Advantech EPC-U2117 Manuel utilisateur

User Manual

EPC-U2117

EPC-U2117 User Manual ii

Copyright

The documentation and the software included with this product are copyrighted 2019

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to make improvements in the products described in this manual at any time without

notice.

No part of this manual may be reproduced, copied, translated or transmitted in any

form or by any means without the prior written permission of Advantech Co., Ltd.

Information provided in this manual is intended to be accurate and reliable. However,

Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements

of the rights of third parties, which may result from its use.

Acknowledgements

Intel® and Pentium® are trademarks of Intel Corporation.

Microsoft Windows® is a registered trademark of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

Product Warranty (2 years)

Advantech warrants to you, the original purchaser, that each of its products will be

free from defects in materials and workmanship for two years from the date of pur-

chase.

This warranty does not apply to any products which have been repaired or altered by

persons other than repair personnel authorized by Advantech, or which have been

subject to misuse, abuse, accident or improper installation. Advantech assumes no

liability under the terms of this warranty as a consequence of such events.

Because of Advantech’s high quality-control standards and rigorous testing, most of

our customers never need to use our repair service. If an Advantech product is defec-

tive, it will be repaired or replaced at no charge during the warranty period. For out-

of-warranty repairs, you will be billed according to the cost of replacement materials,

service time and freight. Please consult your dealer for more details.

If you think you have a defective product, follow these steps:

1. Collect all the information about the problem encountered. (For example, CPU

speed, Advantech products used, other hardware and software used, etc.) Note

anything abnormal and list any onscreen messages you get when the problem

occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain an RMA (return merchandise

authorization) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a fully-completed Repair and Replacement

Order Card and a photocopy proof of purchase date (such as your sales receipt)

in a shippable container. A product returned without proof of the purchase date

is not eligible for warranty service.

5. Write the RMA number visibly on the outside of the package and ship it prepaid

to your dealer.

Part No. Edition 1

Printed in Taiwan October 2019

iii EPC-U2117 User Manual

Declaration of Conformity

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installa-

tion. This equipment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause harmful inter-

ference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interfer-

ence to radio or television reception, which can be determined by turning the equip-

ment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the fol-

lowing two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that

may cause undesired operation.

Warning! Any changes or modifications made to the equipment which are not

expressly approved by the relevant standards authority could void your

authority to operate the equipment.

Caution!

EPC-U2117 User Manual iv

Technical Support and Assistance

1. Visit the Advantech web site at www.advantech.com/support where you can find

the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

– Product name and serial number

– Description of your peripheral attachments

– Description of your software (operating system, version, application software,

etc.)

– A complete description of the problem

– The exact wording of any error messages

Warnings, Cautions and Notes

Packing List

Before installation, please ensure the following items have been shipped:

 1 x EPC-U2117 unit

 1 x China RoHS

Warning!

Warning! Warnings indicate conditions, which if not observed, can cause personal

injury!

Caution! Cautions are included to help you avoid damaging hardware or losing

data.

There is a danger of a new battery exploding if it is incorrectly installed.

Do not attempt to recharge, force open, or heat the battery. Replace the

battery only with the same or equivalent type recommended by the man-

ufacturer. Discard used batteries according to the manufacturer's

instructions.

Note! Notes provide optional additional information.

v EPC-U2117 User Manual

Ordering Information

*Optional Accessories

Power Cord

Mounting Kit

Antenna Cable

Antenna

Model Number Description

EPC-U2117E3W-03Y10 Intel Atom E3930 1.3GHz, 32GB eMMC, 4GB memory

Part Number Description

1700001524 Power Cable 3-pin 180cm, USA type (for AC adapter 96PSA-A36W12W7)

170203183C

Power Cable 3-pin 180cm, Europe type (for AC adapter 96PSA-

A36W12W7)

170203180A Power Cable 3-pin 180cm, UK type (for AC adapter 96PSA-A36W12W7)

1700008921 Power Cable 3-pin PSE Mark 183cm (for AC adapter 96PSA-A36W12W7)

1702002600 Power cable 3-pin 183 cm, USA type (for AC adapter 96PSA-A60W12W6)

1702002605

Power cable 3-pin 183 cm, Europe type (for AC adapter 96PSA-

A60W12W6)

1700018704 Power cable 3-pin 183 cm, UK type (for AC adapter 96PSA-A60W12W6)

1700000237 Power cable 3-pin 183 cm, PSE type (for AC adapter 96PSA-A60W12W6)

1700000596 Power cord, 3-pin power cord (CCC) (for AC adapter 96PSA-A60W12W6)

Part Number Description Note

EPC-BRKU-DR010 EPC-U2000 Din Rail mounting kit Din Rail and VESA Mount

Part Number Description Note

1750008653-01 Cable Ant. SMA/F-R-BH MHF4/113 BLK 200mm For WiFi

1750006009 Antenna Cable SMA (F) to MHF 1.32 25cm For LTE

Part Number Description Note

1750008717-01 Dipole Ant. D.B 2.4/5G WIFI 3dBi SMA/M-R BLK For WiFi

1750007990-01 Antenna 4G/LTE full band L=11 cm 50 Ohm For LTE

EPC-U2117 User Manual vi

Safety Instructions

1. Please read these safety instructions carefully.

2. Please keep this User’s Manual for later reference.

3. Please disconnect this equipment from AC outlet before cleaning. Use a damp

cloth. Don’t use liquid or sprayed detergent for cleaning. Use moisture sheet or

clothe for cleaning.

4. For pluggable equipment, the socket-outlet shall near the equipment and shall

be easily accessible.

5. Please keep this equipment from humidity.

6. Lay this equipment on a reliable surface when install. A drop or fall could cause

injury.

7. The openings on the enclosure are for air convection hence protecting the

equipment from overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source when connecting the equipment to

the power outlet.

9. Ensure to connect the power cord to a socket-outlet with earthing connection

10. Place the power cord such a way that people cannot step on it. Do not place

anything over the power cord.

11. All cautions and warnings on the equipment should be noted.

12. If the equipment is not used for long time, disconnect the equipment from mains

to avoid being damaged by transient over-voltage.

13. Never pour any liquid into ventilation openings; this could cause fire or electrical

shock.

14. Never open the equipment. For safety reasons, only qualified service personnel

should open the equipment.

15. Before any internal installation procedures are carried out on the system, make

sure the system is turned off and cooled down for 15 minutes. Failing to run off

the system before opening it can cause permanent damage to the system and

serious or fatal injury to the user.

16. If one of the following situations arises, get the equipment checked by service

personnel:

The power cord or plug is damaged.

Liquid has penetrated into the equipment.

The equipment has been exposed to moisture.

The equipment does not work well, or you cannot get it to work according to

the user's manual.

The equipment has been dropped and damaged.

The equipment has obvious signs of breakage.

17. Do not leave this equipment in an environment where the storage temperature

may go below -40° C (-40° F) or above 85° C (185° F). This could damage the

equipment. the equipment should be in a controlled environment.

18. Caution: Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer, discard used

batteries according to the manufacturer's instructions.

 Risk of explosion if the battery is replaced by an incorrect type

 Replacement of a BATTERY with an incorrect type that can defeat a SAFE-

GUARD (for example, in the case of some lithium BATTERY types);

 Disposal of a BATTERY into fire or a hot oven, or mechanically crushing or

cutting of a BATTERY, that can result in an EXPLOSION;

vii EPC-U2117 User Manual

 Leaving a BATTERY in an extremely high temperature surrounding environ-

ment that can result in an EXPLOSION or the leakage of flammable liquid or

gas;

 A BATTERY subjected to extremely low air pressure that may result in an

EXPLOSION or the leakage of flammable liquid or gas.

19. The sound pressure level at the operator's position according to IEC 704-1:1982

is no more than 70 dB (A).

20. RESTRICTED ACCESS AREA: The equipment should only be installed in a

Restricted Access Area.

21. This equipment is not suitable for use in locations where children are likely to be

present.

22. Suitable for installation in Information Technology Rooms in accordance with

Article 645 of the National Electrical Code and NFPA 75

23. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-

tech disclaims all responsibility for the accuracy of any statements contained

herein.

Instructions de sécurité

1. Veuillez lire attentivement ces instructions de sécurité.

2. Veuillez conserver ce manuel de l'utilisateur pour toute référence ultérieure.

3. Veuillez déconnecter cet équipement de la prise secteur avant le nettoyage, uti-

lisez un chiffon humide, n'utilisez pas de détergent liquide ou pulvérisé pour le

nettoyage, utilisez une feuille d'humidité ou un chiffon pour le nettoyer.

4. Pour les équipements enfichables, la prise de courant doit se trouver à proxim-

ité de l'équipement et doit être facilement accessible.

5. Veuillez garder cet équipement de l'humidité.

6. Posez cet équipement sur une surface fiable lorsqu'il est installé.

7. Les ouvertures de l'enceinte sont destinées à la convection de l'air et protègent

finalement l'équipement contre la surchauffe.

8. Assurez-vous de la tension de la source d'alimentation lorsque vous connectez

l'équipement à la prise secteur.

9. Assurez-vous de connecter le cordon d'alimentation à une prise de courant

avec connexion à la terre

10. Placez le cordon d'alimentation de manière à ce que les personnes ne puissent

pas marcher dessus. Ne placez rien sur le cordon d'alimentation.

11. Toutes les précautions et tous les avertissements sur l'équipement doivent être

notés.

12. Si l'appareil n'est pas utilisé pendant une longue période, débranchez-le du

secteur pour éviter d'être endommagé par une surtension transitoire.

13. Ne jamais verser de liquide dans les ouvertures de ventilation, cela pourrait pro-

voquer un incendie ou un choc électrique.

14. N'ouvrez jamais l'appareil.Pour des raisons de sécurité, seul le personnel de

maintenance qualifié doit ouvrir l'équipement.

15. Avant d'effectuer toute procédure d'installation interne sur le système, assurez-

vous que le système est éteint et refroidi pendant 15 minutes, sans quoi le sys-

tème risque d'être endommagé de manière permanente et de provoquer des

blessures graves ou mortelles. L'utilisateur

16. Si l'une des situations suivantes se présente, faites vérifier l'équipement par le

personnel de service:

 Le cordon d'alimentation ou la fiche est endommagé.

 Le liquide a pénétré dans l'équipement.

EPC-U2117 User Manual viii

 Equipment L'équipement a été exposé à l'humidité.

 Equipment L'équipement ne fonctionne pas bien ou vous ne pouvez pas le

faire fonctionner conformément au manuel de l'utilisateur.

 Equipment L'équipement est tombé et est endommagé.

 Equipment L'équipement présente des signes évidents de rupture.

17. Ne laissez pas cet appareil dans un environnement où la température de stock-

age peut être inférieure à -40 ° C (-40° F) ou supérieure à 85 ° C (185° F), ce qui

pourrait endommager l'équipement. Environnement contrôlé

18. Attention: Danger d'explosion si la batterie n'est pas remplacée correctement

Remplacez uniquement par un type identique ou équivalent recommandé par le

fabricant, jetez les piles usagées conformément aux instructions du fabricant.

 Risque d'explosion si la batterie est remplacée par un type incorrect

 Remplacement d'une BATTERIE par un type incorrect pouvant neutraliser un

SAFEGUARD (par exemple dans le cas de certains types de BATTERIE au

lithium);

 La mise au rebut d'une BATTERIE au feu ou dans un four chaud, ou le broy-

age ou la découpe mécanique d'une BATTERIE, pouvant entra?ner une

EXPLOSION;

 Laisser une BATTERIE dans un environnement extrêmement chaud pouvant

entraîner une EXPLOSION ou une fuite de liquide ou de gaz inflammable;

 Une BATTERIE </ RTI> est une pression d'air extrêmement basse qui peut

provoquer une EXPLOSION ou une fuite de liquide ou de gaz inflammable.

19. Le niveau de pression acoustique au poste de conduite conformément à la

norme CEI 704-1: 1982 ne dépasse pas 70 dB (A).

20. ZONE D'ACCÈS RESTREINTE: L'équipement ne doit être installé que dans

une zone d'accès restreint.

21. Cet équipement ne peut pas être utilisé dans des endroits où des enfants sont

susceptibles d'être présents.

22. Convient à une installation dans des salles informatiques conformément à l'arti-

cle 645 du Code national de l'électricité et à la norme NFPA 75

23. AVIS DE NON-RESPONSABILITÉ: Cet ensemble d'instructions est conforme à

la norme CEI 704-1. Advantech décline toute responsabilité concernant l'exacti-

tude des déclarations contenues dans ce document.

ix EPC-U2117 User Manual

Contents

Chapter 1 Introduction..........................................1

1.1 Overview ................................................................................................... 2

1.2 System Configuration................................................................................ 2

1.3 General Specifications .............................................................................. 3

1.3.1 Standard PC functions .................................................................. 3

1.3.2 Power environment ....................................................................... 3

1.4 Mechanical Specifications......................................................................... 4

1.4.1 Mechanical specifications (terminal)............................................. 4

1.5 Environmental Specifications .................................................................... 4

Chapter 2 Jumper and Connector List................5

2.1 Jumper and Connector List ....................................................................... 6

Figure 2.1 Top View..................................................................... 6

Figure 2.2 Bottom View ............................................................... 7

2.2 Connectors................................................................................................ 8

2.2.1 DC input connector (DCIN1) ......................................................... 8

2.2.2 High definition multimedia interface (HDMI1) ............................... 9

2.2.3 Display port (DP1)......................................................................... 9

2.2.4 HD analog audio interface (AUDIO1).......................................... 10

2.2.5 Single port RJ45 connector (LAN1) ............................................ 10

2.2.6 Dual port RJ45 connector (LAN12)............................................. 11

2.2.7 USB 3.0 connector (USB12) ....................................................... 11

2.2.8 USB 3.0 connector (USB34) ....................................................... 12

2.2.9 LVDS backlight inverter power header (INV1) ............................ 12

2.2.10 LVDS panel voltage selection header (JLVDS1) ........................ 13

2.2.11 LVDS panel header (LVDS_EDP1) ............................................ 13

2.2.12 MCU programming header (JCAN2)........................................... 14

2.2.13 CAN BUS header (CAN1)........................................................... 14

2.2.14 Low pin count header (LPC1) ..................................................... 14

2.2.15 SPI programming pin header (SPI_CN1).................................... 15

2.2.16 CMOS battery connector (BAT1) ................................................ 15

2.2.17 General purpose I/O pin header (GPIO1) ................................... 15

2.2.18 COMS mode selection (JCMOS1) .............................................. 16

2.2.19 AT/ATX mode selection (PSON1)............................................... 16

2.2.20 Serial bus header (JFP2)............................................................ 16

2.2.21 PWRBTN#/ RESET#/HDD LED/ power LED header(JFP1)....... 17

2.2.22 SATA power header (SATA_PWR1) .......................................... 17

2.2.23 SATA signal connector (SATA1)................................................. 17

2.2.24 COM port header(COM1) ........................................................... 18

2.2.25 COM port header (COM2) .......................................................... 18

2.2.26 MINIPCIE and mSATA connector (MINI-PCIE1) ....................... 19

2.2.27 Next generation form factor (M.2_1) ........................................... 21

2.2.28 CPU FAN connector (CPUFAN1) ............................................... 22

2.2.29 DDR3L SO-DIMM socket (DIMMA1) .......................................... 22

2.2.30 CPU-system on chip (SOC1) ...................................................... 22

2.2.31 BIOS flash (SPI1)........................................................................ 23

2.3 Jumper List.............................................................................................. 23

Chapter 3 Peripheral Installation .......................25

3.1 HDD Installation ...................................................................................... 26

3.2 Mini PCIe Module Installation.................................................................. 27

EPC-U2117 User Manual x

Chapter 4 BIOS Setup ........................................ 29

4.1 BIOS Setup ............................................................................................. 30

4.2 Entering Setup ........................................................................................ 31

4.2.1 Main setup .................................................................................. 31

4.2.2 Advanced BIOS features setup .................................................. 32

4.2.3 Chipset........................................................................................ 52

4.2.4 Security boot............................................................................... 59

4.2.5 Save & exit.................................................................................. 61

Chapter 1

1 Introduction

This chapter briefly introduces the

EP-U2117 product

EPC-U2117 User Manual 2

1.1 Overview

The Advantech EP-U2117 is a palm-sized system using the latest Intel Atom E3900

processor technology to deliver a 30% CPU performance enhancement and a 45%

graphics performance boost. EPC-U2117 is designed with dual display output, multi-

ple I/O, and wide ranging 12-24V DC power inputs. It targets smart vending

machines, digital signage, smart kiosks, and more. EPC-U2117 is compatible with

Microsoft Windows 10 IoT Enterprise and Linux OS. EPC-U2117 has Advantech's

WISE-PaaS DeviceOn intelligent software integrated for remote system monitoring

and management.

Benefits:

 Palm-size embedded system with CE/FCC/CCC/BSMI certification

 Fanless, wide-temperature operation with high performance and flexibility

 Supports 12V ~ 24V wide voltage DC input

 One-stop integrated solution: Integrated ultra compact motherboard, chassis

peripherals and software

 RS-232, RS-422/485, ccTalk, MDB, CANBus dedicated I/O design for smart

kiosks and vending machines

 Dimensions: 170 x 117 x 52.6 mm

1.2 System Configuration

The following diagram is a block drawing of the EP-U2117.

Intel N4200/

N3350/x7-E3950

processor

LPC

Super I/O Nuvoton

NCT6106D

Infineon TPM 1.2/2.0

(optional)

DDR3L 1866 MHz SO-DIMM

Channel A

DDR3L 1866 MHz SO-DIMM

Channel B

HDMI 1.4b

DP 1.2 (colay LVDS)

LVDS (colay DP)

VGA (colay eDP)

eDP (colay VGA, optional)

2 SATA ports (SATA2 colay mSATA)

600 MB/s

48-bit LVDS

USB 2.0

4 USB 3.0 port

BIOS

USB 3.0

Realtek Audio Codec

ALC888S

8 USB 2.0 ports

(USB910 & USB1112 is optional)

HD Audio

SPI

PS/2, WDT,

8-bit GPIO

GbE LAN2:

Realtek RTL8111G

Full-size MiniPCIe with

SIM card holder (co-lay mSATA)

PCIe x1

(PCIex1/USB signal)

SATA

PCIex1/USB)

PCIe x1

GbE LAN1:

Realtek RTL8111G

PCIe x1

M.2 E key (co-lay PCIex1)

PCIe x 1 slot

(colay M.2 E key)

5 RS-232, 1 RS-232/422/485

3 EPC-U2117 User Manual

Chapter 1 Introduction

I/O Placement

1.3 General Specifications

1.3.1 Standard PC functions

 Intel® Atom® E3900, series processor; low power, high performance

 Supports two gigabit Ethernet and one M.2 & one full size miniPCIE module for

Wi-Fi, 3G/LTE, mSATA modules

 Multiple I/O with 4 x USB 3.0 ports, RS-232 (optional for MDB) and ccTalk

(optional for RS422/RS485) ports for data communication

 Wide ranging power input supports -12~24V DC input for industry and transpor-

tation

 Palm-sized, with extended temperature support under -20 ~ 60 °C

 Supports Win10 Enterprise 64-bit, Linux OS

 Advantech WISE-PaaS/DeviceON SW built-in

 Certificated with AWS Greengrass & Microsoft Azure IoT Edge

1.3.2 Power environment

 Power adaptor: AC/DC

– Input voltage: 100 Vac ~ 240 Vac @ 50 - 60 Hz,1.5

– Output voltage: 12 V @ 3 A~24V @ 3A/4.6A

EPC-U2117 User Manual 4

1.4 Mechanical Specifications

1.4.1 Mechanical specifications (terminal)

 System Dimensions: 170 X 117 X 52.6 mm (6.69" X 4.6" X 2.07")

 Carton Dimensions: 290 (L) X 210 (W) X 175 (H) mm

 Gross Weight: 2.0 kg

 Net Weight: 1.8 kg

1.5 Environmental Specifications

Temperature & Humidity

 Operating Temperature: -20 ~ 60 °C (with RF module)

 Storage Temperature: -40~85° C

 Relative Humidity: 40 ~ 95% RH (Non-condensed)

Safety

 CE/CCC/BSMI

EMI

 FCC class B approved for USA, Canada, and EU

Vibration:

 With SSD: 3Grms, 60068-2-64, random, 5 ~ 500 Hz, 1 hr/axis

Chapter 2

2 Jumper and

Connector List

EPC-U2117 User Manual 6

2.1 Jumper and Connector List

Figure 2.1 Top View

(20)

(14)

(

17

)

(

18

)

(15)

(1)

(2)

(3)

(4)

(6) (5)

(7)

(8)

(9) (10) (11)

(12)

(13)

(16)

(19)

(21)

(

22

)

(

24

)

(

23

)

(

25

)

(

26

)

(27)

7 EPC-U2117 User Manual

Chapter 2 Jumper and Connector List

Figure 2.2 Bottom View

Connector and Header List:

(1) DC input connector (DCIN1)

(2) High definition multimedia interface (HDMI1)

(3) DisplayPort (DP1)

(4) HD analog audio interface (AUDIO1)

(5) Single port RJ45 connector (LAN1)

(6) Dual port RJ45 connector (LAN12)

(7) USB 3.0 connector (USB12)

(8) USB 3.0 connector (USB34)

(9) LVDS backlight inverter power header (INV1)

(10) LVDS panel voltage selection header (JLVDS1)

(11) LVDS panel header (LVDS_EDP1)

(12) MCU programming header(JCAN2)

(13) CAN BUS header (CAN1)

(14) Low pin count header (LPC1)

(15) SPI programming pin header (SPI_CN1)

(16) CMOS battery connector (BAT1)

(17) General purpose I/O pin header (GPIO1)

(18) COMS mode selection (JCMOS1)

(19) AT/ATX mode selection (PSON1)

(20) Serial bus header (JFP2)

(29)

(30)

(31)

(

28

)

EPC-U2117 User Manual 8

(21) PWRBTN#/ RESET#/HDD LED/ Power LED header (JFP1)

(22) SATA power header (SATA_PWR1)

(23) SATA signal connector (SATA1)

(24) COM port header (COM1)

(25) COM port header (COM2)

(26) MINIPCIE and mSATA connector (MINI-PCIE1)

(27) Next Generation form factor (M.2_1)

(28) CPU FAN connector (CPUFAN1)

(29) DDR3L SO-DIMM socket (DIMMA1)

(30) CPU-System on chip (SOC1)

(31) BIOS flash(SPI1)

2.2 Connectors

2.2.1 DC input connector (DCIN1)

Pin Signal

1 Power input

2 GND

3 GND

9 EPC-U2117 User Manual

Chapter 2 Jumper and Connector List

2.2.2 High definition multimedia interface (HDMI1)

2.2.3 Display port (DP1)

Pin Signal Pin Signal

1 HDMI1_Z_D2+ 11 GND

2 GND 12 HDMI1_Z_CLK-

3 HDMI1_Z_D2- 13 x

4 HDMI1_Z_D1+ 14 x

5 GND 15 HDMI1_SCL

6 HDMI1_Z_D1- 16 HDMI1_SDA

7 HDMI1_Z_D0+ 17 GND

8 GND 18 +V5_HDMI

9 HDMI1_Z_D0- 19 HDMI1_HPD

10 HDMI1_Z_CLK+

Pin Signal Pin Signal

1DP1_0+ 11GND

2 GND 12 DP1_3-

3 DP1_0- 13 DP1_AUX_EN#

4DP1_1+ 14GND

5 GND 15 DP1_AUX+

6DP1_1- 16GND

7 DP1_2+ 17 DP1_AUX-

8 GND 18 DP1_DP_HPD

9DP1_2- 19GND

10 DP1_3+ 20 +V3.3_DP1

EPC-U2117 User Manual 10

2.2.4 HD analog audio interface (AUDIO1)

2.2.5 Single port RJ45 connector (LAN1)

Pin Signal

1GND

2 Line_L

3 Detect

4 Line_R

5GND

Pin Signal Pin Signal

1 LAN1_MDI0+ 8 LAN1_MDI2-

2 LAN1_MDI0- 9 LAN1_MDI3+

3 LAN1_MDI1+ 10 LAN1_MDI3-

4 LAN1_MDI1- 11 LAN1_LED1_z_ACT#

5 LAN1_TCT_A 12 +V3.3_DUAL

6 LAN1_TCTG 13 LAN1_LED2_z_1G#

7 LAN1_MDI2+ 14 LAN1_LED0_z_100M#

La page est en cours de chargement...

Advantech EPC-U2117 Manuel utilisateur

Advantech EPC-U2117 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents