Bercomac 700416 Manuel utilisateur

Marque: Bercomac

Modèle: 700416

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Ce manuel convient également à

700400-1

OWNER’S MANUAL

Model Number

700400-1

Berco

Northeast Two Stage 48’’ Snowblower

for

TRACTORS WITH 2000 R.P.M. P.T.O. DRIVE

CAUTION:

READ & FOLLOW ALL SAFETY RULES & INSTRUCTIONS BEFORE

OPERATING YOUR EQUIPMENT

104776 I-10

* ASSEMBLY * REPAIR PARTS

* OPERATION * MAINTENANCE

*104776*

LIMITED WARRANTY

Bercomac Limitée

92, Fortin Nord, Adstock, Québec, Canada, G0N 1S0

Conditions and Products Covered:

BERCOMAC guarantees any part of the product or accessory

manufactured by BERCOMAC and found in the reasonable

judgment of BERCOMAC to be defective in material and or

workmanship will be repaired or replaced by an authorized

dealer without charge up to our maximum labor rates and pre-

established times. For replacement parts only standard

ground freight services are covered. This warranty extends to

the original retail purchaser only and is not transferable to any

subsequent purchasers.

Warranty Period

(from date of the original retail purchase):

x Residential use: 1 year

x Commercial or rental use: 90 days

Exceptions Noted Below: the following items are

guaranteed by the original manufacturer and have their own

warranty, conditions and limited time:

x Tire Chains: 90 days

x Engines (installed in factory on BERCO equipment): 2

years

x Engines (sold separately): Validate with the dealer.

Please refer to the engine manufacturer’s warranty

statement included with the unit. BERCOMAC is not

authorized to handle warranty adjustments on engines.

Items and Conditions NOT Covered:

This warranty does not cover the following:

x Pick-up or delivery charges or in-home services fees.

x Any damage or deterioration of the unit, parts and or finish

of these due to normal use, wear and tear, or exposure.

x Cost of regular use or maintenance service or parts, such

as gas, oil, lubricants, tune-up parts, and adjustments.

x Any part or accessory which has been altered, modified,

misused, neglected, accidentally damaged or not properly

installed, maintained, stored or repaired not in accordance

with the instructions in the owner’s manual.

x Repair due to normal wear and or any wear items such as

shear pins, bolts, belts, etc.

x Expedited freight fee services for replacement parts.

x Shear bolts and shear pins are to be considered as a

preventive measure not as an assured protection, any

damages resulting from the lack of shear bolts breakage

are not covered.

NOTE: All warranty work must be performed by an authorized

dealer using original (manufacturer) replacement parts.

Owner’s Responsibilities:

BERCOMAC’s defective equipment or part must be returned

to an authorized dealer within the warranty period for repairs.

In the event that defective merchandise must be returned to

manufacturer for repairs, freight fees are prepaid and a

written authorization from BERCOMAC must be obtained by

dealer prior to the shipment. This warranty extends only to

equipment operated under normal conditions. To validate a

warranty claim, it is the user’s responsibility to maintain and

service the unit as specified in the owner’s manual or to

have the unit serviced at their dealer at their expense.

General Conditions:

The sole liability of BERCOMAC with respect to this warranty

shall be strictly and exclusively repair and replacement as

mentioned herein. BERCOMAC shall not have any liability

for any other costs, loss or damage, including but not limited

to, any incidental or consequential loss or damage.

In particular, without being limited to, BERCOMAC shall have

no liability or responsibility for:

x Travel time, overtime, after hours time or other

extraordinary repair charges or relating to repairs and or

replacements outside of normal business hours.

x Rental of like or similar replacement equipment during the

period of any, repair or replacement work.

x Any communicating or travel charges.

x Loss or damage to person or property other than that

covered by the terms of this warranty.

x Any claims for lost revenue, lost profit or any similar costs

as a result of damage or repair.

x Attorney’s fees.

BERCOMAC’s responsibility in respect to claims is limited to

making the required repairs or replacement without charge

up to our maximum labor rates and pre-established times

and no claim of breach of warranty shall be cause for

cancellation or rescission of the contract of sale of any

product or accessory.

This warranty gives you specific legal rights. You may also

have other rights, which vary from state to state.

Note: Bercomac reserves the right to change or improve the design of any part or accessory without assuming any obligation to modify

any product previously manufactured.

Instructions for Obtaining Warranty Services:

Contact dealer where equipment was purchased or any other BERCOMAC Service Dealer to arrange service at their dealership. To

locate a dealer convenient to you, access our website at www.bercomac.com.

Bring the product and your proof of purchase (sales receipt) to the BERCOMAC dealer.

INTRODUCTION ...................................................................................................................................... 2

SAFETY PRECAUTIONS ......................................................................................................................... 3

SAFETY DECALS ..................................................................................................................................... 5

ASSEMBLY

Tools Required ................................................................................................................ 6

Step 1: Chute installation ............................................................................................................. 6

Step 2: Snowblower Preparation ................................................................................................. 7

Step 3: Snowblower Installation ................................................................................................... 8

OPERATION

Snowblower Operation ................................................................................................................. 10

Controls ........................................................................................................................................ 10

Snow Removal ............................................................................................................................. 10

Clearing a Clogged Discharge Chute .......................................................................................... 10

MAINTENANCE

Maintenance ................................................................................................................................ 11

Adjustments ................................................................................................................................. 11

Lubrication ................................................................................................................................... 11

Cutting Edge Maintenance ........................................................................................................... 11

Snowblower Pulley Replacement or Alignment ........................................................................... 11

Auger and Fan Shear Bolt Replacement ..................................................................................... 11

Belt Replacement ......................................................................................................................... 12

Belt Adjustment ............................................................................................................................ 12

DISMOUNTING & STORAGE

Snowblower Dismounting ............................................................................................................ 13

Subframe Dismounting ................................................................................................................ 13

End of Season Storage ................................................................................................................ 13

TROUBLESHOOTING .............................................................................................................................. 14

TORQUE SPECIFICATION TABLE .......................................................................................................... 15

PARTS BREAKDOWN & LISTS

Chute with Rotation System ......................................................................................................... 16

Snowblower ................................................................................................................................. 18

OPTIONS & ATTACHMENTS ............................................................................................... 22

TABLE OF CONTENTS

Page

INTRODUCTION

TO THE PURCHASER

This new attachment was carefully designed to give years of dependable service. This manual has been provided to

assist in the safe operation and servicing of your attachment.

NOTE: All photographs and illustrations in the manual may not necessarily depict the actual models or attachment, but

are intended for reference only and are based on the latest product information available at the time of publication.

Familiarize yourself fully with the safety recommendations and operating procedures before putting the machine to use.

Carefully read, understand and follow these recommendations and insist that they be followed by those who will use

this attachment.

THIS SAFETY ALERT SYMBOL IDENTIFIES AN IMPORTANT SAFETY MESSAGE IN THIS MANUAL

THAT HELPS YOU AND OTHERS AVOID PERSONAL INJURY OR EVEN DEATH. DANGER,

WARNING, AND CAUTION ARE SIGNAL WORDS USED TO IDENTIFY THE LEVEL OF HAZARD.

HOWEVER, REGARDLESS OF THE HAZARD, BE EXTREMELY CAREFUL.

DANGER: Signals an extreme hazard that will cause serious injury or death if recommended precautions are

not followed.

WARNING: Signals a hazard that may cause serious injury or death if the recommended precautions are not

followed.

CAUTION: Signals a hazard that may cause minor or moderate injury if the recommended precautions are not

followed.

Record your attachment serial number and purchase date in the section reserved below. Your dealer requires this

information to give you prompt, efficient service when ordering replacement parts. Use only genuine parts when

replacements are required.

If warranty repairs are required please present this registration booklet and original sales invoice to your selling dealer

for warranty service.

This manual should be kept for future reference.

Please check if you have received all the parts for your kit with the list of the

bag and the list of the box.

SERIAL NUMBER : ___________________________

PURCHASE DATE : ___________________________

SAFETY PRECAUTIONS

Careful operation is your best insurance against an accident. Read this section carefully before operating the vehicle

and accessory. This accessory is capable of amputating hands and feet and throwing objects. Failure to observe the

following safety instructions could result in serious injury. All operators, no matter how experienced they may be,

should read this and other manuals related to the vehicle and accessory before operating. It is the owner's legal

obligation to instruct all operators in safe operation of the accessory.

GLOSSARY:

In this manual, right and left sides are determined by

sitting on the seat of the vehicle facing forward.

In this manual, "accessories" means attachments

(snowblower, rotary broom, blade etc.) that you install

on the vehicle (lawn tractors, A.T.V. s etc).

TRAINING:

This symbol, "Safety Alert Symbol", is used

throughout this manual and on the accessory’s

safety labels to warn of the possibility of serious

injury. Please take special care in reading and

understanding the safety precautions before

operating the vehicle and accessory.

1. Read this owner's manual carefully. Be thoroughly

familiar with the controls and proper use of the

vehicle and accessory. Know how to stop the unit

and disengage the controls quickly.

2. Never allow children to operate the vehicle nor the

accessory. Never allow adults to operate the vehicle

nor the accessory without proper instructions.

3. No one should operate the vehicle nor the

accessory while intoxicated or while taking

medication that impairs the senses or reactions.

4. Keep the area of operation clear of all people,

particularly small children and pets.

PREPARATION:

1. Thoroughly inspect the area where the accessory

is to be used and remove door mats, all foreign

objects and the like.

2. For motorized accessories, disengage all clutches

and shift into neutral before starting engine.

3. Do not operate the accessory without wearing

adequate winter outer garments. Avoid loose fitting

clothing that can get caught in moving parts. Wear

footwear that will improve footing on slippery

surfaces.

4. Handle fuel with care, it is highly flammable.

a) Use approved fuel container.

b) Never add fuel to a running engine or hot engine.

c) Fill fuel tank outdoors with extreme care. Never fill

fuel tank indoors.

d) Never fill containers inside a vehicle, or on a

truck or a trailer bed with a plastic liner. Always

place containers on the ground, away from your

vehicle, before filling.

e) When practical, remove gas-powered

equipment from the truck or trailer and refuel it

on the ground. If this is not possible, then refuel

such equipment on a trailer with a portable

container, rather than from a gasoline

dispenser nozzle.

f) Keep the nozzle in contact with the rim of the

fuel tank or container opening at all times, until

refueling is complete. Do not use a nozzle lock-

open device.

g) Replace fuel cap securely and wipe up spilled

fuel.

h) If fuel is spilled on clothing, change clothing

immediately.

5. Never attempt to make any adjustments while the

engine (motor) is running (except when specifically

recommended by manufacturer).

6. Let the vehicle and accessory adjust to outdoor

temperatures before starting to clear snow.

7. Always wear safety glasses or eye shields during

operation or while performing an adjustment or

repairs to protect the eyes from foreign objects that

may be thrown from the accessory.

8. Never modify the accessory or any part without

the written consent from the manufacturer.

SAFETY PRECAUTIONS

OPERATION:

1. Do not put hands or feet near, under or inside

rotating parts.

2. Exercise extreme caution when operating on or

crossing gravel drives, walks or roads. Stay alert for

hidden hazards or traffic. Do not carry passengers.

3. After striking a foreign object, stop the engine

(motor), disconnect the wire from the spark plug(s)

and keep wire away to prevent accidental starting.

Thoroughly inspect the accessory for any damage

and repair damage before restarting and using the

accessory.

4. If the unit should start to vibrate abnormally, stop

the engine (motor) and check immediately for the

cause. Vibration is generally a warning of trouble.

5. Take all possible precautions when leaving the

vehicle unattended. Disengage the power take-off,

lower the attachment, place the transmission into

neutral, set the parking brake, stop the engine and

remove the contact key.

6. Do not run the engine indoors, except when

starting the engine and for transporting in or out of

the building. Do not operate or let motor run in a

storage area without ventilation because gas

contains carbon monoxide which is odorless,

colorless and can cause death.

7. Never clean across the face of slopes, go from top

to bottom. Exercise extreme caution when using

equipment on slopes. Do not attempt to clear a

steep slope.

8. Never use an accessory without proper guards,

plates, or other safety protective devices in place

9. Never tolerate bystanders in the working zone.

Never use an accessory in the direction of

bystanders, it might throw gravel or debris that can

hurt people or damage property.

10.Never operate the accessory at high transport

speeds on slippery surfaces. Use care when

backing up.

11.Do not carry passengers.

12.Disengage power to the accessory when it is

transported or not in use.

WHENEVER YOU SEE THIS SYMBOL

IT MEANS:

WARNING!

BECOME ALERT !

YOUR SAFETY IS INVOLVED!

MAINTENANCE AND STORAGE

1.When cleaning, repairing or inspecting the vehicle

and accessory, make certain that all moving parts

have stopped. Disconnect wire from the spark plug

(s) and keep wire away to prevent accidental

starting.

2. Check all the bolts at frequent intervals to make

sure that they are properly tightened .

3. Never store a motorized accessory with fuel in the

fuel tank inside a building where ignition sources

are present such as hot water and space heaters,

clothes dryers, and the like. Allow the engine to cool

before storing in any enclosure.

4. Always refer to the owner’s manual when you store

the accessory and vehicle for a prolonged or an

unspecified length of time.

5. Maintain or replace safety and instruction labels, as

necessary.

6. For winter accessories, (if applicable), let the engine

run for a few minutes after clean snow in order to

prevent the rotary parts from freezing.

7. Inspect the vehicle’s and accessory’s air filter every

day. Clean it or replace it as necessary. Change the

oil more often when working in dusty conditions.

See the vehicle’s and accessory's owner’s manual.

13.Never operate the accessory without good visibility

or light.

14.Keep the accessory away from heat sources or

flames.

15.Always wear a dust mask when working in a dusty

environment.

SAFETY DECALS

REPLACE IF DECALS ARE DAMAGED

SEE PARTS BREAKDOWN FOR DECAL LOCATION

Decal # 104243

Decal # 102126 Decal # 102127

Decal # 102190 Decal # 104245 Decal # 102113

Decal # 103951 Decal # 102125

ASSEMBLY

Install the hand guard (item 1) in the chute (item 2) as

shown.

Secure in place with two 1/4 x 3/4" hex bolts, two flat

washers and two 1/4’’ flange nuts on the inside.

Tighten firmly.

Install chute

Install hand guard

Before installing the chute (item 1), loosen the two

flange nuts (item 2) (down to the last threads) which

holds the rotation system (item 3).

Install the rotation ring (item 4) over opening (item 5)

as shown and align the notches.

Place the chute (item 1) (facing the rear) and clip the

back over the rotation ring then turn the chute

towards the front to lock into place.

Reinstall the rotation system by tightening the flange

nuts firmly.

STEP 1

CHUTE INSTALLATION:

Refer to parts breakdown section for parts identification.

IMPORTANT: TORQUE ALL BOLTS ACCORDING TO

TORQUE SPECIFICATION TABLE (SEE TABLE OF

CONTENTS), WHEN STATED: TIGHTEN FIRMLY.

TOOL REQUIRED:

Ratchet

Sockets: 7/16’’, 1/2’’

Wrench: 7/16’’

Hexagonal wrench: 3/16’’

STEP 2

SNOWBLOWER PREPARATION:

ASSEMBLY

Remove the driveline guard (item 1) by removing the

two 5/16” x 3/4” hex bolts (item 2) and lock washers

(item 3).

Install the guard extension (item 10) as described in the

owner’s manual for the half driveline kit or for the sub-

frame.

Install the driveline (item 4) on the snowblower input

shaft (item 5) with a hex. bolt 1/4” n.c. x 2" (item 6),

nylon insert lock nut (item 7) and key 1/4” x 1/4” x

1" (item 8).

Tighten the bolt and set screw very firmly.

Flip the P.T.O. support (item 9) upward as shown.

This support helps hold the driveline and snowblower

to facilitate installation on the frame.

Put back the driveline guard (item 1) in place.

Tighten the 5/16" x 3/4” hex. bolts (item 2) and lock

washers (item 3) firmly.

Install the driveline

STEP 3

SNOWBLOWER INSTALLATION:

Refer to parts breakdown section for parts

identification.

ASSEMBLY

Install handle

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

Install the driveline section

(Female / male 1’’, 15 splines)

Install the driveline section (item 4) from separate kit,

into the snowblower’s driveline (item 3) by aligning the

stamped marks (item 2) (located between the splines

at the end of the shaft) with the large groove (item 1)

in the hollow tube on the snowblower’s section.

Only one position allows the sections to be inserted

one into the other.

Attach the snowblower to the subframe by inserting

the snowblower’s male hitch (item 1) into the pivot

support (item 2).

Make sure the male hitch is entered to its maximum

and locked in place by the springs (item 3).

Connect the rotary driveline to the tractor P.T.O. spline

shaft.

Make sure the driveline yoke is securely attached

to the tractor P.T.O.

Install 1/2 x 3’’ handgrip (item 1) on the handle (item

2).

Insert the handle through the grommet in the rotation

support (item 3).

Install the handle extension (item 4) (included with the

subframe) in the rotation handle with a 2.5 mm hair

pin (item 5).

Install the handle hook (item 6) on the rotation worm.

Insert hook into the handle and lock in place with a

2.5 mm hair pin (item 7).

Install the snowblower

ASSEMBLY

VERIFY SKID SHOE ADJUSTMENT:

LEVEL PAVED SURFACE: Adjust skid shoes to allow

3/16" to 1/4" clearance (A) between cutting edge and

surface.

UNEVEN OR GRAVEL SURFACE: Adjust skid shoes

to allow 1/2" to 5/8" clearance (A) between cutting

edge and surface.

VERIFY TIRE PRESSURE:

Check and adjust tractor tire pressure as follows:

Front tires: 14-15 psi

Back tires: 7-8 psi

Tire pressure must be even on both sides of tractor.

Adjust skid shoes

DANGER

ROTATING DRIVELINE

Contact can cause death.

KEEP AWAY

Do not operate without:

All driveline, tractor & equipment shields in

place.

Driveline securely attached at both ends.

DANGER

If the driveline is not completely covered, be sure

a guard extension is installed.

Do not operate without driveline completely cov-

ered by the shield.

SNOWBLOWER OPERATION

a) Make sure the snowblower is clear of snow

before engaging the snowblower.

b) Make sure that the auger and impeller operate

freely.

c) Start the tractor engine.

d) Before engaging the snowblower drive, always

have the engine running at medium R.P.M.

e) Operate the snowblower at maximum engine

R.P.M.

IMPORTANT: USE FULL ENGINE R.P.M. WHEN

REMOVING WET OR STICKY SNOW. LOW R.P.M.

WILL TEND TO PLUG THE CHUTE.

CONTROLS

CHUTE ROTATION

The chute rotation handle is located to the left of

steering wheel. Turning the handle in a clockwise

direction, the discharge chute will turn in a clockwise

direction or vice versa.

CHUTE DEFLECTOR

Set the angle of the deflector according to the distance

the snow must be thrown and to prevent property

damage. To change the deflector angle, loosen the two

deflector knobs & adjust the deflector to the appropriate

angle and retighten the two knobs securely.

SNOW REMOVAL

When removing snow, do not use the snowblower as

a dozer blade to push snow. Allow snowblower to

ingest snow at its own speed. If the speed of your

tractor is too fast, the snowblower may become

overloaded and plug. For best results, raise the

snowblower and remove a top layer of snow. A

second pass with the snowblower will remove the

remaining snow.

IMPORTANT:

Use full engine R.P.M. when removing wet, sticky

snow. Low R.P.M. power will tend to plug the

chute.

OPERATION

WARNING

-Do not attempt to clear plugged chute, auger or

fan of snow while tractor engine is running.

-Disengage snowblower.

-Lower snowblower onto ground.

-Set the parking brake.

-Stop engine, remove the ignition key, disconnect

the wire from spark plug(s) and keep away from

spark plug(s) to prevent accidental starting.

-Make sure all moving parts have stopped.

-Do not use hand to unplug chute. Use a 36’’ (924

mm.) minimum length stick or board.

WARNING

Read the tractor Owner’s Manual carefully. Be

thoroughly familiar with the controls & proper

use of the attachment. Know how to stop the

attachment & disengage the controls quickly.

WARNING

TO PREVENT INJURIES AND FOR MORE

TRACTION WHEN USING AN ATTACHMENT:

-Rear counterweight of 100 lbs. minimum is

required to counterbalance the attachment’s

weight.

-Tractor manufacturer approved tire chains are

required.

-Do not operate on a slope greater than 10°.

-When dismounting the attachment remove rear

counterweights.

CLEARING A CLOGGED DISCHARGE

CHUTE:

Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowblowers. Never use your hand to

clean out the discharge chute.

To clear the chute:

1. Lower snowblower to the ground and set parking

brake.

2. SHUT THE ENGINE OFF & REMOVE KEY!

3. Wait 10 seconds to be sure the all moving parts

such as the impeller blades have stopped moving.

4. Disconnect wire from the spark plug(s) and keep

wire away to prevent accidental starting.

5. Always use a clean-out tool of at least 36” in length,

NOT YOUR HANDS.

AUGERS AND FAN SHEAR BOLT

REPLACEMENT

Shear bolts are to be considered a preventive

measure and not an assured protection. Operator

vigilance is required. Thoroughly inspect the areas

where the snowblower is to be used and remove all

foreign objects.

To avoid damage to the snowblower:

Use only the original shear bolts (grooved bolts).

#104000 in bags of 10 for the augers.

#103999 in bags of 10 for the fan.

Reinstall auger in the position shown.

The use of any other shear bolt will not insure any

protection and may void the warranty.

MAINTENANCE

a) Check mounting bolts at frequent intervals for

proper tightness in order to prevent costly repairs.

Make sure your snowblower is in safe working

condition.

b) Provide adequate blocking before working under

snowblower when in raised position.

ADJUSTMENTS

SKID SHOE ADJUSTMENT:

Level Paved Surface: Adjust skid shoes to obtain 3/16"

to 1/4" clearance between cutting edge and surface.

Uneven or Gravel Surface: Adjust skid shoes to obtain

1/2" to 5/8" clearance between cutting edge and

surface.

LUBRICATION

Apply oil at all pivot points.

Chute Rotation System:

Oil chute base, rotation worm when necessary.

Gear box:

Check the oil annually. If necessary, add AGMA 5 EP or

SAE 90 oil.

The gear box should have a total of 155 ml of oil or filled

to the rim of the bolt hole when installed on the

snowblower.

Rotary driveline: Lubricate the rotary driveline joints

every 8 hours of operation and the splines so that they

slide easily into each other every 16 hours of operation.

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brake.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and

keep away from spark plug(s) to prevent accidental

starting.

CUTTING EDGE MAINTENANCE

Verify from time to time the wearing on the cutting

edge to make sure you do not wear out the base of

the snowblower’s chassis. This cutting edge is

reversible.

SNOWBLOWER PULLEY REPLACEMENT

or ALIGNMENT:

Clean the parts before aligning or replacing the pulley.

Apply some "Loctite" 2760 on the key and the set

screws. Tighten firmly.

MAINTENANCE

BELT REPLACEMENT:

Unscrew the two hex bolts 5/16” x 3/4’’ (item 1) and

remove the driveline guard (item 2).

Remove the driveline (item 3).

Loosen the four flange nuts (item 4) (two on each

side) from the reduction box and the two nylon insert

lock nuts from the tension bar (item 5).

Remove the six flange nuts (item 6).

Remove the reduction plate (item 7).

Replace the belt.

IMPORTANT:

Make sure the notches of the belt are well

inserted into the those of the pulley.

IMPORTANT:

When aligning or replacing the snowblower pulley,

you must clean the parts and use ‘’Locktite’’ 2760 on

the key and the set screws.

Tighten firmly.

Reinstall by reversing the steps .

BELT ADJUSTMENT:

Remove driveline guard (item 2).

Loosen the four flange nuts (item 4) (two on each

side) from the reduction box.

Use the two nylon insert lock nuts on the tension bar

(item 5) to adjust tension.

Loosen the nuts to reduce tension on belt or

tighten the nuts to apply tension.

TIP: There must be between 1/16" and 1/8" of

deflection on one strand of the belt.

Retighten the flange nuts and reinstall the driveline

guard.

DANGER

CONTACT WITH ROTATING DRIVELINE CAN

CAUSE SEVERE INJURY OR DEATH.

Operate only when all driveline, tractor and

equipment shields are in place.

Be sure driveline securely attached and locked at

both ends before operating.

DISMOUNTING & STORAGE

SNOWBLOWER DISMOUNTING

WARNING

TO PREVENT INJURIES:

Stop the motor.

Apply parking brakes.

Remove the ignition key.

Disconnect the wire from the spark plug(s) and keep

away from spark plug(s) to prevent accidental start-

ing.

a) Remove hair pin from handle tube and remove

handle.

b) Disconnect the driveline from tractor’s P.T.O. by

sliding back the collar on the yoke then pull the

driveline out.

c) Detach the snowblower by lifting up the spring

locks on quick hitch and pulling back the

snowblower.

SUBFRAME DISMOUNTING

See the subframe owner's manual for dismounting

instructions.

END OF SEASON STORAGE

a) Clean snowblower and subframe thoroughly and

repaint all parts from which paint has worn.

b) List the replacement parts that will be needed for

the next season.

c) Store the snowblower and the subframe in a dry

place.

d) Follow the instructions in the Lubrication section.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION

Snowblower vibrates or is

abnormally noisy.

Damaged bearing. Replace bearing.

Damaged fan. Dismount & repair or replace fan.

Auger bent. Replace auger.

Auger stopped turning. Shear bolt broken. Replace shear bolt (for identification,

see Parts List "Snowblower Head").

Also see "Maintenance" section.

Fan stopped turning. Shear bolt broken or sheared. Replace bolt (for identification, see

Parts List "Snowblower Head"). The

head of the bolt must be closest to

the snowblower.

Chute rotation is difficult. Dirt or ice may be underneath chute. Clean the base of chute & the

rotation ring. Lubricate chute inside &

out and the rotation worm. Clean

parts, lubricate & reinstall. Make sure

the retaining plates are not too tight

on the chute base, it may be a reason

why the chute is not turning freely.

The base of the chute may be

damaged or bent.

Dismount the chute by removing the

retaining plates. Verify that the base

of the chute is very even and not bent

in a corner, if it is, straighten.

The chute plugs easily. Tractor engine R.P.M. is too slow. Always have tractor engine at full

R.P.M. when using the snowblower.

Advancing too quickly with

snowblower.

Reduce speed. Allows snowblower to

ingest snow at its own speed.

Snowblower digs into ground. Ground is not frozen or too soft. Adjust skid shoes lower so they may

better support the snowblower. If

problem persists, change skid shoes

for "Heavy Duty Skid Shoes" (option

model #700243) which cover more

surface and prevents snowblower

from digging.

Snowblower does not raise

evenly.

Rear tire pressure uneven from one

side to another.

Verify and adjust tire pressure:

Front tires: 14 to 15 p.s.i.

Rear tires: 7 to 8 p.s.i.

Snowblower is not well adjusted. Loosen male hitch on snowblower

(for identification, see Parts

Breakdown "Snowblower Head").

Place a shim (ex.: piece of wood

approx. 2” thick) under the lower side

of snowblower which needs to be

levelled. Re-tighten bolts.

GENERAL TORQUE SPECIFICATION TABLE

USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN

NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal oil. They do not apply if

special graphited or moly disulphide greases or other extreme pressure lubricants are used. This applies to both UNF and UNC

threads.

TORQUE SPECIFICATION TABLE

SEE Grade No. 2 5 8 *

BOLT HEAD

IDENTIFICATION

MARKS AS PER GRADE

NOTE MANUFACTURING

MARKS WILL VARY

TORQUE TORQUE TORQUE

BOLT SIZE POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS POUNDS FEET NEWTON-METERS

Inches Millimetre Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Max. Min. Max. Max.

1/4" 6.35 5 6 6.8 8.13 911 12.2 14.9 12 15 16.3 30.3

5/16" 7.94 10 12 13.6 16.3 17 20.5 23.1 27.8 24 29 32.5 39.3

3/8" 9.53 20 23 27.1 31.2 35 42 47.5 57 45 54 61 73.2

7/16" 11.11 30 35 40.7 47.4 54 64 73.2 86.8 70 84 94.9 113.9

1/2" 12.7 45 52 61 70.5 80 96 108.5 130.2 110 132 149.2 179

9/16" 14.29 65 75 88.1 101.6 110 132 149.2 179 160 192 217 260.4

5/8" 15.88 95 105 128.7 142.3 150 180 203.4 244.1 220 264 298.3 358

3/4" 19.05 150 185 203.3 250.7 270 324 366.1 439.3 380 456 515.3 618.3

7/8" 22.23 160 200 216.8 271 400 480 542.4 650.9 600 720 813.6 976.3

1" 25.4 250 300 338.8 406.5 580 696 786.5 943.8 900 1080 1220.4 1464.5

*Thick nuts must be used with grade 8 bolts

METRIC BOLT TORQUE SPECIFICATIONS

COARSE THREAD

Size Screw Grade No. Pitch (mm) Pounds Feet Newton-Meters Pitch (mm) Pounds Feet Newton-Meters

M6 4T 1.00 3.6 - 5.8 4.9 - 7.9 - - -

7T 5.8 - 9.4 7.9 - 12.7 - -

8T 7.2 - 10 9.8 - 13.6 - -

M8 4T 1.25 7.2 - 14 9.8 - 19 1.00 12 - 17 16.3 - 23

7T 17 - 22 23 - 29.8 19 - 27 25.7 - 36.6

8T 20 - 26 27.1 - 35.2 22 - 31 29.8 - 42

M10 4T 1.50 20 - 25 27.1 - 33.9 1.25 20 - 29 27.1 - 39.3

7T 34 - 40 46.1 - 54.2 35 - 47 47.4 - 63.7

8T 38 - 46 51.5 - 62.3 40 - 52 54.2 - 70.5

M12 4T 1.75 28 - 34 37.9 - 46.1 1.25 31 - 41 42 - 55.6

7T 51 - 59 69.1 - 79.9 56 - 68 75.9 - 92.1

8T 57 - 66 77.2 - 89.4 62 - 75 84 - 101.6

M14 4T 2.00 49 - 56 66.4 - 75.9 1.50 52 - 64 70.5 - 86.7

7T 81 - 93 109.8 - 126 90 - 106 122 - 143.6

8T 96 - 109 130.1 - 147.7 107 - 124 145 - 168

M16 4T 2.00 67 - 77 90.8 - 104.3 1.50 69 - 83 93.5 - 112.5

7T 116 - 130 157.2 - 176.2 120 - 138 162.6 - 187

8T 129 - 145 174.8 - 196.5 140 - 158 189.7 - 214.1

M18 4T 2.00 88 - 100 119.2 - 136 1.50 100 - 117 136 - 158.5

7T 150 - 168 203.3 - 227.6 177 - 199 239.8 - 269.6

8T 175 - 194 237.1 - 262.9 202 - 231 273.7 - 313

M20 4T 2.50 108 - 130 146.3 - 176.2 1.50 132 - 150 178.9 - 203.3

7T 186 - 205 252 - 277.8 206 - 242 279.1 - 327.9

8T 213 - 249 288.6 - 337.4 246 - 289 333.3 - 391.6

FINE THREAD

PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES

CHUTE /GOULOTTE

#700400-1

O/L = Obtain locally/obtenir localement

PARTS LIST / LISTE DES PIÈCES

REF.

RÉF. DESCRIPTION DESCRIPTION QTY

QTÉ

PART #

PIÈCE #

1Chute Goulotte 1103936

2Rotation ring Anneau de rotation 1103943

3Flange nut 1/4" n.c. Écrou à bride 1/4" n.c. 2O/L

4Nylon flat washer 7/16" Rondelle plate de nylon 7/16" 2102011

5Carriage bolt 5/16" n.c. x 3/4" Boulon à carrosserie 5/16" n.c. x 3/4" 2O/L

6Nylon flat washer 11/32" Rondelle plate de nylon 11/32" 2102009

7Knob Bouton 2102020

8Hand guard Fourche protectrice 1102012

9Hex. bolt 1/4" n.c. x 3/4" Boulon hex. 1/4" n.c. x 3/4" 2O/L

10 Flat washer 5/16" hole Rondelle plate 5/16" trou 2O/L

11 Danger decal Décalque danger 1102127

12 Warning decal Décalque attention 1102125

#700400-1

PARTS BREAKDOWN / NOMENCLATURE DES PIÈCES

SNOWBLOWER / SOUFFLEUSE #700400-1

La page charge ...

Bercomac 700416 Manuel utilisateur

Marque: Bercomac

Modèle: 700416

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Ce manuel convient également à

700400-1

Télécharger le PDF

rapport

dans d''autres langues

English: Bercomac 700416 User manual

Bercomac 700416 Manuel utilisateur

Ce manuel convient également à

Bercomac 700416 Manuel utilisateur

dans d''autres langues

Documents connexes