Honeywell 19908AJ Le manuel du propriétaire

1 69-0628B—1

69-0628B-1

Heating or Cooling Thermostat and

Wallplate or Heating/Cooling

Thermostat and Subbase

T8090A/191108AJ, Q682

OWNER’S MANUAL

2 69-0628B—1

M3375

Welcome to the world of energy savings with your new Honeywell fuel saver thermostat. The

Honeywell name is your assurance of accurate control and reliable operation for years to come.

Your new thermostat will automatically lower and raise the temperature in your home one or

more times every 24 hours. This allows you to significantly lower your fuel costs, while awakening

(or returning home) to a comfortable temperature.

Read this manual to learn how to use your new thermostat.

Recycling Notice

This control contains mercury in a sealed tube. Do

not

place control in the trash at the end of its

useful life.

If this control is replacing a control that contains mercury in a sealed tube, do

not

place your

control in the trash.

Contact your local waste management authority for instructions regarding recycling and the

proper disposal of this control, or of an old control containing mercury in a sealed tube.

If you have questions, call Honeywell Inc. at 1-800-468-1502.

3 69-0628B—1

Table of Contents

PAGE

Features of Your Thermostat ............................................................................................................ 4

Setting the Temperature ................................................................................................................... 7

Setting Subbase Switches ................................................................................................................ 8

Inserting Clock Batteries ................................................................................................................... 9

Setting the Clock ............................................................................................................................. 10

Programming................................................................................................................................... 11

Troubleshooting .............................................................................................................................. 14

Servicing the Thermostat ................................................................................................................ 23

Cycle rate adjustment ................................................................................................................ 23

Thermometer adjustment ........................................................................................................... 24

Warranty.......................................................................................................................................... 27

4 69-0628B—1

2

1

3

M8895

Features of Your Thermostat

1 FLIP-UP COVER. Lift it up to set clock for

energy savings and normal temperature

periods.

2 THERMOSTAT COVER. Lift up and

remove to adjust heat anticipator.

3 THERMOMETER. Provides accurate room

temperature reading.

4 CLOCK. This clock provides a 24-hour

slotted dial to hold the programming pins.

5 CLOCK HANDS. Turn minute hand clock-

wise  to match the correct AM or PM

time to the time indicator.

6 TIME INDICATOR. Arrow head indicates

time for 24-hour dial.

7 PROGRAM INDEX WHEEL. Controls high

and low temperature at specific time of day

as set by program pins.

8 TEMPERATURE SETTING LEVERS.

Left (blue mark) controls the low tempera-

ture; right (red mark) controls the high

temperature.

5 69-0628B—1

5

8

9

76

11

12

13

10

14

M8896

4

9 PROGRAM PINS. Must be inserted into

24-hour clock dial slots to control program

index wheel.

10 PIN SLOTS. Located on 24-hour dial at

10-minute intervals for program pin

insertion.

11 MANUAL PROGRAM ADVANCE BUTTON.

Allows change from comfort to energy

savings setting and vice versa without

changing the program.

12 HEAT ANTICIPATOR SCALEPLATE.

Calibrated to match the heating system

current draw in amperes.

13 ANTICIPATOR SETTING LEVER. Must be

adjusted to match the heating system

primary control current.

14 MERCURY BULB AND BIMETAL ELE-

MENT (2). Provide automatic temperature

control by switching the heating or cooling

system on or off.

6 69-0628B—1

AUTO OFF

COOL

HEATON

FAN

B

O

W

Y

R

G

M 719

16

M2421

15

15 WALLPLATE. Provides mounting base and

wiring connections for heating-only or

cooling-only thermostat.

16 SUBBASE. Provides mounting base, wiring

connections and manual switching control

for heating/cooling thermostat.

7 69-0628B—1

8

9

1

0

1

2

11

1

2

3

4

5

6

7

8

9

1

0

12

11

1

2

3

4

5

6

7

12

6

3

9

HIGH

TEMPERATURE

SETTING LEVER

(RED MARK)

LOW TEMPERATURE

SETTING LEVER

(BLUE MARK)

M1691

Setting the Temperature

For Heating

Set the left lever (blue mark) to the energy

savings temperature you want when you are

sleeping or your home is unoccupied.

Set the right lever (red mark) to the tempera-

ture you want for normal comfort periods.

NOTE: You may override the time program by

setting both the red and blue levers to the

same temperature setpoint.

For Cooling

Set the left lever (blue mark) to the tempera-

ture you want for normal comfort periods.

Set the right lever (red mark) to the energy

savings temperature you want when you are

sleeping or your home is unoccupied.

Fig. 1—Setting High and Low Temperature

Setting Levers.

8 69-0628B—1

Setting Subbase Switches

(If applicable)

The subbase system switch controls system

operation as follows:

HEAT—Heating system is controlled by the

thermostat. Cooling system is off.

COOL—Cooling system is controlled by the

thermostat. Heating system is off.

OFF—Both the heating and cooling systems

are off. If the fan switch is at the AUTO

position, the fan is also off.

AUTO—In a cooling only application, only

cooling operates. In a heating only applica-

tion, only heating operates.

The subbase fan switch controls fan operation

as follows:

ON—Fan operates continuously.

AUTO—Fan operates with cooling equipment

as controlled by the thermostat or with the

heating equipment as controlled by the

plenum fan switch. In electric heat, heat

pump, and fan coil systems, the fan is

controlled by the thermostat in heating and

cooling.

To switch positions, use thumb or index

finger to slide lever to desired position. For

proper circuit operation, stop switch lever in the

detent over desired function indicator mark.

9 69-0628B—1

BATTERY LOCATION FOR

(2) AAA BATTERIES;

INSTALL WITH POSITIVE

ENDS UP

M7188

Inserting Clock Batteries

Power is supplied to the clock by the 24 Vac

transformer, by two AAA alkaline batteries

(included), or by the heating or cooling control

circuit. Backup batteries can be installed to

supply power to the clock if power is interrupted

when using 24 Vac powering method. Install

batteries in thermostat as shown in Fig. 2. Once

a year or when batteries are dead, replace with

two new AAA alkaline batteries. We recom-

mend Energizer

®

batteries.

Fig. 2—Inserting Clock Batteries.

10 69-0628B—1

TIME

INDICATOR

ARROW

MINUTE

HAND

M8561

Setting the Clock

Lift thermostat flip-up cover and you will find

the 24-hour program dial, slotted in ten minute

increments. Adjust the clock to the current time

by moving the minute hand carefully in a clock-

wise direction. DO NOT reverse the

minute hand.

When time is correctly set, the Time Indica-

tor Arrow (see Fig. 3) points to the correct time

and corresponding daytime (light) or nighttime

(dark) band of the program dial.

EXAMPLE: For 11 PM, the time indicator arrow

points directly to dark band. For 11 AM, the

arrow points to the light band on the dial.

Daylight Savings Time

When Daylight Savings Time starts, carefully

move the minute hand in a clockwise

direction one hour. When Daylight Savings Time

ends, carefully move the minute hand in a

clockwise direction 23 hours. Do NOT

reverse the minute hand, or damage to the timer

mechanism can occur.

Fig. 3—Setting the Clock.

11 69-0628B—1

Programming

You can program your thermostat to

automatically lower and raise the temperature

one or more times every 24 hours, depending

on the number of program pins used.

Before setting your program

Lift thermostat flip-up cover and you will find

the 24-hour program dial. The slots on the

program dial (Fig. 4) are for the program pins

that can be inserted at ten minute intervals.

Three red and three blue program pins are

included with your thermostat. The red pins start

the high-temperature period; the blue pins start

the low-temperature period. A heating program

has been preprogrammed. A red pin is inserted

at 6:00 AM for high temperature (comfort period);

a blue pin is inserted at 10:00 PM for low

temperature (energy saving period). Two

additional sets of pins are located in the program

pin storage area. You can set up to six tem-

perature changes with the pins supplied. We

recommend at least five hours for each energy

saving period.

To change the pins or add a new energy

savings period—

• To insert a pin, push it straight into the selected

notch on the program dial until it is completely

seated.

• To remove a pin, press against the program dial

and pull the pin straight out. DO NOT attempt to

change a pin if it is engaged with the program

index wheel.

• On heating/cooling systems, you must reset the

pins when the seasons change. You will also

probably want to change the lever positions.

12 69-0628B—1

24-HOUR PROGRAM DIAL

(GRAY AREA FOR

NIGHT SETTINGS)

FLIP-UP

COVER

PROGRAM

PINS

THERMOSTAT

COVER

PROGRAM PIN SLOT

PROGRAM INDEX WHEEL

PROGRAM PIN

STORAGE

TIME INDICATOR

ARROW

MANUAL PROGRAM

ADVANCE BUTTON

M8692

Fig. 4—Program Components.

Setting the Heating Program

Decide when you want the temperature to

reach the comfort level. Find the notch on the

dial that is one-half hour before this time and

insert a

red

pin. The half-hour head start gives

the furnace time to heat the house before you

wake up or arrive home.

Decide when you want the energy savings

period to start and insert a

blue

pin at the notch

that corresponds to this time. After the blue pin

engages, the furnace will be off until room

temperature drops to the energy savings set

point.

You can set both a day and a night program.

See Fig. 5 for program examples.

13 69-0628B—1

WINTER SUMMER

TEMPERATURE

PROGRAM

PIN IN

CONTROL

NIGHT

ENERGY

SAVING

PERIOD

DAY

ENERGY

SAVING

PERIOD

BEGINS

10:00 PM

ENDS

6:00 AM

BEGINS

7:30 AM

ENDS

4:00 PM

TEMPERATURE

PROGRAM

PIN IN

CONTROL

°C

27

24

27

24

RED

BLUE

RED

BLUE

°F

58

68

58

68

°C

14

20

14

20

°F

80

75

80

75

BLUE

RED

BLUE

RED

M1690B

Fig. 5—Program Examples.

Setting the Cooling Program

Decide when you want the temperature to

reach the comfort level. Find the notch on the dial

that is one-half hour before this time and insert a

blue

pin. The half-hour head start gives the air

conditioner time to cool the house before you

wake up or arrive home.

Decide when you want the energy savings

period to start and insert a

red

pin in the notch

that corresponds to this time. After the red pin

engages, the air conditioner will be off until room

temperature rises to the energy savings setpoint.

NOTE: Due to weather and system variations,

the program pins may need to be relocated for

optimum start time of heating or cooling equip-

ment during recovery from energy savings.

14 69-0628B—1

Start or End Programs with

Manual Program Advance Button

IMPORTANT:

To prevent damage to the

program advance mechanism. DO NOT

use the program advance button within a

30-minute period before or after a program

change.

The manual program advance button enables

immediate, one-time-only program changes to

accommodate temporary schedule changes.

Press the button to immediately begin an

energy savings period or return to the normal

setting. After pressing the button, check the

program indicator to ensure the system is in the

desired mode. If the program indicator shows

blue, the lower temperature is in effect; if it shows

red, the higher temperature is in effect. Using the

manual advance button will not affect the stored

program.

15 69-0628B—1

Problem Check Action

No heat. — system switch. May be in OFF

or COOL position. 1

Move system switch to HEAT position.

— fuse or circuit breaker. If blown or tripped, replace fuse or reset breaker.

— furnace power switch. May be

Off.

Move switch to ON .

— pilot flame. May be out. Relight pilot flame per furnace manufacturer’s

instructions.

— thermostat connections. Turn Off power to furnace. Check for correct

terminal hookups. Repair any frayed or broken

wires. Firmly tighten all terminal screws. Turn

power On.

1 Applicable to heating-cooling subbase only.

Continued

Troubleshooting

Your Honeywell thermostat requires little or no attention. Most problems can generally be traced

to the following:

16 69-0628B—1

Troubleshooting (Continued)

Problem Check Action

No heat (continued). — other. Contact a qualified service technician for

assistance.

Energy savings

temperature program

12 hours off.

— program dial for proper day or

night phase.

Turn clock ahead 12 hours. Move minute hand

clockwise only.

Rooms do not warm

up at programmed

time.

— timer program for heating

system. May need more time

to warm up rooms.

Move red pin one-half hour earlier on the

program dial.

Temperature change

occurs at the wrong

time.

— program pins for correct time

locations.

Relocate pins to desired settings.

Room temperatures

are not correct.

— positions of thermostat set

point levers.

Reset to desired temperatures.

— position of subbase system

switch. 1

Move to desired operating position.

Continued

17 69-0628B—1

Troubleshooting (Continued)

Continued

Problem Check Action

Room temperatures

are not correct

(continued).

— thermostat circuits. HEATING-ONLY SYSTEM—Move temperature

setting levers 5°F (3°C) above room temp-

erature. Heating system should start. If the

system does not operate, call a qualified

service technician.

COOLING-ONLY SYSTEM—Move temperature

setting levers 5°F (3°C) below room temp-

erature. Cooling system should start. If the

system does not operate, call a qualified

service technician.

HEATING/COOLING SYSTEM—With system

switch at HEAT, move temperature setting

levers 5°F (3°C) above room temperature.

Heating system should start. With system

switch at COOL, move temperature setting

levers 5°F (3°C) below room temperature.

Cooling system should start. If the systems do

not operate, call a qualified service technician.

1 Applicable to heating-cooling subbase only.

18 69-0628B—1

Troubleshooting (Continued)

1 Applicable to heating-cooling subbase only.

Problem Check Action

Burner-on time too

short.

— anticipator setting. (See Fig. 6

for anticipator location.)

Increase anticipator setting by 0.05. Observe

burner operation.

Burner-on time too

long.

— anticipator setting. (See Fig. 6

for anticipator location.)

Decrease anticipator setting by 0.05. Observe

burner operation.

No cooling. — system switch. May be in OFF

or HEAT position. 1

Move switch to COOL position.

— fuse or circuit breaker. If fuse is blown or breaker tripped, replace or

reset.

— condenser switch position.

Located outdoors and may be

turned Off.

Move to ON position.

Continued

19 69-0628B—1

Troubleshooting (Continued)

Continued

Problem Check Action

No cooling

(continued).

— thermostat connections. Check

for correct terminal hookups.

Repair any frayed or broken

wires. Firmly tighten all

terminal screws.

Turn Off power to cooling system.

— other. Contact a qualified service technician for

assistance.

Thermostat setting

and thermometer

reading disagree.

— level position of thermostat. Reinstall thermostat wallplate or subbase. Use a

spirit level.

— area around thermostat for

drafts or radiant heat.

Thermostat should be about 5 ft (1.5 m)above

floor on an inside wall. Contact qualified service

technician for change of location.

— calibration of thermometer. See instructions in Thermometer Adjustment

section.

20 69-0628B—1

Problem Check Action

Clock does not run. — thermostat connections at the

two C terminals. If no

connections, clock needs

batteries in order to run.

Batteries may not have been

installed. 2

Install batteries as shown in Fig. 2.

— Batteries may need

replacement.

Replace with two new AAA alkaline batteries as

shown in Fig. 2.

— if new batteries are installed

and clock still does not run.

Replace thermostat.

— voltage across the two

C terminals.

Remove thermostat from the wallplate or

subbase and measure the voltage. Refer to the

Voltage at Clock Terminals table for cause and

reaction.

Troubleshooting (Continued)

1 Applicable to heating-cooling subbase only.

2 If clock is not battery powered, clock can use batteries for backup.

Continued

La page est en cours de chargement...

Honeywell 19908AJ Le manuel du propriétaire

Ce manuel convient également à

Honeywell 19908AJ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents