RIDGID HD1600D Manuel utilisateur

Part No. SP7037 Printed in Mexico

Wet/Dry Vacs

WET/DRY VAC PARTS

& ACCESSORIES

1-800-474-3443

Call Us 1

st

• Operation

• Warranty

(See back cover)

• Technical Assistance

• Repair Parts

For any questions about:

Please have your Model Number and

Serial Number on hand when calling.

16 U.S. GALLON / 60 Liter

DETACHABLE WET/DRY VAC

ASPIRADORA PARA MOJADO/SECO

DESMONTABLE DE

16 GALONES EE.UU. / 60 Litros

ASPIRATEUR DE LIQUIDES ET

DE POUSSIÈRES AMOVIBLE DE

60 Litres / 16 GALLONS DES É-U

FOR QUESTIONS OR INFORMATION CONTACT US AT

1-800-4-RIDGID (1-800-474-3443)

from the US and Canada

For service parts visit store.ridgid.com/wetdry

OWNER’S MANUAL

MANUAL DEL USUARIO

MODE D’EMPLOI

SAVE THIS MANUAL

FOR FUTURE REFERENCE

GUARDE ESTE MANUAL

PARA REFERENCIA FUTURA

CONSERVER CE MANUEL

POUR RÉFÉRENCE FUTURE

HD16000

D

R

A

I

N

D

R

A

I

N

TABLE OF CONTENTS

*****************

ÍNDICE DE CONTENIDO

*****************

TABLE DES MATIÈRES

*****************

• SAFETY INSTRUCTIONS...........2

• INTRODUCTION ..................4

• ASSEMBLY ......................6

• OPERATION ....................10

• STORAGE ......................15

• MAINTENANCE..................17

• REPAIR PARTS .................20

• INSTRUCCIONES DE SEGURIDAD . 21

• INTRODUCCIÓN .................23

• ENSAMBLAJE ..................25

• FUNCIONAMIENTO ..............29

• ALMACENAMIENTO..............34

• MANTENIMIENTO................36

• PIEZAS DE REPUESTO ...........39

• INSTRUCTIONS RELATIVES

À LA SÉCURITÉ .................40

• INTRODUCTION .................42

• ASSEMBLAGE ..................44

• FONCTIONNEMENT ..............48

• RANGEMENT ...................53

• ENTRETIEN.....................55

• PIÈCES DE RECHANGE ..........60

WARNING:

To reduce the risk of injury,

the user must read and

understand the owner’s

manual before using this

product.

!

ADVERTENCIA:

Para reducir el riesgo de lesiones,

el usuario debe leer y comprender

el manual del usuario antes de

usar este producto.

!

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire

et veiller à bien comprendre le

mode d’emploi avant d’utiliser

ce produit.

!

SP7037-1 HD16000 ESF.indd 1 9/4/19 12:50 PM

2

IMPORTANT SAFETY INSTRUCTIONS

Safety is a combination of using common

sense, staying alert, and knowing how your

Wet/Dry Vacuum Cleaner (“Vac”) works.

Safety Signal Words

DANGER: Indicates a

hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING: Indicates a

hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION: Indicates a

hazardous situation which, if not avoided,

could result in minor or moderate injury or

property damage.

When using your Vac, always follow basic

safety precautions including the following:

WARNING:

- To reduce the risk of fire,

electric shock, or injury:

• Read and understand this manual and

all labels on the Wet/Dry Vac before

operating.

• Use only as described in this manual.

• Do not leave Vac running while

unattended - you may fail to notice

important signs indicating abnormal

operation such as loss of suction, debris/

liquid exiting exhaust, or abnormal

motor noises. Immediately stop using

Vac if you notice these signs.

• Do not leave Vac when plugged in.

Unplug from outlet when not in use and

before servicing.

• Sparks inside the motor can ignite

flammable vapors or dust. To reduce the

risk of fire or explosion, do not use near

combustible liquids, gases, or dusts,

such as gasoline or other fuels, lighter

fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain

dust, aluminum dust, or gun powder.

• Do not vacuum anything that is burning

or smoking, such as cigarettes, matches,

or hot ashes.

• To avoid the risk of self-ignition of drum

debris, empty drum after each use.

Combustible materials, such as rags or

sawdust containing stain or urethane,

can be sources of such overheating.

!

• Do not vacuum drywall dust, cold

fireplace ash, or other fine dusts with

standard filter. These may pass through

the filter and be exhausted back into the

air. Use a fine dust filter instead.

• To reduce the risk of inhaling toxic

vapors, do not vacuum or use near toxic

or hazardous materials.

• To reduce the risk of electric shock,

do not expose to rain or allow liquid to

enter motor compartment. Store indoors.

• This Wet/Dry Vac is not intended for

use by persons (including children) with

reduced physical, sensory, or mental

capabilities, or lack of experience

and knowledge, unless they have

been given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

• Do not allow to be used as a toy. Close

attention is necessary when used by or

near children.

• Do not use with a torn filter or without

filter installed except when vacuuming

liquids as described in this manual.

Dry debris ingested by the impeller may

damage the motor or be exhausted into

the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from

accidental starting, unplug power cord

before changing or cleaning filter.

• Do not unplug by pulling on cord.

To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or

other parts. If your Vac is not working

as it should, has missing parts, has

been dropped, damaged, left outdoors,

or dropped into water, call customer

service.

• Do not pull or carry by cord, use cord

as handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run Vac over cord. Keep cord

away from heated surfaces.

• Do not handle plug, switch, or the Vac

with wet hands.

!

SP7037-1 HD16000 ESF.indd 2 9/4/19 12:50 PM

3

IMPORTANT SAFETY INSTRUCTIONS

• Use only extension cords that are rated

for outdoor use. Extension cords in poor

condition or too small in wire size can

pose fire and shock hazards. To reduce

the risk of these hazards, be sure the

cord is in good condition and that liquid

does not contact the connection. Do not

use an extension cord with conductors

smaller than 1,3 mm

2

(16 AWG).

• This Wet/Dry Vac is double-insulated,

eliminating the need for a separate

grounding system. Use only identical

replacement parts. Read the instructions

for Servicing Double-Insulated Wet/Dry

Vacs before servicing.

• Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep free

of dust, lint, hair or anything that may

reduce air flow.

• Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

• To reduce the risk of falls, use extra

care when cleaning on stairs.

• To reduce the risk of back injury or falls,

do not lift a Vac that is heavy with liquid

or debris. Partially empty by scooping

debris or draining liquid.

• To reduce the risk of personal injury

or damage to Vac, use only RIDGID

recommended accessories.

• When using as a detached blower:

- Direct air discharge only at work area.

- Turn unit off before setting on ground

or releasing grasp from handle.

- Do not set down in liquid; electric

shock could occur.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except

blowing dirt and debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear

safety eyewear. The operation of any

utility Vac or blower can result in foreign

objects being blown into the eyes, which

can result in severe eye damage.

SAVE THIS MANUAL

Observe the following warnings that

appear on the motor housing of your Vac:

DOUBLE INSULATED -

GROUNDING NOT REQUIRED.

WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

CAUTION:

• To reduce the risk of hearing damage,

wear ear protectors when using for

extended hours or in a noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the

relative humidity of the air is low.

Vacuuming fine debris with your Vac can

deposit static charge on the hose or Vac.

To reduce the frequency of static shocks

in your home or when using this Vac, add

moisture to the air with a humidifier.

!

WARNING:

To reduce the risk of electric shock -

do not expose to rain - store indoors.

!

WARNING:

• For your own safety, read and

understand owner’s manual.

• Do not run unattended.

• Do not pick up hot ashes,

coals, flammable, combustible /

self-igniting, toxic, or other hazardous

materials.

• Do not use around explosive

liquids or vapors.

!

• To reduce the risk of being struck by, or

pulled down by, a rolling Vac, block the

casters when using on any uneven or

sloped surface.

SP7037-1 HD16000 ESF.indd 3 9/4/19 12:50 PM

4

This Wet/Dry Vac is intended for house-

hold use. It may be used for vacuuming

wet or dry media and may be used as a

blower.

Getting to Know Your Wet/Dry Vac

Read this Owner’s Manual to familiarize

yourself with the product features and

to understand the specific usage of your

new Vac.

INTRODUCTION

Tug-A-Long Positive Locking Hose

with Dual-Flex - Provides transfer of

vacuum or blowing capability to work site.

Provides the means of attaching extension

wands and nozzles.

Extension Wands - These wands can

be connected together and provide

additional length.

Blower Wand - Attaches directly to the

power assembly and concentrates the air

for blowing applications.

Wet Nozzle - Used for wet pickup on

smooth surfaces to pick up liquid and dry

the surface in one stroke.

Utility Nozzle - General purpose nozzle

for most vacuuming applications.

Car Nozzle - Dry pickup nozzle for car

interiors and most upholstery cleaning.

Familiarize yourself with the accessories included with the Vac. Each accessory may be

used in various ways for vacuuming and blowing debris. Here is a list of the accessories

and their uses.

Detachable Blower

Carry Handle

Detachable Blower

Latch

Casters (4)

Drain

Drum

Latches (2)

Caster Feet/

Storage (4)

Blowing Port

Power Cord

Wrap

Powerhead

Assembly

Inlet Port

Dust

Drum

Power Cord

Blowing

Port

ON/OFF Switch

Accessory

Caddy

D

R

A

I

N

D

R

A

I

N

Hose

Storage

Clip

SP7037-1 HD16000 ESF.indd 4 9/4/19 12:50 PM

Unpacking

5

Carton Contents List

Key Description Qty

A Wet/Dry Vac ...............................1

B Caster Foot w/Storage ................4

C Casters ........................................4

D Pan Head Screws, #10 x 3/4”

(19 mm) ....................................4

E* Qwik Lock™ Filter .......................1

F Tug-A-Long Positive Locking

Hose with Dual-Flex ................. 1

G Extension Wands ........................2

H Blower Wand ...............................1

I Car Nozzle ..................................1

J Utility Nozzle ...............................1

K Wet Nozzle ..................................1

L Accessory Caddy ........................1

M Owner’s Manual ..........................1

* The Filter comes preassembled.

A

E

C

G

J

K

L

I

H

M

D

F

D

R

A

I

N

D

R

A

I

N

B

This Product Requires Assembly.

Check all parts from carton against the

Carton Contents List.

If any parts are damaged or missing, contact

1-800-4-RIDGID (US and Canada) or by

email at [email protected].

INTRODUCTION

SP7037-1 HD16000 ESF.indd 5 9/4/19 12:50 PM

6

ASSEMBLY

NOTE: Remove Powerhead Assembly

from Dust Drum prior to assembly of

Casters and Caster Feet.

1. Turn Dust Drum upside down on floor.

2. Place Caster Foot on floor. Insert the

stem of a Caster into socket of Caster

Foot.

3. Push on the Caster until the Caster ball

end snaps fully into the Socket and the

Caster swivel freely. Repeat for other

three Casters and Caster Feet.

4. Place Caster Foot with Caster over

post on bottom of Dust Drum and press

firmly in place, as shown.

5. Repeat for the other three Caster/

Caster Foot assemblies.

6. Four (4) Screws are available for

optional assembly of the Caster Feet

into the Drum. If desired, locate Four (4)

#10 x 3/4” (19 mm) Pan Head Screws

in loose parts bag. Insert a Screw

through the Hole in the Caster Foot and

into the Dust Drum. Tighten securely.

7. Turn the Dust Drum upright.

Caster/Caster Foot Assembly

Caster

Foot

Caster

Caster Ball

Caster Stem

Optional Hole

for Screw

Placement

Caster Foot

Post Hole

Caster Foot

Post

Dust

Drum

Wet/Dry Vac Assembly

Locking

Tabs (2)

Accessory

Caddy

Dust Drum

ASSEMBLED

Accessory Caddy Installation

1. Place the Two Tabs on the bottom

edge of the Accessory Caddy into the

Two Slots on the rear of the Dust Drum.

2. Pivot the top of the Accessory Caddy

upward until the Two Locking Tabs

engage the upper slots in the Dust

Drum. Press in on the top edge of the

Accessory Caddy until it snaps into

place. Check that the Locking Tabs

are securely locked by pulling outward

on the Accessory Caddy.

SP7037-1 HD16000 ESF.indd 6 9/4/19 12:50 PM

7

ASSEMBLY

2. Install: Press in on the two Latches

located on either side of the Dust Drum

until they snap into place, securing the

Powerhead Assembly to the Dust Drum.

3. Remove: Pull out on the two Latches

and lift Powerhead Assembly from the

Dust Drum. Do not force the Latches to

rotate more than slightly outside Drum

flange.

D

R

A

I

N

Vac Inlet

Latches

(2)

Powerhead

Assembly

Attaching / Removing

Powerhead Assembly to

Dust Drum

1. Place Powerhead Assembly on top of

Dust Drum with the Extended Lip of the

Powerhead Assembly aligned with the

Inlet. Be sure Powerhead Assembly is

fully seated on the Dust Drum.

D

R

A

I

N

Extended

Lip

Powerhead

Assembly

Vac Inlet

Dust

Drum

Extension Wand

Release Button

Accessory Nozzle

Ridges

CONNECT:

Locking Accessories

1. To Connect Accessory:

Your RIDGID Wet/Dry Vac includes

Locking Accessories to prevent the

Accessories from falling off when in use.

To connect the Accessories, align the

Nozzle Ridges of the Accessory with

the Release Button of your Extension

Wand. Press to secure the Nozzle to

the Extension Wand.

2. To Disconnect Accessory:

Twist the Nozzle and Extension Wand

to disengage the Nozzle Ridges and

pull. You may also press the Release

Button and pull to disengage.

Accessory Nozzle

Ridges

Extension Wand

Release Button

DISCONNECT:

SP7037-1 HD16000 ESF.indd 7 9/4/19 12:50 PM

8

ASSEMBLY

Inserting / Removing the

Tug-A-Long Positive Locking

Hose with Dual-Flex

1. To Insert Hose: Locate the end of the

Tug-A-Long Positive Locking Hose with

Dual-Flex and align it with the Drum Inlet.

Position the Hose Release Button with

the Ridges on the Vac Inlet. Push the

Hose end straight into the Vac Inlet until

the Hose Release Button fully engages

the Inlet Ridges.

D

R

A

I

N

D

R

A

I

N

Drum

Inlet

Ridges

Tug-A-Long Positive

Locking Hose with Dual-Flex

Hose Release Button

INSERT

HOSE

D

R

A

I

N

D

R

A

I

N

A

Inlet

Ridges

REMOVE

HOSE

Hose

Release

Button

B

2. To Remove Hose: Rotate the end of

the Tug-A-Long Positive Locking Hose

with Dual-Flex in either direction to

release the Hose Latch from the Inlet

Ridges (A). Press the Hose Release

Button and pull the Hose end straight

out of the Vac Inlet (B).

SP7037-1 HD16000 ESF.indd 8 9/4/19 12:50 PM

9

ASSEMBLY

Positioning Detachable Blower

(Powerhead Assembly)

1. To Remove the Detachable Blower

from the Powerhead Assembly, press

down on the Detachable Blower Latch

under the Detachable Blower Handle

and lift the Blower off the Powerhead

Assembly of the Vac.

Detachable

Blower Handle

TO REMOVE:

ROTATE

DETACHABLE

BLOWER UP

Detachable

Blower Latch

TO REMOVE:

PRESS DOWN ON

DETACHABLE

BLOWER LATCH

2. To Replace the Detachable Blower

onto the Powerhead Assembly, position

Detachable Blower above the indented

area of the Powerhead Assembly.

Rotate the Detachable Blower down

until the travel of the unit stops.

3. Lightly press down on the Detachable

Blower Handle until you hear the

“snap” of the Detachable Blower Latch

engaging the Detachable Blower.

The Detachable Blower is now latched

to the Powerhead Assembly.

Detachable

Blower Handle

TO REPLACE:

ROTATE

DETACHABLE

BLOWER DOWN

Detachable

Blower Latch

D

R

A

I

N

D

R

A

I

N

Detachable

Blower Latch

Detachable

Blower Handle

Powerhead

Assembly

SP7037-1 HD16000 ESF.indd 9 9/4/19 12:50 PM

OPERATION

After you plug the Power Cord into the

Outlet, turn the unit on by sliding the

Switch from position “O” to position “l”:

=

OFF

=

ON

Polarized Plug

To reduce the risk of electric shock,

this Appliance has a Polarized Plug

(one blade is wider than the other).

This Plug will fit in a Polarized Outlet

only one way. If the Plug does not fit fully

in the Outlet, reverse the Plug. If it still does

not fit, contact a qualified electrician to

install the proper Outlet. Do not change the

Plug in any way.

"ON"

Switch

"OFF"

Detachable

Blower Handle

10

CAUTION: To reduce the risk of hearing damage, wear ear

protectors when using the Vac/Blower for extended time or in a noisy area.

WARNING:

To reduce the risk of fire, explosion, or damage to Vac:

• Do not leave Vac running while unattended - you may fail to notice important

signs indicating abnormal operation such as loss of suction, debris/liquid

exiting the exhaust, or abnormal motor noises. Immediately stop using Vac

if you notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off suction.

• Sparks inside the motor can ignite airborne flammables. Do not operate

Vac near flammable liquids or in areas with flammable gases, vapors, or

explosive/airborne dust. Flammable liquids, gases, and vapors include:

lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol,

and aerosol sprays. Explosive dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.

• Do not leave sawdust or rags with stain or polyurethane residue inside Vac.

Empty drum after picking up these potentially self-heating materials.

WARNING: To reduce the risk of electric shock or injury:

• Do not expose to rain or allow liquid to enter motor compartment.

Store indoors.

• Do not handle plug, switch, or Vac with wet hands.

• Unplug Vac before servicing. If your Vac is not working as it should, has

missing parts, has been dropped, damaged, left outdoors, or dropped into

water, return it to an authorized service center or call customer service.

• When using an extension cord, use only outdoor-rated cords that are in good

condition. Do not allow the connection to come into contact with liquid.

!

SP7037-1 HD16000 ESF.indd 10 9/4/19 12:50 PM

Vacuuming Liquids

1. Vacuuming up small amounts of liquid

(less than 2” (5 cm) collected in Dust

Drum) does not require Filter removal.

2. When larger amounts of liquid are to

be picked up, remove the Filter, but

not the Filter Cage or Float, to prevent

the Filter from becoming saturated with

liquid. If the Filter becomes saturated,

you may see “mist” coming from the

Blowing Port.

3. When the Drum is “full” the Float will

rise and cut off airflow. The motor

sound will rise in pitch and its speed

will increase indicating the Drum is

“full”. Turn OFF the Vac and unplug the

power cord before emptying the Drum.

4. Following use of Vac for wet pick up,

allow Filter to dry completely to avoid

mildew and Filter damage.

11

OPERATION

Vacuuming Dry Materials

1. The Filter must always be correctly

installed to avoid leaks and possible

Vac damage.

2. To maintain peak performance when

vacuuming fine dust, clean the Drum

and Filter regularily.

NOTE: Do not use a wet Filter when

picking up dry material. The Filter will

quickly clog and be difficult to clean.

3. If the Filter is wet, you must allow it to

dry completely or replace it with a dry

Filter before using the Vac to pick up

dry material.

IMPORTANT: To reduce the risk of

damage to the Vac, do not run Motor with

Float in raised position.

WARNING:

Do not operate without filter cage

and float, as they prevent liquid from

entering the impeller and damaging

the motor.

!

SP7037-1 HD16000 ESF.indd 11 9/4/19 12:50 PM

12

Emptying the Drum

D

R

A

I

N

D

R

A

I

N

Drain Cap

Latches (2)

Powerhead

Assembly

Drum

1. Unplug Power Cord from power source.

2. The Vac comes equipped with a Drain

for easy emptying of liquids. Position the

Vac near a suitable drain or receptacle

and remove the Drain Cap.

3. Remove the Powerhead Assembly by

pulling outward at the top of the two

Latches.

4. Lift Powerhead Assembly from the Dust

Drum and set aside.

5. Use the Dust Drum Handles located

at the bottom of the Dust Drum to lift

and empty into a proper waste disposal

container.

NOTE: Do not carry the Vac by the

Detachable Blower Handle when the Vac

is full.

OPERATION

Moving the Wet/Dry Vac

Should it become necessary to pick the

Vac up to move it, the Drum Catch under

the Handles on the sides of the Dust Drum

are used to lift.

To maneuver the Vac, the Detachable

Blower Handle above the Vac Inlet can

be used.

D

R

A

I

N

D

R

A

I

N

Drum

Catch (2)

Detachable

Blower Handle

Vac Inlet

WARNING:

To reduce the risk of injury from

accidental starting, unplug power

cord before emptying the drum.

!

WARNING:

To reduce the risk of back injury

or falls, do not lift a Vac heavy

with liquid or debris. Scoop or drain

enough contents out to make the

Vac light enough to lift comfortably.

!

SP7037-1 HD16000 ESF.indd 12 9/4/19 12:50 PM

13

OPERATION

1. Familiarize yourself with the Detachable

Blower portion of your Wet/Dry Vac.

2. Remove the Detachable Blower of

your Vac by pressing down on the

Detachable Blower Latch under the

Handle of the Detachable Blower and

lift by the Handle.

Detachable

Blower Handle

TO REMOVE:

ROTATE

DETACHABLE

BLOWER UP

Detachable

Blower Latch

TO REMOVE:

PRESS DOWN ON

DETACHABLE

BLOWER LATCH

Blowing Feature

Your Wet/Dry Vac has a “Detachable

Blower.” It has the capability to be used

as a Dedicated Blower for yard work, patio

cleanup, and garage applications to blow

dust and other debris.

WARNING:

To reduce the risk of injury to

bystanders, keep them clear of

blowing debris.

WARNING:

Always wear safety eyewear

complying with ANSI Z87.1 (or in

Canada, CSA Z94.3) before using as

a blower.

CAUTION:

Wear a dust mask if blowing creates

dust which might be inhaled.

CAUTION:

To reduce the risk of hearing damage,

wear ear protectors when using the

Vac/Blower for extended time or in a

noisy area.

!

SP7037-1 HD16000 ESF.indd 13 9/4/19 12:50 PM

14

OPERATION

- OR -

2. The Wet/Dry Vac may also be used

for blowing using the seven-foot Hose

supplied with the Wet/Dry Vac. Install

the Push Button end of the Vac Hose

in the Blowing Port of the Detachable

Blower. For added control, an Extension

Wand and/or Car Nozzle can be added

to the opposite end of the Hose. The

unit is ready for blowing applications.

Using the Detachable Blower

for “Blowing”

Two suggested methods of using the

Blower are:

1. Insert the round end of the Blower

Wand into the Blowing Port of the

Detachable Blower and turn clockwise

to lock.

Car

Nozzle

Hose

Detachable

Blower Port

Dusk Mask

Detachable

Blower Port

Blower

Wand

TURN CLOCKWISE

TO LOCK

Goggles

3. Turn the Blower “ON” by sliding the

Switch in the Handle of the Blower to

the “I” position.

"ON"

Switch

"OFF"

Detachable

Blower Handle

SP7037-1 HD16000 ESF.indd 14 9/4/19 12:50 PM

15

Accessory Storage

1. The Extension Wands and other

Accessories can be stored by placing

them over the Posts on the Four Caster

Feet (front and back).

2. To remove, twist and pull up on the

Extension Wand or Accessory.

ACCESSORY & HOSE STORAGE

D

R

A

I

N

D

R

A

I

N

Caster

Feet

Posts (4)

Power Cord

& Plug

Detachable Blower

Cord Wrap Tabs (2)

Cord Storage

To store the Cord, wrap it around the

Detachable Blower Cord Wrap Two Tabs.

Secure the Cord using the Cord Clip on

the Plug.

Accessory

Caddy

Accessories

3. For extra storage of Accessories use

the Accessory Caddy. The Blower

Wand fits the center opening while

other Accessories can be snapped into

the two side Clips.

SP7037-1 HD16000 ESF.indd 15 9/4/19 12:50 PM

16

ACCESSORY & HOSE STORAGE

Hose Storage

The Tug-A-Long Positive Locking Hose

with Dual-Flex may be stored around the

Powerhead Assembly and snapped into the

Hose Storage Clip, located on the rear of the

Powerhead Assembly.

D

R

A

I

N

D

R

A

I

N

Powerhead Assembly

Tug-A-Long

Positive Locking

Hose with

Dual-Flex

Tug-A-Long Positive

Locking Hose with

Dual-Flex

Rear Hose

Storage Clip

WARNING:

Do not put any object into ventilation

openings. Do not vacuum with any

ventilation openings blocked; keep

free of dust, lint, hair or anything that

may reduce air flow.

!

CAUTION:

Do not operate vacuum while the

hose is still wrapped around the

powerhead assembly in the storage

position.

!

SP7037-1 HD16000 ESF.indd 16 9/4/19 12:50 PM

17

Detachable Blower Intake

After using the Detachable Blower of your

Wet/Dry Vac, examine the bottom of the

Blower for dust and debris. Check to see

if the Intake to the Blower has debris stuck

to the Plastic Vents and Foam Pad.

To clean the Foam Pad under the Intake

Shield of the Detachable Blower:

1. Remove the Three Screws holding the

Intake Shield.

2. Lift the Intake Shield off and set aside.

3. Lift the Foam Pad away from the

Detachable Blower.

4. Remove the Foam Pad and clean in

warm soapy water or brush debris

away. Allow Foam Pad to dry.

5. Examine Foam Pad for reuse. If you

need to replace it, check on-line at

store.ridgid.com/wetdry.

Foam Pad

Intake

Shield

Screws (3)

6. Replace Foam Pad by reversing Steps

1 thru 4.

7. Reinstall Intake Shield and 3 Screws.

The unit is ready for use.

MAINTENANCE

WARNING:

Do not put any object into ventilation

To reduce the risk of injury from

accidental starting, unplug power

cord before changing or cleaning

filter or foam pad.

!

DANGER:

Do not operate without reinstalling

the intake shield.

!

SP7037-1 HD16000 ESF.indd 17 9/4/19 12:50 PM

18

MAINTENANCE

NOTE: The Filter is made of high quality

paper designed to stop small particles of

dust. The Filter can be used for dry pick

up or small amounts of liquid. Handle

the Filter carefully when removing or

installing. Creases in the Filter Pleats may

occur from installation but will not affect

the performance of the Filter.

3. Firmly press the Qwik Lock™ Integrated

Filter Plate down around the Qwik

Lock™ Stud until it snaps into place.

NOTE: Failure to properly seat the

bottom Gasket and Integrated Filter Plate

to the Filter Cage could result in debris

bypassing the Filter.

Filter Removal:

1. Place fingers under the two Filter Tabs

of the Qwik Lock™ Filter.

2. With one thumb on the Qwik Lock™

Stud, which protrudes through the

integrated Filter Plate. Lift up on the

Two Filter Tabs while pushing down on

the Stud.

3. This action will cause the Filter to

release from the Filter Cage. Slide

Filter off Filter Cage.

IMPORTANT: To avoid Blower Wheel

and Motor Damage always reinstall Filter

before using Vac for dry material pickup.

Filter Installation:

1. Carefully slide the Qwik Lock™ Filter

over the Filter Cage while aligning the

Qwik Lock™ Stud on the Filter Cage

with the center hole in the Qwik Lock™

Integrated Filter Plate.

2. Make sure the Rubber Gasket at the

bottom of the Qwik Lock™ Filter seats

around the base of the Filter Cage.

Qwik Lock™

Stud

Rubber

Gasket at

Bottom of

Filter

PUSH

DOWN

PULL

UP

Filter

Tabs (2)

Integrated Filter Plate

with Center Hole

PULL

UP

Filter Cage

Float

Powerhead

Assembly

Your Filter should be cleaned often to

maintain peak Vac performance.

Filter

Removal & Installation of the

Qwik Lock™ Filter

WARNING:

To reduce the risk of injury from

accidental starting, unplug power

cord before changing or cleaning

filter.

!

WARNING:

Do not operate without filter cage

and float, as they prevent liquid from

entering the impeller and damaging

the motor.

!

SP7037-1 HD16000 ESF.indd 18 9/4/19 12:50 PM

19

MAINTENANCE

Cleaning A Dry Filter

1. Some removal of dry debris can be

accomplished without removing the

Filter from the Vac. Slap your hand on

top of the Lid while the Vac is turned

off.

2. For best cleaning results due to

accumulated dust, clean the Filter in

an open area. Cleaning SHOULD be

done outdoors and not in the living

quarters.

3. After Filter removal from Vac, remove

the dry debris by gently tapping Filter

against the inside wall of your Dust

Drum. The debris will loosen and fall.

4. For thorough cleaning of Dry Filter

with fine dust (no debris), run water

through it as described under “Cleaning

A Wet Filter”.

Cleaning A Wet Filter

After Filter is removed, run water through

the Filter from a hose or spigot. Take care

that water pressure from the hose is not

strong enough to damage Filter.

IMPORTANT: After cleaning, check the

Filter for tears or small holes. Do not use a

Filter with holes or tears in it. Even a small

hole can allow dust to come out of your

Vac. Replace it immediately.

Allow the Filter to dry completely before

reinstalling and storing the Vac or picking

up dry debris.

WARNING:

To assure product SAFETY and RELIABILITY, any other maintenance, repairs and

adjustments should be performed by Authorized Service Centers, always using

RIDGID replacement parts.

!

SP7037-1 HD16000 ESF.indd 19 9/4/19 12:50 PM

16 U.S. Gallon (60 Liter) Detachable Wet/Dry Vac

Model Number HD16000

Electrical Ratings:

120 V 12.0 A 60 Hz

RIDGID parts are available on-line at store.ridgid.com/wetdry

Always order by Part Number - Not by Key Number

REPAIR PARTS

This product has a 90 day Satisfaction Guarantee Policy

as well as a Limited Lifetime Warranty.

For Warranty and Policy details go to

RIDGID.com/VacWarranty or call 1-800-4-RIDGID.

Part No. SP7037 Form No. SP7037-1 Printed in Mexico 09/19

©

2019 Emerson

www.RIDGID.com

!

WARNING:

SERVICING OF DOUBLE-INSULATED WET/DRY VAC

In a double-insulated Wet/Dry Vac, two systems of insulation are provided

instead of grounding. No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added. Servicing a double-

insulated Wet/Dry Vac requires extreme care and knowledge of the system,

and should be done only by qualified service personnel. Replacement parts

for a double-insulated Wet/Dry Vac must be identical to the parts they replace.

Your double-insulated Wet/Dry Vac is marked with the words “DOUBLE

INSULATED” and the symbol (square within a square) may also be

marked on the appliance.

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

WARNING:

To reduce the risk of injury from electrical shock, unplug power cord before

servicing the electrical parts of the Wet/Dry Vac.

!

WARNING:

All disassembly and repairs should be performed by qualified personnel.#

!

SP7037-1 HD16000 ESF.indd 20 9/4/19 12:50 PM

La page charge ...

RIDGID HD1600D Manuel utilisateur

Ce manuel convient également à

RIDGID HD1600D Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents