

Selectionnez la temperature de

I'eau de lavage/rin£age

Votre laveuse vous permet de choisir entre de I'eau chaude,

tiede ou froide pour le lavage et fournit de I'eau froide pour

le ringage. Utilisez I'information suivante comme guide.

ATC Hot/Cold

(ACT Chaude/Froide)

ATC Warm/Cold

(ACT Ti_de/Froide)

ATC Cold/Cold

(ACT Froide/Froide)

Cold/Cold Articles de couleurs vives, legerement

(Froide/Froide) sales; laine lavable _ la machine.

Cesr_QlaQesutilisentlacommandeautomatiquedetemp_ratur_

I_conomise I'energie en ajoutant de

I'eau froide 9 I'eau chaude provenant

de votre chauffe-eau. Permet un lavage

optimal _ basse temperature.

Peut ajouter de I'eau chaude 9 I'eau

froide Iors du remplissage de la

laveuse.Ainsi, I'eau est assez chaude

pour que le detergent soit efficace.

Lesdispositifs de commande changent par le module

Remarque: Lorsque la temperature de I'eau de

lavage est inf(_rieure fl 60 °F (15,5 °C), les detergents se

dissolvent mal ou perdent de leur efficacit& D'apres les

etiquettes d'entretien des tissus, I'eau est consid(_r(_e

comme froide jusqu'_ 85 °F (29 °C).

Pour les tissus necessitant une vitesse de rim;age plus lente

afin de reduire le nombre de faux plis, reglez le bouton de

commande sur Wrinkle-Free (antifroissement) et le bouton

de vitesse de lavage/essorage sur Normal/Slow

(normale/lente).

Delicates Cycle (cycle linge delicat)

Selectionnez de options

(si vous le desirez)

Extra Rinse (Rin£age supplementaire)

Lorsque le bouton est sur la position Marche (on), un

rim;age supplementaire est fourni fl la fin du cycle Coton

pour bien eliminer les additifs de lavage, la mousse, les

parfums, etc.

Ce cycle compte jusqu'9 12 minutes de brassage. Selon la

charge, selectionnez la vitesse de lavage/essorage

lente/lente (Slow/Slow) ou lente/normale (Slow/Normal).

Soak (cycle trempage)

Ce cycle fournit environ 30 minutes de brassage et de

trempage pour retirer la salete incrustee et les taches

tenaces. Pour plus de renseignements, consultez la page 19.

Selectionnnez le cycle

Pour choisir un cycle, appuyez sur le bouton de commande

(position arret) et tournez-le vers la droite (sens horaire)

jusqu'fl ce que I'aiguille soit sur le nombre de minutes

necessaires selon la charge de linge.

IMPORTANT: Pour un entretien optimal des tissus, il faut

choisir la vitesse appropriee de lavage et d'essorage en

fonction du type de charge, fl I'aide du bouton de vitesse de

Wash/Spin Speed (lavage/essorage).

Cottons Cycle (cycle coton)

Pour les tissus normaux, selectionnez la duree du cycle et

mettez le bouton de vitesse de Wash/Spin Speed

(lavage/essorage) sur (normale/normale).

Tirez le bouton de commande

pour demarrer

Vous pouvez arr0ter la laveuse fl tout moment en appuyant

tout simplement sur le bouton de commande. II est ainsi

possible d'obtenir un trempage sans brassage ou de

raccourcir, passer ou repeter route pattie du cycle de lavage.

Le bouton de commande doit etre eafoace (position arre0

Iorsque vous effectuez des modifications.

Remarque - N'essayez pas de tourner le bouton

de commande dans le sens antihoraire. Cela

endommagerait la minuterie.

Corocterisliquesspecioles

Distributeur de javellisant

liquide

Le distributeur dilue automatiquement le javellisant liquide

avant qu'il atteigne le linge.

Pour I'utiliser, proc_der comme suit :

1. Mesurer la quantite de javellisant liquide avec soin en

suivant les instructions sur le recipient.

2 Verser le javellisant liquide dans le distributeur de

javellisant avant d'ajouter le linge. I_viter les

eclaboussures ou le debordement du distributeur.

Remarques •

Ne jamais verser de javellisant liquide non dilue

directement sur le linge ou dans la cuve. Ce produit

chimique est puissant et peut endommager les tissus,

en les dechirant ou decolorant, s'il n'est pas utilise

correctement.

Lorsqu'unjavellisant sans chlore et sans danger pour

les couleurs est utilis& le verser dans la cuve avec le

detergent. Ne pas verser de javellisant sans chlore

dans le distributeur de javellisant.

Distributeur de liquide

Le distributeur de liquide peut etre utilise pour I'assouplisseur

de tissus avec la plupart des cycles ou pour le detergent

liquide avec les cycles Stain Cleaner ou Soak

(detachage/trempage) (certains modeles). Le distributeur de

liquide doit etre nettoye avant et apres

chaque utilisation de detergent liquide. Le distributeur dilue

automatiquement le liquide au moment opportun durant le

cycle.

Pour I'utiliser, preceder comme suit :

1. Verser la quantite voulue de liquide dans le distributeur,

jusqu'au repere de remplissage seulement.

2. Si le liquide arrive sous la ligne, ajouter de I'eau tiede.

S'il devient n6cessaire de nettoyer le distributer :

1. Retirez le distributeur du haut de I'agitateur.

2. Trempez-le pendant une heure dans I'evier ou dans un

recipient dans une solution d'eau chaude et de

detergent liquide pour la vaisselle.

3. Mettez les mains sur le dessus et le dessous du

distributeur et secouez-le, pour deloger les depots des

c6tes du distributeur.

4. Le rincer _ I'eau chaude.

5. Repetez au besoin le processus.

6. Remettre le distributeur sur I'agitateur.

N'utilisez pas de liquide pour la vaisselle

I'interieur de la laveuse, il y aurait risque

d'un exces de mousse.

Soak Cycle I:trempage) [certaigs modbles)

Le cycle stain cleaner evite d'avoir _ faire tremper du linge

tache avant de le mettre dans la laveuse il faut :

1. Ajouter du detergent liquide ou en poudre dans la cuve

de la laveuse.

2. Ajouter le linge.

3. Ajouter du d_tergentliquide, seulement dans le

distributeur de detergent liquide, en haut de I'agitateur.

4. Tourner le bouton pour permettre le demarrage du

cycle Soak.

Le linge va tremper pendant 30 minutes, avec de breves

periodes d'agitation. Ensuite, le linge est essor& de I'eau de

lavage propre est ajoutee ainsi que du detergent liquide,

pour un cycle de 16-minute environ.

Essorage s curitaire

Si pour une raison quelconque le couvercle de la laveuse est

ouvert pendant le cycle d'essorage ou la periode

d'extraction, I'essorage sera interrompu immediatement pour

votre securit& Si la laveuse ne s'arrete pas, appeler

immediatement un technicien. Lorsque le couvercle est

referm& I'essorage se poursuit automatiquement.

La page charge ...

Admiral AAV7000AWW Manuel utilisateur

Marque: Admiral

Modèle: AAV7000AWW

Catégorie: Machines à laver

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Admiral AAV7000AWW User manual
español: Admiral AAV7000AWW Manual de usuario

Admiral AAV7000AWW Manuel utilisateur

Admiral AAV7000AWW Manuel utilisateur

dans d''autres langues

Autres documents