Hunter Fan 82021 Le manuel du propriétaire

I n s t a l l a t i o n G u i d e

82021 Tribeca Bath Ventilator with Light

READ and SAVE THESE INSTRUCTIONS

42948-01 4/18/2007

ENGLISH

See page 2

ESPAÑOL

Vea la página 15

FRANCAIS

Voir la page 29

DISCONNECT

ELECTRIC

POWER SUPPLY

AND LOCK OUT

SERVICE PANEL

BEFORE

SERVICING UNIT

W A R N I N G

TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING:

1. For general ventilating use only. Do not use for

ventilating hazardous or explosive materials.

2. To avoid motor bearing damage and noisy/unbal-

anced impellers, keep drywall spray, construction

dust, etc. off power unit.

3. DO NOT install this product in a wall. This prod-

uct is designed for installation in ceilings up to a

12/12 pitch (45 degrees). Ductwork must point

upward.

4. Please read specification label on product for fur-

ther information and requirements.

PREVENTATIVE MAINTENANCE

A clean fan provides better service. Disconnect the power supply and clean the fan as listed below.

TO CLEAN GRILLE: Use a mild detergent, such as dishwashing liquid, and a soft cloth. DO NOT use abrasive

cloths, steel wool pads or scouring powders.

TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle. To remove motor plate, find the single tab on the

motor plate (located next to the receptacle). Push up rear motor plate tab while pushing out on the side of the

housing or insert a screwdriver into the slot in the housing (next to tab) and twist screwdriver. Gently vacuum

fan, motor and interior of housing.

METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED IN WATER.

MAINTENANCE

The motor is permanently lubricated and never needs oiling. If the motor bearings are making excessive or

unusual noises, replace the motor with the exact service motor. You should replace the impeller at the same

time.

C A U T I O N

W A R N I N G

1. Usethis unit only in a manner intended by the manu-

facturer. If you have questions, contact the manufac-

turer at the phone number or address listed in the

warranty.

2. Before installing, servicing, or cleaning the unit,

disconnect the power by turning o the circuit break-

ers to the outlet box and associated wall switch loca-

tion. If you cannot lock the circuit breakers in the o

position, securely attach a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done

by qualified person(s) in accordance with all applicable

codes and standards, including fire-rated construction

codes and standards.

4. When cutting or drilling into wall(s) or ceiling, do not

damage electrical wiring or other hidden utilities.

5. Ducted fans must always be vented to the outdoors.

Keep ducting as short and as straight as possible.

6. Acceptable for use over a bathtub or shower when

connected to a GFCI protected branch circuit.

7. Install fan at least 5 feet (1.52 m) above the floor.

8. Never place a switch where it can be reached from a

tub or shower.

9. This unit must be grounded.

42948-01 4/18/2007

2

1

Turn off the power source.

Tools Needed. (Not supplied.)

Estimated assembly time: 30 to 60 minutes

Before Installation

x2

3/8” Cable Connector

H

I

J

K

L

x4

*

NOTE:

Strain relief cable connector

must be installed. Not Included.

A

B

C

95261-01-000

74508-03-133

96382-01-262

75184-01-133

96456-01-444

M

75730-01-444

Extra Screws

x2

D

E

F

G

95047-05-000

75864-02-000

03242-07-133

Check all the parts.

If damaged, call

1-888-830-1326

for replacements.

2

E

I

Loosen screws.

NOTE: Remove all packing materials before installation.

42948-01 4/18/2007

Included.

3

5

4

7

G

8

F

Remove the motor/blower from the housing.

H

E

3

Remove the pre-loaded screw tip covers.

Remove the wiring cover screw.

6

Back out the pre-loaded screw tips until flush

with the side of the housing.

Remove the wiring cover.

Remove packing material.

42948-01 4/18/2007

4

9

E

Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and

secure with washer.

Position the correct depth mark at the bottom edge of the

joist based on the thickness of your sheetrock.

New Construction

10

B

C

Choose Installation Option

For New Construction go to step A11, page 5

For Existing Construction go to step B11, page 8

A11

E

5/8

1/2

5/8

1/2

A12

Screw pre-loaded screws into joist or framing.

42948-01 4/18/2007

5

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

A14

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

A13

Route wires through the strain relief.

Connect wires as shown.

0

A16

Connect 4” duct and vent to the outside. Tape joints.

If ducting does not fit securely, an adapter may need

to be purchased.

A15

E

F

G

Install the wiring cover plate. Make sure all

wiring connections are inside the box or under

the wiring cover plate.

42948-01 4/18/2007

6

A19

I

Secure the motor by tightening the 2 screws.

A20

Turn on the power source.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

0

A17

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched

between the motor and the housing.

0

H

A18

ON

OF

F

A21

Test the motor. If the motor does not run, check the plug

connection.

A22

C1

Go to step

on page 10

to attach grille.

42948-01 4/18/2007

7

EXISTING FAN

B11

E

B12

Existing Construction

B13

2

1

B14

Route wires through strain relief.

Remove an existing fan and check to make sure the open-

ing is large enough to accommodate the new motor hous-

ing (7 1/4”x 7 3/4”).

Move the housing into position above the ceiling.

Attach existing ducting to duct connector. Tape joints.

If ducting does not fit securely, an adapter may need to

be purchased.

E

B15

Screw pre-loaded screws into joist or framing.

42948-01 4/18/2007

8

A

3 Pin

2 Pin

Fan Motor

Light

Green

Black

White

Black

White

Bare Copper

Ground

B16

Main Switch 1 (AC In)

Switch 2 (AC In)

*Option Fan & Main Light Together

*Option

H

B18

H

B19

B20

I

Connect wires as shown.

Reinstall the motor by inserting the tabs and pushing up

into position. Make sure the wires are not pinched between

the motor and the housing.

Connect wiring harness. DO NOT ALLOW THE MOTOR TO

HANG FROM THE WIRING HARNESS.

Secure the motor by tightening the 2 screws.

F

B17

G

Install the wiring cover plate. Make sure all wiring

connections are inside the box or under the wiring cover

plate.

42948-01 4/18/2007

9

ON

OF

F

B22

B23

C1

Go to step

on page 10

to attach grille.

B21

Test the motor. If the motor does not run, check the plug

connection.

Turn on the power source.

Attaching the Grille

Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO

HANG FROM THE WIRING HARNESS.

K

C1

H

C2

J

42948-01 4/18/2007

10

NOTE: Remove plastic packaging material from glass dome.

Align glass dome and push up.

Install 2 Max 60 watt A-15 bulbs (Not Included).

M

C7

Screw finial into position.

C5

L

C6

Attach thumbscrews.

WARNING: To reduce the risk of electrical shock,

all 3 thumbscrews MUST be properly installed.

K

C4

Align posts 1, 2 and 3 (stamped into motor housing)

with posts 1, 2 and 3 (stamped into light fixture). Slide light

fixture over posts.

J

C3

42948-01 4/18/2007

11

Trouble Shooting

Problem: Fan does not come on.

Solution:

• Hunter Fan Bath Ventilators are extremely quiet. To conrm that the fan is running, place your hand near

the vents to feel the air movement.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Light does not come on.

Solution:

• Replace the light bulb with a new bulb.

• Turn power on, replace fuse, or reset breaker.

• Check all plug connections to be sure they are secure.

• Check the wiring to make sure it matches the wiring diagram.

Problem: Fan is noisy.

Solution:

• Check and tighten all fasteners.

• Check the glass to make sure it is secure.

• Check the apper to make sure it moves freely.

If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.

hunterfan.com.

42948-01 4/18/2007

12

Warranty

Hunter Fan Company

Bath Exhaust Fan

LIMITED WARRANTY

Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath

exhaust fan:

If any part of your Hunter bath exhaust fan (except for glass xtures and light bulbs) fails at any time within one year after

the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part

free of charge for parts and labor performed at our nearest service center or at our Service Department in Memphis, Ten-

nessee. After this one-year period, you will be responsible for all parts and labor costs for repairs on the bath exhaust fan

except for motor repairs as provided below.

If your Hunter bath exhaust fan motor fails at any time within ve years after the date of sale to you due to a defect in mate-

rial or workmanship, labor and materials to repair the defect will be provided free of charge at our nearest service center or

our Service Department in Memphis, Tennessee. If no replacement part can be provided, we will, at our option, either re-

fund the actual purchase price of your bath exhaust fan or provide a replacement free of charge. After this ve-year period,

you will be responsible for all parts and labor costs for repairs on all parts of the bath exhaust fan.

IF THE ORIGINAL USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN, THIS WARRANTY AND ANY IMPLIED WAR-

RANTY WHICH THEN REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES OR LIGHT BULBS

OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.

THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUD-

ING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN

RESPECT TO ANY HUNTER FAN BATH EXHAUST FAN MOTOR OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD OF

THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS OR OTHER PARTS.

This warranty is voided if your Hunter bath exhaust fan is not purchased and installed in the U.S.A. This warranty excludes

and does not cover defects, malfunctions or failures of any Hunter bath exhaust fan which were caused by repairs by

persons not authorized by us, use of parts or accessories not authorized by us, mishandling, improper installation, modica-

tions or damage to the Hunter bath exhaust fan while in your possession, or unreasonable use, including failure to provide

reasonable and necessary maintenance.

To obtain servicing, contact the nearest Hunter authorized service center of the Hunter Fan Company Service Depart-

ment, 2500 Frisco Avenue, Memphis, Tennessee 38114. Please contact us before shipping your bath exhaust fan to us. If we

authorize you to ship it to us, you will be responsible for all insurance and freight or other transportation charges to our

factory or service center. We will return your Hunter bath exhaust fan freight prepaid. Your Hunter bath exhaust fan should

be properly packed to avoid damage in transit since we will not be responsible for any such damage. Proof of purchase is re-

quired when requesting warranty service. The purchaser must present the sales receipt or other document that establishes

proof of purchase.

IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITA-

TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO YOU.

THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO

STATE

.

42948-01 4/18/2007

13

2500 Frisco Avenue, Memphis, Tennessee 38114

Printed in China

42948-01 4/18/2007

G u í a d e i n s t a l a c i ó n

Ventilador para baño Tribeca 82021 con luz

LEA y CONSERVE ESTAS INSTRUCCIONES

42948-02 4/18/2007

ESPAÑOL

15

16

42948-02 4/18/2007

DESCONECTE LA

ALIMENTACIÓN ELÉCTRICA Y

CIERRE EL PANEL

DE SERVICIO

ANTES DE DAR

MANTENIMIENTO

A LA UNIDAD

tc.Retire las cubiertas de las puntas de tornillo precargadas.

A D V E R T E N C I A

PARA REDUCIR EL RIESGO DE DESCARGA ELÉCTRICA O LESIONES, OBSERVE LO SIGUIENTE:

1. Sólo para uso de ventilación general. No lo utilice

para ventilar ambientes con materiales peligrosos o

explosivos.

2. Para evitar daños a los rodamientos del motor e

impulsores ruidosos o desbalanceados, mantenga la

unidad de potencia lejos de la aplicación de aerosol

para paneles de yeso (drywall), polvo de la con-

strucción, etc.

3. NO instale este producto en una pared. Este pro-

ducto está diseñado para instalarse en techos con

una inclinación de hasta 12/12 (45º). La red de duc-

tos debe dirigirse hacia arriba.

4. Vea más información y los requisitos en la etiqu

eta de especificación del producto.

MANTENIMIENTO PREVENTIVO

Un ventilador limpio proporciona mejor servicio. Desconecte la alimentación y limpie el ventilador como se indica a continu-

ación.

PARA LIMPIAR LA REJILLA: Use un detergente suave, como líquido para lavado de platos, y un paño suave. NO

emplee paños abrasivos, almohadillas de lana de acero ni polvos para fregar.

PARA LIMPIAR EL CONJUNTO DEL VENTILADOR: Desconecte el cordón del motor de la toma de corriente. Para

retirar la placa del motor, encuentre la pestaña en la placa (ubicada junto a la toma de corriente). Levante la

pestaña posterior de la placa del motor mientras empuja hacia afuera en el lado del alojamiento o introduzca un

destornillador en la ranura del alojamiento (junto a la pestaña) y gire el destornillador. Suavemente aspire el ven-

tilador, el motor y el interior del alojamiento.

LAS PARTES METÁLICAS ELÉCTRICAS NUNCA DEBEN SUMERGIRSE EN AGUA.

MANTENIMIENTO

El motor está lubricado permanentemente y no necesita ser engrasado. Si los rodamientos del motor hacen rui-

dos excesivos o inusuales, reemplace el motor con el motor de servicio exacto. Debe reemplazar el impulsor al

mismo tiempo.

PRECAUCIÓN

ADVERTENCIA

1. Utilice esta unidad sólo de la manera indicada por el fabri

cante. Si tiene alguna pregunta, contacte con el fabricante

en el teléfono o la dirección indicados en la garantía.

2. Antes de instalar, dar servicio o limpiar la unidad, desco-

necte la alimentación eléctrica apagando los interrup-

tores automáticos que alimentan la caja de salida y al

interruptor de pared respectivo. Si no puede bloquear los

interruptores automáticos en la posición de apagado, fije

firmemente una forma destacada de advertencia, como

una etiqueta de seguridad, en el tablero de servicio.

3. Los trabajos de instalación y cableado eléctrico deben ser

realizados por personas calificadas de acuerdo con todos

los códigos y las normas aplicables, incluyendo los códi-

gos y normas de construcción contra incendio.

4. Al cortar o taladrar en paredes o techo, no dañe el

cableado eléctrico u otros servicios no visibles.

5. Los ventiladores canalizados siempre deben descargar al

aire libre. Mantenga los ductos tan cortos y rectos como

sea posible.

6. Aceptable para uso sobre una bañera o ducha si se

conecta en un circuito derivado protegido por un inter

ruptor automático de falla a tierra (GFCI).

7. Instale el ventilador por lo menos a 5 pies (1.52 m) por

encima del piso.

8. Nunca coloque un interruptor donde pueda ser

alcanzado desde una tina o una ducha.

9. Esta unidad debe ponerse a tierra.

x2

H

I

J

K

L

x4

*

A

B

C

95261-01-000

74508-03-133

96382-01-262

75184-01-133

96456-01-444

M

75730-01-444

x2

D

Conector de cable de 3/8”

*

NOTA:

Debe estar instalado el manguito

de alivio de tensión del cable. No

incluido.

Tornillos adicionales

E

F

G

95047-05-000

75864-02-000

03242-07-133

17

1

2

E

I

42948-02 4/18/2007

Apague la fuente de alimentación.

Incluido

Herramientas necesarias (no suministradas)

Tiempo estimado de ensamblaje: entre 30 y 60 minutos

Antes de la instalación

Verique todos los

componentes. Si están dañados,

llame al 1-888-830-1326

para obtener un reemplazo.

Afloje los tornillos.

NOTA: Retire todo el material de embalaje antes de la instalación.

5

4

7

G

8

F

18

H

E

3

6

Retire el motor/soplador del alojamiento.

Retire las cubiertas de las puntas de tornillo precargadas.

Retire el tornillo de la cubierta del cableado.

Retire las puntas de tornillo precargadas hasta que estén a

nivel con el lado del alojamiento.

Retire la cubierta del cableado.

Retire el material de embalaje.

42948-02 4/18/2007

9

E

19

10

B

C

A11

E

5/8

1/2

5/8

1/2

A12

Retire el primer tapón metálico de acceso del cableado.

Utilice el segundo si es necesario.

Inserte el manguito de alivio de tensión (no se incluye) en

la caja y sujételo firmemente con una arandela.

Ubique la correcta marca de profundidad en el borde infe-

rior de la viga, según el espesor de su plancha de yeso.

Construcción nueva

Escoja la opción de instalación

Para construcción nueva vaya al paso A11, página 19

Para construcción existente vaya al paso B11, página 22

Instale los tornillos precargados en la viga o el marco.

42948-02 4/18/2007

A

Motor del ventilador

Luz

Verde

Negro Interruptor 2 (CA)

Negro Interruptor principal 1 (CA)

Blanco

Negro Luz

Blanco

Cobre desnudo

Tierra

A14

*Opción Ventilador y luz principal juntos

*Opción

Negro

3

pasadores

3

clavijas

2

pasadores

2

clavijas

A13

0

A16

20

A15

E

F

G

Tienda los cables a través del manguito de

alivio de tension.

Conecte un ducto de 4” y ventile hacia el exterior. Aplique

cinta a las uniones. Si el ducto no se ajusta firmemente,

puede ser necesario comprar un adaptador.

Instale la placa de cubierta del cableado. Asegúrese que

todas las conexiones de cableado estén dentro de la caja o

debajo de la placa de cubierta del cableado.

Conecte los alambres como se muestra.

42948-02 4/18/2007

La page est en cours de chargement...

Hunter Fan 82021 Le manuel du propriétaire

Hunter Fan 82021 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents