VTech CS6759 Manuel utilisateur

BC

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

User’s manual

CS6758-3

CS6759

CS6759-3

DECT 6.0 cordless telephone

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read

Important safety instructions.

This manual has all the feature operations

and troubleshooting necessary to install and

operate your new VTech telephone. Please

review this manual thoroughly to ensure proper

installation and operation of this innovative and

feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at

www.vtechphones.com.

In Canada, please visit

www.vtechcanada.com.

Telephones identiﬁed with this

logo have reduced noise and

interference when used with

most T-coil equipped hearing

aids and cochlear implants.

The TIA-1083 Compliant

Logo is a trademark of the

Telecommunications Industry

Association. Used under

license.

Important safety

instructions

When using your telephone equipment,

basic safety precautions should always

be followed to reduce the risk of ﬁre,

electric shock and injury, including the

following:

Read and understand all instructions.

Follow all warnings and instructions

marked on the product.

Unplug this product from the wall

outlet before cleaning. Do not use

liquid or aerosol cleaners. Use a

damp cloth for cleaning.

Do not use this product near water

such as near a bath tub, wash bowl,

kitchen sink, laundry tub or swimming

pool, or in a wet basement or shower.

Do not place this product on an

unstable table, shelf, stand or other

unstable surfaces.

Avoid placing the telephone system

in places with extreme temperature,

direct sunlight, or other electrical

devices. Protect your phone from

moisture, dust, corrosive liquids and

fumes.

Slots and openings in the back or

bottom of the telephone base and

handset are provided for ventilation.

To protect them from overheating,

these openings must not be blocked

by placing the product on a soft

surface such as a bed, sofa or

rug. This product should never be

placed near or over a radiator or heat

register. This product should not be

placed in any area where proper

ventilation is not provided.

This product should be operated

only from the type of power source

indicated on the marking label. If

you are not sure of the type of power

supply in your home or ofﬁce, consult

your dealer or local power company.

1.

2.

3.

4.

5.

6.

7.

8.

T

Compatible with

Hearing Aid T-Coil

TIA-1083

Do not allow anything to rest on

the power cord. Do not install this

product where the cord may be

walked on.

Never push objects of any kind into

this product through the slots in the

telephone base or handset because

they may touch dangerous voltage

points or create a short circuit. Never

spill liquid of any kind on the product.

To reduce the risk of electric shock,

do not disassemble this product,

but take it to an authorized service

facility. Opening or removing parts of

the telephone base or handset other

than speciﬁed access doors may

expose you to dangerous voltages or

other risks. Incorrect reassembling

can cause electric shock when the

product is subsequently used.

Do not overload wall outlets and

extension cords.

Unplug this product from the wall

outlet and refer servicing to an

authorized service facility under the

following conditions:

When the power supply cord or

plug is damaged or frayed.

If liquid has been spilled onto the

product.

If the product has been exposed

to rain or water.

If the product does not operate

normally by following the

operating instructions. Adjust only

those controls that are covered

by the operation instructions.

Improper adjustment of other

controls may result in damage and

often requires extensive work by

an authorized technician to restore

the product to normal operation.

If the product has been dropped

and the telephone base and/or

handset has been damaged.

9.

10.

11.

12.

13.

•

If the product exhibits a distinct

change in performance.

14. Avoid using a telephone (other than

cordless) during an electrical storm.

There is a remote risk of electric

shock from lightning.

15. Do not use the telephone to report

a gas leak in the vicinity of the leak.

Under certain circumstances, a spark

may be created when the adapter

is plugged into the power outlet,

or when the handset is replaced in

its cradle. This is a common event

associated with the closing of any

electrical circuit. The user should not

plug the phone into a power outlet,

and should not put a charged handset

into the cradle, if the phone is

located in an environment containing

concentrations of ﬂammable or

ﬂame-supporting gases, unless there

is adequate ventilation. A spark in

such an environment could create a

ﬁre or explosion. Such environments

might include: medical use of

oxygen without adequate ventilation;

industrial gases (cleaning solvents;

gasoline vapors; etc.); a leak of

natural gas; etc.

16. Only put the handset of your

telephone next to your ear when it is

in normal talk mode.

17. The power adapters are intended to

be correctly oriented in a vertical or

ﬂoor mount position. The prongs are

not designed to hold the plug in place

if it is plugged into a ceiling,

under-the-table or cabinet outlet.

SAVE THESE INSTRUCTIONS

Battery

CAUTION: Use Only Supplied

Battery.

Do not dispose of the battery in a fire.

Check with local waste management

•

codes for special disposal instructions.

Do not open or mutilate the battery.

Released electrolyte is corrosive and

may cause burns or injury to the eyes

or skin. The electrolyte may be toxic if

swallowed.

Exercise care in handling batteries in

order not to create a short circuit with

conductive materials.

Charge the battery provided with this

product only in accordance with the

instructions and limitations specified

in this manual.

Precautions for users of implanted

cardiac pacemakers

Cardiac pacemakers (applies only to

digital cordless telephones):

Wireless Technology Research, LLC

(WTR), an independent research entity,

led a multidisciplinary evaluation of the

interference between portable wireless

telephones and implanted cardiac

pacemakers. Supported by the U.S.

Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

Should keep wireless telephones at

least six inches from the pacemaker.

Should NOT place wireless telephones

directly over the pacemaker, such as in

a breast pocket, when it is turned ON.

Should use the wireless telephone at

the ear opposite the pacemaker.

WTR’s evaluation did not identify any

risk to bystanders with pacemakers

from other persons using wireless

telephones.

About cordless telephones

Privacy: The same features that make

a cordless telephone convenient

create some limitations. Telephone

calls are transmitted between the

telephone base and the cordless

•

handset by radio waves, so there is a

possibility that the cordless telephone

conversations could be intercepted

by radio receiving equipment within

range of the cordless handset. For

this reason, you should not think of

cordless telephone conversations as

being as private as those on corded

telephones.

Electrical power: The telephone

base of this cordless telephone must

be connected to a working electrical

outlet. The electrical outlet should not

be controlled by a wall switch. Calls

cannot be made from the cordless

handset if the telephone base is

unplugged, switched off or if the

electrical power is interrupted.

Potential TV interference: Some

cordless telephones operate

at frequencies that may cause

interference to televisions and

VCRs. To minimize or prevent

such interference, do not place

the telephone base of the cordless

telephone near or on top of a TV or

VCR. If interference is experienced,

moving the cordless telephone farther

away from the TV or VCR often

reduces or eliminates the interference.

Rechargeable batteries: Exercise

care in handling batteries in order

not to create a short circuit with

conducting material such as rings,

bracelets and keys. The battery or

conductor may overheat and cause

harm. Observe proper polarity

between the battery and the battery

charger.

Nickel-metal hydride rechargeable

batteries: Dispose of these batteries

in a safe manner. Do not burn or

puncture the battery. Like other

batteries of this type, if burned or

punctured, they could release caustic

material which could cause injury.

•

Table of contents

i

What’s in the box . . . . . . . . . . . . . . . 1

Overview ......................2

Handset overview. . . . . . . . . . . . . . . . . . . 2

Telephone base overview . . . . . . . . . . . . . 3

Charger overview . . . . . . . . . . . . . . . . . . . 4

Display icons overview . . . . . . . . . . . . . . . 5

Handset and Telephone base

lights overview ..................... 5

Connect.......................6

Connect the charger. . . . . . . . . . . . . . . . . 6

Mount the telephone base . . . . . . . . . . . . 6

Install and charge the battery. . . . . . . . . . 7

Charge the battery . . . . . . . . . . . . . . . . . . 8

Before use.....................9

Set date and time . . . . . . . . . . . . . . . . . . 9

Check for dial tone . . . . . . . . . . . . . . . . . . 9

Operating range ....................9

Configure your telephone . . . . . . . 10

Set language ..................... 10

Set date and time . . . . . . . . . . . . . . . . . . 10

Home area code................... 11

Dial mode........................ 11

Telephone Operations . . . . . . . . . . 12

Make a call.......................12

Answer a call ..................... 12

End a call ........................ 12

Speakerphone .................... 12

Volume control ....................13

Mute ............................ 13

Join a call in progress (for multiple

handset models only) . . . . . . . . . . . . . . . 13

Call waiting....................... 13

Chain dialing...................... 13

Find handset...................... 14

Transfer a call..................... 14

Intercom ......................... 15

Answer an incoming call during

an intercom call . . . . . . . . . . . . . . . . . . . 16

Call transfer using intercom . . . . . . . . . . 16

Redial list ....................17

Review a redial list entry. . . . . . . . . . . . . 17

Dial a redial list entry . . . . . . . . . . . . . . . 17

Delete a redial list entry . . . . . . . . . . . . . 17

Directory .....................18

Add a directory entry . . . . . . . . . . . . . . . 18

Review directory entries . . . . . . . . . . . . . 19

Alphabetical search . . . . . . . . . . . . . . . . 19

Delete a directory entry . . . . . . . . . . . . . 19

Dial a directory entry . . . . . . . . . . . . . . . 19

Speed dial........................ 20

Assign a speed dial entry . . . . . . . . . . . . 20

Reassign a speed dial entry. . . . . . . . . . 20

Dial a speed dial number . . . . . . . . . . . . 20

Delete a speed dial entry . . . . . . . . . . . . 21

Caller ID......................21

Review the caller ID log . . . . . . . . . . . . . 21

Memory match ....................22

Missed call indicator . . . . . . . . . . . . . . . . 22

View dialing options . . . . . . . . . . . . . . . . 22

Dial a caller ID log entry . . . . . . . . . . . . . 23

Delete the caller ID log entries . . . . . . . . 23

Sound settings . . . . . . . . . . . . . . . . 24

Key tone ......................... 24

Ringer tone....................... 24

Handset ringer volume . . . . . . . . . . . . . . 24

Telephone base ringer volume . . . . . . . . 24

Temporary ringer silencing . . . . . . . . . . . 25

Quiet mode....................... 25

ii

Table of contents

About the built-in answering

system and voicemail service. . . . 26

Set your built-in answering

system.......................27

Turn the answering system on or off. . . . 27

Default announcement . . . . . . . . . . . . . . 27

Record your own announcement . . . . . . 27

Play your announcement . . . . . . . . . . . . 27

Delete your announcement . . . . . . . . . . 28

Set number of rings . . . . . . . . . . . . . . . . 28

Turn the call screening on or off . . . . . . . 28

Turn the message alert tone on or off. . . 28

Set the recording time . . . . . . . . . . . . . . 29

Using your built-in answering

system.......................29

Message playback . . . . . . . . . . . . . . . . . 29

Delete all messages . . . . . . . . . . . . . . . . 30

Remote access.................... 30

Set remote access code. . . . . . . . . . . . . 31

Call screening..................... 31

Call intercept...................... 32

Record, play, and delete memos . . . . . . 32

Retrieve voicemail from

telephone service . . . . . . . . . . . . . . 33

Retrieve voicemail . . . . . . . . . . . . . . . . . 33

Turn off the new voicemail indicators . . . 33

Expand your telephone system . . 33

Screen messages . . . . . . . . . . . . . . 34

Frequently asked questions . . . . . 36

General product care . . . . . . . . . . . 39

The RBRC® seal ...............39

FCC, ACTA and IC regulations . . . 40

California Energy Commission

battery charging testing

instructions...................42

For C-UL compliance only. . . . . . . 42

Limited warranty. . . . . . . . . . . . . . . 45

Technical specifications. . . . . . . . . . 47

1

What’s in the box

Your telephone package contains the following

items. Save your sales receipt and original

packaging in case it is necessary to ship your

telephone for warranty service.

NOTE

To purchase replacement batteries or power

adapters, visit our website at

www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial

1 (800) 267-7377.

1 set for CS6759

3 sets for CS6758-3/CS6759-3

Abridged user’s

manual

2 sets for CS6758-3/CS6759-3

1 set for CS6758-3/CS6759/CS6759-3

Important Safety

Instructions

2

Overview

Handset overview

1 – Handset earpiece

2 – LCD display

3 – MENU/SELECT

• Show the menu.

• While in a menu, press to select

an item, or save an entry or

setting.

4 – OFF/CANCEL

Hang up a call.

Silence the ringer temporarily

while the handset is ringing.

Press and hold to erase the

missed call indicator while the

phone is not in use.

Press to return to the previous

menu; or press and hold to return

to idle mode, without making

changes.

•

5 –

Press repeatedly to show other

dialing options when reviewing a

caller ID log entry.

6 – INT

Press to start an intercom

conversation or transfer a call (for

multi-handset models only).

7 – Microphone

8 –

• Make or answer a call using the

handset speakerphone.

• During a call, press to switch

between the speakerphone and

the handset.

9 – MUTE/DELETE

Mute the microphone during a

call.

Delete digits or characters while

using the dialing keys.

Silence the ringer temporarily

while the handset is ringing.

10 –

• While you have set the dial mode

to pulse and on a call, press to

switch to tone dialing temporarily.

11 –

Press to add a space when

entering names.

12 – 1

• Press repeatedly to add or

remove 1 in front of the caller ID

log entry before dialing or saving

it to the directory.

• Press and hold to set or dial your

voicemail number.

13 – /FLASH

• Make or answer a home call.

• Answer an incoming home call

when you hear a call waiting

alert.

•

a

b

c

d

e

f

g

h

i

j

n

p

o

k

l

m

3

14 – REDIAL/PAUSE

• Press repeatedly to review the

redial list.

• Press and hold to insert a dialing

pause while entering a number.

15 – VOLUME/ /

• Review the directory when the

phone is not in use.

• Increase the listening volume

during a call.

• Scroll up while in a menu, or in

the directory, caller ID log, or

redial list.

• Move the cursor to the right when

entering numbers or names.

VOLUME/ /CID

Review the caller ID log when the

phone is not in use.

Decrease the listening volume

during a call.

Scroll down while in a menu, or

in the directory, caller ID log, or

redial list.

Move the cursor to the left when

entering numbers or names.

16 – CHARGE light

• On when the handset is

charging.

•

Telephone base overview

1 – LCD display

2 – IN USE light

• Flashes when there is an

incoming call, or another

telephone sharing the same line

is in use.

• On when the handset is in use.

3 – MENU/SELECT

• Show the menu.

• While in a menu, press to select

an item, or save an entry or

setting.

FLASH

• Answer an incoming home call

when you hear a call waiting

alert.

• Review the directory when the

phone is not in use.

• Scroll up while in a menu, or in

the directory, caller ID log, or

redial list.

• Move the cursor to the right when

entering numbers or names.

CID

Review the caller ID log when

the phone is not in use.

Scroll down while in a menu, or

in the directory, caller ID log, or

redial list.

•

b

c

d

e

f

g

i

h

j

n

p

o

k

l

m

a

4

Move the cursor to the left when

entering numbers or names.

OFF/CANCEL

Press and hold to erase the

missed call indicator while the

phone is not in use.

Press to return to the previous

menu; or press and hold to return

to idle mode, without making

changes.

4 – /FIND HANDSET

• Press to page all system

handsets.

5 – ANS ON/OFF

• Press to turn the answering

system on or off.

6 – X/DELETE

• Press to delete the playing

message.

• When the phone is not in

use, press twice to delete all

previously reviewed messages.

/REPEAT

• Press to repeat the playing

message.

• Press twice to play the previous

message.

/SKIP

• Press to skip to the next

message.

/PLAY/STOP

• Press to play messages.

• Press to stop message playback.

7 – /SPEAKER

• Press to make or answer a call.

8 – MUTE

Mute the microphone during a

call.

Silence the ringer temporarily

while the handset is ringing.

•

9 –

Press repeatedly to show other

dialing options when reviewing a

caller ID log entry.

10 –

Press to add a space when

entering names.

11 –

• While you have set the dial mode

to pulse and on a call, press to

switch to tone dialing temporarily.

12 – MIC (Microphone)

13 – REDIAL/PAUSE

• Press repeatedly to review the

redial list.

• Press and hold to insert a dialing

pause while entering a number.

14 – Charging pole

15 – /VOL/

• Adjust the listening volume

during a call or message

playback.

• When the phone is not in use,

press to adjust the telephone

base ringer volume.

16 – INT

Press to start an intercom

conversation or transfer a call (for

multi-handset models only).

Charger overview

1 – Charging pole

•

a

5

Display icons overview

Handset icons

The battery icon flashes

when the battery is low and

needs charging.

The battery icon animates

when the battery is

charging.

The battery icon becomes

solid when the battery is

fully charged.

The handset ringer is off.

There are new voicemail

received from your

telephone service provider.

ECO The ECO mode activates

automatically to reduce

power consumption when

the handset is within range

from the telephone base.

NEW There are new caller ID log

entries.

Telephone base icons

The telephone base ringer

is turned off.

There are new voicemail

received from the telephone

service provider.

MSG #

1 The message number

currently playing, or the

total number of messages

recorded..

NEW The caller ID log entry you

are reviewing is new.

The message you are

listening is new.

Handset and Telephone base

lights overview

Handset lights

On when the handset

speakerphone is in use.

CHARGE On when the handset is

charging in the telephone

base or handset charger.

Telephone base lights

IN USE On when the telephone line

is in use.

On when you are

registering a handset.

Flashes quickly when there

is an incoming call.

Flashes when another

telephone sharing the same

line is in use.

Flashes when you are

deregistering all handsets.

ANS

ON/OFF

On when the answering

system is turned on.

MUTE On when the mute function

is turned on during a call.

/PLAY/

STOP

Flashes when there are

new messages or memos in

the answering system.

/

SPEAKER

On when the telephone

base speakerphone is in

use.

6

Connect

You can choose to connect the telephone

base for desktop usage or wall mounting.

NOTES

Use only the power adapters supplied with

this product.

Make sure the electrical outlets are not

controlled by wall switches.

The adapters are intended to be correctly

oriented in a vertical or ﬂoor mount

position. The prongs are not designed to

hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

TIP

If you subscribe to digital subscriber line

(DSL) high-speed Internet service through

your telephone line, make sure you install

a DSL filter (not included) between the

telephone line cord and telephone wall

jack. Contact your DSL service provider

for more information.

Connect the telephone base

•

Connect the charger

Mount the telephone base

1. Unplug the telephone line cord (or the

DSL ﬁlter) from the telephone wall

jack. Unplug the power adapter from

the electrical outlet. Slide the wall

mount bracket up and remove it from

the wall mount plate.

2. Press down on the tabs on the wall

mount bracket on the telephone base

to release it from tabletop orientation.

Rotate the wall mount bracket down

to wall mount position and then push

it into the telephone base until it

clicks into place.

7

Install and charge the battery

Install the battery as shown below.

NOTES

Use only supplied battery.

If the handset will not be used for a long

time, disconnect and remove the battery

to prevent possible leakage.

•

3. Plug the telephone line cord (or DSL

ﬁlter) into the wall jack. Align the

holes on the back of the telephone

base with the standard wall plate.

Slide the bracket down until it clicks

securely in place. Connect the power

adapter to the telephone base and

an electrical outlet not controlled by

a wall switch.

4. Slide the telephone base down until

it clicks securely in place. Bundle

the telephone line cord and power

adapter cord neatly with twist ties if

necessary.

8

Charge the battery

Place the handset in the telephone base

or the charger to charge.

Once you have installed the battery,

the handset LCD display indicates the

battery status (see the table below).

NOTES

For best performance, keep the handset in

the telephone base or charger when not

in use.

The battery is fully charged after 12 hours

of continuous charging.

If you place the handset in the telephone

base or the charger without plugging

in the battery, the screen displays

No battery.

Battery

indicators

Battery

status

Action

The screen

is blank, or

shows Put

in charger

and

ﬂashes.

The battery

has no

charge or

very little

charge. The

handset

cannot be

used.

Charge

without

interruption

(at least 30

minutes).

The screen

shows Low

battery and

ﬂashes.

The battery

has enough

charge to be

used for a

short time.

Charge

without

interruption

(at least 30

minutes).

The screen

shows

HANDSET X.

The battery is

charged. To keep

the battery

charged,

place it in the

telephone

base or

charger when

not in use.

•

When it is fully charged, you can expect the

following performance:

Operation Operating time

While in handset

use (talking*) Seven hours

While in

speakerphone

mode (talking*)

Three hours and 30

minutes

While not in use

(standby**) Five days

* Operating times vary depending on your actual

use and the age of the battery.

** Handset is not charging or in use.

9

Before use

After you install your telephone or

power returns following a power outage,

the handset will prompt you to set the

date and time.

Set date and time

NOTE

Make sure you set the date and time

including the year correctly; otherwise the

answering system does not announce the

correct day of the week for your recorded

messages time stamp.

Use the dialing keys (0-9) to enter

the month (MM), date (DD) and year

(YY). Then press SELECT.

2. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press or to choose AM or PM.

3. Press SELECT to save.

Check for dial tone

Press . If you hear a dial tone, the

installation is successful.

If you do not hear a dial tone:

Make sure the installation procedures

described above are properly done.

It may be a wiring problem. If you

have changed your telephone

service to digital service from a

cable company or a VoIP service

provider, the telephone line may need

to be rewired to allow all existing

telephone jacks to work. Contact your

cable/VoIP service provider for more

information.

•

1.

•

Operating range

This cordless telephone operates with

the maximum power allowed by the

Federal Communications Commission

(FCC). Even so, this handset and

telephone base can communicate over

only a certain distance - which can

vary with the locations of the telephone

base and handset, the weather, and the

layout of your home or ofﬁce.

When the handset is out of range, the

handset displays Out of range or no pwr

at base.

If there is a call while the handset is

out of range, it may not ring, or if it

does ring, the call may not connect well

when you press . Move closer to the

telephone base, and then press

to answer the call. If the handset

moves out of range during a telephone

conversation, there may be interference.

To improve reception, move closer to the

telephone base.

10

Configure your telephone

Press MENU when the phone is not

in use.

Press or until the screen displays

the desired feature menu.

Press SELECT to enter that menu.

To return to the previous menu, press

CANCEL on the handset.

To return to idle mode, press and hold

CANCEL on the handset.

Set language

The LCD language is preset to English.

You can select English, French or

Spanish to be used in all screen displays.

Press MENU when the handset is not

in use.

Press or to highlight Settings,

and then press SELECT.

Press SELECT to select

LCD language.

Press or to highlight English,

Français or Español, and then press

SELECT.

The screen displays Set English?

when you choose English.

The screen displays Set Français?

when you choose Français.

The screen displays Set Español?

when you choose Español.

5. Press SELECT to save your

selection. You hear a conﬁrmation

tone

NOTE

If you accidentally changed the LCD

language to French or Spanish, you can

reset it to English easily by pressing MENU

and then entering 364 .

1.

2.

3.

•

1.

2.

3.

4.

•

Set date and time

NOTE

Make sure you set the date and time

including the year correctly; otherwise the

answering system does not announce the

correct day of the week for your recorded

messages time stamp.

Press MENU when the handset is not

in use.

Press or to highlight Set date/time,

and then press SELECT.

Use the dialing keys (0-9) to enter

the month (MM), date (DD) and year

(YY). Then press SELECT.

4. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press or to choose AM or PM.

5. Press SELECT to save.

•

1.

2.

3.

11

Home area code

If you dial your local calls using only

seven digits (area code not required),

you can program your home area code

so that when you receive a call within

your local area, the telephone number

is automatically stored without the area

code in the caller ID log.

Press MENU when the phone is not

in use.

Press or to highlight Settings,

and then press SELECT.

Press or to highlight Home area

code, and then press SELECT.

Use the dialing keys to enter a

three-digit home area code.

Press SELECT to save your

selection. Then the handset returns

to the previous menu. You hear a

conﬁrmation tone.

NOTE

If, in the future, your telephone service

provider requires you to dial the area code

when making a local call, or, if you move to

a location that requires it, delete the home

area code you have already programmed,

following the steps above. After you have

deleted the home area code, _ _ _ will

appear on the display.

1.

2.

3.

4.

5.

Dial mode

The dial mode is preset to touch-tone

dialing. If you have pulse (rotary)

service, you must change the dial

mode to pulse dialing before using the

telephone to make a call.

Press MENU when the phone is not

in use.

Press or to highlight Settings,

and then press SELECT.

Press or to highlight Dial mode,

and then press SELECT.

Press or to choose Touch-tone

or Pulse.

Press SELECT to save your

selection. Then the handset returns

to the previous menu. You hear a

conﬁrmation tone.

Temporary tone dialing

If you have pulse (rotary) service only,

you can switch from pulse to touch-tone

dialing temporarily during a call. This

is useful if you need to send touch-

tone signals to access your telephone

banking or long distance services.

During a call, press .

Use the dialing keys to enter the

number you wish to dial.

The telephone sends touch-tone

signals. The telephone automatically

returns to pulse dialing mode after

you end the call.

1.

2.

3.

4.

5.

1.

2.

3.

12

Telephone Operations Make a call

Press or on the handset.on the handset.

When you hear a dial tone, dial the

number.

The handset displays Unable to

call if the telephone line is in use.

NOTES

The handset shows the elapsed time as

you talk (in hours, minutes and seconds).

While entering numbers, press and hold

PAUSE to insert a dialing pause

(a p appears).

Predial a call

Enter the telephone number.

Press or to dial.to dial.

NOTES

The handset displays Unable to call if

the telephone line is in use.

The handset shows the elapsed time as

you talk (in hours, minutes and seconds).

While entering numbers, press DELETE

or CANCEL to make corrections;

press and hold PAUSE to insert a dialing

pause (a p appears).

Answer a call

Press , , or any dialing key (0-9,

, or ) to answer.

End a call

Press OFF on the handset, or place the

handset in the telephone base or

handset charger.

Speakerphone

When the handset is on a call, press

to switch between the speakerphone

and the handset earpiece. When the

speakerphone is active, the handset

displays Speaker.

1.

2.

•

1.

2.

•

Handset control key panel:

13

Volume control

To adjust the listening volume at

the handset:

During a call, press /VOLUME/ .

To adjust the listening volume at

the telephone base:

During a call, press /VOL/ to adjust

the listening volume.

NOTES

The handset and speakerphone volume

settings are independent.

When the volume reaches the minimum

or maximum setting, you hear two beeps.

Mute

The mute function allows you to hear

the other party but the other party

cannot hear you.

During a call, press MUTE. The

handset displays Muted until the

mute function is turned off.

Press MUTE again to resume the

conversation. The handset briefly

displays Microphone on.

Join a call in progress (for

multiple handset models only)

Another handset can join you on a

home call. That call continues until

all parties hang up. You can share an

outside call with up to two handsets at

the same time.

You can buy additional expansion

handsets (CS6709) for this telephone

base. You can register up to ﬁve devices

to the telephone base.

•

To join a call::

When a handset is already on a call,

press or on another handset to

join the call.

Press OFF or place the handset

in the telephone base or handset

charger to exit the call. The call

continues on the other handset until

both handsets hang up.

Call waiting

When you subscribe to call waiting

service with your telephone service

provider, the handset ﬂashes and you

hear a beep if someone calls while you

are already on a call.

Press FLASH on the handset to put

your current call on hold and take the

new call.

Press FLASH on the handset at any

time to switch back and forth

between calls.

Chain dialing

Use this feature to initiate a dialing

sequence from numbers stored in the

directory, caller ID log or redial list while

you are on a call.

Chain dialing can be useful if you wish

to access other numbers (such as bank

account numbers or access codes)

from the directory, caller ID log or

redial list.

To access a number from the

directory while on a call:

Press MENU.

Press SELECT to select Directory.

Press or to scroll to the desired

entry.

Press SELECT to dial the displayed

number.

•

1.

2.

3.

4.

14

To access a number from the

caller ID log while on a call:

Press MENU.

Press or to highlight Caller ID

log, and then press SELECT.

Press or to scroll to the desired

entry.

Press SELECT to dial the displayed

number.

To access a number from the

redial list while on a call:

Press REDIAL to enter the redial list.

Press , , or REDIAL repeatedly to

browse to the desired entry.

Press SELECT to dial the displayed

number.

Find handset

This feature helps you ﬁnd misplaced

handsets.

To start the paging tone:

Press /FIND HANDSET on the

telephone base.

All idle handsets ring and their

screens display ** Paging **.

To stop the paging tone:

Press , OFF, or any dialing key

(0-9, , or ) on a handset.

1.

2.

3.

4.

1.

2.

3.

•

Transfer a call

While on an outside call, you can

transfer the call from one handset to

another.

During a call, press MENU.

Press or to scroll to Transfer,

then press SELECT.

If you have one handset, your

handset displays Calling base and

then Transferred.

If you have two or more handsets,

your handset displays Transfer to:

Press 7 for the telephone base or

1-5 for HANDSET 1 or

HANDSET 5. Your handset

displays Calling base or Calling

HS X and then Transferred.

The destination device rings and its

screen displays Incoming call.

3. To answer on the destination device,

press , , or any dialing key

(0-9, , or ) on the destination

handset, or press /SPEAKER or

any dialing key (0-9, , or ) on

the telephone base.

NOTES

If the destination device does not answer

the call within 30 seconds, the call will

be reverted to the originating handset. If

you do not press , , or any dialing

key (0-9, , or ) on your handset

to reconnect the outside call within 30

seconds, the call ends automatically.

If the destination device is in the directory

or caller ID log, or is out of range, the

originating handset displays Unable to

call and then reconnects to the outside

call.

1.

2.

•

La page charge ...

VTech CS6759 Manuel utilisateur

VTech CS6759 Manuel utilisateur

dans d''autres langues

Documents connexes