Northern Lights AVALANCHE4 MULTI-GYM Assembly Instructions Manual

Marque
Northern Lights
Modèle
AVALANCHE4 MULTI-GYM
Catégorie
Fitness, gymnastique
Taper
Assembly Instructions Manual
AVALANCHE4 MULTI-GYM
ASSEMBLY INSTRUCTIONS
AVALANCHE4 Multi Gym, 150lb
MG-AVALANCHE4
Overall Dimensions: 94.5" L x 48" W x 82.25" H
March 14, 2006
Specifications
Weight = 531.5 lbs
Packed in 7 Boxes
Box 1 = 23.5" x 20.5" x 7.5"
= 2.09 ft3
= 67 lbs
Box 2 = 55.5" x 18" x 13.5"
= 7.80 ft3
= 105.5 lbs
Box 3 = 52.75" x 40" x 6.5"
= 7.94 ft3
= 84 lbs
Box 4 = 80" x 36" x 7"
= 11.67 ft3
= 125 lbs
Box 5, 6 & 7
= 11.75" x 5.25" x 5.25"
= 0.187 ft3
= 50 lbs (each)
2
Item Description........................... Qty.... Bag #
AU Top Beam Cable......................1.........1
AV Lower Cable.............................1.........1
Item Description........................... Qty.... Box #
1Base ........................................1.........4
2Rear Upright.............................1.........4
3Lower Press Arm Support ........1.........1
4Lower Press Arm .....................1.........1
5Press Arm Outer Tube..............1.........2
6Main Upright.............................1.........4
7Upright to Base Bracket ...........2.........1
8Upper Guide Rod Support. .......1.........3
9Weight Stack Support...............1.........1
10 Seat Support Assy ...................1.........2
11 Selector Pin .............................1..... Bag 1
16 Leg Extension Assy..................1.........2
17 Top Bracket .............................2.........2
19 Press Arm Adjustment Tube .....1.........2
20 Press Arm................................1.........3
21 Back Rest Support ...................1.........1
22 Low Row Pulley Bracket ...........1.........4
Parts list
Item Description..............................Qty....Box #
23 Left Swing Arm............................1....... 3
24 Right Swing Arm..........................1....... 3
25 Arm Support ................................1....... 3
26 Guide Rod ...................................2....... 4
27 Top Bracket Spacer 5/8" x 4" ......1....Bag 1
28 Knee Roller Support ....................1....... 1
29 Low Row Calf Raise Attach. ........1....... 1
30
Top Pulley Spacer 5/8" x 1-11/16" ....
2....Bag 1
32
Weight Stack Selector Rod Assem
....1....... 1
33 Cable Retainer ............................4....... 1
34 Pulley Bracket (4- 9/16") ..............2....... 1
35 Lat Bar Hooks (L&R) ...................2....... 1
36 18" Straight Bar...........................1....... 3
37 48" Lat Bar..................................1....... 3
38 Weight Stack Plate ......................15......
3x50#
39 Foam Rollers ...............................4....... 3
40 Foam Rollers 5 inch.....................2....... 3
41 Back Rest Small ..........................1....... 3
42 Back Rest Large .........................1....... 3
43 Seat Pad.....................................1....... 3
44 Leg Extension Roller Tube...........1....... 1
45 Weight Stack Shroud ...................1....... 4
46 Wt. Stack Front Shroud R&L ........2....... 4
IMPORTANT - Please record the product's
Lot No.'s (found on the box label) onto
the warranty form for your records.
3
Item Description..............................Qty.Bag #
AA 1/2" thk spacer ..........................40 ...... 2
AB 1-1/2" Plastic Cap - Sq Internal ..1......... 4
AC 2" Plastic Cap - Sq Internal ........13....... 4
AD 2"x 4" Plas. Cap - Rect Intern .....2......... 4
AF Foam Roller Caps .....................6......... 4
AG Rubber Cushion 10-1/4" ............1......... 1
AH Rubber Cushion 3/4"thk 2" .........2......... 1
AI Plastic Rod Support ..................1......... 1
AJ 3-1/2" Pulley ..............................17....... 3
AK 22" Chain ..................................1......... 1
AM Ankle Cuff ..................................1......... 1
AN Rubber Grip 5" x 1-1/4"..............6......... 4
AO Rubber Grip 8-1/2" ....................4......... 4
AP Rubber Spacer 3/8"thk 2" ..........2......... 1
AQ Edge Trim 20-1/4" .....................1......... 4
AR Edge Trim 36"...........................2......... 4
Parts List (cont.)
Item Description ...............................Qty Bag #
A3/8" x 1" Bolt.............................6...... 2
B3/8" x 1-1/4" Bolt.......................1...... 2
D3/8" x 1-3/4" Bolt.......................6...... 2
E3/8" x 2-1/2" Bolt.......................1...... 2
F3/8" x 3" Bolt.............................7...... 2
G3/8" x 3-3/4" Bolt.......................2...... 2
H3/8" x 5" Bolt............................16..... 2
I3/8" x 5-1/2" Bolt.......................5...... 2
J3/8" x 6" Bolt.............................1...... 2
K3/8" Locknut Thin......................3...... 2
L3/8" Locknut ............................38..... 2
M3/8" Plate Washer ...................40..... 2
N1/4" x 2-1/2" Bolt.......................4...... 2
O1/4" Acorn Nut ..........................4...... 2
P1/2" x 4" Bolt.............................1...... 2
Q1/2" x 5" Bolt.............................1...... 2
R1/2" x 5-1/2" Bolt.......................1...... 2
S1/2" x 6" Bolt.............................1...... 2
T1/2" Locknut .............................4...... 2
V3/4" x 5-1/2" Bolt.......................1...... 2
W3/4" Locknut .............................1...... 2
X3/8" x 5/8" Flat Head Bolt..........2...... 1
Y3/8" x 4-1/2" Bolt.......................2...... 2
Items on this page are contained in
bags packed in Box #1.
4
2
1
10
37
43
42
41
39
40
35
36
21
24
23
34
27
22
28
6
25
29
3
4
5
7
33
AG
AH
32
38
26
AI
19 8
17
20
16
30
44
11
9
45
46 R
46 L
5
1
2
6
28
22
29
7
8
17
27
H
H
M
LTYPICAL UNLESS
NOTED
ONLY WHERE
SHOWN
I
H
H
F
AC
AC
AC
AC
AC
1. Attach the Rear Upright (2) to the Base(1).
2. Attach the Main Upright(6) to the Base(1)
using the Upright to Base Brackets(7).
3. Install the Top Brackets(17) & the Upper
Guide Rod Support(8) to the Main Upright(6)
& the Rear Upright(2). Do not tighten the three
(3) bolts (I) holding the Upper Guide Rod
Support(8) until the Weight Stack has been
installed.
4. Attach the Knee Roller Support(28) to the
Main Upright(6).
5. Remove the 5/8" Locknut from the shoulder bolt in the Base(1), position the Low Row Pulley Bracket(22)
over the shoulder bolt and replace the Locknut. Do not over tighten the Locknut.
6. Attach the Low Row Calf Raise Attachment(29) to theBase(1).
NOTE: THE LOW ROW CALF RAISE ATTACHMENT CAN BE CONNECTED TO BASE IN THIS STEP
OR CAN BE CONNECTED AT A LATER TIME, TO ALLOW FOR ADDITIONAL WORKING SPACE.
7. Insert plastic caps(AC & AD) where shown.
AD
6
10
1
16
AC
AC
AC
E
L
M
F
ONLY WHERE
SHOWN
TYPICAL UNLESS
NOTED
F
8. Attach the Leg Extension Assembly (16) to the Base(1).
9. Attach the Seat Support Assembly(10) to the Main Upright(6) & Leg Extension Assembly(16).
10. Insert plastic caps(AC) where shown.
6
7
11. Place Weight Stack Support(9), Rubber Cushion 10-1/4"(AG) & two(2) Rubber Cushions 3/4"thk x
2"(AH) over holes in the base of the Rear Upright(2) and slide both Guide Rods(26) into them. NOTE: For
improved performance, we recommend you apply a silicone lubricant to the guide rods prior to their installation.
12 . Leaning the Guide Rods(26) toward you, slide the fifteen(15) Weight Stack Plates(38) onto Guide
Rods(26).
13. Slide the Weight Stack Selector Rod Assembly(32) over the Guide Rods(26) and onto the Weight Stack
Plates(38).
14. Slide the Plastic Rod Support(AI) onto Guide Rods(26) and bolt to the Upper Guide Rod Support(8).
Tighten the three (3) bolts holding the Upper Guide Rod Support(8) which were previously left loose on Pg 5.
15. Install Edge Trim 20-1/4"(AQ) on Weight Stack Shroud(45) & two(2) Edge Trims 36"(AR) on Wt. Stack
Front Shrouds R&L(46).
16. Bolt Weight Stack Shroud(45) and Wt. Stack Front Shrouds R&L(46) to Rear Upright(2) using bolting
shown. Install 2" Plastic Cap(AC) where shown.
AG
AH
2
26
38
32
AI
8
X
9
AQ
AR
45
46
R
46
L
AC N
O
4 PLACES
4 PLACES
8
17.Attach the Lower Press Arm Support(3)
to the Base(1).
18. Attach the Lower Press Arm(4) to the
Rear Upright(2).
19. Slide the Press Arm Adjustment Tube(19)
into the Press Arm Outer Tube(5). Attach the
Press Arm Outer Tube(5) to the Lower Press
Arm(4).
20. Attach the Press Arm(20) to the Rear
Upright(2).
21. Attach the Press Arm
Adjustment Tube(19) to the
Press Arm(20).
22. Insert plastic caps(AC)
where shown.
23. With the Press Arm at its lowest position,
screw the pop pin internals which are attached
to the end of the press arm cable into pop pin
outer sleeve on the Press Arm Outer
Tube(5) and tighten securely. Position the
threaded part of the cable into the slot of the
cable retainer which is attached to the Press
Arm Outer Tube(5); the two jam nuts must
stradle the cable retainer. Remove any slack
from the steel cable to the pop pin and tighten
the two jam nuts against the cable retainer.
3
1
4
2
19
5
20
AC
V
W
R
T
S
H
M
L
P
BOTH SIDES
POP PIN
CABLE
RETAINER
JAM NUTS
PRESS ARM
CABLE
5
NOTE: Do NOT over tighten bolted connections
where bronze bushings are used.
AC
AC
24. Install the Arm Support(25), Pulley(AJ) and six(6) 1/2" thk spacers(AA) between the Top
Brackets(17). Install the plastic cap(AB) where shown.
25. Remove the two(2) 5/8" Locknuts from the shoulder bolts in the Arm Support(25), position the
Left & Right Swing Arms(23 & 24) over the shoulder bolts and replace the Locknut. Do not over
tighten the Locknut.
25
17
24
23
AJ
AA
AB
QH
L
T
9
10
AU
AV
35
35
34
33
AJ
H
D
D
AA
LTYPICAL UNLESS
NOTED
M
30
TYPICAL
Y
R
ONLY WHERE
SHOWN
L
AD AA
AA
BOTH SIDES
26. Install the Top Cable(AU)
starting at the front. Take care to
keep the cable in the pulley
grooves. Do not connect to the
Selector Rod Assy(32) until the
Lower Cable(AV) has been
installed.
27.After installing the Lower
Cable(AV), see page 11,
connect Top Cable(AU) and
Lower Cable(AV) using two
Pulley Brackets(34).
32
GAA
If a Multi-Gym Leg Press Option or Pivot
Leg Press Option is being installed,
cable(AV) must be replaced with
cable(AA) which is included in the Leg
Press Option Kit or Pivot Leg Press
Option Kit for MG-AVALANCHE.
ATTENTION!
K
11
28. Install the Lower Cable(AV)
starting at the Low Row Pulley
Bracket(22).
29. Complete the installation of
theTop Cable(AU) by threading
the end of the cable into the
Weight Stack Selector Rod
Assembly(32) until slackness in
the cables is removed. Tighten
the jam nut against the Weight
Stack Selector Rod Assembly.
Periodic cable tightening may be
required.
22
AA
L
MONLY WHERE
SHOWN
25
I
H
KL
F
B
AA AJ
TYPICAL
AA
D
While the hollow bolt provides approximately 1-1/4" adjustment, 3/8" thick
Rubber Spacers 3/8"thk x 2"(AP) have been provided to give further
cable adjustment. These spacers can be used by themselves or in
addition to Rubber Cushions 3/4"thk x 2"(AH) which were installed on
Page 7.
32
Jam Nut
AV
AU
AV
11
12
30. Attach the Back Rest Small(41) to the Back Rest Support(21) then attach them to the Main Upright(6)
making sure that the back adjustment tab is positioned in the main upright openings.
31. Attach the Back Rest Large(42) and the Seat Pad(43) to the Seat Support Assy(10).
32. Select the location for the Leg Extension Roller Tube(44). Slide on all Foam Rollers(39) and Foam Rollers
5"(40). Insert the Foam Roller Caps(AF).
33. Slide on the Rubber Grips(AN & AO) where shown. Grips slide on easiest when a solution of soapy water
is first applied to the bar. This will dry in a short time and causes no damage to the machine. Do NOT use any other
lubricant.
NOTE: Make certain that all cables are properly positioned on/around pulleys before use and that all
nuts have been tightened.
21
37
36
39
40
41
42
43
AO
AO
AO
AO
AN
AN
AN
AN
AF
AF
AF AF
A
A
44
6
J
10
40
L
Cables are a consumable and must be treated as such. As a minimum, an annual inspection must
be performed on all cable ends and full lengths. A cable must be replaced immediately if broken
exposed wires and/or a break in cable coating are found.
NORTHERN LIGHTS
FITNESS PRODUCTS INC.
Dear Customer:
Thank you for selecting Northern Lights Exercise Equipment. We hope
that you will enjoy and benefit from your new fitness product for years
to come. If you have any questions regarding your new equipment or
would like to find out what other products are available to add to your
workout, feel free to contact the authorized Northern Lights showroom
in your area.
WARRANTY
Manufacturer’s Limited Lifetime Warranty
Northern Lights Fitness Products Inc. offers its customers a lifetime
warranty against broken welds and manufacturer defects on all prod-
ucts. Simply return the defective part, insured and prepaid to Northern
Lights and we will replace it at no charge.
This warranty is for original product owners and does not cover damage
resulting from product alterations, misuse, abuse, improper assembly,
normal wear and tear or other conditions, which are beyond our control.
No other express warranty has been made or will be made on behalf of
Northern Lights with respect to any Northern Lights product or the
operation, repair or replacement of any Northern Lights product. North-
ern Lights shall not be responsible for injury, loss of use of the product,
inconvenience, loss or damage to personal property, whether direct or
indirect.
This warranty does not include any implied warranties or liability for
incidental or consequential damages created by any provincial or state
law.
If you feel that a Northern Lights product is defective, please contact
our parts department at (800) 461-1709.
NORTHERN LIGHTS
FITNESS PRODUCTS INC.
Cher Client:
Merci d’avoir sélectionneé un produit Northern Lights. Nous espérons
que vous aimerez et bénéficierez de votre nouveau produit pour des
années à venir. Si vous avez des questions concernant votre nouveau
produit ou si vous aimeriez trouver d’autres produits disponible de
Northern Lights, contactez un détaillant autorisé Northern Lights.
La GARANTIE
Garantie à Vie Limitée du Fabricant
Northern Lights Fitness Products Inc. offre à ses clients une garantie à
vie contre toutes soudures casées et contre tout défaut de matériau et
de fabrication dans le cadre d’un entretien soigneux et d’une utilisation
conforme à l’usage prévu réalisée dans des conditions normales.
Simplement, retrournez la pièce défectueuse à Northern Lights, payé et
ensuré, et nous la remplacerons sans frais.
Cette garantie s’étend uniquement au propriétraire d’origine seulement
et n’est pas transferable. Elle ne couvre pas les produits soumis à une
mauvaise utilisation, à un manque de soins, à des accidents, à des
réparations ou à des modifications non autorisées.
Aucune autre garantie n’a été faite ou sera faite de la part de Northern
Lights en ce qui concerne tout produit de Northern Lights ou son
opération, réparation ou échange. Northern Lights ne sera pas
responsable pour blessure, perte d’usage du produit, dérangement,
perte ou dommage de propriété personnelle, direct ou indirect.
Cette garantie n’inclut pas toutes autres garanties implicites pour
incidents ou dommages conséquents créés par les lois provincial ou les
lois d’état.
Si un produit de Northern Lights est défectueux, s’il vous plaît contactez
notre département de Pièces et Service au (800) 461-1709.
Please record Lot No.'s from the box labels
here and retain for any future warranty
claim:
Box 1-
Box 2-
Box 3-
Box 4-
Box 5-
Box 6-
Box 7-
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Northern Lights AVALANCHE4 MULTI-GYM Assembly Instructions Manual

Marque
Northern Lights
Modèle
AVALANCHE4 MULTI-GYM
Catégorie
Fitness, gymnastique
Taper
Assembly Instructions Manual
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents