Matrox Millennium G550 Manuel utilisateur

Catégorie
Cartes graphiques
Taper
Manuel utilisateur
Millennium
G
550
User Guide
10776-301-0100
2001.07.30
ENGLISH
2 Matrox Graphics Card – User Guide
Hardware installation
This section describes how to install your Matrox card. If your Matrox graphics card is already
installed in your computer, skip to Connection setup, page 4. For information specific to your
computer, like how to remove its cover, see your system manual.
1
Switch to the standard VGA display driver
If you’re running Windows 98/Me/2000 on your computer, this step isn’t necessary.
If you’re using another operating system (for example, Windows NT 4.0), see its
documentation for how to switch to VGA mode.
2
Open your computer and
remove your existing graphics
card
*
Turn off your computer and all peripherals
such as your monitor or printer. Open the
computer and remove your existing
graphics card (if any). (If graphics hardware
is built into the motherboard of your
computer, this graphics hardware should
automatically disable itself after your
Matrox card is installed.)
WARN I N G:
To avoid personal injury, turn off your computer, unplug it, and then wait for
it to cool before you touch any of its internal parts. Also, static electricity can severely damage
electronic parts. Before touching any electronic parts, drain static electricity from your body
(for example, by touching the metal frame of your computer). When handling a card,
carefully hold it by its edges and avoid touching its circuitry.
* With multi-display mode, you may be able to use your existing graphics card. For Windows 98/Me/2000, see Windows
98/Me/2000 online help under “Multiple Display Support”. For Windows NT 4.0, only Matrox graphics card models supported
by the Matrox display driver can be used.
Matrox Graphics Card User Guide 3
3
Choose an expansion slot
Most computers have different types of
expansion slots. Choose an AGP or PCI slot,
depending on the type of Matrox card you
have. Your system manual should identify
the location of each type of expansion slot in
your computer.
4
Insert your Matrox card
a
Remove the cover for the slot you intend
to use.
b
Save the screw for the mounting
bracket. Position your Matrox card over
the expansion slot youve chosen.
c
Push the card in firmly and evenly until
its fully seated in the slot.
d
Replace the screw to secure the bracket
of your Matrox card to the computer
frame.
Your Matrox card is now installed.
Before restarting your computer
, connect your monitor or
monitors (see Connection setup, page 4).
After connecting
, restart your computer and install your
Matrox software (see Software installation, page 8).
WARN I N G:
Inserting your Matrox card
into the wrong type of slot could damage
your card, your computer, or both.
If you have an AGP card,
don’t
insert the
plastic tab (see picture) into the slot.
AGP slot
PCI slot
ISA slot
(Back of computer)
AGP cardPCI card
Plastic
tab
4 Matrox Graphics Card User Guide
Connection setup
For the purpose of determining your connection setup, there are 3 types of graphics cards:
!
DVI/HD-15
a DVI (white) and an HD-15
(blue) connector
!
DVI only
only a DVI (white) connector
!
LFH-60 –
only an LFH-60 (black) connector
WA R NI N G:
Dont change monitor connections while your computer is turned on. While
your computer is turned on, it may be using monitor settings that are specific to the current
monitor connections.
Some
devices may be permanently damaged if incorrect settings are
used.
Note:
To c o n n e c t a
digital
monitor (a
monitor that uses digital input, usually a flat
panel monitor) to your Matrox product,
your monitor must have a DVI connector.
P&D and MDR-20 connectors arent
supported.
If you have an
analog
monitor (a monitor
that uses analog input) with a DVI
connector and you want to connect it to an
HD-15 connector, youll need a separate
adapter. If this adapter isnt included with
your monitor, contact your monitor vendor.
Some monitors with DVI connectors support both digital and analog input. If youre using
one of these monitors with your Matrox product, make sure its configured to use the correct
type of input. For more information, see your monitor documentation.
DVI HD-15
DVI
LFH-60
HD-15 connector (analog)
P&D connector
(digital)
MDR-20 connector
(digital)
DVI connector
(digital)
DVI connector
(analog/digital)
Matrox Graphics Card User Guide 5
If you have a DVI/HD-15 graphics card
If your Matrox card has a DVI and an HD-15
connector, you can connect up to two
monitors directly to your card.
You can use the HD-15 connector on your
card to connect an analog monitor.
You can use the DVI connector on your card
to connect a digital monitor.
You can also use the DVI connector to
connect an analog monitor. You should do
this only when theres already a device
connected to the HD-15 connector. You can
connect an analog monitor with a DVI
connector directly. You can also connect an
analog monitor with an HD-15 connector
using a DVI-to-HD15 adapter. If you need
this adapter and its not included with your
Matrox product, contact your computer
vendor.
If you have a DVI-only graphics card
If your Matrox card only has a DVI
connector, you can connect one monitor
directly to your card or up to two monitors
using a dual-monitor cable.
You can connect a monitor with a DVI
connector directly to your card.
You can also connect an analog monitor
with an HD-15 connector using an analog
dual-monitor cable (included with certain
Matrox products) or using a DVI-to-HD15
adapter. If you need this adapter and its not
included with your Matrox product, contact
your computer vendor.
HD-15
connector
DVI
connector
DVI connector
HD-15 connector
DVI-to-HD15 adapter
HD-15 connector
DVI
connector
DVI connector
DVI
connector
DVI-to-HD15 adapter
HD-15 connector
DVI
connector
6 Matrox Graphics Card User Guide
To use a dual-monitor cable to connect one
or two analog monitors, connect it to your
card and to your analog monitor cables. If
youre connecting only one monitor, use the
main connector (labeled
1
or
1/3
) of your
dual-monitor cable.
If you have an LFH-60 graphics card
If your Matrox card only has an LFH-60
connector, you can connect up to two
monitors to your card using a dual-monitor
cable. The type of monitor you can connect
to your card depends on the type of dual-
monitor cable you have.
If youre using an
analog
dual-monitor cable
(a cable with HD-15 connectors), connect it
to your card and to your analog monitor
cables. If youre connecting only one
monitor, use the main connector (labeled
1
or
1/3
) of your dual-monitor cable.
If youre using a
digital
dual-monitor cable
*
(a cable with DVI connectors), connect it to
your card and directly to your digital
monitors. The dual-monitor cable replaces
the cables that came with your digital
monitors. If youre connecting only one
monitor, use the main connector (labeled
1
or
1/3
) of your dual-monitor cable.
* The digital dual-monitor cable is only available for cards with an LFH-60 connector.
HD-15
connector (1)
HD-15
connector (2)
Dual-monitor
cable
LFH-60 connector
HD-15
connector (1)
HD-15
connector (2)
A
na
l
og
d
ua
l
-
monitor cable
Digital monitor
DVI connector
Digital dual-
monitor cable
Matrox Graphics Card User Guide 7
Determining your main and secondary display
Your Matrox hardware has a main display and a secondary
display the main display is more capable than the
secondary display. Which connector the software uses for
your main display depends on your connection setup.
!
If your Matrox card has a DVI and an HD-15 connector,
there are 3 conditions that
determine which connector is used for your main display:
"
If a digital monitor is connected, the DVI connector is used for your main display.
"
If the TV output adapter is connected, the DVI connector is used for your main
display.
"
If no digital monitor or no TV output adapter is connected, the HD-15 connector is
used for your main display.
!
If your Matrox card only has a DVI connector and youre not using a dual-monitor
cable,
this connector is used for your main display.
!
If youre connecting your monitors using a dual-monitor cable,
the connectors are
numbered. The main display uses the connector labeled
1
(or
1/3
) and the secondary
display uses the connector labeled
2
(or
2/4
).
Note:
To connect to the digital dual-monitor cable, your monitor must have a DVI
connector. P&D and MDR-20 connectors (see page 4), and analog monitors arent supported
with this cable.
Note:
Whenever you change your connection setup, make sure youre using the correct
connectors and that all connectors are properly fastened.
Whenever you restart your computer, make sure your monitors are already turned on.
Otherwise, the software may not be able to properly detect your monitors.
Note:
If a TV output adapter is included with your Matrox
product, you can use this adapter to connect a TV or video
recorder to your Matrox product. The adapter connects to the
HD-15 connector on your card or to the connector labeled
2
(or
2/4
) on an analog dual-monitor cable. For more information, see
TV output in the online version of this guide.
VIDEO OUT
S-VIDEO OUT
TV output adapter
8 Matrox Graphics Card User Guide
Software installation
This section describes how to install Matrox software for
Wi ndows
*
98/Me/2000 or NT 4.0
. (For other operating systems,
see the
Readme
file in the root folder of the Matrox installation
CD-ROM.)
Windows 2000 or NT 4.0
You may need administrator rights
to install certain software. For more information, see Windows
documentation.
1
Restart your computer
If youre using Windows 98/Me/2000
, it detects new
hardware when you restart. If Matrox display drivers havent been previously installed,
Windows reports finding a PCI adapter (even if you have an AGP card). Windows prompts
you to install a display driver. Follow the on-screen instructions. (The Matrox Windows
98/Me display driver is in the
Win9x
folder of your Matrox installation CD-ROM. The
Matrox Windows 2000 display driver is in the
Win2k
folder.)
2
Install required software
After your computer has restarted, insert (or reinsert)
the Matrox installation CD-ROM in your CD-ROM drive the setup program automatically
starts.
This setup program works with Windows 98/Me/2000
and NT 4.0, and detects which
operating system youre using. If the required display software isnt already installed, the
setup program automatically prompts you to install this software. Follow the on-screen
instructions.
After the required display software is installed, youre prompted to restart your computer for
changes to take effect. Leave your Matrox CD-ROM in your CD-ROM drive.
3
Install optional software
After your computer restarts, the setup program shows
you a list of additional items you can install. For each item you want to install, select a list
item, click
Install
, then follow the on-screen instructions.
4
Set up your display software
See Display setup, page 9.
* Unless otherwise indicated, references to
Windows 2000
also apply to
Windows XP.
2
k2k
NT
2
k
NT
9
898
9
8
2k2k
M
eMe
Me
If Windows doesnt automatically start the setup program, you can start it manually from the root folder of the CD-ROM.
Note:
Included with certain Matrox products is software for HeadCasting. With
HeadCasting
, you can use real-time 3D animated heads in programs that support this feature.
For more information, see Matrox HeadCasting in the online version of this guide.
Matrox Graphics Card User Guide 9
Display setup
Your Matrox display driver includes Matrox PowerDesk software. This software helps you get the
most out of your Matrox graphics card. This section has important information on how to configure
your display settings using Matrox PowerDesk software.
Accessing PowerDesk property sheets
Many display controls are on Matrox PowerDesk property sheets. You can identify
Matrox PowerDesk property sheets by the icon appearing on the tab. To access
these property sheets:
!
Windows 98/Me/2000
Right-click your Windows desktop background, then click
Properties
#
Settings
#
Advanced
. If youre using a multi-display desktop, select a
display before clicking
Advanced
.
!
Windows NT 4.0
Click
#
Settings
#
Control Panel
#
Matrox Display
Properties
(double-click).
Also, to quickly access PowerDesk features, click the Matrox QuickDesk icon ( ) on your Windows
taskbar.
Monitor setup
Before changing your display resolution, color palette, or other Matrox PowerDesk settings, make
sure correct software monitor settings are selected. If you have a Plug-and-Play (DDC) monitor, the
correct settings are usually automatically selected. The following explains how to make sure your
monitor settings are okay.
9
898
9
8
2k2k
M
eMe
Me
NTNT
Note:
Multi-display mode is supported under Windows 98/Me/2000 and NT 4.0. For more
information on multi-display mode, see Windows 98/Me/2000 online help under Multiple
Display support and see DualHead Multi-Display setup, page 10.
WA R NI N G:
If incorrect software monitor settings are applied,
some
monitors can be
permanently damaged. For more information, see your monitor manual.
10 Matrox Graphics Card User Guide
Windows 98/Me/2000
If you have a Plug-and-Play (DDC) monitor, Windows should
automatically use the correct settings for your monitor. To make sure the correct monitor is
selected in Windows:
1
Right-click your Windows desktop background, then click
Properties
#
Settings
.
2
Depending on what version of Windows you have, click
Change Display Type
, or
Advanced Properties
#
Monitor
, or
Advanced
#
Monitor
. If youre using a multi-display
desktop, select a display before clicking
Advanced
.
3
If the monitor name listed doesnt match your monitor, click the
Change
button to select
a new monitor name. Follow the on-screen instructions.
For more information on Windows monitor settings, see Windows documentation.
If you want to customize your Windows monitor settings:
1
Access the PowerDesk
Monitor Settings
property sheet (see Accessing PowerDesk
property sheets, page 9).
2
Depending on what you want to do, click one of the buttons in the
Monitor settings
selection method
box, then follow the on-screen instructions.
Windows NT 4.0
1
Access the Matrox PowerDesk
Monitor
property sheet (see Accessing PowerDesk
property sheets, page 9).
2
If you have a Plug-and-Play monitor:
Make sure the
Plug-and-Play (DDC) monitor
button is
selected. If so, the Matrox display driver
automatically
uses the correct settings for your
monitor. If not, click this button, then click
Apply
.
If you dont have a Plug-and-Play monitor:
See if the
Default monitor (60 Hz)
button is selected. If
so, use the Matrox monitor selection method. For more information on Matrox monitor
selection, see Matrox PowerDesk online documentation.
DualHead Multi-Display setup
With your Matrox graphics card, you can enable a second display (for example, a computer monitor
or a TV) as part of your Windows desktop. This is the Matrox
DualHead Multi-Display
feature. To use
this feature:
Windows 98/Me/2000
When you first restart your computer, youll be prompted to enable
the DualHead Multi-Display feature. Follow the on-screen instructions. For more
information, see the online help.
9
898
9
8
2k2k
M
eMe
Me
NTNT
9
898
9
8
2k2k
M
eMe
Me
Matrox Graphics Card User Guide 11
Windows NT 4.0
1
Access the Matrox PowerDesk
DualHead
property sheet (see Accessing PowerDesk
property sheets, page 9).
2
Select the
DualHead Multi-Display
option button.
3
Click
OK
#
Yes
to restart your computer and for changes to take effect.
4
Access the Matrox PowerDesk
Settings
property sheet (see Accessing PowerDesk
property sheets, page 9).
5
Click
Multi-Display Desktop
( ).
6
Move the
Desktop area
slider to adjust your multi-display desktop, then click
OK
to
accept your changes.
Other DualHead features
If your Matrox graphics card has a second monitor connector you can also use these features:
Windows 98/Me/2000 or NT 4.0
!
DualHead Clone
View a copy of your main display on your secondary display. Each
display can use different monitor settings (refresh rates).
!
DualHead Zoom
Use your secondary display to view a zoomed-in portion of your main
display.
Windows 98/Me/2000
!
DualHead DVDMax
Play digital video in a window on your main display and, at the
same time, view that video full-screen on your secondary display.
Note:
In multi-display mode under Windows NT 4.0, the same display resolution and color
palette is used for each display.
Note:
You can also use your main and secondary displays for two distinct views in games that
use the DualHead Multi-Display feature. For more information on games that use this
feature, see the Matrox Web site (www.matrox.com/mga
).
NTNT
12 Matrox Graphics Card User Guide
More PowerDesk information
For more information on Matrox PowerDesk:
Windows 98/Me/2000 or NT 4.0
!
For context-sensitive help where available, click the icon in the title bar, then click
the item you want help on. Right-click a help topic for a pop-up menu that lets you print
or copy it. (Some help topics are only available through context-sensitive help.)
Windows 98/Me/2000
!
Access the PowerDesk
Information
property sheet (see Accessing PowerDesk property
sheets, page 9), then click
Help
or
View Readme File
.
Windows NT 4.0
!
Access the Matrox PowerDesk
Information
property sheet (see Accessing PowerDesk
property sheets, page 9).
!
Click the Matrox QuickDesk icon ( ) on your Windows taskbar, then click
Help
#
PowerDesk Guide
or
Help
#
View Readme File
.
9
898
9
8
2k2k
M
eMe
Me
NTNT
Matrox Graphics Card User Guide 13
Troubleshooting
Basic procedures
This section explains basic procedures that are referred to by some troubleshooting items in this
guide.
Restarting in safe mode
What follows is information on how to restart your computer in
safe mode
(or
VGA mode
).
If your primary display is
usable
:
Windows 98/Me/2000 or NT 4.0
1
Restart your computer:
"
Windows 98/Me/2000
Click
#
Shut Down
#
Restart
#
OK
.
"
Windows NT 4.0
Click
#
Shut Down
#
Restart your computer
#
Yes
.
2
Windows 98/Me/2000
Before
Windows starts, press [F8] for the Windows startup
menu to appear. (If [F8] doesnt work, instead try pressing and holding [Ctrl] before
Windows starts.)
3
Select safe mode or VGA mode, then press [Enter].
If your primary display is
unusable
:
Windows 98/Me
1
Press [Ctrl]+[Alt]+[Del] twice to restart your computer.
2
Before
Windows starts, press [F8] for the Windows startup menu to appear. (If [F8]
doesnt work, instead try pressing and holding [Ctrl] before Windows starts.)
3
Select safe mode, then press [Enter].
Windows 2000
1
Press [Ctrl]+[Alt]+[Del]
#
[Tab]
#
[Tab]
#
[Enter]
#
[
$
] (down arrow)
#
[Enter] to
restart your computer.
2
Before
Windows starts, press [F8] for the Windows startup menu to appear.
3
Select safe mode, then press [Enter].
9
898
9
8
M
eMe
Me
2k2k
14 Matrox Graphics Card User Guide
Windows NT 4.0
1
Press [Ctrl]+[Alt]+[Del]
#
[Tab]
#
[Tab]
#
[Enter]
#
[
$
] (down arrow)
#
[Enter] to
restart your computer.
2
From the startup menu, choose Windows VGA mode.
Main troubleshooting
This section addresses possible problems that could prevent you from using your computer.
Problem Computer doesn’t display information or boot after Matrox card is installed
1
Cause
Your Matrox card may not be properly installed.
1
Solution
Make sure your Matrox card is properly installed. Specifically, make sure the card is firmly
inserted in its expansion slot and that all connections to it are firmly in place. For more
information, see Hardware installation, page 2.
2
Cause
There may be an unsupported graphics adapter in your computer. (For Matrox
multi-display
mode
in Windows NT, all graphics cards in your computer must be Matrox cards supported
by the display driver.)
1
Solution
If an unsupported graphics card is plugged into an expansion slot, remove it.
2
Solution
If a graphics adapter is built into your computer motherboard, your system may not have
automatically disabled it when you inserted your Matrox card. Check your system manual for
instructions on how to disable your computers built-in graphics adapter.
3
Cause
Your computer BIOS (Basic Input/Output System) may not be up to date. For more
information on your computer BIOS, see your system manual.
1
Solution
Reinstall your previous graphics card and, if possible, update your computer BIOS. This can
usually be done with software from the manufacturer of your computer. Contact your system
vendor or manufacturer to get a BIOS update for your computer.
To get the correct BIOS update, you may need to know the serial number your computer
displays when it restarts. (This number is usually in the lower-left corner of the display.)
4
Cause
The BIOS of your Matrox graphics card may need to be updated or restored.
NTNT
Matrox Graphics Card User Guide 15
1
Solution
For advanced users
If you have another VGA-compatible graphics card (ISA or PCI), you
can try resetting the BIOS of your Matrox graphics card.
1
Turn off your computer and insert the other graphics card into an expansion slot. For
more information on expansion slots, see Choose an expansion slot, page 3.
2
Plug your monitor into the other graphics card and restart your computer.
3
Make sure
Matrox System Utilities
are installed on your computer. (These can be
installed from your Matrox CD-ROM.)
4
Windows 98/Me/2000 or NT 4.0
Click
#
Run
, type
c:\matrox\util\pbioswin
,
then click
OK
. Follow the on-screen instructions.
DOS
Restart your computer in DOS mode, then type:
cd c:\matrox\util
[Enter]
upbiosdos
[Enter]
5
Turn off your computer, remove the other graphics card, then plug your monitor into
your Matrox graphics card.
6
Restart your computer.
Problem Wrong color balance, screen image off-center, or no picture at all
1
Cause
Your monitor video controls may be improperly set.
1
Solution
Adjust your monitor controls (brightness, contrast, and so on). For more information, see
your monitor manual.
2
Cause
Your monitor may not be properly connected.
1
Solution
Make sure youre using the correct connectors (see Connection setup, page 4) and that all
connectors are properly fastened.
Note:
Make sure your computer uses the other graphics card to control your primary
display. The graphics card that controls your primary display is the one that first displays
information when you restart your computer. (A DualHead-supporting graphics card
may display this startup information on both of its displays at the same time.)
Your computer BIOS (Basic Input/Output System) and the slot type (ISA, PCI, or AGP
see Choose an expansion slot, page 3) of each graphics card help determine which
graphics card controls your primary display.
To control which graphics card is used for your primary display, you may be able to
change the configuration of your computer BIOS. For information on how to change
your computer BIOS settings, see your system manual.
16 Matrox Graphics Card User Guide
2
Solution
Make sure the monitor power cable is firmly in place.
3
Solution
Make sure the connection to the back of the monitor is firmly in place.
If your monitor uses BNC input, make
sure the Red (
R
), Green (
G
), Blue (
B
),
Horizontal Sync (
HSYNC
white or gray
wire), and Vertical Sync (
VSYNC
black
wire) connections are firmly in place and
plugged into the correct input.
3
Cause
If your monitor uses BNC input, one or more connection settings may be incorrect.
1
Solution
Set each of your monitor RGB input and sync switches (if available) to 75 ohms, with the
sync set to external. These controls are usually switches on the back of your monitor.
4
Cause
If display problems occur after the startup screen of your operating system, your software
monitor settings may be incorrect.
1
Solution
Make sure correct software monitor setings are selected.
If your primary display is still usable, see Monitor setup, page 9. Otherwise, see the next
troubleshooting item.
Problem After the startup screen, or after display settings are changed,
the screen image is garbled or unusable
(blank screen, rolling or overlapping screen images)
1
Cause
The Matrox display driver may be trying to use settings your monitor doesnt support. This
can happen if a monitor was never selected in the software and the display resolution was
changed to one your monitor doesnt support, or if the monitor connected to your computer
was changed without changing it in the software.
1
Solution
Windows 98/Me/2000
1
If your primary display is unusable, restart your computer in safe mode (see Restarting
in safe mode, page 13).
2
Right-click the Windows desktop background, then click
Properties
#
Settings
.
3
Move the
Screen area
slider down to its lowest setting, then click
OK
.
Bayonet Nut Connect (BNC)
WARN I N G:
If incorrect software monitor settings are applied,
some
monitors can be
permanently damaged. For more information, see your monitor manual.
9
898
9
8
2k2k
M
eMe
Me
Matrox Graphics Card User Guide 17
4
Restart your computer normally.
5
Make sure the correct monitor is selected in Windows (see Monitor setup, page 9).
6
Make sure youre not using inappropriate monitor setting customizations: Access the
PowerDesk
Monitor Settings
property sheet (see Accessing PowerDesk property sheets,
page 9), then click
Delete all customizations
.
7
Restore your original display settings (see steps 2 and 3).
Windows NT 4.0
1
If your primary display is unusable, restart your computer in VGA mode (see Restarting
in safe mode, page 13).
2
Right-click the Windows desktop background, then click
Properties
#
Settings
.
Windows may prompt you that the display settings are incorrect for the current mode;
click
OK
to continue.
3
Move the
Desktop area
slider down to its lowest setting, then click
OK
.
4
Restart your computer normally.
5
Select a monitor with the Matrox PowerDesk
Monitor
property sheet, then adjust your
display settings. For more information, see the Matrox PowerDesk online
documentation.
2
Cause
Files on your system may have been deleted or corrupted.
1
Solution
Remove, then restore Matrox software:
Windows 98/Me/2000 or NT 4.0
1
If your primary display is unusable, restart your computer in safe mode or VGA mode
(see Restarting in safe mode, page 13).
2
To remove Matrox software, click
#
Settings
#
Control Panel
#
Add/Remove
Programs
(double-click)
#
Matrox Graphics Software (remove only)
#
Add/Remove
#
Yes
.
Note:
In multi-display mode (see DualHead Multi-Display setup), each monitor has its
own monitor settings (refresh rates).
NTNT
Note:
Before removing software, make sure you have all the necessary files to reinstall
software that may still be needed. Also, make sure the display driver you reinstall supports
all
Matrox products in your computer.
18 Matrox Graphics Card User Guide
3
After removing Matrox software, install the latest display driver for your Matrox graphics
card. You may also need to reinstall other Matrox software.
More information
We provide additional documentation in help files,
Readme
files, and Adobe Acrobat PDF (Portable
Document Format) files. To view or print PDF files, use the
Acrobat Reader
program, which you can
install from the Matrox installation CD-ROM. This guide is available on the CD-ROM as a PDF file
(
Doc\English\Guide\Guide_en.pdf
).
The online version of this guide has additional information, including the following sections:
Matrox HeadCasting, TV output, Extra troubleshooting, Display information, Hardware
information, Customer support, Warranty, and Software license agreement. The Extra
troubleshooting section includes more information on the following problems:
Can’t use Windows, Windows reports a
configuration error, and/or can’t install or uninstall
Matrox display driver
Monitor settings aren’t automatically detected
After game for Windows 98/Me/2000 starts,
monitor doesn’t display properly
Setup program reports an IRQ problem
Game for Windows 98/Me doesn’t start or runs
slower than normal
After restarting computer, Windows 98/Me warns
that the graphics card isn’t configured correctly
Using multiple displays under Windows
98/Me/2000 or NT 4.0, program doesn’t work with
main graphics card
Not all graphics cards in the computer are fully
supported
In multi-display mode, displays aren’t numbered
consecutively
Screen image defects appear, program doesn’t run
properly, or Windows doesn’t work properly
Program window or dialog box doesn’t appear on
screen
Display on digital monitor appears blurry or uses
only a portion of the screen
Video file playback is jerky (skipping frames)
Can’t view video
Mouse pointer flickers or disappears when it’s over
a video window
DVD video playback is jerky (skipping frames)
Can’t play certain DVD videos
Can’t record DVD video
TV image is garbled or unusable
Computer text is hard to read with a TV
Poor TV or video recorder image quality
Can’t record video with a video recorder
Sound doesn’t record, video files play back with no
sound, or sound output is distorted or too loud
Note:
Be sure to check for any last-minute release notes at the end of this manual and in the
Matrox CD-ROM
Readme
file. Also, check the Matrox Web site (www.matrox.com/mga) for
the latest Matrox software, technical support, and product information.
Matrox Graphics Card User Guide 19
Matrox HeadCasting
With Matrox
HeadCasting
, you can use real-time 3D animated heads in programs that support this
feature. The 3D head can be an existing one or you can get a customized one (for example, using your
own image). You can use HeadCasting with the following software included with certain Matrox
products:
!
Matrox Virtual Presenter
Enhance Microsoft PowerPoint
presentations with audio and an animated 3D lip-synching head.
After preparing such a presentation, play the presentation with the
included
Matrox Presenter Player
. This player may be distributed
free of charge.
!
LIPSinc HeadFone
Communicate by voice over the Internet
using a 3D lip-synching head.
Getting a Digimask file
To use HeadCasting, you need a Digimask (
*.dmk
) file. You can use Digimask files included
with your Matrox product or supplied by others.
Also, you can get your own custom Digimask file. To do this:
1
Get two digital images of the head you want to use one from
the front and one from the side.
These images need to be Windows bitmaps (
*.bmp
) or JPEG
(
*.jpg
) files. If youre using a standard camera, you can transfer
your pictures to your computer using a scanner. Software for
converting and manipulating digital images is widely available
and is included with most digital cameras and scanners.
2
Install and then run
Digimask LaunchPad
on your computer. To use LaunchPad, your
computer needs an Internet connection. The LaunchPad setup program is included with
your Matrox product or is available on the Web at www.digimask.com
. After starting
LaunchPad, follow the on-screen instructions.
After your Digimask file is sent to you over the Internet, you can use it with other Digimask-
supporting software (for example, Matrox Virtual Presenter). For more information on
using a Digimask file with specific software, see the documentation of that software.
Note:
For more information on the software included with your Matrox product, see the
online documentation included with the software.
20 Matrox Graphics Card User Guide
TV output
You can use the TV output adapter
*
to connect a TV or video
recorder to view or record the secondary display of your
Matrox graphics card. If a TV output adapter wasnt included
with your Matrox product, you can purchase it separately (see
http://shopmatrox.com
). This section describes how to use the
TV output
feature.
Connection setup
1
Turn of f co mpu t er
Windows 98/Me/2000 or NT 4.0
To shut down your computer, click
#
Shut Down
#
Shut down
#
OK
, then turn off your computer.
2
Attach TV adapter
If your Matrox card has an HD-15
connector, attach your Matrox TV
output adapter to this connector. If
youre using an analog
*
dual-monitor
cable, attach your TV output adapter to
the connector labeled
2
(or
2/4
).
*TV output isnt supported with a digital dual-monitor cable.
Note:
TV output isnt supported with full-screen DOS display modes (for example, the
information you see before Windows starts) or with standard VGA mode (for example, when
you restart Windows in safe mode). Older programs may use these display modes. While
one of these display modes is in use, your TV displays nothing (black).
VIDEO OUT
S-VIDEO OUT
TV output adapter
WA R NI N G:
Dont change monitor connections while your computer is turned on. While
your computer is turned on, it may be using monitor settings that are specific to the current
monitor connections.
If a display device (monitor, TV or video recorder) is connected while your computer is using
settings intended for another display device, the display of the new device may be garbled or
unusable.
Some
devices may be permanently damaged if incorrect settings are used.
TV output
adapter
Matrox card
HD-15
connector
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67

Matrox Millennium G550 Manuel utilisateur

Catégorie
Cartes graphiques
Taper
Manuel utilisateur

dans d''autres langues