LG DLEX4200W Manuel utilisateur

Read this owner’s manual thoroughly before operating the appliance and keep it handy for

reference at all times.

OWNER'S MANUAL

DRYER

DLE3600*, DLG3601*

DLEX4000*, DLGX4001*

DLEX4200*, DLGX4201*

DLEX4500*, DLGX4501*

ENGLISH FRANÇAIS

MFL67652532

Rev.00_070820

www.lg.com

2

TABLE OF CONTENTS

3 PRODUCT FEATURES

4 SAFETY INSTRUCTIONS

5 IMPORTANT SAFETY INSTRUCTIONS

9 PRODUCT OVERVIEW

9 Parts

9 Accessories

10 INSTALLATION

10 Installation Overview

10 Product Specifications

11 Installation Location Requirements

12 Clearances

14 Leveling the Dryer

15 Reversing the Door

16 Installing the Side Vent Kit

17 Stacking the Dryer

18 Venting the Dryer

20 Connecting the Inlet Hose

(Steam Models)

21 Connecting Gas Dryers

23 Connecting Electric Dryers

24 Special Electrical Requirements

24 Final Installation Check

25 Installation Test (Duct Check)

27 OPERATION

27 Using the Dryer

28 Check the Lint Filter Before Every Load

28 Sorting Laundry

28 Loading the Dryer

29 Control Panel

32 Cycle Guide

36 Cycle Modifier Buttons

36 Option Buttons

37 Special Functions

37 Steam Functions

(Steam Models)

40 SMART FUNCTIONS

40 LG ThinQ Application

43 Smart Diagnosis™ Function

44 MAINTENANCE

44 Regular Cleaning

45 TROUBLESHOOTING

45 FAQs: Frequently Asked Questions

45 User Support Videos

46 Before Calling for Service

52 WARRANTY

3PRODUCT FEATURES

ENGLISH

PRODUCT FEATURES

Easy-to-Use Control Panel

Rotate the cycle selector knob to select the desired dry cycle. Add cycle options or adjust settings with the

touch of a button.

Easy-Access Reversible Door

The wide-opening door provides easy access for loading and unloading. The door hinge can be reversed to

adjust for installation location.

Steam Functions (Steam Models)

LG’s steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce

static, and make ironing easier. Simply select the Steam Fresh™ cycle, or you can add a Steam option to

selected cycles.

Flow Sense™ Duct Blockage Sensing System Indicator

The Flow Sense™ duct blockage sensing system detects and alerts you to restrictions in the installed

household ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the

ducts to remove the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying

times caused by blocked ducts.

Smart Diagnosis™

Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your

telephone to the Customer Information Center. The call center agent records the data transmitted from your

machine and uses it to analyze the issue, providing a fast and effective diagnosis.

LG ThinQ

Download the new LG smart phone app to set options, self-diagnose and troubleshoot problems with the

appliance, and other useful features. This function uses Wi-Fi.

C

E

R

T

I

F

I

E

D

E

S

I

G

N

4 SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and

tell you what may happen if the instructions are not followed.

WARNING- Risk of Fire

Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Clothes dryer installation must be performed by a qualified installer.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed,

it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.

Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct

clothes dryer airflow and increase the risk of fire.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Save these instructions.

WARNING

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property damage.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

• WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use any phone in your building.

- Clear the room, building or area of all occupants.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the fire department.

• Installation and service must be performed by a qualified installer, service agency or your gas supplier.

5SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of explosion, fire, death, electric shock, scalding or injury

to persons when using this product, follow basic precautions, including the

following:

INSTALLATION

• Before use, the appliance must be properly installed as described in this manual.

• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

• To reduce the risk of severe injury or death, follow all installation instructions.

• The appliance must be installed and electrically grounded by qualified service personnel in accordance with

local codes.

• Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.

• When moving or installing the product in a different location, call qualified service personnel for installation

and service.

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Moving or installation of the appliance requires two or more people.

• This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or aircraft.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions.

• This appliance must be positioned near to an electrical power supply.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.

• Do not install the appliance in humid spaces.

• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children might

use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.

• Adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety

glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is

installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with

clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These

conditions will obstruct clothes dryer airflow and increase the risk of fire.

6 SAFETY INSTRUCTIONS

• Place the dryer at least 18 inches above the floor for a garage installation.

• Do not use sheet metal screws or other fasteners which extend into the duct that could catch lint and reduce

the efficiency of the exhaust system. Secure all joints with duct tape.

• Use only rigid, semi-rigid or flexible metal 4-inch diameter duct inside the dryer cabinet or for exhausting to

the outside. Use of plastic or other combustible ductwork may cause a fire. Punctured ductwork may cause

a fire if it collapses or becomes otherwise restricted in use or during installation.

• The exhaust duct must be 4 inches (10.2 cm) in diameter with no obstructions. The exhaust duct should be

kept as short as possible. Make sure to clean any old ducts before installing your new dryer.

• Rigid, semi-rigid or flexible metal ducting is recommended for use between the dryer and the wall. All non-

rigid metal transition duct must be UL-listed. Use of other materials for transition duct could affect drying

time.

• Ductwork is not provided with the dryer, and you should obtain the necessary ductwork locally. The end cap

should have hinged dampers to prevent backdraft when the dryer is not in use.

• Gas dryers MUST be exhausted to the outside.

• The dryer exhaust system must be exhausted to the outside of the dwelling. If the dryer is not exhausted

outdoors, some fine lint and large amounts of moisture will be expelled into the laundry area. An

accumulation of lint in any area of the home may create a health and fire hazard.

• Do not install near another heat source such as a stove, oven or heater.

• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint,

dust, and dirt.

• The appliance must not be supplied through an external switching device, such as a timer, or connected to

a circuit that is regularly switched on and off by a utility.

OPERATION

• Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end.

• If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug it

immediately, and contact an LG Electronics customer information center.

• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out

from the outlet.

• Do not use an extension cord or adapter with this appliance.

• Do not grasp the power cord or touch the appliance controls with wet hands.

• Do not modify or extend the power cord.

• If the product has been submerged, contact an LG Electronics customer information center for instructions

before resuming use.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

• Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags, etc.),

gasoline, chemicals and other flammable vapors and liquids.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

7SAFETY INSTRUCTIONS

ENGLISH

• Read all instructions before using the appliance and save these instructions.

• Use this appliance only for its intended purpose.

• Do not abuse, sit on, or stand on the door of the appliance.

• Do not allow children to play on, in or with the appliance. Close supervision of children is necessary when

the appliance is used near children.

• Do not tamper with controls.

• In the event of a gas leak (propane gas, LP gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for

such a period, before using the appliance turn on all hot water faucets and let the water flow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or

use an open flame during this time.

• Fix the drain hose securely in place.

• Do not put oily or greasy clothing, candles or flammable materials on top of the appliance.

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

• Do not reach into the appliance if the drum is moving.

• Do not dry articles that have been previously cleaned in, washed in, soaked in, soiled with or spotted with

gasoline, dry cleaning solvents, vegetable oil, cooking oil or other flammable or explosive substances, as

they give off vapors that could ignite or explode.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Do not store plastic, paper, or clothing that may burn or melt on top of the dryer during operation.

• Always check the inside of the appliance for foreign objects.

• Gas appliances can cause minor exposure to four potentially hazardous substances, namely benzene,

carbon monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or

LP fuels.

• Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

To reduce the risk of fire due to contaminated loads, the final part of a tumble dryer cycle occurs without

heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items

are quickly removed and spread out so that the heat is dissipated.

• Do not let children or pets climb inside the dryer drum.

• Do not put living animals such as pets inside the product.

• Do not put any part of your body, such as your hands or feet, or metal objects under the product.

• Do not let your hand get pinched when opening or closing the dryer door.

STEAM (Steam Models)

• Do not open the dryer door during steam cycles.

• Do not touch the steam nozzle in the drum during or after a steam cycle.

8 SAFETY INSTRUCTIONS

MAINTENANCE

• Do not repair or replace any part of the appliance. All repairs and servicing must be performed by qualified

service personnel unless specifically recommended in this Owner’s Manual. Use only authorized factory

parts.

• Do not disassemble or repair the appliance by yourself.

• Remove any dust or foreign matter from the power plug pins.

• Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply.

• Remove the door before the appliance is removed from service or discarded to avoid the danger of children

or small animals getting trapped inside.

• Unplug the appliance before cleaning to avoid the risk of electric shock.

• Clean the lint filter before or after each load.

• The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

GROUNDING INSTRUCTIONS

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with

a qualified electrician or service personnel if you are in doubt whether the appliance is properly grounded.

Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by

a qualified electrician.

• The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. The appliance is equipped with

a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

• This dryer must be plugged into a properly grounded outlet. Electrical shock may result if the dryer is not

properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet

is properly grounded. Failure to follow these instructions may create an electric shock hazard and/or a fire

hazard.

WARNING

Fire Hazard

Failure to follow safety warnings exactly could result in serious injury, death or

property damage.

• Do not install a booster fan in the exhaust duct.

• Install all clothes dryers in accordance with the installation instructions of the manufacturer of the dryer.

SAVE THESE INSTRUCTIONS

9PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Parts

Control panel

Lint filter

Leveling feet

Reversible

door

Power Cord

(gas models)

Gas connection

(gas models)

Exhaust Duct Outlet

Terminal Block

Access Panel

(electric models)

Accessories

Included Accessories

NOTE

• For your safety and extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of unauthorized components or parts.

• The images in this manual may be different from the actual components and accessories which are subject to

change by the manufacturer without prior notice for product improvement purposes.

Optional Accessories

Y connector

(Steam Models)

Pedestal

(sold separately)

Stacking kit

(sold separately)

Side vent kit

(sold separately)

Kit No. 383EEL9001B

Drying Rack

(sold separately)

Hoses

(Steam Models)

10 INSTALLATION

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another

location.

Check and choose the

proper location

Level the dryer Vent the dryer

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Dryer Models

DLE3600*,

DLG3601*

DLEX4000*,

DLGX4001*

DLEX4200*,

DLGX4201*

DLEX4500*, DLGX4501*

Description

Non-steam

Dryer

Steam Dryer Steam Dryer

Electrical requirements Please refer to the rating label for detailed information.

Gas requirements

NG: 4 - 10.5-inch (10.2 - 26.7 cm) WC

LP: 8 - 13-inch (20.4 - 33.1 cm) WC

Dimensions

27” (W) X 30 1/8” (D) X 39” (H), 51 3/8” (D

with door open)

68.6 cm (W) X 76.5 cm (D) X 99 cm (H),

130.5 cm (D with door open)

27” (W) X 30” (D) X 39” (H), 51” (D with

door open)

68.6 cm (W) X 76.1 cm (D) X 99 cm (H),

129.7 cm (D with door open)

Net weight

Gas : 136.03 lb (61.7kg) - 139.34 lb (63.2kg)

Electric : 121.9 lb (55.3kg) - 125.3 lb (56.8kg)

Gas : 140.4 lb (63.7 kg)

Electric : 133.4 lb (60.5 kg)

Drying

capacity

Steam Cycle - IEC 7.4 cu.ft. (8 lb/3.6 kg)

Normal Cycle IEC 7.4 cu.ft. (22.5 lb/10.2 kg)

Connect the Electric dryerConnect the Gas dryerConnect the inlet hose

(steam models)

Test runInstallation test

Model numbers can be found on the cabinet inside the door.

NOTE

Electric dryerGas dryer

Plug in the power cord

DLE3600*, DLG3601*

DLEX4200*, DLGX4201*, DLEX4000*,

DLGX4001*, DLEX4500*, DLGX4501*

11INSTALLATION

ENGLISH

Installation Location Requirements

WARNING

• Read all installation instructions completely before installing and operating your dryer. It is important that

you review this entire manual before installing and using your dryer. Detailed instructions concerning

electrical connections, gas connections, and exhaust requirements are provided on the following pages.

WARNING

To reduce the risk of serious injury or death, follow basic precautions, including the following:

• Use long-sleeved gloves and safety glasses.

• The appliance is heavy. Two or more people are required when installing the dryer.

The installation requires:

• A location that allows for proper exhaust installation. A gas dryer must be exhausted to the outdoors. See

Venting the Dryer.

• A grounded electrical outlet located within 2 ft. (61 cm) of either side of the dryer. See Connecting Electric

Dryers.

• A sturdy floor to support the total dryer weight of 200 lb (90.7 kg). The combined weight of a companion

appliance should also be considered.

• No other fuel-burning appliance can be installed in the same closet as a dryer.

• Additional clearances might be required for wall, door and floor moldings.

• Companion appliance spacing should also be considered.

NOTE

• The floor must be level, with a maximum slope of 1 inch (2.5 cm) under the entire dryer. Clothes may not

tumble properly, and automatic sensor cycles may not operate correctly if the dryer is not level.

• For garage installation, you will need to place the dryer at least 18 inches (45.7 cm) above the floor. The

standard pedestal height is 15 inches (38 cm). You will need 18 inches (45.7 cm) from the garage floor to the

bottom of the dryer.

• Do not operate your dryer at temperatures below 45 °F (7 °C). At lower temperatures, the dryer might not shut

off at the end of an automatic cycle. This can result in longer drying times.

• The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

• Check code requirements that limit, or do not permit, installation of the dryer in garages, closets, mobile homes

or sleeping quarters. Contact your local building inspector.

12 INSTALLATION

Clearances

1"*

(25 mm)

14" max.*

(356 mm)

18" min.*

(457 mm)

14" max.*

(356 mm)

18" min.*

(457 mm)

30 - 30

1/8"

(761 - 765mm)

5"**

(127 mm)

1"*

(25 mm)

30 - 30

1/8"

(761 - 765mm)

5"**

(127 mm)

24 in.

2*

(

155 cm

2

)

2*

(310 cm

2

)

3"

*

(76 mm)

48 in.

3"

*

(76 mm)

1"

(25 mm)

1"

(25 mm)

27"

(686 mm)

0"

(0 mm)

39"

(990 mm)

1"

(25 mm)

1"

(25 mm)

27"

(686 mm)

Closet Door

Vent Requirements

Installation Spacing for Recessed Area or Closet Installation

The following clearances are recommended for this dryer. This dryer has been tested for clearances of 1 inch

(2.5 cm) on the sides and rear. Recommended clearances should be considered for the following reasons:

• Additional clearances should be considered for ease of installation and servicing.

• Additional clearances should be considered on all sides of the dryer to reduce noise transfer. For closet

installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered

doors with equivalent ventilation openings are acceptable.

Closet Ventilation Requirements

Closets with doors must have both an upper and lower vent to prevent heat and moisture buildup in the closet.

One upper vent opening with a minimum opening of 48 sq. in. (310 cm

2

) must be installed no lower than 6 feet

above the floor. One lower vent opening with a minimum opening of 24 sq. in. (155 cm

2

) must be installed no

more than one foot above the floor. Install vent grilles in the door or cut down the door at the top and bottom to

form openings. Louvered doors with equivalent ventilation openings are also acceptable.

NOTE

• There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of

vibration from one appliance to another. If there is enough vibration, it could cause appliances to make noise or

come into contact, causing paint damage and further increasing noise.

13INSTALLATION

ENGLISH

Installation Spacing for Recessed Area or Closet, with Stacked Washer and

Dryer

24 in.

2*

(155 cm

2

)

2*

(310 cm

2

)

48 in.

3"

*

(76 mm)

3"

*

(76 mm)

1"

*

(25 mm)

1"

(25 mm)

1"

(25 mm)

27"

(686 mm)

5 ½"

**

(140 mm)

6"

*

(152 mm)

77 ½"

(1968 mm)

* Required spacing

** For side or bottom venting, 2-inch (5.1 cm) of spacing is allowed.

Installation Spacing for Cabinet

For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.

* Required spacing

7" *

(178 mm)

7" *

(178 mm)

9" *

1"

(25 mm)

1"

(25 mm)

27"

(686 mm)

5"*

(127 mm)

1"*

(25 mm)

30 - 30 1/8"

(761 - 765mm)

(229 mm)

14 INSTALLATION

Leveling the Dryer

NOTE

• Adjust the leveling feet only as far as necessary

to level the dryer. Extending the leveling feet more

than necessary may cause the dryer to vibrate.

• To ensure that the dryer provides optimal drying

performance, it must be level. To minimize vibration,

noise, and unwanted movement, the floor must be a

perfectly level, solid surface.

1

Position the dryer in the final location. Place a

level across the top of the dryer.

Level

Leveling Feet

• All four leveling feet must rest solidly on the

floor. Gently push on the top corners of the

dryer to make sure that the dryer does not rock

from corner to corner.

NOTE

• If you are installing the dryer on the optional

pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet

should be fully retracted.

2

Use an adjustable wrench to turn the leveling

feet. Unscrew the legs to raise the dryer or

screw in the legs to lower it. Adjust the leveling

feet until the dryer is level from side to side and

front to back. Make sure that all four leveling feet

are in firm contact with the floor.

15INSTALLATION

ENGLISH

Reversing the Door

Tools Required

• Phillips screwdriver

• Large flat blade screwdriver (recommended for

hinge screws if they are tight or your Phillips

screwdriver is worn)

• Small flat blade screwdriver (for lifting out parts)

WARNING

To reduce the risk of damage to the dryer,

property damage or personal injury, follow

basic precautions, including the following:

• Support the door with a stool or box that fits

under the door, or have an assistant support the

weight of the door.

• Avoid dropping the door.

• Unplug the dryer or turn off power at the main

circuit breaker before beginning door reversal.

• Always reverse the door BEFORE stacking the

dryer on top of the washer.

Door Reversal Instructions

The instructions here are for changing the door swing

from a right to a left side hinge. If the door has been

reversed, and it is necessary to change it back, use

care when following these instructions. Some of

the illustrations and the left/right references will be

reversed, and you will need to read the instructions

carefully.

WARNING

• Be sure to support the weight of the door before

removing the hinge screws.

1

Open the door and remove the two decorative

screws, two latch screws, and the latch on the

catch side with a screwdriver. Save these for

step 4.

2

While supporting the door, remove the 2 screws

on the door hinge. Remove the door.

3

Turn the door upside down and line up the holes

in the hinge with the holes on the opposite side

of the cabinet. Reinstall the door with the screws

removed in step 2.

WARNING

• Be sure to support the weight of the door before

installing the hinge screws.

4

Install the two decorative screws, the latch,

and two latch screws removed in step 1 on the

opposite side from which they were removed.

5

Check that the door closes properly.

16 INSTALLATION

Installing the Side Vent Kit

WARNING

To reduce the risk of serious injury, death or

property damage, follow basic precautions,

including the following:

• Use long-sleeved gloves and safety glasses.

• Use a heavy metal vent.

• Do not use plastic or thin foil ducts.

• Clean old ducts before installing this dryer.

Your new dryer is configured to vent to the rear. It can

also vent to the bottom or side (right-side venting is

not available on gas models).

An adapter kit, part number 383EEL9001B, may be

purchased from your LG retailer. This kit contains

duct components necessary to change the dryer vent

location.

1

Remove the rear exhaust duct retaining screw.

Pull out the exhaust duct.

Retaining Screw

Rear Exhaust Duct

Option 1: Side Venting

2

Press the tabs on the knockout and carefully

remove the knockout for the desired vent

opening (right-side venting is not available on

gas models). Press the adapter duct onto the

blower housing and secure to the base of the

dryer as shown.

Adapter Duct

Bracket

Knockout

3

Preassemble a 4-inch (10.2 cm) elbow to the

next 4-inch (10.2 cm) duct section, and secure

all joints with duct tape. Be sure that the male

end of the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the

side opening and press it onto the adapter duct.

Secure it in place with duct tape. Be sure that

the male end of the duct protrudes 1.5 inches

(3.8 cm) to connect the remaining ductwork.

Attach the cover plate to the back of the dryer

with the included screw.

Cover Plate

Elbow

1½" (38 mm)

Option 2: Bottom Venting

2

Press the adapter duct onto the blower housing

and secure it to the base of the dryer as shown.

Adapter Duct

Bracket

3

Insert the 4-inch (10.2 cm) elbow through the

rear opening and press it onto the adapter duct.

Be sure that the male end of the elbow faces

down through the hole in the bottom of the

dryer. Secure it in place with duct tape. Attach

the cover plate to the back of the dryer with the

included screw.

Cover Plate

Elbow

17INSTALLATION

ENGLISH

Stacking the Dryer

Stacking Kit Installation

This stacking kit includes:

• Two (2) side rails

• One (1) front rail

• Four (4) screws

Tools Needed for Installation:

• Phillips screwdriver

WARNING

To reduce the risk of electrical shock, fire,

explosion, property damage, serious injury or

death, follow basic precautions, including the

following:

• The weight of the dryer and the height of

installation make this stacking procedure too

risky for one person. Two or more people are

required when installing the stacking kit.

• Do not use the stacking kit with a gas dryer in

potentially unstable conditions such as a mobile

home.

• Place the washer on a solid, stable, level

floor capable of supporting the weight of both

appliances.

• Do not stack the washer on top of the dryer.

• If appliances are already installed, disconnect

them from all power, water, or gas lines and from

draining or venting connections.

To ensure safe and secure installation, please

observe the following instructions.

1

Make sure the surface of the washer is clean

and dry. Remove paper backing from the tape

on one of the stacking kit side brackets.

2

Fit the side bracket to the side of the washer top

as shown in the below illustration. Firmly press

the adhesive area of the bracket to the washer

surface. Secure the side bracket to the washer

with a screw on the back side of the bracket.

Repeat steps 1 and 2 to attach the other side

bracket.

3

Place the dryer on top of the washer, fitting the

dryer feet into the side brackets as illustrated.

Avoid finger injuries; do not allow fingers to be

pinched between the washer and dryer.

Slowly slide the dryer toward the back of the

washer until the side bracket stoppers catch the

dryer feet.

4

Insert the front rail between the bottom of the

dryer and the top of the washer. Push the front

rail toward the back of the washer until it comes

in contact with the side rail stoppers.

Install the two remaining screws to secure the

front rail to the side rails.

18 INSTALLATION

Venting the Dryer

WARNING

To reduce the risk of fire or explosion, electric

shock, property damage, injury to persons or

death when using this appliance, follow basic

safety precautions, including the following:

• Do not crush or collapse ductwork.

• Do not allow ductwork to rest on or contact sharp

objects.

• If connecting to existing ductwork, make sure it is

suitable and clean before installing the dryer.

• Venting must conform to local building codes.

• Gas dryers MUST exhaust to the outdoors.

• Use only 4-inch (10.2 cm) rigid, semi-rigid or

flexible metal ductwork inside the dryer cabinet

and for venting outside.

• To reduce the risk of fire, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall, ceiling,

crawl space, chimney, gas vent, or concealed

space of a building.

• To reduce the risk of fire, DO NOT exhaust the

dryer with plastic or thin foil ducting.

• The exhaust duct must be 4-inch (10.2 cm) in

diameter with no obstructions. The exhaust duct

should be kept as short as possible. Make sure

to clean any old ducts before installing your new

dryer.

• Rigid, semi-rigid or flexible metal ducting is

recommended for use between the dryer and

the wall. All non-rigid metal transition duct must

be UL-listed. Use of other materials for transition

duct could affect drying time.

• DO NOT use sheet metal screws or other

fasteners which extend into the duct that could

catch lint and reduce the efficiency of the

exhaust system. Secure all joints with duct tape.

• Do not exceed the recommended duct length

limitations noted in the chart. Failure to follow

these instructions may result in extended drying

times, fire or death.

WARNING

• Ductwork is not provided with the dryer. You

should obtain the necessary ductwork locally.

The vent hood should have hinged dampers to

prevent backdraft when the dryer is not in use.

• The total length of flexible metal duct must not

exceed 8 ft. (2.4 m).

Ductwork

Wall Cap Type

Number

of 90°

Elbows

Maximum

length of 4-inch

diameter rigid

metal duct

Recommended

a

a: 4" (10.2 cm)

0 65 ft.(19.8 m)

1 55 ft.(16.8 m)

2 47 ft.(14.3 m)

3 36 ft.(11.0 m)

4 28 ft.(8.5 m)

Use only for short

run installations

b

b: 2.5" (6.35 cm)

0 55 ft.(16.8 m)

1 47 ft.(14.3 m)

2 41 ft.(12.5 m)

3 30 ft.(9.1 m)

4 22 ft.(6.7 m)

NOTE

• Deduct 6 ft. (1.8 m) for each additional elbow. Do

not use more than four 90° elbows.

• In Canada, only those foil-type flexible ducts, if any,

specifically identified for use with the appliance by

the manufacturer should be used. In the United

States, only those foil-type flexible ducts, if any,

specifically identified for use with the appliance by

the manufacturer and that comply with the Outline

for Clothes Dryer Transition Duct, Subject 2158A,

should be used.

19INSTALLATION

ENGLISH

Routing and Connecting Ductwork

NOTE

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork. Ductwork and

fittings are NOT included and must be purchased

separately.

• Use 4-inch (10.2 cm) diameter rigid, semi-rigid or

flexible metal ductwork.

• The exhaust duct run should be as short as

possible.

• Use as few elbow joints as possible.

• The male end of each section of exhaust duct must

point away from the dryer.

• Use duct tape on all duct joints.

• Insulate ductwork that runs through unheated areas

in order to reduce condensation and lint buildup on

duct surfaces.

• Incorrect or inadequate exhaust systems are not

covered by the dryer warranty. Dryer failures or

service required because of such exhaust systems

will not be covered by the dryer warranty.

Correct Venting

Incorrect Venting

20 INSTALLATION

Connecting the Inlet Hose

(Steam Models)

The dryer must be connected to the cold water tap using

the new water supply hose. Do not reuse old hoses.

1

Check the rubber seal at each end of the inlet hoses.

Two ru ber seals are supplied with each inlet hose.

They are used for preventing water leaks. Make sure

the connection to the cold water tap is tight.

2

Check the installation type.

Connect all water supply hoses tightly by hand

and then tighten another 2/3 turn with pliers.

WITH WASHER: When connecting the dryer to the

same faucet as a washer.

a. Shut off the cold water tap and remove the washer

hose.

b. Connect the short hose to the Y-connector using

one of the rubber seals.

c. Connect the other end of the short hose to the cold

water faucet.

d. Connect the long dryer hose to one side of the

Y-connector and connect the washer hose to the

other side.

Hose

connector

Rubber

seal

• Before connecting the water line to the dryer,

flush several gallons of water into a drain or

bucket. This will help prevent foreign particles

such as sand and scale from clogging the dryer

inlet valve.

• Do not overtighten. Damage to the coupling

may result.

NOTE

• Water supply pressure must be between 20

and 120 psi (138—827 kPa) .

• Do not strip or cross-thread when connecting

the inlet hose to the valve.

• If the water supply pressure is more than 800

kPa, a pressure-reducing valve should be

installed.

• Periodically check the condition of the hose

and replace the hose if necessary.

• Replace inlet hoses after 5 years of use to

reduce the risk of hose failure.

• Record hose installation or replacement dates

on the hoses for future reference.

Long

hose

Y-connector

WITH WASHER WITHOUT WASHER

Short

hose

WITHOUT WASHER: If the dryer does not share

the cold water tap with a washer.

a. Connect the straight end of the long hose to the

cold water faucet.

3

Connect the hose to the dryer. Connect the

water supply hose to the dryer inlet valve tightly

by hand and then tighten another 2/3 turn with

pliers.

Make sure that there are no kinks in the hoses

and that they are not crushed.

4

Turn on the cold water faucet.

5

Check for leaks at the Y-connector (if used) and

in all hoses.

NOTE

• If any leaks are found, shut off the water faucet,

remove the hose and check the condition of the

rubber seal.

NOTE

Y connector

La page charge ...

LG DLEX4200W Manuel utilisateur

LG DLEX4200W Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents