ASROCK 939Dual-VSTA Guide d'installation

11

1

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

Copyright Notice:Copyright Notice:

Copyright Notice:

No part of this installation guide may be reproduced, transcribed, transmitted, or

translated in any language, in any form or by any means, except duplication of

documentation by the purchaser for backup purpose, without written consent of

ASRock Inc.

Products and corporate names appearing in this guide may or may not be registered

trademarks or copyrights of their respective companies, and are used only for

identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:Disclaimer:

Disclaimer:

Specifications and information contained in this guide are furnished for informational

use only and subject to change without notice, and should not be constructed as a

commitment by ASRock. ASRock assumes no responsibility for any errors or

omissions that may appear in this guide.

With respect to the contents of this guide, ASRock does not provide warranty of any

kind, either expressed or implied, including but not limited to the implied warranties or

conditions of merchantability or fitness for a particular purpose.

In no event shall ASRock, its directors, officers, employees, or agents be liable for

any indirect, special, incidental, or consequential damages (including damages for

loss of profits, loss of business, loss of data, interruption of business and the like),

even if ASRock has been advised of the possibility of such damages arising from any

defect or error in the guide or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

ASRock Website: http://www.asrock.com

Published June 2006

22

2

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

Motherboard LMotherboard L

Motherboard L

ayoutayout

ayout

1 PS2_USB_PWR1 Jumper 18 Chassis Speaker Header (SPEAKER 1)

2 ATX Power Connector (ATXPWR1) 19 Chassis Fan Connector (CHA_FAN1)

3 CPU Fan Connector (CPU_FAN1) 20 Clear CMOS Jumper (CLRTC1)

4 ATX 12V Power Connector (ATX12V1) 21 USB 2.0 Header (USB45, Blue)

5 CPU Heatsink Retention Module 22 Flash Memory

6 939-Pin CPU Socket 23 Floppy Connector (FLOPPY1)

7 2 x 184-pin DDR DIMM Slots 24 Infrared Module Header (IR1)

(Dual Channel A: DDR1, DDR2; Blue) 25 Game Port Header (GAME1)

8 2 x 184-pin DDR DIMM Slots 26 Front Panel Audio Header (AUDIO1)

(Dual Channel B: DDR3, DDR4; Black) 27 JR1 / JL1 Jumper

9 North Bridge Controller 28 PCI Slots (PCI1- 3)

10 Serial ATAII Connector (SATAII_1, red) 29 AGP Slot (1.5V_AGP1)

11 JMicron JMB360 Chipset (PCIE x1 interface) 30 J9 / J10 Jumper

12 South Bridge Controller 31 PCI Express x1 Slot (PCIE2)

13 Secondary Serial ATA Connector (SATA2) 32 J11 Jumper

14 Primary Serial ATA Connector (SATA1) 33 PCI Express x16 Slot (PCIE1)

15 Primary IDE Connector (IDE1, Blue) 34 Future CPU Port (FUTURE_CPU_PORT1)

16 Secondary IDE Connector (IDE2, Black) 35 Internal Audio Connector: CD1 (Black)

17 System Panel Header (PANEL1) 36 J1-J8 Jumpers

33

3

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

ASRock 8CH I/OASRock 8CH I/O

ASRock 8CH I/O

1 Parallel Port 8 Microphone (Pink)

2 RJ-45 Port 9 USB 2.0 Ports (USB01)

3 Side Speaker (Gray) 10 USB 2.0 Ports (USB23)

4 Rear Speaker (Black) 11 Serial Port: COM1

5 Central / Bass (Orange) 12 PS/2 Keyboard Port (Purple)

6 Line In (Light Blue) 13 PS/2 Mouse Port (Green)

*7 Front Speaker (Lime)

* If you use 2-channel speaker, please connect the speaker’s plug into “Front Speaker Jack”. See

the table below for connection details in accordance with the type of speaker you use.

TABLE for Audio Output Connection

Audio Output Channels Front Speaker Rear Speaker Central / Bass Side Speaker

(No. 7) (No. 4) (No. 5) (No. 3)

2 V -- -- --

4 V -- -- V

6V--VV

8 VVVV

44

4

ASRock 939Dual-VSTA Motherboard

1.1.

1.

IntroductionIntroduction

Introduction

Thank you for purchasing ASRock 939Dual-VSTA motherboard, a reliable

motherboard produced under ASRock’s consistently stringent quality control. It de-

livers excellent performance with robust design conforming to ASRock’s commit-

ment to quality and endurance.

This Quick Installation Guide contains introduction of the motherboard and step-by-

step installation guide. More detailed information of the motherboard can be found in

the user manual presented in the Support CD.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change without

notice. In case any modifications of this manual occur, the updated

version will be available on ASRock website without further notice. You

may find the latest VGA cards and CPU support lists on ASRock

website as well.

ASRock website http://www.asrock.com

1.11.1

1.1

Package ContentsPackage Contents

Package Contents

1 x ASRock 939Dual-VSTA Motherboard

(ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm)

1 x ASRock 939Dual-VSTA Quick Installation Guide

1 x ASRock 939Dual-VSTA Support CD

1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)

1 x 3.5-in Floppy Drive Ribbon Cable

1 x Serial ATA (SATA) Data Cable (Optional)

1 x Serial ATA (SATA) HDD Power Cable (Optional)

1 x ASRock 8CH I/O Shield

EnglishEnglish

English

55

5

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

1.21.2

1.2

SpecificationsSpecifications

Specifications

Platform - ATX Form Factor: 12.0-in x 9.6-in, 30.5 cm x 24.4 cm

CPU - Socket 939 for AMD Athlon

TM

64FX / 64X2 / 64 Processors

- Supports AMD’s Cool ‘n’ Quiet

TM

Technology

(see CAUTION 1)

- FSB 1000 MHz (2.0 GT/s)

- Supports Untied Overclocking Technology (see CAUTION 2)

- Supports Hyper-Transport Technology

Chipset - Northbridge: ULi

®

M1695

- Southbridge: ULi

®

M1567

Memory - Dual Channel DDR Memory Technology (see CAUTION 3)

- 4 x DDR DIMM slots

- Support DDR400/333/266

- Max. capacity: 4GB

Hybrid Booster - CPU Frequency Stepless Control (see CAUTION 4)

- ASRock U-COP (see CAUTION 5)

- Boot Failure Guard (B.F.G.)

Expansion Slot - 1 x Future CPU Port (Supports CPU upgrade from AMD K8

939-Pin CPU to AM2 940-Pin CPU through AM2CPU Board)

(see page 13 for details)

- 3 x PCI slots

- 1 x PCI Express x16 slot (see CAUTION 6)

- 1 x PCI Express x1 slot

- 1 x AGP 8X slot (see CAUTION 7)

Audio - C-Media CM6501 7.1 channel audio compliant with UAA

architecture

LAN - Realtek PHY RTL8201CL

- Speed: 10/100 Ethernet

- Supports Wake-On-LAN

Rear Panel I/O ASRock 8CH I/O

- 1 x PS/2 Mouse Port

- 1 x PS/2 Keyboard Port

- 1 x Serial Port: COM1

- 1 x Parallel Port (ECP/EPP Support)

- 4 x Ready-to-Use USB 2.0 Ports

- 1 x RJ-45 Port

- Audio Jack: Side Speaker/Rear Speaker/Central / Bass/

Line in/Front Speaker/Microphone (see CAUTION 8)

66

6

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

Connector - 2 x Serial ATA 1.5Gb/s connectors, support RAID (RAID 0,

RAID 1, JBOD) and “Hot Plug” functions

- 1 x Serial ATAII 3.0Gb/s connector by JMicron JMB 360

(PCIE x1 interface), supports NCQ, AHCI and “Hot Plug”

functions (see CAUTION 9)

- 2 x ATA133 IDE connectors (support 4 x IDE devices)

- 1 x Floppy connector

- 1 x IR header

- 1 x Game header

- CPU/Chassis FAN connector

- 20 pin ATX power connector

- 4 pin 12V power connector

- CD in header

- Front panel audio connector

- 1 x USB 2.0 headers (supports 2 USB 2.0 ports)

(see CAUTION 10)

BIOS Feature - 4Mb AMI BIOS

- AMI Legal BIOS

- Supports “Plug and Play”

- ACPI 1.1 Compliance Wake Up Events

- Supports jumperfree

- SMBIOS 2.3.1 Support

Support CD - Drivers, Utilities, AntiVirus Software (Trial Version)

Hardware - CPU Temperature Sensing

Monitor - Chassis Temperature Sensing

- CPU Fan Tachometer

- Chassis Fan Tachometer

- CPU Quiet Fan

- Voltage Monitoring: +12V, +5V, +3.3V, Vcore

OS - Microsoft

®

Windows

®

2000/XP/XP 64-bit/Vista

TM

compliant

(see CAUTION 11)

Certifications - FCC, CE, Microsoft

®

WHQL Certificated

77

7

ASRock 939Dual-VSTA Motherboard

CAUTION!

1. For power-saving’s sake, it is strongly recommended to enable AMD’s Cool ‘n’

Quiet

TM

technology under Windows system. See APPENDIX on page 45 of

“User Manual” in the support CD to enable AMD’s Cool ‘n’ Quiet

TM

technology.

Since not all K8 939-pin CPU can support AMD’s Cool ‘n’ Quiet

TM

technology,

please check AMD’s website for details.

2. This motherboard supports Untied Overclocking Technology. Please read

“Untied Overclocking Technology” on page 23 for details.

3. This motherboard supports Dual Channel Memory Technology. Before you

implement Dual Channel Memory Technology, make sure to read the

installation guide of memory modules on page 11 for proper installation.

4. Although this motherboard offers stepless control, it is not recommended to

perform over-clocking. Frequencies other than the recommended CPU bus

frequencies may cause the instability of the system or damage the CPU.

5. While CPU overheat is detected, the system will automatically shutdown.

Before you resume the system, please check if the CPU fan on the motherboard

functions properly and unplug the power cord, then plug it back again. To

improve heat dissipation, remember to spray thermal grease between the

CPU and the heatsink when you install the PC system.

6. For the information of the compatible PCI Express VGA cards, please

refer to the “Supported ATi X300 and X300SE Series PCI Express VGA

Card List for PCI Express Slot (PCI Express x16)” on page 9. For the

proper installation of PCI Express VGA card, please refer to the installation

guide on page 13.

7. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!

It may cause permanent damage!

8. For microphone input, this motherboard supports both stereo and mono modes.

For audio output, this motherboard supports 2-channel, 4-channel, 6-channel,

and 8-channel modes. Please check the table on page 3 for proper connection.

9. Before installing SATAII hard disk to SATAII connector, please read the “SATAII

Hard Disk Setup Guide” on page 19 to adjust your SATAII hard disk drive to

SATAII mode. You can also connect SATA hard disk to SATAII connector

directly.

10. Power Management for USB 2.0 works fine under Microsoft

®

Windows

®

Vista

TM

/ XP 64-bit / XP SP1 or SP2 / 2000 SP4.

11. Microsoft

®

Windows

®

Vista

TM

driver is not ready yet. We will update it to

our website in the future. Please visit our website for Microsoft

®

Windows

®

Vista

TM

driver and related information.

ASRock website http://www.asrock.com

EnglishEnglish

English

88

8

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

1.31.3

1.3

Minimum Hardware RMinimum Hardware R

Minimum Hardware R

equirement Tequirement T

equirement T

able for Wable for W

able for W

indowsindows

indows

®®

®

VistaVista

Vista

TMTM

TM

Premium and Basic Logo Premium and Basic Logo

Premium and Basic Logo

For system integrators and users who purchase this motherboard and

plan to submit Windows

®

Vista

TM

Premium and Basic logo, please follow the

below table for minimum hardware requirement. Please adopt the CPU,

memory, and VGA that we suggest.

CPU Athlon 3000+

Memory 512MB Single Channel

VGA DX9.0 with WDDM Driver

with 128bit VGA memory (Premium)

with 64bit VGA memory (Basic)

99

9

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

1.41.4

1.4

SupporSuppor

Suppor

ted Ated A

ted A

Ti X300 and X300SE Series PCI ExpressTi X300 and X300SE Series PCI Express

Ti X300 and X300SE Series PCI Express

VGA Card List for PCI Express Slot (PCI Express x16)VGA Card List for PCI Express Slot (PCI Express x16)

VGA Card List for PCI Express Slot (PCI Express x16)

(for Windows

®

2000/XP/XP 64-bit/Vista

TM

)

Since the margin of ATi X300 and X300SE series PCI Express VGA cards

may vary with different card vendors, we recommend users to adopt the

compatible ATi X300 and X300SE series cards below which have passed

our lab test.

Graphics Chip Model Name Chipset Name

Vendor

ATi ASUS EAX300/TD/128M/A RADEON X300

GIGABYTE GV-RX30128D RADEON X300

GECUBE RADEONR X300 PCIe 128MB RADEON X300

MSI RX300-TD128E RADEON X300

MSI RX300SE-TD128E RADEON X300SE

1010

10

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

2.2.

2.

InstallationInstallation

Installation

Pre-installation PrecautionsPre-installation Precautions

Pre-installation Precautions

Take note of the following precautions before you install mother-

board components or change any motherboard settings.

1. Unplug the power cord from the wall socket before touching any

component. Failure to do so may cause severe damage to the

motherboard, peripherals, and/or components.

2. To avoid damaging the motherboard components due to static

electricity, NEVER place your motherboard directly on the car-

pet or the like. Also remember to use a grounded wrist strap or

touch a safety grounded object before you handle components.

3. Hold components by the edges and do not touch the ICs.

4. Whenever you uninstall any component, place it on a

grounded antstatic pad or in the bag that comes with the

component.

5. When placing screws into the screw holes to secure the

motherboard to the chassis, please do not over-tighten the screws!

Doing so may damage the motherboard.

2.12.1

2.1

CPU InstallationCPU Installation

CPU Installation

Step 1. Unlock the socket by lifting the lever up to a 90° angle.

Step 2. Position the CPU directly above the socket such that the CPU corner with

the golden triangle matches the socket corner with a small triangle.

Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the CPU

into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push

down the socket lever to secure the CPU. The lever clicks on the side tab

to indicate that it is locked.

Step 5. Install CPU fan and heatsink. For proper installation, please kindly refer to

the instruction manuals of your CPU fan and heatsink vendors.

1111

11

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

2.2 Installation of Memory Modules (DIMM)2.2 Installation of Memory Modules (DIMM)

2.2 Installation of Memory Modules (DIMM)

939Dual-VSTA motherboard provides four 184-pin DDR (Double Data Rate)

DIMM slots, and supports Dual Channel Memory Technology. For dual channel

configuration, you always need to install identical (the same brand, speed,

size and chip-type) DDR DIMM pair in the slots of the same color. In other words,

you have to install identical DDR DIMM pair in Dual Channel A (DDR1 and

DDR2; Blue slots; see p.2 No.7) or identical DDR DIMM pair in Dual Channel B

(DDR3 and DDR4; Black slots; see p.2 No.8), so that Dual Channel Memory

Technology can be activated. This motherboard also allows you to install four

DDR DIMMs for dual channel configuration, and please install identical DDR

DIMMs in all four slots. You may refer to the Dual Channel Memory Configuration

Table below.

Dual Channel Memory Configurations

DDR1 DDR2 DDR3 DDR4

(Blue Slot) (Blue Slot) (Black Slot) (Black Slot)

(1) Populated Populated - -

(2) - - Populated Populated

(3)* Populated Populated Populated Populated

* For the configuration (3), please install identical DDR DIMMs in all four slots.

1. If you want to install two memory modules, for optimal compatibility

and reliability, it is recommended to install them in the slots of the

same color. In other words, install them either in the set of blue slots

(DDR1 and DDR2), or in the set of black slots (DDR3 and DDR4).

2. If only one memory module or three memory modules are installed

in the DDR DIMM slots on this motherboard, it is unable to activate

the Dual Channel Memory Technology.

3. If a pair of memory modules is NOT installed in the same Dual

Channel, for example, installing a pair of memory modules in DDR1

and DDR3, it is unable to activate the Dual Channel Memory Tech-

nology .

1212

12

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

Installing a DIMMInstalling a DIMM

Installing a DIMM

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

STEP 1: Unlock a DIMM slot by pressing the retaining clips outward.

STEP 2: Align a DIMM on the slot such that the notch on the DIMM matches the

break on the slot.

The DIMM only fits in one correct orientation. It will cause permanent

damage to the motherboard and the DIMM if you force the DIMM into the

slot at incorrect orientation.

STEP 3: Firmly insert the DIMM into the slot until the retaining clips at both ends

fully snap back in place and the DIMM is properly seated.

1313

13

ASRock 939Dual-VSTA Motherboard

CPU Type Jumper Settings

939-Pin CPU

(Default)

AM2 940-Pin CPU

(Using add-on

ASRock AM2CPU

Board)

J1 J2

J3 J4

J5 J6

J7 J8

J11

J10

J9

J1 J2

J3 J4

J5 J6

J7 J8

J11

J10

J9

2.32.3

2.3

Expansion SlotsExpansion Slots

Expansion Slots

(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)

(Future CPU Port, PCI Slots, PCIE Slots, and AGP Slot)

There are 1 Future CPU Port, 3 PCI slots, 2 PCIE slots, and 1 AGP slot on 939Dual-

VSTA motherboard.

Future CPU Port (Yellow-Colored Port):

Future CPU Port allows you to upgrade your AMD K8 939-Pin CPU to AM2 940-Pin

CPU by installing an add-on ASRock AM2CPU Board into this future CPU Port on

939Dual-VSTA motherboard. Before you upgrade the K8 939-Pin CPU to AM2 940-

Pin CPU, it is necessary to adjust the jumper settings for those required jumpers on

939Dual-VSTA motherboard. Please refer to the table below for the correct jumper

settings.

This yellow-colored Future CPU Port is not an AGP slot! Please do

NOT insert any AGP card into it!

EnglishEnglish

English

1414

14

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

NOTE

When adjusting the jumper settings, you may use the tool, Jumper Cap Remover, to help you

removing the jumper caps more easily. This Jumper Cap Remover is bundled in your motherboard

package, and please follow the “Jumper Cap Remover Instruction” to use it properly.

PCI Slots: PCI slots are used to install expansion cards that have the 32-bit PCI

interface.

PCIE Slots: PCIE1 (PCIE x16 slot) is used for PCI Express cards with x16 lane

width graphics cards. For the information of the compatible PCI

Express VGA cards, please refer to the “Supported ATi X300 and

X300SE Series PCI Express VGA Card List for PCI Express Slot (PCI

Express x16)” on page 9.

PCIE2 (PCIE x1 slot) is used for PCI Express cards with x1 lane

width graphics cards, such as Gigabit LAN card, SATA2 card, etc.

AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has

a special design of clasp that can securely fasten the inserted graphics

card.

Please do NOT use a 3.3V AGP card on the AGP slot of this

motherboard! It may cause permanent damage! For the voltage infor-

mation of your AGP card, please check with the AGP card vendors.

Installing an expansion cardInstalling an expansion card

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power

supply is switched off or the power cord is unplugged. Please read the

documentation of the expansion card and make necessary hardware

settings for the card before you start the installation.

Step 2. Remove the system unit cover (if your motherboard is already installed in

a chassis).

Step 3. Remove the bracket facing the slot that you intend to use. Keep the

screws for later use.

Step 4. Align the card connector with the slot and press firmly until the card is

completely seated on the slot.

Step 5. Fasten the card to the chassis with screws.

Step 6. Replace the system cover.

1515

15

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

2.52.5

2.5

Jumpers SetupJumpers Setup

Jumpers Setup

The illustration shows how jumpers are

setup. When the jumper cap is placed on

pins, the jumper is “Short”. If no jumper cap

is placed on pins, the jumper is “Open”. The

illustration shows a 3-pin jumper whose pin1

and pin2 are “Short” when jumper cap is

placed on these 2 pins.

Jumper Setting

PS2_USB_PWR1 Short pin2, pin3 to enable

(see p.2, No. 1) +5VSB (standby) for PS/2 or

USB wake up events.

Note: To select +5VSB, it requires 2 Amp and higher standby current provided by

power supply.

JR1 JL1 Jumper

(see p.2, No. 27)

Note: If the jumpers JL1 and JR1 are short, both the front panel and the rear panel

audio connectors can work.

Clear CMOS Jumper

(CLRTC1)

(see p.2, No. 20)

Note: CLRTC1 allows you to clear the data in CMOS. The data in CMOS includes

system setup information such as system password, date, time, and system

setup parameters. To clear and reset the system parameters to default setup,

please turn off the computer and unplug the power cord from the power

supply. After waiting for 15 seconds, use a jumper cap to short pin2 and pin3

on CLRTC1 for 5 seconds. However, please do not clear the CMOS right after

you update the BIOS. If you need to clear the CMOS when you just finish

updating the BIOS, you must boot up the system first, and then shut it down

before you do the clear-CMOS action.

2.42.4

2.4

Surround Display FeatureSurround Display Feature

Surround Display Feature

This motherboard supports Surround Display upgrade. With the external add-on

AGP VGA card and PCI Express VGA card, you can easily enjoy the benefits of

Surround Display feature. For the detailed instruction, please refer to the docu-

ment at the following path in the Support CD: ..\ Surround Display Information

Short Open

Clear CMOSDefault

1616

16

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

the red-striped side to Pin1

2.6 Onboard Headers and Connectors2.6 Onboard Headers and Connectors

2.6 Onboard Headers and Connectors

Onboard headers and connectors are NOT jumpers. Do NOT place

jumper caps over these headers and connectors. Placing jumper caps

over the headers and connectors will cause permanent damage of the

motherboard!

•

Floppy Connector

(33-pin FLOPPY1)

(see p.2 No. 23)

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the

connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.2 No. 15) (39-pin IDE2, see p.2 No. 16)

Note: If you use only one IDE device on this motherboard, please set the IDE

device as “Master”. Please refer to the instruction of your IDE device vendor

for the details. Besides, to optimize compatibility and performance, please

connect your hard disk drive to the primary IDE connector (IDE1, blue) and

CD-ROM to the secondary IDE connector (IDE2, black).

Serial ATA Connectors (Black) These two Serial ATA (SATA)

(SATA1: see p.2 No. 14) connectors support SATA data

(SATA2: see p.2 No. 13) cables for internal storage

devices. The current SATA

interface allows up to 1.5 Gb/s

data transfer rate.

It is recommended to plug SATAII HDD to SATAII connector (SATAII_1) and

connect SATA HDD to SATA connector (SATA1 or SATA2).

Serial ATA II Connector (Red) This Serial ATA II (SATA II)

(SATA II_1: see p.2 No. 10) connector supports SATA

data cables for internal storage

devices. The current SATAII

interface allows up to 3.0 Gb/s

data transfer rate.

SATA II_1

SATA1

SATA2

connect the black end

to the IDE devices

connect the blue end

to the motherboard

80-conductor ATA 66/100/133 cable

1717

17

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

Serial ATA (SATA) Please connect the black end of

Power Cable SATA power cable to the power

(Optional) connector on each drive. Then

connect the white end of SATA

power cable to the power

connector of the power supply.

USB 2.0 Header Besides four default USB 2.0

(9-pin USB45) ports on the I/O panel, there is

(see p.2 No. 21) one USB 2.0 header on this

motherboard. This USB 2.0

header cansupport two USB

2.0 ports.

Infrared Module Header This header supports an

(5-pin IR1) optional wireless transmitting

(see p.2 No. 24) and receiving infrared module.

Internal Audio Connectors This connector allows you

(4-pin CD1) to receive stereo audio input

(CD1: see p.2 No. 35) from sound sources such as

a CD-ROM, DVD-ROM, TV

tuner card, or MPEG card.

Front Panel Audio Header This is an interface for front

(8-pin AUDIO1) panel audio cable that allows

(see p.2 No. 26) convenient connection and

control of audio devices.

Serial ATA (SATA) Either end of the SATA data cable

Data Cable can be connected to the SATA /

(Optional) SATAII hard disk or the SATA /

SATAII connector on the

motherboard.

CD1

connect to the

power supply

connect to the SATA

HDD power connector

1818

18

ASRock 939Dual-VSTA Motherboard

System Panel Header This header accommodates

(9-pin PANEL1) several system front panel

(see p.2 No. 17) functions.

Chassis Speaker Header Please connect the chassis

(4-pin SPEAKER 1) speaker to this header.

(see p.2 No. 18)

Chassis Fan Connector Please connect a chassis fan

(3-pin CHA_FAN1) cable to this connector and

(see p.2 No. 19) match the black wire to the

ground pin.

CPU Fan Connector Please connect the CPU fan

(4-pin CPU_FAN1) cable to this connector and

(see p.2 No. 3) match the black wire to the

ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.

(see p.2 No. 2)

ATX 12V Power Connector Please note that it is necessary

(4-pin ATX12V1) to connect a power supply with

(see p.2 No. 4) ATX 12V plug to this connector.

Failing to do so will cause power

up failure.

Game Port Header Connect a Game cable to this

(15-pin GAME1) header if the Game port bracket

(see p.2 No. 25) is installed.

EnglishEnglish

English

1919

19

ASRock 939Dual-VSTA Motherboard

EnglishEnglish

English

The above examples are just for your reference. For different SATAII hard

disk products of different vendors, the jumper pin setting methods may not

be the same. Please visit the vendors’ website for the updates.

2.72.7

2.7

SASA

SA

TT

T

AII Hard Disk Setup GuideAII Hard Disk Setup Guide

AII Hard Disk Setup Guide

Before installing SATAII hard disk to your computer, please carefully read below

SATAII hard disk setup guide. Some default setting of SATAII hard disks may not

be at SATAII mode, which operate with the best performance. In order to enable

SATAII function, please follow the below instruction with different vendors to

correctly adjust your SATAII hard disk to SATAII mode in advance; otherwise, your

SATAII hard disk may fail to run at SATAII mode.

Western Digital

If pin 5 and pin 6 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the

jumpers from pin 5 and pin 6.

SAMSUNG

If pin 3 and pin 4 are shorted, SATA 1.5Gb/s will be enabled.

On the other hand, if you want to enable SATAII 3.0Gb/s, please remove the

jumpers from pin 3 and pin 4.

HITACHI

Please use the Feature Tool, a DOS-bootable tool, for changing various ATA

features. Please visit HITACHI’s website for details:

http://www.hitachigst.com/hdd/support/download.htm

2020

20

ASRock 939Dual-VSTA Motherboard

2.82.8

2.8

Serial ASerial A

Serial A

TT

T

A (SAA (SA

A (SA

TT

T

A) / Serial AA) / Serial A

A) / Serial A

TT

T

AII (SAAII (SA

AII (SA

TT

T

AII) Hard DisksAII) Hard Disks

AII) Hard Disks

InstallationInstallation

Installation

This motherboard adopts JMicron JMB360 chipset that supports Serial ATAII

(SATAII) hard disk. It also adopts ULi

®

M1567 south bridge chipset that supports

Serial ATA (SATA) hard disks, and supports RAID functions. You may install SATA /

SATAII hard disks on this motherboard for internal storage devices. This section

will guide you to install the SATA / SATAII hard disks.

STEP 1: Install the SATA / SATAII hard disks into the drive bays of your chassis.

STEP 2: Connect the SATA power cable to the SATA / SATAII hard disk.

STEP 3: Connect one end of the SATA data cable to the motherboard’s SATA /

SATAII connector.

STEP 4: Connect the other end of the SATA data cable to the SATA / SATAII hard

disk.

1. If you plan to use RAID 0, RAID 1, or JBOD functions on SATA, SATA

HDDs must be operated in “RAID” mode.

2. “RAID” and “non-RAID” mode are options under “SATA Operation Mode” in

BIOS setup. Please refer to page 35 of “User Manual” in the support CD

for details. They need different drivers during actual operation.

2.9 Hot Plug and Hot Swap F2.9 Hot Plug and Hot Swap F

2.9 Hot Plug and Hot Swap F

unctions for SAunctions for SA

unctions for SA

TT

T

A / SAA / SA

A / SA

TT

T

AIIAII

AII

HDDsHDDs

HDDs

939Dual-VSTA motherboard supports Hot Plug and Hot Swap functions for SATA /

SATAII Devices.

NOTE

What is Hot Plug Function?

If the SATA / SATAII HDDs are NOT set for RAID configuration, it is called

“Hot Plug” for the action to insert and remove the SATA / SATAII HDDs

while the system is still power-on and in working condition.

However, please note that it cannot perform Hot Plug if the OS has been

installed into the SATA / SATAII HDD.

What is Hot Swap Function?

If SATA / SATAII HDDs are built as RAID1 then it is called “Hot Swap” for

the action to insert and remove the SATA / SATAII HDDs while the system

is still power-on and in working condition.

EnglishEnglish

English

La page charge ...

ASROCK 939Dual-VSTA Guide d'installation

ASROCK 939Dual-VSTA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents