Breville CBL920 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur
EN INSTRUCTION BOOK FR-CA MANUEL D'INSTRUCTIONS ES-MX MANUAL DE INSTRUCCIONES
the Super Q Pro
Instruction Book – CBL920
2
IMPORTANT
SAFEGUARDS
READ ALL
INSTRUCTIONS BEFORE
USE AND SAVE FOR
FUTURE REFENCE
Remove and discard all
packaging materials and
stickers before first use.
To avoid choking hazard
for young children, remove
and safely dispose the
protective cover fitted
on the power plug.
Do not use it in moving
vehicles or boats, do not
use it outdoors, and do not
use it for anything other
than its intended use.
Misuse can cause injury.
Close supervision is
necessary when any
appliance is used by
or near children.
This appliance can be
used by persons with
reduced physical, sensory
or mental capabilities or
lack of experience and
Contents
BREVILLE |
COMMERCIAL
RECOMMENDS
SAFETY FIRST
At Breville | Commercial we
are very safety conscious.
We design and manufacture
consumer products with
the safety of you, our valued
customer, foremost in mind.
In addition we ask that you
exercise a degree of care when
using any electrical appliance
and adhere to the following
2 Breville | Commercial
Recommends Safety First
8 Components
10 Functions
12 Tips
13 Blending Chart (Jug)
15 Care & Cleaning
17 Troubleshooting
3
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and if they understand
the hazards involved.
Do not use the appliance
near the edge of a
countertop or table. Ensure
the surface is level, clean
and free of water and
other substances. Please
be aware that vibration
during use may cause
the appliance to move.
Do not use the appliance
on (or close to) a hot
gas or electric burner,
or where it could touch a
heated oven or surface.
Do not allow the cord
to hang over the edge
of a countertop, or to
become knotted.
To avoid electric shock,
do not immerse the cord,
plug or motor base in
water (or other liquids).
This appliance is
equipped with a power
cord having a grounding
wire with a grounding
plug. The appliance must
be grounded using a
3-hole properly grounded
outlet. In the event of an
electrical short circuit,
grounding reduces the
risk of electrical shock.
If the power outlet is
a standard 2-prong
wall outlet, it is your
personal responsibility
and obligation to have it
replaced with a properly
grounded 3-prong wall
outlet. Do not, under any
circumstances, cut or
remove the third (ground)
prong from the power
cord or use an adapter.
In order to avoid the
possible hazard of the
blender starting by
itself due to inadvertent
resetting of the overload
protector on the motor,
do not attach an external
switching device (such
as a timer) or connect
the blender to a circuit
4
that can regularly switch
the blender on and off.
Do not operate appliance
with a damaged cord or
plug, or after appliance
malfunctions, or if dropped
or damaged in any way.
Immediately cease use
of the appliance and visit
www.BrevilleCommercial.
com or call Breville |
Commercial Consumer
Support for examination,
repair or adjustment.
SAFEGUARDS
FOR YOUR
BLENDER
Wash the blender jug with
warm soapy water before
first use.
Use only the blender jug
and lid that is supplied
with this blender. The use
of attachments, including
canning jars or accessories
not manufactured or
specified by Breville |
Commercial may cause
the risk of fire, electrical
shock, or injury.
Always ensure the blender
is assembled properly
before using. Lid must be
firmly secured to the jug
before operation to ensure
internal contents do not
escape, spray or overflow.
Always ensure the
appliance is properly
assembled as per
instruction before use.
Using the appliance
without being properly
assembled may cause
product malfunction,
product damage or pose
safety risk including
personal injury.
If the motor is straining
under a heavy load, do
not operate continuously
for more than 10 seconds.
Allow the motor to rest
for 1 minute between uses
on heavy loads. Note
that none of the recipes
in these instructions are
considered a heavy load.
Do not leave the blender
unattended when in use.
5
Flashing light indicates
ready to operate. Avoid
any contact with blades
or moving parts.
Keep hands, fingers, hair
and clothing away from
the blender during use.
Always turn blender off
and unplug at the wall
before reaching inside.
Be careful when handling
the blender jug as the
blades are very sharp. Be
careful when emptying the
jug and during cleaning.
Mishandling of the blades
may cause injury.
Do not remove the jug
from the motor base
while blender is in use.
The blender is intended
for food or drinks
preparation. Do not use for
anything other than food
or drinks. Do not operate
without any ingredients
in the blender jug.
Never attempt to operate
with damaged blades,
or with utensils, or any
foreign objects inside
the blender jug.
To reduce the risk of
severe injury to persons
or damage to the blender,
keep hands and utensils
out of the jug while
blending. The scraper
and tamper provided
can be used, provided
the main lid is in place.
Never blend boiling hot
liquids. Allow temperature
to drop before putting
into the jug for blending.
Be careful if hot liquid is
poured into the blender,
as it can be ejected
out of the jug due to
sudden steaming.
When blending hot
liquids ensure inner
measuring cap is in place.
Cap will protect from
splashing of hot liquids
during blending and
includes vents designed
to relieve pressure and
avoid steam build up.
6
When blending hot
liquids, do not exceed
the hot liquids maximum
of 40oz. (1.2L).
Be careful removing the
lid after blending hot
liquids, as steam traps can
form in the liquid and be
ejected out of the jug.
Strictly observe the
reduced capacity
limit for blending hot
ingredients. Failing to
follow this instruction
may cause personal injury
by hot liquid burn.
Never use attachments or
accessories that are not
supplied with this product
or authorized by Breville |
Commercial to be used
on this product. Failing to
follow this instruction may
cause product malfunction,
product damage or
even pose safety risk.
For optional accessories
authorized by Breville |
Commercial to be used on
this product, please read
all instructions supplied
with the accessory in
conjunction with the
instructions contained
in this booklet.
Do not put the blender
jug in extremes of heat
or cold, for example
placing a cold jug into
hot water, or vice versa.
Before moving the blender,
cleaning or putting it
away for storage, always
turn blender off and
unplug at the wall.
BREVILLE ASSIST™
PLUG
Your Breville | Commercial
appliance comes with
a unique Assist™ Plug,
conveniently designed
with a finger hole to ease
removal from the power
outlet.
7
SHORT CORD
INSTRUCTIONS
Your Breville | Commercial
appliance is fitted with a
short power supply cord to
reduce personal injury or
property damage resulting
from pulling, tripping or
becoming entangled with a
longer cord. If an extension
cord is used, (1) the marked
electrical rating of the
cord set or extension cord
should be at least as great
as the electrical rating of
the appliance, (2) the cord
should be arranged so
that it will not drape over
the countertop or table-
top where it can be pulled
on by children or tripped
over unintentionally and
(3) the extension cord
must include a 3-prong
grounding plug.
SAVE THESE INSTRUCTIONS
8
Rating Information
Components
A
B
C
D
E
F
H
KJ
L
N
M
I
G
120 V ~60 Hz 1800 W
9
A. Inner measuring cup
Removable for quick addition
of ingredients.
B. High performance lid
Withstands high velocity tasks,
and is designed to vent steam
and prevent splatter.
C. 68 fl oz (2L) BPA-Free* jug
Impact resistant, shatter proof
and dishwasher safe.
D. Extra-wide, heavy duty blade
and bowl system
Designed with 4 powerful stainless steel
blades contoured to the base of the jug for
maximum cutting power and processing
results including liquid-free processing.
E. Heavy duty metal coupling
For durable and long lasting performance
under demanding conditions.
F. Heavy duty 1800W motor
High velocity power combined with high
torque for outstanding results.
G. LCD indicator with timer
Counts down for pre-programmed settings,
and counts up for speed dial settings.
H. Durable base
I. 5 preset programs
Optimize the blender’s capabilities
for crushing ice, smoothies, stir, boost
and A Bit More™.
J. Overload protection
Resettable thermal fuse for motor protection.
K. Manual speed control
Wide speed range from super slow
stir up to high speed milling
for precise control.
ACCESSORIES
L. Scraper
Designed to push food down from the
walls, or for easily removing ingredients
after blending. Always use scraper with
the blender lid on (inner cap removed).
M. Tamper
Helps make frozen desserts, nut butters and
dips by pushing thick foods directly into the
blades. Always use tamper with the blender
lid on (inner cap removed).
N. 68 fl oz (2L) BPA-Free* jug
Impact resistant, shatter proof
and dishwasher safe.
COPOLYESTER MATERIAL
This blender jug is made with copolyester,
which is a tough, BPA – Free polymer
used to make housewares products that
can stand up to extreme use and repeated
dishwasher cleaning. Products made from
copolyester are impact resistant and shatter
resistant and stay clear and durable even
after hundreds of cycles in the dishwasher.
* Breville | Commercial makes its BPA Free claim for this product
based on independent laboratory testing performed for all the food
contact plastic materials of the product per EU Commission
Regulation No 10/2011. BPA Free Material is used in all parts
that come into contact with food.
10
Functions
GETTING STARTED
Ready mode
Press ON | OFF button to power the unit
to READY mode.
Sleep
After 2 minutes of inactivity, LCD powers
off, and the ON | OFF button flashes red.
After 5 minutes of inactivity, the blender
turns power OFF. Press the ON | OFF
button to reactivate the blender.
VESSELS
This unit features two blending vessels.
The Blender base automatically detects
the vessel and adjusts blending times in
pre-set programs to optimize food results.
68-ounce Jug
The jug is recommended for big volumes up
to 68 ounces and can be used with all
pre-set programs.
PAUSE / CANCEL
For Manual Blending:
First press pauses the selected speed.
Second press cancels the selected speed.
Turn the Dial to start blending again.
For Program Blending:
First press pauses selected program.
Second press cancels the selected program.
Press the program button to start the
program again.
SMOOTHIE
PULSE
ICE CRUSH
O
N
OF
F
+
CLEAN TIMER
STIR BOOST
A BIT
MORE
C
A
N
CE
L
PAUS
E
11
MANUAL OPERATION
Speed Control Dial
Turn the Speed Control Dial clockwise
to select one of 12 speed settings from a
slow STIR through to a very fast MILL.
To stop blending, turn the Speed Control
Dial counterclockwise back to READY.
The blender is programmed to allow manual
speeds to run for a total of 6 minutes
(68-ounce Jug).
WARNING
Never blend boiling hot liquids.
Allow temperature of ingredients
to cool down to room temperature
before placing into blender jug.
PRESET PROGRAMS
PULSE | ICE CRUSH
A program of continuous pulsing
designed to chop food into an even
consistency or crush ice cubes.
SMOOTHIE
For dairy-based smoothies. A combination
of speeds and pulses designed to
combine and aerate ingredients into
a smooth and creamy texture.
STIR
This program bypasses the intermittent
start / stop feature of the low speed manual
blending. It is designed for constant low
speed blending when making emulsifications
or working with low volumes of liquid.
BOOST
A one-touch program to reach
maximum speed quickly and blend
the contents to a fine consistency.
Use the tamper for best results.
A BIT MORE™
The A BIT MORE™ program is designed to
produce a slightly finer texture across chunky
mixtures and fine blends or to incorporate
seasoning after tasting without over-blending.
TIMER
A precision speed control dial allows the
user to set the perfect blending speed
in conjunction with a built in 6-minute
timer that will auto-stop the blend.
CLEAN
Use to remove most of the ingredients off the
blender walls and blades. Add 4 cups of warm
soapy water to the blender jug and press the
CLEAN button. For harder to clean, sticky or
thick ingredients, add ½ teaspoon of liquid
dish detergent for extra cleaning power. For
best results, clean the blender jug this way
immediately after use.
NOTE
If the blender is running and you press
a different preset button, it will switch
to that program without stopping. If a
program is running and you press the
same program button again, it will pause
that program and timer. To resume press
the same program button again.
12
Tips
The inner measuring cap can be removed to
add oils/liquids or other ingredients during
blending. Extreme care must be taken as
depending on the mixture volume and speeds
of operation, splashes can eject from the lid.
We do not recommend removing the inner
measuring cap when blending hot liquid.
Do not exceed the maximum mark when
adding foods and liquids into the blender.
Run the blender only for the appropriate
amount of time required – do not over
blend ingredients.
Use the PULSE | ICE CRUSH button
when food is too thick or coarse to
circulate within the blender jug.
The scraper and tamper accessories can
be used during blending by removing
the inner measuring cap. Always make
sure the main lid stays firmly in place.
Ingredients may stick to the sides of
the blender jug. To push food back
onto the blades with the main lid on
(inner cap removed), use the tamper
provided to scrape down the sides of
the jug, and continue blending.
If any moisture or liquid spills on top of
the motor base during blending, turn the
blender off and unplug from the outlet.
Remove the blender jug, and wipe motor base
immediately with a dry cloth or paper towel.
The optimum amount of ice cubes that the
blender can process in the jug is 8 ounces
(225g). That’s approximately 10 ice cubes.
When the blender has been running for
6 minutes in manual mode with the jug it will
automatically turn off. This is a safety
feature to protect the motor.
Thicker mixtures puree more efficiently
if the jug is ¼ to ½ full.
Do not use metal utensils, as they may
damage the blades or blender jug.
Dates and other dried fruits may vary in
hardness and moisture content. If adding
dried fruits to smoothies, use the tamper for
the first 15–20 seconds of the SMOOTHIE
setting.
To make nut milks, add 1–2 cups of raw
or soaked/drained nuts. Add 3–4 cups of
purified water, and process on MILL for 1
minute. Strain through a nut milk bag (or
muslin/cheesecloth) over a large bowl or jug.
Close bag and squeeze the pulp in the bag
to extract as much milk as you can.
To soak or not to soak nuts? This is a personal
preference and you can make nut milks with
unsoaked or soaked almonds. Almonds are a
great source of protein however they contain
a naturally occurring compound that may
prevent our enzymes from digesting the
nuts effectively. Try soaking nuts overnight
to help break down the compound. Always
rinse and drain soaked nuts before use.
Roasting nuts to make nut butter allows their
natural oils to be released during blending,
and enriches the flavor. Some nuts, such
as almonds and hazelnuts, have a lower
oil content. Add rice bran, macadamia or
coconut oil when blending, if needed.
Freshly milled whole grain flour does
not keep as long as commercial flours.
This is because the inner layers of the
grain contain rich oils, which can become
rancid over time with exposure to heat
and moisture. Always store your flour in
an airtight container in a cool, dry place.
Flour can be stored in the refrigerator
or freezer in warm/humid climates.
Corn, soy beans and some other dried
legumes and grains vary in their moisture
content, and may not circulate properly
during milling. Use the scraper or tamper
during milling to assist with circulation.
To remove any food that cannot easily be
scraped out from under the blades, replace lid
and turn blender back on high speed for 4–5
seconds to spin foods out from under blades.
13
Blending Chart (Jug)
FOOD PREPARATION
& USAGE
QUANTITY FUNCTIONS TIME
Grains & seeds
Mill into flour. Use in
bread, pizza doughs,
cakes, muffins and
flour batters.
1L–3L cups
250–600g MILL speed 30–60 secs
Dried beans,
grains & corn
e.g. wheat,
garbanzo beans,
corn kernels
Mill into flour. Use
for breads, cakes,
muffins, pancakes.
1¼–3cups
250–630g MILL speed 30 - 60 secs
Spices
To make ground spices.
Use whole spices
except for cinnamon
sticks that need to be
broken half. Store in
airtight containers.
Minimum
¼ cup
8–16
cinnamon
sticks
MILL speed 20–30 secs
Raw nuts
To make nut meal.
Use in cakes, cookies
and muffins.
½–2½ cups
100–500g MILL speed 8–15 secs
Toasted nuts To make nut butters
and spreads.
1½–3 cups
300–500g
PUREE speed
with tamper 1 minute
Granulated sugar
Mill to make pure
icing sugar or
powdered sugar.
1–2 cup
200–400g MILL speed 15–30 secs
Raw vegetables
Peel and cut into
¾-inch (2cm) cubes.
Finely chopped. Use for
stuffing, filling, sauces,
stews and casseroles.
8oz
225g CHOP speed 4–6 secs
Graham crackers /
cookies
Break cookies in
half. Blend to form
crumbs. Use for
cheesecake crusts.
8oz
225g
PULSE |
ICE CRUSH 20–30 secs
DRY MILLING
Please note that milling hard ingredients like spices, nuts, sugar, coffee, grains, etc. will cause
scratching and clouding to the inside surfaces of the jug. This is a cosmetic result from milling
these kinds of ingredients, and does not affect the performance of the jug.
Avoid over-processing spices though. Essential oils found in spices when combined with heat
can damage the jug surface.
14
FOOD PREPARATION
& USAGE
QUANTITY FUNCTIONS TIME
Bread crumbs
Remove crusts. Cut
bread into 1 inch
(2½ cm) cubes. Use
in crumb coatings,
stuffings or in meatballs
and meat patties.
(up to 5 slices)
120–400g MIX speed 20 – 30 secs
Mayonnaise
Mix the egg yolk,
mustard and vinegar
or lemon juice. Add
oil slowly through the
lid. Use for dressing.
Up to 4 egg
yolks and
2 cups of oil.
STIR program 1 min 30 secs
Hard cheeses
(like Parmesan
and Pecorino)
Cut into 1½ inch
(3cm) cubes.
Use in creamy sauces,
pasta dishes.
4½ ounces
Max 250g CHOP speed 15-25 secs
Cream
Whip cream to firm
peaks. Add sugar or
vanilla before blending,
if desired.
1 - 2½ cups
240–600mL CHOP speed 25 - 60 secs
This blending chart should be used as a guide only.
15
Care & Cleaning
Vessels and lids
In order to keep your jug clean and avoid food
drying on the blades, vessels and lids, follow
the below steps as soon as possible after use:
Rinse most of the ingredients off the
vessels and lids.
68-ounce jug
Add 4 cups (around 1L) of warm water and
press the CLEAN button. If thick or sticky
ingredients require extra cleaning power
add a few drops of dish liquid detergent.
Rinse the jug and lid again and/or
wash separately in warm soapy water
with a soft cloth or bottle brush.
WARNING
Oils in citrus rind can damage the
material of the jug if left to sit on the jug
for too long. Always clean your blender jug
immediately after processing citrus rind.
Sanitizing
The recommended sanitizing solution is
1½ tsp (7.5mL) of household bleach in
2 quarts (2L) of clean, cool water,
mixed according to the recommended
instructions on the bleach container.
To sanitize, follow the below steps:
1. After performing the auto clean cycle
as per the instructions above, add
half of the recommended sanitizing
solution (1 quart/1L) to the jug. Secure
the lid and inner lid and press CLEAN
to run a sanitizing clean cycle.
2. Allow to stand for 1 minute,
then empty solution.
3. To sanitize all the lids, scraper and
tamper soak them in 1 quart (1L) of the
sanitizing solution mixture for 2 minutes.
4. Place the empty jug and lid back on
blender base and run on manual speed
MIX for 10-20secs to remove any
excess moisture from the blade area.
5. Do not rinse after sanitizing. Allow
to air dry before storage. Rinse with
clean water prior to next use.
16
Motor base
To clean the motor base, wipe with a soft,
damp cloth then dry thoroughly. Wipe any
excess food particles from the power cord.
Cleaning agents
Do not use abrasive scouring pads or
cleaners on either the motor base or the
jug, as they may scratch the surface. Use
only warm soapy water with a soft cloth.
Dishwasher
The blender jug, tamper, scraper and all
lids can be washed in the dishwasher
on a standard wash cycle. Jug can be
placed on the bottom shelf, and all lids
should be washed on the top shelf only.
Stubborn food stains and odors
Strong smelling foods such as garlic, fish and
some vegetables such as carrots may leave
an odor or stain on the blender jug, and lids.
To remove, soak blender jug and lids for 5
minutes in warm soapy water. Then wash with
a mild detergent and warm water, rinse well
and dry thoroughly. Store jug with the lid off.
Storage
Store your blender upright with the blender
jug assembled on the motor base, or
beside it. Do not place anything on top.
To allow air to circulate, keep the lid off.
Dry milling
Please note that milling hard ingredients
like spices, nuts, sugar, coffee, grains,
etc. will cause scratching and clouding
to the inside surfaces of the jug.
This is a cosmetic result from milling
these kinds of ingredients, and does not
affect the performance of the jug.
17
Troubleshooting
Motor doesn’t start or
blade doesn’t rotate Check the blender jug and lid are securely in place.
Check that the power plug is properly inserted into the power outlet.
Check the ON | OFF button and selected function button is illuminated.
Food is unevenly
chopped Use the tamper when blending to help move the ingredients around.
Reduce the speed so the blades have more chance of grabbing the food.
This can happen when too much food is being blended at one time. Try a
smaller amount, and work in batches if necessary.
The ingredients may be too large. Try cutting into smaller pieces. For best
results, ingredients should be in pieces no larger than ¾-inch (2cm).
Food is chopped too
fine or is watery Try blending for shorter period of time or slower speeds.
Use the PULSE | ICE CRUSH function for better control.
Food sticks to
blade and jug The mixture may be too thick. Try adding more liquid and/or using a slower
speed for blending.
Blender overloaded This blender has dual motor protection features to protect against
over heating and/or over current use. When activated, OVERLOAD
PROTECTION will flash on the LCD and the blender will be inoperable.
If activated, turn the blender off by pressing the ON | OFF button on the
control panel, and unplug the blender. On the underside of the unit is a red
RESET button. Press the Button to reset the unit. Wait a few minutes then
re-plug and power ON the blender.
If OVERLOAD PROTECTION is still flashing, repeat and leave the blender
to cool down for at least 20–30 minutes. Once OVERLOAD PROTECTION
has disappeared from the screen the blender is ready to be used again.
We recommend blending in smaller batches, or cutting ingredients into
smaller pieces.
18
Notes
FR-CA MANUEL D'INSTRUCTIONS
the Super Q Pro
Manuel d’instructions – CBL920
2
IMPORTANTES
MESURES DE
CURITÉ
LISEZ TOUTES LES
INSTRUCTIONS AVANT
USAGE ET CONSERVEZ-
LES À TITRE DE
RÉFÉRENCE
Retirez et jetez tout
le matériel d’emballage
et les étiquettes avant
la première utilisation.
Pour éviter tout risque de
suffocation chez les jeunes
enfants, retirez et jetez
en lieu sûr l’enveloppe
protectrice recouvrant
la fiche d’alimentation.
Ne l’utilisez pas dans un
véhicule ou un bateau en
mouvement, ni à l’extérieur
ou à d’autres fins que
celles pour lesquelles
il a été conçu. Une
mauvaise utilisation peut
entrainer des blessures.
Surveillez attentivement
les enfants qui utilisent
ou sont à proximité
de l’appareil.
Table des
matières
BREVILLE |
COMMERCIAL
VOUS
RECOMMANDE
LA SÉCURITÉ
AVANT TOUT
Chez Breville | Commercial,
la sécurité occupe une place
de choix. Nous concevons et
fabriquons des produits de
consommation sans jamais
perdre de vue la sécurité de
notre précieuse clientèle. De
plus, nous vous demandons
d’être très vigilant lorsque vous
utilisez un appareil électrique
et de respecter les mesures de
sécurité suivantes.
2 Breville | Commercial vous
recommande la sécurité avant tout
9 Composants
11 Fonctions
13 Trucs
14 Tableau de mélange (Récipient)
16 Entretien & nettoyage
18 Guide de dépannage
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

Breville CBL920 Manuel utilisateur

Catégorie
Mélangeurs
Taper
Manuel utilisateur

dans d''autres langues