Blackstone 1891 22 Inch Griddle Le manuel du propriétaire

BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

SAFETY ALERT KEY

 DANGER

Indicates a hazardous situation

that, if not avoided, will result in

death or serious injury.

 CAUTION

Indicates a hazardous situation

that, if not avoided, could result

in minor or moderate injury.

 WARNING

Indicates a hazardous situation

that, if not avoided, could result

in death or serious injury.

NOTICE

Indicates information considered

important, but not hazard-

related (e.g. messages related to

property damage).

OWNER’S MANUAL

IMPORTANT:

This instruction manual contains important

information necessary for the proper assembly and safe

use of the appliance.

Read and follow all warnings and instructions before

assembling and using the appliance.

Follow all warnings and instructions when using

the appliance.

Keep this manual for future reference.

Installer/Assembler: Leave these instructions with the consumer.

For the latest version of this manual,

scan this code or visit

BlackstoneProducts.com/support

MODEL:  v13

22" GRIDDLE

WITH HOOD AND STAND

TABLE OF CONTENTS

IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . .

ACTIVATE YOUR WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

ASSEMBLY GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 

USING YOUR BLACKSTONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | IMPORTANT SAFETY INFORMATION

GAS APPLIANCE SAFETY

• The use of alcohol, prescription, or non-prescription drugs may

impair the consumer’s ability to properly assemble or safely

operate the appliance.

• Keep children and pets away from the appliance at all times.

• Have a type BC or ABC fire extinguisher readily available.

DO NOT USE FOR PURPOSES OTHER THAN INTENDED:

• DO NOT modify this appliance.

• DO NOT use for commercial cooking.

• DO NOT use this appliance as a heater.

THIS APPLIANCE SHALL BE USED OUTDOORS ONLY.

• DO NOT use this appliance inside buildings, garages, or any other

enclosed area.

• DO NOT install this appliance in or on a boat.

• DO NOT install this appliance in or on a recreational vehicle.

MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL:

• DO NOT use this appliance on or under any apartment or condo-

minium balcony or deck.

• DO NOT use this appliance under overhead combustible

construction.

• DO NOT obstruct the flow of combustion and ventilation air.

• DO NOT operate this appliance any closer than 36 in (1 m) from the

sides and back of the appliance.

A = 36" (1 m)

A

 WARNING

• DO NOT store or use gasoline or other flammable liquids

or vapors in the vicinity of this or any other appliance.

• An LPG cylinder not connected for use shall not be

stored in the vicinity of this or any other appliance.

 DANGER

• NEVER operate this appliance unattended.

• NEVER operate this appliance within 10 ft (3.0 m) of any

structure, combustible material or other gas cylinder.

• NEVER operate this appliance within 25 ft (7.5 m) of any

flammable liquid.

• If a fire should occur, keep away from the appliance and

immediately call your fire department. DO NOT attempt

to extinguish an oil or a grease fire with water.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

INSTALLATION MUST CONFORM WITH LOCAL CODES

In the absence of local codes, installation must conform with:

a. National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling

of Liquefied Petroleum Gases, ANSI/NFPA 58; or

b. Natural Gas and Propane Installation Code, CSA B149.1; Propane

Storage and Handling, CSA B149.2; or

c. The Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192; and

Recreational Vehicle Code, CSA Z240 RV Series, as applicable.

 DANGER

If you smell gas:

• Shut o gas to the appliance.

• Extinguish any open flame.

• Open hood.

• If odor continues, keep away from the appliance

and immediately call your gas supplier or your fire

department.

Failure to follow these instructions could result in fire or

property damage, personal injury or death.

MODEL: 

IMPORTANT SAFETY INFORMATION



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALACTIVATE YOUR WARRANTY

Register your appliance at

BlackstoneProducts.com/register

The North Atlantic Imports LLC 1-Year Warranty covers replacement

parts up to one year after the date of purchase.

TO ENABLE THIS WARRANTY, YOU WILL NEED TO PROVIDE:

Your appliance’s Serial Number

The Serial Number can be found on your appliance’s

Manufacturer Label.

(The Manufacturer Label is a large silver sticker found on the body of your

appliance.)

WARRANTY OVERVIEW

North Atlantic Imports, the manufacturer, will warranty for one year

from purchase all parts, workmanship, and finishes. It will be the

manufacturer’s option as to whether to repair or replace any of the

above items. All warranties are limited to the original purchaser

only. This warranty does not cover any liability on the part of North

Atlantic Imports, its agents or employees, for any indirect or conse-

quential damages for breach of warranty. The purchaser must follow

the manufacturer’s usage instructions.

Under no circumstances is the manufacturer responsible for

damages from the failure to operate the cooking station properly. It is

the responsibility of the purchaser to establish the warranty period

by verifying the original purchase date with original sales receipt.

DETAILED ExPLANATION OF THE WARRANTY

North Atlantic Imports LLC warrants to the owner that the product

covered by this agreement is free from defects in material and work-

manship under normal use and service for which it was intended if,

but only if, it has been operated in accordance with North Atlantic

Imports LLC instructions exclusively for domestic use, and not for

private or public club, institutional or commercial purposes.

North Atlantic Imports LLC’s obligation under this warranty is limited

to replacing or repairing, free of charge, any part or parts that

may prove, to the satisfaction of North Atlantic Imports LLC, to be

defective under normal home use and service within the following

stated periods of time from the date of purchase; for one year from

purchase, all parts, finish, and workmanship. Should any failure

to conform to this warranty become apparent during applicable

warranty periods stated above, the original purchaser must notify

North Atlantic Imports LLC of breach of warranty within the appli-

cable warranty period.

North Atlantic Imports LLC shall upon notice and compliance by the

original purchaser with such instructions, correct such nonconfor-

mity by repair or replacement of the defective part or parts.

Correction in the manner provided above shall constitute a fulfill-

ment of all obligations of North Atlantic Imports LLC with respect to

the quality of the product.

North Atlantic Imports LLC does not warrant this equipment to meet

the requirement of any safety code of any state, municipality or other

jurisdiction, and the original purchaser assumes all risk and liability

whatsoever resulting from the use thereof, whether used in accor-

dance with North Atlantic Imports LLC instructions or otherwise.

This warranty does not cover and is intended to exclude any liability

on the part of North Atlantic its agents, servants or employees

whether under this warranty or implied by law for any indirect or

consequential damages for breach on any warranty. The purchaser

must establish all applicable warranty periods pursuant to this

warranty by verifying the original purchase date by producing the

dated sales receipt. This warranty shall not apply to this product or

any other part thereof which has been subject to accident, negli-

gence, alteration, abuse, or misuse or which has been repaired or

altered without North Atlantic written consent, outside of North

Atlantic Imports LLC factory. The full manufacturer warranty is

not valid for griddles purchased from unlicensed, third-party

resellers, purchased at a discount due to missing or damaged

parts, or purchased as a floor model; at the discretion of North

Atlantic Imports.

North Atlantic Imports LLC makes no warranty whatsoever in respect

to accessories or parts not supplied with it. This warranty shall

apply only within the boundaries of the United States of America and

Canada. This warranty gives the original purchaser specific rights,

and the original purchaser may also have other rights, which vary

from state to state.

��

FREE

MOBILEFRIENDLY

COOKBOOK

when you register



MODEL: 

ACTIVATE YOUR WARRANTY



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE MODEL: 

ASSEMBLY GUIDE

PARTS LIST

ExPLODED VIEW

PARTS

QTY

1.1

Bottom panel



1.2

Bale panel



1.3 Gas rail 

1.4 Ignition needles 

1.5 H Burners 

PARTS

QTY

1.6

Control knob bezels



1.7

Control knobs



1.8 Hat channel 

2.1 Hood 

2.2 Hood hinges 

PARTS

QTY

2.3

Griddle top



5.1

Upper right leg

assembly



5.2 Upper left leg

assembly 

PARTS

QTY

5.3

Lower legs



5.4

Leg thumbscrews



5.5 Leg caps 

5.6 Locking pin

assembly 

4

2.1

2.2

2.3

6

8

1.8

1.2

1.3

1.4

1.5

1.6

1.7

5

7

1

5.6

5.1

5.2

5.3

5.4

5.5

1.1

3



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALASSEMBLY GUIDE

ASSEMBLY INSTRUCTIONS

Find a large, clean area to assemble your appliance.

Remove all packing material before assembling.

 CAUTION

Sharp edges. Wear gloves while assembling.

ELECTRIC REQUIREMENTS:

120V 60Hz

TOOLS NEEDED:

Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to

protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

AAA battery

TOOLS NEEDED:

Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to LPG cylinder must include collar to

protect LPG cylinder valve. protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

AAA battery

TOOLS NEEDED:

Phillips head screwdriver &

Adjustable wrench

TOOL NEEDED:

Phillips head screwdriver

TOOL NEEDED:

Adjustable wrench

TOOL NEEDED:

5mm Allen wrench

NOT INCLUDED:

LPG cylinder

Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)Size: 18 x 12 in (45 x 30 cm), 20 lb (9 kg)

LPG cylinder must include collar to LPG cylinder must include collar to

protect LPG cylinder valve. protect LPG cylinder valve.

NOT INCLUDED:

17" griddle base

NOT INCLUDED:

22" griddle base

NOT INCLUDED:

AA battery

NOT INCLUDED:

LPG cylinder

Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)Size: 4 x 8 in (10 x 20 cm), 1 lb (453 g)

NOT INCLUDED:

AAA battery

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

STEP 06

Carefully replace burners

and reattach.

 The gas rail fuel nozzle

must be reengaged within the

burner opening.

STEP 01 Ensure that the gas is turned OFF at control knobs and gas

supply. Remove the cooking top.

CLEANING THE BURNER ASSEMBLY

STEP 02 Carefully detach and

remove the burner.

STEP 03 Clean the inside of

the burner:

• Run a narrow bottle brush

through each burner tube

several times. (DO NOT use

wire brushes)

• Run a sti wire bent into a small

hook through each burner tube

several times.

• Use compressed air to blow

through the burner tube and

out the burner ports. Check that

air blows through each hole.

(Wear eye protection)

STEP 04 Brush entire

outer surface of burner to

remove grime.

STEP 05 Clean any blocked ports

with sti wire such as an open

paper clip.

VIDEO TUTORIAL

How to Clean Your Burner Tube

 youtube.com/watch?v=xKQTCrFCzf8

CUSTOMER SERVICE

Visit us online at blackstoneproducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SERVICE HOURS:

 Monday – Friday

7:00 am – 5:00 pm (MST)

Fuel nozzle

Burner opening

MODEL: 

1 Griddle body (1 piece) 2 Griddle top and

hood (1 piece)

3 Side shelf

(1 piece)

4 Hood handle

(1 piece)

5 Griddle stand

(1 piece)

6 Griddle feet

(1 piece)

7 Grease cup

(1 piece)

8 Propane regu-

lator (1 piece)

9 Bulk tank

adapter hose (1 piece)

10 M6 screws

(2 pieces)

11 M8 flange nuts

(4 pieces)

STEP 01 Place griddle on its back. Use four (4) M8 flange nuts to

attach the four (4) griddle feet to the bottom of the griddle.

Ensure that the fuel nozzle is housed within the burner opening.



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | ASSEMBLY GUIDE

Make sure the front pins are fully

seated in the holes, then push

the griddle top back to lock the

griddle in place.

Place the two front pins into the

front locking holes and push the

griddle top and hood back. Then,

set the two rear pins into the

rear holes.

Place the two front pins into the

front locking holes and push the

griddle top and hood back. Then,

set the two rear pins into the

rear holes.

Make sure the front pins are fully

seated in the holes, then push

the griddle top back to lock the

griddle in place.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

Make sure the front pins are fully

seated in the holes, then push

the griddle top forward to lock

the griddle in place.

MODEL: 

STEP 02 Remove the griddle stand from the packaging and open the

stand legs. Once the legs are fully open, the locking pins will engage.

(To close the legs, pull on the locking pins to disengage them.)

STEP 03 Adjust the legs to desired height and turn the thumbscrews

to tighten.

STEP 04 Attach the side shelf by sliding the tear-shaped holes over

the pre-inserted screws on the right side of the griddle stand. Push

the shelf down to lock it into place.

STEP 05 Place the griddle on the stand. The four (4) feet on the

bottom of the griddle will line up with the corresponding holes for

secure placement.

STEP 06 Hang the grease cup in the slot on the back of the

griddle body.

Place the griddle top onto the griddle body by aligning the four pins

to the holes of the body.

Locking pin



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

REGULATOR SAFETY

 WARNING

Cross threading can occur if you force thread a connection

at an improper angle. This will damage the threads, lead to

propane leaking, and potentially result in a build-up of fuel

that can ignite.

DO NOT cross thread the connection between your LPG

cylinder and regulator or regulator and gas rail.

 WARNING

If you can not connect the regulator, DO NOT use the

regulator.

Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

Use this appliance, as purchased, only with gas and regulator/valve

assembly supplied.

If regulator fails in unit, it must be replaced with a Blackstone approved model

(found on your Manufacturer label) by a professionally licensed, authorized

dealer. Failure to comply will void the warranty.

CONNECT THE LPG CYLINDER

1 LB (453 G)

STEP 01 Screw in the LPG cylinder into the gas regulator, turning the

cylinder clockwise.

The regulator may make a humming or whistling noise during operation. This

will not aect safety or use of the appliance.

 CAUTION

NEVER leave oil exposed in the rain. This can lead to severe

burns.

Place the included hardcover on the burner when not in use

or if it begins to rain.

NOTICE

• Maximum weight on the side shelf is 10 lbs (4.5 kg).

• The side shelf may get hot while appliance is in use.

 CAUTION

Grease build-up on the Flame Tamper can catch fire when

heated.

To prevent damage to the unit and/or injury, clean the top of

the Flame Tamper after each use.

NOTICE

DO NOT sit or stand on the table.

NOTICE

• Maximum weight on the tabletop is 100 lbs (45 kg).

• Maximum weight on the inner shelf is 50 lbs (22.5 kg).

• Maximum weight on the side shelf is 10 lbs (4.5 kg).

 CAUTION

Handle will get hot while appliance is in use.

DO NOT touch the handle while appliance is hot.

 CAUTION

Heavy pieces. Two people should assemble this appliance.

NOTICE

Place appliance on a heat-resistant and flame-resistant

surface while in use.

NOTICE

DO NOT leave the hood closed for more than 10 minutes while

cooking.

NOTICE

• DO NOT mix old and new batteries.

• DO NOT mix alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc.) batteries.

MODEL: 

USING YOUR BLACKSTONE

STEP 07 Use two (2) M6 screws to attach the handle to the hood. STEP 08 Proceed to USING YOUR BLACKSTONE.



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

STEP 02 Insert the regulator and LPG cylinder into the gas line of the

appliance. Turn the collar of the regulator clockwise to secure it to

the gas line.

LPG CYLINDER SAFETY

• The LPG supply cylinder to be used must be constructed and

marked in accordance with the specifications for LP gas cylin-

ders, U.S. Department of Transportation (DOT) or the Standard for

Cylinders, Spheres and Tubes for the Transportation of Dangerous

Goods, CAN/CSA-B339.

• Only LPG cylinders marked “propane” shall be used.

• The cylinder used, if in excess of 2.2 Ib (1.00 kg) propane capacity,

must include a collar to protect the cylinder valve.

• The LPG cylinder supply system must be arranged for vapor

withdrawal.

Always keep new LPG cylinders in upright position during use, transit or

storage.

Ensure that the LPG cylinder is positioned below the regulator.

(If the liquid level of the propane is above the regulator, the regulator will frost.)

IF FROSTING PERSISTS AFTER BOTTLE IS ANGLED CORRECTLY:

STEP 01 Turn o the appliance and disconnect LPG cylinder

immediately.

This indicates a problem with the LPG cylinder and it should not be used on any

product.

STEP 02 Return LPG cylinder to supplier.

LEAK TEST INSTRUCTIONS

NOTICE

DO NOT use household cleaning agents. Damage to gas valve

and regulator components may result.

Use a clean paintbrush and a 10/90 mild soap and water

solution to perform the leak test.

STEP 01 Turn the control knobs to OFF.

STEP 02 Connect the LPG cylinder to the regulator. Connect the

regulator to the appliance.

The regulator may make a humming or whistling noise during operation. This The regulator may make a humming or whistling noise during operation. This

will not aect safety or use of the appliance.will not aect safety or use of the appliance.

STEP 03 Brush soapy solution

onto joint areas of valves and

regulator.

Leaks are indicated by growing Leaks are indicated by growing

bubbles.bubbles.

STEP 04 If growing bubbles

appear, re-tighten connections.

 WARNING

If leaks cannot be stopped,

DO NOT try to repair.

Regulator must be replaced

with a Blackstone approved

model.

The gas regulator is intended to be

used at an angle towards the rear of

the appliance.

ADAPTER HOSE INSTRUCTIONS

The Blackstone Adapter Hose is used to connect a 20 lb (9 kg) LPG

cylinder to an appliance that uses a 1 lb (453 g) LPG cylinder.

The 20 lb (9 kg) LPG cylinder must be closed before connecting the adapter

hose.

STEP 02 Connect the adapter

hose to the 20 lb (9 kg) LPG

cylinder (not included).

STEP 01 Connect the adapter

hose to the gas rail.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

CONNECT THE LPG CYLINDER

20 LB (9 KG)

STEP 01 Turn the control

knobs to OFF.

Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

Remove the safety cap from

the Type 1 valve outlet.

STEP 02 Hold the regulator in a

straight line with the Type 1 valve

outlet so as not to cross thread

the connection.

Center and insert the regu-

lator nipple into the Type 1

valve outlet.

Hand-tighten the coupling nut in

a clockwise direction.

(DO NOT use tools to connect.)

If connection cannot be completed,

disconnect regulator and repeat this

step.

THE LPG CYLINDER VALVE MUST HAVE:

• Type 1 valve outlet (thread on the outside).

• Safety relief valve.

• UL listed Overfill Protection Device (OPD). This OPD safety feature is

identified by a unique triangular hand wheel.

• Safety cap (dust cap).

LPG CYLINDER REQUIREMENTS

• The LPG supply cylinder to be used must be constructed and

marked in accordance with the specifications for LP gas cylin-

ders, U.S. Department of Transportation (DOT) or the Standard for

Cylinders, Spheres and Tubes for the Transportation of Dangerous

Goods, CAN/CSA-B339.

• Only LPG cylinders marked “propane” shall be used.

The LPG cylinder supply system must be arranged for vapor

withdrawal.

•

Always keep new LPG cylinders in upright position during use, transit or

storage.

•

Always keep the ventilation opening(s) of the cylinder enclosure free and

clear from debris.

REGULATOR SAFETY

 WARNING

Cross threading can occur if you force thread a connection

at an improper angle. This will damage the threads, lead to

propane leaking, and potentially result in a build-up of fuel

that can ignite.

DO NOT cross thread the connection between your LPG

cylinder and regulator.

 WARNING

If you can not connect the regulator, DO NOT use the

regulator.

Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

Use this appliance, as purchased, only with gas and regulator/valve

assembly supplied.

FITTINGS & HOSES

• Annual checking and tightening of metal fittings is recommended.

• Keep the fuel supply hose away from any heated surfaces.

• Before each use, check to see if hoses are cut or worn.

Replace damaged hose before using appliance. (Use only Blackstone approved

replacement parts for valve, hose, or regulator. Failure to comply will void the

warranty.)

LPG cylinder valveLPG cylinder valve

Safety relief

valve

OPD hand wheel

Type 1 valve

outlet

Safety cap

Coupling nutCoupling nut

Regulator nippleRegulator nipple

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

LEAK TEST INSTRUCTIONS

NOTICE

DO NOT use household cleaning agents. Damage to gas valve,

hose, and regulator components may result.

Use a clean paintbrush and a 10/90 mild soap and water

solution to perform the leak test.

LEAK TEST: LPG CYLINDER

• Leak test new and exchanged LPG cylinders BEFORE connecting

to griddle.

• DO NOT smoke during leak test.

• DO NOT use an open flame to check for gas leaks.

• Appliance must be leak tested outdoors in a well-ventilated

area, away from ignition sources such as gas fired or electrical

appliances.

• During leak test, keep appliance away from open flames or sparks.

LEAK TEST: VALVES, HOSE & REGULATOR

STEP 01 Turn the control knobs to OFF.

STEP 02 Connect the regulator to the LPG cylinder.

STEP 03 Completely open the LPG tank by turning the OPD hand

wheel counterclockwise.

• If you hear a rushing sound, turn gas o immediately. There is a

major leak at the connection.

• Immediately close the LPG cylinder by turning the OPD hand wheel

clockwise and re-tighten connections. If leaks cannot be stopped

DO NOT TRY TO REPAIR.

STEP 01 Brush soapy solution

onto joint areas of the LPG

cylinder.

(Indicated by arrows in figure 01.)

• Leaks are indicated by

growing bubbles.

 WARNING

If growing bubbles appear

during leak test, DO NOT use

or move the LPG cylinder.

Immediately contact an LPG

supplier or fire department.

STEP 04 Brush soapy solution

onto joint areas of valves and

regulator.

(Indicated by arrows in figure 02.)

• Leaks are indicated by

growing bubbles.

• Immediately close the LPG

cylinder by turning the OPD

hand wheel clockwise and

re-tighten connections.

 WARNING

If leaks cannot be stopped, DO NOT try to repair.

Regulator must be replaced with a Blackstone approved

model by a professionally licensed, authorized dealer.

figure 02

figure 01

FIRST TIME CLEANING

CLEANING YOUR GRIDDLE TOP

NOTICE

Soap will ruin a seasoned griddle. This is the only time you

should use soap on the griddle cooking surface.

STEP 01 Wash the griddle cooking surface with hot, soapy water.

STEP 02 Rinse and dry completely.

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

• DO NOT use soap on the griddle top. This will destroy the griddle’s

seasoning.

• The grease cup must be removed and emptied after each use.

 CAUTION

Grease cup will be hot during and after use. DO NOT remove

the grease cup until the griddle has completely cooled.

STEP 01 Push loose food debris

into the grease cup with spatula

or straight metal scraper.

STEP 02 Wipe down griddle top

with paper towel.

STEP 03 Apply a few tablespoons

of water to the griddle surface,

then scrape the water and debris

into the grease cup.

(For stuck-on food residue, use a

bit of coarse salt.)

STEP 04 Wipe again with a paper

towel and dry completely.

STEP 05 Apply thin coat

of cooking oil to maintain

seasoning and protect the

griddle top.

VIDEO TUTORIAL

How to Clean your Blackstone Griddle

 youtube.com/watch?v=-Iedu9z6NPY

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

Push the control knob in to

start gas flowing.

Turn the control knob

counter-clockwise to activate

the starter.

Adjust the temperature to

desired level.

2. PIEZO-ELECTRIC GRIDDLE IGNITION

 DO NOT lean over the appliance while lighting.

IGNITION INSTRUCTIONS

1. CHECK VALVES

STEP 01 Turn knob to OFF position.

STEP 02 Push in knob and release. Knob should spring back.

If knobs

DO NOT

spring back, replace valve assembly before using appliance.

STEP 03 Rotate knob to LOW then turn back to OFF. Knob should

turn smoothly.

 WARNING

If burner does not ignite with open LPG cylinder valve, gas

will continue to flow out of burner and could accidentally/

inadvertently ignite with risk of injury.

Ensure gas is o at the supply shut o valve before checking

appliance valves.

HEALTHY BURNER FLAME

PATTERN

HEALTHY BURNER FLAME

PATTERN

BURNER FLAMES ARE YELLOW

OR IRREGULAR

BURNER FLAMES ARE YELLOW

OR IRREGULAR

3. CHECK BURNER FLAME

Always check burner flame

before use.

STEP 01 Light burners and rotate

knobs from HIGH to LOW.

STEP 02 Look below the cooking

top to view burners. When knob

is at HIGH, flames should be

larger than when knob is at LOW.

3. CHECK BURNER FLAME

Always check burner flame

before use.

STEP 01 Light burner and rotate

knob from LOW to HIGH.

STEP 02 Look below the turntable

to view burner. When knob is at

HIGH, flames should be larger

than when knob is at LOW.

Flickers of yellow color.

Dark blue color.

Vibrant blue.

Flickers of yellow color.

Dark blue color.

Vibrant blue.

 WARNING

A clogged burner can

lead to a fire beneath the

appliance.

Burner should be removed

and cleaned annually or

whenever heavy build-up

or insects/insect nests are

found.

 WARNING

A clogged burner can

lead to a fire beneath the

appliance.

Burner should be removed

and cleaned annually or

whenever heavy build-up

or insects/insect nests are

found.

If there is a sudden drop or low

flame issue, please reference the

Troubleshooting chapter.

If there is a sudden drop or low

flame issue, please reference the

Troubleshooting chapter.

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

WHAT OIL IS BEST TO USE?

• Blackstone Seasoning and

Cast Iron Conditioner.

• Any plant-based cooking oil.

• Rendered animal fat with no

additives.

STEP 01 Wipe any debris o

griddle top.

GRIDDLE SEASONING INSTRUCTIONS

STEP 02 Set your griddle to

high heat until your griddle top

changes color. (~10 min)

STEP 04 The griddle top is ready

for another layer of oil when it

stops smoking. Repeat STEP 03

3-4 times, or until the griddle

surface is black.

SEASONING TROUBLESHOOTING

THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:

VIDEO TUTORIAL

How to Season a New Blackstone Griddle

 youtube.com/watch?v=VspmDVnj2pI&t=3s

STEP 03 Use tongs to hold a

paper towel or cotton cloth and

spread 2-3 tablespoons of your

seasoning oil across the entire

griddle top.

When seasoning your griddle top,

remember to use a thin and even layer

of oil—the thinner the layer of oil, the

easier it will be to burn it o.

VIDEO TUTORIAL

Recovering your Blackstone Griddle Top

 youtube.com/watch?v=thPE2IgnSiI

PREVENTING RUST

Use your griddle frequently. Every time you cook, you are adding to

the seasoning, which makes rust less likely.

NOTICE

If you live in a humid or coastal climate, your griddle may

require more frequent seasonings between uses.

If rust appears on the griddle surface, rub it o with steel wool, low

grit sandpaper or the Blackstone Pumice Stone and re-season

the surface.

THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:

After using your griddle for multiple cooks, the seasoning will even

out and improve.

POSSIBLE CAUSES SOLUTION

• Too much oil was used.

• You turned o the heat too

soon.

STEP 01 Turn your griddle on high

and let it heat for 10-15 minutes.

STEP 02

Scrape o as much

of the thickened and partially

cooked oil as you can.

STEP 03

Re-season with a very

thin layer of oil.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

COOKING ON YOUR BLACKSTONE

 DANGER

Flammable items can spontaneously combust if placed near

the appliance. DO NOT place flammable items such as aerosol

containers, oily or greasy towels near the cooking surface.

 CAUTION

This appliance will be hot during and after use. DO NOT

handle hot parts with unprotected hands. Use long-handled

cooking utensils and oven mitts.

NOTICE

DO NOT store any items within 3 in (8 cm) of the cooking

surface while in use.

IF GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR

REGULATOR:

STEP 01 Turn o gas supply immediately.

STEP 02 Determine the cause and correct it.

STEP 03 Clean and inspect valve, hose and regulator.

STEP 04 Perform a leak test. (Please reference the Leak Test

Instructions in USING YOUR BLACKSTONE.)

VIDEO RECIPES

Find recipes and cooking tips at:

 BlackstoneProducts.com/blogs/recipes

 youtube.com/c/BlackstoneGriddles

   @blackstoneproducts

STRAWBERRIES AND CREAM

PANCAKES

Breakfast

TACOS BORRACHOS

Dinner

OKLAHOMA FRIED ONION

BURGER

Lunch

APPLIANCE STORAGE

 WARNING

DO NOT move the appliance when in use. Allow the appliance

to cool to 115°F (45°C) before moving or storing.

COVER FIT GUIDE

Always cover your appliance when stored outdoors.

To find a cover that will fit your appliance, visit

BlackstoneProducts.com/support.

CLEANING YOUR APPLIANCE

Clean your appliance after each use, after it is cool to the touch.

• DO NOT use abrasive pad on areas with graphics.

• If a bristle brush is used to clean any of the cooking surfaces,

ensure no loose bristles remain on cooking surfaces prior

to cooking.

 WARNING

Grease build up can cause a fire. Clean any part of the

appliance that gets hot and experiences grease build up after

each use.

PLASTIC PARTS & PAINTED SURFACES:

Wash with warm soapy water and wipe dry with a non-abra-

sive cloth.

NOTICE

DO NOT use Citrisol, abrasive cleaners, or a concentrated

cleaner on plastic parts. This may result in damage to and

failure of parts.

FOR EVERY SURFACE

The Blackstone Degreaser

and Cleaning Spray is gentle

enough to clean every surface

of your appliance. Use it on the

cooking surface, the appliance

frame, or anywhere that experi-

ences a build up of grease.

PULL OUT MOUNTING / STORAGE SYSTEMS:

 DANGER

DO NOT put appliance in storage or travel mode immediately

after use. Allow appliance to cool to touch before moving

or storing. Failure to do so could result in fire resulting in

property damage, personal injury, or death.

This model is suitable for use in an RV when installed in a manner

similar to the slide out tray as shown.

The minimum load specification for the slide out tray when fully extended and The minimum load specification for the slide out tray when fully extended and

in the locked position is 100 lbs. (45.5 Kg.) in the locked position is 100 lbs. (45.5 Kg.)

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | USING YOUR BLACKSTONE

FIRST TIME CLEANING

CLEANING YOUR GRIDDLE TOP

NOTICE

Soap will ruin a seasoned griddle. This is the only time you

should use soap on the griddle cooking surface.

STEP 01 Wash the griddle cooking surface with hot, soapy water.

STEP 02 Rinse and dry completely.

CLEANING YOUR GRIDDLE TOP

Clean griddle top after each use, while still warm.

• DO NOT use soap on the griddle top. This will destroy the griddle’s

seasoning.

• The grease cup must be removed and emptied after each use.

 CAUTION

Grease cup will be hot during and after use. DO NOT remove

the grease cup until the griddle has completely cooled.

STEP 01 Push loose food debris

into the grease cup with spatula

or straight metal scraper.

STEP 02 Wipe down griddle top

with paper towel.

STEP 03 Apply a few tablespoons

of water to the griddle surface,

then scrape the water and debris

into the grease cup.

(For stuck-on food residue, use a

bit of coarse salt.)

STEP 04 Wipe again with a paper

towel and dry completely.

STEP 05 Apply thin coat

of cooking oil to maintain

seasoning and protect the

griddle top.

VIDEO TUTORIAL

How to Clean your Blackstone Griddle

 youtube.com/watch?v=-Iedu9z6NPY

DISCONNECT THE LPG CYLINDER

1 LB (453 G)

STEP 01 Ensure that the control knob(s) are turned to OFF.

STEP 02 Once the appliance has cooled, disconnect the regulator

from the gas line by unscrewing the collar.

STEP 03 Unscrew the LPG cylinder from the regulator.

STEP 04 Place dust cap on LPG cylinder valve outlet whenever

cylinder is not in use.

Only install the type of dust cap on cylinder valve outlet that is provided

with the cylinder valve. Other types of caps or plugs may result in leakage of

propane.

STORING LPG CYLINDERS

 WARNING

• DO NOT store a spare LPG cylinder under or near this

appliance.

• DO NOT fill an LPG cylinder beyond 80% full.

If the information above is not followed exactly, a fire causing

death or serious injury may occur.

• The LPG cylinder must be disconnected when the appliance is

not in use.

• Only store the appliance indoors if the LPG cylinder is disconnected

and removed from the appliance.

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALUSING YOUR BLACKSTONE

DISCONNECT THE LPG CYLINDER

20 LB (9 KG)

STEP 01 Ensure that the control knobs are turned to OFF.

Ensure that the LPG cylinder

is OFF by turning the OPD hand

wheel clockwise to a full stop.

Turn the coupling nut count-

er-clockwise by hand to remove

the regulator. (DO NOT use tools

to disconnect.)

STEP 02 Place safety cap on LPG

cylinder valve outlet whenever

cylinder is not in use.

Only install the type of safety cap on

cylinder valve outlet that is provided

with the cylinder valve. Other types of

caps or plugs may result in leakage of

propane.

STORING LPG CYLINDERS

 WARNING

• DO NOT store a spare LPG cylinder under or near this

appliance.

• DO NOT fill an LPG cylinder beyond 80% full.

If the information above is not followed exactly, a fire causing

death or serious injury may occur.

• The LPG cylinder must be turned OFF when the appliance is

not in use.

• LPG cylinders must be stored outdoors and out of the reach

of children.

• DO NOT store an LPG cylinder inside a building, garage, or any other

enclosed area.

FILLING & ExCHANGE

• Use only those reputable exchange companies that inspect, preci-

sion fill, test and certify their cylinders. LPG dealer must purge new

cylinder before filling.

• Volume of propane in cylinder will vary by temperature.

 WARNING

A frosty regulator indicates gas overfill.

Immediately close LPG cylinder valve and call local LPG

dealer for assistance.

• DO NOT release liquid petroleum gas (LPG) into the atmosphere.

• To remove gas from LPG cylinder, contact a certified LPG dealer or

local fire department for assistance.

• Exchange cylinder only for an OPD safety feature-equipped

cylinder.

Your retailer can help you match a replacement LPG cylinder to your appliance.

Storing the Appliance goes here

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL | TROUBLESHOOTING

POSSIBLE CAUSES SOLUTION

Something is blocking the

venturi in the burner.

Clean the burner assembly to

remove the obstruction.

POSSIBLE CAUSES SOLUTION

Obstructions in the burner, gas

jets, or fuel rail.

Clean the burner, jets, and gas

hose.

LPG cylinder is empty or low.

Refill or replace the LPG

cylinder.

The regulator’s flow limiting

device was triggered.

Reset the safety system:

STEP 01

Turn OFF the appliance,

close the LPG cylinder valve, and

disconnect the regulator from

the LPG cylinder.

STEP 02

Wait five minutes to

allow the pressure to dissipate,

then reconnect the regulator

to the LPG cylinder and slowly

open the OPD hand wheel one

half turn.

STEP 03

Ignite your appliance.

Regulator stuck in safety

position. Contact customer service for

replacement parts.

GAS FLOW TROUBLESHOOTING

A FLAME IS COMING OUT OF THE AIR GATE:

BURNER FLAMES ARE YELLOW OR IRREGULAR:

• Appliance will not achieve a high heat or heats unevenly.

• Burner flames start strong, then immediately drop to low even

when burner is set to high position.

• Flame height drops when a second burner is lit.

• Flames DO NOT extend the full length of the burner, or only run on

one side of the burner.

• Burner flames are inconsistent.

IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Ignitor wire misaligned.

Ensure that the ignition needle

is positioned 3-7mm away from

the burner tube, and above a

burner hole.

Damage to the ignition system.

Contact customer service for

replacement parts.

IF YOU CAN NOT IGNITE YOUR APPLIANCE WITH A MATCH:

POSSIBLE CAUSES SOLUTION

Burner tubes are not receiving

fuel. Clean the burner assembly to

remove the obstruction.

3-7mm

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If this does not work, to determine the cause, please try to ignite your appli-

ance with a match.

IGNITION TROUBLESHOOTING

BURNER WILL NOT IGNITE:

If ignition does not occur in 5 seconds:

STEP 01 Turn the burner control knob OFF.

STEP 02 Wait 5 minutes.

STEP 03 Repeat the lighting procedure.

If this does not work, to determine the cause, please try to ignite your appli-If this does not work, to determine the cause, please try to ignite your appli-

ance with a match. ance with a match.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Open hood (if applicable).

STEP 01 Turn control knob to OFF position.

MATCH LIGHTING INSTRUCTIONS

Before beginning, check for gas leaks. Before beginning, check for gas leaks.

STEP 01 Turn control knob to OFF position.

STEP 04 Push in and turn the control knob to start gas flowing.

Ensure burner lights and stays lit.

STEP 04 Push in and turn the control knob to start gas flowing.

Ensure burner lights and stays lit.

STEP 02 Light a match (or long

lighter) no shorter than 11

inches long.

STEP 03 Place the flame next to

the burner.

STEP 02 Light a match (or long

lighter) no shorter than 11

inches long.

STEP 03 Place the flame next to

the burner.

MODEL: 

TROUBLESHOOTING



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUALTROUBLESHOOTING

STEP 06

Carefully replace burners

and reattach.

 The gas rail fuel nozzle

must be reengaged within the

burner opening.

STEP 01 Ensure that the gas is turned OFF at control knobs and gas

supply. Remove the cooking top.

CLEANING THE BURNER ASSEMBLY

STEP 02 Carefully detach and

remove the burner.

STEP 03 Clean the inside of

the burner:

• Run a narrow bottle brush

through each burner tube

several times. (DO NOT use

wire brushes)

• Run a sti wire bent into a small

hook through each burner tube

several times.

• Use compressed air to blow

through the burner tube and

out the burner ports. Check that

air blows through each hole.

(Wear eye protection)

STEP 04 Brush entire

outer surface of burner to

remove grime.

STEP 05 Clean any blocked ports

with sti wire such as an open

paper clip.

VIDEO TUTORIAL

How to Clean Your Burner Tube

 youtube.com/watch?v=xKQTCrFCzf8

CUSTOMER SERVICE

Visit us online at blackstoneproducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SERVICE HOURS:

 Monday – Friday

7:00 am – 5:00 pm (MST)

Fuel nozzle

Burner opening

CUSTOMER SERVICE

Visit us online at BlackstoneProducts.com/support

for assistance concerning appliance use, replacement parts, or

your warranty.

CUSTOMER SERVICE HOURS:

 Monday – Friday

7:00 am – 5:00 pm (MST)

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

OWNER’S MANUAL |

This page intentionally left blank

MODEL: 



BLACKSTONEPRODUCTS.COM/SUPPORT

ENGLISH

| OWNER’S MANUAL

This page intentionally left blank

MODEL: 



ENGLISH

BLACKSTONEPRODUCTS.COM/SUPPORT

This product may be covered by one or more issued U.S. and/or

international patents and may include patent applications pending.

For more information, please visit: BlackstoneProducts.com/patents

DISTRIBUTED BY NORTH ATLANTIC IMPORTS, LLC  W  N LOGAN, UT  USA | BLACKSTONE IS A REGISTERED TRADEMARK OF NORTH ATLANTIC IMPORTS, LLC



La page charge ...

Blackstone 1891 22 Inch Griddle Le manuel du propriétaire

Blackstone 1891 22 Inch Griddle Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents