VTech CS5229-3 Manuel utilisateur

Marque: VTech

Modèle: CS5229-3

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

5229

5229-2

5229-3

5229-4

5229-5

Click on the in the manual

to watch the video tutorials.

User’s manual

Scan the QR code to go and

subscribe our tutorial channel

Congratulations

on purchasing your new VTech product. Before

using this telephone, please read Important safety

instructions.

This manual has all the feature operations and

troubleshooting necessary to install and operate your

new VTech telephone. Please review this manual

thoroughly to ensure proper installation and operation

of this innovative and feature rich VTech product.

For support, shopping, and everything new at

VTech, visit our website at www.vtechphones.com. In

Canada, please visit phones.vtechcanada.com.

Compatible with

Hearing Aid T-Coil

TIA-1083

Telephones identiﬁed

with this logo have

reduced noise and

interference when

used with most T-coil

equipped hearing aids

and cochlear implants.

The TIA-1083 Compliant

Logo is a trademark of

the Telecommunications

Industry Association.

Used under license.

The ENERGY STAR®

program (www.

energystar.gov)

recognizes and

encourages the use

of products that save

energy and help protect

our environment. We

are proud to mark

this product with the

ENERGY STAR® label

indicating it meets the

latest energy efﬁciency

guidelines.

Important safety instructions

When using your telephone equipment, basic safety

precautions should always be followed to reduce the

risk of ﬁre, electric shock and injury, including the

following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on

the product.

3. Unplug this product from the wall outlet before

cleaning. Do not use liquid or aerosol cleaners.

Use a damp cloth for cleaning.

4. CAUTION: Do not install the telephone base at a

height above 2 meters.

5. Do not use this product near water such as near a

bath tub, wash bowl, kitchen sink, laundry tub or a

swimming pool, or in a wet basement or shower.

6. Do not place this product on an unstable table,

shelf, stand or other unstable surfaces.

7. Avoid placing the telephone system in places

with extreme temperature, direct sunlight, or

other electrical devices. Protect your phone from

moisture, dust, corrosive liquids and fumes.

8. Slots and openings in the back or bottom of the

telephone base and handset are provided for

ventilation. To protect them from overheating,

these openings must not be blocked by placing

the product on a soft surface such as a bed, sofa

or rug. This product should never be placed near

or over a radiator or heat register. This product

should not be placed in any area where proper

ventilation is not provided.

9. This product should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supply in your home or ofﬁce, consult your dealer

or local power company.

10. Do not allow anything to rest on the power cord.

Do not install this product where the cord may be

walked on.

11. Never push objects of any kind into this product

through the slots in the telephone base or handset

because they may touch dangerous voltage

points or create a short circuit. Never spill liquid of

any kind on the product.

12. To reduce the risk of electric shock, do not

disassemble this product, but take it to an

authorized service facility. Opening or removing

parts of the telephone base or handset other

than speciﬁed access doors may expose you

to dangerous voltages or other risks. Incorrect

reassembling can cause electric shock when the

product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer

servicing to an authorized service facility under

the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or

water.

• If the product does not operate normally by

following the operating instructions. Adjust

only those controls that are covered by the

operation instructions. Improper adjustment

of other controls may result in damage and

often requires extensive work by an authorized

technician to restore the product to normal

operation.

• If the product has been dropped and the

telephone base and/or handset has been

damaged.

• If the product exhibits a distinct change in

performance.

15. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote risk

of electric shock from lightning.

16. Do not use the telephone to report a gas leak in the

vicinity of the leak. Under certain circumstances,

a spark may be created when the adapter is

plugged into the power outlet, or when the

handset is replaced in its cradle. This is a common

event associated with the closing of any electrical

circuit. The user should not plug the phone into

a power outlet, and should not put a charged

handset into the cradle, if the phone is located

in an environment containing concentrations of

ﬂammable or ﬂame-supporting gases, unless

there is adequate ventilation. A spark in such an

environment could create a ﬁre or explosion.

Such environments might include: medical use of

oxygen without adequate ventilation; industrial

gases (cleaning solvents; gasoline vapors; etc.); a

leak of natural gas; etc.

17. Only put the handset of your telephone next to

your ear when it is in normal talk mode.

18. The power adapter is intended to be correctly

oriented in a vertical or ﬂoor mount position. The

prongs are not designed to hold the plug in place

if it is plugged into a ceiling, under-the-table or

cabinet outlet.

19. For pluggable equipment, the socket outlet shall

be installed near the equipment and shall be

easily accessible.

20. CAUTION: Use only the batteries

indicated in this manual. There may be a risk of

explosion if a wrong type of battery is used for

the handset. Use only the supplied rechargeable

batteries or replacement batteries (BT162342/

BT262342) for the handset. Do not dispose of

batteries in a ﬁre. They may explode. Disposed of

used batteries according to the instruction.

• Do not use the battery in following

conditions:

»High or low extreme temperature during

use, storage or transportation.

»Replacement of a battery with an incorrect

type that can defeat a safeguard.

»Disposal of a battery into ﬁre or a hot oven,

or mechanically crushing or cutting of a

battery, that can result in an explosion.

»Leaving a battery in an extremely high tem-

perature surrounding environment that

can result in an explosion or the leakage of

ﬂammable liquid or gas.

»A battery subjected to extremely low air

pressure that can result in an explosion or

the leakage of ﬂammable liquid or gas.

21. Use only the adapter included with this product.

Incorrect adapter polarity or voltage can seriously

damage the product.

22. The applied nameplate is located at the bottom or

near of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent.

To order a replacement, visit our website at

www.vtechphones.com or call 1 (800) 595-9511.

In Canada, go to phones.vtechcanada.com or call

1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for special

disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns or

injury to the eyes or skin. The electrolyte may be

toxic if swallowed.

• Exercise care in handling batteries in order not to

create a short circuit with conductive materials.

• Charge the battery provided with this product

only in accordance with the instructions and

limitations speciﬁed in this manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital cordless

telephones):

Wireless Technology Research, LLC (WTR), an

independent research entity, led a multidisciplinary

evaluation of the interference between portable

wireless telephones and implanted cardiac

pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches

from the pacemaker.

• Should NOT place wireless telephones directly over

the pacemaker, such as in a breast pocket, when it is

turned ON.

• Should use the wireless telephone at the ear opposite

the pacemaker.

WTR’s evaluation did not identify any risk to bystanders

with pacemakers from other persons using wireless

telephones.

About cordless telephones

• Privacy: The same features that make a cordless

telephone convenient create some limitations.

Telephone calls are transmitted between the

telephone base and the cordless handset by radio

waves, so there is a possibility that the cordless

telephone conversations could be intercepted

by radio receiving equipment within range of

the cordless handset. For this reason, you should

not think of cordless telephone conversations as

being as private as those on corded telephones.

• Electrical power: The telephone base of this

cordless telephone must be connected to a

working electrical outlet. The electrical outlet

should not be controlled by a wall switch. Calls

cannot be made from the cordless handset if the

telephone base is unplugged, switched off or if

the electrical power is interrupted.

• Potential TV interference: Some cordless

telephones operate at frequencies that may cause

interference to televisions and VCRs. To minimize

or prevent such interference, do not place

the telephone base of the cordless telephone

near or on top of a TV or VCR. If interference is

experienced, moving the cordless telephone

farther away from the TV or VCR often reduces or

eliminates the interference.

• Rechargeable batteries: Exercise care in handling

batteries in order not to create a short circuit with

conducting material such as rings, bracelets and

keys. The battery or conductor may overheat and

cause harm. Observe proper polarity between

the battery and the battery charger.

• Nickel-metal hydride rechargeable batteries:

Dispose of these batteries in a safe manner. Do not

burn or puncture the battery. Like other batteries

of this type, if burned or punctured, they could

release caustic material which could cause injury.

ECO mode

This power conserving technology reduces power

consumption for optimal battery performance. The

ECO mode activities automatically whenever the

handset is synchronized with the telephone base.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures

corporelles ou d’électrocution, suivez toujours ces

mesures préventives de base lorsque vous utilisez

votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde

inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale

avant de le nettoyer. N’utilisez pas de nettoyeurs

liquides ni en aérosol. N’utilisez qu’un chiffon

doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique

à une hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près

d’un bain, d’un lavabo, d’un évier de cuisine, d’un

bac de lavage ou d’une piscine, ou dans un sous-

sol humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un chariot,

support ou table chancelants. L’appareil pourrait

tomber et être sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans

les endroits soumis à une température extrême,

à la lumière directe du soleil ou à proximité

immédiate d’autres appareils électriques ou

électroniques. Protégez votre téléphone contre

les sources d’humidité, la poussière, les vapeurs

et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et

d’ouvertures d’aération situées à l’arrière ou

en dessous. Aﬁn d’empêcher la surchauffe, ces

ouvertures ne doivent pas être obstruées en

plaçant l’appareil sur un lit, divan, tapis ou autre

surface similaires. Ne placez pas cet appareil

proximité d’un élément de chauffage ni d’une

plinthe électrique. De plus, ne l’installez pas dans

une unité murale ou un cabinet fermé qui ne

possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le

type d’alimentation indiqué sur les étiquettes de

l’appareil. Si vous ne connaissez pas le voltage de

votre maison, consultez votre marchand ou votre

fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation.

Installez cet appareil dans un endroit sécuritaire,

là où personne ne pourra trébucher sur la

ligne d’alimentation ni le cordon téléphonique

modulaire.

11. N’insérez jamais d’objets à travers les fentes et

ouvertures de cet appareil, car ils pourraient

toucher à des points de tension dangereux ou

court-circuiter des pièces, ce qui constituerait un

risque d’incendie ou d’électrocution. N’échappez

pas de liquides dans l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne

démontez pas l’appareil, mais apportez-le plutôt

à un centre de service qualiﬁé s’il doit être réparé.

En enlevant le couvercle, vous vous exposez à

des tensions dangereuses ou autres dangers

similaires. Un remontage inadéquat peut être à

l’origine d’une électrocution lors d’une utilisation

ultérieure de l’appareil. Débranchez l’appareil

avant de procéder au nettoyage. Utilisez un

chiffon humide et doux.

13. Ne surchargez pas les prises de courant et les

rallonges.

14. Débranchez cet appareil de la prise de courant et

communiquez avec le département de service à

la clientèle de VTech dans les cas suivants:

• Lorsque le cordon d’alimentation est

endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé une source

d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement

en respectant les instructions de

fonctionnement. Réglez uniquement les

commandes indiquées dans le les instructions

de fonctionnement. Les réglages incorrects

des autres commandes pourraient provoquer

un dommage qui pourrait exiger un travail

exhaustif de la part d’un technicien autorisé

aﬁn de rétablir le fonctionnement normal de

l’appareil.

• Si le produit a été échappé et que le socle et/

ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de

sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans

ﬁl) pendant un orage. Les éclairs peuvent être à

l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une

fuite de gaz à proximité de la fuite. En certaines

circonstances, une ﬂammèche pourrait être

provoquée lorsque l’adaptateur est branché à une

prise de courant, ou lorsque le combiné est déposé

sur le socle. Ceci est un événement commun

associé à la fermeture d’un circuit électrique.

L’utilisateur ne devrait pas brancher le téléphone

à une prise de courant, et ne devrait pas déposer

le combiné chargé sur le socle, si le téléphone se

trouve à proximité d’un endroit comportant des

concentrations de gaz inﬂammables, moins que

la ventilation soit adéquate. Une ﬂammèche dans

un tel endroit pourrait provoquer un incendie ou

une explosion. De tels environnements peuvent

comprendre: des endroits où l’on utilise de

l’oxygène médical sans ventilation adéquate; des

gaz industriels (dissolvants de nettoyage, des

vapeurs d’essence, etc.); une fuite de gaz naturel,

etc.

17. Ne placez que le combiné de votre téléphone près

de votre oreille lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour être orientés

en position verticale ou montés au sol. Les broches

ne sont pas conçues pour maintenir l’adaptateur

en place si celui-ci est barnché dans une prise au

plafond ou sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE

COURANT, le socle de prise de courant doit

etre installe a proximite du materiel et doit etre

aisement accessible.

20. MISE EN GARDE: Il peut y avoir un

risque d’explosion si vous utilisez le mauvais

type de piles pour le téléphone. N’utilisez que

les piles rechargeable inclus ou les piles de

rechange (BT162342/BT262342). N’incinérez pas

les piles. Celles-ci risqueraient d’exploser. Mettre

au rebut les batteries usagées conformément aux

instructions du fabricant. Débrancher les lignes

téléphoniques avant le remplacement des piles.

• Évite d’utiliser la batterie dans les conditions

suivantes:

»des températures extrêmes faibles ou

élevées auxquelles une batterie peut être

soumise pendant l’utilisation, le stockage

ou le transport.

»remplacement d’une batterie par un type

incorrect pouvant supprimer une protec-

tion.

»mise au rebut d’une batterie dans un feu

ou dans un four chaud, ou écrasement mé-

canique ou coupure d’une batterie, sus-

ceptible de provoquer une explosion.

»maintien d’une batterie dans un environne-

ment à très haute température pouvant

provoquer une explosion ou la fuite de liq-

uide ou de gaz inﬂammables.

»batterie soumise à une pression de l’air ex-

trêmement faible pouvant provoquer une

explosion ou la fuite de liquide ou de gaz

inﬂammables.

21. N’utilisez que les adaptateurs inclus avec ce

produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque

d’endommager sérieusement le produit et mettre

votre sécurité en péril.

22. La plaque signalétique appliquée est située au

bas ou à proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

Pour commander une pile de recharge, visitez

notre site Web au www.vtechphones.com ou

composez le 800-595-9511. Au Canada, visitez le

phones.vtechcanada.com ou composez le 800-

267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les instructions

spéciﬁques de mise aux rebus auprès des autorités

locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte

qui s’en échapperait est corrosif et pourrait causer

des brûlures ou des blessures aux yeux ou à la

peau. L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles

aﬁn d’éviter les courts-circuits provoqués par des

matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon

les instructions et limites spéciﬁées dans ce guide

d’utilisation.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (s’applique uniquement

aux téléphones numériques sans ﬁl):

L’organisme ‘Wireless Technology Research, LLC

(WTR)’, une ﬁrme de recherche indépendante, a mené

une évaluation pluridisciplinaire des interférences

entre les téléphones sans ﬁl portatifs et les stimulateurs

cardiaques implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues (FDA) des

États-Unis, la ﬁrme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs

cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance

d’au moins six pouces du stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl

directement sur le stimulateur cardiaque, tel que

dans une poche de chemise, lorsque celui-ci est

en marche.

• Ils doivent utiliser le téléphone sans ﬁl en

l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas

identiﬁé de risque pour les détenteurs de simulateurs

cardiaques causés par les gens qui utilisent un

téléphone sans ﬁl à proximité de ceux-ci.

À propos des téléphones sans ﬁl

• Alimentation électrique: Les mêmes

caractéristiques qui constituent des avantages

pour les téléphones sans ﬁl afﬁchent également

des restrictions. Les appels téléphoniques sont

transmis entre le combiné sans ﬁl et le socle par le

biais d’ondes radio ; il y a donc la possibilité que

vos conversations téléphoniques sans ﬁl soient

interceptées par des équipements de réception

radio se trouvant dans la portée du combiné sans

ﬁl. Pour cette raison, vous ne devez pas percevoir

les communications téléphoniques sans ﬁl comme

étant aussi conﬁdentielles.

• Alimentation électrique: Le socle de ce téléphone

sans ﬁl doit être branché à une prise électrique

fonctionnelle. La prise électrique ne doit pas être

contrôlée par un interrupteur mural. Les appels ne

pourront pas être effectués du combiné sans ﬁl si

le socle est débranché ou mis hors tension ou si le

courant est coupé.

• Possibilité d’interférences aux téléviseurs:

Certains téléphones sans ﬁl fonctionnent sur des

fréquences pouvant causer des interférences aux

téléviseurs et aux magnétoscopes. Pour réduire

ou prévenir de telles interférences, ne placez

pas le socle du téléphone sans ﬁl près ou sur un

téléviseur ou magnétoscope. S’il y a présence de

parasites, il est conseillé d’éloigner le téléphone

sans ﬁl du téléviseur ou du magnétoscope aﬁn de

réduire possiblement les interférences.

• Piles rechargeables: Manipulez les piles avec soin

aﬁn de ne pas les court-circuiter avec des bagues,

bracelets ou clés. Les piles ou le conducteur peut

surchauffer et causer des blessures. Respectez la

polarité adéquate entre la pile et le chargeur.

• Les bloc-piles rechargeables à l’hydrure

métallique de nickel: Jetez ces blocs-piles de

manière écologique et sécuritaire. Ne les incinérez

pas et ne les percez pas. Tel que les autres piles

de ce type, elles pourraient dégager une matière

toxique qui peut causer des blessures corporelles

si elles sont brûlées ou percées.

The RBRC seal

The RBRC seal on the nickel-metal hydride battery

indicates that VTech Communications, Inc. is voluntarily

participating in an industry program to collect and

recycle these batteries at the end of their useful lives,

when taken out of service within the United States and

Canada.

The program provides a convenient alternative to

placing used nickel-metal hydride batteries into the

trash or municipal waste, which may be illegal in your

area.

VTech’s participation makes it easy for you to drop

off the spent battery at local retailers participating in

the program or at authorized VTech product service

centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery

recycling and disposal bans/restrictions in your area.

VTech’s involvement in this program is part of its

commitment to protecting our environment and

conserving natural resources.

The RBRC seal and 1 (800) 8 BATTERY® are registered

trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

This equipment has been tested and found to

comply with the requirements for a Class B digital

device under Part 15 of the Federal Communications

Commission (FCC) rules. These requirements are

intended to provide reasonable protection against

harmful interference in a residential installation. This

equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However,

there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause

harmful interference to radio or television reception,

which can be determined by turning the equipment

off and on, the user is encouraged to try to correct

the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for

compliance could void the user’s authority to operate

the equipment.

This device complies with Part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received,

including interference that may cause undesired

operation. Privacy of communications may not be

ensured when using this telephone.

To ensure safety of users, the FCC/ISEDC has

established criteria for the amount of radio frequency

energy that can be safely absorbed by a user or

bystander according to the intended usage of the

product. This product has been tested and found

to comply with the FCC/ISEDC criteria. The handset

may be safely held against the ear of the user. The

telephone base shall be installed and used such that

parts of the user’s body other than the hands are

maintained at a distance of approximately 20 cm (8

inches) or more.

This Class B digital apparatus complies with Canadian

requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC

rules and with technical requirements adopted by

the Administrative Council for Terminal Attachments

(ACTA). The label on the back or bottom of this

equipment contains, among other things, a product

identiﬁer in the format US:AAAEQ##TXXXX. This

identiﬁer must be provided to your telephone service

provider upon request.

The plug and jack used to connect this equipment

to premises wiring and the telephone network must

comply with applicable Part 68 rules and technical

requirements adopted by ACTA. A compliant

telephone cord and modular plug is provided with

this product. It is designed to be connected to a

compatible modular jack that is also compliant. An

RJ11 jack should normally be used for connecting to

a single line and an RJ14 jack for two lines. See the

installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to

determine how many devices you may connect to

your telephone line and still have them ring when

you are called. The REN for this product is encoded

as the 6th and 7th characters following the US: in the

product identiﬁer (e.g., if ## is 03, the REN is 0.3). In

most, but not all areas, the sum of all RENs should be

ﬁve (5.0) or less. For more information, please contact

your telephone service provider.

This equipment may not be used with Party Lines. If

you have specially wired alarm dialing equipment

connected to your telephone line, ensure the

connection of this equipment does not disable your

alarm equipment. If you have questions about what

will disable alarm equipment, consult your telephone

service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be

unplugged from the modular jack until the problem

has been corrected. Replacement to this telephone

equipment can only be made by the manufacturer or

its authorized agents. For replacement procedures,

follow the instructions outlined under the “Limited

warranty”.

If this equipment is causing harm to the telephone

network, the telephone service provider may

temporarily discontinue your telephone service. The

telephone service provider is required to notify you

before interrupting service. If advance notice is not

practical, you will be notiﬁed as soon as possible. You

will be given the opportunity to correct the problem

and the telephone service provider is required to

inform you of your right to ﬁle a complaint with the

FCC. Your telephone service provider may make

changes in its facilities, equipment, operation, or

procedures that could affect the proper functioning

of this product. The telephone service provider is

required to notify you if such changes are planned.

If this product is equipped with a corded or cordless

handset, it is hearing aid compatible.

If this product has memory dialing locations, you may

choose to store emergency telephone numbers (e.g.,

police, ﬁre, medical) in these locations. If you do store

or test emergency numbers, please:

Remain on the line and brieﬂy explain the reason for

the call before hanging up.

Perform such activities in off-peak hours, such as early

morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and

Economic Development Canada’s licence-exempt

RSS(s).

Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2)

this device must accept any interference, including

interference that may cause undesired operation.

Privacy of communications may not be ensured when

using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration

number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this

terminal equipment is 0.1. The REN is an indication

of the maximum number of devices allowed to be

connected to a telephone interface. The termination

on an interface may consist of any combination of

devices subject only to the requirement that the sum

of the RENs of all the devices does not exceed ﬁve.

This product meets the applicable Innovation, Science

and Economic Development Canada technical

speciﬁcations.

California Energy Commission battery

charging testing instructions

This telephone is set up to comply with the energy-

conserving standards right out of the box. These

instructions are intended for California Energy

Commission (CEC) compliance testing only. When the

CEC battery charging testing mode is activated, all

telephone functions, except battery charging, will be

disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the

power outlet. Make sure all handsets are plugged

with charged batteries before proceeding.

2. While you press and hold /FIND HS, plug the

telephone base power adapter back to the power

outlet.

3. After about 20 seconds, when the IN USE light starts

ﬂashing, release /FIND HS and immediately

press it again within two seconds.

When the phone successfully enters the CEC battery

charging testing mode, all handsets display To register

HS, see manual.

When the phone fails to enter this mode, repeat steps

1 to 3 above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from

the power outlet, then plug it back in. Then the

telephone base is powered up as normal.

2. Put the handset you wish to register on the

telephone base cradle.

3. The handset shows Registering... Please wait and

the IN USE light on the telephone base turns on.

The handset beeps and the IN USE light turns off

when the registration process completes.

Contents

Install | Set up 14

What’s in the box 14

Connect the telephone base 15

Connect the charger 15

Install the battery 16

Charge the battery 16

Check the battery level 17

Check for dial tone 17

Before use 18

Set date and time (before use) 18

Set up through voice guide -

Answering system (before use) 18

Install 19

Mount the telephone base 19

Overview 20

Telephone base 20

Handset 21

Display 23

Handset lights 23

Telephone base lights 24

Operating range 24

Operate 25

Make, answer or end a call 25

Make a call 25

Predial a call 25

Answer a call 25

End a call 25

View dialing options 25

Sound 26

Use speakerphone 26

Volume control 26

Mute the microphone 26

Temporary ringer silencing 26

Join a call 27

Join a call in progress (for multiple

handset models only) 27

Transfer a call 27

Blind transfer (for multiple handset

models only) 27

Call waiting 28

Intercom 28

Initiate an intercom call 28

Answer an incoming call during an

intercom call 29

Transfer a call via intercom 29

Find handset 30

Page/ ﬁnd handset 30

Use phone menu 31

Phonebook | Phonebook entry 31

Add a phonebook entry 31

Review the phonebook entries 32

Dial a phonebook entry 32

Delete a phonebook entry 33

Edit a phonebook entry 33

Alphabetical search 34

Redial list 35

Review a redial list entry 35

Dial a redial list entry 35

Save a redial entry to the

phonebook 35

Delete a redial list entry 36

Chain dialing 36

Caller ID 37

Review the caller ID log 37

Save a caller ID log entry to the

phonebook 38

Save a caller ID log entry to call

block list 39

Dial a caller ID log entry 39

Delete caller ID log entries 39

Caller ID memory match 40

Missed call indicator 40

Call block 41

Block unknown calls 41

Add a call block list entry 41

Review call block list 42

Edit a call block list entry 42

Save a caller ID log entry to the call

block list 42

Unblock a telephone number 42

Mute ﬁrst ring 43

Answering system 43

Difference between the built-in

answering system and voicemail

service 43

Use your built-in answering system

Turn on or off the answering system

Playback messages 45

Adjust listening volume during

message playback 47

Skip to the next message 47

Repeat the playing message 47

Listen to the previous message 47

Stop the message playback 47

Delete a message 47

Delete all messages 48

Answering system remote access 49

Call intercept while using answering

system 49

Recording memo 50

Turn on or off the call screening 50

Screen a call with answering system

Contents

Announcement 51

Record a new outgoing

announcement 51

Play your announcement 52

Delete your annoucement 52

Voicemail (via Tlephone service

provider) 53

Turn off the new voicemail

indicators 53

Conﬁgure | Settings 54

Answering system settings 54

Set your built-in answering system

Set answering system through voice

guide 54

Set remote access code 55

Turn on or off the message alert

tone 55

Set message recording time 56

Dial modes 56

Temporary tone dialing 56

Set dial mode 57

Ringer 57

Set ringer tone 57

Set ringer volume 58

Set date and time 58

Set languages 59

Set LCD language 59

Set voice language 59

Sound settings 60

Set number of rings 60

Set QUIET mode 60

Set listening volume 61

Set key tone 61

Voicemail settings 61

Set speed dial voicemail number 61

General product care 63

Taking care of your telephone 63

Avoid rough treatment 63

Avoid water 63

Electrical storms 63

Cleaning your telephone 63

Technical speciﬁcations 64

DECT 6.0 digital technology 64

Telephone operating range 64

Redeﬁning long range coverage

and clarity 64

Simulated full-duplex handset

and base speakerphones 65

Frequently asked questions 65

14 15

Install | Set up

What’s in the box

Your telephone package contains the

following items. Save your sales receipt

and original packaging in case it is

necessary to ship your telephone for

warranty service.

NOTE

• To purchase replacement batteries

or power adapters, visit our website

at www.vtechphones.com or call

1 (800) 595-9511. In Canada, go to

phones.vtechcanada.com or dial

1 (800) 267-7377.

Quick

start

guide

• 1 set for

CS5229

• 2 sets for

CS5229-2

• 3 sets for

CS5229-3

• 4 sets for

CS5229-4

• 5 sets for

CS5229-5

• 1 set for

CS5229-2

• 2 sets for

CS5229-3

• 3 sets for

CS5229-4

• 4 sets for

CS5229-5

Connect the telephone base

TIPS

• If you want to mount the base, make

sure telephone line pass through the

mounting bracket before connecting

to the DSL ﬁlter.

• If you subscribe to digital subscriber

line (DSL) high-speed Internet

service through your telephone line,

make sure you connect a DSL ﬁlter

(not included) to the telephone wall

jack.

Connect the charger

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1951

12 hrs

16 17

Install the battery

1. Plug the battery connector securely

into the socket inside the handset

battery compartiment.

• Make sure the battery label THIS

SIDE UP is facing up, as indicated.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1535

THIS SIDE UP

2. Align the cover ﬂat against the battery

compartment, then slide it upwards

until it clicks into place.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V 400mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1535

Charge the battery

The following table summarizes th

battery indicators and actions to take.

Battery

indicators

Battery

status

Action

• The screen

is blank, or

shows Put in

charger and

ﬂashes.

• The battery

has no

charge or

very little

charge. The

handset

cannot be

used.

• Charge

without

interruption

(at least 30

minutes).

• The screen

shows Low

battery and

ﬂashes.

• The battery

has enough

charge to be

used for a

short time.

• Charge

without

interruption

(at least 30

minutes).

• The screen

shows

HANDSET X.

• The battery is

charged.

• To keep

the battery

charged,

place it in

the handset

charger

when not in

use.

When it is fully charged, you can expect

the following performance:

Operation • Operating time *

Talk time (cordless

handset)

• 7 hours

Standby • 5 days

* Operating times vary depending

on your actual use and the age of the

battery.

Check the battery level

After you have installed the battery,

check the battery level on the handset

screen.

• If the screen is blank, or ﬂashes,

then the battery needs to be

charged. Go to Charge the battery

section before you do any setting or

operation.

• If the battery icon is , , or , then

go to Set the date and time and

Set the answering system through

voice guide section.

Check for dial tone

Press . If you hear a dial

tone, the installation is successful.

If you do not hear a dial tone

• Make sure the installation

procedures are properly done.

• The handset may take a second or

two to ﬁnd the telephone base and

produce a dial tone. This is normal.

Wait an extra second before dialing.

• If the previous suggestions do not

work, disconnect the telephone

line cord from your telephone and

connect the telephone line cord to

another telephone.

• If there is no dial tone on that other

telephone either, your telephone

line cord may be defective. Install a

new telephone line cord.

• If changing the telephone line

cord does not help, the wall jack

(or the wiring to this wall jack) may

be defective. Try using a different

wall jack in your home to connect

your CS5229/CS5229-2/CS5229-3/

CS5229-4/CS5229-5 telephone,

or contact your telephone service

provider (charges may apply).

18 19

Before use

Set date and time (before use)

After you install your telephone or

power returns following a power outage

and battery depletion, the handset will

prompt you to set the date and time,

and to conﬁgure the answering system

through voice guide.

NOTE

• Make sure you set the date and

time including the year correctly;

otherwise the answering system does

not announce the correct day of the

week for your recorded messages

time stamp.

1. Use the dialing keys (0-9) to enter the

month (MM), date (DD) and year (YY).

Then, press .

2. Use the dialing keys (0-9) to enter the

hour (HH) and minute (MM). Then

press q CID or p to choose AM

or PM.

3. Press to save.

After setting the date and time, the

handset will prompt if you want to set

Answering system (before use).

TIP

• To skip setting the date and time,

press on the handset.

Set up through voice guide - Answering

system (before use)

After the date and time setting is done or

skipped, the handset will then prompt if

you want to set up the answering system.

This feature assists you to do the basic

setup of the answering system. You can

follow the voice guide to record your

own announcement, set the number of

rings and the message alert tone.

1. Press to start the

answering system setup via voice

guide. You hear the voice prompt “

Hello! This voice guide will assist you

with the basic setup of your answering

system.”

• To skip the set up, press

2. Setup your answering system by

inputting the designated numbers as

instructed in the voice guide.

Alternate way to set up

1. Press on the

telephone base when it is not in use.

2. Press q CID or p to scroll to

Answering sys, and then press

3. Press q CID or p to scroll to Voice

guide, the press .

You hear the voice prompt “Hello!

This voice guide will assist you with

the basic setup of your answering

system.”

4. Set up your answering system by

inputting designated numbers as

instructed in the voice guide.

NOTE

• You can press to quit

the voice guide at any time.

Install

Mount the telephone base

Your telephone base is ready for tabletop

use. If you want to mount your telephone

on a wall, use the provided wall-mount

bracket to attach to a standard dual-stud

telephone wall-mounting plate.

If you do not have this wall-mounting

plate, you can purchase one from many

hardware or consumer electronics

retailers. You may need a professional to

install the wall-mounting plate.

20 21

Overview

Telephone base

light

• On when the phone

is in use, or when the

answering system is

answering a call.

• On when a handset is

being registered.

• Flashes when there is

an incoming call.

• Flashes when

handsets are being

deregistered.

• Flashes when another

telephone on the

same line is in use.

2Message

window

• Shows the number of

unread messages.

• X/DELETE

• Press to delete

the message or

announcement

currently playing.

• When the phone

is not in use, press

twice to delete all

previously reviewed

messages.

• /REPEAT

• Press to repeat a

message or press

twice to play the

previous message.

• /SKIP

• During message

playback, press to skip

to the next message.

• /PLAY/STOP

• Press to play

messages.

• Press to stop message

playback.

• Flashes when there

are new messages

or memos in the

answering system.

4- VOL +

• Press to adjust the

listening volume during

a call.

• When the phone is not

in use, press to adjust

the telephone base

ringer volume.

5 ANS ON

• Press to turn on the

answering system and

press again to turn off.

The light is on when on

the answering system is

on.

6 / FIND

HANDSET

• Press the button to page

all system handsets.

7Antenna

Handset

1LCD display

2MENU/

SELECT

• Press to display the

menu.

• Once in the menu, press

to select an item or save

an entry or setting.

22 23

• / pVOLUME

• Press to show

phonebook entries

when the telephone is

not in use.

• Press to scroll up while

in a menu.

• Press to increase the

listening volume when

on a call, or increase

the message playback

volume.

• While entering names

or numbers, press to

move the cursor to the

right.

• VOLUMEq/CID

• Press to review the

caller ID log when the

telephone is not in

use.

• Press to scroll down

while in a menu.

• Press to decrease the

listening volume when

on a call, or decrease

the message playback

volume.

• While entering names

or numbers, press to

move the cursor to the

left.

4OFF/

CANCEL

• During a call, press to

hang up.

• While in a menu, press

to cancel an operation or

back up to the previous

menu; or press and hold

this button to exit menu

display completely.

• When the handset is

ringing, press to mute

the ringer temporarily.

• Press and hold while

the handset is not in use

to erase the missed call

indicator.

5QUIET #

• Press and hold to set

and turn on the QUIET

mode, or turn it off.

• When reviewing a

caller ID log entry, press

repeatedly to view other

dialing options.

6INT

• Press to start an intercom

conversation or transfer

a call (for multi-handset

models only).

7MUTE/

DELETE

• Mute the microphone

during a call.

• Delete digits or

characters while using

the dialing keys.

• Silence the ringer

temporarily while the

handset is ringing.

8CHARGE

light

• On when the handset

is charging in the

telephone base or

charger.

9REDIAL/

PAUSE

• Press repeatedly to view

the last 10 numbers

dialed.

• While entering numbers,

press and hold to insert a

dialing pause.

TALK/

FLASH

• Press to make or answer

a home call.

• During a call, press to

answer an incoming call

when you receive a call

waiting alert.

11 1

• While reviewing a caller

ID log entry, press

repeatedly to add or

remove 1 in front of

the telephone number

before dialing or saving

it in the phonebook.

• Press and hold to set

or dial your voicemail

number.

• Press to switch to tone

dialing temporarily

during a call if you have

pulse service.

• Press to make or

answer a call using the

speakerphone.

• Press to turn on the

handset speakerphone,

press again to resume

normal handset use.

1Charging pole

Display

HANDSET 1

MUTE NEW

ANS ON

10:30

AM 10/16

MSG #

1• The battery is low

and needs charging.

2• The battery is

charging.

3• The battery is fully

charged.

4• Handset ringer is off.

• New voicemail

received from your

telephone service

provider.

NEW

• There are new caller

ID log entries.

7ANS ON • Answering system is

on.

810/16

MSG # • Number of new/old

messages recorded.

9MUTE

• The handsest

microphone is

muted while on a

call.

Handset lights

1CHARGE

• On when the

handset is charging

in the telephone

base or charger.

• On when the

speakerphone is in

use.

24 25

Telephone base lights

1IN USE

• On when the telephone

line is in use.

• On when the answering

system is answering a

call.

• On when you are

registering a handset.

• Flashes quickly when

there is an incoming call.

• Flashes when another

telephone sharing the

same line is in use.

• Flashes when you

are deregistering all

handsets.

2 ANS ON • On when the answering

system is turned on.

Operating range

This cordless telephone operates with

the maximum power allowed by the

Federal Communications Commission

(FCC). Even so, this handset and

telephone base can communicate over

only a certain distance which can vary

with the locations of the telephone base

and handset, the weather, and the layout

of your home or ofﬁce.

When the handset is out of range, the

handset displays Out of range or no pwr

at base.

If there is a call while the handset is out

of range, it may not ring, or if it does

ring, the call may not connect well when

you press . Move closer

to the telephone base, and then press

to answer the call. If

the handset moves out of range during

a telephone conversation, there may

be interference. To improve reception,

move closer to the telephone base.

Operate

Make, answer or end a call

Make a call

Press or on the

handset, then enter the telephone

number.

Predial a call

Enter the telephone number, then press

or to dial.

Answer a call

Press or , or any

dialing keys (0-9 or or QUIET#).

End a call

Press or put the handset

in the telephone base or charger.

NOTES

• The handset displays Unable to call.

Try again if the telephone line is in

use.

• The screen shows the elapsed time

as you talk (in hours, minutes and

seconds).

• When predialing (preview numbers

before dialing), press

on the handset to backspace

and delete; press and hold

to insert a dialing

pause (a p appears).

View dialing options

Although the caller ID log entries may

contain 10 digits (the area code plus the

7-digit number), in some areas, you may

dial a 1 plus the seven digits, or a 1 plus

the area code plus the seven digits. You

can change the number of digits that

you dial from the caller ID log or store

to the phonebook.

While reviewing the caller ID log, press

# (pound key) repeatedly to show

different dialing options for local and

long distance numbers before dialing

or saving the telephone number in the

phonebook.

Press 1 repeatedly if you need to add

or remove 1 in front of the telephone

number before dialing or saving it in

the phonebook.

When the number shows the correct

format for dialing:

Press or on the

handset to call the number.

NOTE

• 7-digit local dialing will be invalid

from October 2021 onwards. Press #

(pound key) repeatedly to select the

appropriate dialing option.

26 27

Sound

Use speakerphone

During a call, press to switch between

the speakerphone and normal handset

use.

To hand up, press or return

the handset to the telephone base or

charger.

Volume control

During a call, press VOLUMEq or

VOLUMEp to adjust the listening

volume.

Mute the microphone

Use the mute function to turn off the

microphone. You can hear the caller, but

the caller cannot hear you.

To mute a call

While on a call, press on

the handset. The screen displays Muted

until the mute function is turned off.

To end mute a call

Press on the handset

again and resume speaking. The screen

brieﬂy displays Microphone on.

Mute is automatically cancelled when

you end the call.

Temporary ringer silencing

When the telephone is ringing, you can

temporarily silence the ringer of the

handset without disconnecting the call.

The next call rings normally at the preset

volume.

To silence the handset ringer

Press or on

the handset. The handset screen shows

Ringer muted.

To silence the telephone base ringer

Press VOL - once.

Join a call

Join a call in progress (for multiple

handset models only)

Another handset can join you on a call.

The call continues until all parties hang

up. You can share an outside call with

up to two system handsets.

• When a handset is already on a call,

press or on

another handset to join the call.

• Press or place the

handset in the telephone base or

handset charger to exit the call. The

call continues on the other handset

until both handsets hang up.

Transfer a call

Blind transfer (for multiple handset

models only)

While on an outside call, you can transfer

the call to a speciﬁc device or any

device without notifying them.

1. During a call, press .

2. Press qCID or p to scroll to Transfer

and then press .

• If you have two handsets, the

outside call is put on hold

and your handset displays

Transferring calls.... The other

handset rings and shows Transfer

from other handset.

• If you have other registered

device(s) or more than two

handsets, your screen shows

TRANSFER TO:. Use the dialing

keys to select the destination

device, or press qCID or p

to scroll to the desired device

and press . The

outside call is put on hold and

your handset screen shows

Transferring call... or Transferring

call to all.... The other device

rings and shows Transfer

from HANDSET X (HANDSET

represents the handset name, X

represents the handset number).

3. To answer the call on the destination

handset, press ,

, or any dialing key (0-9,

or QUIET#). The initiating handset

shows Call transferred and returns

to idle.

NOTE

• To cancel the intercom call before it

is answered, press .

• Press or

on the destination handset to

temporarily silence the intercom

ringer.

•

• To cancel the transfer and return to

the external call before the blind

transfer call is answered, press

, , or

on your handset.

28 29

Call waiting

If you subscribe to call waiting service

from your telephone service provider,

and someone calls while you are already

on a call, you hear an alert tone.

1. Press on the handset

to put your current call on hold and

take the new call.

2. Press on the handset

at any time to switch back and forth

between calls.

If you also subscribe to caller ID service, it

will let you see the name and telephone

number of the caller during call waiting.

It may be necessary to change your

telephone service to use this feature.

Contact your telephone service provide

if:

• You have both caller ID and call

waiting, but as separate service (you

may need to combine these service);

• You have only caller ID service, or

only call waiting service; or

• You do not subscribe to caller ID or

call waiting services.

There are fees for caller ID services. In

addition, services may not be available

in all areas.

Intercom

Use the intercom feature for conversations

between two handsets.

Initiate an intercom call

1. Press INT on your handset when not

in use.

• If you have two handsets, your

handset displays Calling other

handset.

• If you have three or more

handsets, press qCID or p to

highlight the desired device and

then press . Your

handset screen shows Calling

HANDSET X or Calling all handsets.

The destination handset rings and

shows Other handset is calling,

HANDSET X is calling or HANDSET

X is calling all (HANDSET represents

the handset name, X represents the

handset number).

2. To answer the intercom call, press

, , or any dialing

key (0-9, or QUIET#) on the

destination handset. Both handsets

now display Intercom.

3. To end the intercom call, press

or place the handset

back in the telephone base or charger.

Both handsets now display Intercom

ended.

NOTES

• To cancel the intercom call before it is

answered, press .

• Press or

on the destination handset to

temporarily silence the intercom

ringer.

• If the destination handset does not

answer the intercom call within 100

seconds, is accessing the answering

system, on a call or out of range,

the originating handset displays No

answer. Try again and returns to idle.

Answer an incoming call during an

intercom call

When you receive an outside call during

an intercom call, there is an alert tone.

• To answer the outside call, press

. The intercom call

ends automatically.

• To end the intercom call without

answering the outside call, press

. The telephone

continues to ring.

Transfer a call via intercom

Use the intercom feature to transfer an

outside call to another system handset.

You can also share an outside call with

another system handset.

1. During a call, press INT.

• If you have two handsets, the

outside call is put on hold and

your handset displays Calling

other handset.

• If you have three or more

handsets, press qCID or p

to highlight the desired device

and then press

. Your handset screen shows

Calling HANDSET X or Calling all

handsets.

2. When the destination handset picks

up, your handset shows Intercom

and the outside call is put on hold.

You have the following options:

• You can transfer the call. Press

, then press qCID

or p to scroll to Transfer.

Press again. The

handset shows Call transferred.

The other handset automatically

connects to the outside call.

• You can let the other handset

join you on the outside call in a

three-way conversation. Press

. Press qCID or

p to highlight Share call, then

press .

30 31

• You can end the intercom call and

continue the outside call with your

handset. Press . on

your handset (the ended intercom

call party hears four beeps).

NOTES

• To cancel the intercom call before it is

answered, press .

• Press or

on the destination handset to

temporarily silence the intercom

ringer.

• If the destination handset does not

answer within 100 seconds, is in

use, on a call or is out of range, the

originating handset displays Unable

to call. Try again and then reconnects

to the outside call.

Find handset

Page/ ﬁnd handset

CAUTIONS

• Do not press and hold /FIND HS for

more than four seconds. It may lead

to handset deregistration.

• If the handset displays To register HS,

see manual, refer to Register a handset

section to register the handset back to

the telephone base.

This feature helps you ﬁnd all system

handsets.

To start paging

Press /FIND HS on the telephone base

when it is not in use. All idle handsets ring

and display ** Paging **.

To end paging

• Press , , or any

dialing key (0-9, or QUIET#)

on the handset ;

-OR-

• Press /FIND HS again on the

telephone base;

NOTES

• If you press or

on a handset, the ringer

of that handset is silenced but the

paging tone continues on the other

handsets.

• If a handset is accessing the answering

system, on a call (intercom call or

outside call), or out of range, that

handset does not beep when

paged.

• You cannot use the ﬁnd handset

feature while the telephone base is

playing messages or the answering

system is being accessed remotely.

Use phone menu

1. Press to enter the

main menu when the telephone is

not in use.

2. Press qCID or p to scroll through

menu items.

3. Press to select or

save the highlighted item.

-OR-

Press to cancel

an operation, back up to the

previous menu; or press and hold

to exit the menu

display.

Phonebook | Phonebook

entry

The phonebook can store up to

50 entries, which are shared by all

handsets. Each entry may consist of a

telephone number up to 30 digits, and

a name up to 15 characters.

Any additions, deletions or edits made

on one handset will be reﬂected on

other handsets.

If the telephone number in the

phonebook exceeds 15 digits, a dash

appears after the 14th digit and then the

remaining digits are shown beginning

with a dash, alternately.

Add a phonebook entry

1. Press on the handset

when it is not in use.

2. Press qCID or p to highlight

Phonebook, then press

3. Press qCID or p to highlight Add

contact, then press .

• The screen shows ENTER

NUMBER.

4. Use the dialing keys to enter a

telephone number (up to 30 digits).

• Press q CID or p to move the

cursor to the left or right.

• Press on the

handset to erase a digit.

• Press and hold on

the handset to erase all digits.

• Press and hold

to insert a three-second dialing

32 33

pause (a p appears). -OR- Press

to copy a number

from the redial list. Press q CID

or p , or press

repeatedly to locate the desired

number. Press to

copy the displayed number.

5. Press to proceed to

entering name.

• The screen shows ENTER NAME.

6. Use the dialing keys to enter a name

(up to 15 characters) when prompted.

• Press a key repeatedly until the

desired character shows on the

screen.

• Press q CID or p to move the

cursor to the left or right.

• Press 0 to add a space.

• Press on the

handset to erase a character.

• Press and hold on

the handset to erase all characters.

• Press to change the next

letter to upper or lower case.

7. Press to store your

new phonebook entry.

- OR -

1. While the handset is not in use, use the

dialing keys to enter the telephone

number (up to 30 digits).

2. Press twice to move

on to edit the name.

3. Press to store your

new phonebook entry. You hear a

conﬁrmation tone.

Review the phonebook entries

1. Press p when the telephone is not

in use.

• The screen shows the ﬁrst entry in

the phonebook.

2. Press q CID or p to browse

through the phonebook or use the

dialing keys to start a name search.

-OR-

1. Press when the

telephone is not in use.

2. Press q CID or p to scroll to

Phonebook, then press .

3. Press again to choose

Review.

• The screen shows the ﬁrst entry in

the phonebook.

4. Press q CID or p to scroll to browse

through the phonebook.

• Entries appear alphabetically by

the ﬁrst letter in the name.

Dial a phonebook entry

1. Search for the desired entry in

the phonebook (see Review the

phonebook entries or Alphabetical

search).

2. When the displayed number is in the

correct format, press

or on the handset to dial.

Delete a phonebook entry

1. While reviewing a phonebook entry

(see Review the phonebook entries

or Alphabetical search), press

• The screen shows Delete

contact?.

2. Press to delete the

displayed entry from the phonebook.

• The handset shows Contact

deleted and then you hear a

conﬁrmation tone.

NOTE

• Once deleted, you cannot retrieve

that entry.

Edit a phonebook entry

1. While reviewing a phonebook entry,

press .

• The screen shows EDIT NUMBER

with the current number of the

entry.

2. Use the dialing keys to edit the

number (up to 30 digits).

• Press q CID or p to move the

cursor to the left or right.

• Press and hold

to insert a three-second dialing

pause (a p appears).

• Press on the

handset to erase a digit.

• Press and hold

on the handset to erase all

digits. -OR- Copy a number

from the redial list by pressing

and then

q CID or p , or pressing

repeatedly

to locate the desired number.

Press to copy the

number.

3. Press to save the

number.

• The screen shows EDIT NAME

brieﬂy and then the current name

of the entry.

4. Edit the characters.

• Press 0 to add a space.

• Press q CID or p to move the

cursor to the left or right.

• Press on the

handset to erase a character.

• Press and hold

on the handset to erase all

characters.

5. Press to save.

• The handset shows the updated

entry.

34 35

Alphabetical search

You can use the enhanced 3-character

search to ﬁnd your contacts quickly and

efﬁciently.

1. Press p when the handset is not in

use.

2. When an entry appears, use the

dialing keys (0-9) to start a name

search (alphabetical search).

• The phonebook shows the ﬁrst

name beginning with the ﬁrst

letter associated with the dialing

key, i.e. if there is an entry in the

phonebook that begins with that

letter.

• Press q CID or p to scroll

through the entries beginning

with that letter.

3. To see other names that start with the

letters on the same dialing key, keep

pressing the key until the desired

letter is shown.

• The names appear in alphabetical

order.

For example, if you have the names

Jennifer, Jessie, Kevin and Linda in your

phonebook:

• If you press 5 (JKL) once, J and then

Jennifer displays.

• If you press 5 (JKL) once, J displays.

Press q. Jessie displays.

• If you press 5 (JKL) twice, K and then

Kevin displays.

• If you press 5 (JKL) three times, L and

then Linda displays.

• If you press 5 (JKL) four times, 5

displays.

• If you press 5 (JKL) ﬁve times, J displays

and then Jennifer displays again.

NOTE

• If you press a dialing key (0-9) and

no name starts with any letter on that

key, the phonebook shows the entry

that matches the next letter in the

phonebook.

Redial list

Each handset stores the last 10 telephone

numbers dialed. Entries are shown in

reverse chronological order. When

there are already 10 entries, the oldest

entry is deleted to make room for the

new entry.

Review a redial list entry

1. Press when the

handset is not in use.

2. Press p , q CID or

repeatedly to browse until the

desired number displays. The

handset beeps twice at the end of

the list.

3. Press on the handset

to exit.

Dial a redial list entry

When the desired redial entry displays,

press or to dial.

- OR -

1. Press or .

2. Press to enter the

redial list.

3. Press p , q CID or

repeatedly to browse until the

desired entry displays.

4. Press to dial the

displayed number.

Save a redial entry to the phonebook

1. When the desired redial entry

displays, press twice.

2. When the screen shows EDIT

NUMBER, use the dialing keys to

modify the telephone number (up

to 30 digits).

• Press q CID or p to move the

cursor to the left or right.

• Press and hold to

enter a 3-second dialing pause (a

p appears).

• Press to erase a

digit.

• Press and hold to

erase all digits.

3. Press to save the

number in the display.

• The screen shows EDIT NAME.

4. Use the dialing keys to modify the

name (up to 15 characters).

• Press 0 to add a space.

• Press q CID or p to move the

cursor to the left or right.

• Press on the

handset to erase a character.

• Press and hold

on the handset to erase all

characters.

5. Press to save.

• You hear a conﬁrmation tone.

36 37

Delete a redial list entry

1. Press on the handset

when it is not in use.

2. Press p , q CID or

repeatedly to browse until the desired

number displays.

3. Press on the handset

to delete the displayed number.

• You hear a conﬁrmation tone.

Chain dialing

Use this feature to initiate a dialing

sequence from numbers stored in the

phonebook, caller ID log or redial list

while you are on a call.

Chain dialing is useful if you wish to

access other numbers (such as bank

account numbers or access codes) from

the phonebook, caller ID log or redial

list.

Access a number in the phonebook

while on a call

1. Press .

2. Press to select

Phonebook .

3. Press q CID or p to scroll to

the desired entry or perform an

alphabetical search, then press

to dial the displayed

number.

Access a number in the caller ID log

while on a call

1. Press .

2. Press q CID or p to scroll to Caller

ID log, then press .

3. Press q CID or p to scroll to

the desired entry, and then press

to dial the displayed

number.

Access the redial list while on a call

1. Press .

2. Press p , q CID or

until the desired number displays.

3. Press to dial the

displayed number.

NOTES

• You cannot edit a phonebook entry

while on a call.

• You cannot copy a caller ID log entry

into the phonebook while on a call.

• You can only view the numbers in the

phonebook, caller ID log or redial

list while on a call and cannot edit,

delete or save entries.

• Press on the handset

to exit redial list, phonebook or caller

ID log while on a call.

Caller ID

If you subscribe to caller ID service,

information about each caller appears

after the ﬁrst or second ring. If

you answer a call before the caller

information appears on the screen, it

will not be saved in the caller ID log.

The caller ID log stores up to 30 entries.

Each entry has up to 24 digits for the

phone number and 15 characters for

the name.

Review the caller ID log

Review the caller ID log to ﬁnd out who

called, to return the call or to copy the

caller’s name and number into your

phonebook.

1. When a handset is not in use, press

q CID to view the caller ID log in

reverse chronological order starting

with the most recent call.

-OR-

You can also review the

caller ID log by pressing

when the handset

is not in use, then press q CID or

p to scroll to Caller ID log. Press

twice to select

Review.

2. Press q CID or p to scroll through

the list. The handset beeps twice

when you reach the beginning or

end of the caller ID log.

3. Press to exit the caller

ID log.

38 39

Save a caller ID log entry to the phonebook

1. While reviewing the caller ID log, press

q CID or p to browse through the

caller ID log.

2. When the desired entry displays,

press .

3. Press again to choose

Phonebook.

4. When the screen shows EDIT

NUMBER, use the dialing keys to

modify the telephone number (up to

30 digits).

• Press q CID or p to move the

cursor to the left or right.

• Press and hold to

enter a 3-second dialing pause (a

p appears).

• Press to erase a

digit.

• Press and hold to

erase all digits.

5. Press to save the

number in the display.

• The screen shows EDIT NAME.

6. Use the dialing keys to modify the

name (up to 15 characters).

• Press 0 to add a space.

• Press q CID or p to move the

cursor to the left or right.

• Press on the

handset to erase a character.

• Press and hold on

the handset to erase all characters.

• Press to change the next

letter to upper or lower case.

7. Press to save.

• You hear a conﬁrmation tone.

NOTES

• If a number is already in the

phonebook. You cannot save the

same number more than once.

• If you try to save a caller ID log entry

to the phonebook without a number,

the handset sounds an error tone.

• If the telephone number has more

than 15 digits, only the last 15 digits

appear in the caller ID log. However,

the telephone can still save all digits

(up to 24 digits) of that telephone

number from the caller ID log in the

phonebook.

• You might need to change how

a caller ID number is saved in the

phonebook if the entry does not

appear in the correct format. Caller

ID numbers might appear without a

1 that is necessary for long distance

calls.

• Caller ID log entries are shared by all

system handsets. Any deletions made

on one handset are reﬂected on all

other handsets.

Save a caller ID log entry to call block

list

1. Search for the desired caller ID log

entry (see Review call block list).

2. When the desired entry displays,

press .

3. Press q CID or p to scroll to Block

list, then press .

4. The handset displays EDIT NUMBER.

Use the dialing keys to edit the

number, when necessary.

• Press q CID or p to move the

cursor to the left or right.

• Press to

backspace and erase a digit.

• Press and hold to

erase the entire entry.

• Press and hold to

enter a 3-second dialing pause (a

p appears).

5. Press to move to the

name.

• The screen shows EDIT NAME.

6. Use the dialing keys to to add or

edit the name.

• Press q CID or p to move the

cursor to the left or right.

• Press 0 to add a space.

• Press on the

handset to erase a character.

• Press and hold

on the handset to erase all

characters.

• Press to change the next

letter to upper or lower case.

7. Press to save.

Dial a caller ID log entry

1. Search for the desired entry in the

caller ID log (see Review the caller

ID log).

2. When the desired entry is displayed

and is in the correct format for

dialing:

• Press or

on the handset to dial with the

home line.

Delete caller ID log entries

1. Search for the desired entry in the

caller ID log (see Review the caller

ID log).

2. When the desired entry is displayed,

press on the handset.

You hear a conﬁrmation tone.

To delete all entries

1. Press on the handset

when it is not in use.

2. Press q CID or p to highlight Caller

ID log, then press .

3. Press q CID or p to highlight Del

all calls?, then press .

4. When the screen shows Delete

all calls?, press to

conﬁrm.

• There is a conﬁrmation tone

and the screen returns to the

previous menu.

La page charge ...

VTech CS5229-3 Manuel utilisateur

Marque: VTech

Modèle: CS5229-3

Catégorie: Téléphones

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS5229-3 User manual

VTech CS5229-3 Manuel utilisateur

Ce manuel convient également à

VTech CS5229-3 Manuel utilisateur

dans d''autres langues

Documents connexes