Samsung HW-S61T Manuel utilisateur

HW-S60T / S61T

FULL MANUAL

Imagine the possibilities

Thank you for purchasing this Samsung product.

To receive more complete service, please register

your product at www.samsung.com/register

ENG - 2

SAFETY INFORMATION

SAFETY WARNINGS

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE THE COVER (OR BACK).

NO USER-SERVICEABLE PARTS ARE INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

Refer to the table below for an explanation of

symbols which may be on your Samsung product.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that high voltage

is present inside. It is dangerous to

make any kind of contact with any

internal part of this product.

This symbol indicates that this product

has included important literature

concerning operation and maintenance.

Class II product : This symbol indicates

that it does not require a safety

connection to electrical earth (ground).

If this symbol is not present on a

product with a power cord, the product

MUST have a reliable connection to

protective earth (ground).

AC voltage : This symbol indicates that

the rated voltage marked with the

symbol is AC voltage.

DC voltage : This symbol indicates that

the rated voltage marked with the

symbol is DC voltage.

Caution, Consult instructions for use :

This symbol instructs the user to

consult the user manual for further

safety related information.

WARNING

• To reduce the risk of re or electric shock, do

not expose this appliance to rain or moisture.

CAUTION

• TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

• This apparatus shall always be connected to a

AC outlet with a protective grounding

connection.

• To disconnect the apparatus from the mains,

the plug must be pulled out from the mains

socket, therefore the mains plug shall be

readily operable.

• Do not expose this apparatus to dripping or

splashing. Do not put objects lled with

liquids, such as vases on the apparatus.

• To turn this apparatus off completely, you

must pull the power plug out of the wall

socket. Consequently, the power plug must

be easily and readily accessible at all times.

ENG - 3

PRECAUTIONS

1. Ensure that the AC power supply in your

house complies with the power

requirements listed on the identication

sticker located on the bottom of your

product. Install your product horizontally, on

a suitable base (furniture), with enough

space around it for ventilation (7~10 cm).

Make sure the ventilation slots are not

covered. Do not place the unit on ampliers

or other equipment which may become hot.

This unit is designed for continuous use. To

fully turn off the unit, disconnect the AC plug

from the wall outlet. Unplug the unit if you

intend to leave it unused for a long period of

time.

2. During thunderstorms, disconnect the AC

plug from the wall outlet. Voltage peaks due

to lightning could damage the unit.

3. Do not expose the unit to direct sunlight or

other heat sources. This could lead to

overheating and cause the unit to

malfunction.

4. Protect the product from moisture (i.e.

vases), and excess heat (e.g. a replace) or

equipment creating strong magnetic or

electric elds. Unplug the power cable from

the AC wall socket if the unit malfunctions.

Your product is not intended for industrial

use. It is for personal use only. Condensation

may occur if your product has been stored in

cold temperatures. If transporting the unit

during the winter, wait approximately

2 hours until the unit has reached room

temperature before using.

5. The battery used with this product contains

chemicals that are harmful to the

environment. Do not dispose of the battery

in the general household trash. Do not

expose the battery to excess heat, direct

sunlight, or re. Do not short circuit,

disassemble, or overheat the battery.

Danger of explosion if the battery is replaced

incorrectly. Replace only with the same or

equivalent type.

ENG - 4

Fabric cleaning

Remove any dirt or stain on the product surface

immediately.

Removing and cleaning can be less effective for

some substances or if left for a prolonged time.

CAUTION

• Use a vacuum cleaner or an adhesive lint

roller to remove dust, handprints, and the

likes.

– Some cleaning brushes may damage the

product, depending on the materials they

contain.

– Towels and cleaning clothes may leave

lint or dirt on the product.

• Do not use a nail or other tools to scratch the

dirt off. It may damage the fabric.

• To remove oil or liquid stains, use a clean

white cloth moist with water. If the stain

persists, wipe it with a mixture of water and

neutral detergent (such as dishwashing

soaps) and a cloth.

– A non-neutral detergent or cleaner may

cause discolouration or fabric damage.

– After cleaning, use a dry cloth or

hairdryer to dry the area.

– Do not use excessive force to avoid

discolouration or fabric damage.

ENG - 5

CONTENTS

01 Checking the Components 7

Inserting Batteries before using the Remote Control (AA batteries X 2) ------------------------- 7

02 Product Overview 8

Top Panel of the Soundbar ------------------------- 8

Bottom Panel of the Soundbar ------------------------- 10

03 Using the Remote Control 11

How to Use the Remote Control

-------------------------

11

Output specications for the different sound effect modes

-------------------------

14

Adjusting the Soundbar volume with a TV remote control ------------------------- 15

04 Connecting the Soundbar 16

Connecting Electrical Power

-------------------------

16

Connecting an SWA-8500S (Sold Separately) to your Soundbar

-------------------------

17

Connecting an SWA-W500 (Sold Separately) to your Soundbar

-------------------------

19

05 Using a wired connection to the TV 21

Method 1. Connecting with HDMI

-------------------------

21

Method 2. Connecting using an Optical Cable

-------------------------

23

06 Using a wireless connection to the TV 24

Connecting via Bluetooth

-------------------------

24

07 Connecting an External Device 26

Connecting using an Optical Cable

-------------------------

26

ENG - 6

08 Connecting a Mobile Device 27

Method 1. Connecting via Bluetooth

-------------------------

27

Method 2. Connecting via Wi-Fi (Wireless Network)

-------------------------

30

Conguring Amazon Alexa

-------------------------

31

Using the Tap Sound

-------------------------

34

09 Installing the Wall Mount 35

Installation Precautions

-------------------------

35

Wallmount Components

-------------------------

35

10 Installing the Soundbar in front of TV 37

11 Software Update 38

Auto Update

-------------------------

38

USB Update

-------------------------

38

Initialisation

-------------------------

39

12 Troubleshooting 40

13 Licence 42

14 Open Source Licence Notice 42

15 Important Notes About Service 42

16 SpecicationsandGuide 43

Specications

-------------------------

43

ENG - 7

01 CHECKING THE COMPONENTS

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Soundbar Main Unit Soundbar Remote Control

/

Batteries

HDMI Cable

AC/DC Adapter

(Soundbar)

Power Cord

(Soundbar)

Wall Mount Guide

x 2

(M4 x L10)

x 2

Holder-Screw Bracket-Wall Mount Screw

• For more information about the power supply and power consumption, refer to the label attached

to the product. (Label: Bottom of the Soundbar Main Unit)

• To purchase additional components or optional cables, contact a Samsung Service Centre or

Samsung Customer Care.

• For more information about the wallmount see page 35.

• Design, specications, and App screen are subject to change without prior notice.

• The appearance of the accessories may differ slightly from the illustrations above.

Inserting Batteries before using the Remote Control (AA batteries X 2)

Slide the back cover in the direction of the arrow

until it is completely removed. Insert 2 AA batteries

(1.5V) oriented so that their polarity is correct. Slide

the back cover back into position.

ENG - 8

02 PRODUCT OVERVIEW

Top Panel of the Soundbar

Top Panel

Position the product so that

the SAMSUNG logo is

located on the top.

󰟴 󰟶󰟵

󰟳

LED

indicator

The LED Indicator ashes, glows, or changes colour depending on the Soundbar's current

mode or status. The colour of the LED indicator and the number of lights indicate the active

mode as described below.

W

White LED

W

White LED

M

Multicolour LED

W

White LED

W

White LED

• The Multicolour LED changes to White, Cyan, Green, Red, and Blue depending on the

mode or status.

󰟴

Multi

Function

Button

• In standby mode, press the (Multi Function) button to turn on the Soundbar.

• Press the (Multi Function) button to change the mode. Each time you change the

mode, the LED lights in white and then turns off.

LED

Indicator

White On -> Off White On -> Off White On -> Off

“Digital Audio In” or

“TV ARC”

“Wi-Fi” “Bluetooth”

• Press the (Multi Function) button for 3 seconds to call Alexa. Say with the button

pressed to enable voice recognition.

󰟵

Volume

Button

Press the (Volume) button to adjust the volume.

ENG - 9

󰟶

Mic

On/Off

Button

Press the (Mic On/Off) button to turn on or off the microphone.

LED Indicator

Red On

“Mic Off” “Mic On”

• When you plug in the AC cord, the power button will begin working in 4 to 6 seconds.

• When you turn on this unit, there will be a 4 to 5 second delay before it produces sound.

• If you hear sounds from both the TV and Soundbar, go to the Settings menu for the TV audio and

change the TV speaker to External Speaker.

ENG - 10

Bottom Panel of the Soundbar

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

󰟳 󰟴 󰟵 󰟶 󰟷 󰟸

󰟳

ID SET

Press to connect the Soundbar to Surround speakers and a subwoofer wirelessly.

(The surround speaker, subwoofer are sold separately.)

󰟴

NETWORK

Press to connect to a wireless network (Wi-Fi) via the SmartThings app.

󰟵

SERVICE

Connect a USB storage device to upgrade the product's software.

󰟶

DC 19V (Power Supply In)

Connect the AC/DC power adapter. (See page 16)

󰟷

DIGITAL AUDIO IN (OPTICAL)

Connect to the digital (optical) output of an external device. (See page 26)

󰟸

HDMI (ARC)

Connect to the HDMI jack on a TV. (See page 21)

• When disconnecting the power cable of the AC/DC power adaptor from a wall outlet, pull the plug.

Do not pull the cable.

• Do not connect this unit or other components to an AC outlet until all connections between

components are complete.

ENG - 11

03 USING THE REMOTE CONTROL

How to Use the Remote Control

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

󰟳

󰟴

󰟵

󰟶

󰟷

󰟹

󰟸

󰟺

󰟼

󰟻

󰟳

Power

Turns the Soundbar on and off.

LED

Indicator

Cyan Blinks X1

On

Off

Red Blinks X3

• Auto Power Down Function

The unit turns off automatically in the following

situations:

– In “Digital Audio In” or “TV ARC” / “Wi-Fi” /

“Bluetooth” mode if there is no audio signal for

18 minutes.

󰟴

(Source)

Press to select a source connected to the Soundbar.

󰟵

(Mute)

Press the (Mute) button to mute the sound.

Press it again to unmute the sound.

LED

Indicator

Blinks X Repeatly

ENG - 12

󰟶

SOUND MODE

By pressing the button, you can select the desired audio mode. Each time the mode changes, the

Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Standard”  “Music”  “Adaptive Sound”

• Standard

Outputs the original sound.

• Music

Provides more natural and room lling sound for music content.

• Adaptive Sound

Analyzes the content in real time and automatically provides the optimal sound eld based on the

characteristics of the content.

󰟷

Bluetooth PAIR

Switch the Soundbar to Bluetooth pairing mode.

When you press the button, the LED display changes as shown below.

• Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

LED

Indicator

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

“Ready to connect via Bluetooth.”

󰟸

p (Play / Pause)

You can also play or pause music by pressing the button.

󰟹

Up/Down/Left/Right

Press Up/Down/Left/Right on the button to select or set functions.

• Music Skip

Press the Right button to select the next music le. Press the Left button to select the previous

music le.

ENG - 13

󰟺

(Sound Control)

By pressing the button, you can select the desired audio mode. The desired item can be adjusted using

the Up/Down buttons. Each time the mode changes, the Multicolour LED blinks in white.

LED

Indicator

White Blinks X1

“Treble”  “Bass”  “Sync”  “Side Level”

– To control the volume of the treble or bass sound, select “Treble” or “Bass” in Sound Settings, and

then adjust the volume between -6~+6 by using the Up/Down buttons.

– Press and hold the (Sound Control) button for about 5 seconds to adjust the sound for each

frequency band. 150Hz, 300Hz, 600Hz, 1.2kHz, 2.5kHz, 5kHz, and 10kHz are selectable using the

Left/Right buttons and each can be adjusted to a setting between -6 to +6 using the Up/Down

buttons. (Make sure the Sound mode is set to “Standard”.)

– To control the volume of the each speaker select “Side Level” in Sound Settings, and then adjust the

volume between -6~+6 by using the Up/Down buttons.

– If the video on the TV and audio from the Soundbar are not synchronised, select “Sync” in Sound

Control, and then set the audio delay between 0~300 milliseconds by using the Up/Down buttons.

– “Sync” is only supported for some functions.

󰟻

WOOFER (BASS) LEVEL

Push the button up or down to adjust the level of the woofer (bass) to -12 or between -6 to +6. To set the

woofer (bass) volume level to 0 (Default), press the button.

󰟼

VOLUME

Push the button up or down to adjust the volume.

LED

Indicator

White moves to right X1

Volume Up

White moves to left X1

Volume Down

ENG - 14

Outputspecicationsforthedifferentsoundeffectmodes

Effect Input

Output

With Subwoofer Only

With Subwoofer & Wireless

Rear Speaker Kit

Standard

2.0 ch 2.1 ch 2.1 ch

5.1 ch 2.1 ch 4.1 ch

Music

2.0 ch 4.1 ch 6.1 ch

5.1 ch 4.1 ch 6.1 ch

Adaptive Sound

2.0 ch 4.1 ch 6.1 ch

5.1 ch 4.1 ch 6.1 ch

• The Samsung Wireless Rear Speaker Kit, and Subwoofer can be purchased separately.

To purchase a Kit or the Subwoofer, contact the vendor you purchased the Soundbar from.

ENG - 15

Adjusting the Soundbar volume with a TV remote control

Adjust the Soundbar volume using the TV’s remote control.

• This function can be used with IR remote controls only. Bluetooth remote controls (remote

controls that require pairing) are not supported.

• Set the TV speaker to External Speaker to use this function.

• Manufacturers supporting this function:

VIZIO, LG, Sony, Sharp, PHILIPS, PANASONIC, TOSHIBA, Hisense, RCA

1. Turn Off the Soundbar.

2. Push up and hold the WOOFER button for 5 seconds.

Each time you push the WOOFER button up and hold it for 5 seconds, the mode switches in the

following order: “Samsung-TV Remote” (Default mode), “Off-TV Remote”, “All-TV Remote”.

The LED indicator status changes each time the mode is changed, as shown below.

Remote Control Button LED Indicator Status

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"Samsung-TV Remote"

(Default mode)

Cyan Blinks X1

Enable a Samsung TV’s IR remote

control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"Off-TV Remote"

Red Blinks X1

Disable the TV remote control.

SOUND

MODE

VOL

WOOFER

SOUNDBAR

5 Sec

"All-TV Remote"

Blue Blinks X1

Enable a third-party TV’s IR remote

control.

ENG - 16

04 CONNECTING THE SOUNDBAR

Connecting Electrical Power

Use the power components to connect the Soundbar to an electrical outlet in the following order:

• For more information about the required electrical power and power consumption, refer to the

label attached to the product. (Label: Bottom of the Soundbar Main Unit)

1. First connect the power cable to the AC/DC adapter.

Connect the AC/DC adapter (with the power cable) to the Soundbar.

2. Connect the power cord to a wall socket.

DC 19V

Power Cord

AC/DC Adapter

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

SERVICE DC 19V

HDMI

(ARC)

DIGITAL AUDIO IN

(OPTICAL)

SERVICE DC 19V

HDMI OUT

(TV-ARC)

DIGITAL AUDIO IN

(OPTICAL)

DIGITAL AUDIO IN

(OPTICAL)

ID SET NETWORK

DC 19V

Bottom of the Soundbar Main Unit

NOTES

• If you unplug and reconnect the power cord when the product is turned on, the Soundbar turns on

automatically.

• Make sure to rest the AC/DC Adapter at on a table or the oor. If you place the AC/DC Adapter so

that it is hanging with the AC cord input facing upwards, water or other foreign substances could

enter the Adapter and cause the Adapter to malfunction.

ENG - 17

Connecting an SWA-8500S (Sold Separately) to your Soundbar

Expand to true wireless surround sound by connecting the Samsung Wireless Rear Speaker Kit

(SWA-8500S, sold separately) to your Soundbar.

1. Connect the Wireless Receiver Module to 2 Surround Speakers.

– The speaker cables are colour coded.

SURROUND-LEFT

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

SURROUND-RIGHT

SURROUND-LEFT SURROUND-RIGHT

2. Check the standby status of the Wireless Receiver Module after plugging it into an electrical outlet.

• The LINK LED indicator (blue) on the Wireless Receiver Module should be blinking. If the

indicator does not blink, use a narrow pin to press and hold the ID SET button for 5 seconds or

longer. See the SWA-8500S user guide for more details.

ID SET

L

R

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

POWER

ID SET

SURROUND SPEAKERS OUT

SPEAKER IMPEDANCE : 3Ω

STANDBY

LINK

STANDBY

LINK

Blue blinking

5 Sec

ENG - 18

3. Press the Up button on the remote control for 5 seconds.

• Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

Rear Speaker, Woofer Pairing button LED Indicator

SOUND

MODE

PAIR

5 Sec

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

CAUTION

• If your Soundbar was playing music when it connects to the SWA-8500S, you may hear some

stuttering from the woofer as the connection nalises.

4. Check if the LINK LED is solid blue (connection complete).

STANDBY

LINK

STANDBY

LINK

Blue is On

The LINK LED indicator stops blinking and

glows a solid blue when a connection is

established between the Soundbar and the

Wireless Receiver Module.

5. If the SWA-8500S is not connected, repeat the procedure from Step 2.

ENG - 19

Connecting an SWA-W500 (Sold Separately) to your Soundbar

1. Turn off the Soundbar by pressing the (Power) button on the remote control.

VOL WOOFER

SOUNDBAR

SOUND

MODE

PAIR

Red Blinks X3

2. Plug in the Wireless Subwoofer, and then check its standby status.

• Plug the Wireless Subwoofer power cord into an electrical outlet and into the Wireless

Subwoofer to turn on the Wireless Subwoofer. The LINK LED indicator (blue LED) on the

Wireless Subwoofer blinks. If the LED does not blink, press the ID SET button on the rear of the

Wireless Subwoofer with a pen tip for 5~6 seconds until the LINK LED indicator blinks (in Blue).

For more about the LED, please refer to the SWA-W500 user manual.

Rear of the Wireless Subwoofer

POWER ID SET

Front of the Wireless Subwoofer

POWER ID SET

Blue blinking

POWER ID SET

ID SET

5 Sec

• The main unit is heavy. Be careful not to pinch your ngers when pressing the ID SET button or

connecting the power cord to the rear of the unit.

• The upper part of the subwoofer is prone to scratches. Handle it carefully.

Speaker Unit

Bottom of the Wireless Subwoofer

• Do not press on or strike the

Speaker Unit on the bottom of

the body. You can deform or

damage the speaker.

ENG - 20

3. Press the Up button on the remote control for 5 seconds.

• Until pairing is complete, the Multicolour LED changes as Red → Green → Blue in turn.

Rear Speaker, Woofer Pairing button LED Indicator

SOUND

MODE

PAIR

5 Sec

Red → Green → Blue Blinks

Pairing

Connection is complete

Cyan Blinks X3

4. Check if the LINK LED is solid blue (connection complete).

Front of the Wireless Subwoofer

Stops blinking.

Glows blue.

The LINK LED indicator stops blinking

and glows a solid blue when a

connection is established between the

Soundbar and the Wireless Subwoofer.

NOTES

– Do not connect the power cord of this product or your TV to a wall outlet until all connections

between components are complete.

– Before moving or installing this product, be sure to turn off the power and disconnect the power cord.

– The maximum transmission distance of the wireless signal of the main unit is about 10 m, but may

vary depending on your operating environment. If a steel-concrete or metallic wall is between the

main unit and the wireless subwoofer, the system may not operate at all, because the wireless

signal cannot penetrate metal.

PRECAUTIONS

– Wireless receiving antennas are built into the wireless subwoofer. Keep the units away from water

and moisture.

– For optimal listening performance, make sure that the area around the wireless subwoofer and

Wireless Receiver Module (Sold separately) is clear of any obstructions.

La page charge ...

Samsung HW-S61T Manuel utilisateur

Samsung HW-S61T Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents