Honeywell TH4000 Le manuel du propriétaire

Operating

Manual

PRO TH4000 Series

Programmable Thermostat

69-1760EF-1

Read and save these instructions.

® U.S. Registered Trademark. Patents pending.

Quick Reference Card

Grasp and pull to see basic operating instructions at a glance.

This manual covers the following models:

TH4110D: For 1 Heat/1 Cool systems

TH4210D: For 2 Heat/1 Cool heat pump systems only

(Pull thermostat from wallplate and turn over to find model number.)

Need Help?

For assistance with this product please visit http://yourhome.honeywell.com

or call Honeywell Customer Care toll-free at 1-800-468-1502

CAUTION: EQUIPMENT DAMAGE HAZARD.

To prevent possible compressor damage, do not operate cooling system when outdoor

temperature is below 50°F (10°C).

1

About your new thermostat

Thermostat features ...................................2

Programming at a glance ..........................3

Quick reference to controls .......................4

Quick reference to display ........................5

Programming & Operation

Set time and day ........................................6

System switch (Heat/Cool) ........................7

Fan switch (Auto/On) .................................8

Using program schedules .........................9

Program schedule overrides ...................12

Adaptive Intelligent Recovery™ ..............14

Compressor protection ............................15

Appendices

Battery replacement ................................16

In case of difficulty...................................17

Customer assistance ...............................19

Accessories ..............................................19

5-year limited warranty ............................20

This thermostat is ready to go!

Your new thermostat is pre-programmed

and ready to go.

See page 3 to check settings.

Table of contents

PRO TH4110D / TH4210D

Operating Manual

About your new thermostat

Your new Honeywell thermostat has been designed to give you many years of reliable

service and easy-to-use, push-button climate control.

Features

• Separately programmable weekday/weekend schedules.

• One-touch temp control overrides program schedule at any time.

• Energy Star

®

compliant to greatly reduce your heating/cooling expenses.

• Large, clear, backlit display is easy to read.

• Displays both room temperature and temperature setting.

• Built-in compressor protection.

2

About your new thermostat

PRO TH4110D / TH4210D

3

Your new thermostat is pre-programmed. Just set the time and day. Then check the

settings below and change if needed:

1. Set time and day (required for proper operation) .........................See page 6

2. Select system setting: Preset to Off..................................................See page 7

3. Select fan setting: Preset to Auto ......................................................See page 8

4. Program schedules: Preset to energy-saving levels

(assumes you wake at 6 am, leave at 8 am, return

at 6 pm and sleep at 10 pm) ....................................................... See pages 11-13

ONE-TOUCH TEMP CONTROL: You can override the program schedule at any time,

and manually adjust the temperature (see pages 12-13).

This thermostat is ready to go!

Operating Manual

4

Temperature adjustment (see page 11-13)

Fan Switch (see page 8)

On: Fan runs continuously.

Auto: Fan runs only when heating

or cooling system is on.

Quick reference to controls

• Set: Press to set time/day/

schedule.

• Hold: Press to override

programmed temperature control.

• Run: Press to resume program

schedule.

System switch (see page 7)

• Cool: Cooling system control.

• Off: All systems off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary

Heat control. Compressor is

locked out. (Select models only.)

PRO TH4110D / TH4210D

5

Wake

Wed

Recovery

Em Aux

Heat On

Set To

Inside

AM

75

6

:

30

Replace Batt

Quick reference to display screen

Low battery warning

(see page 16)

Adaptive Intelligent Recovery

TM

(see page 14)

Temperature setting

(see pages 11-13)

System status

Cool on: Cooling

system is on.

Heat on: Heating

system is on.

Em: Emergency heat

is on.**

Aux: Auxiliary heat

is on.**

** Only for heat pumps with this

capability (select models only).

Current day/time (see page 6)

Current inside

temperature

Current program period

Wake/Leave/Return/Sleep

(see pages 9-10)

Operating Manual

6

1. Press the SET button, then press s or t

to set the clock time.

2. Press the SET button, then press s or t

to select the day of the week.

3. Press RUN to save & exit.

Note: If the display flashes Set Clock, the

thermostat will follow your settings for the

weekday “Wake” time period until you reset

the time and day.

Set the time and day

Press SET, then adjust time.

Press SET, then select current day.

Set

Clock

AM

6

:

30

Wed

Set Day

PRO TH4110D / TH4210D

7

The SYSTEM switch can be set to control

your heating or cooling system, depend-

ing on the season.

• Cool: Cooling system control.

• Off: All systems are off.

• Heat: Heating system control.

• Em Heat: Emergency & Auxiliary

Heat control. Compressor is locked

out. (Select models only.)

System switch

Set SYSTEM switch to control the

heating or cooling system.

CAUTION: EQUIPMENT DAMAGE

HAZARD. Do not operate cooling

system when outdoor temperature

is below 50°F (10°C).

Operating Manual

8

Fan switch

Set the FAN switch to Auto or On.

In “Auto” mode (the most commonly used

setting), the fan runs only when the heat-

ing or cooling system is on.

If set to “On,” the fan runs continuously.

Use this setting for improved air circula-

tion, or for more efficient air cleaning.

Set FAN switch to choose whether the fan

runs continuously or only as needed.

PRO TH4110D / TH4210D

9

It’s easy to program your system for maximum energy savings. You can program

four time periods each day, with different settings for weekdays and weekends.

Set to the time you awaken and the temperature you want

during the morning, until you leave for the day.

Set to the time you leave home and the temperature you want

while you are away (usually an energy-saving level).

Set to the time you return home and the temperature you

want during the evening, until bedtime.

Set to the time you go to bed and the temperature you want

overnight (usually an energy-saving level).

Save money by setting program schedules

WAKE

6:00 am

70

°

LEAVE

8:00 am

62

°

RETURN

6:00 pm

70

°

SLEEP

10:00 pm

62

°

Operating Manual

10

Wake

(6:00 am)

Leave

(8:00 am)

Return

(6:00 pm)

Sleep

(10:00 pm)

Cool (Mon-Fri)Heat (Mon-Fri) Heat (Sat-Sun) Cool (Sat-Sun)

70

°

75

°

70

°

75

°

62

°

83

°

62

°

[Or cancel period]

83

°

[Or cancel period]

70

°

75

°

70

°

[Or cancel period]

75

°

[Or cancel period]

62

°

78

°

62

°

78

°

This thermostat is pre-set to use Energy Star

®

program settings. We recommend

these settings, since they can reduce your heating/cooling expenses by as much as

33%. (See next page to adjust times and temperatures of each time period.)

Energy Star

®

settings for maximum cost savings

PRO TH4110D / TH4210D

11

To adjust program schedules

1. Press SET until Set Schedule is displayed.

2. Press s or t to set your weekday Wake

time (Mon-Fri), then press SET.

3. Press s or t to set the temperature for this

time period, then press SET.

4. Set time and temperature for the next time

period (Leave). Repeat steps 2 and 3 for each

weekday time period.

5. Press SET to set weekend time periods (Sat-

Sun), then press RUN to save & exit.

Note: Make sure the thermostat is set to the system

you want to program (Heat or Cool).

Note: To cancel an unwanted time period (except

Wake), press and hold s + HOLD for 4 seconds

while in the Set Schedule mode.

Press SET 3 times, then adjust time.

Press SET, then set desired temperature.

Wake

Set Schedule

MonTueWedThuFri

Heat

Set To

AM

75

6

:

30

Wake

Set Schedule

MonTueWedThuFri

Heat

Set To

AM

75

6

:

30

Operating Manual

12

Press s or t to immediately adjust the

temperature. This will temporarily override

the temperature setting for the current time

period.

The new temperature will be maintained

only until the next programmed time period

begins (see page 9). For example, if you

want to turn up the heat early in the morning,

it will automatically be lowered later, when

you leave for the day.

To cancel the temporary setting at any time,

press RUN.

Program schedule override (temporary)

Press to temporarily adjust temperature.

Press to resume program schedule.

Set To

AM

70

6

:

30

Temporary

Set To

AM

75

6

:

30

Note: Make sure the thermostat

is set to the system you want to

control (heat or cool).

PRO TH4110D / TH4210D

13

Note: Make sure the thermostat is set

to the system you want to control (heat

or cool).

Press to permanently adjust temperature.

Press HOLD to permanently adjust

the temperature. This will override

the temperature settings for all time

periods.

The “Hold” feature turns off the

program schedule and allows you to

adjust the thermostat manually, as

needed.

Whatever temperature you set will be

maintained 24 hours a day, until you

manually change it, or press RUN to

cancel “Hold” and resume the program

schedule.

Program schedule override (permanent)

Set To

AM

70

6

:

30

Hold

Set To

AM

75

6

:

30

Press to resume program schedule.

Operating Manual

14

Adaptive Intelligent Recovery eliminates guesswork when setting your schedule.

It allows the thermostat to “learn” how long your furnace and air conditioner take

to reach the temperature you want.

Just set your program schedule to the time you want the house to reach your desired

temperature. The thermostat then turns on the heating or cooling at just the right time

to reach your scheduled temperature at your scheduled time.

For example: Set the Wake time to 6 am and the temperature to 70°. The heat will

come on before 6 am, so the temperature is 70° by the time you wake at 6.

Adaptive Intelligent Recovery

TM

(AIR)

PRO TH4110D / TH4210D

15

Wake

Wed

Cool

On

Set ToInside

AM

75

6

:

30

This feature helps prevent damage to the

compressor in your air conditioning or heat

pump system.

Damage can occur if the compressor is

restarted too soon after shutdown. This fea-

ture forces the compressor to wait 5 minutes

before restarting.

During the wait time, the display will flash

the message Cool On (or Heat On if you have

a heat pump). When the safe wait time has

elapsed, the message stops flashing and the

compressor turns on.

Message flashes until safe restart

time has elapsed.

Built-in compressor protection

Operating Manual

16

About your new thermostat

Batteries are optional (for backup

power) if your thermostat was wired

to run on AC power when installed.

Install fresh batteries when the

REPLACE BATT warning begins flash-

ing. The warning flashes about two

months before the batteries are

depleted.

Replace batteries once a year, or

before leaving home for more than a

month. If batteries are inserted within

one minute, the time and day will not

have to be reset. All other settings are

permanently stored in memory, and

do not require battery power.

Pull at bottom to

remove thermostat

from wallplate.

Turn thermostat over,

insert fresh AA alkaline

batteries, then reinstall

thermostat.

Battery replacement

PRO TH4110D / TH4210D

17

If you have difficulty with your thermostat, please try the following suggestions.

Most problems can be corrected quickly and easily.

Display is blank • Check circuit breaker and reset if necessary.

• Make sure power switch at heating & cooling system is on.

• Make sure furnace door is closed securely.

• Make sure fresh AA alkaline batteries are correctly installed (see

page 16).

Heating or

cooling system

does not respond

• Set system switch to Heat (see page 7). Make sure the temperature is

set higher than the Inside temperature.

• Set system switch to Cool (see page 7). Make sure the temperature is

set lower than the Inside temperature.

• Wait 5 minutes for the system to respond.

In case of difficulty

Operating Manual

18

About your new thermostat

Temperature

settings do not

change

Make sure heating and cooling temperatures are set to acceptable ranges:

• Heat: 40° to 90°F (4.5° to 32°C).

• Cool: 50° to 99°F (10° to 37°C).

“Cool On” or

“Heat On” is

flashing

• Compressor protection feature is engaged. Wait 5 minutes for the system

to restart safely, without damage to the compressor (see page 15).

“Heat On” is not

displayed

• Set the System switch to Heat, and set the temperature level above the

current room temperature (see page 7).

“Cool On” is not

displayed

• Set the System switch to Cool, and set the temperature level below the

current room temperature (see page 7).

To restore

Energy Star

®

default settings

Follow these steps to restore Energy Star default settings (see page 10):

1. Press SET 3 times to display “Set Schedule.”

2. Press and hold SET and RUN at the same time for 4 seconds.

3. Press RUN.

In case of difficulty

La page charge ...

Honeywell TH4000 Le manuel du propriétaire

Honeywell TH4000 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents