STIEBEL ELTRON VRC-W 400 (E) Operation Instruction

OPERATION AND INSTALLATION

UTILISATION ET INSTALLATION

BEDIENING EN INSTALLATIE

Central ventilation appliance with heat recovery | VMC centralisée avec récupération

de chaleur | Centraal ventilatietoestel met warmteterugwinning

» VRC-W 400

» VRC-W 400 E

2 | VRC-W 400 (E) www.stiebel-eltron.com

CONTENTS | SPECIAL INFORMATION

SPECIAL INFORMATION

OPERATION

1. General information ��3

1.1 Safety instructions �� 3

1.2 Other symbols in this documentation �� 3

1.3 Information on the unit �� 3

1.4 Standardised output data �� 3

1.5 Units of measurement �� 3

2. Safety �� 4

2.1 Intended use �� 4

2.2 General safety instructions �� 4

2.3 Test symbols �� 4

3. Appliance description ��4

3.1 Frost protection �� 4

3.2 Bypass function �� 4

4. Settings ��5

4.1 Switching the appliance on �� 5

4.2 Programming unit �� 5

4.3 Selecting the fan stage �� 6

4.4 Activating time programs �� 6

4.5 Menu �� 6

4.6 Switching off the appliance �� 8

5. Maintenance, cleaning and care ��8

5.1 Replacement ﬁlters �� 8

5.2 Filter inspection and replacement �� 8

6. Troubleshooting ��9

INSTALLATION

7. Safety �� 10

7.1 General safety instructions �� 10

7.2 Instructions, standards and regulations �� 10

7.3 Operation of the appliance in buildings with

combustion equipment �� 10

7.4 Operating the appliance in passive houses �� 11

8. Appliance description �� 11

8.1 Standard delivery �� 11

8.2 Accessories �� 11

9. Preparation �� 11

9.1 Storage �� 11

9.2 Installation site �� 11

9.3 Transport �� 12

10. Installation �� 12

10.1 Removing the front panel �� 12

10.2 Mounting the appliance ��13

10.3 Connecting the condensate drain hose ��13

10.4 Air ducts �� 14

10.5 Fitting the front panel ��15

10.6 Electrical connection �� 15

11. Commissioning �� 16

11.1 Initial start-up �� 16

11.2 Recommissioning �� 16

12. Settings �� 17

12.1 Parameter �� 17

12.2 Actual values �� 19

12.3 Code �� 19

13. Appliance shutdown �� 19

14. Maintenance �� 19

15. Troubleshooting �� 21

16. Disposal �� 22

17. Speciﬁcation �� 23

17.1 Dimensions and connections �� 23

17.2 Wiring diagram �� 23

17.3 Fan diagram �� 25

17.4 Data table �� 26

GUARANTEE

ENVIRONMENT AND RECYCLING

SPECIAL INFORMATION

- The appliance may be used by children over 8

years of age and persons with reduced physical,

sensory or mental capabilities or a lack of ex-

perience and expertise, provided that they are

supervised or they have been instructed on how

to use the appliance safely and have understood

the potential risks. Children must never play with

the appliance. Cleaning and user maintenance

must not be carried out by children without

supervision.

- The power cable must only be replaced (for ex-

ample if damaged) by a qualiﬁed contractor au-

thorised by the manufacturer, using an original

spare part.

- Fix the appliance in position as described in

chapter "Installation/ Preparations".

OPERATION

General information

www.stiebel-eltron.com VRC-W 400 (E) | 3

ENGLISH

OPERATION

1. General information

The chapters "Special information" and "Operation" are intended

for both users and qualiﬁed contractors. The chapter "Installation"

is intended for qualiﬁed contractors.

Note

Read these instructions carefully before using the appli-

ance and retain them for future reference. Pass on these

instructions to a new user if required.

1.1 Safety instructions

1.1.1 Structure of safety instructions

!

KEYWORD Type of risk

Here, possible consequences are listed that may result

from failure to observe the safety instructions.

f Steps to prevent the risk are listed.

1.1.2 Symbols, type of risk

Symbol Type of risk

Injury

Electrocution

Burns

(burns, scalding)

1.1.3 Keywords

KEYWORD Meaning

DANGER Failure to observe this information will result in serious

injury or death.

WARNING Failure to observe this information may result in serious

injury or death.

CAUTION Failure to observe this information may result in non-seri-

ous or minor injury.

1.2 Other symbols in this documentation

Note

General information is identiﬁed by the adjacent symbol.

f Read these texts carefully.

Symbol Meaning

Material losses

(appliance damage, consequential losses and environmen-

tal pollution)

Appliance disposal

f This symbol indicates that you have to do something. The ac-

tion you need to take is described step by step.

1.3 Information on the unit

Connections

Symbol Meaning

Outdoor air

Exhaust air

Extract air

Supply air

1.4 Standardised output data

Information on determining and interpreting the speciﬁed stand-

ardised output data

Standard : EN 13141-7

The output data speciﬁcally mentioned in text, diagrams and

technical datasheets has been determined in line with the test

conditions described in the standard shown in the heading of

this chapter.

Generally, these standardised test conditions will not fully meet

the conditions found at the installation site of the system user.

Depending on the chosen test method and the extent to which

the selected method deviates from the conditions described in

the standard shown in the heading of this chapter, any deviations

can have a considerable impact. Additional factors that have an

inﬂuence on the test values are the measuring equipment, the

system conﬁguration, the age of the system and the ﬂow rates.

A conﬁrmation of the speciﬁed output data can only be obtained

if the conditions applicable to the relevant test match those of the

standard shown in the heading of this chapter.

1.5 Units of measurement

Note

All measurements are given in mm unless stated oth-

erwise.

!

OPERATION

Safety

4 | VRC-W 400 (E) www.stiebel-eltron.com

2. Safety

2.1 Intended use

The appliance is designed as a mechanical ventilation unit with

central supply and extract air routing.

The appliance is intended for domestic use. It can be used safely

by untrained persons.

The appliance can also be used in non-domestic environments,

e.g. in small businesses, as long as it is used in the same way. Any

other use beyond that described shall be deemed inappropriate.

Observation of these instructions and of the instructions for any

accessories used is also part of the correct use of this appliance.

It is deemed inappropriate to:

- Use extract air containing grease, explosive gases, dust or

adhesive aerosols

- Connect cooker hoods or vented tumble dryers to the ventila-

tion system

Never adjust the settings of supply and extract air vents inside the

rooms. These have been set up by a qualiﬁed contractor during

commissioning.

2.2 General safety instructions

!

WARNING Injury

The appliance may be used by children over 8 years of

age and persons with reduced physical, sensory or men-

tal capabilities or a lack of experience and expertise,

provided that they are supervised or they have been

instructed on how to use the appliance safely and have

understood the potential risks. Children must never play

with the appliance. Cleaning and user maintenance must

not be carried out by children without supervision.

WARNING Injury

The discharged cold air can cause condensation to be

formed in the vicinity of the air discharge.

f Ensure that no risk of slipping due to wet conditions

or ice formation occurs on adjacent footpaths and

driveways at low temperatures.

2.3 Test symbols

See type plate on the appliance.

3. Appliance description

The appliance draws in outdoor air with a fan. A second fan ex-

tracts stale air from the rooms containing odours or moisture,

e.g. kitchen, bathroom, WC. Extract air and outdoor air are routed

through separate air ducts. Extract air and outdoor air are ﬁltered

by separate ﬁlters.

The extract air and outdoor air ﬂow through a cross-countercur-

rent heat exchanger. The outdoor air absorbs heat taken from the

extract air. This enables a large proportion of thermal energy to

be recovered.

The air ﬂow rate is preset for each fan stage by the qualiﬁed con-

tractor during commissioning. Constant ﬂow rate control ensures

that the air ﬂow rates through the supply air and extract air fans

are achieved irrespective of the duct pressure.

Stage Display

Ventilation

for humidity

protection

0

"Power"

symbol and

digit0

Necessary ventilation for ensuring that

the building structure is protected under

normal conditions of use with somewhat

reduced moisture loads, e.g. during tem-

porary absence of users and no drying of

washing in the residential unit.

Reduced

ventilation

1

"Fan" symbol

and digit1

Reduced ventilation is the ventilation

necessary to meet hygiene standards and

ensure protection of the building structure

(moisture level) under standard conditions

of use with partially reduced moisture and

pollutant loads, e.g. as a result of intermit-

tent user absence.

Standard

ventilation

2

"Fan" symbol

and digit2

Standard ventilation is the ventilation

necessary to meet hygiene standards and

ensure protection of the building structure

when users are present.

Intensive

ventilation

3

“Fan” sym-

bol and

digit3

Intensive ventilation is increased ventila-

tion with a higher flow rate to reduce load

peaks, e.g. for rapid ventilation during or

after a party. You can switch on intensive

ventilation with the "intensive ventilation"

button. Alternatively, you can switch on the

intensive ventilation with an optional ex-

ternally connected switch or button.

VRC-W 400 E : Enthalpy heat exchanger

The enthalpy heat exchanger is a highly efﬁcient, moisture-trans-

ferring countercurrent heat exchanger with a selective membrane.

The membrane helps to recover moisture from the extract air and

transfer it to the supply air. This prevents the relative humidity

in the rooms from dropping too low during the winter months.

3.1 Frost protection

The appliance has a frost protection controller, which ensures that

it works to optimum effect even at low outside temperatures. If the

outdoor air temperature falls below the selected frost protection

value, the electric preheating coil is switched on. This prevents the

cross-countercurrent heat exchanger from freezing up. When the

preheating coil is active, the "frost protection" symbol illuminates

on the display.

3.2 Bypass function

The appliance has an integral bypass damper. The bypass damper

enables the supply of fresh air which does not ﬂow through the

heat exchanger. You can specify the operating mode of the bypass

damper with one parameter on the programming unit (see chapter

"Settings/ Parameters").

Utilising cool outdoor air

Cool, fresh air is required on summer nights in particular. In such

cases, in automatic mode, as much of the warm air in the home

as possible is displaced by cooler fresh air.

Utilising warm outdoor air

In spring and autumn, the appliance can increase the room tem-

perature by opening the bypass damper in automatic mode and

drawing warmer outdoor air into the building.

OPERATION

Settings

www.stiebel-eltron.com VRC-W 400 (E) | 5

ENGLISH

4. Settings

4.1 Switching the appliance on

D0000064394

f Plug the appliance into a standard socket.

4.2 Programming unit

An external programming unit can be connected to the appliance

in addition to the factory-installed programming unit.

D0000040582

1

4

5

6

7

3

8

2

1 Upper display: Fan stage, parameter number or number of

an actual value

2 Lower display: Values (e.g. temperature or air ﬂow rate)

3 Touch-Wheel

4 "MENU" button

5 "HOME" button

6 "OK" button

7 "Intensive ventilation" button

8 "Intensive ventilation" indicator

4.2.1 Controls

Controls Description

"MENU" button

Press this button for approx. one second to call up the menu

from the standard display.

Within the menu, press this button to return to the beginning

of the menu. Parameter P1 is displayed.

When setting a parameter value, press this button to exit set-

ting of the parameter. Any changes made will not be saved.

"OK" button

In order to set the parameter, you must first make it editable

by pressing the "OK" button. Then you can change the value

with the Touch-Wheel.

Once you have set the parameter, confirm your entry with the

"OK" button.

"HOME" button Calls up the standard display

"Intensive ven-

tilation" button

Use this button to switch the appliance to intensive venti-

lation. You can set the runtime for intensive ventilation in

parameter P2. Once this runtime has expired, the appliance

returns to the previously applicable fan stage.

Touch-Wheel

From the home screen, you can use the Touch-Wheel to

select fan stages 0, 1 and 2, and activate the time programs.

The "time" symbol indicates that time programs are activat-

ed.

Use the Touch-Wheel to select a parameter or value in the

menu.

If you turn the Touch-Wheel quickly, the increment size

changes after a while.

Press the "HOME" and "OK" buttons simultaneously to activate the

function block. The "padlock" symbol appears. Then you can wipe

the programming unit clean without inadvertently changing any

settings. Press the "HOME" and "OK" buttons simultaneously for

two seconds to deactivate the function block.

4.2.2 Display

If no user action occurs within the time selected in the illumination

duration parameter, the display backlighting switches off and the

standard display appears.

Press any button to switch the background lighting on again.

Symbol Description

Power : This symbol indicates that the appliance is switched on

and the fans are operating in "humidity protection" mode.

Time : This symbol indicates that the appliance is operating in time

program mode. Depending on the program, the appliance is oper-

ated at different fan stages.

Fan : This symbol, with the associated digit, indicates the fan

stage at which the appliance is currently running. If the unit has

switched off the fans to prevent condensate, the "Fan" symbol

flashes.

Bypass active : This symbol indicates that the air flow is bypassing

the heat exchanger. No heat is recovered.

This symbol is displayed when the function block is activated.

Press the "HOME" and "OK" buttons simultaneously for two sec-

onds to deactivate the function block.

Filters : Change the filter when this symbol appears.

Frost protection : This symbol is displayed when the appliance has

turned on the preheating coil for frost protection.

Service/fault : The "service/fault" symbol illuminates permanently

in the event of faults that do not impair the basic function of the

appliance. The "service/fault" symbol flashes if a serious fault has

occurred. Call your qualified contractor.

OPERATION

Settings

6 | VRC-W 400 (E) www.stiebel-eltron.com

4.3 Selecting the fan stage

From the home screen, you can use the Touch-Wheel to select fan

stages 0, 1 and 2. The set value is accepted without you having to

press a button to conﬁrm it.

You cannot activate intensive ventilation with the Touch-Wheel.

To switch on intensive ventilation, press the "intensive ventilation"

button for approx. one second. When intensive ventilation is acti-

vated, the "intensive ventilation" indicator illuminates.

You can activate intensive ventilation with an external pushbutton

or with the "intensive ventilation" button. You can only deactivate

intensive ventilation with the "intensive ventilation" button.

4.4 Activating time programs

The "time" symbol indicates that time programs are activated.

If the time programs are not activated, turn the Touch-Wheel

clockwise to switch from the home screen. After fan stage2, the

fan stage set in the time program appears along with the "time"

symbol.

Note

If you switch the appliance to time program operation,

time programs must be entered in the "prog" menu. Oth-

erwise the appliance continues to run without a time limit

in set fan stage 2.

Enter the time program settings in the menu.

At times where there is no time program deﬁned, the appliance

runs in set fan stage 2.

4.5 Menu

Display Description

 P1 - Pxx Parameter

 I1 - Ixx Actual values

 Pro Programs

 Cod Entry of the code for unlocking protected parameters and actual

values

f To access the parameters, press the "MENU" button.

The "HOME" button takes you to the standard display. If you have

not changed any settings for a while, the appliance automatically

switches back to the standard display.

4.5.1 Parameter

Description Options Unit Min. Max. Stand-

ard

P1 Set room temperature °C 5 28 20

P2

This parameter defines

the runtime for inten-

sive ventilation. After

this time has expired,

the appliance returns

to the previously appli-

cable fan stage.

Min.

1

240

30

P3 Bypass mode 0 | 1 | 2 | 3 2

P4 Reset filter 1 | 0

P28 Enable fan On | OFF On

P80 Day 1 7

P81 Time 00:00 23:59

P82 Level of lighting 2 10 10

Description Options Unit Min. Max. Stand-

ard

P83 Mode of backlighting Auto | On | OFF Auto

P84 Illumination duration s 10 500 60

P85

Lower standard display

OFF | Time | Set

room temperature |

Extract air temp. |

Extract air humidity

OFF

In order to set the parameter, you must ﬁrst make it editable by

pressing the "OK" button. Then you can change the value with

the Touch-Wheel. If you do not press the "OK" button to make the

parameter editable, activating the Touch-Wheel causes the next

parameter to be displayed.

Press the "OK" button to save the set value for a parameter. If you

do not conﬁrm the parameter change with the "OK" button, your

change will be lost.

P1: Set room temperature

Use this parameter to set the outside temperature from which

the bypass damper ensures that outdoor air bypasses the heat

exchanger and ﬂows directly into the building.

P3: Bypass mode

Effect

0 The bypass is permanently disabled. Air flows through the heat exchang-

er.

1 The bypass is active. The air flow bypasses the heat exchanger.

2 The bypass operates with summer day detection. This option is set in the

delivered condition.

3 The bypass operates subject to the extract air temperature.

Note

The qualiﬁed contractor can set the parameters men-

tioned in the description of this parameter.

P24: Bypass enable temperature

P25: Bypass blocking temperature

P26: Bypass hysteresis

P27: Temperature differential for enabling the bypass

P3 = 2 : Bypass with summer day detection

For the bypass to be activated, the following condition must apply

for 60 minutes: Outdoor air temperature > Set room temperature

+ P27

If all the following conditions are met, the appliance switches to

bypass mode.

- Outdoor air temperature < Extract air temp. - P26

- Extract air temp. > Set room temperature

If one of the following conditions is met, the appliance terminates

bypass mode.

- Outdoor air temperature < P25

- Outdoor air temperature > Extract air temp. - P26

- Extract air temp. < Set room temperature

OPERATION

Settings

www.stiebel-eltron.com VRC-W 400 (E) | 7

ENGLISH

P3 = 3 : Bypass subject to extract air temperature

For the bypass to be activated, the following condition must apply

for 60 minutes: Extract air temp. > Set room temperature + P27

This delayed enabling prevents cooling down in spring and au-

tumn.

If all the following conditions are met, the appliance switches to

bypass mode.

- Outdoor air temperature < Extract air temp. - P26

- Extract air temp. > Set room temperature

If one of the following conditions is met, the appliance terminates

bypass mode.

- Outdoor air temperature < P25

- Outdoor air temperature > Extract air temp. - P26

- Extract air temp. < Set room temperature

P4: Reset ﬁlter

f Set this parameter to 1 after changing the ﬁlters. The appli-

ance resets the ﬁlter runtime to 0. This parameter is auto-

matically reset to 0.

P28 : Enable fan

You can switch off the fans at any time via the programming unit

menu, e.g. to deactivate ventilation if there is a ﬁre.

Effect

OFF The fans are deactivated. "OFF" and the fan icon flash on the display.

On The fans are enabled.

P80: Day

1 Monday

2 Tuesday

3 Wednesday

4 Thursday

5 Friday

6 Saturday

7 Sunday

P83: Mode of backlighting

Effect

On Backlighting switched on

OFF Backlighting switched off

Auto

If no user action occurs within the time selected in the illumination

duration parameter, the display backlighting switches off and the

standard display appears.

P84: Illumination duration

If no user action occurs within the time selected in the illumination

duration parameter, the display backlighting switches off and the

standard display appears.

P85: Lower standard display

Use this parameter to deﬁne what is displayed in the lower section

of the standard display. If the appliance detects a fault, the fault is

indicated in the lower section of the standard display.

4.5.2 Actual values

Display Description Unit

 I1 Bypass damper status

 I2 Extract air temp. °C

 I3 Relative humidity of extract air %

 I4 Filter service life h

 I5 Appliance software version

 I6 Unit software patch

 I7 Terminal device serial number

 I8 Programming unit software version

 I70-79 Fault memory

Faults detected by the appliance are stored in actual values I70 to

I79. The latest fault is stored in I70; the oldest in I79. If no faults

are entered, dashes are shown. The latest fault is also shown in

the lower section of the standard display. Possible faults are listed

for qualiﬁed contractors in the "Troubleshooting" chapter.

4.5.3 Programs

Pro

The appliance offers the option to set 21 time programs. Switch

between the time programs using the Touch-Wheel. Press the "OK"

button to switch to setting a time program.

Time pro-

gram x

x.1 x.2 x.3 x.4

Day or group of

days

Fan stage Start time Stop time

 1

 2

 3

 4

 5

 6

 7

 8

 9

 10

 11

 12

 13

 14

 15

 16

 17

 18

 19

 20

 21

Setting a time program begins with selecting a day of the week or

a group of days. Press "OK". Set the day using the Touch-Wheel.

Conﬁrm with the "OK" button.

OPERATION

Maintenance, cleaning and care

8 | VRC-W 400 (E) www.stiebel-eltron.com

Use the Touch-Wheel to switch to setting the fan stage. Press

"OK". Set the fan stage in which the appliance runs when the

time program takes effect using the Touch-Wheel. Conﬁrm with

the "OK" button.

Note

You cannot switch on fan stage3 with time programs.

Use the Touch-Wheel to switch to setting the start time. Press

"OK". Set the start time of the respective time program using the

Touch-Wheel. Conﬁrm with the "OK" button.

Use the Touch-Wheel to switch to setting the stop time. Press "OK".

Set the stop time of the respective time program using the Touch-

Wheel. Conﬁrm with the "OK" button. To delete a time program,

go to the menu item where the day or group of days is selected for

the respective time program. Turn the Touch-Wheel anti-clockwise

until the day disappears and dashes appear in the lower section

of the display.

Note

In the case of overlapping time programs, the program

with the highest number takes priority.

Note

At times where there is no time program deﬁned, the

appliance runs in set fan stage 2.

Example

Time scale Stage

Monday - Friday

06:00 - 22:00 2

22:00 - 06:00 1

Saturday , Sunday

07:00 - 23:00 2

23:00 - 07:00 1

x x.1 x.2 x.3 x.4

Day or group of days Fan stage Start

time

Stop time

 1 1/2/3/4/5 1 22:00 00:00

 2 1/2/3/4/5 1 00:00 06:00

 3 6/7 1 23:00 00:00

 4 6/7 1 00:00 07:00

4.5.4 Code

Cod

You can use this menu item to enable actual values and parame-

ters, which are reserved for qualiﬁed contractors.

Effect

A0 The only parameters displayed are those that have been released for the

appliance user and can therefore be accessed without a code.

A1 Parameters for qualified contractors

A2 Parameters for service department

A1 or A2 is shown on the display when you enter the correct

four-digit code.

If you switch to the actual values or parameters, you see the en-

abled parameters.

Note

After entering the code, switch to the menu by pressing

the "MENU" button. If you ﬁrst switch to the standard

display by pressing the "HOME" button, the parameter

block is reactivated.

4.6 Switching off the appliance

D0000040280

The appliance has no ON/OFF switch. Disconnect the power supply

by pulling the power plug from its socket.

5. Maintenance, cleaning and care

Maintenance by the user is limited to ﬁlter inspection and replace-

ment required at certain intervals.

5.1 Replacement ﬁlters

Product

name

Part

number

Description

FMS G4-10 180 234147 Coarse particle filter mat ISO Coarse > 60 % (G4)

FMK M5-2 180 234148 Fine filter ePM

10

≥ 50 % (M5)

FMK F7-2 180 234208 Fine filter ePM

1

≥ 50 % (F7)

5.2 Filter inspection and replacement

!

Material losses

Never operate the appliance without ﬁlters.

f Inspect the ﬁlters for the ﬁrst time three months after com-

missioning the appliance.

When the total fan runtimes reach the "Filter change interval"

value, which can be set by the qualiﬁed contractor, the program-

ming unit displays the "Filter" symbol.

The qualiﬁed contractor can lengthen or shorten the interval for

inspecting ﬁlters depending on the level of contamination.

If the "ﬁlter" symbol illuminates, check the ﬁlters. Change the

ﬁlters if the surface is covered completely in dirt or the ﬁlter is

discoloured throughout.

OPERATION

Troubleshooting

www.stiebel-eltron.com VRC-W 400 (E) | 9

ENGLISH

Change the ﬁlters at least every 12 months.

Filter inspection

f Pull the mains plug out of the socket.

3.

2.

1.

D0000040362

1

2

3

4

5

1 Extract air ﬁlter

2 Outdoor air ﬁlter

3 Knurled screw for securing the ﬁlter drawer

4 Fascia

5 Locking tabs

The fascia is fastened to the appliance with locking tabs.

f To disengage the locking tabs, press the grip areas on the

fascia sides.

f Remove the fascia from the appliance.

f Undo the knurled screws securing the ﬁlter drawer.

f Pull the ﬁlter drawer forwards to remove it from the

appliance.

f If necessary, place one or more new ﬁlters in the ﬁlter

drawer. Ensure that the ﬁlters are installed in the intended

position. Air ﬂows through the ﬁlters from top to bottom. The

ﬂow direction is indicated with an arrow on the ﬁlter drawer

fascia. The outdoor air ﬁlter is marked with an arrow. Install

the outdoor air ﬁlter with the arrow pointing in the ﬂow

direction. The extract air ﬁlter is imprinted with the words

"Clean air side", which must be at the bottom.

!

Material losses

Operate the appliance with at least the recommended

ﬁlter class. Ensure that ﬁlters are ﬁtted accurately so they

can function properly.

f Push the ﬁlter drawer into the appliance.

f Secure the ﬁlter drawer with the knurled screws.

f Fit the fascia.

f Plug the mains plug into a standard socket.

f Carry out a ﬁlter reset by setting parameter P4 to 1. The

"ﬁlter" symbol disappears. The appliance resets the ﬁlter

runtime to 0.

f Make a note of the ﬁlter change date.

Note

There is a label for each ﬁlter on the front panel.

f Once you have performed a ﬁlter change, erase the

previously entered dates in the "Last" and "Next"

columns.

f Enter today's date in the "Last" column.

f Enter the date for the next ﬁlter change in the "Next"

column. For the period between "Last" and "Next",

use the value set by the qualiﬁed contractor in pa-

rameter P19.

f Order new ﬁlters in good time or purchase a ﬁlter

subscription.

Note

If other ﬁlters are installed in the system, e.g. ﬁlters in the

extract air vents or a ﬁlter box, also perform the inspec-

tion there and change the ﬁlter(s) if necessary.

6. Troubleshooting

Faults detected by the appliance are stored in actual values I70

to I79. The latest fault is also shown in the lower section of the

standard display.

If you cannot remedy the fault, contact your qualiﬁed contractor.

To facilitate and speed up your request, provide the number from

the type plate (000000-0000-000000).

INSTALLATION

Safety

10 | VRC-W 400 (E) www.stiebel-eltron.com

INSTALLATION

7. Safety

Only a qualiﬁed contractor should carry out installation, commis-

sioning, maintenance and repair of the appliance.

7.1 General safety instructions

We guarantee trouble-free function and operational reliability only

if original accessories and spare parts intended for the appliance

are used.

WARNING Electrocution

Do not reach into the interior of the appliance through

the "Outdoor air" connection when the power supply is

switched on.

7.2 Instructions, standards and regulations

Note

Observe all applicable national and regional regulations

and instructions.

!

WARNING Injury

In connection with the ﬁre prevention regulations con-

cerning the installation of ventilation systems, observe

all country-speciﬁc regulations and requirements. In

Germany, these are particularly the building regulation

guideline on ﬁre prevention requirements of ventilation

systems in its applicable version.

7.3 Operation of the appliance in buildings with

combustion equipment

The term "combustion equipment" used below includes, for exam-

ple, tiled stoves, ﬁreplaces and equipment with gas combustion.

!

WARNING Injury

Ventilation units can generate negative pressure in the

dwelling. If combustion equipment is operating at the

same time, combustion exhaust gases can penetrate the

room where the combustion equipment is installed. It is

therefore important to observe a number of points for

simultaneous operation of a ventilation unit and com-

bustion equipment.

The engineering, installation and operation of the ventilation unit

and combustion equipment must be carried out in accordance with

national and regional regulations.

7.3.1 Planning safety measures

Together with the relevant authorities, engineers plan the safety

measures that are required for simultaneous operation of a ven-

tilation unit and combustion equipment.

Alternate operation

Alternate operation means that, when the combustion equipment

is started, the mechanical ventilation system is switched off and/

or cannot be started. Alternate operation must be ensured by

appropriate measures, e.g. automatically enforced shutdown of

the ventilation unit.

Simultaneous operation

For simultaneous operation of combustion equipment and a me-

chanical ventilation system, we recommend choosing approved

room sealed combustion equipment (in Germany, with DIBt ap-

proval).

If open ﬂue combustion equipment is operated in the dwelling

at the same time as a ventilation unit, combustion exhaust gases

must be prevented from penetrating the home as a result of pos-

sible negative pressure in the room.

The ventilation unit may only be operated in combination with

intrinsically safe combustion equipment. This combustion equip-

ment has, for example, a draught hood or an exhaust gas monitor

and is permitted to be operated in conjunction with ventilation

units. Alternatively, external, tested safety equipment can be con-

nected to monitor the operation of the combustion equipment.

For example, you can install differential pressure monitoring to

monitor the chimney draught and to switch off the ventilation unit

in the event of a fault.

The equipment for differential pressure monitoring must fulﬁl the

following requirements:

- Monitoring of the differential pressure between the connec-

tion piece to the chimney and the room where the combus-

tion equipment is installed

- Possibility of matching the shutdown value for the differential

pressure to the minimum draught requirement for the com-

bustion equipment

- Floating contact to switch off ventilation

- Optional connection of a temperature capturing device so

that differential pressure monitoring is only enabled when

the combustion equipment is in operation and so that un-

wanted shutdowns due to environmental inﬂuences can be

avoided

Note

Differential pressure switches that use the pressure

differential between the outdoor air pressure and the

pressure in the room where the combustion equipment

is sited as a response criterion are not suitable.

Note

We recommend installing and regularly maintaining a

carbon monoxide detector in accordance with EN50291

for operation of any combustion equipment.

INSTALLATION

Appliance description

www.stiebel-eltron.com VRC-W 400 (E) | 11

ENGLISH

7.3.2 Commissioning

When commissioning the ventilation unit, it is important to check

and document in the commissioning log that combustion exhaust

gases are not penetrating the dwelling in a quantity that is harmful

to health.

Commissioning in Germany

Acceptance is carried out by the local ﬂue gas inspector.

Commissioning outside Germany

Acceptance must be carried out by a specialist. In case of doubt,

you must involve an independent expert in the acceptance pro-

cedure.

7.3.3 Maintenance

Regular maintenance of the combustion equipment is prescribed.

Maintenance includes checking the exhaust gas extraction system,

the free pipe cross-sections and the safety equipment. The rele-

vant qualiﬁed contractor responsible must prove that there is a

sufﬁcient ﬂow of combustion air.

7.4 Operating the appliance in passive houses

If operating the appliance in a passive house, the factory-ﬁtted

outdoor air ﬁlter must be replaced. See chapter "Appliance de-

scription/ Accessories".

8. Appliance description

8.1 Standard delivery

The following are delivered with the appliance:

- Wall mounting bracket

- 2 star grips as spacers for the rear of the appliance

- Condensate drain hose, hose clip, mounting bend

- 4twin connectors, nominal diameter160

8.2 Accessories

- Programming unit

- Silencer attachment ( LWF SDA 180/280 )

- For installation of the equipment in passive houses: Outdoor

air ﬁlter ePM

1

≥ 50 % (F7)

You can obtain ventilation pipes, extract air and supply air vents

and similar accessories from us.

9. Preparation

9.1 Storage

!

Material losses

Never store the appliance in dusty places.

9.2 Installation site

!

Material losses

Never install the appliance outdoors.

!

Material losses

Check whether the wall can bear the weight of the appli-

ance. A plaster board or metal framed wall is inadequate.

Additional measures such as a double skin or additional

supports would be needed in such cases.

- Ensure the appliance is level after installation.

- The installation room must have an adequate condensate

drain with siphon.

- The installation room must be free from the risk of frost.

9.2.1 Minimum clearances

If you wish to install the silencer attachment, which is available

as an accessory, observe the minimum clearances it requires.

≥400

≥700

≥400

≥300

D0000040354

INSTALLATION

Installation

12 | VRC-W 400 (E) www.stiebel-eltron.com

Installation drawing with silencer attachment

1486

1340

147

379

D0000085684

≥100

≥700

≥400

D0000085683

9.3 Transport

!

Material losses

If possible, transport the appliance to the installation lo-

cation in its original packaging.

If the appliance is transported without packaging and

without using a pallet, e.g. to carry it up or down stairs,

its outer casing may be damaged.

To transport the appliance without packaging, ﬁrst re-

move the front panel of the appliance. See chapter "In-

stallation/ Removing the front panel".

!

Material losses

Never use the air connections as handles for carrying

the appliance.

10. Installation

10.1 Removing the front panel

Remove the front panel before removing the appliance from the

pallet, to avoid damaging the appliance.

D0000040363

1

2

1 Fascia

2 Front panel ﬁxing screws

The fascia is fastened to the appliance with locking tabs.

f To disengage the locking tabs, press the grip areas on the

fascia sides.

f Remove the fascia from the appliance.

f Undo both screws securing the front panel at the top of the

appliance.

f Carefully push the front panel upwards by a small amount to

release it from the hooks on which it is engaged.

D0000040364

1

1 Plug on cable from programming unit to appliance

f Carefully raise the front panel by a small amount on the

right-hand side.

INSTALLATION

Installation

www.stiebel-eltron.com VRC-W 400 (E) | 13

ENGLISH

f On the appliance, pull out the plug connecting the program-

ming unit with the appliance.

10.2 Mounting the appliance

!

Material losses

If the unit is not mounted horizontally, condensate cannot

drain properly. Condensate escaping in an uncontrolled

manner can damage the ﬂoor or items in the vicinity of

the unit.

!

Material losses

f Check whether the wall can bear the weight of the

appliance.

f Use appropriate rawl plugs and screws suitable for

the wall structure to attach the rail.

f Remove the wall mounting bracket from the appliance.

D0000040851

f Secure the wall mounting bracket to the wall with four

screws. The text "TOP" must be at the top. The wall mounting

bracket must be horizontal.

f If necessary, screw the star grips included in the standard

delivery into the back of the appliance at the bottom to act as

spacers.

f Fit the appliance onto the hooks of the wall mounting

bracket.

f If the appliance is not hanging horizontally, screw the previ-

ously ﬁtted star grips acting as spacers in or out by a small

amount.

10.3 Connecting the condensate drain hose

!

Material losses

To ensure that condensate drains correctly, always lay

the condensate drain hose without any kinks. Lay the

condensate drain hose with a fall of at least 10%. Ensure

the appliance is level after installation.

The drain pipe may only contain one siphon. The con-

densate must be able to drain freely downstream of the

siphon. The condensate must drain away via the domestic

sewer system. The pipes must not rise in the domestic

sewer system downstream of the siphon. The condensate

drain must be free from the risk of frost.

!

Material losses

A ﬂoat switch prevents condensate from reaching live

parts in the unit.

If the condensate drain hose is installed incorrectly, the

ﬂoat switch cannot prevent the uncontrolled leakage of

condensate.

Note

To ensure the unit is airtight, there may be no inter-

ruption in the condensate drain between the unit and

the trap. Use the supplied condensate drain hose and

mounting bend.

The standard delivery includes a condensate drain hose and a

hose clip. Connect the thinner end of the condensate drain hose

to the appliance.

≥80

D0000058970

f Use the mounting bend included in the standard delivery to

install the condensate drain hose in such a way as to create a

siphon with a water trap height of at least 80mm.

f Before connecting the condensate drain hose to the appli-

ance, pour water into the siphon.

D0000058969

1

1 Hose clip

f Slide the hose clip onto the condensate drain hose far

enough to be able to push the hose onto the condensate

drain connector without squeezing the hose clip.

f Push the condensate drain hose onto the condensate drain

connector.

f Push the hose clip towards the appliance so that it secures

the hose on the condensate drain connector.

INSTALLATION

Installation

14 | VRC-W 400 (E) www.stiebel-eltron.com

10.4 Air ducts

!

Material losses

Never link cooker hoods to the ventilation system.

!

Material losses

During installation, ensure that no metal swarf enters

the pipework. However, should this occur, remove this

debris, otherwise the fans may be damaged.

Install the air ducts using materials that can be obtained from us

or with commercially available folded spiral-seam tubes.

10.4.1 Insulation against condensation

!

Material losses

When warm air meets cold surfaces, condensation can

result.

f For outdoor air and exhaust air ducts, use vapour

proof thermally insulated pipes.

f If the supply and extract air ducts are routed

through unheated rooms, insulate these ducts as

well.

10.4.2 Connecting air ducts to the appliance

You can connect air ducts with two different diameters to the

appliance.

Diameter DN160

D0000062517

1

2

1 Twin connector

2 Air duct

f Push one of the twin connectors included in the standard de-

livery into the air connection.

f Push the air duct onto the twin connector.

3x

1

D0000062518

1 Self-tapping screw

f Use no more than 3 screws to secure the twin connector to

the air connection of the appliance.

f Secure the air duct to the twin connector with no more than

3 screws.

Diameter DN180

D0000062519

f Push the air duct over the air connector.

3x

1

D0000062520

1 Self-tapping screw

f Use no more than 3 screws to secure the air duct to the air

connection of the appliance.

D0000062521

1

1 Aluminium sealing tape

f Seal the transition from the air connection to the air duct

with aluminium sealing tape.

10.4.3 External wall ducts

Install the outdoor air intake into the building at a location where

contamination (dust, soot, odours, ﬂue gas, exhaust air) is as low

as possible.

When installing external wall ducts, prevent any short circuit be-

tween the air intake and the air discharge.

INSTALLATION

Installation

www.stiebel-eltron.com VRC-W 400 (E) | 15

ENGLISH

10.4.4 Silencers

f Install a silencer in both the supply air duct and the extract

air duct. Install these silencers as close as possible to the ap-

pliance, so that noise is suppressed at an early stage.

We recommend installing additional silencers if required to avoid

sound transmission.

If a room with a high noise level needs to be ventilated, install

additional silencers upstream of this room to reduce sound trans-

mission to the neighbouring rooms.

Aspects such as carried voices and impact sound must also be

taken into consideration in the case of ducts embedded in con-

crete. Carried voices should be avoided by designing the duct with

separate branches to the vents. If necessary, insulate the supply air

ducts, e.g. if they are mounted outside the insulated wall panel.

10.4.5 Overﬂow apertures

Living rooms and bedrooms are only supplied with air. Air is only

extracted from rooms where odours and moisture are generated.

Ensure an unimpeded overﬂow and consequently air balancing.

Install ventilation grilles in internal doors or walls, or enlarge the

air gap beneath the door to ≥8mm.

10.4.6 Cleaning apertures

f Fit cleaning apertures when installing the air ducts, so

that the air ducts can be inspected and cleaned at regular

intervals.

10.4.7 Supply and extract air vents

Supply and extract air vents for the living space are available for

wall or ceiling mounting.

When venting the kitchen, ensure that the extract air vent is ﬁtted

as far as possible from the cooker.

10.5 Fitting the front panel

f Push the plug on the cable leading to the programming unit

into the appliance.

f Hook the front panel into the hooks provided at the front of

the appliance.

f At the upper edge of the front panel, screw in the two screws

for securing the front panel to the appliance.

f Fit the fascia.

10.6 Electrical connection

WARNING Electrocution

Carry out all electrical connection and installation work

in accordance with national and regional regulations.

Use the plug on the power cable to connect the appliance to a

standard socket.

Take the power consumption of the preheating coil into consid-

eration.

10.6.1 Safety equipment for stove/ﬁreplace operation

f Install the safety equipment in such a way that it interrupts

the appliance power supply when required.

10.6.2 Connections in the control panel ( Safety extra low

voltage )

D0000065179

f Undo the four screws from the control panel cover.

Note

After completing your work, screw the cover back onto

the control panel.

D0000065180

f Carefully lift up the control panel cover. The terminal block,

from which cables lead into the appliance, is suspended from

the underside of the cover.

INSTALLATION

Commissioning

16 | VRC-W 400 (E) www.stiebel-eltron.com

Terminal Safety extra low voltage

1 I²C bus SCL External programming unit

2 SCL

3 GND External programming unit

4 GND

5 +5VDC External programming unit

6 +5VDC

7 SDA External programming unit

8 SDA

9 Not assigned Floating

10

11

12

13 Intensive ventilation switch-

ing contact

GND 0.5mA max.

14 +5 V

15 Not assigned Floating

16

17 Not assigned Floating

To connect an electrical cable in the control panel:

f Open an "entry for electrical cables" at the knock-out.

f Use an M12 cable ﬁtting to seal the "entry for electrical

cables".

Intensive ventilation switching contact

You can connect a ﬂoating switching contact, the actuation of

which switches the appliance to intensive ventilation. You can set

the runtime for intensive ventilation in parameter P2. After this

time has expired, the appliance returns to the previously appli-

cable fan stage.

f Connect the external pushbutton to terminals 13/14.

External programming unit

The programming unit is connected with an I²C bus.

11. Commissioning

!

WARNING Injury

If the unit is switched on without the air ducts connected

and someone reaches through the air connectors into the

unit, there is a risk of injury.

Do not commission the unit until the air ducts are ﬁrmly

connected to it.

!

Material losses

Never operate the appliance without ﬁlters.

!

Material losses

Never operate the ventilation system if there are high lev-

els of dust inside the building or outside in the immediate

vicinity, as this could block the ﬁlter. Dust is created by

cutting tiles or working with plasterboard, for example.

11.1 Initial start-up

f To access the parameters, press the “MENU” button.

Display Description

 P1 - Pxx Parameter

 I1 - Ixx Actual values

 Pro Programs

 Cod Entry of the code for unlocking protected parameters and actual

values

f Enter 1000 to enable actual values and parameters which are

reserved for qualiﬁed contractors.

Enable fan

The fans are deactivated in the delivered condition.

f P28 : Set the parameter to "On".

Setting air ﬂow rates

f Use parameters P6 to P9 to set the air ﬂow rates for the fan

stages.

Date

f Set the current day of the week.

P80 1 Monday

2 Tuesday

3 Wednesday

4 Thursday

5 Friday

6 Saturday

7 Sunday

Time

f Set the current time.

P81 00:00 - 23:59

11.2 Recommissioning

f Check whether ﬁlters are ﬁtted in the appliance. Never oper-

ate the appliance without ﬁlters.

f Check whether the condensate drain hose is damaged or

kinked.

INSTALLATION

Settings

www.stiebel-eltron.com VRC-W 400 (E) | 17

ENGLISH

12. Settings

When you enter a four-digit code, additional actual values become

visible, which were hidden beforehand.

12.1 Parameter

P28: Delivered condition OFF

VRC-W 400 VRC-W 400 E

Description Code Unit Min. Max. Options Stand-

ard

Min. Max. Options Stand-

ard

P1 Set room temperature A0 °C 5 28 20 5 28 20

P2 Intensive ventilation runtime A0 Min. 1 240 30 1 240 30

P3 Bypass mode A0 0 | 1 | 2 | 3 2 0 | 1 | 2 | 3 2

P4 Reset filter A0 0| 1 - 0| 1 -

P6 Flow rate, stage0 A1 m³/h 40 150 60 40 150 60

P7 Flow rate, stage 1 A1 m³/h 60 300 140 60 300 140

P8 Flow rate, stage 2 A1 m³/h 60 400 200 60 400 200

P9 Flow rate, stage 3 A1 m³/h 60 400 260 60 400 260

P14 Supply air flow rate offset A1 -100 100 0 -100 100 0

P15 Humidity protection interval A1 h 1 24 1 1 24 1

P16 Start-up time for humidity measurement A1 min 5 15 5 5 15 5

P17 Extract air humidity limit A1 % 5 95 65 5 95 65

P18 Frost protection temperature A1 °C -10.0 10.0 4.0 -10.0 10.0 4.0

P19 Filter change interval A1 d 1 365 90 1 365 90

P22 Enable preheater A1 0 | 1 1 0 | 1 1

P23 Frost protection mode A1 0 | 2 2 0 | 2 2

P24 Bypass enable temperature A1 °C 5.0 15.0 10.0 5.0 15.0 10.0

P25 Bypass blocking temperature A1 °C 5.0 15.0 8.0 5.0 15.0 8.0

P26 Bypass hysteresis A1 K 0.0 5.0 2.0 0.0 5.0 2.0

P27 Temperature differential for enabling the bypass A1 °C 0.0 5.0 2.0 0.0 5.0 2.0

P28 Enable fan A0 On | OFF On On | OFF On

P29 Appliance type A1 9 10

P30 Temperature for enabling frost protection A2 °C -10.0 10.0 -3.0 -10.0 10.0 -3.0

P31 Enabling of humidity-dependent flow rate control A1 0| 1 0 0| 1 1

P32 Enable outdoor air condensate prevention A2 0 | 1 0 0 | 1 0

P33 Temperature offset for condensate prevention A2 K -5.0 5.0 0.0 -5.0 5.0 0.0

P35 Bypass function cooling/heating A2 1 | 2 | 3 1 1 | 2 | 3 1

P70 Delete fault list A1 0| 1 - 0| 1 -

P80 Day A0 1 7 1 7

P81 Time A0 00:00 23:59 00:00 23:59

P82 Level of lighting A0 2 10 10 2 10 10

P83 Mode of backlighting A0 Auto | On | OFF Auto Auto | On | OFF Auto

P84 Illumination duration A0 s 10 500 60 10 500 60

P85

Lower standard display

A0

OFF | Time | Set room

temperature | Extract

air temp. | Extract air

humidity

OFF

OFF | Time | Set room

temperature | Extract

air temp. | Extract air

humidity

OFF

INSTALLATION

Settings

18 | VRC-W 400 (E) www.stiebel-eltron.com

P14 : Supply air ﬂow rate offset

Use this parameter to adjust the supply air ﬂow rate during com-

missioning. The offset refers to standard ventilation and is con-

verted internally as a percentage for the other fan stages.

Example

- Nominal ﬂow rate (stage2): 180 m³/h

- Offset : 45 m³/h

Stage

Set flow

rate

Off-

set

Set flow

rate +

Offset

Offset fac-

tor

Internal set flow

rate = Set flow rate

* Offset factor

0 50 50*1.25 = 62

1 130 130*1.25 = 162

2 180 45 180+45 = 225 225/180 = 1.25 180*1.25 = 225

3 235 235*1.25 = 294

P15 : Humidity protection interval

If you set fan stage 0, the appliance switches to a 24 hour dormant

phase. The humidity protection control unit only starts after this.

The appliance measures the humidity of the extract air for the time

set in P16. The appliance compares the last measured value with

the limit value set in P17. If the limit value is exceeded, the appli-

ance starts to ventilate. If the limit is undershot again, the appli-

ance terminates ventilation. At this point, the humidity protection

interval restarts, at the end of which the moisture is measured.

P16 : Start-up time for humidity measurement

The appliance measures the humidity of the extract air for the time

set in P16. The appliance compares the last measured value with

the limit value set in P17.

P22 : Enable preheater

Effect

0 The internal preheater is completely deactivated.

1

The internal preheater is activated. In order to keep the heat exchanger

free from ice, the preheater ensures a minimum supply air temperature

with reference to the frost protection temperature adjustable in param-

eter P18.

While this parameter is being displayed or adjusted, the "frost

protection" symbol is shown on the display.

P23 : Frost protection mode

Effect

0 At this setting, the appliance operates solely in frost protection mode. The

preheating coil control only measures the outside temperature.

2

At this setting, the appliance operates in comfort mode. In addition to the

outside temperature, the supply air temperature is also measured. The

preheating coil is controlled to ensure that the supply air temperature

does not fall below the 16.5°C specified in the passive house criteria.

P24 : Bypass enable temperature

To enable checking of the other parameters for the bypass, the

outdoor air temperature must be no less than the value set in

this parameter.

P25 : Bypass blocking temperature

If the outdoor air temperature falls below this blocking tempera-

ture, the bypass is deactivated.

P26 : Bypass hysteresis

To make cooling possible, the outdoor air temperature must be

lower than the extract air temperature by the value set in this

parameter.

To make heating possible, the outdoor air temperature must be

higher than the extract air temperature by the value set in this

parameter.

P27 : Temperature differential for enabling the

bypass

Use this parameter to deﬁne the temperature differential that must

be exceeded for the bypass to be enabled. For the bypass to be

enabled, the following condition must be met for 60 minutes.

P3 = 2 : Outdoor air temperature > Set room temperature + P27

P3 = 3 : Extract air temp. > Set room temperature + P27

P29 : Appliance type

This parameter is set at the factory. The parameter can only be set

after the controller assembly has been replaced.

P30 : Temperature for enabling frost protection

The unit only activates frost protection heating if the outdoor air

temperature drops to the value that can be set in this parameter.

P31 : Enabling of humidity-dependent ﬂow rate

control

With humidity-dependent ﬂow rate control, the air ﬂow rate is

increased or decreased depending on the humidity level.

Effect

0 inactive

1 active

P32 : Enable outdoor air condensate prevention

The condensate prevention function is intended for units without

an enthalpy heat exchangers in areas with a subtropical climate.

If the unit is in ventilation mode and this parameter has the value

1, the unit checks the following conditions:

- Outdoor air temperature > Extract air temp.

- Extract air temp. + P33 < Outdoor air dew point

If both conditions are met, the unit switches the fans off. After

a shutdown, the unit switches on the fans cyclically and checks

whether the conditions are still valid or whether ventilation mode

can be resumed.

Interval between measurements min 60

Duration of measurement min 5

INSTALLATION

Appliance shutdown

www.stiebel-eltron.com VRC-W 400 (E) | 19

ENGLISH

P33 : Temperature offset for condensate prevention

This parameter is used to vary the shutdown point for condensate

prevention. This allows the fans to be switched off 2K before the

dew point temperature is reached, for example.

P35 : Bypass function cooling/heating

f Set the operating mode for the bypass function.

Effect

1 Cooling/heating

2 Cooling

3 Heating

P70 : Delete fault list

To delete the fault list, set this parameter to 1. Press the "OK"

button to conﬁrm. Afterwards, 0 is displayed again and the fault

list is deleted.

12.2 Actual values

Display Description Unit

I1 Bypass damper status

I2 Extract air temperature °C

I3 Relative humidity of extract air %

I4 Filter service life h

I5 Appliance software version

I6 Unit software patch

I7 Terminal device serial number

I8 Programming unit software version

I9 Outdoor air temperature °C

I10 Supply air temperature °C

I11 Exhaust air temperature °C

I12 Relative humidity of outdoor air %

I13 Extract air dew point °C

I14 Outdoor air dew point °C

I15 Supply air fan control level %

I16 Calculated supply air flow rate m³/h

I17 Exhaust air fan control level %

I18 Calculated exhaust air flow rate m³/h

I19 Percentage output of internal preheating %

I20 Ventilation unit operating time d

I21 Fan operating time d

I22 Extract air pressure differential Pa

I23 Fan speed, supply air fan rpm

I24 Fan speed, exhaust air fan rpm

I70-79 Fault

12.3 Code

Cod

Enter 1000 to enable actual values and parameters which are re-

served for qualiﬁed contractors. "A1" is shown on the display when

this is entered correctly.

13. Appliance shutdown

We recommend running the appliance in fan stage1, even during

prolonged absence.

!

Material losses

If you interrupt the power supply to the appliance, check

that humidity protection is ensured for the building.

If the appliance needs to be taken out of use for an extended peri-

od, disconnect it from the power supply by pulling the mains plug.

f Replace the ﬁlters.

14. Maintenance

WARNING Electrocution

Disconnect the appliance from the power supply before

carrying out work inside the appliance.

f Pull the mains plug out of the socket.

Maintenance by the qualiﬁed contractor includes cleaning the

cross-countercurrent heat exchanger and the fans. Subject to runt-

ime, this maintenance work should be carried out every 3years.

f Disconnect the power supply by pulling the power plug from

its socket.

f Remove the front panel (see chapter "Installation/ Removing

the front panel").

f Remove the ﬁlter drawer from the appliance.

D0000065159

f Undo the screws on the inner front panel.

f Remove the inner front panel from the appliance by tilting

the inner front panel forwards and then lifting it out of the

bottom slots.

INSTALLATION

Maintenance

20 | VRC-W 400 (E) www.stiebel-eltron.com

D0000082556

1

1 Wing screw

f To remove the heat exchanger from the appliance, undo the

wing screw, which pushes the support bar against the heat

exchanger from below.

D0000040365

f Carefully remove the heat exchanger from the unit. Avoid

damaging the gaskets in the appliance.

f Use a commercially available vacuum cleaner to remove dust

and other loose dirt particles from the intake and discharge

surfaces.

26�04�15�0047

f If required, clean the heat exchanger with warm water

(max.55 °C) and a commercially available detergent. Do not

use solvents.

f Flush the heat exchanger with water.

Cleaning the fan units

Each fan unit has a rotating eccentric bolt at the bottom. To ensure

that the seals ﬁt correctly on the fan unit, the eccentric bolt raises

the fan unit while pushing it towards the back. Release the eccen-

tric bolt before pulling out the fan unit. Retighten the eccentric

bolt after installing the fan unit.

300°

D0000063652

1

2

1 Eccentric bolt tightened (slot horizontal)

2 Eccentric bolt released

f Use a medium sized screwdriver to turn the eccentric bolt

anti-clockwise by 300°.

f Carefully pull both fan units from the appliance by a small

amount.

D0000040366

4

3

1

2

1 Temperature sensor connection

2 Pressure sensor connection

3 Connection for the fan power cable

4 Connection for the fan control cable

f At the front of the supply air fan, disconnect the 3-core power

cable and the 4-core control cable.

La page charge ...

STIEBEL ELTRON VRC-W 400 (E) Operation Instruction

STIEBEL ELTRON VRC-W 400 (E) Operation Instruction

dans d''autres langues

Documents connexes

Autres documents