Samlexpower SEC-2440UL Le manuel du propriétaire

OWNER'S

MANUAL

Please read this

manual BEFORE

operating your

battery charger

Switch Mode,

Automatic, Lead

Acid Battery

Charger

MODELS:

SEC-1280UL

SEC-2440UL

2 | SAMLEX AMERICA INC.

OWNER'S MANUAL: Battery Chargers | Index

SECTION 1: Important Safety Precautions ...................................... 3

SECTION 2: Description & Features ................................................ 6

SECTION 3: Layout .........................................................................7

SECTION 4: Principles of Operation ...............................................8

SECTION 5: Protections ................................................................ 16

SECTION 6: Installation ................................................................18

SECTION 7: Preparing the Charger for Operation ........................20

SECTION 8: Operation ................................................................ 27

SECTION 9: Troubleshooting ........................................................ 29

SECTION 10: Internal Fuse Ratings .................................................30

SECTION 12: Specications ............................................................ 31

SECTION 13: Warranty ................................................................... 35

Disclaimer of Liability

UNLESS SPECIFICALLY AGREED TO IN WRITING, SAMLEX AMERICA INC.:

1. MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION

PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.

2. ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT,

INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF

ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USERS RISK.

Samlex America reserves the right to revise this document and to periodically make changes to the content

hereof without obligation or organization of such revisions or changes.

Copyright Notice/Notice of Copyright

document is prohibited without express written permission by Samlex America Inc.

2 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 3

SECTION 1 | Important Safety Precautions

SAVE THESE INSTRUCTIONS. This manual contains important safety and operating

instructions.

The following safety symbols will be used in this manual to highlight safety

and information:

WARNING!

Indicates possibility of physical harm to the user in case of non-compliance.

!

CAUTION!

Indicates possibility of damage to the equipment in case of non-compliance.

i

INFO

Indicates useful supplemental information.

Hazardous conditions may result if the charger is not installed or operated correctly.

Please read the following instructions to prevent personal injury or damage to the

charger.

1.1 BATTERY RELATED

• Working in the vicinity of a Lead-acid battery is dangerous. Batteries generate explo-

sive gases during normal battery operation. For this reason it is of the utmost impor-

tance that each time before using your charger, you read and follow the instructions

provided exactly.

• To reduce risk of battery explosion, follow these instructions and those marked on the

battery.

• Never smoke or allow an open spark or ame in the vicinity of the battery or engine.

• Use charger for charging a Lead-acid battery only. It is not intended to supply power

to an extra low voltage electrical system or to charge dry-cell batteries. Charging

dry-cell batteries may cause them to burst and cause injury to persons and damage to

property.

• Never charge a frozen battery

• If it is necessary to remove battery from vehicle to charge it, always remove grounded

terminal from battery rst. Make sure all accessories in the vehicle are off in order to

prevent an arc.

• Study all battery manufacturer's specic precautions such as removing or not remov-

ing cell caps while charging and recommended rates of charge.

4 | SAMLEX AMERICA INC.

• For a charger having an output voltage selector switch, refer to the car owner's

manual in order to determine the voltage of the battery and to make sure the output

voltage is set at the correct voltage. If an output voltage selector switch is not pro-

vided, do not use the battery chargner unless the battery voltage matches the output

voltage rating of the charger.

• Never place the charger directly above or below the battery being charged; gases or

uids from the battery will corrode and damage the charger. Locate the charger as far

away from the battery as DC cables permit

• Do not operate charger in a closed-in area or restrict ventilation in any way

• Connect and disconnect DC output clips only after setting any charger switches to the

off position and removing AC cord from the electric outlet. Never allow clips to touch

each other

• Follow these steps when battery is installed in vehicle. A spark near battery may cause

a battery explosion. To reduce risk of a spark near battery:

(i) Position AC and DC cords to reduce risk of damage by hood, door, or moving

engine part;

(ii) Stay clear of fan blades, belts, pulleys, and other parts that can cause injury to

persons;

(iii) Check polarity of battery posts. A Positive (POS, P, +) battery post usually has a

larger diameter than a Negative (NEG, N, –) post;

(iv) Determine which post of battery is grounded (connected) to the chassis. If Nega-

tive post is grounded to chassis (as in most vehicles), see item (v). If Positive post is

grounded to the chassis, see item (vi);

(v) For a Negative-grounded vehicle, connect the Positive (Red) clip from battery

charger to positive (POS, P, +) undergrounded post of battery. Connect the Nega-

tive (Black) clip to vehicle or engine block away from battery. Do not connect clip to

carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge metal

part of the frame or engine block.

(vi) For a Positive-grounded vehicle, connect the Negative (Black) clip from battery

charger to negative (NEG, N, –) ungrounded post of battery. Connect the Positive

(Red) clip to vehicle chassis or engine block away from battery. Do not connect

clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gauge

metal part of the frame or engine block;

(vii) Connect charger AC supply cord to electric outlet; and

(viii) When disconnecting charger, turn switches to off, disconnect AC cord, remove

clip from vehicle chassis, and then remove clip from battery terminal.

• Follow these steps when battery is outside vehicle. A spark near battery may cause a

battery explosion. To reduce risk of a spark near battery:

(i) Check polarity of battery posts. A Positive (POS, P, +) battery post usually has a

larger diameter than a Negative (NEG, N, –) post;

SECTION 1 | Important Safety Precautions

4 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 5

(ii) Attach at least a 60cm 6-gauge (AWG) insulated battery cable to a Negative (NEG,

N, –) battery post;

(iii) Connect the Positive (Red) charger clip to the positive (POS, P, +) post of battery;

(iv) Position yourself and the free end of cable as far away from battery as possible,

then connect the Negative (Black) charger clip to free end of cable;

(v) Do not face battery when making nal connection;

(vi) Connect charger AC supply cord to electrical outlet; and

(vii) When disconnecting charger, always do so in reverse sequence of connecting

procedure and break rst connection while standing as far away from battery as

practical

1.2 CHARGER RELATED

• The maximum Ah capacities of the batteries must be limited as follows:

- SEC-1280UL: 800 Ah

- SEC-2440UL: 400 Ah

• Do not operate the charger in a closed-in area or restrict ventilation in any way.

Install in a well ventilated, cool, dry place.

• The charger must not be operated in a damp or wet environment. When mounting

in a boat, make sure it is not subjected to bilge water splash.

• Do not block the ventilation openings / openings for the cooling fan. There should

be at least 6 inches clearance all around the unit.

• Installation and wiring must comply with the local and the National Electrical Codes. It

is recommended that installation may be carried out by a certied electrician.

• Wrong installation on a boat may lead to corrosion of the boat. It is recommended

that installation on the boat must be carried out by a boat electrician.

• Disconnect the AC input power to the charger before connecting / disconnecting the

batteries or other DC loads or when working on the charger.

• Disconnect the AC input power before changing the setting of the Dip Switches.

• The chassis of the charger is connected to the Earth Ground Pin of the power cord

plug. Ensure that the Earth Ground Pin of AC receptacle feeding the charger is

connected to Earth Ground.

• Do not use an adapter. If a grounding type of receptacle is not available, do not use

this charger until proper outlet is installed by a qualied electrician.

• Do not operate the charger if the power cord is damaged.

SECTION 1 | Important Safety Precautions

6 | SAMLEX AMERICA INC.

SECTION 2 | Description & Features

2.1 GENERAL INFORMATION

SEC-1280UL (for 12V batteries) and SEC-2440UL (for 24V batteries) are high current, tem-

perature compensated 3 Stage Chargers that deliver Bulk Stage Currents of 80A and 40A

respectively ensuring a very fast, safe and complete charging of Lead Acid batteries. These

chargers can also be used as a Power Supply (Section 8.3) or as a DC UPS (Section 8.4).

2.2 FEATURES

• State-of-the-art Switch Mode Technology for high efciency, light-weight and quiet

operation.

• User congurable AC input voltage – 120 VAC or 230 VAC, 50 / 60 Hz

• Automatic operation for all types of Lead Acid Batteries - Flooded, AGM or Gel Cell

• User selectable 2 or 3-Stage automatic charging algorithm with timed Absorption

Stage and temperature compensation ensures rapid, safe and full return of capacity

for stand-alone and loaded batteries.

• Ability to reduce maximum charging current to approximately 1/2 of the rated capac-

ity during “Half Power Mode”. This allows safe charging of lower capacity batteries.

• Includes a Battery Temperature Sensor allowing temperature compensated charging,

if required.

• 2 banks of batteries can be charged simultaneously without the use of an external

battery isolator. The charging current will be shared between the two banks depend-

ing upon the depth of discharge of the connected batteries.

• Voltmeter and Ammeter for monitoring

• Fan cooled - fan ON/OFF based on output current.

• Protections against short circuit, over current, reverse battery connection and

over-temperature.

• Can be used as a power supply or as a DC UPS (Uninterruptible Power Supply)

when used in conjunction with a battery.

• Optional Remote LED Panel Model 900-RC with 10 Meters of wire for remote

ON/OFF control and indication of charging status.

• Conforms to UL Standard 1564 and certied to CSA STD. C22.2 No.107-2

• EMI compliant to FCC Part 15(B), Class B

2.3 MAXIMUM Ah CAPACITY OF BATTERY TO BE CHARGED

If the chargers are used to charge very high capacity batteries, they will be forced to sup-

ply their maximum rated charging current for longer time than the designed limit and

hence, the components will be overstressed and are likely to fail prematurely. To prevent

premature failure, the maximum Ah capacities of the batteries must be limited as follows:

- SEC-1280UL: 800 Ah

- SEC-2440UL: 400 Ah

6 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 7

SECTION 3 | Layout

NOTE: Both SEC-1280UL and SEC-2440UL have the same layout and dimensions

4 5 6 7 8

3 2 1

9

1

0

11

OUTPUT SIDE

INPUT SIDE

14B14A

12

13

LEGEND

1. Output Connector: +, Bank 1

2. Output Connector: +, Bank 2

3. Output Connector: –, Common

4. Jack for Temperature Sensor Plug (14B)

5. Green LED: Indicates “Half Power

Mode” is ON

6. Jack for optional Remote LED

Panel Model No. 900-RC

7. DIP switches S1 to S4 for mode selection

8. Push Switch for Half Power Mode:

Pressed ON; Released OFF

9. Power ON/OFF switch

10. AC power cord with 15A NEMA5-20 Plug

11. Grill protected opening for

cooling fan

12. Voltmeter

13. Ammeter

14. Battery Temperature Sensor Model No. TF-500

with 5m cable

14A. Adhesive backed sensor (attach to battery

container wall)

14B. 3.5mm Plug (insert into Jack 4)

TOP VIEW

3

2

1

14

11

10

<

SEC-1280UL: 0-15V

SEC-2440UL: 0-30V

• Hole: 5/16” Dia.

• Set Screw:

5/16” x 24 TPI

<

SEC-1280UL: 0-80A

SEC-2440UL: 0-50A

NOTE: Meters shown are for SEC-1280UL

Fig. 3 Layout of SEC-1280UL and SEC-2440UL

8 | SAMLEX AMERICA INC.

SECTION 4 | Principles of Operation

i

INFO

For complete understanding of working of battery chargers, understanding of

operation of Lead Acid batteries is desirable.

For detailed information on construction, working and application of batteries,

please refer to White Paper titled "Batteries, Chargers and Alternators" at the

following link to Samlex America, Inc. website:

www.samlexamerica.com/support/whitepapers.aspx

4.1 SWITCH MODE POWER SUPPLY (SMPS) CHARGER

This unit is a Switched Mode Power Supply (SMPS) and charger that converts 120 / 230

VAC, 50 / 60 Hz to regulated DC voltages and limits the maximum output current equal

to the rated Bulk Stage Current (Current Limit Value) as shown in Table 4.1.

TABLE 4.1 CHARGING STAGE VOLTAGES AND CURRENTS

Model No.

Bulk Stage

Current

(Current

Limit Value)

Constant

Voltage in

Bulk Stage

Constant

Voltage in

Absorption

Stage

Constant

Voltage

in Float

Stage

Terminal

Voltage at

No Load

(See Table 4.2)

SEC-1280UL 80A 13.5 VDC

14.0 VDC or

14.4 VDC

13.5 VDC

13.7V to

13.8V

SEC-2440UL 40A 27 VDC

28 .0 VDC

or 28.8 VDC

27 VDC

27.2V to

27.3V

The specied output voltage of the charger during particular charging stage is held

constant till the Bulk Stage Current value is reached. When the battery or DC load tries

to draw current > the Bulk Stage Current value (80A for SEC-1280UL & 40A for SEC-

2440UL), the charger limits the current to the Bulk Stage Current value and the output

voltage of the charger drops and is no longer constant. When the charger is charging a

battery at current = the Bulk Stage Current, it will be in current limit condition and the

terminal voltage of the charger will drop but will be clamped to the actual lower intrin-

sic terminal voltage of the battery relative to its Stage of Charge at that time.

8 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 9

SECTION 4 | Principles of Operation

4.2 BATTERY IMPEDANCE AND CHARGING CURRENT

The internal impedance of a healthy battery is very low - in tens of milli Ohms. The

impedance is higher in discharged condition. Average impedance may be assumed as 20

milli Ohm or 0.02 Ohm.

When the charger is delivering a constant voltage under Absorption/ Float Stages (is

supplying current < its Bulk Stage Current value), the charging current drawn by the bat-

tery can be roughly calculated as follows:

Charging current = (Charger Voltage - Intrinsic battery voltage) ÷ Internal resistance (0.02 Ohm)

For example, when SEC-1280UL is in the Bulk Charge Stage 1 (Fig 4.1), its output voltage

is set at 13.5 VDC. When a battery discharged to say 10.5V is charged, it will try to draw

very large current = (13.5V - 10.5V) ÷ Internal resistance (0.02 Ω) = 150A. SEC-1280UL

will, however, limit this current to 80A.

4.3 CHARGING STAGES AND CHARGING CURVES

These chargers are designed to provide the following 3-Stage / 2-Stage charging algo-

rithms for Lead Acid Batteries (Flooded / AGM / Gel Cell types)

• 3-Stage Charging Algorithm: Bulk Stage " absorption Stage " Float Stage for Lead

Acid Batteries

• 2-Stage Charging Algorithm: Bulk Stage " Float Stage. When 2-Stage Charging

Algorithm is selected (Section 7.4), the Absorption Stage of the 3-Stage Charging

Algorithm is bypassed. This algorithm is suitable for operation as a Power Supply

(Section 8.3) or as a DC UPS (Uninterruptible Power Supply) in conjunction with a

battery (Section 8.4)

The type of Lead Acid Battery and the desired charging algorithm can be selected with

the help of DIP Switches S1 and S2 (7 in Fig 3). For details, please refer to Sections 7.4

Charging Curves for 3-Stage Charging Algorithm are given at Fig 4.1 for SEC-1280UL and

at Fig 4.2 for SEC-2440UL

Details of the 3 stages of charging operation are explained at Sections 4.3.1 to 4.3.3

10 | SAMLEX AMERICA INC.

SECTION 4 | Principles of Operation

(i) 4-Hr/ 8-Hr Timer runs out (Section 7.5) OR,

(ii) Current reduces to 10% of Bulk Stage

Current i.e. 8A+/-0.5A

NOTE: Please see “NOTES” for Fig 4.2

Voltage

curve

Voltage Curve shows voltage

at the Output Connectors

(Battery Connected)

Current Curve shows output

current

Current curve

80% of

current

capacity

of charger

(64 Amps)

Time, Hours

14.4V

13.5V

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

AMPS VOLTS

80A

64A

Stage 1

“Bulk Stage”

Stage 2 “Absorption Stage”

Start of Absorption Stage (See Section 4.3.2) and

Absorption Stage Timer (See Section 7.5)

Level

2

Stage 3

“Float Stage”

B1 C1

D1

E1

B2 C2 D2

E2

A1

A2

Level

1

100

80

60

40

20

10

Figure 4.1 Charging Curve - SEC-1280UL

28.8V

27V

30

28

26

24

22

20

18

16

14

12

10

8

6

4

2

0

B1 C1

D1

E1

B2 C2 D2

E2

40A

32A

A1

A2

Voltage

curve

Current curve

80% of

current

capacity

of charger

(32A)

AMPS VOLTS

Start of Absorption Stage (See Section 4.3.2) and

Absorption Stage Timer (See Section 7.5)

Voltage Curve shows voltage

at the Output Connectors

(Battery Connected)

Current Curve shows output

current

Time, Hours

NOTE: Please see “NOTES” for Fig 4.2

Stage 1

“Bulk Stage”

Stage 2 “Absorption Stage”

Level

2

Stage 3

“Float Stage”

Level

1

(i) 4-Hr/ 8-Hr Timer runs out (Section 7.5) OR,

(ii) Current reduces to 10% of Bulk Stage

Current i.e. 4A+/-0.5A

50

40

30

20

10

0

Fig. 4.2 Charging Curve for SEC-2440UL

10 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 11

SECTION 4 | Principles of Operation

NOTES FOR FIGS 4.1 & 4.2

Please note the following important information related to the Charging Curves

shown in Figs 4.1 and 4.2 above:

1. Terminal Voltage reading at charger Output Connectors on no load and on load:

(a) The Output Connectors of the charger consist of one common Negative Con-

nector (3, Fig 3) and two Red Positive Connectors (1, 2 in Fig 3) for charging

two banks of batteries. Each of the two Positive Connectors of the two banks

has Schottky Diodes in series for isolation. These isolating Schottky Diodes have

a current dependent forward voltage drop "Vf" ranging from 0.2 to 0.3V (at

0.1A) to 0.8V (at 80A). In addition, there will be additional forward drop "Vb"

across the bulk resistance of the Schottky Diodes and this drop will also increase

with increase in charging current. Please note that the forward voltage drops

"Vf" and "Vb" occur only when current ows through the Schottky Diode i.e.

when the charger is supplying current to the battery / load.

(b) The Float and Absorption voltages are tightly regulated before the isolating

Schottky Diodes. However, the voltages available at the terminals of the two

banks will vary with the value of the charging current because of the current

dependent forward voltage drop "Vf" and bulk resistance drop "Vb" of the

Schottky Diodes. The Float Voltage before the Schottky Diodes is, therefore,

set 0.2 to 0.3V higher to compensate for the forward drops during Float Stage

when the charging current would have dropped to less than 1A. Hence, the

output voltage at the Output Connectors of the two banks at no load (nothing

connected to the Connectors of the banks) will read 0.2 to 0.5V higher than the

Float Voltage of 13.5 / 27.0V because there is no forward voltage drop as there

is no current ow through the Schottky Diodes. The voltages are specied with

respect to charging / load current as follows:

Table 4.2 Terminal Voltages

Charging Stage Output Voltage Output Current

Absorption Stage - SEC-1280UL 14.4 / 14V for SEC-1280UL At 5A +/- 0.5A

Absorption Stage - SEC-2440UL 28.8 / 28V for SEC-2440UL At 3A +/- 0.5A

Float Stage - SEC-1280UL 13.5V At 0.1A

Float Stage - SEC-2440UL 27.0V At 0.1A

Open Circuit - SEC-1280UL 13.7 to 14.0V At 0A

Open Circuit - SEC-2440UL 27.2 to 27.5V At 0A

Bulk Stage - SEC-1280UL 13.5V (Internal voltage of charger) 70 - 80A

Bulk Stage - SEC-2440UL 27.0V (Internal voltage of charger) 35 - 40A

12 | SAMLEX AMERICA INC.

SECTION 4 | Principles of Operation

(c) Please also note that the output voltage at the two banks may differ between

0.2 to 0.8V depending upon the different values of the charging current being

delivered through each as a result of different values of voltage drops Vf and Vb

across the isolating Schottky Diodes.

2. Standard Temperature Conditions: The charging voltages shown pertain to bat-

tery electrolyte temperature of 77°F (25°C)

3. Charger / Battery Voltage / Current Values:

(a) During Constant Current "Stage 1 - Bulk Stage" (See Section 4.3.1), the output

voltage of the charger will be clamped to the actual battery voltage corre-

sponding to the intrinsic (internal) State of Charge of the battery. However,

during (i) Constant Voltage "Stage 2 - Absorption Stage" (Section 4.3.2) and (ii)

Constant Voltage "Stage 3 - Float Stage" (Section 4.3.3), the charger will output

constant voltage. During these stages, the intrinsic (internal) voltage of the bat-

tery will be lower than the rated Absorption and Float Voltages of the charger

and the charging current will taper down as the Stage of Charge of the battery

rises under constant voltage charging.

(b) The voltage curve shows the voltage at the charger Output Connectors, which

will be the same as the voltage at the battery terminals (assuming that there is

no voltage drop along the wires connecting the charger to the batteries)

(c) The Current Curve shows the current being drawn by the battery

4.3.1 Stage 1 - Bulk Stage

4.3.1.1 The Bulk Stage is a Constant Current Stage where the battery is charged at “Bulk

Stage Current” rating of (i) 80A for SEC-1280UL or, (ii) 40A for SEC-2440UL. During this

stage, the charger’s open circuit voltage will be (i) 13.5V for SEC-1280UL or, (ii) 27.0V for

SEC-2440UL. However, when discharged battery is connected and charging is initiated

under this stage, the terminal voltage of the charger will get clamped to the battery

voltage - see Section 4.3.1.2 for details.

4.3.1.2 Let us assume that SEC-1280UL is being used to charge a 12V battery bank that

has been discharged to 10.5V. When the charger is switched on, the 12V battery will

initially try to draw very large current = (13.5V - 10.5V) " Internal Resistance of dis-

charged battery (say 0.02 Ohm) = 150A. As the Bulk Current rating of SEC-1280UL is 80A,

the charger will enter current limit condition at 80A (Point A2 in Fig 4.1) and its voltage

will drop but will get clamped at the initial battery voltage of 10.5V (Point A1 in Fig 4.1).

The battery will start charging at constant current of 80A (Section A2-B2 in Fig 4.1) and

its intrinsic (internal) voltage will ramp up almost linearly (Section A1-B1 in Fig 4.1). When

the battery’s intrinsic voltage approaches 13.5V (Point B1 in Fig 4.1) and the current

drawn by the battery reduces to < 80A (Point B2 in Fig 4.1), the charger will exit Constant

Current Bulk Stage and enter Constant Voltage Absorption Stage described further at

Section 4.3.2.

12 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 13

SECTION 4 | Principles of Operation

4.3.1.3 Charging Characteristics during Bulk Stage

• Battery is charged at

constant current

equal to Bulk Stage Current rating of 80A

for SEC-1280UL and 40A for SEC-2440UL

• Battery voltage rises slowly and almost linearly till 13.5V for SEC-1280UL and till

27.0V for SEC-2440UL

• The entire charging current is used to convert (i) Lead Sulfate to Sponge Lead at

the Negative plates and (ii) Lead Sulfate to Lead Dioxide at the Positive plates

• There is minimal gassing and the charging efciency is high - around 91%

• The restored capacity in this stage is inversely proportional to the Charging Rate

(due to Peukert’s Effect). This means that as the charging rate is increased, the

capacity restored in this stage will also be reduced. This Bulk Stage will restore (i)

60% capacity at Charging Rate of C/5, (ii) 70%-75% capacity at Charging Rate of

C/10 and (iii) 85% to 90% capacity at Charging Rate of C/20

• Red LED marked "Bulk"/“I Phase” on the optional Remote Model 900-RC will be

lighted

4.3.2 Stage 2 - Absorption Stage

Refer to the Charging Curves at (i) Fig 4.1 for SEC-1280UL and (ii) Fig 4.2 for SEC-2440UL

4.3.2.1 General Information: The charger enters Absorption Stage at points “B1” (Voltage

Curve) and “B2” (Current Curve) after completion of Bulk Stage (Section 4.3.1). Absorption

Stage is carried out at constant voltage at 2 voltage levels - (i) Absorption Voltage Level 1

at 13.5V for SEC-1280UL or, 27.0V for SEC-2440UL and then, (ii) Absorption Voltage Level

2 at (i) 14.0/14.4 V for SEC-1280UL (selected through DIP Switches S1 and S2 - See Section

7.4 and Table 7.1) or, (ii) 28.0/28.8V for SEC-2440UL (selected through DIP Switches S1 and

S2 - See Section 7.4 and Table 7.2)

4.3.2.2 Absorption Stage Timer: When the charger enters Absorption Stage Level 1 (Sec-

tion 4.3.2.3.1), a 4 Hr / 8 Hr Absorption Stage Timer (Selected by DIP Switches “S3” and

“S4”- See Section 7.5, Table 7.3) is activated. When this Timer runs out, the charger will

transition from Absorption Stage to Float Stage (Section 4.3.3).

4.3.2.3.1 Absorption Stage Level 1: Charging is carried out at constant voltage of 13.5V

for SEC-1280UL or, 27.0V for SEC-2440UL (Section B1 to C1 of Voltage Curve in Figs 4.1

and 4.2). The intrinsic (internal) voltage of the battery rises further and its current starts

to taper down (Section B2 to C2 of Current Curve in Figs 4.1 and 4.2). The charging cur-

rent tapers down because the intrinsic (internal) battery voltage is rising and the differ-

ential voltage between 13.5/27.0V of the charger and the intrinsic (internal) voltage of

the battery is reducing, thereby, lesser current is driven into the battery. Tapering charge

at 13.5V / 27.0V is provided in this Absorption Stage Level 1 to reduce surface charge ef-

fect and to ensure that the charge slowly diffuses to the internal thickness of the plates

and prevents overcharging. When the charging current tapers down to 80% of the Bulk

Stage Current value of the charger (64A for SEC-1280UL or, 32A for SEC-2440UL) at point

14 | SAMLEX AMERICA INC.

“C2” (Current Curve in Figs 4.1 and 4.2), the charger transitions to Absorption Stage

Level 2 (See Section 4.3.2.3.2)

4.3.2.3.2 Absorption Stage Level 2: After completion of Absorption Stage Level 1 (Sec-

tion 4.3.2.3.1), the Absorption Voltage is raised to Level 2 as follows:

i. SEC-1280UL:

o Absorption Voltage is raised from 13.5V to 14.4 for Flooded /AGM or,

o Absorption Voltage is raised from 13.5V to 14.0 V for Gel Cell

NOTE: The desired voltage is selected through DIP Switches S1 and S2 (See Section 7.4

and Table 7.1).

ii. SEC-2440UL:

o Absorption Voltage is raised from 27.0V to 28.8V for Flooded /AGM or,

o Absorption Voltage is raised from 27.0V to 28.0 V for Gel Cell

NOTE: The desired voltage is selected through DIP Switches S1 and S2 (See Section

7.4 and Table 7.2).

At voltage transition point “C1” (Voltage Curve in Fig 4.1 and Fig 4.2), the internal out-

put voltage of the charger will be raised from (i) 13.5 V to 14.0 / 14.4V for SEC-1280UL

or, (ii) from 27.0V to 28.0 / 28.8V for SEC-2440UL.

However, this increased voltage will not be seen as constant voltage immediately

(Section C1 to D1 in Voltage Curves in Figs 4.1 and 4.2 shows voltage becomes constant

only after point D1) because the battery will try to draw current higher than the Bulk

Stage Current rating of the charger (80A for SEC-1280UL or, 40A for SEC-2440UL) due

to sudden rise in voltage of the charger. The charger will deliver current limited to the

rated Bulk Stage Current (Section “C2-D2” in the Current Curves in Figs 4.1 and 4.2),

its voltage will drop due to loss of regulation due to "current limit condition" and will

get clamped to the intrinsic (internal) battery voltage. The battery will start charging

further at the rated Bulk Stage Current (Section C2 to D2 in the Current Curves in Figs

4.1 and 4.2) and its voltage will start rising (Section C1 to D1 in Voltage Curves in Figs

4.1 and 4.2). At point “D2” (Current Curves in Figs 4.1 and 4.2), the charging current will

reduce to less than the Bulk Stage Current limit value of 80A for SEC-1280UL / 40A for

SEC-2440UL and the charger will then exit the current limited constant current mode

and will enter constant voltage mode of 14V/14.4 V for SEC-1280UL or, 28.0 / 28.8V for

SEC-2440UL. (Please note that voltage of 14V/14.4 V for SEC-1280UL or, 28.0 / 28.8V for

SEC-2440UL is the constant Absorption Voltage Level 2 being put out by the charger.

The intrinsic (internal) voltage of the battery will still be lower than these voltages

because the battery will still not be fully charged at this transition). As the intrinsic

(internal) voltage of the battery rises further, the charging current will start tapering

down (Section D2 to E2 in the Current Curves in Figs 4.1 and 4.2). Tapering charge is

provided at this transition to reduce surface charge effect to ensure that the charge

slowly diffuses to the internal thickness of the plates and prevents overcharging.

The charger will transition to the next “Stage 3- Float Stage” (Section 4.3.3) at point

“E2” (Current Curves in Figs 4.1 and 4.2) under the following 2 conditions (whichever

occurs earlier):

SECTION 4 | Principles of Operation

14 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 15

SECTION 4 | Principles of Operation

a) When the 4 Hr / 8 Hr Absorption Stage Timer (Selected by DIP Switches “S3” and

“S4”- See Section 7.5, Table 7.3) runs out OR,

b) When the charging current tapers down to 10% of the rated “Bulk Current Capac-

ity” of the charger;

• 8A +/- 0.5A for SEC-1280UL

• 4A +/- 0.5A for SEC-2440UL

4.3.2.3.3 Thresholds of Charger Currents for Change over Between Absorption and

Float Stages: The thresholds of charger current for change over between the Absorption

Stage (Displayed as "Absorption"/“U0 Phase" in optional Remote Control 900-RC) and

Float Stage (Displayed as "Float"/“U Phase" in optional Remote Control 900-RC) are

shown below:

Change Over SEC-1280UL SEC-2440UL

From Absorption Stage (Level 2) to Float Stage 8A +/- 0.5A 4A +/- 0.5A

From Float Stage to Absorption Stage (Level 1) 15A +/- 0.5A 8A +/- 0.5A

4.3.2.3.4 Charging Characteristics during Absorption Stage

• Absorption Stage Levels 1 and 2 (Displayed as "Absorption"/“U0 Phase" in op-

tional Remote Control 900-RC) feed additional 35% to 55% of the capacity that

adds to the total charged capacity of around 115% to take care of around 15%

loss due to charger efciency

• There will be moderate gassing during this Absorption Stage

• Orange LED marked "Absorption"/“U0 Phase” on the optional Remote Control

Model No.900-RC will be lighted

4.3.2.4 Thresholds of Charger Currents for Change over Between Absorption and Float

Stages: The thresholds of charger current for change over between the Absorption

Stage (Displayed as "Absorption"/“U0 Phase" in optional Remote Control 900-RC) and

Float Stage (Displayed as "Float"/“U Phase" in optional Remote Control 900-RC) are

shown below:

Change Over SEC-1280UL SEC-2440UL

From Absorption Stage (Level 2) to Float Stage 8A +/- 0.5A 4A +/- 0.5A

From Float Stage to Absorption Stage (Level 1) 15A +/- 0.5A 8A +/- 0.5A

4.3.3 Stage 3 - Float Stage

4.3.3.1 During this stage, the charger outputs a constant Float Voltage of (i) 13.5V for

SEC-1280UL or, (ii) 27.0V for SEC- 2440UL. This helps in maintaining full capacity of the bat-

tery and also provides replacement charge to overcome self discharge of the battery. The

battery can remain connected in this stage indenitely without the risk of discharging.

16 | SAMLEX AMERICA INC.

SECTION 4 | Principles of Operation

4.3.3.2 Charging characteristics during this stage are as follows:

• Float Stage is used to maintain the battery's charge without losing electrolyte

through gassing and also, to compensate for self-discharge. For example, a bat-

tery not under charge and sitting idle with no load will self discharge at around

1% of its remaining Ah capacity every day.

• Float Stage current is around 0.1% of the Ah capacity of the battery

• During this stage, Green LED marked "Float"/“U Phase" on the optional Remote

Control Model 900-RC will be lighted

4.3.3.3 Thresholds of Charger Currents for Change over Between Absorption and Float

Stages: The thresholds of charger current for change over between the Absorption

Stage (Displayed as “U0” Phase in optional Remote Control 900-RC) and Float Stage

(Displayed as “U” Phase in optional Remote Control 900-RC) are shown below:

Change Over SEC-1280UL SEC-2440UL

From Absorption Stage to Float Stage 8A +/- 0.5A 4A +/- 0.5A

From Float Stage to Absorption Stage 15A +/- 0.5A 8A +/- 0.5A

SECTION 5 | Protections

The charger has the following protections:

5.1 SHORT CIRCUIT SHUT DOWN

In case of a short circuit on the output side, the output of the charger will be shut down.

Another symptom of short circuit shut down is that the fan will be ON till the unit is

reset or switched OFF. On the optional Remote Control 900-RC, Green LED marked

"Power" and Red LED marked "Bulk"/ "I Phase" will be lit. The charger will be latched

in this shut down condition and will NOT recover automatically even after the short

circuit condition is removed. To reset, the AC input power ON/ OFF switch at the back of

the unit has to be switched OFF and ON again.

5.2 OVER LOAD CURRENT LIMITING

The current drawn by the load is automatically limited to a maximum of 80A for

SEC-1280UL (40A +/- 1A in “Half Power Mode”) and 40A for SEC-2440UL (20A +/- 1A

when in “Half Power Mode”). If the load tries to draw a higher current than these lim-

its, the output voltage of the unit will start to drop. The unit will automatically recover

when the overload condition is removed.

5.3 REVERSE BATTERY CONNECTION – DC SIDE FUSES WILL BLOW

The output is internally fused on the DC side - 3 x 30A fuses for SEC-1280UL and 3 X

15A fuses for SEC-2440UL. In case, the polarity of the battery connection is reversed, the

16 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 17

SECTION 5 | Protections

fuse(s) will blow. Another symptom of blown fuse on DC side is that the fan will be ON

till the unit is switched OFF. On the optional Remote Control 900-RC, Green LED marked

"Power" and Red LED marked "Bulk"/“I Phase" will be lit.

5.4 COOLING

The charger is cooled by convection and in addition, has a fan for forced air-cooling.

The operation of the fan is controlled by the current supplied by the charger and will be

switched ON and OFF automatically as follows:

SEC-1280UL SEC-2440UL

Switch ON current 15A +/- 1A 8A +/- 1A

Switch OFF current 8A +/- 0.5A 4A +/- 0.5A

NOTE: Once the fan switches on at the specied current threshold, it will switch off at

a lower threshold. For example, the fan in SEC-1280UL switches ON at 15A but switches

OFF at 8A. This is to prevent the fan from oscillating between ON and OFF conditions

due to minor uctuations in load current

5.5 OVER TEMPERATURE SHUTDOWN

!

CAUTION!

Keep the charger in a well ventilated, cool and open area. DO NOT BLOCK THE

VENT HOLES on the sides or the discharge openings of the cooling fan. Keep at

least 6” clearance on all sides

In case the fan fails or if the cooling is not adequate due to higher ambient tempera-

ture, inadequate air circulation or blockage of air ventilation openings, the temperature

inside the unit will rise. A temperature sensor is mounted in the windings of the power

transformer. At 105° C +/- 5° C the thermal sensor will activate and shut down the out-

put voltage of the charger. The fan will be ON. On the optional Remote Control

900-RC, Green LED marked "Power" and Red LED marked "Bulk"/"I Phase" will be lit.

The charger will be latched in this shut down condition and will NOT reset automatically

even after the unit has cooled down. To reset, the AC input power ON/OFF switch at the

back of the unit has to be switched OFF and ON again.

5.6 PROTECTION AGAINST TRANSIENTS / SURGES IN THE AC INPUT

In a number of locations, the AC line input is not clean and may contain high volt-

age transients / surges. To prevent damage to the internal components against these

unwanted high voltages, the charger uses a MOV (Metal Oxide Varistor) for protection.

If surge / transient voltage higher than approximately 170 VAC in 120V Mode / 340 VAC

in 230 VAC Mode appear in the AC input, the MOV will conduct and will blow the AC

side fuse.

18 | SAMLEX AMERICA INC.

SECTION 6 | Installation

6.1 INSTALLATION DIMENSIONS

Installation dimensions are given below. Dimensions are same for SEC-1280UL and

SEC-2440UL.

SEC-1280-2440UL Top View Dimensions

2

244

381

350

5

75

2

75

200

244

97

9

Fig. 6.1 Dimensional Drawing of SEC-1280UL & SEC-2440UL

18 | SAMLEX AMERICA INC. SAMLEX AMERICA INC. | 19

SECTION 6 | Installation

6.2 LOCATION, MOUNTING AND SAFETY

The charger is required to be installed in a safe, well ventilated and dry location.

Please see the details given under “Important Safety Precautions”. The charger can be

mounted horizontally or vertically. When mounting vertically on a wall or a bulkhead,

please ensure that the axis of the fan rotor is horizontal i.e. the fan exhaust opening

should face left or right but NOT face up or down.

WARNING!

Mounting the unit vertically on a vertical surface with the fan opening facing

up or down is NOT allowed for safety. This is to prevent falling of objects into

the unit through the fan grille when the fan opening faces up. If fan opening

faces down, hot damaged components may fall out.

6.3 OUTPUT CONNECTORS

Connectors with tubular, screw down type of terminals are used for output connection

(1,2 & 3 in Fig 3). The diameter of the tubular hole of the connector is 5/16". Set screw

size is 5/16" x 24 TPI. Two Positive output connectors (1, 2 in Fig 3) are provided for con-

necting to the Positive terminals of the 2 banks of batteries. One common connector (3

in Fig 3.1) is provided for the Negative connection.

6.4 TERMINAL LUGS FOR CONNECTION TO THE CHARGER

For rm connection when using stranded wire, crimp / solder “pin” style terminal lugs on

the charger end of the DC wires used for connecting to the battery / other DC loads. 3 pieces

of “pin” style terminal lugs have been provided as follows for charger to battery distance of

up to 10ft:

• For SEC-1280UL: 3 x Pin Type Terminal Lugs, Type PTNB 35-20. Will accommodate up to

AWG #4 wire

• For SEC-2440UL: 3 x Pin Type Terminal Lugs, Type PTNB 10-12. Will accommodate up to

AWG #8 wire

6.5 WIRES

To avoid polarity errors and possible damage, never use wires of only one color. Use Red

insulated wire(s) for Positive connection(s) and Black for Negative connection(s).

Recommended DC wire sizes are given below (Based on a voltage drop of 2%). The

length in feet is the length of the pair of the positive and negative DC wires from the

charger to the battery / other DC loads.

Distance From Battery SEC-1280UL SEC-2440UL

Up to 6 ft. AWG #2 AWG #8

6 to 10 ft AWG #1/0 AWG #6

10 to 20 ft. AWG #3/0 AWG #4

6.6 TERMINATION OF WIRE ENDS

For rm connection when using stranded wire, wire ends for the connection to the

charger should be terminated with pin types of lugs that have been provided (See Section 6.4).

20 | SAMLEX AMERICA INC.

7.1 SELECTING AC INPUT VOLTAGE

The charger is pre-set to operate from input AC voltage of 120 VAC, 60 Hz. To operate the

charger from AC input voltage of 230 VAC, 50 Hz, change the internal setting as follows:

1. Remove the side plate that has the power cord entry by unscrewing 4 screws

2. Remove the Voltmeter and the Ammeter on the top central plate by prying up the

bottom edges of the meters with a broad, at screw driver and by pushing the meters

up from the bottom of the plate (these are snap tted). Remove the connecting wires

and mark them. Note the polarity for connecting back in proper polarity. The meter

terminals are marked Positive (+) and Negative (-). Thicker wires are for the Ammeter

and thinner are for the Voltmeter

3. Gently slide the center top cover plate out. Note and mark its orientation for

correct re-tting

4. Locate Yellow loop of jumper wire with quick female disconnect. In the pre-set

120 VAC condition, this jumper wire is shorting the male vertical pins marked “C” and

“D” and “115V”. Pull any one end of this female disconnect upwards to disconnect

shorting between “C” and “D”. Insulate this end with insulating tape. The unit is now

set for “230 VAC”

5. The 120 VAC version has a soldered 20A fuse on the AC side. When converting

120 VAC version unit for 230 VAC operation, there is no need to replace the 20A fuse

6. Replace the AC plug of the power cord with a suitable 3 pin grounded plug to mate

with the 230 VAC outlet.

!

CAUTION!

The new plug should have 3 poles i.e. Line (L), Neutral (N) and Earth ground.

Color code for the power cord conductors is:

- Line (L) - Black

- Neutral (N) - White

- Earth ground - Green

7.2 CONNECTING BATTERIES OR OTHER DC LOADS

As shown in Fig. 7.1 and 7.2, the output of the charger has a common Negative (-) con-

nector and 2 Positive connectors for connection of 2 banks of batteries. Each Positive

connector has its own internal Isolating Diode, which works as a battery isolator. If more

than one bank of batteries is connected, these will be charged at the same time as long

as the AC power is available to the charger. The maximum charging current of 80A (Full

Power Mode)/ 40A (Half Power Mode) for SEC-1280UL and 40A (Full Power Mode)/ 20A

(Half Power Mode) current for SEC-2440UL will be shared among the connected banks

of the batteries depending upon their discharged states. In case the AC power fails or

if there is no output from the charger, the Isolating Diodes will prevent charging / dis-

charging among the batteries connected to the banks.

SECTION 7 | Preparing the Charger for Operation

La page charge ...

Samlexpower SEC-2440UL Le manuel du propriétaire

Samlexpower SEC-2440UL Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents