Breville the Q Manuel utilisateur

Instruction Book - BBL820

the Q

TM

2

BREVILLE

RECOMMENDS

SAFETY FIRST

At Breville we are very safety

conscious. We design and

manufacture consumer

products with the safety of you,

our valued customer, foremost

in mind. In addition we ask that

you exercise a degree of care

when using any electrical

appliance and adhere to the

following precautions.

IMPORTANT

SAFEGUARDS

READ ALL

INSTRUCTIONS BEFORE

USE AND SAVE FOR

FUTURE REFENCE

• Remove and discard all

packaging materials and

stickers before ﬁrst use.

• To avoid choking hazard

for young children, remove

and safely dispose the

protective cover ﬁtted

on the power plug.

• This appliance is for

household only. Do not

use it in moving vehicles

or boats, do not use it

outdoors, and do not use

it for anything other than

its intended use. Misuse

can cause injury.

• Close supervision is

necessary when any

appliance is used by

or near children.

• This appliance can be

used by persons with

reduced physical, sensory

2 Breville Recommends

Safety First

8 Components

10 Functions

12 Tips

13 Blending Chart

15 Troubleshooting

16 Care & Cleaning

Contents

3

or mental capabilities or

lack of experience and

knowledge if they have

been given supervision or

instruction concerning use

of the appliance in a safe

way and if they understand

the hazards involved.

• Do not use the appliance

near the edge of a

countertop or table.

Ensure the surface is level,

clean and free of water and

other substances. Please

be aware that vibration

during use may cause the

appliance to move.

• Do not use the appliance

on (or close to) a hot gas

or electric burner, or where

it could touch a heated

oven or surface.

• Do not allow the cord

to hang over the edge

of a countertop, or to

become knotted.

• To avoid electric shock,

do not immerse the cord,

plug or motor base in

water (or other liquids).

• This appliance is

equipped with a power

cord having a grounding

wire with a grounding

plug. The appliance must

be grounded using a

3-hole properly grounded

outlet. In the event of an

electrical short circuit,

grounding reduces the

risk of electrical shock.

• If the power outlet is

a standard 2-prong

wall outlet, it is your

personal responsibility

and obligation to have it

replaced with a properly

grounded 3-prong wall

outlet. Do not, under any

circumstances, cut or

remove the third (ground)

prong from the power

cord or use an adapter.

• In order to avoid the

possible hazard of the

blender starting by

itself due to inadvertent

resetting of the overload

protector on the motor,

do not attach an external

switching device (such

4

as a timer) or connect

the blender to a circuit

that can regularly switch

the blender on and off.

• Do not operate appliance

with a damaged cord or

plug, or after appliance

malfunctions, or if dropped

or damaged in any way.

Immediately cease use

of the appliance and

visit www.Breville.com

or call Breville Consumer

Support for examination,

repair or adjustment.

SAFEGUARDS

FOR YOUR

BLENDER

• Wash the blender jug with

warm soapy water before

ﬁrst use.

• Use only the blender jug

and lid that is supplied

with this blender. The use

of attachments, including

canning jars or accessories

not manufactured or

speciﬁed by Breville may

cause the risk of ﬁre,

electrical shock, or injury.

• Always ensure the blender

is assembled properly

before using. Lid must be

ﬁrmly secured to the jug

before operation to ensure

internal contents do not

escape, spray or overﬂow.

• Always ensure the

appliance is properly

assembled as per

instruction before use.

Using the appliance

without being properly

assembled may cause

product malfunction,

product damage or pose

safety risk including

personal injury.

• If the motor is straining

under a heavy load, do not

operate continuously for

more than 10 seconds.

Allow the motor to rest

for 1 minute between uses

on heavy loads. Note that

none of the recipes in these

instructions are considered

a heavy load.

• Do not leave the blender

unattended when in use.

• Flashing light indicates

ready to operate. Avoid

5

any contact with blades

or moving parts.

• Keep hands, ﬁngers,

hair and clothing away

from the blender during

use. Always turn blender

off and unplug at the wall

before reaching inside.

• Be careful when handling

the blender jug as the

blades are very sharp.

Be careful when emptying

the jug and during cleaning.

Mishandling of the blades

may cause injury.

• Do not remove the jug

from the motor base while

blender is in use.

• The blender is intended for

food or drinks preparation.

Do not use for anything

other than food or drinks.

Do not operate without

any ingredients in the

blender jug.

• Never attempt to operate

with damaged blades, or

with utensils, or any

foreign objects inside the

blender jug.

• To reduce the risk of severe

injury to persons or

damage to the blender,

keep hands and utensils out

of the jug while blending.

The tamper provided can

be used, provided the main

lid is in place.

• Be careful if hot liquid is

poured into the blender, as

it can be ejected out of the

jug due to sudden steaming.

• When blending hot liquids

ensure inner measuring cap

is in place. Cap will protect

from splashing of hot

liquids during blending and

includes vents designed to

relieve pressure and avoid

steam build up.

• When blending hot liquids,

do not exceed the hot liquids

maximum of 40oz. (1.2L).

• Be careful removing the lid

after blending hot liquids,

as steam traps can form in

the liquid and be ejected

out of the jug.

• Do not put the blender

jug in extremes of heat or

cold, for example placing

a cold jug into hot water,

or vice versa.

• Before moving the blender,

6

cleaning or putting it away

for storage, always turn

blender off and unplug

at the wall.

• Strictly observe the reduced

capacity limit for blending

hot ingredients. Failing to

follow this instruction may

cause personal injury by

hot liquid burn.

• Never blend hot

ingredients/liquid using

the vacuum blending

feature. (Vacuum blending

is an optional feature

achieved through using the

Breville vacuum pump

supplied separately.)

• Never use attachments

or accessories that are not

supplied with this product

or authorised by Breville

to be used on this product.

Failing to follow this

instruction may cause

product malfunction,

product damage or even

pose safety risk.

• For optional accessories

authorised by Breville

to be used on this product,

please read all instructions

supplied with the accessory

in conjunction with the

instructions contained

in this booklet.

BREVILLE ASSIST™

PLUG

Your Breville appliance

comes with a unique

Assist™ Plug, conveniently

designed with a ﬁnger hole

to ease removal from the

power outlet.

SHORT CORD

INSTRUCTIONS

Your Breville appliance is

ﬁtted with a short power

supply cord to reduce

personal injury or property

damage resulting from

pulling, tripping or

becoming entangled with a

longer cord. If an extension

cord is used, (1) the marked

electrical rating of the cord

set or extension cord should

be at least as great as the

electrical rating of the

appliance, (2) the cord

should be arranged so that

7

FOR HOUSEHOLD USE ONLY

SAVE THESE INSTRUCTIONS

it will not drape over the

countertop or table-top

where it can be pulled on

by children or tripped over

unintentionally and (3) the

extension cord must include

a 3-prong grounding plug.

8

Components

A

B

C

D

E

F

H

J K

L

I

G

9

Components

A. Inner measuring cup

Removable for quick addition

of ingredients.

B. High performance lid

Withstands high velocity tasks,

and is designed to vent steam

and prevent splatter.

C. 68 ounce BPA-Free* jug

Impact resistant, shatter proof

and dishwasher safe.

D. Extra-wide, heavy duty blade

and bowl system

Designed with 4 powerful stainless steel

blades contoured to the base of the jug for

maximum cutting power and processing

results including liquid-free processing.

E. Heavy duty metal coupling

For durable and long lasting performance

under demanding conditions.

F. Heavy duty 1800W motor

High velocity power combined with

high torque for outstanding results.

G. LCD indicator with timer

Counts down for pre-programmed settings,

and counts up for speed dial settings.

H. Durable base

I. 5 preset programs

Optimize the blender’s capabilities

for crushing ice, smoothies, green

smoothies, soups and cleaning the jug.

J. 5 speed settings

Wide speed range for convenient

speed selection.

K. Overload protection

Resettable thermal fuse

for motor protection.

* Breville makes its BPA Free claim for this product based

on independent laboratory testing performed for all

the food contact plastic materials of the product per EU

Commission Regulation No 10/2011. BPA Free Material

is used in all parts that come into contact with food.

ACCESSORIES

L. Tamper

Helps make frozen desserts, nut butters

and dips by pushing thick foods directly

into the blades. Always use tamper with

the blender lid on (inner cap removed).

COPOLYESTER MATERIAL

This blender jug is made with copolyester,

which is a tough, BPA – Free polymer

used to make housewares products that

can stand up to extreme use and repeated

dishwasher cleaning. Products made from

copolyester are impact resistant and shatter

resistant and stay clear and durable even

after hundreds of cycles in the dishwasher.

BREVILLE ASSIST™ PLUG

Your Breville appliance comes with a unique

Breville Assist

™ Plug, conveniently designed

with a ﬁnger hole for easy removal from the

wall outlet.

10

Functions

GETTING STARTED

Ready mode

Press ON | OFF button to power the unit

to READY mode.

Sleep

After 2 minutes of inactivity, LCD powers

off, and the ON | OFF button ﬂashes red.

After 5 minutes of inactivity, the blender

turns power OFF. Press the ON | OFF

button to reactivate the blender.

CANCEL

The CANCEL function stops the pre-set

program or selected speed setting and sets

the time to 0.

Speed Control Selection

There are 5 electronic speed buttons from

MIX through to MILL.

MIX combines more delicate foods with a

folding motion, and is good for combining

wet and dry ingredients.

MILL is the fastest setting and is ideal for

breaking down ingredients to mill grain

to ﬂour, make nut milk and other ﬁnely

blended mixtures.

Select the required speed (1 to 5) by

pressing the corresponding speed button.

WARNING

Never blend boiling hot liquids. Allow

temperature of ingredients to cool down

to room temperature before placing into

blender jug.

PAUSED

RESET

MIN SEC

OVERLOAD

PROTECTION

ON OFF

AUTO

PULSE

ICE CRUSH

SOUP

COLD

TO HOT

SMOOTHIE GREEN

SMOOTHIE

1

MIX

2

CHOP

3

BLEND

4

PUREE

5

MILL

CLEAN

CANCEL

11

PRESET PROGRAMS

PULSE | ICE CRUSH

A program of continuous pulsing designed

to chop food into an even consistency

or crush ice cubes.

SMOOTHIE

For dairy-based smoothies. A combination

of speeds and pulses designed to combine

and aerate ingredients into a smooth and

creamy texture.

GREEN SMOOTHIE

For blending whole fruits/vegetables into

a smooth beverage. A combination of high

speed proﬁles breaks down tough ﬁbres into

very ﬁne particles. Use the tamper if necessary.

SOUP

This program is exclusively for creating

a Cold to Hot Soup – turning whole

ingredients at room temperature into a

smooth, hot soup. Primarily a high speed

program, the program will ﬁnish with a

slow stir to remove steam bubbles.

NOTE

Raw foods such as meats and seafood need to

be cooked prior to using the SOUP program.

WARNING

Do not add hot ingredients when using

the SOUP program.

CLEAN

Use to remove most of the ingredients

off the blender walls and blades. Add 4

cups of warm soapy water to the blender

jug and press the CLEAN button.

For harder to clean, sticky or thick ingredients,

add ½ teaspoon of liquid dish detergent for

extra cleaning power. For best results, clean

the blender jug this way immediately after use.

NOTE

If the blender is running and you press

a different preset button, it will switch

to that program without stopping. If a

program is running and you press the

same program button again, it will pause

that program and timer. To resume press

the same program button again.

12

Tips

• The inner measuring cap can be removed to

add oils/liquids or other ingredients during

blending. Extreme care must be taken as

depending on the mixture volume and speeds

of operation, splashes can eject from the lid.

We do not recommend removing the inner

measuring cap when blending hot liquid.

• Do not exceed the maximum mark when

adding foods and liquids into the blender.

• Run the blender only for the

appropriate amount of time required

– do not over blend ingredients.

• Use the PULSE | ICE CRUSH button

when food is too thick or coarse to

circulate within the blender jug.

• The tamper accessory can be used

during blending by removing the inner

measuring cap. Always make sure

the main lid stays ﬁrmly in place.

• Ingredients may stick to the sides of

the blender jug. To push food back

onto the blades with the main lid on

(inner cap removed), use the tamper

provided to scrape down the sides of

the jug, and continue blending.

• If any moisture or liquid spills on top of

the motor base during blending, turn the

blender off and unplug from the outlet.

Remove the blender jug, and wipe motor base

immediately with a dry cloth or paper towel.

• The maximum amount of ice cubes that the

blender can process in the jug is 8 ounces

(225g). That's approximately 10 ice cubes.

• Thicker mixtures puree more efﬁciently

if the jug is ¼ to ½ full.

• Do not use metal utensils, as they may

damage the blades or blender jug.

• Dates and other dried fruits may vary in

hardness and moisture content. If adding

dried fruits to smoothies, use the tamper for

the ﬁrst 15–20 seconds of the SMOOTHIE

or GREEN SMOOTHIE setting.

• To make nut milks, add 1–2 cups of raw or

soaked/drained nuts. Add 4 cups of puriﬁed

water, and process on MILL for 1 minute.

Strain through a nut milk bag (or muslin/

cheesecloth) over a large bowl or jug.

Close bag and squeeze the pulp in the bag

to extract as much milk as you can.

• To soak or not to soak nuts? This is a personal

preference and you can make nut milks with

unsoaked or soaked almonds. Almonds are a

great source of protein however they contain

a naturally occurring compound that may

prevent our enzymes from digesting the

nuts effectively. Try soaking nuts overnight

to help break down the compound. Always

rinse and drain soaked nuts before use.

• Roasting nuts to make nut butter allows their

natural oils to be released during blending,

and enriches the ﬂavor. Some nuts, such

as almonds and hazelnuts, have a lower

oil content. Add rice bran, macadamia or

coconut oil when blending, if needed.

• Freshly milled whole grain ﬂour does not keep

as long as commercial ﬂours. This is because

the inner layers of the grain contain rich oils,

which can become rancid over time with

exposure to heat and moisture. Always store

your ﬂour in an airtight container in a cool, dry

place. Flour can be stored in the refrigerator

or freezer in warm/humid climates.

• Corn, soy beans and some other dried

legumes and grains vary in their moisture

content, and may not circulate properly

during milling. Use the tamper during

milling to assist with circulation.

• To remove any food that cannot easily be

scraped out from under the blades, replace lid

and turn blender back on high speed for 4–5

seconds to spin foods out from under blades.

13

Blending Chart

FOOD PREPARATION

& USAGE

QUANTITY FUNCTIONS TIME

Grains & seeds

Mill into ﬂour. Use in

bread, pizza doughs,

cakes, mufﬁns and

ﬂour batters.

1L–3L cups

250g–600g

MILL speed 30–60 secs

Dried beans,

grains & corn

e.g. wheat,

garbanzo beans,

corn kernels

Mill into ﬂour. Use

for breads, cakes,

mufﬁns, pancakes.

1¼–3cups

250g–630g

MILL speed 30–60 secs

Spices

To make ground spices.

Use whole spices

except for cinnamon

sticks that need to be

broken half. Store in

airtight containers.

Minimum

¼ cup

8–16

cinnamon

sticks

MILL speed 20–30 secs

Raw nuts

To make nut meal.

Use in cakes, cookies

and mufﬁns.

½–2½ cups

100g–500g

MILL speed 8–15 secs

Toasted nuts

To make nut butters

and spreads.

1½–3 cups

300g–500g

PUREE speed

with tamper

1 minute

Granulated sugar

Mill to make pure

icing sugar or

powdered sugar.

1–2 cup

200g–400g

MILL speed 15–30 secs

Raw vegetables

Peel and cut into

¾-inch (2cm) cubes.

Finely chopped. Use for

stufﬁng, ﬁlling, sauces,

stews and casseroles.

8oz

225g

CHOP speed 4–6 secs

Graham crackers

/cookies

Break cookies in

half. Blend to form

crumbs. Use for

cheesecake crusts.

8oz

225g

PULSE |

ICE CRUSH

20–30 secs

DRY MILLING

Please note that milling hard ingredients like spices, nuts, sugar, coffee, grains, etc. will cause

scratching and clouding to the inside surfaces of the jug. This is a cosmetic result from milling

these kinds of ingredients, and does not affect the performance of the jug.

Avoid over-processing spices though. Essential oils found in spices when combined with heat

can damage the jug surface.

14

FOOD PREPARATION

& USAGE

QUANTITY FUNCTIONS TIME

Bread crumbs

Remove crusts. Cut

bread into 1 inch

(2½ cm) cubes. Use

in crumb coatings,

stufﬁngs or in meatballs

and meat patties.

(up to 5 slices)

120g–400g

MIX speed 20–30 secs

Mayonnaise

Mix the egg yolk,

mustard and vinegar

or lemon juice. Add

oil slowly through the

lid. Use for dressing.

Up to 4 egg

yolks and

2 cups of oil.

MIX speed 1 min 30 secs

Hard cheeses

(like Parmesan

and Pecorino)

Cut into 1½ inch

(3cm) cubes.

Use in creamy sauces,

pasta dishes.

4½ ounces

Max 250g

CHOP speed 15–25 secs

Cream

Whip cream to ﬁrm

peaks. Add sugar or

vanilla before blending,

if desired.

1–2½ cups

240–600mL

CHOP speed 25–60 secs

This blending chart should be used as a guide only.

15

Troubleshooting

Motor doesn’t

start or blade

doesn’t rotate

•

Check the blender jug and lid are securely in place.

•

Check that the power plug is properly inserted into the power outlet.

•

Check the ON | OFF button and selected function button

is illuminated.

Food is unevenly

chopped

•

Use the tamper when blending to help move the ingredients around.

•

Reduce the speed so the blades have more chance of grabbing

the food.

•

This can happen when too much food is being blended at one time.

Try a smaller amount, and work in batches if necessary.

•

The ingredients may be too large. Try cutting into smaller pieces.

For best results, ingredients should be in pieces no larger than

¾-inch (2cm).

Food is chopped too

ﬁne or is watery

•

Try blending for shorter period of time or slower speeds.

•

Use the PULSE | ICE CRUSH function for better control.

Food sticks to

blade and jug

•

The mixture may be too thick. Try adding more liquid and/or

using a slower speed for blending.

Blender overloaded

•

This blender has dual motor protection features to protect

against over heating and/or over current use. When activated

OVERLOAD PROTECTION will ﬂash on the LCD and the

blender will be inoperable.

•

If activated, turn the blender off by pressing the ON | OFF button

on the control panel, and unplug the blender. On the underside

of the unit is a red RESET button. Press the Button to reset the unit.

Wait a few minutes then re-plug and power ON the blender.

•

If OVERLOAD PROTECTION is still ﬂashing, repeat and

leave the blender to cool down for at least 20–30 minutes.

Once OVERLOAD PROTECTION has disappeared from

the screen the blender is ready to be used again.

•

We recommend blending in smaller batches, or cutting

ingredients into smaller pieces.

16

Care & Cleaning

Jug and Lid

To avoid food drying on blades, jug and lid,

follow the below steps as soon as possible

after use:

• Rinse most of the ingredients off the jug

and lid.

• Add 4 cups (around 1L) of warm water and

1–2 drops of detergent and press the CLEAN

button.

• Rinse the jug and lid again and/or wash

separately in warm soapy water with a soft

cloth or bottle brush.

WARNING

Oils in citrus rind can damage the material

of the jug if left to sit on the jug for too

long. Always clean your blender jug

immediately after processing citrus rind.

Sanitizing

The recommended sanitizing solution is

1½ tsp (7.5mL) of household bleach in 2 quarts

(2L) of clean, cool water, mixed according to

the recommended instructions on the bleach

container. To sanitize, follow the below steps:

1. After performing the auto clean cycle

as per the instructions above, add

half of the recommended sanitizing

solution (1 quart/1L) to the jug. Secure

the lid and inner lid and press CLEAN

to run a sanitizing clean cycle.

2. Allow to stand for 1 minute, then empty

solution.

3. To sanitize the lid and tamper soak

them in 1 quart (1L) of the sanitizing

solution mixture for 2 minutes.

4. Place the empty jug and lid back on

blender base and run on manual speed

MIX for 10-20secs to remove any

excess moisture from the blade area.

5. Wipe the exterior of the lid, jug and

base with a soft cloth dampened

with the sanitizing solution.

6. Do not rinse after sanitizing. Allow

to air dry before storage. Rinse with

clean water prior to next use.

Motor base

To clean the motor base, wipe with a soft,

damp cloth then dry thoroughly. Wipe any

excess food particles from the power cord.

Cleaning agents

Do not use abrasive scouring pads or

cleaners on either the motor base or the

jug, as they may scratch the surface. Use

only warm soapy water with a soft cloth.

Dishwasher

The blender jug, tamper and lid can be

washed in the dishwasher on a standard

wash cycle. Jug can be placed on the

bottom shelf, however the tamper and lid

should be washed on the top shelf only.

Stubborn food stains and odors

Strong smelling foods such as garlic, ﬁsh and

some vegetables such as carrots may leave an

odor or stain on the blender jug and lid.

To remove, soak blender jug and lid for

5 minutes in warm soapy water. Then wash

with a mild detergent and warm water,

rinse well and dry thoroughly. Store jug

with the lid off.

Storage

Store your blender upright with the

blender jug assembled on the motor base,

or beside it. Do not place anything on top.

To allow air to circulate, keep the lid off.

Dry milling

Please note that milling hard ingredients

like spices, nuts, sugar, coffee, grains,

etc. will cause scratching and clouding

to the inside surfaces of the jug.

This is a cosmetic result from milling

these kinds of ingredients, and does not

affect the performance of the jug.

the Q

TM

Manuel d'instructions - BBL820

18

BREVILLE

VOUS

RECOMMANDE

LA SÉCURITÉ

AVANT TOUT

Chez Breville, la sécurité

occupe une place de choix.

Nous concevons et fabriquons

des produits de consommation

sans jamais perdre de vue la

sécurité de notre précieuse

clientèle. De plus, nous

vous demandons d’être très

vigilant lorsque vous utilisez

un appareil électrique et de

respecter les mesures de

sécurité suivantes.

IMPORTANTES

MESURES DE

SÉCURITÉ

LISEZ TOUTES LES

INSTRUCTIONS

AVANT USAGE ET

CONSERVEZ-LES À

TITRE DE RÉFÉRENCE

• Retirez et jetez tout le

matériel d’emballage et

les étiquettes avant la

première utilisation.

• Pour éviter tout risque de

suffocation chez les jeunes

enfants, retirez et jetez

en lieu sûr l’enveloppe

protectrice recouvrant

la ﬁche d’alimentation.

• Cet appareil est conçu

pour usage domestique

seulement. Ne l’utilisez pas

dans un véhicule ou un

bateau en mouvement, ni à

l’extérieur ou à d’autres ﬁns

que celles pour lesquelles

il a été conçu. Une

mauvaise utilisation peut

entrainer des blessures.

• Surveillez attentivement

les enfants qui utilisent

ou sont à proximité

de l’appareil.

18 Breville vous recommande

la sécurité avant tout

24 Composants

26 Fonctions

28 Trucs

29 Tableau de mélange

31 Guide de dépannage

32 Entretien & nettoyage

Table des

matières

19

• Cet appareil peut être

utilisé par des personnes

avec facultés physiques,

sensorielles ou mentales

réduites ou manque

d’expérience ou de

connaissance du produit,

pourvu qu’elles aient été

supervisées ou initiées

à l’usage sécuritaire de

l’appareil et comprennent

les risques qui s’ensuivent.

• N’utilisez pas l’appareil sur

le bord d’un comptoir ou

d’une table. Assurez-vous

que la surface de travail est

plane, propre et exempte

d’eau ou de toute autre

substance. Veuillez noter

que la vibration causée

par le fonctionnement

de l’appareil peut

le faire bouger.

• N’utilisez pas l’appareil

sur (ou près) d’un brûleur

à gaz ou électrique ou à

un endroit où il pourrait

toucher un four ou

une surface chaude.

• Ne laissez pas le cordon

pendre d’un comptoir

ou se nouer.

• Pour éviter tout risque

d’électrocution,

n’immergez pas le

cordon, la ﬁche ou le

socle motorisé dans l’eau

(ou tout autre liquide).

• Cet appareil est équipé

d’un cordon d’alimentation

muni d’un ﬁl de mise à la

terre et d’une ﬁche reliée à

la terre. L’appareil doit être

relié à la terre en utilisant

une prise électrique à trois

alvéoles correctement

reliée à la terre. Dans le

cas d’un court-circuit, la

mise à la terre réduira le

risque de choc électrique.

• Si la prise électrique

est standard à deux

alvéoles, il est de votre

responsabilité et obligation

de la faire remplacer par

une prise à trois alvéoles

correctement reliée à la

terre. Ne tentez d'aucune

façon de couper ou enlever

la troisième broche du

cordon d’alimentation ou

utiliser un adaptateur.

• Aﬁn d'empêcher le

mélangeur de démarrer de

lui-même en raison d’une

réinitialisation accidentelle

20

du limiteur de surcharge

du moteur, ne reliez pas

l’appareil à un dispositif

de commutation externe

(tel qu’une minuterie)

ou ne le branchez pas

sur un circuit qui peut

mettre régulièrement

le mélangeur en

marche et l'arrêter.

• Ne faites pas fonctionner

l’appareil si le cordon ou la

ﬁche sont endommagés, s'il

fonctionne mal, a subi une

chute ou est endommagé

de quelque façon.

Cessez immédiatement

l’utilisation de l'appareil

et visitez www.Breville.

com ou contactez

l'équipe de soutien

aux consommateurs

pour le faire examiner,

réparer ou ajuster.

PRÉCAUTIONS

POUR VOTRE

MÉLANGEUR

• Avant la première

utilisation, lavez le

récipient du mélangeur à

l’eau chaude savonneuse.

• Utilisez uniquement le

récipient et le couvercle

fournis avec ce mélangeur.

L’utilisation d’accessoires

non fabriqués ou

spéciﬁquement non

recommandés par Breville

peut provoquer un risque

d’incendie, d'électrocution

ou de blessure.

• Assurez-vous que

le mélangeur est

correctement assemblé

avant de l’utiliser. Le

couvercle doit être

fermement ﬁxé au

récipient avant la mise en

marche pour éviter que

le contenu ne s’échappe,

soit projeté hors du

récipient ou déborde.

• Assurez-vous toujours

de bien assembler

l’appareil avant de

l’utiliser, tel que stipulé

dans les instructions. Un

assemblage incorrect

peut entraîner un

dysfonctionnement de

l’appareil, l’endommager

ou même présenter

un risque pour la

La page est en cours de chargement...

Breville the Q Manuel utilisateur

Breville the Q Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents