Polaris EPIC™ 8640 Le manuel du propriétaire

Robotic Pool Cleaner

Owner's Manual

ENGLISH

|

FRANÇAIS

|

ESPAÑOL

TYPE EN27---

TYPE EN37---

H0699900 Rev A

OWNER'S MANUAL

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this

manual, this product must be serviced by a pool technician who is licensed and qualified in pool equipment

by the jurisdiction in which the product will be installed where such state or local requirements exist. In

the event no such state or local requirement exists, the maintainer must be a professional with sufficient

experience in pool equipment installation and maintenance so that all of the instructions in this manual

can be followed exactly. Improper installation and/or operation may void the warranty.

WARNING

FCC Statement

This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to

the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct

interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

CAUTION

Any changes or modications not expressly approved by the part responsible for compliance could void the user's

authority to operate the equipment.

NOTE: This device complies with FCC and IC RF radiation exposure limits set forth for general population. This device must be

installed to provide a separation distance of at least 20cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada's license-exempt RSS(s) Operation is subject to the following two conditions: (1) This device

may not cause interference. (2) This device must accept any interference including interference that may cause

undesired operation of the device.

THANK YOU FOR PURCHASING THIS ROBOTIC POOL CLEANER.

YOUR ROBOTIC CLEANER HAS BEEN DESIGNED AND MANUFACTURED TO BE EASILY INSTALLED

AND TO PROVIDE LOW MAINTENANCE OPERATION. PRIOR TO INSTALLING YOUR NEW CLEANER,

PLEASE DO THE FOLLOWING:

1) Complete and return the warranty card.

2) Record your purchase information on the spaces provided below.

3) Attach your invoice (or a copy) to this page.

Taking these steps will help ensure prompt warranty service, should it be required. If service is required, please

contact your original dealer. If the original dealer does not perform warranty service, please call our Technical

Support department at 1-800-822-7933.

RECORD YOUR CLEANER DATA HERE:

Date of Purchase Purchased From Serial Number:

(located on robot- head)

City State/Province Zip/Postal Code

2

Robotic Pool Cleaner

|

Owner's Manual

English

Table of Contents

1 Important Safety Instructions ..................... 4

2 Cleaner Specications ................................. 5

Technical Specications ............................................... 5

3 Getting Started ............................................. 6

Contents ....................................................................... 6

Connect to a Power Source.......................................... 6

4 General Cleaner Operation .......................... 7

Install and Submerge the Cleaner ................................ 7

Control Box Buttons...................................................... 8

Start / Stop Cleaning and Select Cleaning Time .......... 8

Removal from Pool ....................................................... 9

5 Maintenance ............................................... 10

Cord Tangling ............................................................. 10

Clean the Filter Canister .............................................. 11

Store the Cleaner When Not in Use ........................... 12

Replacing Wear Parts ................................................. 12

Replacing Brushes ..................................................... 12

6 Installing iAquaLink

®

................................. 14

Download the App ...................................................... 14

Sign Up and Log In ..................................................... 14

Add to Mobile App System ......................................... 14

7 iAquaLink

®

Control* ................................... 15

iAquaLink

®

Control Home Screen ............................... 15

Start / Stop Cleaning and Adjust Cleaning Time......... 15

Set Cleaning Mode ..................................................... 15

Remote Control .......................................................... 15

Removal from Pool ..................................................... 16

In-App Error Messages and Troubleshooting ............. 16

System Settings.......................................................... 16

8 Troubleshooting ......................................... 16

Error Codes ................................................................ 17

General Troubleshooting ............................................ 18

iAquaLink

®

Troubleshooting ........................................ 19

How to Connect .......................................................... 19

Common iAquaLink

®

Troubleshooting ........................ 20

*not available on all models

3

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

1 Important Safety Instructions

Please read through the entire manual before installing your new robotic pool cleaner. The cleaner must

be installed and operated as specied.

WARNING

Failure to comply with the following warnings can result in permanent injury, electrocution or death.

PREVENT ELECTRICAL SHOCK

To reduce risk of electrical shock:

• Connect unit to receptacle protected by a ground fault circuit interrupter (GFCI). Such a GFCI receptacle

should be provided by a qualied installer and should be tested on a routine basis. To test the GFCI, push

the test button. The GFCI should interrupt power. Push the reset button. Power should be restored. If the

GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the pump without

the test button being pushed, a ground current is owing, indicating the possibility of an electric shock.

Do not use this product. Disconnect the cleaner and have the problem corrected by a qualied service

representative before using.

• Per the United States National Electrical Code

®

(NEC

®

), keep the control box at least ve (5) feet from the

edge of the (pool/spa) water. In Canada, the Canadian Electrical Code (CEC) requires a minimum distance

of 3m (10 ft.) to be maintained between the pool edge and the control box. Never submerge the control box.

• Do not enter pool while the cleaner is in water.

• Do not bury cord. Locate cord so as to prevent it from being damaged by lawn mowers, hedge trimmers

and other equipment.

• To reduce the risk of electrical shock, do not use the robotic cleaner or control box if the cord is worn or

damaged. Contact Zodiac Pool Systems LLC. Technical Support immediately for proper servicing and

replacement of the damaged cord.

• Double insulation—For continued protection against possible electric shock, use only identical replacement

parts when servicing. Do not attempt repair of the robotic cleaner, control box, power cord, or oating cable.

• NEVER OPEN CONTROL UNIT.

• DO NOT USE AN EXTENSION CORD TO CONNECT THE UNIT TO ELECTRIC SUPPLY; PROVIDE A

PROPERLY LOCATED GFCI RECEPTACLE. THE CONTROL BOX SHOULD BE PLUGGED INTO THE

GFCI RECEPTACLE BOX.

PREVENT CHILD INJURY AND DROWNING

• To reduce the risk of injury, do not permit children to operate this product.

• Do not let anyone, especially small children, sit, step, lean, or climb on any equipment installed as part of

your pool’s operational system.

4

Robotic Pool Cleaner

|

Owner's Manual

English

SAVE THESE INSTRUCTIONS

The cleaner is a double-insulated product. A

double-insulated electrical appliance is one which

has been designed in such a way that it does not

require a safety connection to ground. The basic

requirement for double-insulation is that no single

failure can result in dangerous voltage becoming

exposed so that it might cause an electric shock

and that this is achieved without relying on an

earthed (grounded) metal casing. This is achieved

by having two (2) layers of insulating material

surrounding live parts or by using reinforced

insulation. Therefore, devices having double-

insulated construction, such as this cleaner, do not

utilize a grounded (three-prong) cord/plug.

CAUTION

Failure to comply with the following warnings could cause damage to pool equipment or personal injury.

• The cleaner must be installed and operated as specied.

• This product is intended for use with permanently-installed pools. Do not use with storable pools. A

permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily

disassembled for storage. A storable pool is constructed so that it is capable of being readily disassembled

for storage and reassembled to its original integrity.

• Clean the lter canister in the cleaner after each use.

• Do not use the product in your pool if the water temperature is above 95˚ F (35˚ C) or below 55˚ F (13˚ C).

USE OF THE ROBOTIC CLEANER IN A VINYL LINER POOL

• Certain vinyl liner patterns are particularly susceptible to rapid surface wear of pattern removal caused by

objects coming into contact with the vinyl surface, including pool brushes, pool toys, oats, fountains, chlorine

dispensers, and automatic pool cleaners. Some vinyl liner patterns can be seriously scratched or abraded

simply by rubbing the surface with a pool brush. Ink from the pattern can also rub off during the installation

process or when it comes into contact with objects in the pool. Zodiac Pool Systems LLC is not responsible

for, and the Limited Warranty does not cover, pattern removal, abrasion or markings on vinyl liners.

2 Cleaner

Technical Specications

The general specications for the cleaner are as

follows:

Control box

supply voltage

100-125 VAC, 60 Hz

Supply voltage

30 V DC

Installed load

150 W max

Specications

5

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

3 Getting Started

Contents

The packaging should contain the following items:

• Robotic cleaner and oating cable

• Control box

• Transport and storage caddy

(not available with all models)

Connect to a Power Source

WARNING

Failure to comply with the following warnings

can result in permanent injury, electrocution or

drowning.

PREVENT ELECTRICAL SHOCK

• U.S.: Per NEC

®

requirements, keep the control

box at least ve (5) ft. (1.5 m) from the edge of the

pool. CANADA: Per CEC

requirements, keep the

control box at least three (3) m (10 ft.) from the

edge of the pool.

• Only connect the control box to a receptacle

protected by a ground fault circuit interrupter

(GFCI). Contact a certied electrician if you cannot

verify that the receptacle is protected by a GFCI.

• Do not use an extension cord to connect the

control box.

• Do not allow anyone to swim while the cleaner is

in the pool.

• The control box is water-resistant, not waterproof.

In order to prevent electrocution, never submerge

the control box or leave exposed to inclement

weather.

1. Firmly insert power cord connector (with

TOP shown facing up) until you hear a

"click" (Figure 1).

NOTE: The "click" indicates the power cord is connected

correctly.

“HAGA CLIC ”

“HAGA CLIC”

Figure 1. Connect Power Cable

NOTE: To disconnect, firmly grip the power cord connector

on each side, press the two tabs, and pull out

(Figure 2).

"CLICK"

Figure 2. Disconnect Power Cable

6

Robotic Pool Cleaner

|

Owner's Manual

English

4 General Cleaner

CAUTION

To prevent damage to the cleaner, to adhere to the

following guidelines:

• Remove the cleaner from the pool after the

cleaning cycle is completed.

• Store out of direct sunlight or inclement weather.

• Never lift the cleaner out of the pool by the

oating cable.

• Take additional care when lifting the cleaner out

of the pool. It becomes heavier when lled with

water.

• Always remove the cleaner from pool when super

chlorinating or adding acid.

• Do not handle cleaner while it is in operation

IMPORTANT

• Always fully submerge the cleaner head before

you begin operation.

• Clean the lter canister after each cleaning

cycle.

• Do not leave your cleaner in the pool on a

permanent basis.

• At the end of each cycle, remove the cleaner

from the pool.

• Start at the cleaner head and untangle any

coils in the cable before storing the cleaner.

The robotic cleaner includes a safety feature that

automatically stops the cleaner if a cleaning cycle

starts but it is not submerged in water. For pools

equipped with a beach area, this safety feature is

programmed to drive the cleaner in reverse and

back into the pool when the impeller is out of the

water.

Install and Submerge the Cleaner

1. With the control box plugged into a power

outlet, spread the oating cable across the

pool deck until you reach the middle of the

pool length.

WARNING: Do not use an extension cord

2. At the center point, submerge the cleaner in

the pool and hold in the vertical position to

release any air trapped inside.

(Figure 3).

1

Figure 3. Submerge the Cleaner Vertically

3. Ensure the unit sinks to the bottom of the

pool and does not oat

(Figure 4).

2

Figure 4. Cleaner Sinking to the Bottom of the

Pool

Operation

7

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

4. Place all of the oating cable in the water

to allow free movement in your pool from

the central point. Spread out the oating

cable ensuring there are no kinks or coils

in the cable (Figure 5).

Figure 5. Pool Entry Point for Optimal Patterning

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Control Box Buttons

The control box can be used to initiate basic

cleaning features and to connect the device to

home Wi-Fi (connected models only).

For more information on connecting your cleaner to Wi-Fi

(connected models),see Section 5, Installing iAquaLink

®

.

Start / Stop Cleaning and Select

Cleaning Mode

The factory default cleaning mode is set to Floor,

Wall, Waterline.

Use to change cleaning surface setting.*

Toggle between modes:

Floor Only (1h 30 min)

Floor, Wall, Waterline (2 hours 30 minutes)

With the cleaner submerged in the water,

press to begin operation.

Press again to interrupt and cancel an in-progress

cleaning cycle.

*not available on all models

Start/Stop cleaning

Select cleaning mode*

Remove cleaner from the pool*

Initiate connection and set up iAquaLink

®

control*

*not available on all models

Button Functions

8

Robotic Pool Cleaner

|

Owner's Manual

English

Removal from Pool

Depending on the model, you can manually

remove the cleaner from the pool or use the Lift

System feature.

For manual removal, pull gently on the oating

cable to bring the cleaner handle within arm's

reach.

Use the handle to lift the cleaner from the water

and hold the cleaner vertically over the pool

surface to drain (Figure 6). Never lift the cleaner

out of the pool by the oating cable.

Using the Lift System*

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be

activated at any time during or after a cleaning

cycle.

1. Press any button to engage cleaner

controls.

2. Press on the control box to begin

the automated procedure to bring the

cleaner to the wall.

NOTE: To stop the procedure at any time, press and

release the button again.

3. Next, Press and HOLD to rotate the

cleaner.

4. Once the cleaner is facing the wall of your

choice for retrieval, release the button.

5. Cleaner will drive forward and up the wall

it is facing. It will wait at the waterline to be

retrieved.

6. When in reach, remove the cleaner from

the pool using the handle. The cleaner

will quickly expel water to allow for lighter,

easier removal (Figure 6).

NOTE: Never lift the cleaner out of the pool by the floating

cable.

*not available on all models

Figure 6. Always remove cleaner using the handle

9

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

5 Maintenance

WARNING

To avoid electric shock and other hazards which

could result in permanent injury or death,

disconnect (unplug) the cleaner from the power

source before performing any cleaning and

maintenance.

Cord Tangling

Tangling can occur more frequently when the

cleaner is not attended to after each cleaning

cycle. Proper installation, general maintenance

and the following troubleshooting steps can help

to avoid cable challenges.

IMPORTANT

Cleaner power cable may become tangled if

correct procedure is not followed after each

cleaning cycle.

NOTE: Place all of the oating cable in the water to allow

free movement in your pool from the central point.

Spread out the oating cable ensuring there are no

kinks or coils in the cable (Figure 7).

caddy /

control unit

cleaner

Recommended

entry point

Not

Recommended

WARNING: Do not use

an extension cord

Figure 7. Optimal Entry Point in Pool

If tangling occurs, follow these steps:

1. Remove the cleaner from the pool. When

the cleaner is within arm's reach, use the

handle to remove from the water. Never lift

the cleaner out of the pool by the oating

cable.

2. Hold the cleaner vertically to drain

(Figure 8).

Figure 8. Keep Cleaner Vertical to Drain Water

3. Unplug power to the cleaner at the control

box (Figure 9).

Figure 9. Unplug

10

Robotic Pool Cleaner

|

Owner's Manual

English

4. Remove the cleaner from the pool and

untangle all kinks and coils in the power

cable. Start at the cleaner head. Lay the

cable in the sun to loosen any tangling

memory (Figure 10).

Figure 10. Untangle the power cable

Clean the Filter Canister

The lter canister should be cleaned at the end of

each cycle.

1. Remove the cleaner from the water and let

the remaining water drain.

2. Unlatch the cleaner cover to access the

canister

(Figure 11).

Figure 11. Lift Cleaner Cover

3. Remove the lter canister from the body

(Figure 12).

Figure 12. Remove Filter Canister

5. Empty all debris from the lter canister,

then rinse the canister and the cleaner

using a hose (Figure 13).

Figure 13. Wash Filter Canister

NOTE: Periodically, deep-clean the filter canister with soapy

water and a soft bristle brush to prevent clogging.

11

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

Store the Cleaner When Not in Use

The cleaner should be cleaned regularly using

slightly soapy water. Do not use solvents such as

trichlorethylene or its equivalent. Rinse the cleaner

generously using clean water. Do not let your

cleaner dry in direct sunlight.

1. Disconnect cleaner from the power source.

2. Starting at the cleaner head, remove all

twists and tangles from the cable. Lay the

cable in the sun to loosen any tangling

memory (see Figure 14).

3. Loosely coil the cable into a loop for

storage near the cleaner or on the caddy

hook (not available with all models).

4. Disconnect the cable from the control box.

Figure 14. Untangle the power cable

Replacing Wear Parts

Replacing Brushes

The cleaner is tted with brushes with a ''wear''

indicator (Figure 15).

raised groove becomes

partially flattened,

indicating excessive

wear

Figure 15. Worn Brush Indicator

To maintain cleaner performance at its best,

replace the brushes as soon as one of the wear

indicators is reached (even if the wear is not

even). It is recommended that you replace the

brushes when the rubber is worn down to the

top of the wear indicator (or every two years,

whichever comes rst).

To replace a worn brush:

1. Stand the cleaner on its end in a vertical

position (see Figure 16).

1

Figure 16. Cleaner in Upright Position

12

Robotic Pool Cleaner

|

Owner's Manual

English

2. Separate the edges of the brush and undo

the tabs. Remove the worn brush (see

Figure 17).

Figure 17. Undo the Tabs of the Brush

3. Position the new brush underneath the

roller with the bristles facing downwards

(see Figure 18).

Figure 18. Position the New Brush on Roller

4. Thread each tab into the slot provided and

gently feed it through until the heel comes

out at the other side of the slot.(Figure 19).

4

Figure 19. Pull Tabs Through Each Slot

5. Use a pair of scissors to cut the tabs 3/4

inch from the heel so that they are no higher

than the cleaning blade (Figure 20).

Figure 20. Cut Tabs

13

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

6 Installing

iAquaLink

®

(connected models only)

The iAquaLink app is available for download from

the App Store or Google Play.

With iAquaLink Control, you can connect to your

robotic cleaner from anywhere, anytime to access

functions and troubleshooting advice. App features

are dependant on model.

Before you begin installation, make sure

you have the following:

• IMPORTANT: Have your Wi-Fi network

password available.

• Robotic Cleaner submerged in the pool.

• Control Box connected and plugged into a

GFCI outlet.

• Smart device (phone or tablet) with Wi-Fi

and Bluetooth enabled

• Wi-Fi router with sufcient signal strength

at the Control Box

Download the App

Install or update the iAquaLink app from the App

Store or Google Play.

Sign Up and Log In

Open the iAquaLink app, then Sign Up or Log In.

Complete all required elds in the Account Set Up

page and agree to the Terms and Conditions.

Add to Mobile App System

1. On the My Systems page, click + in the

upper right-hand corner to add a system.

2. Choose "Robotic Cleaner". Follow in

app instructions to add your cleaner and

connect it to your home router.

3. On the control box, press

Bluetooth light

indicates status:

BLINKING - searching for signal

SOLID - paired with phone

Wi-Fi light indicates status:

BLINKING - connected to router

SOLID - connected to the internet

NOTE: Errors during connection may be the results of

insufficient Wi-Fi signal strength at the control box

location. If you are unable to move the control or

router to improve signal strength, you may need a

Wi-Fi extender to boost your signal strength. (See

iAquaLink Troubleshooting section.)

An incorrect password may also be that cause of a

connection error. If the signal strength at the control

box is good, double check the network name and

credentials for the router you are trying to access.

14

Robotic Pool Cleaner

|

Owner's Manual

English

7 iAquaLink

®

Control

(connected models only)

Once you have downloaded the iAquaLink app and

connected the device to Wi-Fi, the iAquaLink app

allows for robotic cleaner control from anywhere,

anytime. Functions vary within the iAqualink app

depending on which cleaner model you have.

WARNING

Do not enter pool while the robotic cleaner

is in water.

iAquaLink

®

Control Home Screen

App function and design is subject to change.

Start/Stop Cleaning

Remote*

Clean Mode

Lift System*

*not available on all models

Start / Stop Cleaning

The factory default cleaning surface setting is

Floor, Wall, Waterline.

1. From the Home screen or the Control Box

press the Start/Stop button to begin

cleaning.

2. The app displays the cycle time in hours

and minutes.

3. Press to interrupt and cancel an in-

progress cleaning cycle.

Set Cleaning Mode

1. From the home screen, select Cleaning

Mode to view and select.

Remote Control*

Use your mobile device as a remote control.

IMPORTANT: Only use Remote Control when in view of the

cleaner.

1. From the main screen, select the Remote

tab.

2. You can direct the cleaner using the remote

control to help pick up debris.

NOTE: If you experience significant delays between the

app command and cleaner response, you may

have a weak Wi-Fi signal or other connectivity

challenges that interfere with the immediacy of

the remote control functions.

*not available on all models

15

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

Removal from Pool

Depending on the model, you can manually

remove the cleaner from the pool or use the Lift

System* feature in app or on the control box.

The Lift System is designed to assist in retrieving

the robot from the pool. Lift System can be

activated at any time during or after a cleaning

cycle.

IMPORTANT: Only use Lift System when in view of the

cleaner.

1. From the home screen, select Lift

System to enter automated procedure.

2. Use the left and right controls to rotate the

cleaner to face the wall of your choice.

3. Press the Start Button to drive the cleaner

up the wall it is facing. The cleaner will wait

at the water line to be retrieved.

NOTE: To stop the procedure at any time, press and release

the button again.

4. When in reach, grab the cleaner handle

and begin to pull cleaner out of the water.

The cleaner will quickly expel water to

allow for lighter, easier removal.

NOTE: Never lift the cleaner out of the pool by

the floating cable.

*not available on all models

In-App Error Messages and

Troubleshooting

If an error occurs, cleaning will be interrupted and

the app will display an error message.

The message will display:

• The error code and name

• A brief description of the error

• A set of troubleshooting steps you can take to

resolve the error (if available for the error type)

Tap "Clear Error" when you believe you have xed

the problem and want to try again or anytime you

want to return to the home screen.

System Settings

Access System Settings by pressing the gear icon

in the upper right hand corner of the app screen.

16

Robotic Pool Cleaner

|

Owner's Manual

English

8 Troubleshooting

• If the status indicator on the control box ashes to alert the user, follow the recommended

troubleshooting tips below

• User alerts can also be accessed in the iAquaLink

®

app (on connected models only)

Error Codes

Flashing LED

In-App Display

(depending on the model)

Solutions

Rapid flashing

1 ash / 1 second pause

Communication

• Disconnect and reconnect the cleaner.

• Check that the cable is properly connected to the control box.

• Check that nothing is interfering with the cable connecon

area.

• If this does not resolve the problem, contact your local retailer

for a diagnosc review or call customer service.

Rapid flashing

2 ash / 1 second pause

Right traction motor

Left traction motor

Right traction motor

consumption

Left traction motor

consumption

• Check that debris or the cable is not prevenng the brushes or

the tracks from rotang freely.

• Check that nothing is interfering with the cable connecon

area.

• Rotate the track by a quarter of a turn in the same direcon

unl it rotates smoothly

• If this does not resolve the problem, contact your local retailer

for a diagnosc review or call customer service.

Rapid flashing

3 ash / 1 second pause

Cleaner out of the water

• Turn the cleaner o.

• Clean the lter thoroughly.

• Put it back in the water, shaking to release the air bubbles.

• Restart the cycle.

• If this does not resolve the problem, contact your local retailer

for a diagnosc review or call customer service.

Pump motor

Pump motor consumption

• Check that no debris or hair is blocking the impeller.

• Clean the lter thoroughly.

• If this does not resolve the problem, contact your local retailer

for a diagnosc review or call customer service.

iAquaLink Control Models Only

Rapid flashing

5 ash / 1 second pause

Software update failed or

incomplete

• Disconnect and reconnect the control box to restart the

update.

• If this does not resolve the problem, contact your local retailer

for a diagnosc review or call customer service.

Rapid flashing

Update in progress

• Wait for the update to complete.

• Do not disconnect the power cable from the cleaner during

an update.

N/A Connection error

• Check the status of the Bluetooth/Wi-Fi LEDs on the control

box.

N/A

A red dot appears in the "My

systems" list

• Robot not plugged in or not connected to the home Wi-Fi

network.

If the dot is red when the control box is plugged in and if

the Bluetooth/Wi-Fi icons are lit up, refresh the screen (by

swiping downwards).

• If the dot turns green: the robot is ready for use.

Deleng an error code

Using the control box:

• Aer following the troubleshoong soluons, press any key to delete the error code (except the buon).

From the iAquaLink

®

app (connected models only):

• Aer following the troubleshoong soluons, press Clear Error.

17

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

General Troubleshooting

The following list provides some helpful hints for troubleshooting common challenges when using the cleaner.

User Issue Possible Cause Suggested Solution

The cleaner does not stay

on the pool surface or is

oating excessively.

There is air trapped inside the

cleaner housing.

Remove cleaner from pool and re-submerge

(see Install and Submerge the Cleaner).

The lter canister is full or dirty. Dispose of debris and thoroughly clean the lter

canister with mild soap and a soft brush. Then,

re-submerge the cleaner (see Clean the Filter

Canister).

The cleaner is not climbing

walls.

The lter canister is full or dirty. Dispose of debris and thoroughly clean the lter

canister with mild soap and a soft brush. Then,

re-submerge the cleaner (see Clean the Filter

Canister).

Conrm appropriate pool chemistry Speak with your pool service professional.

Do not leave cleaner in the pool during any

chemical treatments.

The cleaner is not moving Not connected to electricity. The outlet the control box is connected to, is

not supplying electrical power. Check that the

outlet to which the control box is connected is

receiving electricity.

Cycle not started. Press the Start button to initiate a cleaning

cycle.

Reset needed Disconnect the unit power and reconnect after

20 seconds. If the problem is not resolved,

contact your local retailer to request a

diagnostic review or contact Technical Support

at 1-800-822-7933.

Cable is tangling in the pool. Cable is not spread evenly in the

water

Verify the oating cable enters the water near

the middle of the pool length. Spread all of the

oating cable carefully in the pool, ensuring

there are no kinks or coils. Ensure the cable is

not too tightly wrapped or coiled when storing.

If the problem persists, lay the cable straight in

the sun to relax it and remove kinks. Follow the

procedure in Cord Tangling to avoid and correct

tangled cord.

The cleaner is not cleaning

the pool effectively.

Filter canister is full or dirty. Dispose of debris and thoroughly clean the lter

canister with mild soap and a soft brush. Then,

re-submerge the cleaner (see: Clean the Filter

Canister).

Brushes are worn. Check the wear indicator(s). Contact your local

dealer for spare parts.

Cable is excessively tangled. Untangle the twisted cord and lay in sun to

reduce memory. (See: Cord Tangling).

18

Robotic Pool Cleaner

|

Owner's Manual

English

iAquaLink

®

Troubleshooting (not available on all models)

This information can help to troubleshoot connection and setup challenges between the iAquaLink app

and the cleaner.

How It Works

Your

Smart

Device

Your

Internet

Router

Cleaner

Control

Unit

Robotic

Pool

Cleaner

Internet

How to connect:

You must connect to the home router (network) by rst establishing a direct connection between the

control box and your smart device. (See: Conguring the System.)

IMPORTANT: It is recommended to locate the control box as close to the home router as practical. Do

not use an extension cord.

19

Robotic Pool Cleaner

|

Owner's Manual Robotic Pool Cleaner

|

Owner's Manual

English

Zodiac Pool Systems Canada, Inc.

2-3365 Mainway

Burlington, ON • Canada L7M 1A6

1.888.647.4004 | www.ZodiacPoolSystems.ca

Common iAquaLink

®

Troubleshooting

Remember, if you get a new Wi-Fi Router, reset the defaults of your current Wi-Fi Router or simply change

your Wi-Fi network password, you will have to re-establish the connection between your cleaner and the

router. (See: Congure the System.)

User Issue Possible Cause Suggested Solution

All lights are off Bright sunlight Shield the lights to block sunlight and re-check if

the lights are lit.

Control box is unplugged. Plug the control box in. (See: Connect to a Power

Source).

Power outage. Verify that the breaker is on and electricity is

being supplied to the outlet.

Lost internet connection. Check internet connection - Network may be

down.

Wi-Fi is off Router is off. Turn router on.

Router password was changed. Reset router with new password.

Wi-Fi light is ashing Lost internet connection Check internet connection - Network may be

down.

Control box is too far from home

router

Relocate the control box as near to the home

router as practical. (See: Install and Submerge

the Cleaner) Do not use an extension cord.

Weak Wi-Fi signal • Check for adequate Wi-Fi signal strength.

• With a Windows laptop, go to Network

Connections in the Control Panel. Check

Signal Strength meter under Wireless

Network Connection icon while standing near

the control box.

• With a smart device, search for, download,

and use an app that can check signal

strength while standing near the control box.

If Wi-Fi signal is weak, consider installing a

Wi-Fi extender.

Connectivity issue with local Wi-Fi or

connection to the server

Contact your local internet service provider.

• Unplug your control box and wait 10

seconds. Plug in the box again and see if

lights illuminate.

• Check Internet connection - Network may be

down.

Status light is continuously

ashing

Antenna rmware update in progress. Wait for the update to complete and the ashing

to end. Do not disconnect the power cable from

the cleaner during an update.

Power LED is blinking fast Firmware update in progress Wait for blinking to stop, indicating update is

complete. Do not unplug from power during an

update.

Robotic Pool Cleaner

|

Owner's Manual

20

Zodiac Pool Systems LLC

2882 Whiptail Loop # 100, Carlsbad, CA 92010

1.800.822.7933 | www.PolarisPool.com

H0699900 REV A

All trademarks are property of their respective owners.

Apple and the Apple logo are trademarks of Apple, Inc., registered in the U.S. and other countries. App Store is a service mark of

Apple, Inc., registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google LLC.

La page charge ...

Polaris EPIC™ 8640 Le manuel du propriétaire

Ce manuel convient également à

Polaris EPIC™ 8640 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents