Pioneer SC-LX501 Le manuel du propriétaire

Basic

Manual

Hookup

Step1: Choose your Speaker Layout ...................................... 3

Step2: Connect the Speakers ................................................. 9

Step3: Connect the TV ......................................................... 12

Step4: Connect the AV Components .................................... 14

Step5: Multi-zone Connection ............................................... 17

Step6: Connect Other Cables ............................................... 19

Setup

Step7: Power On & Initial Setup ........................................... 20

HDMI Setup .......................................................................... 21

Playback

Basic Playback ..................................................................... 22

Network Functions ................................................................ 23

Others ................................................................................... 25

Part Names

Front Panel ........................................................................... 28

Display .................................................................................. 29

Rear Panel ............................................................................ 30

Remote Controller ................................................................ 31

This manual includes information needed when starting up and also

instructions for frequently used operations. The "Advanced Manual" is

available on the internet with details about the playback features/

listening modes/settings details, specifications, and troubleshooting.

The Advanced Manual is created in a format that makes it easy to read

on a PC or Smartphone.

http://www.pioneer-audiovisual.com/manual/sclx501/adv/en.html

Advanced Manual found here

SC-LX501

> Before start > Hookup > Setup > Playback > Part Names

AV RECEIVER

RECEPTEUR AV

En

Fr

SN29402384_SC-LX501_BAS_En.book 1 ページ２０１６年４月２１日　木曜日　午前１１時４６分

2

> Before start > Hookup > Setup > Playback > Part Names

What's in the box

1. Main unit 2. Remote controller (RC-914R)

×1, Batteries (AAA/R03) ×2

3. Indoor FM antenna ×1 4. AM loop antenna ×1 5. Speaker setup microphone ×1

6. Power cord ×1

Main features

This unit features a Direct Energy HD Amplifier (Class D amplifier) that was developed using the latest digital

amplifier technology. It is capable of simultaneous high-power output and very high quality sound. This amplifier

provides you with the optimum playback of the latest multi-channel digital content.

$ You can connect 7.1ch of speakers to this unit, with 7ch at 180 W (6 ohms, 1 kHz, 0.9%THD) (North American

models) / 180 W (6 ohms, 1 kHz, 1%THD) (European and Asian models) per channel plus pre out jack for

powered subwoofer.

$ Supports playback in Dolby Atmos format which provides 360e sound placement

$ The HDMI jack supports 4K video input and output. Jacks IN1 to 3 and OUT MAIN/SUB support HDCP2.2

$ HDMI CEC functionality: Control features such as linking input switching with the input selector and players

conforming to the CEC standard, switching audio output and volume using the remote controller of a CEC-

compliant TV, and automatically switching this unit to standby when the TV is turned off

$ HDMI Standby Through: Video and audio signals from AV components can be transmitted to the TV even if this

unit is in standby

$ ARC: Connection with an ARC-compatible TV is complete with one HDMI cable

$ Easy Initial Setup using onscreen guidance and On-Screen Display (OSD) showing operations on the TV

$ Internet radio and AirPlay via wired LAN or Wi-Fi (wireless LAN) and network features such as Music Server

that enables PC music file playback, USB playback, plus other playback features such as AM/FM radio and

BLUETOOTH

®

play

$ Playback formats supported by Music Server and USB include WAV, FLAC and DSD high-res source

$ Multi-zone Connection which allows you to play in the main room and listen in a separate room (ZONE 2)

$ You can connect a speaker B system

$ Equipped with RS-232C port, IR IN/OUT jack, and 12V TRIGGER OUT jacks

$ We plan to provide support for the DTS:X audio format through a firmware update for this unit. Refer to our

website for more information.

CAUTION: Connect speakers with 4 Ω to 16 Ω impedance. The power cord must be connected only after

all other cable connections are completed.

0 We will not accept responsibility for damage arising from the connection of equipment manufactured by

other companies.

1

2

56

34

SN29402384_SC-LX501_BAS_En.book 2 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

3

> Before start > Hookup >Setup >Playback >Part Names

Step1: Choose your Speaker Layout

12

Front Speakers

3

Center Speaker

45

Surround Speakers

6

Powered Subwoofer

For 5.1-Channel System

This is a 5.1-channel system that is the basic surround system.

Front speakers output front stereo sound and a center speaker outputs center

sound such as dialogs and vocals. Surround speakers create back sound

field. Powered subwoofer reproduces bass sounds and creates rich sound

field. The front speakers should be positioned at ear height, while the

surround speakers should be positioned just above ear height. Center

speaker should be set up facing the listening position. Place the powered

subwoofer towards the front. Placing it between the center speaker and a front

speaker gives you a natural sound even when playing music.

0 The front speakers, center speaker, and surround speakers are counted as

5 channels, and the powered subwoofer is counted as 0.1 of a channel,

giving us the name 5.1ch system.

Go To "Hookup" (



P9)

1: 22e to 30e, 2: 120e

Speaker B System

In a 5.1-Channel System, you can

connect one more set of front

speakers to use as a Speaker B

System. In this state, the 5.1-

Channel System becomes the

Speaker A System and you can

switch the same audio to output from

A, B, or A+B. Note that sound is not

output from Speaker B when Zone

Speaker is used (



P18).

Go To "Hookup" (



P9)

1

2

SN29402384_SC-LX501_BAS_En.book 3 ページ２０１６年４月２１日　木曜日　午前１１時４６分

4

> Before start > Hookup >Setup >Playback >Part Names

16

(



P3)

78

Surround Back Speakers

For 7.1-Channel System (with

Surround Back Speakers)

This is a system with surround back speakers added to the basic 5.1-channel system.

The connection of surround back speakers improves the sense of envelopment and

connectivity of sound created by the back sound field and provides a more real sound

field. You can select the Dolby Atmos listening mode, which realizes the most up-to-date

3D surround sound, when the input format is Dolby Atmos. With formats other than

Dolby Atmos, you can still create a sound field by outputting sound from the surround

back speakers when you select the Dolby Surround listening mode. The optimal

positioning is for surround back speakers to be at ear height. Place the surround

speakers in a more slightly forward position than you would in a 5.1-channel system.

0 If you are including surround back speakers in the setup, surround

speakers are required.

Go To "Hookup" (



P9)

1: 22e to 30e, 2: 90e to 110e, 3: 135e to 150e

Speaker B System

In a 7.1-Channel System (with Surround

Back Speakers), you can connect one more

set of front speakers to use as a Speaker B

System. In this state, the 7.1-Channel

System becomes the Speaker A System

and you can switch the same audio to

output from A, B, or A+B. Note that sound is

not output from the surround back speaker

when A+B is selected. Note that sound is

not output from Speaker B when Zone

Speaker is used (



P18).

Go To "Hookup" (



P9)

2

3

1

SN29402384_SC-LX501_BAS_En.book 4 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

5

> Before start > Hookup >Setup >Playback >Part Names

3´ (0.9 m)

or more

16

(



P3)

9:

Height Speakers

Choose one of the following:

$

Front High Speakers

Rear High Speakers

For 7.1-Channel System

(with Height Speaker-A)

Front High or Rear High speakers

This is a basic 5.1-channel system with the addition of height speakers, either

as front high speakers or rear high speakers. Select which speakers to setup

according to the environment of the room. You can select the Dolby Atmos

listening mode (5.1.2 channel playback), which realizes the most up-to-date

3D surround sound including overhead sounds, when the input format is Dolby

Atmos. With formats other than Dolby Atmos, you can still create a sound field

by outputting sound from the height speakers when you select the Dolby

Surround listening mode. Front high speakers or rear high speakers should be

situated at least 0.9 m higher than the front speakers. Front high speakers

should be situated directly above the front speakers and the distance between

the rear high speakers should match the distance between the front speakers.

Both should be set up facing the listening position.

Go To "Hookup" (



P10)

1: 22e to 30e, 2: 120e

1

2

SN29402384_SC-LX501_BAS_En.book 5 ページ２０１６年４月２１日　木曜日　午前１１時４６分

6

> Before start > Hookup >Setup >Playback >Part Names

16

(



P3)

9:

Height Speakers

Choose one of the following:

$

Top Front Speakers

Top Middle Speakers

Top Rear Speakers

For 7.1-Channel System

(with Height Speaker-B)

Ceiling speakers

This is a basic 5.1-channel system using ceiling speakers, for example, with

the addition of height speakers, either as top front speakers, top middle

speakers, or top rear speakers. Select which speakers to setup according to

the environment of the room. You can select the Dolby Atmos listening mode

(5.1.2 channel playback), which realizes the most up-to-date 3D surround

sound including overhead sounds, when the input format is Dolby Atmos. With

formats other than Dolby Atmos, you can still create a sound field by

outputting sound from the height speakers when you select the Dolby

Surround listening mode. Fit top front speakers on the ceiling forward of the

seating position, top middle speakers on the ceiling directly above the seating

position, and top rear speakers on the ceiling behind the seating position. The

distance between each pair should match the distance between the two front

speakers.

0 Dolby Laboratories recommends placing this type of height speakers to

obtain the best Dolby Atmos effect.

Go To "Hookup" (



P10)

1: 30e to 55e, 2: 65e to 100e, 3: 125e to 150e

1

2

3

SN29402384_SC-LX501_BAS_En.book 6 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

7

> Before start > Hookup >Setup >Playback >Part Names

16

(



P3)

9:

Height Speakers

Choose one of the following:

$

Dolby Enabled Speakers (Front)

Dolby Enabled Speakers (Surround)

Dolby Enabled Speakers (Surround Back)

For 7.1-Channel System

(with Height Speakers-C)

Dolby enabled speakers

This is a basic 5.1-channel system that using Dolby enabled speakers, with

the addition of height speakers, either as Dolby enabled speakers (front) or

Dolby enabled speakers (surround) or Dolby enabled speakers (surround

back). Select which speakers to setup according to the environment of the

room. Dolby enabled speakers are special speakers designed to face the

ceiling so that sound is heard after bouncing off the ceiling so that sound

appears to be coming from overhead. You can select the Dolby Atmos

listening mode (5.1.2 channel playback), which realizes the most up-to-date

3D surround sound including overhead sounds, when the input format is Dolby

Atmos. With formats other than Dolby Atmos, you can still create a sound field

by outputting sound from the height speakers when you select the Dolby

Surround listening mode. Place them either above the front speakers or above

the surround speakers or surround back speakers.

Go To "Hookup" (



P10)

1: 22e to 30e, 2: 90e to 120e, 3: 135e to 150e

1

2

3

SN29402384_SC-LX501_BAS_En.book 7 ページ２０１６年４月２１日　木曜日　午前１１時４６分

8

> Before start > Hookup >Setup >Playback >Part Names

12

Front Speakers (Bi-Amping)

3

Center Speaker

45

Surround Speakers

6

Powered Subwoofer

For Bi-Amping the Speakers

It is possible to connect front speakers supporting Bi-Amping to improve

quality of the bass and treble. The maximum number of channels available

with this connection is 5.1 because Bi-Amping speakers require one amplifier

for the tweeter jacks and one amplifier for the woofer jacks. The effects and

placements for speakers are the same as the 5.1-channel plan that doesn't

use Bi-Amping speakers.

Go To "Hookup" (



P11)

1: 22e to 30e, 2: 120e

1

2

SN29402384_SC-LX501_BAS_En.book 8 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

9

> Before start > Hookup >Setup >Playback >Part Names

Step2: Connect the Speakers

2

1

Speaker B

3/8˝

(10 mm)

1 Speaker cable, 2 Subwoofer cable

in case of:

Pages 3 to 4

Connect 123456 for a 5.1-channel system. With a

7.1-Channel System (with Surround Back Speakers), also

connect 7 and 8. Up to two powered subwoofers can be

connected. The same signal is output from each of the

SUBWOOFER jacks. With this connection, you can

connect one more set of front speakers to use as a

Speaker B System. Switch Speakers A/B with "Speakers"

in AV Adjust (P26). Note that sound is not output from

the surround back speaker when A+B is selected.

Make sure the exposed wires of the speakers do not stick out of

the speaker terminals when connecting. If the exposed wires of

the speakers touch the rear panel or the + and – wires touch each

other, the protection circuit will be activated.

Setup

0 Settings for the speaker configuration you have

connected need to be made in "1. Full Auto

MCACC" (



P20) in Initial Setup.

SN29402384_SC-LX501_BAS_En.book 9 ページ２０１６年４月２１日　木曜日　午前１１時４６分

10

> Before start > Hookup >Setup >Playback >Part Names

2

1

3/8˝

(10 mm)

1 Speaker cable, 2 Subwoofer cable

in case of:

Pages 5 to 7

Connect 1234569:. Up to two powered

subwoofers can be connected. The same signal is output

from each of the SUBWOOFER jacks.

0 Apart from these connections, you can also connect

surround back speakers 7 and 8. However, you can

only output audio from one set of 78 or 9: at a time.

When you have connected both, you can select which

speakers to prioritize with "Speakers" (



P26) in the AV

Adjust.

Make sure the exposed wires of the speakers do not stick out of

the speaker terminals when connecting. If the exposed wires of

the speakers touch the rear panel or the + and – wires touch each

other, the protection circuit will be activated.

Setup

0 Settings for the speaker configuration you have

connected need to be made in "1. Full Auto

MCACC" (



P20) in Initial Setup. Note that if you

are using height speakers, set "Speaker Channels"

to "5.1.2 ch" in the setting screen. Select "7.1.2 ch"

if you have connected both surround back

speakers and height speakers.

SN29402384_SC-LX501_BAS_En.book 10 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

11

> Before start > Hookup >Setup >Playback >Part Names

1

2

3/8˝

(10 mm)

For high-

frequency

For low-

frequency

1 Speaker cable, 2 Subwoofer cable

in case of:

Page 8

Connect front speakers compatible with Bi-Amping

connection to the FRONT jacks and the SURROUND

BACK jacks. Make sure you remove the jumper bar fitted

between the woofer jacks and tweeter jacks of the front

speakers. In case of Bi-Amping connection, refer to the

instruction manual of your speakers. Up to two powered

subwoofers can be connected. The same signal is output

from each of the SUBWOOFER jacks.

Make sure the exposed wires of the speakers do not stick out of

the speaker terminals when connecting. If the exposed wires of

the speakers touch the rear panel or the + and – wires touch each

other, the protection circuit will be activated.

Setup

0 Bi-Amping connection requires you to change

some settings. Select "Yes" in "Bi-Amp" in "1. Full

Auto MCACC" (



P20) in the Initial Setup.

SN29402384_SC-LX501_BAS_En.book 11 ページ２０１６年４月２１日　木曜日　午前１１時４６分

12

> Before start > Hookup >Setup >Playback >Part Names

Step3: Connect the TV

HDMI IN (ARC)

1

TV

1 HDMI cable

if you have:

ARC TV

This unit is connected between your TV and AV

components. If you connect two or more AV components,

you can select the video displayed on the TV and the

audio output from this unit by changing the input selector.

Shown here are the connections for a TV that supports

the ARC (Audio Return Channel) feature. By connecting

with a single HDMI cable, you can not only output the

video input to this unit to the TV, but you can also play the

sound from the TV through this unit.

Choose an HDMI IN jack on the TV that supports ARC

when connecting.

Another TV or projector can be connected to the HDMI OUT SUB

jack. This jack does not support ARC. For details about how to

output video from the HDMI OUT SUB jack (P22)

Setup

0 Settings are required to use the ARC function.

Select "Yes" in "5. Audio Return Channel" (



P21)

in the Initial Setup.

0 Please refer to the TV's operation manual for

directions on connections and setup for the TV.

SN29402384_SC-LX501_BAS_En.book 12 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

13

> Before start > Hookup >Setup >Playback >Part Names

12

TV

1 HDMI cable, 2 Digital optical cable

if you have:

Non-ARC TV

This unit is connected between your TV and AV

components. If you connect two or more AV components,

you can select the video displayed on the TV and the

audio output from this unit by changing the input selector.

This describes the connections for a TV that does not

support the ARC (Audio Return Channel) feature. By

connecting with both an HDMI cable and a digital optical

cable, you can not only output the video input to this unit

to the TV, but you can also play the sound from the TV

through this unit.

0 Connection with a digital optical cable is not necessary

if you will watch TV through a device such as a cable

set-top box (that is, not use a tuner built into the TV)

that you have connected to the INPUT jack on this unit.

Another TV or projector can be connected to the HDMI OUT SUB

jack. This jack does not support ARC. For details about how to

output video from the HDMI OUT SUB jack (P22)

SN29402384_SC-LX501_BAS_En.book 13 ページ２０１６年４月２１日　木曜日　午前１１時４６分

14

> Before start > Hookup >Setup >Playback >Part Names

Step4: Connect the AV Components

BD/DVD

GAME

1

Cable/Satellite set-top

box

Streaming media

player

1 HDMI cable

if you have:

HDMI AV Components

This is an example of connection with an AV component

that has an HDMI jack. With connection to an AV

component that conforms with the CEC (Consumer

Electronics Control) standard, you can use features such

as the HDMI CEC feature that links with the input selector,

and the HDMI Standby Through feature which allows you

to play video and audio from AV components on the TV

even when this unit is in standby mode.

0 To play 4K or 1080p video, use a high speed HDMI

cable. Further, to enjoy HDCP2.2 compatible video,

connect to the HDMI IN1 to IN3 jacks.

You can connect a device such as a video camera to the AUX

INPUT HDMI jack on the front panel.

Setup

0 HDMI setup (



P21) is required to use the HDMI

CEC and HDMI Standby Through features. Make

settings after all connections are complete.

0 To enjoy digital surround sound including Dolby

Digital, audio output should be set to "Bitstream

output" on the connected Blu-ray Disc player or

other device.

SN29402384_SC-LX501_BAS_En.book 14 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

15

> Before start > Hookup >Setup >Playback >Part Names

OR

1

23

BD/DVD

1 Component video cable, 2 Digital optical cable, 3 Analog audio cable

if you have:

Non-HDMI AV Components

This is an example of connection with an AV component

that does not have an HDMI jack. Make the connections

to the AV component to match the jacks it has. When

video input connection is to the BD/DVD jack, the audio

input connection should also be to the BD/DVD jacks, and

so on, so that you connect the video input jacks to the

jacks with the same name as the audio input jacks. Note

that video signals input to the VIDEO IN jack or the

COMPONENT VIDEO IN jacks will be converted to HDMI

video signals and then output from the HDMI OUT jack.

0 To enjoy digital surround playback in formats such as

Dolby Digital, you need to make a connection for audio

signals with a digital coaxial cable or digital optical

cable.

0 It is possible to change assignment of the input jacks

you see in the illustration at left, so you can also

connect to any jack other than BD/DVD. For details,

see the Advanced Manual.

Setup

0 The COMPONENT VIDEO IN jacks are

compatible only with 480i or 576i resolution. When

you input video signals to the COMPONENT

VIDEO IN jacks, set the output resolution of the

player to 480i or 576i. Select interlace if there is no

option for 480i, etc. If your player does not support

480i or 576i output, use the VIDEO IN jack.

0 To enjoy digital surround sound including Dolby

Digital, audio output should be set to "Bitstream

output" on the connected Blu-ray Disc Player or

other device.

SN29402384_SC-LX501_BAS_En.book 15 ページ２０１６年４月２１日　木曜日　午前１１時４６分

16

> Before start > Hookup >Setup >Playback >Part Names

OR

CD

2

1

Turntable

1 Digital coaxial cable, 2 Analog audio cable

if you have:

Audio Components

Example of a connection with an audio component.

Connect a CD player using a digital coaxial cable or

analog audio cable. You can also connect a turntable that

has an MM-type cartridge to the PHONO jack.

0 If the turntable has a built-in audio equalizer, connect it

to an AUDIO IN jack other than the PHONO jack.

Further, if the turntable uses an MC type cartridge,

install an audio equalizer compatible with the MC type

cartridge between the unit and the turntable, then

connect to any AUDIO IN jack other than the PHONO

jack.

If the turntable has a ground wire, connect it to the SIGNAL GND

terminal of this unit.

SN29402384_SC-LX501_BAS_En.book 16 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

17

> Before start > Hookup >Setup >Playback >Part Names

Step5: Multi-zone Connection

TV

ZONE2

MAIN ROOM

1

1 HDMI cable

if you connect:

ZONE 2 TV

You can enjoy content from a Blu-ray Disc player on a TV

equipped with an HDMI input jack in the separate room

(ZONE 2) by playing a Blu-ray Disc player in the main

room (where this unit is located), or play the content from

another AV component. Only the video from devices

connected to the HDMI IN1 to IN3 jacks can be played on

the TV in the separate room.

Setup

0 Settings are required in Initial Setup, "4. Multi

Zone Setup" (



P21) to enjoy this feature.

0

The audio from externally connected AV

components can only be played in ZONE 2 when the

audio is analog or 2ch PCM audio.

It may also be

necessary to convert the audio output of the AV

component to PCM output.

SN29402384_SC-LX501_BAS_En.book 17 ページ２０１６年４月２１日　木曜日　午前１１時４６分

18

> Before start > Hookup >Setup >Playback >Part Names

ZONE2 PRE/LINE OUT

ZONE SPEAKER

1

2

ZONE2

LINE

IN

MAIN ROOM

1 Analog audio cable, 2 Speaker cable

ZONE 2 PRE/LINE OUT /

ZONE SPEAKER

You can enjoy audio in the separate room by, for example,

playing a Blu-ray Disc player in the main room (where this

unit is located) and listening to internet radio in the

separate room (ZONE 2).

Connections with an AV component

Connect with HDMI IN 1 to 3 if you want to output an

external AV component to ZONE 2. If the AV component

doesn't have an HDMI jack, connect using a digital optical

cable, digital coaxial cable, or analog audio cable.

ZONE 2 PRE/LINE OUT

It is possible to play 2 ch source in a separate room while

7.1 ch source is being played in the main room. Connect

the ZONE 2 PRE/LINE OUT jacks of the unit and the

LINE IN jacks of the pre-main amplifier or the power

amplifier in a separate room with an analog audio cable.

ZONE SPEAKER

It is possible to connect speakers in a separate room and

play 2 ch sources.

0

During ZONE 2 playback, no sound is heard from the surround

back speakers or the height speakers and a maximum of 5.1

channel playback is possible in the main room. Listening modes

such as the Dolby Atmos modes cannot be selected.

0 Note that sound is not output from Speaker B when

Zone Speaker is used.

Setup

0 Settings are required in Initial Setup, "4. Multi

Zone Setup" (



P21) to enjoy this feature.

0

The audio from externally connected AV

components can only be played in ZONE 2 when the

audio is analog or 2ch PCM audio.

If you have

connected to this unit with an HDMI cable or digital

optical/coaxial cable, may be necessary to convert the

audio output of the AV component to PCM output.

SN29402384_SC-LX501_BAS_En.book 18 ページ２０１６年４月２１日　木曜日　午前１１時４６分

En

19

> Before start > Hookup >Setup >Playback >Part Names

Step6: Connect Other Cables

1

3

4

2

(North American

models)

(European and

Asian models)

1 AM loop antenna, 2 Indoor FM antenna, 3 Ethernet cable, 4 Power cord

Antenna Hookup

Move the antenna around while playing the radio to find

the position with the best reception. Use a thumb tack or

similar to attach the indoor FM antenna to a wall.

Network Hookup

Connect this unit to the network using wired LAN or Wi-Fi

(wireless LAN). You can enjoy network features such as

internet radio, Music Server, and AirPlay by connecting

the unit to the network.

If you connect by wired LAN, connect with an Ethernet

cable to the NETWORK port as shown in the illustration.

To connect by Wi-Fi, then after selecting "Wireless" in "3.

Network Connection" (



P21) in Initial Setup, select the

desired setting method and follow the onscreen

instructions to configure the connection.

Power Cord Hookup

This unit includes removable power cords. Connect the

power cord to the power outlet after completing all other

connections. Connect the power cord to AC IN of the unit

and then connect to the outlet. Always disconnect the

outlet side first when disconnecting the power cord.

You can find the voltage selector switch

on the rear panel of multi-voltage

models. Please set it to the correct

voltage for your country or region.

Before changing the voltage, disconnect

the power cord. Use a medium size

screwdriver to change the voltage

switch.

SN29402384_SC-LX501_BAS_En.book 19 ページ２０１６年４月２１日　木曜日　午前１１時４６分

20

> Before start > Hookup >Setup > Playback > Part Names

Step7: Power On & Initial Setup

Initial Setup starts automatically

Once all connections are complete, change the TV's input

to the input for this unit, inset batteries in the remote

controller, and press Í to turn the power on. When you

turn the unit on for the first time, Initial Setup is

automatically shown on the TV to enable you to make

settings required for startup using simple operations

following onscreen guidance.

These instructions will guide you through some items that

you need to check beforehand. Read beforehand so the

setup goes smoothly.

Operation

Select the item with the cursors of the remote controller

and press ENTER (a). To return to the previous screen,

press (b).

To redo the Initial Setup

If you terminate the procedure on the way or want to

change a setting made during Initial Setup, press on

the remote controller, select "System Setup" –

"Miscellaneous" – "Initial Setup" from Home, and press

ENTER.

1. Full Auto MCACC

Place the supplied speaker setup microphone in the

listening position, measure the test tones emitted by the

speakers, then the unit automatically sets the optimum

volume level for each speaker, the crossover frequencies,

and the distance from the listening position. This also

enables correction of distortion caused by the acoustic

environment of the room.

0 When putting the speaker setup microphone on a tripod,

refer to the illustration when putting it in place.

0 The subwoofer sound may not be detected since it is

extremely low frequencies. Set the subwoofer volume to

more than halfway.

0 Calibration takes several minutes to be completed. The

speakers emit the test tone at high volume during

measurement, so be careful of your surroundings. Keep

the room as quiet as possible during measurement. If

the measurement is interrupted, turn off the household

appliances.

a

b

Initial Setup

Language Select

English

Deutsch

Français

Español

Italiano

Nederlands

Svenska

MCACC

SETUP MIC

SN29402384_SC-LX501_BAS_En.book 20 ページ２０１６年４月２１日　木曜日　午前１１時４６分

La page charge ...

Pioneer SC-LX501 Le manuel du propriétaire

Pioneer SC-LX501 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents