Develco Products H6500115 Guide d'installation

H6500115
Marque
Develco Products
Modèle
H6500115
Catégorie
Extensions de réseau
Taper
Guide d'installation
eng
f.
ALTERNATIVE INSTALLATION OPTION
Another installation option is to replace the
included cable with an alternative cable. If the
installation consists of an in-wall cable, drill
a hole in the marked area, through which the
cable needs to be inserted, and connect the
cable to the Smart Siren. The cable is fastened
with 2 screws (Thread size M3, Length 6mm).
WARNING: This installation should be carried
out by a professional.
Resetting
Resetting is needed if you want to connect your
Smart Siren to another gateway or if you need
to perform a factory reset to avoid abnormal
behavior.
STEPS FOR RESETTING
1. Connect the Smart Siren to a power outlet.
2. Press and hold the menu button the device.
Placement
PLACE THE SIREN
• Indoors at a temperature between 0 and 45°C.
• The siren has to be installed on a wall, where
it is reachable for maintenance. It cannot
hang on the cable.
Precautions
• WARNING: For safety reasons, always make
sure to disconnect the Smart Siren from the
power socket before removing the front
cover.
• Do not remove the product label as it
contains important information.
• Be aware that electronics are sensitive
to static electricity, so aim to discharge
before touching, and avoid touching any
components inside the device.
• Do not paint the device.
• Disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery
can result in an explosion.
• Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
ammable liquid or gas.
• A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of ammable liquid or gas.
• The socket-outlet shall be installed near the
equipment and shall be easily accessible.
Product description
The Smart Siren emits an alarm sound and
sends a notication if intruders, burglars, or
other unwanted guests enter the property.
The Smart Siren includes a voice prompt
and functions as a range extender for Zigbee
networks. The Smart Siren has a battery backup,
so it will still be able to function in case of a
power cut.
Version 2.6
INSTALLATION MANUAL
Smart Siren
a.
b.
c.
d.
e.
Modes
SEARCHING GATEWAY MODE
The yellow LED ashes
MAINS POWERED
The green LED is on
BATTERY BACKUP (MAINS FAILURE)
The green LED ashes. This means that there is
a mains failure, e.g. due to a power outage, and
the device runs on battery for up to 14 hours.
3. While you are holding the button down, the
yellow LED rst ashes once, then two times
in a row, and nally numerous times in a row.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
g.
Fault nding and cleaning
• In case of a bad or wireless weak signal,
change the location of the Smart Siren.
Otherwise, you can relocate your gateway
or strengthen the signal with a range
extender.
• If the search for a gateway has timed out, a
short press on the button will restart it.
Getting started
1. Open the casing of the device by removing
the screw at the bottom of the device
(Thread size M3, Length 8mm).
2. Use the 2 included screws (5x25mm) to
mount the siren on the wall.
4. Insert the screw at the bottom of the device.
3. Attach the front cover to the device by
hooking the front cover to the top of the
mounted device and pushing the front cover
against the device.
5. Insert the plug of the cable attached to the
Smart Siren into a power socket.
6. When the device is powered up, the Smart
Siren will start searching (up to 15 minutes)
for a Zigbee network to join. While the siren
is searching for a Zigbee network to join, the
yellow LED ashes.
7. Make sure that the Zigbee network is open
for joining devices and will accept the siren.
8. When the LED stops ashing, the siren has
successfully joined the Zigbee network.
9. If the scanning has timed out, a short press
on the menu button will restart it.
Disclaimers
CAUTION:
• Shocking hazard! Do not plug into power if
the products have any sign of damage or
exposure of wires.
• Choking hazard! Keep away from children.
Contains small parts.
• Please follow the guidelines thoroughly.
The Smart Siren is a preventive, informing
device, not a guarantee or insurance that
sucient warning or protection will be
provided, or that no property damage,
theft, injury, or any similar situation will
take place. Develco Products´cannot be
held responsible in case any of the above-
mentioned situations occur.
All rights reserved.
Develco Products assumes no responsibility for
any errors, which may appear in this manual.
Furthermore, Develco Products reserves the
right to alter the hardware, software, and/
or specications detailed herein at any time
without notice, and Develco Products does
not make any commitment to update the
information contained herein. All the trademarks
listed herein are owned by their respective
owners.
Distributed by Develco Products A/S
Tangen 6
8200 Aarhus
Denmark
IN ACCORDANCE WITH THE DIRECTIVES
• Radio Equipment Directive (RED)
2014/53/EU
• RoHS Directive 2015/863/EU amending
2011/65/EU
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
which apply to the product and, in particular,
its compliance with the harmonized standards
and specications.
Other certications
Zigbee 3.0 certied
Disposal
Dispose the product properly at the end of its
life. This is electronic waste which should be
recycled.
Disposal of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery,
that can result in an explosion.
FCC statement
Changes or modications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
This device complies with FCC RF radiation
exposure limits set forth for an uncontrolled
environment. The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be co-located or
operating in conjunction with any other antenna
or transmitter.
FCC statement IC statement
ISED statement
Innovation, Science and Economic Develop-
ment Canada ICES-003 Compliance Label:
CAN ICES-3 (B)/NMB-3(B).
ISED statement
Français
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Cet équipement est conforme aux limites
d’exposition aux radiations IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
distance minimale de 20 cm entre le radiateur
et votre corps.
English
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause
undesired operation of the device.
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with minimum
distance 20 cm between the radiator and your
body.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interfer-
ence, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
ISED statement
Conforms to UL 62368-1
Cert. to CAN/CSA Std. C22.2
No. 62368-1-14
UL statement
  • Page 1 1
  • Page 2 2

Develco Products H6500115 Guide d'installation

H6500115
Marque
Develco Products
Modèle
H6500115
Catégorie
Extensions de réseau
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents