EcoFlow RIVER Manuel utilisateur

EcoFlow RIVER User Manual

EcoFlow RIVER （Hereinafter referred to as RIVER）

Read all safety tips, warning messages, terms of use, and disclaimers carefully. Refer to the

terms of use and disclaimer at https://ecoflow.com/pages/terms-of-use and stickers on

the product before use. Users take full responsibility for all usage and operations. Familiarize

yourself with the related regulations in your area. You are solely responsible for being aware

of all relevant regulations and using EcoFlow products in a way that is compliant.

DISCLAIMER

1

3

4

6

7

8

9

10

11

3.1 Product Details

3.2 LCD Screen

3.3 General Product Usage

3.4 AC Charging

3.5 Solar Charging

3.6 Car Charging

3.7 APP

3.8 X-Boost

3.9 Emergency Power Supply (EPS)

1.

2. Safety Instructions

3. Getting Started

4. FAQs

5. Troubleshooting

6. What’s In the Box

7. Storage & Maintenance

CONTENTS

Specifications

2

2.1 Usage

2.2 Disposal Guide

1

1. Specifications

Input Ports

AC Charge

AC Input Voltage

Solar Charger

Car Charger

X-Stream Fast Charge 250W Max, 10A

220-240V~ 50Hz/60Hz, 10A

10-25V 12A, 200W Max

Supports 12V Battery, 8A

Max Device(s) Power Supported by X-Boost

USB-A (x2)

USB-A Fast Charge (x1)

USB-C (x1)

Car Charger(x1)

DC5521 Output (x2)

1800W

5V 2.4A 12W Max, per port, 24W total

5V 2.4A 9V 2A 12V 1.5A 18W Max, per port

5/9/12/15/20V 5A 100W Max, per port

13.6V 10A, 136W Max

13.6V 3A, per port

General Info

Output Ports

Net Weight

Dimensions

Capacity

Wi-Fi

Approximately 11lbs(5kg)

11.3in x 7.3in x 7.7in(28.8 x 18.5 x 19.4cm)

288Wh 28.8V

Supported

Battery Info

Cell Chemistry

Cycle Life

Lithium-ion

500 cycles to 80%+ capacity

* Car charger shares power with the DC5521 output port, offering a maximum output of 136W.

AC (x2) Pure Sine Wave, 600W total (Surge 1200W),

230V~ (50Hz/60Hz)

Environmental Operating Temperature

Optimal Operating Temperature

Discharge Temperature

Charge Temperature

Storage Temperature

* Whether the product can be charged or discharged depends on the actual temperature of the battery pack.

20°C~30°C (68°F~86°F)

-20°C~45°C (-4°F~113°F)

0°C~45°C (32°F~113°F)

-20°C~45°C (-4°F~113°F)

(optimal: 20°C~30°C(68°F~86°F))

Protection Over Voltage Protection, Overload Protection, Over

Temperature Protection, Short Circuit Protection,

Low Temperature Protection, Low Voltage Protection,

Overcurrent Protection

2

2.2 Disposal Guide

2. Safety Instructions

1. If conditions permit, make sure that the battery is fully discharged before disposing it in a designated

battery recycling bin. The product contains batteries with potentially dangerous chemicals, so it is

strictly prohibited to dispose of it in ordinary trash cans. For more details, please follow the local laws

and regulations on battery recycling and disposal.

2. If the battery cannot be fully discharged due to a product failure, please do not dispose of the

battery directly in the battery recycling box. In such case, you should contact a professional battery

recycling company for further processing.

3. Please dispose of over-discharged batteries that cannot be recharged.

1. Do not use the product near a heat source, such as a fire source or a heating furnace.

2. Avoid contact with any liquid. Do not immerse the product in water or get it wet. Do not use the

product in rain or humid environments.

3. Do not use the product in an environment with strong static electricity/magnetic fields.

4. Do not disassemble the product in any way or pierce the product with sharp objects.

5. Avoid using wires or other metal objects that may result in a short circuit.

6. Do not use unofficial components or accessories. If you need to replace any components or

accessories, please visit official EcoFlow channels to check relevant information.

7. When using the product, please strictly follow the operating environment temperature specified in

this user manual. If the temperature is too high, it may result in a fire or explosion; if the temperature

is too low, the product performance may be severely reduced, or the product may cease to work.

8. Do not stack any heavy objects on the product.

9. Do not lock the fan forcibly during use or place the product in an unventilated or dusty area.

10. Please avoid impact, falls, or severe vibrations when using the product. In case of a severe external

impact, turn off the power supply immediately and stop using the product. Ensure the product is

well fastened during transportation to avoid vibrations and impacts.

11. If you accidentally drop the product into water during use, please place it in a safe open area, and

stay away from it until it is completely dry. The dried product should not be used again, and should

be properly disposed of according to Section 2.2 below. If the product catches fire, we recommend

that you use the fire extinguishers in the following order: water or water mist, sand, fire blanket, dry

powder, and finally a carbon dioxide fire extinguisher.

12. Use a dry cloth to clean off dirt on the product ports.

13. Rest the product on a flat surface to avoid damages caused by the product falling over. If the

product is overturned and severely damaged, turn it off immediately, place the battery in an open

area, keep it away from combustible matter and people, and dispose of it in accordance with local

laws and regulations.

14. Ensure that the product is kept out of reach of children and pets.

2.1 Usage

3

LCD Screen

Solar/Car Charging Input Port

AC Output Sockets

Power Earth Screw

AC Power Button

USB-A Output Port

IOT Button

LED Light

ON/OFF Button

X-Stream AC

Charging Input Port

USB-C 100W Output Port

DC Power Button

USB-A Fast Charge

Output Port

Overload Protection Switch

Main Power Button

3.1 Product Details

Ventilation Fan

3. Getting Started

Car Outlet

DC5521 Output Port

International Version

4

3.2 LCD Screen

3.3 General Product Usage

Short Press to Turn On Long Press to Turn Off

Remaining Charge/

Discharge Time

Overload Warning

Fan Indicator

Low Temperature Warning

High Temperature Warning

Remaining Battery Percentage

Battery Failure Warning

Battery Level Indicator

Extra Battery

Indicator

AC Output

Wi-Fi Status

DC Output Indicator

State of Charge

USB-A Output

USB-C Output

Output Power

Input Power

Battery Level Indicator: The indicator will repeatedly fill while charging. If product is at 0% charge, the

indicator will flash to warn you.

Wi-Fi Status: After pressing the IOT button for 3 seconds, the Wi-Fi status will flash on the LCD screen

which indicates that the product is ready for pairing. There're two ways to connect the product with

the App, either directly connect to the product's hotspot or using the Internet. If the App is successfully

connected to the product's hotspot, the icon will keep flashing; if it is successfully connected to the

Internet, the icon will stay on.

* See Section 5 for more troubleshooting steps.

Short press the Main Power Button to turn on the product; the LCD Screen will light up and the

battery level indicator icon will display.

Product On, Product Off, LCD Screen On

The product enters sleep mode after 5 minutes of idle operation; the LCD Screen will automatically

turn off. When the product senses any load change or operations, the LCD Screen will automatically

light up. To turn the LCD Screen on or off, please short press the Main Power Button.

To power off the product, press and hold the Main Power Button.

The default product standby time is 2 hours. With other Power Buttons turned off and no other load

access for 2 hours, the product will automatically shut down. The standby time can be set on the App.

5

With the Main Power Button turned on, short press the

DC Power Button to use the DC Output port. Short press

the DC Power Button again to turn it off.

With the DC Power Button on, the product will not

automatically shut down.

DC Output Port

With the Main Power Button turned on, short press the

AC Power Button to use the AC Output ports. Short press

the AC Power Button again to turn it off.

The default standby time of the AC Output port is 12 hours.

Without any load access for 12 hours, the AC Power Button

will automatically turn off.

Please turn off AC power button when not in use to save

power consumption.

AC Output Port

Short Press

DC Power Button

Short Press

AC Power Button

6

X-Stream Fast Charging

250W Max input Power

<2 hrs Full Charge

3.4 AC Charging

Users can connect solar panels in series as shown in the figure to recharge the product.

When using an EcoFlow solar panel to charge the product, please follow the instructions that come

with the solar panel.

Before connecting the solar panel, please ensure that the solar panel’s output voltage is within

voltage range to avoid product damage.

3.5 Solar Charging

AC Charging Cable

X-Stream is an AC fast charge technology that recharges your portable power station at the fastest

speed possible. For slower,quieter charging, download the EcoFlow app and enable Slow Charging.

The unit will shut down if the current from an AC source exceeds 10A for an extended period.

The Overload Protection Switch will need to be pressed before powering the unit back on.

MC4

Please use AC charging Cable for fast charging. EcoFlow takes no responsibilities for any

consequences caused by failures to follow instructions, including but not limited to charging with

AC charging Cable.

Solar Charging

Cable

7

3.6 Car Charging

Users can recharge the product through the Car Charging Input Port. Please charge using the

car charger after you’ve started the car to avoid failure to start due to insufficient car battery. In

addition, please make sure that Car Charging Input Port and the Car Charging Cable are in good

condition. EcoFlow takes no responsibilities for any losses or damages caused by failures to follow

instructions.

3.7 APP

The EcoFlow App gives users the ability to control and monitor EcoFlow power stations remotely.

Read the EcoFlow App user guide and access the download link here:

https://ecoflow.com/pages/ecoflow-app

Privacy Policy

By using EcoFlow Products, Applications and Services, you consent to the EcoFlow Term of Use and

Privacy Policy, which you can access via the "About" section of the "User" page on the EcoFlow App

or on the official EcoFlow website at https://ecoflow.com/pages/terms-of-use and

https://ecoflow.com/pages/privacy-policy

Car Charging Cable

8

To avoid operation failure due to overload protection, the X-Boost feature will be automatically

enabled when the total output exceeds the rated output power, which enables the product to

power high wattage appliances at the rated output power.

X-Boost Tips:

1. X-Boost is enabled by default; you can enable or disable it in the EcoFlow App.

2. X-Boost is not available when the AC output is turned on in a recharging state (in bypass mode)

and when X-Boost is disabled.

3. X-Boost is not applicable for all electrical appliances; it’s incompatible with appliances with strict

voltage requirements. Appliances with voltage protection (such as precise instruments) are not

supported. X-Boost mode is more suitable for heating devices. Please conduct your own tests with

your devices with X-Boost enabled.

3.8 X-Boost

The product supports EPS. When you connect the grid power to the AC Input Port of the product

through an AC Charging cable, you can power electrical devices through the AC Output Sockets (AC

power will come from the grid and not the power station in this situation). In case of a sudden blackout,

the product can automatically switch to the battery powered supply mode within 30ms. As a basic

UPS function, this function does not support 0ms switching. Please do not connect the product to

any device that requires 0ms UPS, such as data servers and workstations. Please test and confirm

the compatibility before using the product. We recommend that you only charge one device at a

time and avoid using multiple ones at the same time to avoid overload protection. EcoFlow takes no

responsibilities for any device failures or data losses caused by failures to follow instructions.

3.9 Emergency Power Supply (EPS)

9

1. ls there an extra battery unit that adds capacity?

Yes, this product does have expandable capacity. Please refer to the user manual of RIVER extra

battery for detailed instruction.

2. What battery does the product use?

It uses high-quality lithium-ion battery.

3. What devices can the product’s AC output port power?

This device can power plenty of your appliances and devices. Before you use it, we recommend

that you confirm the power of the appliances first and ensure the power sum of all loaded

appliances is lower than the rated power.

4. How long can the product charge my devices?

The charging time is shown on the product’s LCD Screen, which can be used to estimate the

charging time of most appliances with stable power usage.

5. How can I know if the product is charging?

When it’s charging, the remaining charging time will be shown on the LCD Screen. Meanwhile, the

charging indicator icon begins to rotate with the remaining battery percentage and the input

power shown on the right of the circle.

6. How to clean the product?

Please gently wipe it with a dry, soft, clean cloth or paper towel.

7. How to store the product?

Before storing, please turn off the product first, and then store it in a dry, ventilated place at room

temperature. Do not place it near water sources. For long-term storage, please discharge the

battery to 30% and recharge it to 60% every three months to extend its battery life.

8. Can I bring the product on a plane?

No.

4. FAQs

10

5. Troubleshooting

If the Alarm Prompt shows on the product LCD screen during use and does not disappear after a

restart, please stop using it immediately (do not try to charge or discharge).

If you require any other assitance, please contact EcoFlow Customer Service.

Indicator Problem

Charging can be resumed

automatically after the battery cools

down.

The power supply can be resumed

automatically after the battery cools

down.

Charging can be resumed

automatically after battery

temperature rises above 5°C(41°F).

The power supply can be resumed

automatically after the battery

temperature rises above -12°C(10°F).

Please confirm whether the fan inlet

and outlet are blocked, if not, normal

operation will be resumed automatically

after the product temperature drops.

Normal operation will be resumed

automatically after the product is

used at optimum environmental

temperatures.

Please check if the fan is blocked by

foreign materials.

After the product cools down,

it will resume normal operation

automatically.

Contact EcoFlow Customer Service

Normal operation will be resumed

automatically after you remove the

overloaded device and restart the

product.

Electrical appliances should be used

within rated power.

(Refer to X-Boost instructions to get

more details about power limitations).

Solution

The product will resume normal

operation automatically after you

remove the device connected to the car

charger.

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icons Flash

together

Icon Stays On

High Temperature

Charge Protection

High Temperature

Discharge Protection

Low Temperature

Charge Protection

Low Temperature

Discharge Protection

AC Output

Overload Protection

AC High

Temperature Protection

AC Low

Temperature Protection

Fan Blockage

Car Charger

Overload Protection

Car Charger High

Temperature Protection

Battery Failure

Icon Flashes

Overload Discharging

Protection

Battery Exclamation and

OVERLOAD icons flash together.

Disconnect all appliances, restart

the RIVER, and add each appliance

back in in turn. Please note that

electrical appliances must be

operated within rated power.

11

1. Ideally, use and store the product between 20°C to 30°C(68°F to 86°F), and always keep it away

from water, intense heat, and sharp objects. Do not store in temperatures above 45°C(113°F) or

below -10°C(14°F) for an extended period.

2. Storing a battery with a low charge for a long period shortens its lifespan. This product mitigates

the damage by putting the battery into hibernation mode. To get the most out of the battery, make

sure it is about 60% before putting this product into long-term storage, and then once every three

months, discharge the battery to 30% and recharge it back to 60%.

6. What’s In the Box

7. Storage & Maintenance

RIVER

User Manual and War-

ranty Card

DC5521-DC5525

Cable

AC Charging Cable (1.5m) Car Charging Cable

(1.5m)

Solar Charging Cable

(MC4 to XT60 Input)

EcoFlow RIVER Benutzerhandbuch

EcoFlow RIVER （nachfolgend als RIVER bezeichnet）

Lesen Sie alle Sicherheits- und Warnhinweise, Nutzungsbedingungen und Haftungsausschlüsse

sorgfältig durch. Lesen Sie vor der Verwendung die Nutzungsbedingungen und den

Haftungsausschluss unter https://ecoflow.com/pages/terms-of-use sowie die Aufkleber auf

dem Produkt. Benutzer übernehmen die volle Verantwortung für Verwendung und Betrieb des

Produkts. Machen Sie sich mit den entsprechenden Vorschriften in Ihrem Land vertraut. Sie

sind allein dafür verantwortlich, alle relevanten Vorschriften zu kennen und EcoFlow-Produkte

gemäß diesen Vorschriften zu verwenden.

HAFTUNGSAUSSCHLUSS

1

3

4

6

7

8

9

10

11

3.1 Produktdetails

3.2 LCD-Anzeige

3.3 Allgemeine Betriebsanweisungen

3.4 AC-Ladung

3.5 Solarladung

3.6 Kfz-Ladung

3.7 App

3.8 X-Boost

3.9 Notstromversorgung

1.

2. Sicherheitshinweise

3. Erste Schritte

4. FAQ-Bereich

5. Fehlerbehebung

6. Lieferumfang

7. Lagerung und Wartung

INHALT

Spezifikationen

2

2.1 Verwendung

2.2 Sachgemäße Entsorgung

La page charge ...

EcoFlow RIVER Manuel utilisateur

EcoFlow RIVER Manuel utilisateur

dans d''autres langues

Documents connexes