Sony HT-CT150HP Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur

Ce manuel convient également à

Home Theatre System
HT-CT150
4-174-097-13(1)
©2010 Sony Corporation
Operating Instructions
Mode d’emploi
Manual de instrucciones
GB
US
FR
ES
2
US
3
To reduce the risk of fire or electric
shock, do not expose this apparatus to
rain or moisture.
The unit is not disconnected from the AC power source
(mains) as long as it is connected to the wall outlet,
even if the unit itself has been turned off.
To reduce the risk of fire, do not cover the ventilation
opening of the apparatus with newspapers, tablecloths,
curtains, etc.
Do not place the naked flame sources such as lighted
candles on the apparatus.
To reduce the risk of fire or electric shock, do not
expose this apparatus to dripping or splashing, and do
not place objects filled with liquids, such as vases, on
the apparatus.
As the main plug is used to disconnect the unit from the
mains, connect the unit to an easily accessible AC
outlet. Should you notice an abnormality in the unit,
disconnect the main plug from the AC outlet
immediately.
Do not install the appliance in a confined space, such as
a bookcase or built-in cabinet.
Do not expose batteries or apparatus with battery-
installed to excessive heat such as sunshine, fire or the
like.
For the customers in the U.S.A
This symbol is intended to alert the user to
the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of
electric shock to persons.
This symbol is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Owner’s Record
The model and serial numbers are located at the rear of the
subwoofer. Record the serial numbers in the spaces
provided below. Refer to them whenever you call upon
your Sony dealer regarding this product.
Model No. HT-CT150
Serial No.
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13) Unplug this apparatus during lightning storms or
when unused for long periods of time.
WARNING
3
US
GB
US
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
The following FCC statement applies only to the
version of this model manufactured for sale in the
U.S.A. Other versions may not comply with FCC
technical regulations.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
CAUTION
You are cautioned that any changes or modifications
not expressly approved in this manual could void your
authority to operate this equipment.
On safety
• Should any solid object or liquid fall into the system,
unplug the system and have it checked by qualified
personnel before operating it any further.
• Do not climb on the subwoofer, as you may fall down
and injure yourself, or system damage may result.
On power sources
• Before operating the system, check that the operating
voltage is identical to your local power supply. The
operating voltage is indicated on the nameplate at the
rear of the subwoofer.
• If you are not going to use the system for a long time,
be sure to disconnect the system from the wall outlet
(mains). To disconnect the AC power cord (mains
lead), grasp the plug itself; never pull the cord.
• One blade of the plug is wider than the other for the
purpose of safety and will fit into the wall outlet
(mains) only one way. If you are unable to insert the
plug fully into the outlet, contact your dealer.
• AC power cord (mains lead) must be changed only at
the qualified service shop.
On heat buildup
Although the system heats up during operation, this is
not a malfunction. If you continuously use this system
at a large volume, the system temperature of the back
and bottom rises considerably. To avoid burning
yourself, do not touch the system.
On placement
Place the system in a location with adequate
ventilation to prevent heat buildup and prolong the
life of the system.
• Do not place the system near heat sources, or in a
place subject to direct sunlight, excessive dust, or
mechanical shock.
• Do not place anything at the rear of the subwoofer that
might block the ventilation holes and cause
malfunctions.
• Do not place the system near equipment such as a TV,
VCR, or tape deck. (If the system is being used in
combination with a TV, VCR, or tape deck, and is
placed too close to that equipment, noise may result,
and picture quality may suffer. This is especially
likely when using an indoor antenna. Therefore, we
recommend using an outdoor antenna.)
• Use caution when placing the system on surfaces that
have been specially treated (with wax, oil, polish, etc.)
as staining or discoloration of the surface may result.
Precautions
continued
4
US
• Take care to avoid any possible
injury on the corners of the
subwoofer.
On operation
Before connecting other components, be sure to turn off
and unplug the system.
If you encounter color irregularity on
a nearby TV screen
The system is magnetically shielded to allow it to be
installed near a TV set. However, color irregularities
may still be observed on certain types of TV sets.
If color irregularity is observed...
Turn off the TV set, then turn it on again after 15 to 30
minutes.
If color irregularity is observed
again...
Place the system further away from the TV set.
On cleaning
Clean the system with a soft dry cloth. Do not use any
type of abrasive pad, scouring powder or solvent such
as alcohol or benzine.
If you have any question or problem concerning your
system, please consult your nearest Sony dealer.
Copyrights
This system incorporates Dolby* Digital and Pro Logic
Surround and the DTS** Digital Surround System.
*
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
** Manufactured under license under U.S. Patent #'s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and the Symbol are
registered trademarks & DTS Digital Surround and
the DTS logos are trademarks of DTS, Inc. Product
includes software. © DTS, Inc. All Rights Reserved.
This system incorporates High-Definition Multimedia
Interface (HDMI™) technology.
HDMI, the HDMI Logo, and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
“BRAVIA Sync” is a trademark of Sony Corporation.
“PlayStation” is a registered trademark of Sony
Computer Entertainment Inc.
“x.v.Color” and “x.v.Color” logo are trademarks of
Sony Corporation.
ENERGY STAR
®
is a U.S.
registered mark.
As an ENERGY STAR
®
partner,
Sony Corporation has determined that
this product meets the ENERGY
STAR
®
guidelines for energy
efficiency.
5
US
Precautions ...............................................3
Getting Started
Unpacking ................................................6
Positioning the system .............................7
Connecting the speaker ............................9
Connecting the TV and player, etc. .......10
Connecting other components................12
Connecting the AC power cord (mains
lead) .................................................13
Setting up the sound output of the
connected component ......................13
Playback Options
Index to parts and controls.....................14
Enjoying TV...........................................16
Enjoying other components ...................17
Surround Function
Enjoying the surround effect..................19
“BRAVIA” Sync Features
What is “BRAVIA” Sync?.....................20
Preparing for “BRAVIA” Sync .............20
Enjoying Blu-ray Disc/DVD..................21
(One-Touch Play)
Enjoying the TV sound from the
system ..............................................22
(System Audio Control)
Turning off the system, TV and the
connected components.....................23
(System Power Off)
Using the power saving function ...........23
(HDMI SIGNAL PASS THRU)
Setting the Audio Return Channel function
to off ................................................24
Advanced Settings
Controlling connected Sony components
with the remote ................................25
Changing the input button assignments of
the remote ........................................28
Settings and adjustments using the
amplifier menu.................................30
Additional Information
Troubleshooting .................................... 34
Specifications ........................................ 36
Index...................................................... 38
Table of contents
6
US
Inserting batteries into the remote
Insert two R6 (size AA) batteries (supplied) by matching the 3 and # ends on the batteries to the
markings inside the compartment. To use the remote, point it at the remote sensor in the front panel
display of the subwoofer.
• Do not leave the remote in an extremely hot or humid place.
• Do not use a new battery with an old one.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct sunlight or lighting apparatus. Doing so may cause a malfunction.
• If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Getting Started
Unpacking
Subwoofer (SA-WCT150) (1)
Speaker (SS-CT150) (1)
Speaker cord (1)
Digital optical cord for a TV
(2.5 m) (1)
Remote commander (RM-
AAU072) (1)
R6 (size AA) batteries (2)
Warranty (1)
Operating Instructions (1)
Notes
Getting Started
7
US
Connecting the speaker cord to the speaker
The connectors of the speaker cord are color-coded depending on the type of speaker. Connect the
connectors of the speaker cord to match the color of the speaker jacks.
• When you install the speaker on a wall, be careful not to stumble over the cord connected to the speaker.
Positioning the system
Note
R CENTER L
Green
White
Red
A Speaker cord
(supplied)
A
Rear of the speaker
continued
8
US
Installing the speaker on a wall
You can install the speaker on the wall.
• Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach
the screws securely to a wall beam. Install the speaker on a vertical and flat reinforced area of the wall.
• Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety
during the installation.
• Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength,
improper screw installation or natural calamity, etc.
1 Prepare screws (not supplied) that are suitable for the holes on the back of the speaker.
See the illustrations below.
2 Fasten the screws to the wall. The screws should protrude 6 to 7 mm (approx. 1/4
inches).
3 Hang the speaker onto the screws.
Align the holes on the back of the speaker to the screws, then hang the speaker onto the two screws.
Notes
Hole on the back of the speaker
4 mm (1/6 inches)
more than 25 mm (1 inch)
5mm
(1/5 inches)
10 mm
(2/5 inches)
265 mm
(10 2/5 inches)
6 to 7 mm
(approx. 1/4 inches)
Getting Started
9
US
The connectors of the speaker cord are color-coded depending on the type of speaker. Connect the
connectors of the speaker cord to match the color of the SPEAKERS jacks.
Connecting the speaker
SAT/CATV INBD INDVD IN
HDMI
DIGITALSPEAKERS
TV OUT
ARC
AUDIO IN
R
L
TV
AUDIO IN
SA-CD/CD
DMPORT
DC 5V
0.7A MAX
COAX IN
VIDEO
OPT IN
TVSAT/CATVR CENTER
ONLY FOR
SS-CT150
L
Green
Red White
Speaker
Rear of the
subwoofer
A
A Speaker cord (supplied)
10
US
Connect the TV and/or player, etc., with HDMI jacks to the system using an HDMI cable.
By connecting Sony “BRAVIA” Sync-compatible components using HDMI cables and by setting the
Control for HDMI function via the TV for each connected component, operation can be simplified. See
““BRAVIA” Sync Features” (page 20).
Connecting the TV and player, etc.
SAT/CATV INDVD IN BD IN
HDMI
DIGITALSPEAKERS
TV OUT
ARC
AUDIO IN
R
L
TV
AUDIO IN
SA-CD/CD
DMPORT
DC 5V
0.7A MAX
COAX IN
VIDEO
OPT IN
TVSAT/CATVR CENTER
ONLY FOR
SS-CT150
L
TV
HDMI IN
Digital Audio OUT
(optical)
HDMI cable
(not supplied)
Digital optical cord for a TV
(supplied)
Blu-ray Disc player, etc.
HDMI OUT
DVD player, etc.
HDMI cable
(not supplied)
HDMI OUT
HDMI cable
(not supplied)
HDMI OUT
Digital Audio OUT
(optical)
HDMI cable
(not supplied)
Digital optical cord
(not supplied)
Rear of the
subwoofer
Satellite tuner or cable television
tuner, etc., with an HDMI jack
Getting Started
11
US
• The system is compatible with the Audio Return Channel (ARC) function. If you connect the system to the ARC-
compatible TV’s HDMI jack via an HDMI cable, you do not need to connect the TV to the system with the digital
optical cord (page 24).
• You can see the letters “ARC” beside the TV’s HDMI jack if it is compatible with the ARC function. Even if you
connect an HDMI cable to the jack, if the HDMI input jack is not compatible with the ARC function, you cannot
use the ARC function.
• The ARC function is available only when Control for HDMI is set to on.
• Depending on the satellite tuner, multi-channel sound may not be output. In this case, connect a digital optical cord
in addition to an HDMI cable and set “INPUT MODE” to “OPT” in the AMP menu (page 32).
Connect a “PlayStation 3,” etc., to any available HDMI jack. All the HDMI jacks on the system function in the same
way.
• The HDMI jack connections have priority when you connect different components to the system using the INPUT
OPT/INPUT COAX and HDMI jacks.
• When connecting a TV that does not have a digital optical audio output jack, connect the TV to the system using
an analog audio cord (not supplied).
• Even if the system is turned off (active standby mode), the HDMI signal will be sent from the connected component
to the TV via the HDMI connection. You can enjoy image and sound from the component on the TV.
Notes on HDMI connections
Use a High Speed HDMI cable. If you use a Standard HDMI cable, 1080p, Deep Color, or 3D images
may not be displayed properly.
Sony recommends that you use an HDMI-authorized cable or Sony HDMI cable.
Check the setup of the connected component if an image is poor or the sound does not come out of a
component connected via the HDMI cable.
Audio signals (sampling frequency, bit length, etc.) transmitted from an HDMI jack may be
suppressed by the connected component.
Sound may be interrupted when the sampling frequency or the number of channels of audio output
signals from the playback component is switched.
When the connected component is not compatible with copyright protection technology (HDCP), the
image and/or the sound from the HDMI TV OUT jack may be distorted or may not be output.
In this case, check the specification of the connected component.
We do not recommend using an HDMI-DVI conversion cable.
When “TV,” “DMPORT,” “SA-CD/CD,” or “VIDEO” is selected for the input source of the system,
video signals via the HDMI input jack (BD, DVD, SAT/CATV) that was selected last time are output
from the HDMI TV OUT jack.
This system supports Deep Color, “x.v.Color,” and 3D transmission.
To enjoy 3D images, connect 3D-compatible TV and video components (Blu-ray Disc player, Blu-
ray Disc recorder, “PlayStation 3,” etc.) to the system using High Speed HDMI cables, put on 3D
glasses, and then play back 3D-compatible content.
Notes
Tip
12
US
When connecting components that do not have HDMI jacks, such as a “PlayStation 2,” a DVD player,
a satellite tuner, or a cable television tuner, etc., set “CTRL HDMI” to “OFF” in the AMP menu of the
system (page 21).
• Do not connect or disconnect the DIGITAL MEDIA PORT adapter while the system is turned on.
• When you connect the DIGITAL MEDIA PORT adapter, be sure the connector is inserted with the arrow mark
facing toward the arrow mark on the DMPORT jack. To detach the DIGITAL MEDIA PORT adapter, press and
hold A and then pull out the connector.
Connecting other components
Notes
SAT/CATV INBD INDVD IN
HDMI
DIGITALSPEAKERS
TV OUT
ARC
AUDIO IN
R
L
TV
AUDIO IN
SA-CD/CD
DMPORT
DC 5V
0.7A MAX
COAX IN
VIDEO
OPT IN
TVSAT/CATVR CENTER
ONLY FOR
SS-CT150
L
VIDEO OUT
VIDEO OUT
DVD player, etc.
Digital Audio OUT
(coaxial)
Digital coaxial cord
(not supplied)
Audio cord
(not supplied)
DIGITAL MEDIA
PORT adapter
Other audio components, etc.
Audio signal OUT
To the VIDEO IN of
the TV.
Digital Audio OUT
(optical)
Digital optical cord
(not supplied)
Rear of the
subwoofer
To the VIDEO IN of the TV.
Satellite tuner or cable
television tuner, etc.,
without an HDMI jack
A
Getting Started
13
US
Before connecting the AC power cord (mains lead) of the system to a wall outlet (mains), connect all
the other components and TV to the system.
• After connecting the AC power cord (mains lead), wait about 20 seconds before turning on the power by pressing
?/1.
• Connect the system to an easily accessible AC outlet (mains). Should you notice an abnormality in the system,
disconnect the main plug from the AC outlet (mains) immediately.
To enjoy sound in multi-channel format (DTS, Dolby Digital, multi-channel LPCM), you need to make
the audio output settings of the connected component. Set the connected component to output sound in
multi-channel format. For details on audio output settings, refer to the operating instructions supplied
with the connected component.
Connecting the AC power cord (mains lead)
Notes
Setting up the sound output of the connected component
14
US
For more information, see the pages indicated in parentheses.
Subwoofer
A ?/1 (on/standby)
B INPUT SELECTOR
Press to select the input source to play back.
Every time you press the button, the input
source changes cyclically as follows: TV t
BD t DVD t SAT/CATV t VIDEO
t SA-CD/CD t DMPORT t TV……
C VOLUME –
D VOLUME +
E Front panel display
Playback Options
Index to parts and controls
POWER/
ACTIVE STANDBY
INPUT
SELECTOR
VOLUME VOLUME
Top view
15
US
Playback Options
Front panel display (subwoofer)
A POWER/ACTIVE STANDBY indicator
Lights as follows:
Green: The system is turned on.
Amber: Only HDMI parts of the system
are on (The Control for HDMI
function is working).
No light: The system is turned off.
• The amber light turns off 30 seconds after you
turn off the TV. However, if you set “PASS
THRU” to “ON” in the AMP menu, the indicator
stays amber even if you turn off the TV.
B Audio format indicators
Light up according to the audio format that
is being input to the system.
D: Dolby Digital
PLII: Dolby Pro Logic II
LPCM: Linear PCM
DTS
C NIGHT (page 32)
Lights up in NIGHT MODE.
D SLEEP (page 33)
Flashes when the sleep timer is active.
E HDMI (page 10)
Lights up when HDMI components are
being used or when an ARC signal is being
input to the system while TV is selected as
the input source.
F COAX/OPT
Light up according to the cable which you
are using.
G MUTING
Lights up when the sound is turned off.
H Remote sensor
I Message display area
Displays volume, selected input source,
audio input signal, etc.
POWER/
ACTIVE STANDBY
Note
continued
16
US
Remote control
This section describes subwoofer and speaker
button operation. See page 25 for details on the
button operation of connected components.
Point the remote towards the remote sensor ( ) of the
subwoofer.
*The 5, N, AUDIO and SOUND FIELD + buttons
have a tactile dot. Use it as a guide during operation.
A ?/1 (on/standby)
B Input buttons
Press one of the buttons to select the
component you want to use.
C SLEEP
Press to turn off at a preset time when you
want to fall asleep listening to music. You
can preset the time in 10-minute increments.
D NIGHT MODE
Press to reproduce dialog clearly even at a
low volume level. This function is useful for
enjoying sound at night.
E AMP MENU (page 30)
F SOUND FIELD +/– (page 19)
G MUTING
H MASTER VOL +/–
Press to adjust the volume.
I C, X, x, c or
Press C, X, x or c to select the menu items.
Then press to enter the selection.
Note
Enjoying TV
?/1
MASTER
VOL +/–
TV
17
US
Playback Options
1 Turn on the TV and choose a program.
Refer to the operating instructions of your
TV for details.
2 Turn the system on.
3 Press TV on the remote.
4 Adjust the volume by pressing
MASTER VOL +/–.
• The sound may be output from the TV’s speaker. In
this case, turn the volume of the TV’s speaker down
to minimum.
If you are using “BRAVIA” Sync
(System Audio Control)
You do not need to perform steps 2 and 3 above.
When you turn on the TV, the system is also
turned on, and the input source changes
automatically. You can also adjust the system’s
volume using the TV’s remote. If you turn off the
system, sound is output from the TV’s speaker.
For details on setting “BRAVIA” Sync, see
“Preparing for “BRAVIA” Sync” (page 20).
• The system is not turned on when you turn the TV on
if sound was being output from the TV speakers the
last time the TV was turned off.
1 Play the connected component.
2
Turn on the system.
Tip
Tip
Enjoying other
components
?/1
MASTER
VOL +/–
Input
buttons
continued
18
US
3 Press the input buttons to display the
input source in the front panel display.
4 For video components, change the TV’s
input to the HDMI input you chose in
step 3.
For details, refer to the operating
instructions of your TV.
5 Adjust the volume by pressing
MASTER VOL +/–.
• The sound may be output from the TV’s speaker. In
this case, turn the volume of the TV’s speaker down
to minimum.
• Even if you playback Dolby True HD, Dolby Digital
Plus or DTS HD with a connected component
compatible with these sound formats, the system
accepts the signal as Dolby Digital or DTS. When you
playback these high-quality sound formats, set the
connected component to output the sound in multi-
channel PCM, if possible.
• When you connect the video output jack of the
DIGITAL MEDIA PORT adapter to the video input
jack of the TV, set “CTRL HDMI” to “OFF” in the
AMP menu of the system (page 21). The images of a
component connected to the DIGITAL MEDIA
PORT adapter will not be played on the TV if “CTRL
HDMI” is set to “ON.”
• To enjoy the sound of a component without
displaying the images when “CTRL HDMI” is set to
“ON,” turn off the TV first and then reset the power of
the system.
If you turn on the system first and then turn off the
TV, all components connected to the TV will be
turned off because of the Control for HDMI function.
If you are using “BRAVIA” Sync
(One-Touch Play)
You do not need to perform steps 2 to 4 above.
When you turn on the connected components,
the system and the TV are also turned on, and the
input source changes automatically. You can
also adjust the system’s volume using the TV’s
remote.
For details on setting “BRAVIA” Sync, see
“Preparing for “BRAVIA” Sync” (page 20).
• The system is not turned on when you turn the TV on
if sound was being output from the TV speakers the
last time the TV was turned off.
Input source Playable component
TV TV, etc. connected to the TV
jack
BD Blu-ray Disc player, etc.
connected to the BD jack
DVD DVD player, etc. connected to
the DVD jack
SAT/CATV Satellite tuner or cable
television tuner, etc. connected
to the SAT/CATV jack
VIDEO DVD player, etc. connected to
the DIGITAL COAX IN
VIDEO jack
SA-CD/CD CD player, etc. connected to the
SA-CD/CD AUDIO IN jack
DMPORT Portable audio player, etc.
connected to the DMPORT jack
Tips
Notes
Tip
19
US
Surround Function
Selecting the sound field
This system can create multi-channel surround
sound. You can select one of system’s optimized
pre-programmed sound fields.
Press SOUND FIELD +/–.
The present sound field appears in the front panel
display.
Each time you press SOUND FIELD +/–, the
display changes cyclically as follows:
STANDARD y MOVIE y DRAMA y
NEWS y SPORTS y GAME y MUSIC
y 2CH STEREO y P.AUDIO y
STANDARD …
Available sound fields
* These sound fields are not available when
“DMPORT” is selected by pressing INPUT
SELECTOR.
** “P.AUDIO” appears only when “DMPORT” is
selected.
You can set a different sound field for each input
source.
The sound field default setting for “DMPORT” is
“P.AUDIO,” and for other sources, “STANDARD.”
When “DMPORT” is selected by pressing INPUT
SELECTOR, the center speaker produces no sound.
Some speakers will not produce sound depending on
the input signal, such as monaural programs.
When “2CH STEREO” or “P.AUDIO” is selected,
the center speaker produces no sound.
If you press the THEATER button on a Sony TV
remote when “CTRL HDMI” is set to “ON,” the
sound field changes to “MOVIE” (some Sony TVs
excluded).
Surround Function
Enjoying the surround
effect
SOUND
FIELD +/
Sound field Effect
STANDARD* Suits various sources.
MOVIE* Recreates powerful and realistic
sound, along with clear dialog.
DRAMA* Suited for TV dramas.
NEWS* Produces the announcer’s voice
clearly.
SPORTS* Produces the play-by-play
commentary clearly and realistic
sound with surround effects, such as
cheering, etc.
GAME* Produces powerful and realistic
sound, suited for playing video
games.
MUSIC* Suited for music programs or music
videos on Blu-ray Discs/DVDs.
2CH STEREO Suited for music CDs.
P.AUDIO** Suited to replay portable audio
source.
Tips
20
US
By connecting Sony components that are
compatible with “BRAVIA” Sync via an HDMI
cable (not supplied), operation is simplified as
below:
One-Touch Play (page 21)
System Audio Control (page 22)
System Power Off (page 23)
“BRAVIA” Sync is compatible with Sony TVs,
Blu-Ray Disc/DVD players, AV amplifiers, etc.,
with the Control for HDMI function.
CONTROL FOR HDMI is a mutual control
function standard used by CEC (Consumer
Electronics Control) for HDMI (High-Definition
Multimedia Interface).
The Control for HDMI function will
not operate correctly in the
following cases:
When you connect the system to components
which do not correspond with the Control for
HDMI function.
When you connect the system and components
using other than an HDMI connection.
When you connect non-Sony components
which are compatible with the Control for
HDMI function.
We recommend that you connect products
featuring “BRAVIA” Sync to this system.
• Depending on the connected components, the Control
for HDMI function may not work. Refer to the
operating instructions of the components.
To use “BRAVIA” Sync, set the Control for
HDMI function to on for the connected
components.
When you connect a Sony TV with the Control
for HDMI function, the Control for HDMI
function for the system and the connected
components can be set simultaneously by setting
the Control for HDMI function of the TV.
1 Make sure that the system is connected
to the TV and the connected
components via HDMI cables (not
supplied).
2 Turn on the system, the TV and the
connected components.
3 Select the input of the system and the
HDMI input of the TV (SAT/CATV, DVD,
BD), so that an image from a connected
component is displayed.
“BRAVIA” Sync Features
What is “BRAVIA” Sync?
Note
Preparing for “BRAVIA”
Sync
?/1
AMP
MENU
C, X, x, c,
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124

Sony HT-CT150HP Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues