TECHNICAL FILE
R03.001_19/06/2014
Novorodapie® Stainless steel is a skirting prole made of AISI304
stainless steel. With smoothed visible side, is very easy to install
with common adhesives. It is delivered with protective lm to
avoid possible stains or damage during the handling or transport.
Available in high brightness and brushed nishes and with all the
complementary pieces needed.
Novorodapie® Stainless
Steel
Material: Stainless steel
Lenght: 2 lm
Dimensions: a: 60 mm
Packaging: 10 u/box
With protective lm
Finishes: High brightness/brushed
Applications
Novorodapie® Stainless Steel is a skirting prole made of AISI304 stainless steel. This skirtingboard has
been designed to protect the bottom of the walls and decorate them at the same time. It has a great
decorative value. Very easy to install.
This prole is available with an acoustic insulating which helps to fulll the CTE-DB-HR (Document for
the protection against the noise) by reducing the sound level.
Complementary pieces
Covers
Exterior angle
Interior angle
Novorodapie® Stainless steel has complementary pieces available to get a perfect nish.
Technical Features
General Features
Page 1 of 3
Alloy
AISI-304
Composition test of each batch
AIMME
Corrosion resistance
Salt spray test
+ 504 hours without change (stainless
steel)
UNE 112017:92
AIMME
TECHNICAL FILE
R03.001_19/06/2014
Novorodapie® Stainless steel
1. Clean the inner side of Novorodapie® Stainless steel and the surface where is to be placed.
2. Join the complementary pieces to Novorodapie® Stainless steel. This previous step will help to install
the whole set to the wall. To keep the pieces in its position, you can use an adhesive tape as help. Be
careful and remove partially the protective lm on the areas in direct contact with the wall.
3. Thirdly, put a big amount of adhesive on the inner side of Novorodapie® Stainless steel in the areas
in contact with the wall. You can use an adhesive like silicone or polyurethane mastic.
4. Place the Novorodapie® Stainless steel on the wall and press softly to get a perfect adhesion. Be
sure the complementary pieces remain on their correct position.
5. Finally, clean the leftover material an let dry. After drying, remove the protective lm.
*If you are going to paint the wall, keep the protective lm until you have nished.
Installation
Page 2 of 3
Cleaning and maintenance
Materials
Stainless
steel
Novoescocia® Plus Stainless Steel is a prole made of stainless steel AISI-304. All material batches are
tested with the composition test to determine that they fulll with the specication of the alloy. Stain-
less steel used in the Emac® products has been also tested with salt spray test, exceeding 500 hours
of exposition without signs of corrosion.
Stainless steel is a highly durable and resistent material, with an excellent supercial appearance that
does not degrade along the time. Available in brushed nish. This nish is slightly porous and smooth,
making easier the hygiene of the installation.
The complementary pieces are made of folded stainless steel sheet.
The immediate cleaning of the material after its installation is necessary to avoid that remainings of
mortar, concrete or iron particles from wool or tools could cause corrosion.
For indoor applications, you can use water with detergent or liquid soap to remove dirtiness and pos-
sible ngerprints marked on the surface. In high brightness nishes, you can use a glass cleaner. There
are specic cleaners in the markets for stainless steel which clean the material and reduce possible
stains. Whenever you clean stainless steel, ensure you rinse it well and dry totally to prevent fogging.
Steel wool or similar products, are not recommended because they could scratch the surface and
create pitting corrosion. Pay special attention while using materials containing chlorides, they are not
indicated because could oxidize the material. Hydrochloric acid or iron products in a long contact with
the material are neither recommended. Do not use cleaners for common steel for the cleaning of
stainless steel.
TECHNICAL FILE
R03.001_19/06/2014
Technical information
You can nd out more information about the technical features of Emac®’s products by downloading
their Technical File from www.emac.es
If you have any query please contact our Technical Department in [email protected]
Emac Complementos S.L. (Spain) info@emac.es // Emac America L.L.C. (FL,USA) [email protected] // Emac Italia S.R.L. (Italy) [email protected]
www.emac.es
The data provided are for information only and have been obtained by our supplier or Emac®.
Does not constitute legal guarantee in terms of properties and / or functionality of the application of material
Novorodapie® Stainless steel
Indoors Wall tiling
Page 3 of 3
Outdoors
-
1
-
2
-
3
dans d''autres langues
- English: Emac NRE88656 Installation guide
Documents connexes
-
Emac NS116X Guide d'installation
-
-
Unbranded SMR92 Mode d'emploi
-
-
-
-
-
-
-